FCC TEST REPORT (RFID)

Transcription

1 FCC TEST REPORT (RFID) REPORT NO.: RF130923D14-2 MODEL NO.: DC-NU2-UMPC FCC ID: 2AA69001 RECEIVED: Sep. 23, 2013 TESTED: Oct. 11 ~ 17, 2013 ISSUED: Oct. 25, 2013 APPLICANT: Capsule Technologie SAS ADDRESS: 9 villa Pierre Ginier Paris, France ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF130923D of 27 Report Format Version 5.0.0

2 Table of Contents RELEASE CONTROL RECORD CERTIFICATION SUMMARY OF TEST RESULTS MEASUREMENT UNCERTAINTY GENERAL INFORMATION GENERAL DESCRIPTION OF EUT DESCRIPTION OF TEST MODES TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL DESCRIPTION OF SUPPORT UNITS CONFIGURATION OF SYSTEM UNDER TEST GENERAL DESCRIPTION OF APPLIED STANDARDS TEST TYPES AND RESULTS RADIATED EMISSION MEASUREMENT LIMITS OF RADIATED EMISSION MEASUREMENT TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS CONDUCTED EMISSION MEASUREMENT LIMITS OF CONDUCTED EMISSION MEASUREMENT TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS FREQUENCY STABILITY LIMITS OF FREQUENCY STABILITY MEASUREMENT TEST INSTRUMENTS TEST PROCEDURE DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITION TEST RESULTS PHOTOGRAPHS OF THE TEST CONFIGURATION INFORMATION ON THE TESTING LABORATORIES APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB Report No.: RF130923D of 27 Report Format Version 5.0.0

3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF130923D14-2 Original release Oct. 25, 2013 Report No.: RF130923D of 27 Report Format Version 5.0.0

4 1. CERTIFICATION PRODUCT: Neuron 2 BRAND NAME: Capsule MODEL: DC-NU2-UMPC APPLICANT: Capsule Technologie SAS TESTED: Oct. 11 ~ 17, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart C (Section ) ANSI C The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample s EMC characteristics under the conditions specified in this report. PREPARED BY :, DATE: Oct. 25, 2013 ( Annie Chang / Supervisor ) APPROVED BY :, DATE: Oct. 25, 2013 ( Rex Lai / Assistant Manager ) Report No.: RF130923D of 27 Report Format Version 5.0.0

5 2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC PART 15, SUBPART C (SECTION , ) STANDARD SECTION TEST TYPE AND LIMIT RESULT REMARK Conducted emission test PASS (a) (d) The field strength of any emissions within the band MHz The field strength of any emissions appearing outside of the MHz band PASS PASS Meet the requirement of limit. Minimum passing margin is -5.73dB at MHz. Meet the requirement of limit. Minimum passing margin is -72.3dB at 13.56MHz. Meet the requirement of limit. Minimum passing margin is -6.0dB at MHz (e) The frequency tolerance PASS Meet the requirement of limit. 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR : MEASUREMENT FREQUENCY UNCERTAINTY Conducted Emission 150kHz ~ 30MHz 2.44 db Radiated emissions 30MHz ~ 200MHz 200MHz ~1000MHz 4.30 db 3.36 db This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Report No.: RF130923D of 27 Report Format Version 5.0.0

6 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT Neuron 2 MODEL NO. DC-NU2-UMPC POWER SUPPLY MODULATION TYPE OPERATING FREQUENCY ANTENNA TYPE DATA CABLE I/O PORTS ACCESSORY DEVICES 17-21Vdc from Adapter or 11.1Vdc from battery ASK 13.56MHz PCB antenna N/A Refer to user s manual Refer to Note as below NOTE: 1. The EUT was power supplied from the following power adapter or battery: Item Brand Model Spec. Adapter PROTEK POWER PMP B5 AC I/P: V, A, 47-63Hz DC O/P: 17-21V, 3.53A, 60W Non-shielded AC 3-pin cable (1.8m) Non-shielded DC cable (1.3m) with one ferrite core. Battery 1 Capsule DC-NU2-BAT 11.1V, 2.6Ah, 28.8Wh Battery 2 Capsule DC-NU2-EXTBAT 11.1V, 5.2Ah, 57.7Wh 2. The EUT was pre-tested with the following modes: Operating Mode (EUT stand-alone) Operating + Charging Mode (EUT + Adapter) The worst emission level was found when the EUT tested under Operating + Charging Mode (EUT + Adapter), therefore, only its test data was recorded in this report. 3. The above EUT information is declared by the manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF130923D of 27 Report Format Version 5.0.0

7 3.2 DESCRIPTION OF TEST MODES TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL EUT CONFIGURE MODE APPLICABLE TO RE PLC FS - - Where RE: Radiated Emission PLC: Power Line Conducted Emission FS: Frequency Stability DESCRIPTION NOTE: The EUT had been pre-tested on the positioned of 3 axis. The worst case was found when positioned on Y-plane. RADIATED EMISSION TEST: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 1 ASK POWER LINE CONDUCTED EMISSION TEST: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 1 ASK FREQUENCY STABILITY: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE 1 1 ASK TEST CONDITION: APPLICABLE TO ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY RE 24deg. C, 77% RH 120Vac, 60Hz Joey Liu PLC 26deg. C, 78% RH 120Vac, 60Hz Aaron You FS 24deg. C, 70%RH 120Vac, 60Hz Dalen Dai Report No.: RF130923D of 27 Report Format Version 5.0.0

8 3.3 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID 1 USB KEYBOARD BTC 5200U G E5XKB5122U 2 USB Mouse Microsoft FCC DOC Approved NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS m braid shielded wire, terminated with USB connector via drain wire, w/o core m braid shielded wire, terminated with USB connector via drain wire, w/. one core. NOTE: All power cords of the above support units are non shielded (1.8m) CONFIGURATION OF SYSTEM UNDER TEST EUT Adapter Test table USB Keyboard USB Mouse Report No.: RF130923D of 27 Report Format Version 5.0.0

9 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RFID Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.225) ANSI C All test items have been performed and recorded as per the above standards. NOTE: The product has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF130923D of 27 Report Format Version 5.0.0

10 4. TEST TYPES AND RESULTS 4.1 RADIATED EMISSION MEASUREMENT LIMITS OF RADIATED EMISSION MEASUREMENT The field strength of any emissions within the band MHz shall not exceed 15,848 microvolts/meter at 30 meters. The field strength of any emissions appearing outside of the MHz band shall not exceed the general radiated emission limits in FREQUENCIES (MHz) FIELD STRENGTH (microvolts/meter) MEASUREMENT DISTANCE (meters) ~ /F(kHz) ~ /F(kHz) ~ ~ ~ ~ Above NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dbuv/m) = 20 log Emission level (uv/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF130923D of 27 Report Format Version 5.0.0

11 4.1.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL HP Preamplifier 8447D 2432A03504 Feb. 26, 2013 Feb. 25, 2014 HP Preamplifier 8449B 3008A01201 Feb. 26, 2013 Feb. 25, 2014 Agilent TEST RECEIVER N9038A MY Jan. 03, 2013 Jan. 02, 2014 Schwarzbeck Antenna VULB Mar. 20, 2013 Mar. 19, 2014 Schwarzbeck Antenna VHBA May 29, 2013 May 28, 2014 ADT. Turn Table TT NA NA ADT. Tower AT NA NA Software ADT_Radiated_V NA NA NA SUHNER RF cable SF102 CABLE-CH6 Aug. 19, 2013 Aug. 18, 2014 Schwarzbeck Horn Antenna Highpass filter Wainwright Instruments ROHDE & SCHWARZ Spectrum Analyzer Anritsu Power Sensor Anritsu Power Meter BBHA 9120-D1 D130 May 13, 2013 May 12, 2014 WHK 3.1/18G-10SS SN 8 NA NA FSP May. 17, 2013 May. 16, 2014 MA2411B Apr. 24, 2013 Apr. 23, 2014 ML2495A Apr. 25, 2013 Apr. 24, 2014 NOTE: 1. The calibration interval of the above test instruments is 12/24 months. And the calibrations are traceable to NML/ROC and NIST/USA. 2. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 3. The test was performed in Chamber No The Industry Canada Reference No. IC 7450E The FCC Site Registration No. is Report No.: RF130923D of 27 Report Format Version 5.0.0

12 4.1.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth is 3MHz for Peak detection at frequency above 1GHz. 3. All modes of operation were investigated and the worst-case emissions are reported DEVIATION FROM TEST STANDARD No deviation. Report No.: RF130923D of 27 Report Format Version 5.0.0

13 4.1.5 TEST SETUP For the actual test configuration, please refer to the attached file (Test Setup Photo) EUT OPERATING CONDITIONS The EUT ran a test program (provided by manufacturer) to enable EUT under transmission condition continuously at specific channel frequency. Report No.: RF130923D of 27 Report Format Version 5.0.0

14 4.1.7 TEST RESULTS CHANNEL TX Channel 1 FREQUENCY RANGE 13.56MHz DETECTOR FUNCTION Quasi-Peak No. Freq. (MHz) ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA OPEN AT 3m Emission Level (dbuv/m) Limit (dbuv/m) Margin (db) Antenna Height (m) Table Angle (Degree) Raw Value (dbuv) Correction Factor (db/m) REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. Above limits have been translated by the formula The measured field strength was extrapolated to distance 30 meters, using the formula that the limit of field strength varies as the inverse distance square (40dB per decade of distance) Example: 13.56MHz = 15848uV/m 30m = 84dBuV/m 30m = 84+20log(30/3) 2 3m = 124dBuV/m Report No.: RF130923D of 27 Report Format Version 5.0.0

15 CHANNEL TX Channel 1 FREQUENCY RANGE 13.56MHz DETECTOR FUNCTION Quasi-Peak No. Freq. (MHz) ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA CLOSE AT 3m Emission Level (dbuv/m) Limit (dbuv/m) Margin (db) Antenna Height (m) Table Angle (Degree) Raw Value (dbuv) Correction Factor (db/m) REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value 5. Above limits have been translated by the formula The measured field strength was extrapolated to distance 30 meters, using the formula that the limit of field strength varies as the inverse distance square (40dB per decade of distance) Example: 13.56MHz = 15848uV/m 30m = 84dBuV/m 30m = 84+20log(30/3) 2 3m = 124dBuV/m Report No.: RF130923D of 27 Report Format Version 5.0.0

16 CHANNEL TX Channel 1 FREQUENCY RANGE 9kHz 30MHz DETECTOR FUNCTION Quasi-Peak No. Freq. (MHz) ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA OPEN AT 3m Emission Level (dbuv/m) Limit (dbuv/m) Margin (db) Antenna Height (m) Table Angle (Degree) Raw Value (dbuv) Correction Factor (db/m) QP H ANTENNA POLARITY & TEST DISTANCE: LOOP ANTENNA CLOSE AT 3m No. Freq. (MHz) Emission Level (dbuv/m) Limit (dbuv/m) Margin (db) Antenna Height (m) Table Angle (Degree) Raw Value (dbuv) Correction Factor (db/m) QP V REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value Report No.: RF130923D of 27 Report Format Version 5.0.0

17 CHANNEL TX Channel 1 FREQUENCY RANGE MHz DETECTOR FUNCTION Quasi-Peak NO. FREQ. (MHz) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION LEVEL (dbuv/m) LIMIT (dbuv/m) MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) QP H QP H QP H QP H QP H QP H NO. FREQ. (MHz) ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION LEVEL (dbuv/m) LIMIT (dbuv/m) MARGIN (db) ANTENNA HEIGHT (m) TABLE ANGLE (Degree) RAW VALUE (dbuv) CORRECTION FACTOR (db/m) QP V QP V QP V QP V QP V QP V QP V REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level Limit value Report No.: RF130923D of 27 Report Format Version 5.0.0

18 4.2 CONDUCTED EMISSION MEASUREMENT LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz) CONDUCTED LIMIT (dbµv) 0.15 ~ ~ 5 5 ~ 30 Quasi-peak 66 to Average 56 to NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz TEST INSTRUMENTS DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL ROHDE & SCHWARZ TEST RECEIVER ESCS Jan. 07, 2013 Jan. 06, 2014 ROHDE & SCHWARZ Artificial Mains Network ESH3-Z Nov. 28, 2012 Nov. 27, 2013 (for EUT) LISN With Adapter (for EUT) AD10 C10Ada-001 Nov. 28, 2012 Nov. 27, 2013 ROHDE & SCHWARZ Artificial Mains Network (for peripherals) ESH3-Z Dec. 05, 2012 Dec. 04, 2013 Software ADT_Cond_V7.3.7 NA NA NA Software ADT_ISN_V7.3.7 NA NA NA RF cable (JYEBAO) 5D-FB Cable-C10.01 Feb. 19, 2013 Feb. 18, 2014 SUHNER Terminator (For ROHDE & SCHWARZ LISN) 65BNC-5001 E Feb. 06, 2013 Feb. 05, 2014 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No The VCCI Site Registration No. C Report No.: RF130923D of 27 Report Format Version 5.0.0

19 4.2.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. NOTE: All modes of operation were investigated and the worst-case emissions are reported DEVIATION FROM TEST STANDARD No deviation TEST SETUP Vertical Ground Reference Plane Test Receiver 40cm EUT 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 from other units and other metal planes For the actual test configuration, please refer to the attached file (Test Setup Photo) EUT OPERATING CONDITIONS Same as Report No.: RF130923D of 27 Report Format Version 5.0.0

20 4.2.7 TEST RESULTS PHASE Line 1 6dB BANDWIDTH 9kHz Freq. Corr. Reading Value Emission Level Limit Margin No Factor [db (uv)] [db (uv)] [db (uv)] (db) [MHz] (db) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission Level Limit value 4. Correction Factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF130923D of 27 Report Format Version 5.0.0

21 PHASE Line 2 6dB BANDWIDTH 9kHz Freq. Corr. Reading Value Emission Level Limit Margin No Factor [db (uv)] [db (uv)] [db (uv)] (db) [MHz] (db) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission Level Limit value 4. Correction Factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF130923D of 27 Report Format Version 5.0.0

22 4.3 FREQUENCY STABILITY LIMITS OF FREQUENCY STABILITY MEASUREMENT The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency over a temperature variation of 20 degrees to 50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C TEST INSTRUMENTS DESCRIPTION & MANUFACTURER MODEL NO. SERIAL NO. DATE OF CALIBRATION DUE DATE OF CALIBRATION R&S SPECTRUM ANALYZER Temperature & Humidity Chamber FSP May. 17, 2013 May. 16, 2014 MHU-225AU May 23, 2013 May 22, 2014 NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA TEST PROCEDURE a. The EUT was placed inside the environmental test chamber and powered by nominal DC voltage. b. Turn the EUT on and couple its output to a spectrum analyzer. c. Turn the EUT off and set the chamber to the highest temperature specified. d. Allow sufficient time (approximately 30 min) for the temperature of the chamber to stabilize, turn the EUT on and measure the operating frequency after 2, 5, and 10 minutes. e. Repeat step 2 and 3 with the temperature chamber set to the lowest temperature. f. The test chamber was allowed to stabilize at +20 degree C for a minimum of 30 minutes. The supply voltage was then adjusted on the EUT from 85% to 115% and the frequency record. Report No.: RF130923D of 27 Report Format Version 5.0.0

23 4.3.4 DEVIATION FROM TEST STANDARD No deviation TEST SETUP Temperature Spectrum Analyzer DC Power Supply EUT OPERATING CONDITION Same as Item Report No.: RF130923D of 27 Report Format Version 5.0.0

24 4.3.7 TEST RESULTS OPERATING FREQUENCY: 13.56MHz LIMIT: ± 0.01% TEMP. ( ) POWER SUPPLY (Vac) (MHz) (%) Note: Operating temperature of EUT is -20 degrees C to 55 degrees C. Report No.: RF130923D of 27 Report Format Version 5.0.0

25 5. PHOTOGRAPHS OF THE TEST CONFIGURATION Please refer to the attached file (Test Setup Photo). Report No.: RF130923D of 27 Report Format Version 5.0.0

26 6. INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Tel: Fax: Hsin Chu EMC/RF Lab: Tel: Fax: Hwa Ya EMC/RF/Safety Telecom Lab: Tel: Fax: Web Site: The address and road map of all our labs can be found in our web site also. Report No.: RF130923D of 27 Report Format Version 5.0.0

27 7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No modifications were made to the EUT by the lab during the test. --- END --- Report No.: RF130923D of 27 Report Format Version 5.0.0