FCC TEST REPORT (15.407)

Transcription

1 FCC TEST REPORT (15.407) REPORT : RF141108C01-1 MODEL : AP 100X FCC ID: 2ACTO-AP100X RECEIVED: Nov. 08, 2014 TESTED: Nov. 19 ~ Nov. 26, 2014 ISSUED: Dec. 02, 2014 APPLICANT: Sophos Ltd ADDRESS: The Pentagon,Abingdon,OX14 3YP,United Kingdom ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF141108C of 78 Report Format Version 5.3.0

2 OF CONTENTS RELEASE CONTROL RECORD CERTIFICATION SUMMARY OF TEST RESULTS MEASUREMENT UNCERTAINTY GENERAL INFORMATION GENERAL DESCRIPTION OF EUT DESCRIPTION OF TEST MODES TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL DUTY CYCLE OF TEST SIGNAL DESCRIPTION OF SUPPORT UNITS CONFIGURATION OF SYSTEM UNDER TEST GENERAL DESCRIPTION OF APPLIED STANDARDS TEST TYPES AND RESULTS RADIATED AND BANDEDGE MEASUREMENT S OF RADIATED AND BANDEDGE MEASUREMENT S OF UNWANTED OUT OF THE RESTRICTED BANDS TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITION TEST RESULTS CONDUCTED MEASUREMENT S OF CONDUCTED MEASUREMENT TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS TRANSMIT POWER MEASUREMENT S OF TRANSMIT POWER MEASUREMENT TEST SETUP TEST INSTRUMENTS TEST PROCEDURE DEVIATION FROM TEST STANDARD EUT OPERATING CONDITIONS TEST RESULTS PEAK POWER SPECTRAL DENSITY MEASUREMENT S OF PEAK POWER SPECTRAL DENSITY MEASUREMENT TEST SETUP TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD EUT OPERATING CONDITIONS TEST RESULTS FREQUENCY STABILITY S OF FREQUENCY STABILITY MEASUREMENT TEST SETUP TEST INSTRUMENTS Report No.: RF141108C of 78 Report Format Version 5.3.0

3 4.5.4 TEST PROCEDURE DEVIATION FROM TEST STANDARD EUT OPERATING CONDITION TEST RESULTS DB BANDWIDTH MEASUREMENT S OF 6DB BANDWIDTH MEASUREMENT TEST SETUP TEST INSTRUMENTS TEST PROCEDURE DEVIATION FROM TEST STANDARD EUT OPERATING CONDITIONS TEST RESULTS PHOTOGRAPHS OF THE TEST CONFIGURATION INFORMATION ON THE TESTING LABORATORIES APPENDIX A MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB Report No.: RF141108C of 78 Report Format Version 5.3.0

4 RELEASE CONTROL RECORD ISSUE REASON FOR CHANGE DATE ISSUED RF141108C01-1 Original release Dec. 02, 2014 Report No.: RF141108C of 78 Report Format Version 5.3.0

5 1. CERTIFICATION PRODUCT: Sophos wireless Access Point AP 100X MODEL: AP 100X BRAND: Sophos APPLICANT: Sophos Ltd TESTED: Nov. 19 ~ Nov. 26, 2014 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart E (Section ) The above equipment (model: AP 100X) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample s EMC characteristics under the conditions specified in this report. PREPARED BY :, DATE : Dec. 02, 2014 Celine Chou / Specialist APPROVED BY :, DATE : Dec. 02, 2014 Ken Liu / Senior Manager Report No.: RF141108C of 78 Report Format Version 5.3.0

6 2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: STANDARD SECTION (b)(6) (b) (1/2/3/4/6) APPLIED STANDARD: FCC PART 15, SUBPART E (SECTION ) TEST TYPE RESULT REMARK AC Power Conducted Emissions Radiated Emissions & Band Edge Measurement PASS PASS Meet the requirement of limit. Minimum passing margin is -5.83dB at MHz. Meet the requirement of limit. Minimum passing margin is -1.0dB at , , , and MHz (a)(1/2/3) Max Average Transmit Power PASS Meet the requirement of limit (a)(1/2/3) Peak Power Spectral Density PASS Meet the requirement of limit (e) 6dB bandwidth PASS Meet the requirement of limit. (U-NII-3 Band only) (g) Frequency Stability PASS Meet the requirement of limit Antenna Requirement PASS Antenna connector is N plug. (The device is professionally installed) 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR : MEASUREMENT FREQUENCY UNCERTAINTY Conducted emissions 9kHz~30MHz 2.44 db Radiated emissions 30MHz ~ 200MHz 200MHz ~1000MHz 1GHz ~ 18GHz 18GHz ~ 40GHz 3.63 db 3.64 db 2.29 db 2.29 db This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. Report No.: RF141108C of 78 Report Format Version 5.3.0

7 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT MODEL POWER SUPPLY MODULATION TYPE MODULATION TECHNOLOGY TRANSFER RATE OPERATING FREQUENCY NUMBER OF CHANNEL OUTPUT POWER TYPE CONNECTOR DATA CABLE I/O PORTS ACCESSORY DEVICES Sophos wireless Access Point AP 100X AP 100X 54Vdc max from POE 256QAM, 64QAM, 16QAM, QPSK, BPSK OFDM a: 54.0/ 48.0/ 36.0/ 24.0/ 18.0/ 12.0/ 9.0/ 6.0Mbps n: up to 450Mbps ac: 1300Mbps 5180 ~ 5240MHz, 5745 ~ 5825MHz 5180 ~ 5240MHz: 4 for a, n (20MHz), ac (20MHz) 2 for n (40MHz), ac (40MHz) 1 for ac (80MHz) 5745 ~ 5825MHz: 5 for a, n (20MHz), ac (20MHz) 2 for n (40MHz), ac (40MHz) 1 for ac (80MHz) 5180 ~ 5240MHz: mW 5745 ~ 5825MHz: mW Dipole antenna with 6dBi gain N Plug 0.95m shielded ground cable without core Refer to user s manual Bracket NOTE: 1. The EUT incorporates a MIMO function. Physically, the EUT provides 3 completed transmitters and 3 receivers. MODULATION MODE TX FUNCTION a 1TX n (20MHz) 3TX n (40MHz) 3TX ac (20MHz) 3TX ac (40MHz) 3TX ac (80MHz) 3TX Report No.: RF141108C of 78 Report Format Version 5.3.0

8 2. The EUT consumes power from the following POE. (provided as support units only) POE BRAND: Power Desine MODEL: PD-9001GR/AC INPUT: Vac, 50-60Hz, 0.67A OUTPUT: 55Vdc, 0.6A 3. The above EUT information is declared by the manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF141108C of 78 Report Format Version 5.3.0

9 3.2 DESCRIPTION OF TEST MODES FOR 5180 ~ 5240MHz 4 channels are provided for a, n (20MHz), ac (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz MHz MHz 2 channels are provided for n (40MHz), ac (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz 1 channel is provided for ac (80MHz): CHANNEL FREQUENCY MHz FOR 5745 ~ 5825MHz 5 channels are provided for a, n (20MHz), ac (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz MHz MHz MHz 2 channels are provided for n (40MHz), ac (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz 1 channel is provided for ac (80MHz): CHANNEL FREQUENCY MHz Report No.: RF141108C of 78 Report Format Version 5.3.0

10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL EUT APPLICABLE TO CONFIGURE DESCRIPTION MODE RE 1G RE<1G PLC APCM - - Where RE 1G: Radiated Emission above 1GHz RE<1G: Radiated Emission below 1GHz PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement NOTE: The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on Y-plane for a and Z-plant for n. RADIATED TEST (ABOVE 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE a BAND AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) 36 to 48 36, 40, 48 OFDM BPSK n (20MHz) 36 to 48 36, 40, 48 OFDM BPSK n (40MHz) 38 to 46 38, 46 OFDM BPSK ac (20MHz) 36 to 48 36, 40, 48 OFDM BPSK ac (40MHz) 38 to 46 38, 46 OFDM BPSK ac (80MHz) OFDM BPSK a 149 to , 157, 165 OFDM BPSK n (20MHz) 149 to , 157, 165 OFDM BPSK n (40MHz) 151 to , 159 OFDM BPSK ac (20MHz) 149 to , 157, 165 OFDM BPSK ac (40MHz) 151 to , 159 OFDM BPSK ac (80MHz) OFDM BPSK 87.8 RADIATED TEST (BELOW 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE a BAND AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) to 48 OFDM BPSK to 165 OFDM BPSK 6.0 Report No.: RF141108C of 78 Report Format Version 5.3.0

11 POWER LINE CONDUCTED TEST: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE a BAND AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) to 48 OFDM BPSK to 165 OFDM BPSK 6.0 PORT CONDUCTED MEASUREMENT: This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE a BAND AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) 36 to 48 36, 40, 48 OFDM BPSK n (20MHz) 36 to 48 36, 40, 48 OFDM BPSK n (40MHz) 38 to 46 38, 46 OFDM BPSK ac (20MHz) 36 to 48 36, 40, 48 OFDM BPSK ac (40MHz) 38 to 46 38, 46 OFDM BPSK ac (80MHz) OFDM BPSK a 149 to , 157, 165 OFDM BPSK n (20MHz) 149 to , 157, 165 OFDM BPSK n (40MHz) 151 to , 159 OFDM BPSK ac (20MHz) 149 to , 157, 165 OFDM BPSK ac (40MHz) 151 to , 159 OFDM BPSK ac (80MHz) OFDM BPSK 87.8 TEST CONDITION: APPLICABLE TO ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY RE 1G 25deg. C, 60%RH 120Vac, 60Hz Tank Wu RE<1G 25deg. C, 60%RH 120Vac, 60Hz Tank Wu PLC 25deg. C, 60%RH 120Vac, 60Hz Tank Wu APCM 25deg. C, 60%RH 120Vac, 60Hz Frank Liu Report No.: RF141108C of 78 Report Format Version 5.3.0

12 3.3 DUTY CYCLE OF TEST SIGNAL For U-NII-1 Band: Duty cycle of test signal is > 98 %, duty factor is not required a n (20MHz) n (40MHz) ac (20MHz) ac (40MHz) ac (80MHz) Report No.: RF141108C of 78 Report Format Version 5.3.0

13 For U-NII-3 Band: Duty cycle of test signal is > 98 %, duty factor is not required a n (20MHz) n (40MHz) ac (20MHz) ac (40MHz) ac (80MHz) Report No.: RF141108C of 78 Report Format Version 5.3.0

14 3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. PRODUCT BRAND MODEL SERIAL FCC ID 1 HUB D-Link DIR-810 NA NA 2 UTM SOPHOS UTM110/120/100 rev.5 NA NA 3 NOTEBOOK DELL D531 CN-0XM U-2610 QDS-BRCM POE Power Desine PD-9001GR/AC NA NA 1 3m RJ45 Cable. 2 3m RJ45 Cable. 3 3m RJ45 Cable. 4 10m RJ45 Cable. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS NOTE: 1. All power cords of the above support units are non-shielded (1.8 m). 2. Item 2 & 4 were provided by the manufacturer. 3. Item 1-4 acted as a communication partner to transfer data. Report No.: RF141108C of 78 Report Format Version 5.3.0

15 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST EUT (Power from POE) *Test table 10m RJ45 cable 3m RJ45 cable POE Hub 3m RJ45 cable 3m RJ45 cable Notebook UTM *Kept in a remote area Report No.: RF141108C of 78 Report Format Version 5.3.0

16 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF Product. According to the specification of the EUT declared by the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart E (15.407) D02 General UNII Test Procedures New Rules v D01 Multiple Transmitter Output v02r01 ANSI C All test items have been performed and recorded as per the above standards. NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF141108C of 78 Report Format Version 5.3.0

17 4. TEST TYPES AND RESULTS 4.1 RADIATED AND BANDEDGE MEASUREMENT S OF RADIATED AND BANDEDGE MEASUREMENT Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table: FREQUENCIES FIELD STRENGTH (microvolts/meter) MEASUREMENT DISTANCE (meters) ~ /F(kHz) ~ /F(kHz) ~ ~ ~ ~ Above NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level = 20 log Emission level (uv/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation S OF UNWANTED OUT OF THE RESTRICTED BANDS APPLICABLE TO D02 General UNII Test Procedures New Rules v01 APPLICABLE TO (b)(1) PK: 74 (dbµv/m) EIRP FIELD STRENGTH AT 3m AV: 54 (dbµv/m) EQUIVALENT FIELD STRENGTH AT 3m (b)(2) PK: -27 (dbm/mhz) PK: 68.2 (dbµv/m) (b)(3) PK: -27 (dbm/mhz) *1 PK: 68.2 (dbµv/m) * (b)(4) PK: -17 (dbm/mhz) *2 PK: 78.2 (dbµv/m) *2 NOTE: *1 *2 beyond 10MHz of the band edge within 10 MHz of band edge The following formula is used to convert the equipment isotropic radiated power (eirp) to field strength: P E = µv/m, where P is the eirp (Watts). 3 Report No.: RF141108C of 78 Report Format Version 5.3.0

18 4.1.3 TEST INSTRUMENTS DESCRIPTION & MANUFACTURER Test Receiver ROHDE & SCHWARZ Spectrum Analyzer ROHDE & SCHWARZ BILOG Antenna SCHWARZBECK HORN Antenna SCHWARZBECK HORN Antenna SCHWARZBECK Preamplifier Agilent Preamplifier Agilent RF signal cable HUBER+SUHNNER MODEL SERIAL DATE OF CALIBRATION DUE DATE OF CALIBRATION ESCS Nov. 29, 2013 Nov. 28, 2014 FSP Feb. 11, 2014 Feb. 10, 2015 VULB Feb. 25, 2014 Feb. 24, 2015 BBHA 9120 D 9120D-209 Aug. 25, 2014 Aug. 24, 2015 BBHA 9170 BBHA Feb. 17, 2014 Feb. 16, B 3008A01911 Aug. 09, 2014 Aug. 08, D 2944A10638 Aug. 09, 2014 Aug. 08, 2015 SUCOFLEX / / /4 Aug. 09, 2014 Aug. 08, 2015 RF signal cable Worken 8D-FB Cable-CH9-01 Aug. 11, 2014 Aug. 10, 2015 Software ADT_Radiated_ BV ADT V NA NA NA Antenna Tower EMCO 2070/ NA NA Turn Table EMCO NA NA NA Antenna Tower &Turn Table Controller 2090 NA NA NA EMCO 26GHz ~ 40GHz Amplifier EM Oct. 18, 2014 Oct. 17, 2015 High Speed Peak Power Meter ML2495A Jul. 26, 2014 Jul. 25, 2015 Power Sensor MA2411B Jul. 26, 2014 Jul. 25, 2015 WIT Standard Temperature And Humidity Chamber TH-4S-C W Jun. 09, 2014 Jun. 08, 2015 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is The IC Site Registration No. is IC 7450F-9. Report No.: RF141108C of 78 Report Format Version 5.3.0

19 4.1.4 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 1/T (Duty cycle < 98%) or 10Hz(Duty cycle > 98%) for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported DEVIATION FROM TEST STANDARD No deviation. Report No.: RF141108C of 78 Report Format Version 5.3.0

20 4.1.6 TEST SETUP Frequency range 30MHz~1GHz Frequency range above 1GHz For the actual test configuration, please refer to the attached file (Test Setup Photo). Report No.: RF141108C of 78 Report Format Version 5.3.0

21 4.1.7 EUT OPERATING CONDITION a. Placed the EUT on the testing table. b. Prepared notebook to act as a communication partner and placed it outside of testing area. c. The communication partners connected with EUT via a RJ45 cable and run a test program (provided by manufacturer) to enable EUT under transmission condition continuously at specific channel frequency. d. The communication partner sent data to EUT by command "PING". Report No.: RF141108C of 78 Report Format Version 5.3.0

22 4.1.8 TEST RESULTS ABOVE 1GHz WORST-CASE DATA: a CHANNEL TX Channel 36 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.17 H * AV 1.17 H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.93 V * AV 1.93 V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

23 CHANNEL TX Channel 40 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.18 H * AV 1.18 H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

24 CHANNEL TX Channel 48 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.17 H * AV 1.17 H PK H AV H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

25 CHANNEL TX Channel 149 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 # PK H # AV H # PK H # PK H * PK 1.40 H * AV 1.40 H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 # PK V # AV V # PK V # PK V * PK 1.09 V * AV 1.09 V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

26 CHANNEL TX Channel 157 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 # PK H # AV H * PK 1.11 H * AV 1.11 H # PK H # AV H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 # PK V # AV V * PK 1.00 V * AV 1.00 V # PK V # AV V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

27 CHANNEL TX Channel 165 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 * PK 1.00 H * AV 1.00 H # PK H # PK H # PK H # AV H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 * PK 1.00 V * AV 1.00 V # PK V # PK V # PK V # AV V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

28 802.11n (20MHz) CHANNEL TX Channel 36 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.00 H * AV 1.00 H PK H AV H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.11 V * AV 1.11 V PK V AV V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

29 CHANNEL TX Channel 40 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.00 H * AV 1.00 H PK H AV H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

30 CHANNEL TX Channel 48 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.00 H * AV 1.00 H PK H AV H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

31 CHANNEL TX Channel 149 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 # PK H # AV H # PK H # PK H * PK 1.00 H * AV 1.00 H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 # PK V # AV V # PK V # PK V * PK 1.31 V * AV 1.31 V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

32 CHANNEL TX Channel 157 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 # PK H # AV H * PK 1.02 H * AV 1.02 H # PK H # AV H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 # PK V # AV V * PK 1.69 V * AV 1.69 V # PK V # AV V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

33 CHANNEL TX Channel 165 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 * PK 1.02 H * AV 1.02 H # PK H # PK H # PK H # AV H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 * PK 1.42 V * AV 1.42 V # PK V # PK V # PK V # AV V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

34 802.11n (40MHz) CHANNEL TX Channel 38 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.00 H * AV 1.00 H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

35 CHANNEL TX Channel 46 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.08 H * AV 1.08 H PK H AV H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

36 CHANNEL TX Channel 151 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 # PK H # AV H # PK H # PK H * PK 1.06 H * AV 1.06 H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 # PK V # AV V # PK V # PK V * PK 1.00 V * AV 1.00 V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

37 CHANNEL TX Channel 159 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 * PK 1.00 H * AV 1.00 H # PK H # PK H # PK H # AV H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 * PK 1.38 V * AV 1.38 V # PK V # PK V # PK V # AV V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

38 802.11ac (20MHz) CHANNEL TX Channel 36 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.00 H * AV 1.00 H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.11 V * AV 1.11 V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

39 CHANNEL TX Channel 40 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.00 H * AV 1.00 H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

40 CHANNEL TX Channel 48 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.01 H * AV 1.01 H PK H AV H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

41 CHANNEL TX Channel 149 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 # PK H # AV H # PK H # PK H * PK 1.01 H * AV 1.01 H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 # PK V # AV V # PK V # PK V * PK 1.00 V * AV 1.00 V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

42 CHANNEL TX Channel 157 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 * PK 1.03 H * AV 1.03 H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 * PK 1.00 V * AV 1.00 V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF141108C of 78 Report Format Version 5.3.0

43 CHANNEL TX Channel 165 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 * PK 1.01 H * AV 1.01 H # PK H # PK H # PK H # AV H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 * PK 1.00 V * AV 1.00 V # PK V # PK V # PK V # AV V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

44 802.11ac (40MHz) CHANNEL TX Channel 38 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.02 H * AV 1.02 H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

45 CHANNEL TX Channel 46 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.08 H * AV 1.08 H PK H AV H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.02 V * AV 1.02 V PK V AV V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

46 CHANNEL TX Channel 151 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 # PK H # AV H # PK H # PK H * PK 1.00 H * AV 1.00 H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 # PK V # AV V # PK V # PK V * PK 1.00 V * AV 1.00 V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

47 CHANNEL TX Channel 159 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 * PK 1.00 H * AV 1.00 H # PK H # PK H # PK H # AV H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 * PK 1.33 V * AV 1.33 V # PK V # PK V # PK V # AV V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

48 802.11ac (80MHz) CHANNEL TX Channel 42 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M PK H AV H * PK 1.00 H * AV 1.00 H # PK H # AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M PK V AV V * PK 1.00 V * AV 1.00 V # PK V # AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

49 CHANNEL TX Channel 155 FREQUENCY RANGE 1GHz ~ 40GHz DETECTOR FUNCTION Peak (PK) Average (AV) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M 1 # PK H # AV H # PK H # PK H * PK 1.00 H * AV 1.00 H # PK H # PK H # AV H PK H AV H POLARITY & TEST DISTANCE: VERTICAL AT 3 M 1 # PK V # AV V # PK V # PK V * PK 1.00 V * AV 1.00 V # PK V # PK V # AV V PK V AV V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. 6. " # ": The radiated frequency is out of the restricted band. Report No.: RF141108C of 78 Report Format Version 5.3.0

50 BELOW 1GHz WORST-CASE DATA: a CHANNEL TX Channel 36 FREQUENCY RANGE 30MHz ~ 1GHz DETECTOR FUNCTION Quasi-Peak (QP) POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M QP H QP H QP H QP H QP H QP H POLARITY & TEST DISTANCE: VERTICAL AT 3 M QP V QP V QP V QP V QP V QP V REMARKS: 1. Emission Level = Raw Value + Correction Factor 2. Correction Factor = Antenna Factor + Cable Factor Pre-Amplifier Factor 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value Report No.: RF141108C of 78 Report Format Version 5.3.0

51 4.2 CONDUCTED MEASUREMENT S OF CONDUCTED MEASUREMENT FREQUENCY OF CONDUCTED (dbµv) 0.15 ~ ~ 5 5 ~ 30 Quasi-peak 66 to Average 56 to NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above TEST INSTRUMENTS DESCRIPTION & MANUFACTURER Test Receiver ROHDE & SCHWARZ RF signal cable Woken LISN ROHDE & SCHWARZ (EUT) LISN ROHDE & SCHWARZ (Peripheral) Software ADT MODEL SERIAL DATE OF CALIBRATION DUE DATE OF CALIBRATION ESCI Sep. 30, 2014 Sep. 29, D-FB Cable-HYC01-01 Dec. 27, 2013 Dec. 26, 2014 ESH3-Z /001 Feb. 13, 2014 Feb. 12, 2015 ESH3-Z Jul. 21, 2014 Jul. 20, 2015 BV ADT_Cond_ V NA NA NA NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room The VCCI Site Registration No. is C Report No.: RF141108C of 78 Report Format Version 5.3.0

52 4.2.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) were not recorded. NOTE: All modes of operation were investigated and the worst-case emissions are reported DEVIATION FROM TEST STANDARD No deviation TEST SETUP Vertical Ground Reference Plane Test Receiver 40cm EUT 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 from other units and other metal planes For the actual test configuration, please refer to the attached file (Test Setup Photo) EUT OPERATING CONDITIONS Same as Report No.: RF141108C of 78 Report Format Version 5.3.0

53 4.2.7 TEST RESULTS CONDUCTED WORST-CASE DATA:802.11a PHASE Line 1 6dB BANDWIDTH 9kHz Emission Corr. Reading Value Limit Margin Freq. Level No Factor [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF141108C of 78 Report Format Version 5.3.0