FCC TEST REPORT. LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Linko Hsiang 244, Taipei Hsien, Taiwan, R.O.C.

Transcription

1 FCC TEST REPORT REPORT NO.: RF951204L06A MODEL NO.: WRT54G V8 RECEIVED: Jan. 13, 2007 TESTED: Jan. 13 ~ Jan. 16, 2007 ISSUED: Jan. 17, 2007 APPLICANT: Cisco-Linksys LLC ADDRESS: 121 Theory Drive Irvine, CA (USA) ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: 47, 14 th Ling, Chia Pau Tsuen, Linko Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: 19, Hwa Ya 2 nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 54 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample Report : RF951204L06A 1 Report Format Version 2.0.5

2 of Contents 1 CERTIFICATION SUMMARY OF TEST RESULTS MEASUREMENT UNCERTAINTY GENERAL INFORMATION GENERAL DESCRIPTION OF EUT DESCRIPTION OF TEST MODES CONFIGURATION OF SYSTEM UNDER TEST TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL GENERAL DESCRIPTION OF APPLIED STANDARDS DESCRIPTION OF SUPPORT UNITS TEST TYPES AND RESULTS CONDUCTED EMISSION MEASUREMENT LIMITS OF CONDUCTED EMISSION MEASUREMENT TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS RADIATED EMISSION MEASUREMENT LIMITS OF RADIATED EMISSION MEASUREMENT TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS BAND EDGES MEASUREMENT LIMITS OF BAND EDGES MEASUREMENT TEST INSTRUMENTS TEST PROCEDURE DEVIATION FROM TEST STANDARD EUT OPERATING CONDITION TEST RESULTS INFORMATION ON THE TESTING LABORATORIES...53 APPENDIX-A... A-1 Report : RF951204L06A 2 Report Format Version 2.0.5

3 1 CERTIFICATION PRODUCT : Wireless-G Broadband Router With 4-Port Switch MODEL NO.: WRT54G V8 BRAND: Linksys APPLICANT : Cisco-Linksys LLC TESTED: Jan. 13 ~ Jan. 16, 2007 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS : FCC Part 15, Subpart C (Section ), ANSI C The above equipment have been tested by Advance Data Technology Corporation, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample s EMC characteristics under the conditions specified in this report. PREPARED BY :, DATE: Jan. 17, 2007 Wendy Liao TECHNICAL ACCEPTANCE :, DATE: Jan. 17, 2007 Responsible for RF Long Chen APPROVED BY :, DATE: Jan. 17, 2007 Gary Chang / Supervisor Report : RF951204L06A 3 Report Format Version 2.0.5

4 2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C Standard Section Test Type and Result REMARK AC Power Conducted PASS Meet the requirement of limit. Minimum passing margin is 3.59dB at 0.315MHz (d) Transmitter Radiated s : PASS Meet the requirement of limit. Minimum passing margin is 1.01dB at 61.10MHz (d) Band Edge Measurement : 20 db less than the peak value of fundamental frequency PASS Meet the requirement of limit 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4: Measurement Frequency Uncertainty Conducted emissions 9kHz~30MHz 2.44 db 30MHz ~ 200MHz 3.71 db Radiated emissions 200MHz ~1000MHz 3.73 db 1GHz ~ 18GHz 2.26 db 18GHz ~ 40GHz 1.94 db This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Report : RF951204L06A 4 Report Format Version 2.0.5

5 3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT PRODUCT MODEL NO. FCC ID POWER SUPPLY MODULATION TYPE Wireless-G Broadband Router With 4-Port Switch WRT54G V8 Q87-WRT54GV8 12Vdc from AC adapter CCK, DQPSK, DBPSK for DSSS 64QAM, 16QAM, QPSK, BPSK for OFDM MODULATION TECHNOLOGY DSSS, OFDM TRANSFER RATE FREQUENCY RANGE b: 11/5.5/2/1Mbps g: 54/48/36/24/18/12/9/6Mbps 2400MHz ~ MHz NUMBER OF CHANNEL 11 MAXIMUM OUTPUT POWER ANTENNA TYPE mW Fix Dipole antenna with 2dBi gain I/O PORTS RJ 45 DATA CABLE ASSOCIATED DEVICE NA Adapter NOTE: 1. This report is issued as a supplementary report of RF951204L06. This report shall be combined together with its original report. 2. RF output power is the same as the original test report. 3. This report is prepared for FCC Class II permissive change. Difference compared with original report is listed as below, therefore Conducted and Radiated Measurements had been re-tested. ITEM ORIGINAL DESCRIPTION ITEM CLASS II CHANE DESCRIPTION 1 with two cores 1 TX: without core RX: without core TX: without core 2 RX: with one core 4. The EUT was powered by the following adapters: ADAPTER 1 BRAND: LINKSYS MODEL: D12-50-A INPUT: 120Vac, 60Hz, 100mA OUTPUT: 12Vdc, 500mA POWER CORD: DC 1.8m non-shielded cable without core Report : RF951204L06A 5 Report Format Version 2.0.5

6 ADAPTER 2 BRAND: LINKSYS MODEL: AM INPUT: 120Vac, 60Hz, 12W OUTPUT: 12Vdc, 500mA POWER CORD: DC 1.8m non-shielded cable without core ADAPTER 3 BRAND: LINKSYS MODEL: AD12V/0.5A-SW INPUT: 100~240Vac, 50/60Hz, 0.5A OUTPUT: 12Vdc, 0.5A POWER CORD: DC 1.8m non-shielded cable without core ADAPTER 4 BRAND: LINKSYS MODEL: LS120V05AE INPUT: 100~240Vac, 50/60Hz, 0.5A OUTPUT: 12Vdc, 500mA DC: 1.8m non-shielded cable without core POWER CORD: AC: 0.5m non-shielded cable without core ADAPTER 5 BRAND: LINKSYS MODEL: LS120V05A INPUT: 100~240Vac, 50/60Hz, 0.5A OUTPUT: 12Vdc, 500mA DC 1.8m non-shielded cable without core POWER CORD: AC 0.5m non-shielded cable without core 5. The EUT, operates in the 2.4GHz frequency range, lets you connect IEEE g or IEEE b devices to the network. With its high-speed data transmissions of up to 54Mbps. 6. The above EUT information was declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report : RF951204L06A 6 Report Format Version 2.0.5

7 3.2 DESCRIPTION OF TEST MODES Eleven channels are provided to this EUT. CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz CONFIGURATION OF SYSTEM UNDER TEST 100Ω Load 1.8m UTP cable x3 Printer Modem EUT Notebook 1.8m UTP cable *Test table 10m RJ45 UTP cable Notebook *Kept in a remote area Report : RF951204L06A 7 Report Format Version 2.0.5

8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL EUT APPLICABLE TO CONFIGURE MODE PLC RE<1G RE 1G APCM A1 - - A B1 B C1 - - C D1 - - D E1 - - E DESCRIPTION Power from Adapter 1 (TX: without core; RX: without core) Power from Adapter 1 (TX: without core; RX: with one core) Power from Adapter 2 (TX: without core; RX: without core) Power from Adapter 2 (TX: without core; RX: with one core ) Power from Adapter 3 (TX: without core; RX: without core) Power from Adapter 3 (TX: without core; RX: with one core) Power from Adapter 4 (TX: without core; RX: without core) Power from Adapter 4 (TX: without core; RX: with one core) Power from Adapter 5 (TX: without core; RX: without core) Power from Adapter 5 (TX: without core; RX: with one core) Where PLC: Power Line Conducted RE<1G: Radiated below 1GHz RE 1G: Radiated above 1GHz APCM: Port Conducted Measurement NOTE: - means no effect Power Line Conducted Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) A g 1 to 11 1 OFDM BPSK 6 B g 1 to 11 1 OFDM BPSK 6 C g 1 to 11 1 OFDM BPSK 6 D g 1 to 11 1 OFDM BPSK 6 E g 1 to 11 1 OFDM BPSK 6 Report : RF951204L06A 8 Report Format Version 2.0.5

9 Radiated Test (Below 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) A1 ~ A g 1 to OFDM BPSK 6 B1 ~ B g 1 to OFDM BPSK 6 C1 ~ C g 1 to OFDM BPSK 6 D1 ~ D g 1 to OFDM BPSK 6 E1 ~ E g 1 to OFDM BPSK 6 Radiated Test (Above 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) B b 1 to 11 1, 11 DSSS DBPSK 1 B g 1 to 11 1, 11 OFDM BPSK 6 Bandedge Measurement: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) B b 1 to 11 1, 11 DSSS DBPSK 1 B g 1 to 11 1, 11 OFDM BPSK 6 Report : RF951204L06A 9 Report Format Version 2.0.5

10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C. (15.247) ANSI C All test items have been performed and recorded as per the above standards. NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. 3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID 1 NOTEBOOK COMPUTER DELL PP05L E2K24CLNS 2 PRINTER EPSON LQ-300+ DCGY FCC DoC Approved 3 MODEM ACEEX 1414V/ IFAXDM NOTEBOOK COMPUTER DELL PP05L E2K24CLNS NO. 1 NA m shielded cable m shielded cable 4 NA SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS NOTE: 1. All power cords of the above support units are non shielded (1.8m). 2. Item 4 act as a communication partner to transfer data. Report : RF951204L06A 10 Report Format Version 2.0.5

11 4 TEST TYPES AND RESULTS 4.1 CONDUCTED EMISSION MEASUREMENT LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION CONDUCTED LIMIT (dbµv) Quasi-peak 66 to Average 56 to NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above TEST INSTRUMENTS DESCRIPTION & MANUFACTURER MODEL NO. SERIAL NO. CALIBRATED UNTIL Test Receiver ROHDE & SCHWARZ ESCS Sep. 25, 2007 RF signal cable Woken 5D-FB Cable-HYCO3-01 Jan. 06, 2008 LISN ROHDE & SCHWARZ ESH2-Z Jan. 08, 2008 LISN ROHDE & SCHWARZ ESH3-Z Jan. 22, 2007 Software ADT ADT_Cond_V3 NA NA NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room The VCCI Site Registration is C Report : RF951204L06A 11 Report Format Version 2.0.5

12 4.1.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. levels under - 20dB was not recorded DEVIATION FROM TEST STANDARD No deviation Report : RF951204L06A 12 Report Format Version 2.0.5

13 4.1.5 TEST SETUP Vertical G round Reference Plane Test Receiver 40cm EUT 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 from other units and other metal planes For the actual test configuration, please refer to the attached file (Test Setup Photo) EUT OPERATING CONDITIONS a. Connected the EUT to a notebook system and placed on a testing table. b. Prepared a notebook computer and placed it outside of testing area to act as communication partner for EUT. c. The notebook system ran a test program (provided by manufacturer) to enable EUT under transmission condition continuously at specific channel frequency. d. The necessary accessories enable the EUT in full functions. Report : RF951204L06A 13 Report Format Version 2.0.5

14 4.1.7 TEST RESULTS CONDUCTED WORST-CASE DATA EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 1 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz TRANSFER RATE ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz A1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 14 Report Format Version 2.0.5

15 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 2 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz TRANSFER RATE ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz A1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 15 Report Format Version 2.0.5

16 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 1 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz TRANSFER RATE ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz B1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 16 Report Format Version 2.0.5

17 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 2 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz TRANSFER RATE ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz B1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 17 Report Format Version 2.0.5

18 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 1 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz TRANSFER RATE ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz C1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 18 Report Format Version 2.0.5

19 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 2 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz C1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 19 Report Format Version 2.0.5

20 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 1 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz TRANSFER RATE ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz D1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 20 Report Format Version 2.0.5

21 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 2 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz TRANSFER RATE ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz D1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 21 Report Format Version 2.0.5

22 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 1 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz TRANSFER RATE ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz E1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 22 Report Format Version 2.0.5

23 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 1 PHASE Line 2 MODULATION TYPE BPSK 6dB BANDWIDTH 9 khz TRANSFER RATE ENVIRONMENTAL CONDITIONS 6Mbps 21deg. C, 65%RH, 991hPa INPUT POWER (SYSTEM) TEST MODE 120Vac, 60 Hz E1 TESTED BY Dean Wang Corr. Reading No [db (uv)] [db (uv)] [db (uv)] [MHz] Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. value = level - value 5. factor = Insertion loss + Cable loss 6. = + Reading. Report : RF951204L06A 23 Report Format Version 2.0.5

24 4.2 RADIATED EMISSION MEASUREMENT LIMITS OF RADIATED EMISSION MEASUREMENT s radiated outside of the specified bands, shall be according to the general radiated limits in as following: Frequencies Field strength (microvolts/meter) Measurement distance (meters) /F(kHz) /F(kHz) Above NOTE: 1. The lower limit shall apply at the transition frequencies. 2. level = 20 log level (uv/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report : RF951204L06A 24 Report Format Version 2.0.5

25 4.2.2 TEST INSTRUMENTS DESCRIPTION & MANUFACTURER Test Receiver ROHDE & SCHWARZ Spectrum Analyzer ROHDE & SCHWARZ BILOG SCHWARZBECK HORN SCHWARZBECK HORN SCHWARZBECK Preamplifier Agilent Preamplifier Agilent RF signal cable HUBER+SUHNNER RF signal cable HUBER+SUHNNER Software ADT. Tower inn-co GmbH Tower Controller inn-co GmbH Turn ADT. Turn Controller ADT. MODEL NO. SERIAL NO. CALIBRATED UNTIL ESI May 22, 2007 FSP Oct. 05, 2007 VULB May 31, D 9120D-209 Jan. 27, 2007 BBHA 9170 BBHA Dec. 28, D 2944A10633 Oct. 26, B 3008A01964 Oct. 26, 2007 SUCOFLEX /4 Feb. 14, 2007 SUCOFLEX /4 Nov. 14, 2007 ADT_Radiated_V7.6 NA NA MA NA CO NA TT100. TT NA SC100. SC NA NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The VCCI Site Registration is R The IC Site Registration is IC Report : RF951204L06A 25 Report Format Version 2.0.5

26 4.2.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meters semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and video bandwidth is 3MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 10Hz for Average detection (AV) at frequency above 1GHz DEVIATION FROM TEST STANDARD No deviation Report : RF951204L06A 26 Report Format Version 2.0.5

27 4.2.5 TEST SETUP For the actual test configuration, please refer to the attached file (Test Setup Photo) EUT OPERATING CONDITIONS Same as Report : RF951204L06A 27 Report Format Version 2.0.5

28 4.2.7 TEST RESULTS RADIATED WORST-CASE DATA: BELOW 1GHz EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS BPSK 6Mbps 25deg. C, 68%RH, 991hPa FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz A1 TESTED BY Morgan Chen ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 28 Report Format Version 2.0.5

29 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS BPSK 6Mbps 24deg. C, 62%RH, 991hPa MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz A2 TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) QP V QP V QP V QP V QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 29 Report Format Version 2.0.5

30 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS BPSK 6Mbps 25deg. C, 68%RH, 991hPa MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz B1 TESTED BY Morgan Chen ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 30 Report Format Version 2.0.5

31 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS BPSK 6Mbps 24deg. C, 62%RH, 991hPa MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz B2 TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) QP V QP V QP V QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 31 Report Format Version 2.0.5

32 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS BPSK 6Mbps 25deg. C, 68%RH, 991hPa MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz C1 TESTED BY Morgan Chen ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 32 Report Format Version 2.0.5

33 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS BPSK 6Mbps 24deg. C, 62%RH, 991hPa MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz C2 TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) QP V QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 33 Report Format Version 2.0.5

34 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS BPSK 6Mbps 25deg. C, 68%RH, 991hPa MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz D1 TESTED BY Morgan Chen ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (Db/m) QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 34 Report Format Version 2.0.5

35 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS BPSK 6Mbps 24deg. C, 62%RH, 991hPa MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz D2 TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) QP V QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 35 Report Format Version 2.0.5

36 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS TESTED BY BPSK 6Mbps 25deg. C, 68%RH, 991hPa Morgan Chen MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz E1 ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 36 Report Format Version 2.0.5

37 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE ENVIRONMENTAL CONDITIONS TESTED BY BPSK 6Mbps 24deg. C, 62%RH, 991hPa Match Tsui MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION INPUT POWER (SYSTEM) TEST MODE Below 1000MHz Quasi-Peak 120Vac, 60 Hz E2 ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) QP H QP H QP H QP H QP H QP H QP H QP H QP H QP H QP H QP H QP H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) QP V QP V QP V QP V QP V QP V QP V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. Report : RF951204L06A 37 Report Format Version 2.0.5

38 802.11b DSSS MODULATION EUT TEST CONDITION CHANNEL Channel 1 MODULATION TYPE TRANSFER RATE INPUT POWER (SYSTEM) DBPSK 1Mbps MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS 1 ~ 25GHz Peak(PK) Average (AV) 24deg. C, 62%RH, 991hPa 120Vac, 60 Hz TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) PK H AV H PK H AV H * PK 1.38 H * AV 1.38 H PK H AV H PK H AV H PK H AV H PK H AV H REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. 5. * : Fundamental frequency. Report : RF951204L06A 38 Report Format Version 2.0.5

39 EUT TEST CONDITION CHANNEL Channel 1 MODULATION TYPE TRANSFER RATE INPUT POWER (SYSTEM) DBPSK 1Mbps MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS 1 ~ 25GHz Peak(PK) Average (AV) 24deg. C, 62%RH, 991hPa 120Vac, 60 Hz TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) PK V AV V PK V AV V * PK 1.05 V * AV 1.05 V PK V AV V PK V AV V PK V AV V PK V AV V PK V AV V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. 5. * : Fundamental frequency. Report : RF951204L06A 39 Report Format Version 2.0.5

40 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE INPUT POWER (SYSTEM) DBPSK 1Mbps MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS 1 ~ 25GHz Peak(PK) Average (AV) 24deg. C, 62%RH, 991hPa 120Vac, 60 Hz TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) PK H AV H * PK 1.59 H * AV 1.59 H PK H AV H PK H AV H PK H AV H PK H AV H REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. 5. * : Fundamental frequency. Report : RF951204L06A 40 Report Format Version 2.0.5

41 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE INPUT POWER (SYSTEM) DBPSK 1Mbps MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS 1 ~ 25GHz Peak(PK) Average (AV) 24deg. C, 62%RH, 991hPa 120Vac, 60 Hz TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V PK V AV V PK V AV V PK V AV V PK V AV V PK V AV V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. 5. * : Fundamental frequency. Report : RF951204L06A 41 Report Format Version 2.0.5

42 802.11g OFDM MODULATION EUT TEST CONDITION CHANNEL Channel 1 MODULATION TYPE TRANSFER RATE INPUT POWER (SYSTEM) BPSK 6Mbps MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS 1 ~ 25GHz Peak(PK) Average (AV) 24deg. C, 62%RH, 991hPa 120Vac, 60 Hz TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) PK H AV H PK H AV H * PK 1.21 H * AV 1.21 H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) PK V AV V PK V AV V * PK 1.01 V * AV 1.01 V PK V AV V PK V AV V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. 5. * : Fundamental frequency. Report : RF951204L06A 42 Report Format Version 2.0.5

43 EUT TEST CONDITION CHANNEL Channel 11 MODULATION TYPE TRANSFER RATE INPUT POWER (SYSTEM) BPSK 6Mbps MEASUREMENT DETAIL FREQUENCY RANGE DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS 1 ~ 25GHz Peak(PK) Average (AV) 24deg. C, 62%RH, 991hPa 120Vac, 60 Hz TESTED BY Match Tsui ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M (db/m) PK H AV H * PK 1.18 H * AV 1.18 H PK H AV H PK H AV H PK H AV H ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M (db/m) PK V AV V * PK 1.00 V * AV 1.00 V PK V AV V PK V AV V PK V AV V REMARKS: 1. level= + (db/m) 2. (db/m) = (db/m) + Cable 3. The other emission levels were very low against the limit. 4. value = level value. 5. * : Fundamental frequency. Report : RF951204L06A 43 Report Format Version 2.0.5