CE RADIO TEST REPORT. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan

Transcription

1 SPORTON International Inc. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: / FAX: / CE RADIO TEST REPORT Applicant s company Applicant Address Manufacturer s company Manufacturer Address Realtek Semiconductor Corp. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Realtek Semiconductor Corp. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Product Name b/g RTL8187SE minicard Brand Name Realtek Model Name RTL8187SE Test Standard(s) ETSI EN V1.7.1 ( ) Test Freq. Range 2400 ~ MHz Received Date Dec. 18, 2007 Final Test Date Jan. 24, 2008 Submission Type Original Equipment Statement Test result included in this report is only for the b/g part of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ETSI EN V1.7.1 ( ). The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report Format Version: 01

2 Report : ER7D1808 Table of Contents 1. CERTIFICATE OF COMPLIANCE SUMMARY OF THE TEST RESULT GENERAL INFORMATION Product Details Accessories Table for Filed Antenna Table for Carrier Frequencies Table for Test Modes Table for Testing Locations Table for Supporting Units Table for Parameters of Test Software Setting Test Configurations TEST RESULT Equivalent Isotropic Radiated Power Measurement Maximum Spectral Power Density Measurement Frequency Range Measurement Transmitter Spurious Emissions Measurement Receiver Spurious Emissions Measurement LIST OF MEASURING EQUIPMENTS TEST LOCATION APPENDIX A. PHOTOGRAPHS OF EUT... A1 ~ A7 APPENDIX B. TEST PHOTOS... B1 ~ B3 Report Format Version: 01 Page : i of ii

3 Report : ER7D1808 History of This Test Report Original Issue Date: Feb. 01, 2008 Report : ER7D1808 No additional attachment. Additional attachment were issued as following record: Attachment Issue Date Description Report Format Version: 01 Page : ii of ii

4

5 Report : ER7D SUMMARY OF THE TEST RESULT Applied Standard: ETSI EN V1.7.1 ( ) Part Standard Clause Description of Test Result Under Limit Equivalent Isotropic Radiated Power Complies 0.07 db Power Spectral Density Complies 0.25 db Frequency Range Complies Transmitter Spurious Emissions Complies db Receiver Spurious Emissions Complies 1.33 db Test Items Uncertainty Remark Equivalent Isotropic Radiated Power (Conducted) ±0.8dB Confidence levels of 95% Power Spectral Density (Conducted) ±1.0dB Confidence levels of 95% Frequency Range ± Confidence levels of 95% Spurious Emissions 30MHz~1000MHz (Radiated) ±2.6dB Confidence levels of 95% Spurious Emissions 1GHz~18GHz (Radiated) ±2.6dB Confidence levels of 95% Temperature ±0.7 Confidence levels of 95% Humidity ±3.2% Confidence levels of 95% DC / AC Power Source ±1.4% Confidence levels of 95% Report Format Version: 01 Page : 2 of 37

6 Report : ER7D GENERAL INFORMATION 3.1. Product Details Items Description Power Type From Host System Modulation DSSS for IEEE b ; OFDM for IEEE g Data Modulation DSSS (BPSK / QPSK / CCK) ; OFDM (BPSK / QPSK / 16QAM / 64QAM) Data Rate (Mbps) DSSS (1/ 2/ 5.5/11) ; OFDM (6/9/12/18/24/36/48/54) Frequency Band 2400 ~ MHz Channel Number 13 EIRP Output Power 11b: dbm ; 11g: dbm Carrier Frequencies Please refer to section 3.4 Antenna Please refer to section Accessories N/A Report Format Version: 01 Page : 3 of 37

7 Report : ER7D Table for Filed Antenna Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) PK 3.95 Ant. Type PIFA Gain(dBi) DQ DQ PK 2.39 Ant. Type PIFA Gain(dBi) AR830WIPI02A PK 2.48 Ant. Type PIFA Gain(dBi) ARW62WIP101G PK 2.32 Ant. Type PIFA Gain(dBi) WDAN-GQMA6001-DF PK 3.64 Ant. Type PIFA Gain(dBi) NC3587 PK 2.86 Ant. Type PIFA Gain(dBi) AAFQ LK0 PK 0.79 Ant. Type PIFA Gain(dBi) EE PK 0.63 Ant. Type PIFA Gain(dBi) B G0003 PK 1.56 Ant. Type PIFA Gain(dBi) ASAA001 PK Ant. Type PIFA AR320WIPI02B ARUMPWIPI02 WDAN-GQMA6002-DF NC3586 HFT40-IV17 ASAW001 ASAT001 HFT40 Gain(dBi) HFT60 PK 2.82 Ant. Type PIFA HTL008 Gain(dBi) HTL017 PK Ant. Type PIFA TBN001 Gain(dBi) TBN003 PK 1.76 Ant. Type PIFA TIAN01 Gain(dBi) WNC001 PK 2.99 Ant. Type PIFA U40 WNC002 Gain(dBi) Report Format Version: 01 Page : 4 of U40

8 Report : ER7D Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) Ant. Type PIFA PK Gain(dBi) TFF-A011MPXX-361 Ant. Type PIFA PK Gain(dBi) 2.83 MCA50 PK 2.53 Ant. Type PIFA Gain(dBi) U50 U50 PK 2.29 Ant. Type PIFA Gain(dBi) MA-8 ( ) PK 0.11 Ant. Type PIFA Gain(dBi) SA-1( ) PK 0.21 Ant. Type PIFA Gain(dBi) L45II-WLAN PK 1.15 Ant. Type PIFA Gain(dBi) L55II-ID3 PK 0.95 Ant. Type PIFA MA-8 ( ) WDAN-GQMA3004-DF L55II-ID1 & ID2 L55II-ID4 Gain(dBi) L55 RI PK Ant. Type PIFA 42 W351 PK Ant. Type PIFA UM700-L Gain(dBi) W651 Gain(dBi) W815UI1 PK 0.8 Ant. Type PIFA 46 Gain(dBi) 1.68 L45 NB0040-K Note: (1) Due to Ant.1 ~ Ant. 47 are the same type antenna, only the higher gain antenna Ant.1 was tested and recorded in this report. (2) The EUT has diversity function; It supports both transmit and receive Antenna Diversity. Report Format Version: 01 Page : 5 of 37

9 Report : ER7D Table for Carrier Frequencies Frequency Band Channel Frequency MHz MHz MHz MHz MHz MHz 2400~2483.5MHz MHz MHz MHz MHz MHz MHz MHz 3.5. Table for Test Modes Preliminary tests were performed in different data rate to find the worst radiated emission. The data rate shown in the table below is the worst-case rate with respect to the specific test item. Investigation has been done on all the possible configurations for searching the worst cases. The following table is a list of the test modes shown in this test report. Test Items Mode Data Rate Channel Antenna Equivalent Isotropic Radiated Power 11b/BPSK 1 Mbps 1/7/13 1 Power Spectral Density 11g/BPSK 6 Mbps 1/7/13 1 Frequency Range 11b/BPSK 1 Mbps 1/ g/BPSK 6 Mbps 1/13 1 Transmitter/ Receiver Spurious Emissions 11g/BPSK 6 Mbps 13 1 (30MHz~1GHz) Transmitter Spurious Emissions 11b/BPSK 1 Mbps 1/13 1 (1GHz~12.75GHz) 11g/BPSK 6 Mbps 1/13 1 Receiver Spurious Emissions 11b/BPSK 1 Mbps 1 1 (1GHz~12.75GHz) 11g/BPSK 6 Mbps 13 1 Note: The product is restricted for indoor use only. Report Format Version: 01 Page : 6 of 37

10 Report : ER7D Table for Testing Locations Test Site Site Category Location Test Site Site Category Location 05CH01-HY FAC Hwa Ya TH01-HY OVEN Room Hwa Ya Open Area Test Site (OATS); Semi Anechoic Chamber (SAC); Fully Anechoic Chamber (FAC). Please refer section 6 for Test Site Address Table for Supporting Units Support Unit Brand Model FCC ID Notebook ASUS A8H PPD-AR5BXB Table for Parameters of Test Software Setting During testing, Channel & Power Controlling Software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product. Power Parameters of IEEE b/g Test Software Version Realtek Frequency 2412 MHz 2442 MHz 2472 MHz IEEE b IEEE g Test Configurations 1 USB x 2 RJ-11 RJ-45 LPT VGA RS232 DC Notebook 3 2 EUT EXPRESS CARD Ant Ant 1. Power line, 1.8m Non-shielded 2 Antenna cable, 0.72m Non-shielded 3. Antenna cable, 0.53m Non-shielded Report Format Version: 01 Page : 7 of 37

11 Report : ER7D TEST RESULT 4.1. Equivalent Isotropic Radiated Power Measurement Limit The equivalent isotropic radiated power is defined as the total power of the transmitter. The equivalent isotropic radiated power shall be equal to or less than -10dBW (100 mw) e.i.r.p. This limit shall apply for any combination of power level and intended antenna assembly Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the power meter. Power Meter Parameter Filter Measurement time Used Average Sensor Setting Auto s ~ 26 s NRV-Z Test Procedures 1. Since a temporary antenna connector can be attached on the RF output port, so conducted measurement method was used in this case. 2. A wide band power meter with a matched thermocouple detector was used to directly measure the output power from the RF output port of the EUT in continuously transmitting mode. 3. The EIRP = A+G+10*log(1/x), where A is the power measured in (2), G is the gain of the antenna of the EUT in dbi and x is the duty cycle of the EUT in continuously transmitting mode. 4. The measurement shall be repeated at the lowest, the middle, and the highest channel of the stated frequency range. These measurements shall also be performed at normal and extreme test conditions Test Setup Layout Report Format Version: 01 Page : 8 of 37

12 Report : ER7D Test Deviation There is no deviation with the original standard EUT Operation during Test The EUT was programmed to be in continuously transmitting mode Test Result Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations b/g Test Date Jan. 24, 2008 Configuration IEEE b Test Conditions Average EIRP mean power (dbm) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 55 V max (V) V min (V) V max (V) V min (V) Max mean Power Limits Result 20dBm (-10dBW) Complies Configuration IEEE g Test Conditions Average EIRP mean power (dbm) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 55 V max (V) V min (V) V max (V) V min (V) Max mean Power Limits Result 20dBm (-10dBW) Complies Report Format Version: 01 Page : 9 of 37

13 Report : ER7D Maximum Spectral Power Density Measurement Limit The maximum spectral power density is defined as the highest level of power in Watts per Hertz generated by the transmitter within the power envelope. For wide band modulations other than FHSS (e.g. DSSS, OFDM, etc.), the maximum spectrum power density is limited to 10 mw per MHz e.i.r.p Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer and power meter. Spectrum Analyzer Attenuation Span Frequency RB VB Detector Trace Sweep Time Setting 20~30dB 0 MHz 1 MHz 1 MHz Positive Peak Max Hold Auto Power Meter Parameter Filter Measurement time Used Average Sensor Setting Auto s ~ 26 s NRV-Z Test Procedures 1. Pre-calibration for the spectrum analyzer has to be done first through a CW signal of the measured carrier frequency with 10dBm power strength. 2. A power meter is connected on the IF output port of the spectrum analyzer. 3. Adjust the spectrum analyzer to have the center frequency the same with the measured carrier. RBW=VBW=1MHz, detector mode is positive peak. Turn off the averaging function and use zero span. 4. The calibrating signal power shall be reduced to 0 dbm and it shall be verified that the power meter reading also reduces by 10 db. 5. Connect the equipment to be measured. Using the following settings of the spectrum analyzer in combination with "max hold" function, find the frequency of highest power output in the power envelope: center frequency equal to operating frequency; RBW & VBW: 1 MHz; detector mode: positive peak; averaging: off; span: 3 times the spectrum width; amplitude: adjust for middle of the instrument's range. The frequency found shall be recorded. 6. Set the center frequency of the spectrum analyzer to the found frequency and switch to zero span. Report Format Version: 01 Page : 10 of 37

14 Report : ER7D1808 The power meter indicates the measured power density (D). The maximum spectral power density e.i.r.p. is calculated from the above measured power density (D), the observed duty cycle factor(x), and the applicable antenna assembly gain "G" in dbi, according to the formula: PD = D + G + 10 log (1/x). 7. The measurement shall be repeated at the lowest, the middle, and the highest channel of the stated frequency range Test Setup Layout Test Deviation There is no deviation with the original standard EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: 01 Page : 11 of 37

15 Report : ER7D Test Result Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations b/g Test Date Jan. 24, 2008 Configuration IEEE b Test Conditions Maximum EIRP Spectral Power Density (dbm / MHz) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Configuration IEEE g Test Conditions Maximum EIRP Spectral Power Density (dbm / MHz) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Report Format Version: 01 Page : 12 of 37

16 Report : ER7D Frequency Range Measurement Limit The frequency range of the equipment is determined by the lowest and highest frequencies occupied by the power envelope. f H is the highest frequency of the power envelope: it is the frequency furthest above the frequency of maximum power where the output power drops below the level of -80 dbm/hz e.i.r.p. spectral power density (-30 dbm if measured in a 100 khz bandwidth). f L is the lowest frequency of the power envelope; it is the frequency furthest below the frequency of maximum power where the output power drops below the level equivalent to -80 dbm/hz e.i.r.p. spectral power density (or -30 dbm if measured in a 100 khz bandwidth). The frequency range is determined by the lowest value of f L and the highest value of f H resulting from the adjustment of the equipment to the lowest and highest operating frequencies. For all equipment, the frequency range shall lie within the band 2.4 GHz to GHz (f L > 2.4 GHz and f H < GHz) Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of Spectrum Analyzer. Spectrum Analyzer Attenuation Span Frequency RB VB Detector Trace Setting 20~30dB 40MHz 100 khz 100 khz Average Average 50 sweeps Test Procedures 1. The transmitter output (antenna port) was connected to the spectrum analyzer. 2. Added [x] dbi of antenna gain was on the spectrum analyzer. 3. Place the spectrum analyzer in detector averaging mode with a minimum of 50 sweeps selected and activate transmitter with modulation applied. 4. Select lowest operating frequency of the equipment under test. 5. Find lowest frequency below the operating frequency at which spectral power density drops below -80 dbm/hz e.i.r.p. (-30 dbm if measured in a 100 khz bandwidth). This frequency shall be recorded (f L ). 6. Select the highest operating frequency of the equipment under test. 7. Find the highest frequency at which the spectral power density drops below-80 dbm/hz e.i.r.p. (-30 dbm if measured in a 100 khz bandwidth). This frequency shall be recorded (f H ). 8. These measurements shall also be performed at normal and extreme test conditions. Report Format Version: 01 Page : 13 of 37

17 Report : ER7D Test Setup Layout Test Deviation There is no deviation with the original standard EUT Operation during Test The EUT was programmed to be in continuously transmitting mode Test Result Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations b/g Test Date Jan. 24, 2008 Configuration IEEE b Test Conditions Frequency range (MHz) f L CH 1 f H CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 55 V max (V) V min (V) V max (V) V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Report Format Version: 01 Page : 14 of 37

18 Report : ER7D1808 Configuration IEEE g Test Conditions Frequency range (MHz) f L CH 1 f H CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 55 V max (V) V min (V) V max (V) V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Report Format Version: 01 Page : 15 of 37

19 Report : ER7D Transmitter Spurious Emissions Measurement Limit Transmitter spurious emissions are emissions outside the frequency range(s) of the equipment as defined in 2.4~2.4835GHz when the equipment is in Transmit mode and/or in Standby mode. The spurious emissions of the transmitter shall not exceed the values in tables 1 and 2 in the indicated bands. Table 1 Transmitter limits for narrowband spurious emissions Frequency Range (MHz) Transmit Mode (dbm) Standby Mode (dbm) 30~ ~ ~1900 / 5150~ Table 2 Transmitter limits for wideband spurious emissions Frequency Range (MHz) Transmit Mode (dbm/hz) Standby Mode (dbm/hz) 30~ ~ ~1900 / 5150~ Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer. Spectrum Analyzer Attenuation Start Frequency Stop Frequency Detector Span Sweep Time RB / VB Setting Auto 30 MHz MHz Positive Peak 100 MHz 1s 100 khz / 30 khz Test Procedures 1. The EUT was placed on the top of the turntable in fully anechoic chamber. 2. The test shall be made in the transmitting mode. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. This measurement shall be repeated with the transmitter in standby mode where applicable. 4. For 30~1000MHz spurious emissions measurement, the broad band bi-log receiving antenna was placed 3 meters far away from the turntable. For 1~12.75GHz measurement, the receiving Horn antenna was placed 1.5 meters far away from the turntable. Report Format Version: 01 Page : 16 of 37

20 Report : ER7D The broadband receiving antenna was fixed on the same height with the EUT to find each suspected emissions of both horizontal and vertical polarization. Each recorded suspected value is indicated as Read Level (Raw). 6. Replace the EUT by standard antenna and feed the RF port by signal generator. 7. Adjust the frequency of the signal generator to the suspected emission and slightly rotate the turntable to locate the position with maximum reading. 8. Adjust the power level of the signal generator to reach the same reading with Read Level (Raw). 9. The level of the spurious emission is the power level of (8) plus the gain of the standard antenna in dbi and minus the loss of the cable used between the signal generator and the standard antenna. 10. If the level calculated in (9) is higher than limit by more than 6dB, then lower the RBW of the spectrum analyzer to 30KHz. If the level of this emission does not change by more than 2dB, then it is taken as narrowband emission, otherwise, wideband emission. 11. The measurement shall be repeated at the lowest and the highest channel of the stated frequency range Test Setup Layout Report Format Version: 01 Page : 17 of 37

21 Report : ER7D Test Deviation There is no deviation with the original standard EUT Operation during Test The EUT was programmed to be in continuously transmitting mode Results of Standby Mode Spurious Emissions In the initial investigation on standby mode and receiving mode, no significant differences in spurious emissions were observed between these 2 modes. Therefore, test data for standby mode was omitted in this section Results of Transmitter Spurious Emissions Below 1GHz Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations g / CH 13 Horizontal Report Format Version: 01 Page : 18 of 37

22 Report : ER7D1808 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 01 Page : 19 of 37

23 Report : ER7D Results of Transmitter Spurious Emissions Above 1GHz Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations b / CH 1 Horizontal Report Format Version: 01 Page : 20 of 37

24 Report : ER7D1808 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 01 Page : 21 of 37

25 Report : ER7D1808 Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations b / CH 13 Horizontal Report Format Version: 01 Page : 22 of 37

26 Report : ER7D1808 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 01 Page : 23 of 37

27 Report : ER7D1808 Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations g / CH 1 Horizontal Report Format Version: 01 Page : 24 of 37

28 Report : ER7D1808 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 01 Page : 25 of 37

29 Report : ER7D1808 Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations g / CH 13 Horizontal Report Format Version: 01 Page : 26 of 37

30 Report : ER7D1808 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 01 Page : 27 of 37

31 Report : ER7D Receiver Spurious Emissions Measurement Limit Receiver spurious emissions are emissions at any frequency when the equipment is in received mode. The spurious emissions of the reviver shall not exceed the values in tables 1 and 2 in the indicated bands. Table 1 Receiver limits for narrowband spurious emissions Frequency Range (MHz) Limit (dbm) 30~ ~ Table 2 Receiver limits for wideband spurious emissions Frequency Range (MHz) Limit (dbm) 30~ ~ Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer. Spectrum Analyzer Attenuation Start Frequency Stop Frequency Detector Span Sweep Time RB / VB Setting Auto 30 MHz MHz Positive Peak 100 MHz 1s 100 khz / 30 khz Test Procedures 1. The EUT was placed on the top of the turntable in fully anechoic chamber. 2. The test shall be made in the transmitting mode. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. For 30~1000MHz spurious emissions measurement, the broad band bi-log receiving antenna was placed 3 meters far away from the turntable. For 1~12.75GHz measurement, the receiving Horn antenna was placed 1.5 meters far away from the turntable. 4. The broadband receiving antenna was fixed on the same height with the EUT to find each suspected emissions of both horizontal and vertical polarization. Each recorded suspected value is indicated as Read Level (Raw). 5. Replace the EUT by standard antenna and feed the RF port by signal generator. 6. Adjust the frequency of the signal generator to the suspected emission and slightly rotate the Report Format Version: 01 Page : 28 of 37

32 Report : ER7D1808 turntable to locate the position with maximum reading. 7. Adjust the power level of the signal generator to reach the same reading with Read Level (Raw). 8. The level of the spurious emission is the power level of (7) plus the gain of the standard antenna in dbi and minus the loss of the cable used between the signal generator and the standard antenna. 9. The measurement shall be repeated at the lowest and the highest channel of the stated frequency range Test Setup Layout Test Deviation There is no deviation with the original standard EUT Operation during Test The EUT was programmed to be in continuously receiving mode. Report Format Version: 01 Page : 29 of 37

33 Report : ER7D Results of Receiver Spurious Emissions Below 1GHz Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations g / CH 13 Horizontal Report Format Version: 01 Page : 30 of 37

34 Report : ER7D1808 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 01 Page : 31 of 37

35 Report : ER7D Results of Receiver Spurious Emissions Above 1GHz Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations b / CH 1 Horizontal Report Format Version: 01 Page : 32 of 37

36 Report : ER7D1808 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 01 Page : 33 of 37

37 Report : ER7D1808 Temperature 26 Humidity 56% Test Engineer Roy Huang Configurations g / CH 13 Horizontal Report Format Version: 01 Page : 34 of 37

38 Report : ER7D1808 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 01 Page : 35 of 37

39 Report : ER7D LIST OF MEASURING EQUIPMENTS Instrument Manufacturer Model Serial Characteristics Calibration Date Spectrum analyzer R&S FSEK kHz ~ 30GHz Oct. 03, 2007 Amplifier ADVANTEST BB525C CH kHz ~ 3GHz Dec. 13, 2007 Amplifier Agilent 8449B 3008A GHz ~ 26.5GHz Mar. 07, 2007 Amplifier COM-POWER PA MHz~1MHz Jul. 26, 2007 Bilog Antenna SCHAFFNER CBL6111C MHz ~ 2GHz Jul. 19, 2007 Horn Antenna COM-POWER AH GHz ~ 18GHz Dec. 20, 2007 Horn Antenna COM-POWER AH GHz ~ 18GHz Jul. 30, 2007 Signal Generator R&S SMR MHz ~ 40GHz Mar. 07, 2007 RF Cable-R03m Jye Bao RG142 CB031 30MHz ~1GHz Oct. 01, 2007 RF Cable-HIGH SUHNER SUCOFLEX CH01-HY 1GHz~26.5GHz Jan. 03, 2008 Horn Antenna SCHWARZBECK BBHA9170 BBHA GHz ~ 40GHz Jan. 18, 2008 Horn Antenna SCHWARZBECK BBHA9170 BBHA GHz ~ 40GHz Jan. 16, 2008 Amplifier MITEQ AMF-6F GHz - 40 GHz Jan. 22, 2007* Turn Table HD DS /655/ degree N/A Antenna Mast HD MA /569/12 1 m ~ 4 m N/A Spectrum Analyzer R&S FSP kHz ~ 30GHz Jan. 10, 2008 Power Meter R&S NRVS DC ~ 40GHz Jun. 27, 2007 Power Sensor R&S NRV-Z DC ~ 30GHz Jun. 27, 2007 Power Sensor R&S NRV-Z MHz ~ 6GHz Jun. 27, 2007 AC Power Source HPC HPA-500W HPA AC 0 ~ 300V May 04, 2007* DC Power Source G.W. GPC-6030D C DC 1V ~ 60V Mar. 03, 2007 Temp. and Humidity Chamber KSON THS-C3L 612 N/A Jan. 14, 2008 RF CABLE-1m Jye Bao RG142 CB034-1m 20MHz ~ 7GHz Jan. 04, 2008 RF CABLE-2m Jye Bao RG142 CB035-2m 20MHz ~ 1GHz Jan. 04, 2008 Vector Signal Generator R&S SMU200A kHz ~ 6GHz Nov. 14, 2007 Signal Generator R&S SMR MHz ~ 40GHz Mar. 07, 2007 Note: Calibration Interval of instruments listed above is one year. Note: * Calibration Interval of instruments listed above is two year. Remark Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Report Format Version: 01 Page : 36 of 37

40 Report : ER7D TEST LOCATION SHIJR ADD : 6Fl., 106, Sec. 1, Shintai 5th Rd., Shijr City, Taipei, Taiwan 221, R.O.C. TEL : FAX : HWA YA ADD : 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. TEL : FAX : LINKOU ADD : 30-2, Dingfu Tsuen, Linkou Shiang, Taipei, Taiwan 244, R.O.C TEL : FAX : DUNGHU ADD : 3, Lane 238, Kangle St., Neihu Chiu, Taipei, Taiwan 114, R.O.C. TEL : FAX : JUNGHE ADD : 7Fl., 758, Jungjeng Rd., Junghe City, Taipei, Taiwan 235, R.O.C. TEL : FAX : NEIHU ADD : 4Fl., 339, Hsin Hu 2 nd Rd., Taipei 114, Taiwan, R.O.C. TEL : FAX : JHUBEI ADD : 8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. TEL : FAX : Report Format Version: 01 Page : 37 of 37

41 APPENDIX A. Photographs of EUT SPORTON International Inc. PAGE NUMBER : A1 OF A7 TEL : ISSUED DATE : FAX :

42 SPORTON International Inc. PAGE NUMBER : A2 OF A7 TEL : ISSUED DATE : FAX :

43 SPORTON International Inc. PAGE NUMBER : A3 OF A7 TEL : ISSUED DATE : FAX :

44 SPORTON International Inc. PAGE NUMBER : A4 OF A7 TEL : ISSUED DATE : FAX :

45 SPORTON International Inc. PAGE NUMBER : A5 OF A7 TEL : ISSUED DATE : FAX :

46 SPORTON International Inc. PAGE NUMBER : A6 OF A7 TEL : ISSUED DATE : FAX :

47 SPORTON International Inc. PAGE NUMBER : A7 OF A7 TEL : ISSUED DATE : FAX :

48 Report : ER7D1808 Appendix B. Test Photos Page : B1 of B3

49 Report : ER7D Photographs of Radiated Emissions Test Configuration FRONT VIEW REAR VIEW Page : B2 of B3

50 Report : ER7D1808 SIDE VIEW Page : B3 of B3