CE Test Report. Approved & Reviewed by: Ty: XXX. Gary Chang / Manager. Report No.: ER AN Page : 1 of 97 Report Version: Rev.

Transcription

1 CE Test Report Equipment Model No. Brand Name Applicant : Radio Module : SSD45N : Laird Technologies : Laird Technologies Address : Thompson Ave. / Lenexa, Kansas / / USA Standard : EN V1.8.1 ( ) Received Date : Jan. 20, 2016 Tested Date : Jan. 20 ~ Jan. 25, 2016 We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Approved & Reviewed by: Gary Chang / Manager Ty: XXX Report No.: ER AN Page : 1 of 97

2 Table of Contents 1 GENERAL DESCRIPTION Information Local Support Equipment List Test Setup Chart Test Equipment and Calibration Data Testing Applied Standards Measurement Uncertainty TEST CONFIGURATION Testing Condition The Worst Test Modes and Channel Details TRANSMITTER TEST RESULTS Carrier Frequencies Occupied Channel Bandwidth RF Output Power, Transmit Power Control (TPC) and Power density Transmitter Unwanted Emissions outside the 5 GHz RLAN Bands Transmitter Unwanted Emissions within the 5 GHz RLAN Band RECEIVER TEST RESULTS Receiver Spurious Emissions ADAPTIVITY TEST RESULTS Adaptivity PHOTOGRAPHS OF THE TEST CONFIGURATION TEST LABORATORY INFORMATION Report No.: ER AN Page : 2 of 97

3 Release Record Report No. Version Description Issued Date ER AN Rev. 01 Initial issue Feb. 15, 2016 Report No.: ER AN Page : 3 of 97

4 Summary of Test Result Ref. Std. Clause Test Items Measured Result 4.2 Centre Frequencies Meet the requirement of limit. Pass Nominal Channel Bandwidth and Occupied Channel Bandwidth RF Output Power & Transmit Power Control (TPC) Meet the requirement of limit GHz: dbm GHz: dbm Pass Pass 4.4 Power Density Meet the requirement of limit. Pass 4.5 Transmitter Unwanted Emissions Meet the requirement of limit. Pass 4.6 Receiver Spurious Emissions Meet the requirement of limit. Pass 4.7 Dynamic Frequency Selection (DFS) Meet the requirement of limit. Pass 4.8 Adaptivity (Channel Access Mechanism) Meet the requirement of limit. Pass 4.10 Geo-location capability NOTE: The DFS measurement was recorded in Report No.: EY This test is not required since the device does not support this function NA Report No.: ER AN Page : 4 of 97

5 1 General Description 1.1 Information This report is issued as a supplementary report to the original ICC report no. ER442904AN. The modification is updating standard from V1.7.1 to V All tests had been done and presented in the following sections Specification of the Equipment under Test (EUT) IEEE Std a n (HT20) Frequency Range (MHz) RF General Information Ch. Freq. (MHz) Channel Number [4] [4] [11] [4] [4] [11] Transmit Chains (N TX ) Data Rate / MCS Mbps 1 MCS 0-7 Note 1: a/n uses a combination of OFDM-BPSK, QPSK, 16QAM, 64QAM modulation Antenna Details Ant. No Brand / Model Type Connector MAG.LAYERS EDA GR2 -B2-CY MAG.LAYERS PCA G4C1 -A13-CY Larid NanoBlade-IP04 Larid MAF95310 Mini NanoBlade Flex Laird NanoBlue-IP04 Ethertronics WLAN_ Dipole SMA Jack Reverse Operating Frequencies (MHz) / Antenna Gain (dbi) 2400~ ~ ~ ~ PCB Dipole UFL PCB Dipole UFL PCB Dipole UFL PCB Dipole UFL PIFA UFL Report No.: ER AN Page : 5 of 97

6 1.1.3 EUT Operational Condition Power Supply Type 3.3Vdc from host Operational Voltage Vnom (3.30 V) Vmax (3.40 V) Vmin (3.20 V) Operational Climatic Tnom (20 C) Tmax (70 C) Tmin (-20 C) Accessories N/A Adaptive Equipment Adaptive Equipment Adaptive Equipment without the possibility to switch to a non-adaptive mode: The equipment has implemented an LBT based DAA mechanism: The equipment is Frame Based equipment The equipment is Load Based equipment The equipment can switch dynamically between Frame Based and Load Based equipment The equipment has implemented an non-lbt based DAA mechanism The equipment can operate in more than one adaptive mode Adaptive Equipment which can also operate in a non-adaptive mode Report No.: ER AN Page : 6 of 97

7 1.1.6 Channel List Frequency band (MHz) a / n HT20 Channel Frequency(MHz) Test Tool and Duty Cycle Test tool Duty Cycle Of Test Signal (%) Duty Factor ART, version: rev0.2 build# % - IEEE a 99.25% - IEEE n (HT20) IEEE a IEEE n (HT20) Report No.: ER AN Page : 7 of 97

8 1.1.8 Power Setting Test Frequency (MHz) Modulation Mode a / HT a n (HT20) Local Support Equipment List Support Equipment List No. Equipment Brand Model S/N FCC ID Signal cable / Length (m) 1 Notebook DELL Latitude E6440 2ZC4Z52 DoC Test Setup Chart Test Setup Diagram (Adapter mode) Report No.: ER AN Page : 8 of 97

9 1.4 Test Equipment and Calibration Data Test Item Test Site RF Conducted (TH01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Spectrum Analyzer ROHDE&SCHWARZ FSV Oct. 14, 2015 Oct. 13, 2016 TEMP&HUMIDITY CHAMBER GIANT FORCE GCT SP-SD MAF Nov. 27, 2015 Nov. 26, 2016 Power Meter Anritsu ML2495A Sep. 21, 2015 Sep. 20, 2016 Power Sensor Anritsu MA2411B Sep. 21, 2015 Sep. 20, 2016 DC POWER SOURCE Measurement Software Measurement Software GW INSTEK GPC-3060D EM Oct. 20, 2015 Oct. 19, 2016 Sporton Sporton_ NA NA Agilent EN RF test NA NA Note: Calibration Interval of instruments listed above is one year. Test Item Test Site Radiated Emissions Fully-anechoic chamber 1 / (05CH01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Spectrum Analyzer Agilent N9010A MY Aug. 24, 2015 Aug. 23, 2016 Bilog Antenna SCHWARZBECK VULB9168 VULB Oct. 03, 2015 Oct. 02, 2016 Horn Antenna 1G-18G Horn Antenna 18G-40G SCHWARZBECK BBHA 9120 D BBHA 9120 D 1094 Oct. 20, 2015 Oct. 19, 2016 SCHWARZBECK BBHA 9170 BBHA Jan. 04, 2016 Jan. 03, 2017 Preamplifier Agilent 83017A MY Dec. 11, 2015 Dec. 10, 2016 Preamplifier EMC EMC Oct. 14, 2015 Oct. 13, 2016 Preamplifier EMC EMC184045B Sep. 01, 2015 Aug. 31, 2016 RF Cable HUBER+SUHNER SUCOFLEX104 MY16609/4 Dec. 04, 2015 Dec. 03, 2016 RF Cable HUBER+SUHNER SUCOFLEX104 MY16608/4 Dec. 04, 2015 Dec. 03, 2016 RF Cable HUBER+SUHNER SUCOFLEX104 MY16617/4 Dec. 04, 2015 Dec. 03, 2016 LF cable 3M Woken CFD400NL-LW CFD400NL-005 Dec. 04, 2015 Dec. 03, 2016 LF cable 10M Woken CFD400NL-LW CFD400NL-006 Dec. 04, 2015 Dec. 03, 2016 Measurement Software AUDIX e g NA NA Note: Calibration Interval of instruments listed above is one year. Report No.: ER AN Page : 9 of 97

10 Test Item Test Site RF Conducted (DF01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Spectrum R&S FSV Dec. 10, 2015 Dec. 09, 2016 Spectrum Keysight N9010A MY May. 18, 2015 May. 17, 2016 Signal Generator R&S SMB100A Oct. 05, 2015 Oct. 04, 2016 RF cable-4m HUBER+SUHNER SUCOFLEX_104 MY15686/4 Dec. 17, 2015 Dec. 16, 2016 RF cable-0.5m HUBER+SUHNER SUCOFLEX_ /4 Dec. 17, 2015 Dec. 16, 2016 RF cable-0.2m HUBER+SUHNER SUCOFLEX_ /4 Dec. 17, 2015 Dec. 16, 2016 RF cable-0.2m HUBER+SUHNER SUCOFLEX_ /4 Dec. 17, 2015 Dec. 16, 2016 MXG-B RF Vector Signal Generator Agilent N5182B MY Mar. 30, 2015 Mar. 29, 2016 Preamplifier EMC EMC Oct. 14, 2015 Oct. 13, 2016 Oscilloscope National Instruments USB-5133 F651FF Jun. 15, 2015 Jun. 14, 2016 Measurement Software Sporton Sporton_ NA NA Note: Calibration Interval of instruments listed above is one year. 1.5 Testing Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: EN V1.8.1 ( ) 1.6 Measurement Uncertainty ISO/IEC requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2) Measurement Uncertainty Parameters Uncertainty Limit Radio Frequency ±1.4 x 10-9 ± RF power conducted ±0.808 db ±1,5 db RF power radiated ±3.398 db ±6 db Spurious emission, conducted ±2.470 db ±3 db Spurious emission, radiated ±3.398 db ±6 db Humidity ±4.7% ±5 % Temperature ±0.8 o C ±1 C Time ±0.1 % ±10 % Report No.: ER AN Page : 10 of 97

11 2 Test Configuration 2.1 Testing Condition Test Item Test Site Ambient Condition Tested By RF Conducted TH01-WS 23 C / 63% Ryan Lee Radiated Emission 05CH01-WS 19 C / 70% Ryan Lee Adaptivity DF01-WS 24 C / 63% Ryan Lee 2.2 The Worst Test Modes and Channel Details Test item Modulation Mode Test Frequency (MHz) Data Rate Centre Frequencies RF Output Power Power Spectral Density 11a HT / 5320 / 5500 / / 5320 / 5500 / , 2, 3 Occupied Channel Bandwidth Transmitter Unwanted Emissions within the 5 GHz RLAN Band Transmitter Unwanted Emissions outside the 5 GHz RLAN Bands (below 1GHz test) Transmitter Unwanted Emissions outside the 5 GHz RLAN Bands (above 1GHz test) Receiver Spurious Emissions 11a HT20 11a HT20 11a HT20 11a HT20 11a HT / 5320 / 5500 / / 5320 / 5500 / / / / 5320 / 5500 / / 5320 / 5500 / / 5320 / 5500 / / 5320 / 5500 / / / 5700 Adaptivity HT / NOTE: 1 1 Note 2 Note 2 Note types antenna are used for this device, highest gain antenna of each type is selected to perform radiated emission test as below test configuration. 1) Configuration 1 : Dipole antenna (Antenna No.1) 2) Configuration 2 : PCB Dipole antenna (Antenna No.3) 3) Configuration 3 : PIFA antenna (Antenna No.6) 2. Conducted and radiated emissions are measured. A 50 Ω terminator is connected to antenna port of EUT for radiated emission measurement. Report No.: ER AN Page : 11 of 97

12 3 Transmitter Test Results 3.1 Carrier Frequencies Limit of Carrier Frequencies The actual centre frequency for any given channel declared by the manufacturer shall be maintained within the range f c ± 20 ppm Test Procedures Reference to clause of ETSI EN V1.8.1 ( ) Test Setup Report No.: ER AN Page : 12 of 97

13 3.1.4 Test Result of Carrier Frequencies Test Configuration 1 Carrier Centre Frequencies (ppm) Condition Modulation Mode Freq. (MHz) Freqeuncy (MHz) Carrier Stability Limit (ppm) T nom V nom a T min V max a T min V min a T max V max a T max V min a T nom V nom a T min V max a T min V min a T max V max a T max V min a T nom V nom a T min V max a T min V min a T max V max a T max V min a T nom V nom a T min V max a T min V min a T max V max a T max V min a Report No.: ER AN Page : 13 of 97

14 Test Configuration 1 Carrier Centre Frequencies (ppm) Condition Modulation Mode Freq. (MHz) Freqeuncy (MHz) Carrier Stability Limit (ppm) T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT Report No.: ER AN Page : 14 of 97

15 Test Configuration 2 Carrier Centre Frequencies (ppm) Condition Modulation Mode Freq. (MHz) Freqeuncy (MHz) Carrier Stability Limit (ppm) T nom V nom a T min V max a T min V min a T max V max a T max V min a T nom V nom a T min V max a T min V min a T max V max a T max V min a T nom V nom a T min V max a T min V min a T max V max a T max V min a T nom V nom a T min V max a T min V min a T max V max a T max V min a Report No.: ER AN Page : 15 of 97

16 Test Configuration 2 Carrier Centre Frequencies (ppm) Condition Modulation Mode Freq. (MHz) Freqeuncy (MHz) Carrier Stability Limit (ppm) T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT Report No.: ER AN Page : 16 of 97

17 Test Configuration 3 Carrier Centre Frequencies (ppm) Condition Modulation Mode Freq. (MHz) Freqeuncy (MHz) Carrier Stability Limit (ppm) T nom V nom a T min V max a T min V min a T max V max a T max V min a T nom V nom a T min V max a T min V min a T max V max a T max V min a T nom V nom a T min V max a T min V min a T max V max a T max V min a T nom V nom a T min V max a T min V min a T max V max a T max V min a Report No.: ER AN Page : 17 of 97

18 Test Configuration 3 Carrier Centre Frequencies (ppm) Condition Modulation Mode Freq. (MHz) Freqeuncy (MHz) Carrier Stability Limit (ppm) T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT T nom V nom n HT T min V max n HT T min V min n HT T max V max n HT T max V min n HT Report No.: ER AN Page : 18 of 97

19 3.2 Occupied Channel Bandwidth Limit of Occupied Channel Bandwidth The Nominal Channel Bandwidth shall be at least 5 MHz at all times. The Occupied Channel Bandwidth shall be between 80 % and 100 % of the declared Nominal Channel Bandwidth. In case of smart antenna systems (devices with multiple transmit chains) each of the transmit chains shall meet this requirement Test Procedures Reference to clause of ETSI EN V1.8.1 ( ) Test Setup Test Result of Occupied Channel Bandwidth Test Configuration 1 Modulation Mode Frequency (MHz) Occupied Channel Bandwidth (MHz) Occupied Channel Bandwidth Limit (MHz) a a a a n HT n HT n HT n HT Report No.: ER AN Page : 19 of 97

20 3.3 RF Output Power, Transmit Power Control (TPC) and Power density Limit of RF Output Power, Transmit Power Control (TPC) and Power density E.I.R.P limits for RF output power and power density at the highest power level Frequency range (MHz) Mean e.i.r.p. limit [dbm] Mean e.i.r.p. density limit [dbm/mhz] With TPC Without TPC With TPC Without TPC 5150 to / 23 (see note 1) 10 7 / 10 (see note 2) 5470 to (see note 3) 27 (see note 3) 17 (see note 3) 14 (see note 3) Note 1: The applicable limit is 20 dbm, except for transmissions whose nominal bandwidth falls completely within the band 5150 MHz to 5250 MHz, in which case the applicable limit is 23 dbm. Note 2: The applicable limit is 7 dbm/mhz except for transmissions whose nominal bandwidth falls completely within the band 5150 MHz to 5250 MHz, in which case the applicable limit is 10 dbm/mhz. Note 3: Slave devices without a Radar Interference Detection function shall comply with the limits for the band 5250 MHz to 5350 MHz. E.I.R.P limits for RF output power at the lowest power level Frequency range (MHz) Mean e.i.r.p. [dbm] 5250 to to (see note) Note: Slave devices without a Radar Interference Detection function shall comply with the limits for the band 5250 MHz to 5350 MHz Test Procedures Reference to clause of ETSI EN V1.8.1 ( ). Report No.: ER AN Page : 20 of 97

21 3.3.3 Test Setup For RF Output Power, Transmit Power Control (TPC) For Power Density Report No.: ER AN Page : 21 of 97

22 3.3.4 Test Result of RF Output Power at the Highest Power Test Configuration 1 Maximum Transmit Power (dbm) Condition Freq. (MHz) a Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 22 of 97

23 Test Configuration 1 Maximum Transmit Power (dbm) Condition Freq. (MHz) n HT20 Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 23 of 97

24 Test Configuration 2 Maximum Transmit Power (dbm) Condition Freq. (MHz) a Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 24 of 97

25 Test Configuration 2 Maximum Transmit Power (dbm) Condition Freq. (MHz) n HT20 Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 25 of 97

26 Test Configuration 3 Maximum Transmit Power (dbm) Condition Freq. (MHz) a Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 26 of 97

27 Test Configuration 3 Maximum Transmit Power (dbm) Condition Freq. (MHz) n HT20 Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 27 of 97

28 3.3.5 Test Result of RF Output Power at the Lowest Power Test Configuration 1 Maximum Transmit Power (dbm) Condition Freq. (MHz) a Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 28 of 97

29 Test Configuration 1 Maximum Transmit Power (dbm) Condition Freq. (MHz) n HT20 Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 29 of 97

30 Test Configuration 2 Maximum Transmit Power (dbm) Condition Freq. (MHz) a Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 30 of 97

31 Test Configuration 2 Maximum Transmit Power (dbm) Condition Freq. (MHz) n HT20 Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 31 of 97

32 Test Configuration 3 Maximum Transmit Power (dbm) Condition Freq. (MHz) a Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 32 of 97

33 Test Configuration 3 Maximum Transmit Power (dbm) Condition Freq. (MHz) n HT20 Limit (dbm) T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min T nom V nom T min V max T min V min T max V max T max V min Report No.: ER AN Page : 33 of 97

34 3.3.6 Test Result of Power Density Test Configuration 1 Modulation Mode Freq. (MHz) Power Density (dbm/1mhz) e.i.r.p. Limit (dbm/1mhz) e.i.r.p. Results a Pass a Pass a Pass a Pass n HT Pass n HT Pass n HT Pass n HT Pass Test Configuration 2 Modulation Mode Freq. (MHz) Power Density (dbm/1mhz) e.i.r.p. Limit (dbm/1mhz) e.i.r.p. Results a Pass a Pass a Pass a Pass n HT Pass n HT Pass n HT Pass n HT Pass Test Configuration 3 Modulation Mode Report No.: ER AN Page : 34 of 97 Freq. (MHz) Power Density (dbm/1mhz) e.i.r.p. Limit (dbm/1mhz) e.i.r.p. Results a Pass a Pass a Pass a Pass n HT Pass n HT Pass n HT Pass n HT Pass

35 3.4 Transmitter Unwanted Emissions outside the 5 GHz RLAN Bands Limit of Transmitter Unwanted Emissions outside the 5 GHz RLAN Bands Frequency Range Maximum Power Bandwidth 30 MHz to 47 MHz -36 dbm 100 khz 47 MHz to 74 MHz -54 dbm 100 khz 74 MHz to 87,5 MHz -36 dbm 100 khz 87,5 MHz to 118 MHz -54 dbm 100 khz 118 MHz to 174 MHz -36 dbm 100 khz 174 MHz to 230 MHz -54 dbm 100 khz 230 MHz to 470 MHz -36 dbm 100 khz 470 MHz to 862 MHz -54 dbm 100 khz 862 MHz to 1 GHz -36 dbm 100 khz 1 GHz to 5,15 GHz -30 dbm 1 MHz 5,35 GHz to 5,47 GHz -30 dbm 1 MHz 5,725 GHz to 26 GHz -30 dbm 1 MHz Test Procedures Reference to clause of ETSI EN V1.8.1 ( ). Report No.: ER AN Page : 35 of 97

36 3.4.3 Test Setup For Radiated Test Below 1GHz Above 1 GHz For Conducted Test Report No.: ER AN Page : 36 of 97

37 3.4.4 Radiated Results of Transmitter Spurious Emissions (Below 1GHz) Modulation 11a Test Freq. (MHz) 5180 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 37 of 97

38 Modulation 11a Test Freq. (MHz) 5180 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 38 of 97

39 Modulation 11a Test Freq. (MHz) 5700 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 39 of 97

40 Modulation 11a Test Freq. (MHz) 5700 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 40 of 97

41 Modulation HT20 Test Freq. (MHz) 5180 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 41 of 97

42 Modulation HT20 Test Freq. (MHz) 5180 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 42 of 97

43 Modulation HT20 Test Freq. (MHz) 5700 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 43 of 97

44 Modulation HT20 Test Freq. (MHz) 5700 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 44 of 97

45 3.4.5 Radiated Results of Transmitter Radiated Unwanted Emissions (Above 1GHz) Modulation 11a Test Freq. (MHz) 5180 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 45 of 97

46 Modulation 11a Test Freq. (MHz) 5180 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 46 of 97

47 Modulation 11a Test Freq. (MHz) 5700 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 47 of 97

48 Modulation 11a Test Freq. (MHz) 5700 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 48 of 97

49 Modulation HT20 Test Freq. (MHz) 5180 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 49 of 97

50 Modulation HT20 Test Freq. (MHz) 5180 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 50 of 97

51 Modulation HT20 Test Freq. (MHz) 5700 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 51 of 97

52 Modulation HT20 Test Freq. (MHz) 5700 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 52 of 97

53 3.4.6 Conducted Results of Transmitter Spurious Emissions (Below 1GHz) Modulation 11a Test Freq. (MHz) 5180 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 53 of 97

54 Modulation 11a Test Freq. (MHz) 5700 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 54 of 97

55 Modulation HT20 Test Freq. (MHz) 5180 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 55 of 97

56 Modulation HT20 Test Freq. (MHz) 5700 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 56 of 97

57 3.4.7 Conducted Results of Transmitter Spurious Emissions (Above 1GHz) Modulation 11a Test Freq. (MHz) 5180 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 57 of 97

58 Modulation 11a Test Freq. (MHz) 5700 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 58 of 97

59 Modulation HT20 Test Freq. (MHz) 5180 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 59 of 97

60 Modulation HT20 Test Freq. (MHz) 5700 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 60 of 97

61 Transmitter Unwanted Emissions within the 5 GHz RLAN Band Limit of Transmitter Unwanted Emissions within the 5 GHz RLAN Band Test Procedures Reference to clause of ETSI EN V1.8.1 ( ) Test Setup Report No.: ER AN Page : 61 of 97

62 3.5.4 Test Result of Transmitter Unwanted Emissions within the 5 GHz RLAN Band for a 5180MHz 5180MHz 5320MHz 5320MHz 5500MHz 5500MHz 5700MHz 5700MHz Report No.: ER AN Page : 62 of 97

63 3.5.5 Test Result of Transmitter Unwanted Emissions within the 5 GHz RLAN Band for n HT MHz 5180MHz 5320MHz 5320MHz 5500MHz 5500MHz 5700MHz 5700MHz Report No.: ER AN Page : 63 of 97

64 4 Receiver Test Results 4.1 Receiver Spurious Emissions Limit of Receiver Spurious Emissions Frequency Range Maximum power Measurement bandwidth 30 MHz to 1 GHz -57 dbm 100kHz 1 GHz to 26 GHz -47 dbm 1MHz Test Procedures Reference to clause of ETSI EN V1.8.1 ( ). Report No.: ER AN Page : 64 of 97

65 4.1.3 Test Setup For Radiated Test Below 1GHz Above 1 GHz For Conducted Test Report No.: ER AN Page : 65 of 97

66 4.1.4 Radiated Results of Receiver Spurious Emissions (Below 1GHz) Modulation 11a Test Freq. (MHz) 5180 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 66 of 97

67 Modulation 11a Test Freq. (MHz) 5180 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 67 of 97

68 Modulation 11a Test Freq. (MHz) 5700 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 68 of 97

69 Modulation 11a Test Freq. (MHz) 5700 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 69 of 97

70 Modulation HT20 Test Freq. (MHz) 5180 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 70 of 97

71 Modulation HT20 Test Freq. (MHz) 5180 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 71 of 97

72 Modulation HT20 Test Freq. (MHz) 5700 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 72 of 97

73 Modulation HT20 Test Freq. (MHz) 5700 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 73 of 97

74 4.1.5 Radiated Results of Receiver Spurious Emissions (Above 1GHz) Modulation 11a Test Freq. (MHz) 5180 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 74 of 97

75 Modulation 11a Test Freq. (MHz) 5180 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 75 of 97

76 Modulation 11a Test Freq. (MHz) 5700 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 76 of 97

77 Modulation 11a Test Freq. (MHz) 5700 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 77 of 97

78 Modulation HT20 Test Freq. (MHz) 5180 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 78 of 97

79 Modulation HT20 Test Freq. (MHz) 5180 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 79 of 97

80 Modulation HT20 Test Freq. (MHz) 5700 Polarization Horizontal Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 80 of 97

81 Modulation HT20 Test Freq. (MHz) 5700 Polarization Vertical Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 81 of 97

82 4.1.6 Conducted Results of Receiver Spurious Emissions (Below 1GHz) Modulation 11a Test Freq. (MHz) 5180 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 82 of 97

83 Modulation 11a Test Freq. (MHz) 5700 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 83 of 97

84 Modulation HT20 Test Freq. (MHz) 5180 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 84 of 97

85 Modulation HT20 Test Freq. (MHz) 5700 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 85 of 97

86 4.1.7 Conducted Results of Receiver Spurious Emissions (Above 1GHz) Modulation 11a Test Freq. (MHz) 5180 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 86 of 97

87 Modulation 11a Test Freq. (MHz) 5700 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 87 of 97

88 Modulation HT20 Test Freq. (MHz) 5180 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 88 of 97

89 Modulation HT20 Test Freq. (MHz) 5700 Note 1: Measured Value (dbm) = Reading (dbm) + Factor (db) Note 2: Margin (db) = Measured Value (dbm) Limit (dbm) Report No.: ER AN Page : 89 of 97

90 5 Adaptivity Test Results 5.1 Adaptivity Adaptivity Limit Adaptivity Limit LBT based Detect and Avoid (Frame Based Equipment): Clear Channel Assessment (CCA) time shall be not less than 20 us; Channel Occupancy Time (COT) shall be in the range 1 ms ~ 10 ms Minimum Idle Period shall be at least 5 % of Channel Occupancy Time Load based Equipment may implement an LBT based spectrum sharing mechanism based on the Clear Channel Assessment (CCA) mode using "energy detect", as described in IEEE [8], clause 9, clause 10, clause 18 and clause 20 or as described in IEEE ac [9], clause 8, clause 9, clause 10 and clause 22 LBT based Detect and Avoid (Load Based Equipment): Option A Clear Channel Assessment (CCA) time shall be not less than 20 us Extended CCA(q * observed slots) observed slot: 18us (ECCA time slot)or Busy slot q=16~1024 / N=1~q Channel Occupancy Time (COT) shall be less than 10 ms Idle Period is equal to CCA or ECCA Option B Clear Channel Assessment (CCA) time shall be not less than 20 us Extended CCA: N*CCA N:1~q randomly / q=4~32 ( q is selected by the manufacturer) Channel Occupancy Time (COT) (13/32*q )ms Idle Period is equal to CCA~CCA*N Short Control Signalling Transmissions: Short Control Signalling Transmissions shall have a maximum duty cycle of 5 % within an observation period of 50 ms Test Procedures Reference to clause of ETSI EN V1.8.1 ( ) Test Setup Report No.: ER AN Page : 90 of 97

91 5.1.4 Test Result of Adaptivity and Short Control Signalling Transmissions Adaptivity Result EUT firmware / software version Adaptivity Detection Threshold Level (dbm) Modulation Mode Freq. (MHz) Short Control Signalling Transmissions (ms) Channel Occupancy Time (ms) Idle Period Time (us) Adaptivity an (HT20) Pass an (HT20) Pass Limit < 2.5 ms - > 20us N/A Report No.: ER AN Page : 91 of 97

92 Adaptivity Result Plots an (HT20) MHz an (HT20) MHz Short Control Signalling Transmissions Plots Short Control Signalling Transmissions Plots an (HT20) MHz an (HT20) MHz Report No.: ER AN Page : 92 of 97

93 Channel Occupancy Time & Idle Period Time an (HT20) MHz Channel Occupancy Time an (HT20) MHz Channel Occupancy Time an (HT20) MHz Idle Period Time an (HT20) MHz Idle Period Time Note: Zoom TX is short control signalling transmission time. Report No.: ER AN Page : 93 of 97

94 6 Photographs of the Test Configuration Spurious Emission Radiated Test Report No.: ER AN Page : 94 of 97

95 Spurious Emission Conducted Test Report No.: ER AN Page : 95 of 97

96 Adaptivity, Receiver Blocking and Short Control Signalling Transmissions Test Report No.: ER AN Page : 96 of 97

97 7 Test laboratory information Established in 2012, ICC provides foremost EMC & RF Testing and advisory consultation services by our skilled engineers and technicians. Our services employ a wide variety of advanced edge test equipment and one of the widest certification extents in the business. International Certification Corp, it is our definitive objective is to institute long term, trust-based associations with our clients. The expectation we set up with our clients is based on outstanding service, practical expertise and devotion to a certified value structure. Our passion is to grant our clients with best EMC / RF services by oriented knowledgeable and accommodating staff. Our Test sites are located at Linkou District and Kwei Shan Hsiang. Location map can be found on our website Linkou Kwei Shan Kwei Shan Site II Tel: Tel: Tel: No. 30-2, Ding Fwu Tsuen, Lin Kou District, New Taipei City, Taiwan, R.O.C. No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. No. 14-1, Lane 19, Wen San 3rd St., Kwei Shan Hsiang, Tao Yuan Hsien 333, Taiwan, R.O.C. If you have any suggestion, please feel free to contact us as below information Tel: Fax: ICC_Service@icertifi.com.tw END Report No.: ER AN Page : 97 of 97