FCC Test Report. Report No.: RF160715C03 FCC ID: PY Test Model: EX6150v2. Received Date: Jul. 11, Test Date: Jul. 15 ~ Aug.

Transcription

1 FCC Test Report Report No.: FCC ID: Test Model: RF160715C03 PY EX6150v2 Received Date: Jul. 11, 2016 Test Date: Jul. 15 ~ Aug. 02, 2016 Issued Date: Aug. 03, 2016 Applicant: NETGEAR Inc. Address: 350 East Plumeria Drive San Jose, CA Issued By: Lab Address: Test Location: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF160715C03 Page No. 1 / 64 Report Format Version: 6.1.1

2 Table of Contents Release Control Record Certificate of Conformity Summary of Test Results Measurement Uncertainty Modification Record General Information General Description of EUT Description of Test Modes Test Mode Applicability and Tested Channel Detail Duty Cycle of Test Signal Description of Support Units Configuration of System under Test General Description of Applied Standards Test Types and Results Radiated Emission and Bandedge Measurement Limits of Radiated Emission and Bandedge Measurement Test Instruments Test Procedures Deviation from Test Standard Test Set Up EUT Operating Conditions Test Results Conducted Emission Measurement Limits of Conducted Emission Measurement Test Instruments Test Procedures Deviation from Test Standard Test Setup EUT Operating Conditions Test Results dB Bandwidth Measurement Limits of 6dB Bandwidth Measurement Test Setup Test Instruments Test Procedure Deviation fromtest Standard EUT Operating Conditions Test Result Conducted Output Power Measurement Limits of Conducted Output Power Measurement Test Setup Test Instruments Test Procedures Deviation from Test Standard EUT Operating Conditions Test Results Power Spectral Density Measurement Limits of Power Spectral Density Measurement Test Setup Test Instruments Test Procedure Deviation from Test Standard EUT Operating Condition Report No.: RF160715C03 Page No. 2 / 64 Report Format Version: 6.1.1

3 4.5.7 Test Results Conducted Out of Band Emission Measurement Limits of Conducted Out of Band Emission Measurement Test Setup Test Instruments Test Procedure Deviation from Test Standard EUT Operating Condition Test Results Pictures of Test Arrangements Appendix Information on the Testing Laboratories Report No.: RF160715C03 Page No. 3 / 64 Report Format Version: 6.1.1

4 Release Control Record Issue No. Description Date Issued RF160715C03 Original release Aug. 03, 2016 Report No.: RF160715C03 Page No. 4 / 64 Report Format Version: 6.1.1

5 1 Certificate of Conformity Product: AC1200 WiFi Range Extender Brand: NETGEAR Test Model: EX6150v2 Sample Status: Engineering sample Applicant: NETGEAR Inc. Test Date: Jul. 15 ~ Aug. 02, 2016 Standards: 47 CFR FCC Part 15, Subpart C (Section ) ANSI C63.10:2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample s EMC characteristics under the conditions specified in this report. Prepared by :, Date: Aug. 03, 2016 Celine Chou / Specialist Approved by :, Date: Aug. 03, 2016 Ken Liu / Senior Manager Report No.: RF160715C03 Page No. 5 / 64 Report Format Version: 6.1.1

6 2 Summary of Test Results FCC Clause 47 CFR FCC Part 15, Subpart C (Section ) Test Item Result Remarks AC Power Conducted Emission Pass / / (d) Radiated Emissions and Band Edge Measurement Pass Meet the requirement of limit. Minimum passing margin is dB at MHz Meet the requirement of limit. Minimum passing margin is -0.1dB at MHz and MHz (d) Antenna Port Emission Pass Meet the requirement of limit (a)(2) 6dB bandwidth Pass Meet the requirement of limit (b) Conducted power Pass Meet the requirement of limit (e) Power Spectral Density Pass Meet the requirement of limit Antenna Requirement Pass Antenna connector is i-pex(mhf) not a standard connector. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR : Measurement Frequency Expanded Uncertainty (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 2.44 db Radiated Emissions up to 1 GHz Radiated Emissions above 1 GHz 30MHz ~ 200MHz 200MHz ~1000MHz 1GHz ~ 18GHz 18GHz ~ 40GHz 3.59 db 3.60 db 2.29 db 2.29 db 2.2 Modification Record There were no modifications required for compliance. Report No.: RF160715C03 Page No. 6 / 64 Report Format Version: 6.1.1

7 3 General Information 3.1 General Description of EUT Product Brand Test Model Sample Status Power Supply Rating Modulation Type Modulation Technology Transfer Rate Operating Frequency Number of Channel Output Power Antenna Type Antenna Connector Accessory Device Data Cable Supplied Note: AC1200 WiFi Range Extender NETGEAR EX6150v2 Engineering sample Vac CCK, DQPSK, DBPSK for DSSS 64QAM, 16QAM, QPSK, BPSK for OFDM DSSS, OFDM b:11.0/ 5.5/ 2.0/ 1.0Mbps g: 54.0/ 48.0/ 36.0/ 24.0/ 18.0/ 12.0/ 9.0/ 6.0Mbps n: up to 300Mbps 2412 ~ 2462MHz 11 for b, g, n (HT20) 7 for n (HT40) CDD Mode: mW Beamforming Mode: mW Dipole antenna with 2.29dBi gain i-pex(mhf) NA NA 1. The EUT incorporates a MIMO function. Physically, the EUT provides 2 completed transmitters and 2 receivers. Modulation Mode TX Function Beamforming b 2TX Not Support g 2TX Not Support n (HT20) 2TX Support n (HT40) 2TX Support * For 2.4GHz band, CDD mode is the worst case for final radiated emission and power line conducted emission tests after pretesting CDD mode and beamforming mode. *The EUT incorporates AP & Extender functions, they are comply with standard, therefore, we chose worse case for AP function to performed the representative test after assessment GHz and 5GHz technology can transmit at same time. 3. Spurious emission of the simultaneous operation (2.4GHz and 5GHz) has been evaluated and no non-compliance was found. Report No.: RF160715C03 Page No. 7 / 64 Report Format Version: 6.1.1

8 3.2 Description of Test Modes 11 channels are provided for b, g and n (HT20): Channel Frequency Channel Frequency MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz 7 channels are provided for n (HT40): Channel Frequency Channel Frequency MHz MHz MHz MHz MHz MHz MHz Report No.: RF160715C03 Page No. 8 / 64 Report Format Version: 6.1.1

9 3.2.1 Test Mode Applicability and Tested Channel Detail EUT CONFIGURE MODE APPLICABLE TO RE 1G RE<1G PLC APCM DESCRIPTION - - Where RE 1G: Radiated Emission above 1GHz & Bandedge Measurement PLC: Power Line Conducted Emission RE<1G: Radiated Emission below 1GHz APCM: Antenna Port Conducted Measurement Note: The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on X-plane. Radiated Emission Test (Above 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE b 1 to 11 1, 6, 11 DSSS DBPSK g 1 to 11 1, 6, 11 OFDM BPSK n (HT20) 1 to 11 1, 6, 11 OFDM BPSK n (HT40) 3 to 9 3, 6, 9 OFDM BPSK 15.0 (Mbps) Radiated Emission Test (Below 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE b 1 to 11 1 DSSS DBPSK 1.0 (Mbps) Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE b 1 to 11 1 DSSS DBPSK 1.0 (Mbps) Report No.: RF160715C03 Page No. 9 / 64 Report Format Version: 6.1.1

10 Antenna Port Conducted Measurement: This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE b 1 to 11 1, 6, 11 DSSS DBPSK g 1 to 11 1, 6, 11 OFDM BPSK n (HT20) 1 to 11 1, 6, 11 OFDM BPSK n (HT40) 3 to 9 3, 6, 9 OFDM BPSK 15.0 (Mbps) Test Condition: APPLICABLE TO ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY RE 1G 25deg. C, 65%RH 120Vac, 60Hz Chris Lin RE<1G 23deg. C, 70%RH 120Vac, 60Hz Chris Lin PLC 25deg. C, 65%RH 120Vac, 60Hz Tank Wu APCM 25deg. C, 60%RH 120Vac, 60Hz Antony Lee Report No.: RF160715C03 Page No. 10 / 64 Report Format Version: 6.1.1

11 3.3 Duty Cycle of Test Signal CDD Mode b: Duty cycle of test signal is > 98%, duty factor is not required g, n (HT20), n (HT40): Duty cycle of test signal is < 98%, duty factor shall be considered g: Duty cycle = 2.009/2.114 = 0.950, Duty factor = 10 * log( 1/0.950) = n (HT20): Duty cycle = 4.947/5.057 = 0.978, Duty factor = 10 * log( 1/0.978) = n (HT40): Duty cycle = 2.403/2.495 = 0.963, Duty factor = 10 * log( 1/0.963) = b g n (HT20) n (HT40) Report No.: RF160715C03 Page No. 11 / 64 Report Format Version: 6.1.1

12 Beamforming Mode n (HT20), n (HT40): Duty cycle of test signal is < 98%, duty factor shall be considered n (HT20): Duty cycle = 4.947/5.055 = 0.979, Duty factor = 10 * log( 1/0.979) = n (HT40): Duty cycle = 2.400/2.508 = 0.957, Duty factor = 10 * log( 1/0.957) = n (HT20) n (HT40) Report No.: RF160715C03 Page No. 12 / 64 Report Format Version: 6.1.1

13 3.4 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. ID Product Brand Model No. Serial No. FCC ID Remarks A. Notebook DELL E5410 6RP2YM1 FCC DoC Approved - Note: 1. All power cords of the above support units are non-shielded (1.8m). 2. Item A acted as communication partner to transfer data. ID Descriptions Qty. Length (m) Shielding (Yes/No) Cores (Qty.) 1. RJ45, Cat5e 1 3 N 0 - Remarks Configuration of System under Test EUT AC LAN 1 Remote site Notebook (A) 3.5 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.247) KDB D01 DTS Meas Guidance v03r05 KDB D01 Multiple Transmitter Output v02r01 ANSI C All test items have been performed and recorded as per the above standards. Note: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF160715C03 Page No. 13 / 64 Report Format Version: 6.1.1

14 4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement Limits of Radiated Emission and Bandedge Measurement Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 30dB below the highest level of the desired power: Frequencies Field Strength (microvolts/meter) Measurement Distance (meters) Note: ~ /F(kHz) ~ /F(kHz) ~ ~ ~ ~ Above The lower limit shall apply at the transition frequencies. 2. Emission level = 20 log Emission level (uv/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 30dB under any condition of modulation. Report No.: RF160715C03 Page No. 14 / 64 Report Format Version: 6.1.1

15 4.1.2 Test Instruments Description & Manufacturer Test Receiver ROHDE & SCHWARZ Spectrum Analyzer ROHDE & SCHWARZ BILOG Antenna SCHWARZBECK HORN Antenna SCHWARZBECK HORN Antenna SCHWARZBECK Preamplifier Agilent Preamplifier Agilent RF signal cable HUBER+SUHNER RF signal cable HUBER+SUHNER Software BV ADT Antenna Tower inn-co GmbH Antenna Tower Controller BV ADT Turn Table BV ADT Turn Table Controller BV ADT High Speed Peak Power Meter Model No. Serial No. Cal. Date Cal. Due ESCI Oct. 12, 2015 Oct. 11, 2016 FSP Jul. 08, 2016 Jul. 07, 2017 VULB Jan. 07, 2016 Jan. 06, 2017 BBHA 9120D 9120D-1170 Jan. 08, 2016 Jan. 07, 2017 BBHA 9170 BBHA Jan. 18, 2016 Jan. 17, B 3008A01960 Aug. 09, 2015 Aug. 08, D 2944A10631 Aug. 09, 2015 Aug. 08, 2016 SUCOFLEX 104 MY /04 Jul. 18, 2015 Jul. 17, 2016 Jul. 18, 2016 Jul. 17, 2017 SUCOFLEX 104 Cable-CH4-03(250724) Aug. 09, 2015 Aug. 08, 2016 ADT_Radiated_ V NA NA NA MA NA NA AT100 AT NA NA TT100 TT NA NA SC100. SC NA NA ML2495A Power Sensor MA2411B Jul. 09, 2015 Jul. 08, 2016 Jul. 09, 2016 Jul. 08, 2017 Jul. 09, 2015 Jul. 08, 2016 Jul. 09, 2016 Jul. 08, 2017 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber The horn antenna and preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is The IC Site Registration No. is IC7450F-4. Report No.: RF160715C03 Page No. 15 / 64 Report Format Version: 6.1.1

16 4.1.3 Test Procedures a. The EUT was placed on the top of a rotating table 0.8 meters (for below 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 3MHz for RMS Average (Duty cycle < 98%) for Average detection (AV) at frequency above 1GHz, then the measurement results was added to a correction factor (10 log(1/duty cycle)). 4. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 10Hz (Duty cycle 98%) for Average detection (AV) at frequency above 1GHz. 5. All modes of operation were investigated and the worst-case emissions are reported Deviation from Test Standard No deviation. Report No.: RF160715C03 Page No. 16 / 64 Report Format Version: 6.1.1

17 4.1.5 Test Set Up <Frequency Range below 1GHz> EUT& Support Units 3m 10m Ant. Tower 1-4m Variable Turn Table 80cm Ground Plane Test Receiver <Frequency Range above 1GHz> EUT& Support Units 3m Ant. Tower 1-4m Variable Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo) EUT Operating Conditions a. Placed the EUT on the testing table. b. Prepared a notebook to act as a communication partner and placed it outside of testing area. c. The communication partner connected with EUT via a RJ45 cable and ran a test program (provided by manufacturer) to enable EUT under transmission condition continuously at specific channel frequency. d. The communication partner sent data to EUT by command "PING". Report No.: RF160715C03 Page No. 17 / 64 Report Format Version: 6.1.1

18 4.1.7 Test Results Above 1GHz Worst-Case data: b CHANNEL TX Channel 1 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK H AV H * PK 1.03 H * AV 1.03 H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 18 / 64 Report Format Version: 6.1.1

19 CHANNEL TX Channel 6 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK H AV H * PK 1.04 H * AV 1.04 H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 19 / 64 Report Format Version: 6.1.1

20 CHANNEL TX Channel 11 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) 1 * PK 1.00 H * AV 1.00 H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) 1 * PK 1.00 V * AV 1.00 V PK V AV V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 20 / 64 Report Format Version: 6.1.1

21 802.11g CHANNEL TX Channel 1 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK H AV H * PK 1.05 H * AV 1.05 H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 21 / 64 Report Format Version: 6.1.1

22 CHANNEL TX Channel 6 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK H AV H * PK 1.05 H * AV 1.05 H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK V AV V * PK 1.33 V * AV 1.33 V PK V AV V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 22 / 64 Report Format Version: 6.1.1

23 CHANNEL TX Channel 11 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) 1 * PK 1.04 H * AV 1.04 H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) 1 * PK 1.00 V * AV 1.00 V PK V AV V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 23 / 64 Report Format Version: 6.1.1

24 802.11n (HT20) CHANNEL TX Channel 1 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK H AV H * PK 1.87 H * AV 1.87 H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK V AV V * PK 1.13 V * AV 1.13 V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 24 / 64 Report Format Version: 6.1.1

25 CHANNEL TX Channel 6 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK H AV H * PK 1.33 H * AV 1.33 H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK V AV V * PK 1.86 V * AV 1.86 V PK V AV V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 25 / 64 Report Format Version: 6.1.1

26 CHANNEL TX Channel 11 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) 1 * PK 1.47 H * AV 1.47 H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) 1 * PK 1.00 V * AV 1.00 V PK V AV V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 26 / 64 Report Format Version: 6.1.1

27 802.11n (HT40) CHANNEL TX Channel 3 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK H AV H * PK 1.33 H * AV 1.33 H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 27 / 64 Report Format Version: 6.1.1

28 CHANNEL TX Channel 6 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK H AV H * PK 1.33 H * AV 1.33 H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) PK V AV V * PK 1.11 V * AV 1.11 V PK V AV V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 28 / 64 Report Format Version: 6.1.1

29 CHANNEL TX Channel 9 FREQUENCY RANGE 1GHz ~ 25GHz DETECTOR FUNCTION Peak (PK) Average (AV) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) 1 * PK 2.22 H * AV 2.22 H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) 1 * PK 1.00 V * AV 1.00 V PK V AV V PK V AV V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. " * ": Fundamental frequency. Report No.: RF160715C03 Page No. 29 / 64 Report Format Version: 6.1.1

30 Below 1GHz worst-case data: b CHANNEL TX Channel 1 FREQUENCY RANGE 30MHz ~ 1GHz DETECTOR FUNCTION Quasi-Peak (QP) NO. FREQ. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M NO. FREQ. EMISSION LEVEL LIMIT MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) QP V QP V QP V QP V QP V QP V Remarks: 1. Emission Level = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value Report No.: RF160715C03 Page No. 30 / 64 Report Format Version: 6.1.1

31 4.2 Conducted Emission Measurement Limits of Conducted Emission Measurement Frequency Conducted Limit (dbuv) Quasi-peak Average Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz Test Instruments Description & Manufacturer Model No. Serial No. Cal. Date Cal. Due Test Receiver ROHDE & SCHWARZ RF signal cable (with 10dB PAD) Woken LISN/AMN ROHDE & SCHWARZ (EUT) LISN/AMN ROHDE & SCHWARZ (Peripheral) Software ADT ESCI Nov. 16, 2015 Nov. 15, D-FB Cable-cond1-01 Dec. 26, 2015 Dec. 25, 2016 ESH3-Z /001 Feb. 26, 2016 Feb. 25, 2017 ESH3-Z Nov. 13, 2015 Nov. 12, 2016 BV ADT_Cond_ V NA NA NA Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room The VCCI Site Registration No. is C Report No.: RF160715C03 Page No. 31 / 64 Report Format Version: 6.1.1

32 4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz Deviation from Test Standard No deviation Test Setup Vertical Ground Reference Plane Test Receiver 40cm EUT 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo) EUT Operating Conditions Same as Report No.: RF160715C03 Page No. 32 / 64 Report Format Version: 6.1.1

33 4.2.7 Test Results Phase Line (L) Detector Function Quasi-Peak (QP) / Average (AV) No Freq. Corr. Factor Reading Value Emission Level Limit Margin [db (uv)] [db (uv)] [db (uv)] (db) [MHz] (db) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF160715C03 Page No. 33 / 64 Report Format Version: 6.1.1

34 Phase Neutral (N) Detector Function Quasi-Peak (QP) / Average (AV) No Freq. Corr. Factor Reading Value Emission Level Limit Margin [db (uv)] [db (uv)] [db (uv)] (db) [MHz] (db) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level - Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value. Report No.: RF160715C03 Page No. 34 / 64 Report Format Version: 6.1.1

35 4.3 6dB Bandwidth Measurement Limits of 6dB Bandwidth Measurement The minimum of 6dB Bandwidth Measurement is 0.5 MHz Test Setup EUT Attenuator Spectrum Analyzer Test Instruments Refer to section to get information of above instrument Test Procedure a. Set resolution bandwidth (RBW) = 100kHz b. Set the video bandwidth (VBW) 3 x RBW, Detector = average. c. Trace mode = max hold. d. Sweep = auto couple. e. Measure the maximum width of the emission that is constrained by the frequencies associated with the two amplitude points (upper and lower) that are attenuated by 6 db relative to the maximum level measured in the fundamental emission Deviation fromtest Standard No deviation EUT Operating Conditions The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. Report No.: RF160715C03 Page No. 35 / 64 Report Format Version: 6.1.1

36 4.3.7 Test Result CDD Mode b Channel Frequency 6dB Bandwidth Chain 0 Chain 1 Minimum Limit Pass / Fail Pass Pass Pass g Channel Frequency 6dB Bandwidth Chain 0 Chain 1 Minimum Limit Pass / Fail Pass Pass Pass n (HT20) Channel Frequency 6dB Bandwidth Chain 0 Chain 1 Minimum Limit Pass / Fail Pass Pass Pass n (HT40) Channel Frequency 6dB Bandwidth Chain 0 Chain 1 Minimum Limit Pass / Fail Pass Pass Pass Report No.: RF160715C03 Page No. 36 / 64 Report Format Version: 6.1.1

37 Spectrum Plot of Worst Value b g n (HT20) n (HT40) Report No.: RF160715C03 Page No. 37 / 64 Report Format Version: 6.1.1

38 Beamforming Mode n (HT20) Channel Frequency 6dB Bandwidth Chain 0 Chain 1 Minimum Limit Pass / Fail Pass Pass Pass n (HT40) Channel Frequency 6dB Bandwidth Chain 0 Chain 1 Minimum Limit Pass / Fail Pass Pass Pass Spectrum Plot of Worst Value n (HT20) n (HT40) Report No.: RF160715C03 Page No. 38 / 64 Report Format Version: 6.1.1

39 4.4 Conducted Output Power Measurement Limits of Conducted Output Power Measurement For systems using digital modulation in the MHz bands: 1 Watt (30dBm) Per KDB D01 Multiple Transmitter Output Method of conducted output power measurement on IEEE devices, Array Gain = 0 db (i.e., no array gain) for NANT 4; Array Gain = 0 db (i.e., no array gain) for channel widths 40 MHz for any NANT; Array Gain = 5 log(nant/nss) db or 3 db, whichever is less for 20-MHz channel widths with NANT 5. For power measurements on all other devices: Array Gain = 10 log(nant/nss) db Test Setup EUT Power Sensor Power Meter Attenuator Test Instruments Refer to section to get information of above instrument Test Procedures An average power sensor was used on the output port of the EUT. A power meter was used to read the response of the average power sensor. Record the power level Deviation from Test Standard No deviation EUT Operating Conditions Same as Item Report No.: RF160715C03 Page No. 39 / 64 Report Format Version: 6.1.1

40 4.4.7 Test Results CDD Mode b Channel g Frequency Average Power (dbm) Chain 0 Chain 1 Total Power (mw) Total Power (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Channel Frequency Average Power (dbm) Chain 0 Chain 1 Total Power (mw) Total Power (dbm) Limit (dbm) Pass / Fail Pass Pass Pass n (HT20) Channel Frequency Average Power (dbm) Chain 0 Chain 1 Total Power (mw) Total Power (dbm) Limit (dbm) Pass / Fail Pass Pass Pass n (HT40) Channel Frequency Average Power (dbm) Chain 0 Chain 1 Total Power (mw) Total Power (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Report No.: RF160715C03 Page No. 40 / 64 Report Format Version: 6.1.1

41 Beamforming Mode n (HT20) Channel Frequency Average Power (dbm) Chain 0 Chain 1 Total Power (mw) Total Power (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Note: Directional gain = 2.29dBi + 10log(2) = 5.30dBi < 6dBi, so the power limit is not reduced n (HT40) Channel Frequency Average Power (dbm) Chain 0 Chain 1 Total Power (mw) Total Power (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Note: Directional gain = 2.29dBi + 10log(2) = 5.30dBi < 6dBi, so the power limit is not reduced. Report No.: RF160715C03 Page No. 41 / 64 Report Format Version: 6.1.1

42 4.5 Power Spectral Density Measurement Limits of Power Spectral Density Measurement The Maximum of Power Spectral Density Measurement is 8dBm Test Setup EUT Attenuator Spectrum Analyzer Test Instruments Refer to section to get information of above instrument Test Procedure For duty cycle 98% a. Set instrument center frequency to DTS channel center frequency. b. Set span to at least 1.5 times the OBW. c. Set RBW to: 3 khz RBW 100 khz.. d. Set VBW 3 x RBW. e. Detector = power averaging (RMS) or sample detector (when RMS not available). f. Ensure that the number of measurement points in the sweep 2 x span/rbw. g. Sweep time = auto couple. h. Employ trace averaging (RMS) mode over a minimum of 100 traces. i. Use the peak marker function to determine the maximum amplitude level. For duty cycle < 98% a. Measure the duty cycle (x). b. Set instrument center frequency to DTS channel center frequency. c. Set span to at least 1.5 times the OBW. d. Set RBW to: 3 khz RBW 100 khz.. e. Set VBW 3 x RBW. f. Detector = power averaging (RMS) or sample detector (when RMS not available). g. Ensure that the number of measurement points in the sweep 2 x span/rbw. h. Sweep time = auto couple. i. Do not use sweep triggering. Allow sweep to free run. j. Employ trace averaging (RMS) mode over a minimum of 100 traces. k. Use the peak marker function to determine the maximum amplitude level. l. Add 10 log (1/x), where x is the duty cycle measured in step (a, to the measured PSD to compute the average PSD during the actual transmission time. Report No.: RF160715C03 Page No. 42 / 64 Report Format Version: 6.1.1

43 4.5.5 Deviation from Test Standard No deviation EUT Operating Condition Same as Item Report No.: RF160715C03 Page No. 43 / 64 Report Format Version: 6.1.1

44 4.5.7 Test Results CDD Mode b TX chain Channel Frequency PSD (dbm) 10 log (N=2) db Total PSD (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Pass Pass Pass Note: 1. Method 1 of power density measurement of KDB is using for calculating total power density. Total power density is summing entire spectra across corresponding frequency bins on the various outputs by computer. 2. Directional gain = 2.29dBi + 10log(2) = 5.30dBi < 6dBi, so the power density limit no need to reduced g TX chain Channel Frequency PSD (dbm) 10 log (N=2) db Duty Factor Total PSD with Duty Factor (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Pass Pass Pass Note: 1. Method 1 of power density measurement of KDB is using for calculating total power density. Total power density is summing entire spectra across corresponding frequency bins on the various outputs by computer. 2. Directional gain = 2.29dBi + 10log(2) = 5.30dBi < 6dBi, so the power density limit no need to reduced. 3. Refer to section 3.3 for duty cycle spectrum plot. Report No.: RF160715C03 Page No. 44 / 64 Report Format Version: 6.1.1

45 802.11n (HT20) TX chain Channel Frequency PSD (dbm) 10 log (N=2) db Duty Factor Total PSD with Duty Factor (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Pass Pass Pass Note: 1. Method 1 of power density measurement of KDB is using for calculating total power density. Total power density is summing entire spectra across corresponding frequency bins on the various outputs by computer. 2. Directional gain = 2.29dBi + 10log(2) = 5.30dBi < 6dBi, so the power density limit no need to reduced. 3. Refer to section 3.3 for duty cycle spectrum plot n (HT40) TX chain Channel Frequency PSD (dbm) 10 log (N=2) db Duty Factor Total PSD with Duty Factor (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Pass Pass Pass Note: 1. Method 1 of power density measurement of KDB is using for calculating total power density. Total power density is summing entire spectra across corresponding frequency bins on the various outputs by computer. 2. Directional gain = 2.29dBi + 10log(2) = 5.30dBi < 6dBi, so the power density limit no need to reduced. 3. Refer to section 3.3 for duty cycle spectrum plot. Report No.: RF160715C03 Page No. 45 / 64 Report Format Version: 6.1.1

46 Spectrum Plot of Worst Value b g n (HT20) n (HT40) Report No.: RF160715C03 Page No. 46 / 64 Report Format Version: 6.1.1

47 Beamforming Mode n (HT20) TX chain Channel Frequency PSD (dbm) 10 log (N=2) db Duty Factor Total PSD with Duty Factor (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Pass Pass Pass Note: 1. Method 1 of power density measurement of KDB is using for calculating total power density. Total power density is summing entire spectra across corresponding frequency bins on the various outputs by computer. 2. Directional gain = 2.29dBi + 10log(2) = 5.30dBi < 6dBi, so the power density limit no need to reduced. 3. Refer to section 3.3 for duty cycle spectrum plot n (HT40) TX chain Channel Frequency PSD (dbm) 10 log (N=2) db Duty Factor Total PSD with Duty Factor (dbm) Limit (dbm) Pass / Fail Pass Pass Pass Pass Pass Pass Note: 1. Method 1 of power density measurement of KDB is using for calculating total power density. Total power density is summing entire spectra across corresponding frequency bins on the various outputs by computer. 2. Directional gain = 2.29dBi + 10log(2) = 5.30dBi < 6dBi, so the power density limit no need to reduced. 3. Refer to section 3.3 for duty cycle spectrum plot. Report No.: RF160715C03 Page No. 47 / 64 Report Format Version: 6.1.1

48 Spectrum Plot of Worst Value n (HT20) n (HT40) Report No.: RF160715C03 Page No. 48 / 64 Report Format Version: 6.1.1

49 4.6 Conducted Out of Band Emission Measurement Limits of Conducted Out of Band Emission Measurement Below 30dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth) Test Setup EUT Attenuator SPECTRUM ANALYZER Test Instruments Refer to section to get information of above instrument Test Procedure MEASUREMENT PROCEDURE REF a. Set the RBW = 100 khz. b. Set the VBW 300 khz. c. Detector = average. d. Sweep time = auto couple. e. Trace mode = max hold. f. Allow trace to fully stabilize. g. Use the peak marker function to determine the maximum power level in any 100 khz band segment within the fundamental EBW. MEASUREMENT PROCEDURE OOBE a. Set RBW = 100 khz. b. Set VBW 300 khz. c. Ensure that the number of measurement points span/rbw d. According to measurement points to set differ measurement span. e. Detector = average. f. Trace Mode = max hold. g. Sweep = auto couple. Report No.: RF160715C03 Page No. 49 / 64 Report Format Version: 6.1.1

50 4.6.5 Deviation from Test Standard No deviation EUT Operating Condition Same as Item Test Results The spectrum plots are attached on the following pages. D1 line indicates the highest level, and D2 line indicates the 30dB offset below D1. It shows compliance with the requirement. Report No.: RF160715C03 Page No. 50 / 64 Report Format Version: 6.1.1

51 CDD Mode b_Chain 0 CH 1 CH 6 CH 11 Report No.: RF160715C03 Page No. 51 / 64 Report Format Version: 6.1.1

52 802.11b_Chain 1 CH 1 CH 6 CH 11 Report No.: RF160715C03 Page No. 52 / 64 Report Format Version: 6.1.1

53 802.11g_Chain 0 CH 1 CH 6 CH 11 Report No.: RF160715C03 Page No. 53 / 64 Report Format Version: 6.1.1

54 802.11g_Chain 1 CH 1 CH 6 CH 11 Report No.: RF160715C03 Page No. 54 / 64 Report Format Version: 6.1.1

55 802.11n (HT20)_Chain 0 CH 1 CH 6 CH 11 Report No.: RF160715C03 Page No. 55 / 64 Report Format Version: 6.1.1

56 802.11n (HT20)_Chain 1 CH 1 CH 6 CH 11 Report No.: RF160715C03 Page No. 56 / 64 Report Format Version: 6.1.1