FCC Part 15 Subpart B

Transcription

1 Report No.: 15A111603E-F Page 1 of 23 Test Report FCC Part 15 Subpart B for Electromagnetic Interference of Product: Managed PoE Industrial Ethernet Switch Trade Name: N/A Model Number: IS-DG512P-2F-8; IS-DG510P-8; IS-DG512P-4F-8; IS-DG510P-4F-6; IS-DG510P-2F-8; IS-DG508P-2F-6 Prepared for ISON Technology Co., Ltd. Room6, 20F, No.77, Sec. 1. Xintai 5th Rd., Xizhi Dist., New Taipei City 22101, Taiwan Prepared by No. 5-2, Lin 1, Tin-Fu, Lin-Kou Dist., New Taipei City, Taiwan 244, R.O.C. TEL: FAX: Remark: 1. The test report consists of 23 pages in total. It shall not be reproduced except in full, without the written approval of IETC. This document may be altered or revised by IETC only, and shall be noted in the revision section of the document. The test result in the report is subjected only to the test sample. 2. This test report results are deemed satisfactory evidence of compliance with Industry Canada Interference-Causing Equipment Standard ICES-003.

2 Report No.: 15A111603E-F Page 2 of 23 Table of Contents 1 General Information Description of Equipment Under Test Details of Tested Supporting System Test Facility Measurement Uncertainty Measured Mode Configuration of EUT Setup Test Step of EUT 8 2 Power Line Conducted Emission Measurement Instrument Block Diagram of Test Configuration Conducted Limits Instrument Configuration Configuration of Measurement Test Result 10 3 Radiated Emission Measurement (Below 1GHz) Instrument Block Diagram of Test Configuration Radiated Limits Instrument Configuration Configuration of Measurement Test Result 14 4 Radiated Emission Measurement (Above 1GHz) Instrument Block Diagram of Test Configuration Radiated Limit Instrument Configuration Configuration of Measurement Test Result 18 5 Photographs of Measurement Conducted Emission Measurement Radiated Emission Measurement 22 6 Photographs of EUT 23

3 Report No.: 15A111603E-F Page 3 of 23 Statement of Compliance Applicant: Manufacturer: Product: Model No.: Tested Power Supply: ISON Technology Co., Ltd. ISON Technology Co., Ltd. Managed PoE Industrial Ethernet Switch IS-DG512P-2F-8; IS-DG510P-8; IS-DG512P-4F-8; IS-DG510P-4F-6; IS-DG510P-2F-8; IS-DG508P-2F-6 DC 48V Date of Final Test: Oct. 20, 2015 Revision of Report: Rev. 01 Measurement Procedures and Standards Used: 47 CFR FCC Part 15 Subpart B ANSI C63.4: 2014 ICES-003 Issue 5 CAN/CSA-CISPR The measurement results in this test report were performed at Interocean EMC Technology Corp. The responsibility of measurement result is only subjected to the test sample. This report shows the EUT is technically compliance with the above official standards. This report shall not be partial reproduced without written approval by Interocean EMC Technology Corporation. Report Issued: 2015/11/20 Project Engineer: Approved: Evans Chang Wilson Chang

4 Report No.: 15A111603E-F Page 4 of 23 1 General Information 1.1 Description of Equipment Under Test Product : Managed PoE Industrial Ethernet Switch Model Number Applicant Manufacturer : IS-DG512P-2F-8; IS-DG510P-8; IS-DG512P-4F-8; IS-DG510P-4F-6; IS-DG510P-2F-8; IS-DG508P-2F-6 : ISON Technology Co., Ltd. Room6, 20F, No.77, Sec. 1. Xintai 5th Rd., Xizhi Dist., New Taipei City 22101, Taiwan : ISON Technology Co., Ltd. Room6, 20F, No.77, Sec. 1. Xintai 5th Rd., Xizhi Dist., New Taipei City 22101, Taiwan Power Supply : 10 ~ 60 Vdc Date of Test : Oct. 08 ~ 20, 2015 Additional Description : 1.) The Model Number IS-DG512P-2F-8 is representative selected in the test and included in this report. 2.) The differences for all models included in this report are as follows: Model Total Port # Ethernet Ports PoE Port (30W) PoE Port (60W) Non PoE SFP Port PoE PoE type IS-DG508P-2F Type2 IS-DG510P-2F x 2 Type4 IS-DG512P-4F-8 IS-DG510P-4F-6 IS-DG512P-2F-8 IS-DG510P x 4 YES Type Type4 Power input range Dual power input (10 ~ 60 Vdc) 3.) The difference between both series model IS-DG512P-4F-8; IS-DG510P-4F-6 is different market. 4.) The difference between both series model IS-DG512P-2F-8; IS-DG510P-8 is different market. 5.) For more detail specifications about EUT, please refer to the user s manual.

5 Report No.: 15A111603E-F Page 5 of Details of Tested Supporting System Link PC PC18 Model Number : IBM ThinkCentre 8175-OVE Serial Number : 99LBVYC CPU Speed : Pentium 4 Celeron D 2.8GHz EMC Compliance : CE, FCC, C-Tick, UL, BSMI: R33026 Manufacturer : IBM RAM : 256M*1 Hard Disk Driver : 80GB Power Cord : Non-shielded, Detachable, 1.8m, w/o core PC31 Model Number : SGH017PFWL CPU Speed : Intel Core 2 Duo E5400 RAM : 2GB DDR3 1333MHz EMC Compliance : CE, TUV, NCC, BSMI: R33275 Hard Disk Driver : 250GB Serial ATA2 3.0Gb/s 7200rpm Manufacturer : HP Switching Power Supply : LiteOn, PS HP, 320W Power Cord : Non-shielded, Detachable, 1.8m, w/o core PD Manufacturer : ISON Test Cable Power Cord *1 : Non-shielded, Detachable, 1.8m, w/o core RJ45 Cable *4 : Non-shielded, Detachable, 3m, w/o core RJ45 Cable *3 : Non-shielded, Detachable, 0.13m, w/o core Fiber Cable *2 : Non-shielded, Detachable, 1.2m, w/o core

6 Report No.: 15A111603E-F Page 6 of Test Facility Site Description : Conducted 1 OATS 1 Chamber 3 Name of Firm : Company web : Location : No. 5-2, Lin 1, Tin-Fu, Lin-Kou Dist., New Taipei City, Taiwan 244, R.O.C. Site Filing : Federal Communication Commissions USA Registration No.: (OATS 1, 2, 3 & Chamber 3) Designation No.: TW1020 Industry Canada (IC) OUR FILE: Registration No. (OATS 1): Site# 4437A-1 Registration No. (OATS 3): Site# 4437A-3 Registration No. (Chamber 3): Site# 4437A-5 Registration No. (OATS 5): Site# 4437A-6 Voluntary Control Council for Interference by Information Technology Equipment (VCCI) Japan Member No.: 1349 Registration No. (Conducted Room): C-1094 Registration No. (Conducted Room): T-1562 Registration No. (OATS 1): R-1040; G-274 Site Accreditation : Bureau of Standards and Metrology and Inspection (BSMI) Taiwan, R.O.C. Accreditation No.: SL2-IN-E-0026 for CNS13438 / CISPR 22 SL2-IN-E-0026 for CNS / IEC SL2-R1-E-0026 for CNS13439 / CISPR 13 SL2-R2-E-0026 for CNS13439 / CISPR 13 SL2-A1-E-0026 for CNS / CISPR 14-1 SL2-L1-E-0026 for CNS / CISPR 15 Taiwan Accreditation Foundation (TAF) Accreditation No.: 1113 Vehicle Safety Certification Center (VSCC) Approval No.: TW TüV NORD Certificate No: TNTW0801R-04

7 Report No.: 15A111603E-F Page 7 of Measurement Uncertainty Item Value Conduction 1: Conducted Emission - AMN (9 khz to 30 MHz) 2.98 db OATS 1: Radiated Emission Test (30 MHz to 1 GHz) 4.84 db OATS 3: Radiated Emission Test (30 MHz to 1 GHz) 4.70 db OATS 5: Radiated Emission Test (30 MHz to 1 GHz) 4.70 db Chamber 3: Radiated Emission Test (30 MHz to 1 GHz) 4.86 db Radiated Emission Test (above 1 GHz) 5.12 db

8 Report No.: 15A111603E-F Page 8 of Measured Mode The test mode for final test is as following: Mode 1: PoE Mode (Model No.: IS-DG512P-2F-8) 1.6 Configuration of EUT Setup Connected to mains EUT PD Link PC Link PC 1.7 Test Step of EUT Setup the EUT and peripheral as above Turn on the power of EUT Executed the test.

9 Report No.: 15A111603E-F Page 9 of 23 2 Power Line Conducted Emission Measurement 2.1 Instrument Instrument Manufacturer Model Serial No. Next Cal. Date EMI Test Receiver Rohde & Schwarz ESCS /10/20 RF Cable HARBOUR RG58/U CBL /07/27 L.I.S.N. Schwarzbeck NNLK /09/01 L.I.S.N. Schaffner MN2050D /08/27 Note: The above equipments are within the valid calibration period. 2.2 Block Diagram of Test Configuration Rear of EUT to be flush with rear of table top 0.1m Non-conductive table EMI Test Receiver EUT Peripheral 0.8 m to ground plane RF Cable 0.8 m LISN 0.4 m LISN Power Cord Bonded to horizontal ground plane 0.4 m to vertical ground reference plane Bonded to horizontal ground plane Vertical ground reference plane 2.3 Conducted Limits Frequency Class A (dbμv) Class B (dbμv) (MHz) Q.P. (Quasi-Peak) A.V. (Average) Q.P. (Quasi-Peak) A.V. (Average) 0.15 ~ to to ~ ~

10 Report No.: 15A111603E-F Page 10 of Instrument Configuration Set the EMI test receiver frequency range from 150 khz to 30 MHz Set the EMI test receiver bandwidth at 9kHz Set the EMI test receiver detector as Quasi-Peak (Q.P.) and Average (AV). 2.5 Configuration of Measurement The EUT was placed on a non-conductive table whose total height equaled 80cm and vertical conducting plane located 40cm to the rear of the EUT The EUT was connected to the main power through Line Impedance Stabilization Networks (LISN). This setup provided a 50ohm/50 H coupling impedance for the measuring equipment. The auxiliary equipment was also connected to the main power through a LISN that provided a 50ohm/50 H coupling impedance with 50ohm termination. (Refer to the block diagram of the test setup and photographs.) The conducted disturbance was measured between the phase lead and the reference ground, and between the neutral lead and reference ground. The initial testing identified the frequency that has the highest disturbance relative to the limit while operating the EUT in typical modes of operation and cable positions in a test setup representative of typical system configuration The identification of the frequency of highest disturbance with respect to the limit was found by investigating disturbances at a number of significant frequencies. The probable frequency of maximum disturbance had been found and that the associated cable and EUT configuration and mode of operation had been identified. 2.6 Test Result PASS. The final test data is shown as following pages. Factor = Insertion Loss + Cable Loss Level = Reading + Factor Margin = Level - Limit

11 Report No.: 15A111603E-F Page 11 of 23 Power Line Conducted Test Data CLIENT: ISON Technology Co., Ltd. OPERATOR: Ron EUT: Managed PoE Industrial Ethernet Switch TEST SITE: Conducted 1 MODEL: IS-DG512P-2F-8 POLARIZATION: Line RATING: DC 48V TEMP/HUM: 24.3 C / 52% COMMENT: Test Mode: Mode 1: PoE Mode (Model No.: IS-DG512P-2F-8) Data:141 J:\E3_28\2015\ISON.EM Item Freq. Reading Factor Level Limit Margin Remark Mark MHz dbuv db dbuv dbuv db QP Average QP Average QP Average QP Average QP Average QP Average

12 Report No.: 15A111603E-F Page 12 of 23 Power Line Conducted Test Data CLIENT: ISON Technology Co., Ltd. OPERATOR: Ron EUT: Managed PoE Industrial Ethernet Switch TEST SITE: Conducted 1 MODEL: IS-DG512P-2F-8 POLARIZATION: Neutral RATING: DC 48V TEMP/HUM: 24.3 C / 52% COMMENT: Test Mode: Mode 1: PoE Mode (Model No.: IS-DG512P-2F-8) Data:142 J:\E3_28\2015\ISON.EM Item Freq. Reading Factor Level Limit Margin Remark Mark MHz dbuv db dbuv dbuv db QP Average QP Average QP Average QP Average QP Average QP Average

13 Report No.: 15A111603E-F Page 13 of 23 3 Radiated Emission Measurement (Below 1GHz) 3.1 Instrument Instrument Manufacturer Model Serial No. Next Cal. Date EMI Test Receiver Rohde & Schwarz ESVS / /10/29 Biconical Antenna Schwarzbeck VHA 9103 & BBA 9106 VHA /07/05 Log Antenna Schwarzbeck UHALP 9108-A 9108-A /07/19 Pre-Amplifier Agilent 8447D 2944A /04/28 RF Cable EMCI EMC8D-NM-NM /02/15 RF Cable Mini-Circuits CBL-3FL-NMNM CBL /08/28 RF Cable Insulated Wire CBL59 CBL /01/21 Note: The above equipments are within the valid calibration period. 3.2 Block Diagram of Test Configuration Measurement Frequency under 1GHz 10m RF Cable 4 m EUT Pre-Amplifier 1 m Test table & Turntable 80 cm EMI Test Receiver Ground Plane

14 Report No.: 15A111603E-F Page 14 of Radiated Limits FCC Part 15 / ICES-003 (ANSI C63.4) Class A (10m) Class B (3m) Frequency Field Strength Quasi-Peak Field Strength Quasi-Peak (MHz) (μv/m) db(μv/m) (μv/m) db(μv/m) 30 ~ ~ ~ above CISPR 22 / CAN/CSA-CISPR Class A Class B Frequency (MHz) Quasi-Peak db(μv/m) Quasi-Peak db(μv/m) 30 ~ ~ ** According to 47 CFR FCC Part (g) as refer to CISPR 22 Limits and method of measurement. ** According to ICES-003 Issue 5 5.(A)(i) as refer to CAN/CSA-CISPR Limits and method of measurement. 3.4 Instrument Configuration Set the EMI test receiver frequency range from 30 MHz to 1000 MHz Set the EMI test receiver bandwidth at 120 khz Set the EMI test receiver detector as Quasi-Peak (Q.P.). 3.5 Configuration of Measurement The EUT was placed on a non-conductive table whose total height equaled 80cm. The turntable can rotate 360 degree to determine the position of the maximum emission level The EUT was set 10 meters away from the receiving antenna that was mounted on a non-conductive mast. The antenna can move up and down between 1 to 4 meters to find out the maximum emission level The initial testing identified the frequency that has the highest disturbance relative to the limit while operating the EUT in typical modes of operation and cable positions in a test setup representative of typical system configuration The identification of the frequency of highest emission with respect to the limit was found by investigating emissions at a number of significant frequencies. The probable frequency of maximum emission had been found and that the associated cable and EUT configuration and mode of operation had been identified. 3.6 Test Result PASS. The final test data is shown as following pages. Factor = Antenna Factor + Cable Loss - Preamplifier Gain Level = Reading + Factor Margin = Level - Limit

15 Report No.: 15A111603E-F Page 15 of 23 Radiated Emission Measurement Data CLIENT: ISON Technology Co., Ltd. OPERATOR : Ceres EUT: Managed PoE Industrial Ethernet Switch TEST SITE : OATS 1 MODEL: IS-DG512P-2F-8 TEST DISTANCE : 10m RATING: DC 48V POLARIZATION : HORIZONTAL COMMENT: Test Mode: Mode 1: PoE Mode (Model No.: IS-DG512P-2F-8) TEMP/HUM : 24.3 /62% Data:44 C:\e3\2015\ISON.EM Item Freq. Reading Factor Level Limit Margin Remark Mark MHz dbuv db dbuv/m dbuv/m db QP QP QP QP QP QP QP QP QP QP QP QP QP QP

16 Report No.: 15A111603E-F Page 16 of 23 Radiated Emission Measurement Data CLIENT: ISON Technology Co., Ltd. OPERATOR : Ceres EUT: Managed PoE Industrial Ethernet Switch TEST SITE : OATS 1 MODEL: IS-DG512P-2F-8 TEST DISTANCE : 10m RATING: DC 48V POLARIZATION : VERTICAL COMMENT: Test Mode: Mode 1: PoE Mode (Model No.: IS-DG512P-2F-8) TEMP/HUM : 24.3 /62% Data:43 C:\e3\2015\ISON.EM Item Freq. Reading Factor Level Limit Margin Remark Mark MHz dbuv db dbuv/m dbuv/m db QP QP QP QP QP QP QP QP QP QP QP QP QP

17 Report No.: 15A111603E-F Page 17 of 23 4 Radiated Emission Measurement (Above 1GHz) 4.1 Instrument Instrument Manufacturer Model Serial No. Next Cal. Date Spectrum Analyzer R&S FSP /06/03 Horn Antenna Schwarzbeck BBHA D /10/20 Pre-Amplifier EMCI EMC /10/16 RF Cable Jye Bao N30N CBL /03/30 RF Cable HARBOUR 27478LL142 CBL /03/23 Note: The above equipments are within the valid calibration period. 4.2 Block Diagram of Test Configuration Measurement Frequency above 1GHz 3 m RF Cable 1~ 4 m Spectrum Analyzer Pre- Amplifier 1 m Test table & Turntable EUT 80 cm Ground Plane 4.3 Radiated Limit Class A (3m) Class B (3m) Frequency (MHz) Peak Average Peak Average db(μv/m) db(μv/m) db(μv/m) db(μv/m) Above

18 Report No.: 15A111603E-F Page 18 of Instrument Configuration Set the EMI test receiver frequency range above 1GHz Set the EMI test receiver bandwidths above 1GHz are at 1MHz All readings of the test receiver detector above 1GHz are average value. 4.5 Configuration of Measurement The EUT was set 3 meters for measuring frequency above 1GHz away from the receiving antenna that was mounted on a non-conductive mast The antenna set at 1.0 meter height and EUT was placed on a non-conductive table whose total height equaled 80cm. The turntable can rotate 360 degree to determine the position of the maximum emission level The initial testing identified the frequency that has the highest disturbance relative to the limit while operating the EUT in typical modes of operation and cable positions in a test setup representative of typical system configuration The identification of the frequency of highest emission with respect to the limit was found by investigating emissions at a number of significant frequencies. The probable frequency of maximum emission had been found and that the associated cable and EUT configuration and mode of operation had been identified. 4.6 Test Result PASS. The final test data is shown as following pages. Factor = Antenna Factor + Cable Loss - Preamplifier Gain Level = Reading + Factor Margin = Level - Limit

19 Report No.: 15A111603E-F Page 19 of 23 Radiated Emission Measurement Data CLIENT: ISON Technology Co., Ltd. OPERATOR : Mark EUT: Managed PoE Industrial Ethernet Switch TEST SITE : Chamber 3 MODEL: IS-DG512P-2F-8 TEST DISTANCE : 3m RATING: DC 48V POLARIZATION : HORIZONTAL COMMENT: Test Mode: Mode 1: PoE Mode (Model No.: IS-DG512P-2F-8) TEMP/HUM : 25 /53% Data:17 I:\e3\data\2015\ISON.EM Item Freq. Reading Factor Level Limit Margin Remark Mark MHz dbuv db dbuv/m dbuv/m db Peak Average Peak Average Peak Average

20 Report No.: 15A111603E-F Page 20 of 23 Radiated Emission Measurement Data CLIENT: ISON Technology Co., Ltd. OPERATOR : Mark EUT: Managed PoE Industrial Ethernet Switch TEST SITE : Chamber 3 MODEL: IS-DG512P-2F-8 TEST DISTANCE : 3m RATING: DC 48V POLARIZATION : VERTICAL COMMENT: Test Mode: Mode 1: PoE Mode (Model No.: IS-DG512P-2F-8) TEMP/HUM : 25 /53% Data:18 I:\e3\data\2015\ISON.EM Item Freq. Reading Factor Level Limit Margin Remark Mark MHz dbuv db dbuv/m dbuv/m db Peak Average Peak Average Peak Average

21 Report No.: 15A111603E-F Page 21 of 23 5 Photographs of Measurement 5.1 Conducted Emission Measurement Front View Rear View

22 Report No.: 15A111603E-F Page 22 of Radiated Emission Measurement Front View Rear View

23 Report No.: 15A111603E-F Page 23 of 23 6 Photographs of EUT Front View of EUT (Model No.: IS-DG512P-2F-8) Rear View of EUT (Model No.: IS-DG512P-2F-8)