SPORTON International Inc.

Transcription

1 SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: / FAX: / CE RADIO TEST REPORT Applicant s company Applicant Address Ralink Technology Corporation 5F., No.36, Taiyuan St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. Manufacturer s company Manufacturer Address Ralink Technology Corporation 5F., No.36, Taiyuan St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. Product Name Brand Name Model Name b/g/n 1T1R combo card Ralink RT3090BC4 Test Standard(s) ETSI EN V1.7.1 ( ) Test Freq. Range 2400 ~ MHz Received Date Nov. 15, 2009 Final Test Date Jan. 01, 2010 Submission Type Existing Change Statement Test result included in this report is only for the Draft n and the b/g part of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ETSI EN V1.7.1 ( ). The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report Format Version: 02

2 Table of Contents 1. CERTIFICATE OF COMPLIANCE SUMMARY OF THE TEST RESULT GENERAL INFORMATION Product Details Medium Access Protocol Accessories Table for Filed Antenna Table for Carrier Frequencies Table for Test Modes Table for Testing Locations Table for Supporting Units Table for Parameters of Test Software Setting Test Configurations TEST RESULT Equivalent Isotropic Radiated Power Measurement Maximum Spectral Power Density Measurement Frequency Range Measurement Transmitter Spurious Emissions Measurement Receiver Spurious Emissions Measurement LIST OF MEASURING EQUIPMENTS TEST LOCATION APPENDIX A. PHOTOGRAPHS OF EUT...A1 ~ A20 APPENDIX B. TEST PHOTOS... B1 ~ B5 APPENDIX C. ANTENNA LIST Report Format Version: 02 Page No. : i of ii

3 History of This Test Report Original Issue Date: Jan. 18, 2010 Report No.: ER9D AA No additional attachment. Additional attachment were issued as following record: Attachment No. Issue Date Description ER9D0210AA Dec. 08, 2009 Add two higher gain antennas, so all the test items were tested and recorded in the report Report Format Version: 02 Page No. : ii of ii

4

5 2. SUMMARY OF THE TEST RESULT Applied Standard: ETSI EN V1.7.1 ( ) Part Standard Clause Description of Test Result Under Limit Equivalent Isotropic Radiated Power Complies 0.04 db Power Spectral Density Complies 0.14 db Frequency Range Complies Transmitter Spurious Emissions Complies db Receiver Spurious Emissions Complies 0.01 db Test Items Uncertainty Remark Equivalent Isotropic Radiated Power (Conducted) ±0.8dB Confidence levels of 95% Power Spectral Density (Conducted) ±1.0dB Confidence levels of 95% Frequency Range ± Confidence levels of 95% Spurious Emissions 30MHz~1000MHz (Radiated) ±2.6dB Confidence levels of 95% Spurious Emissions 1GHz~18GHz (Radiated) ±2.6dB Confidence levels of 95% Temperature ±0.7 Confidence levels of 95% Humidity ±3.2% Confidence levels of 95% DC / AC Power Source ±1.4% Confidence levels of 95% Report Format Version: 02 Page No. : 2 of 113

6 3. GENERAL INFORMATION 3.1. Product Details Draft n Items Description Product Type Radio Type Power Type Modulation Data Modulation Data Rate (Mbps) Frequency Range Channel Number EIRP Output Power WLAN (1TX, 1RX) Intentional Transceiver From host system see the below table for Draft n OFDM (BPSK / QPSK / 16QAM / 64QAM) see the below table for Draft n 2400 ~ MHz 13 for 20MHz bandwidth ; 9 for 40MHz bandwidth MCS0(20MHz) : dbm ; MCS0(40MHz) : dbm Carrier Frequencies Please refer to section 3.5 Antenna Please refer to section b/g Items Description Product Type Radio Type Power Type WLAN (1TX, 1RX) Intentional Transceiver From host system Modulation DSSS for IEEE b ; OFDM for IEEE g Data Modulation DSSS (BPSK / QPSK / CCK) ; OFDM (BPSK / QPSK / 16QAM / 64QAM) Data Rate (Mbps) DSSS (1/ 2/ 5.5/11) ; OFDM (6/9/12/18/24/36/48/54) Frequency Band 2400 ~ MHz Channel Number 13 EIRP Output Power 11b: dbm ; 11g: dbm Carrier Frequencies Please refer to section 3.5 Antenna Please refer to section 3.4 Antenna & Band width Antenna Single (TX) Band width Mode 20 MHz 40 MHz b V X g V X Draft n V V Report Format Version: 02 Page No. : 3 of 113

7 Draft n spec MCS Index Nss Modulation R NBPSC NCBPS NDBPS 800nsGI Datarate(Mbps) 400nsGI 20MHz 40MHz 20MHz 40MHz 20MHz 40MHz 20MHz 40MHz 0 1 BPSK 1/ QPSK 1/ QPSK 3/ QAM 1/ QAM 3/ QAM 2/ QAM 3/ QAM 5/ BPSK 1/ QPSK 1/ QPSK 3/ QAM 1/ QAM 3/ QAM 2/ QAM 3/ QAM 5/ Symbol NSS R NBPSC NCBPS NDBPS GI Explanation Number of spatial streams Code rate Number of coded bits per single carrier Number of coded bits per symbol Number of data bits per symbol guard interval 3.2. Medium Access Protocol DUT s medium access protocol has be implemented standard ensures that all stations, both radio-based network interface cards (NICs) and access points, implement access methods for sharing the air medium. The medium access protocols makes it mandatory that all stations implement the DCF, a form of carrier sense multiple access with collision avoidance (CSMA/CA). CSMA is a contention-based protocol making certain that all stations first sense the medium before transmitting. The main goal is to avoid having stations transmit at the same time, which results in collisions and corresponding retransmissions. Report Format Version: 02 Page No. : 4 of 113

8 3.3. Accessories Others There are two antennas with two cores in the end side. The core brand is King core (K5B RH 9*8*5) Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dbi) Remark A JOYMAX IWX-145XRSXX-999 Dipole Antenna Reversed-SMA 3.7 TX/RX B ACON APP6P PIFA Antenna I-PEX 3.5 TX/RX Note: There are four types of EUT, the difference of each type as following description: EUT 1. Two antenna connectors with two crystals EUT 2. Two antenna connectors with one crystal EUT 3. One antenna connector with two crystals EUT 4. One antenna connector with one crystal After pre-testing, EUT 1 generated the worst test result, so it was recorded in the report. There are two sizes of EUT. One is full size (with PCB extend card), and another is half size (without PCB extend card). But their internal structures are identical. So only full size of EUT was tested and recorded in the report. All the detail antenna information, please refer to Appendix C for further information. Due to Ant. A and B mentioned above are the highest gain value among two different types, only ant A and B were tested and recorded in this test report. The EUT supports the antenna with TX/RX diversity function for WLAN and Bluetooth. When Connector 1 is WLAN function, Connector 2 must be Bluetooth function. Oppositely, if Connector 2 is WLAN function, Connector 1 must be Bluetooth function. Report Format Version: 02 Page No. : 5 of 113

9 Connector 1: TX/RX Connector 2: TX/RX 3.5. Table for Carrier Frequencies There are two bandwidth systems for Draft n. For both 20MHz bandwidth systems, use Channel 1~Channel 13. For both 40MHz bandwidth systems, use Channel 3~Channel 11. Freqeuncy Band Channel No. Frequency Channel No. Frequency MHz MHz MHz MHz MHz MHz 2400~2483.5MHz MHz MHz MHz MHz MHz MHz MHz Report Format Version: 02 Page No. : 6 of 113

10 3.6. Table for Test Modes Preliminary tests were performed in different data rate to find the worst radiated emission. The data rate shown in the table below is the worst-case rate with respect to the specific test item. Investigation has been done on all the possible configurations for searching the worst cases. The following table is a list of the test modes shown in this test report. Test Items Mode Data Rate Channel Antenna Equivalent Isotropic Radiated Power Power Spectral Density 11b/BPSK 1 Mbps 1/7/13 A+B 11g/BPSK 6 Mbps 1/7/13 A+B MCS0/20MHz 6.5 Mbps 1/7/13 A+B MCS0/40MHz 13.5 Mbps 3/7/11 A+B Frequency Range 11b/BPSK 1 Mbps 1/13 A+B 11g/BPSK 6 Mbps 1/13 A+B MCS0/20MHz 6.5 Mbps 1/13 A+B MCS0/40MHz 13.5 Mbps 3/11 A+B Transmitter Spurious Emissions 11g/BPSK 6 Mbps 1/13 A+B (30MHz~1GHz) MCS0/40MHz 27 Mbps 3/11 A+B Transmitter Spurious Emissions (1GHz~12.75GHz) 11b/BPSK 1 Mbps 1/13 A+B 11g/BPSK 6 Mbps 1/13 A+B MCS0/20MHz 6.5 Mbps 1/13 A+B MCS0/40MHz 13.5 Mbps 3/11 A+B Receiver Spurious Emissions 11g/BPSK - 1/13 A+B (30MHz~1GHz) MCS0/40MHz - 3/11 A+B Receiver Spurious Emissions 11g/BPSK - 1/13 A+B (1GHz~12.75GHz) MCS0/40MHz - 3/11 A+B Note: The product is restricted for indoor use only. The following test modes were performed for all tests: Mode 1. EUT 1 with Dipole Antenna Mode 2. EUT 1 with PIFA Antenna 3.7. Table for Testing Locations Test Site No. Site Category Location Test Site No. Site Category Location 05CH01-HY FAC Hwa Ya TH01-HY OVEN Room Hwa Ya Open Area Test Site (OATS); Semi Anechoic Chamber (SAC); Fully Anechoic Chamber (FAC). Please refer section 6 for Test Site Address. Report Format Version: 02 Page No. : 7 of 113

11 3.8. Table for Supporting Units Support Unit Brand Model FCC ID Notebook DELL M1330 PPD-AR5BXB Table for Parameters of Test Software Setting During testing, Channel & Power Controlling Software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product. <For Antenna A> Power Parameters of Draft n Test Software Version QA Frequency 2412 MHz 2442 MHz 2472 MHz MCS0 20MHz Frequency 2422 MHz 2442 MHz 2462 MHz MCS0 40MHz Power Parameters of IEEE b/g Test Software Version QA Frequency 2412MHz 2442MHz 2472MHz IEEE b 10 0F 0F IEEE g <For Antenna B> Power Parameters of Draft n Test Software Version QA Frequency 2412 MHz 2442 MHz 2472 MHz MCS0 20MHz Frequency 2422 MHz 2442 MHz 2462 MHz MCS0 40MHz Power Parameters of IEEE b/g Test Software Version QA Frequency 2412MHz 2442MHz 2472MHz IEEE b F IEEE g Report Format Version: 02 Page No. : 8 of 113

12 3.10. Test Configurations Test Mode: Mode 1 AC Main 1 ANT ANT RJ-11 DC VGA PS/2 LPT RJ-45 Notebook USB x 2 EUT POWER CABLE, 260 CM, NON-SHIELDED 2. ANT CABLE, 19 CM, SHIELDED Test Mode: Mode 2 AC Main 1 ANT ANT RJ-11 DC VGA PS/2 LPT RJ-45 Notebook USB x 2 EUT POWER CABLE, 260 CM, NON-SHIELDED 2. ANT CABLE, 22 CM, SHIELDED Report Format Version: 02 Page No. : 9 of 113

13 4. TEST RESULT 4.1. Equivalent Isotropic Radiated Power Measurement Limit The equivalent isotropic radiated power is defined as the total power of the transmitter. The equivalent isotropic radiated power shall be equal to or less than -10dBW (100 mw) e.i.r.p. This limit shall apply for any combination of power level and intended antenna assembly Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the power meter. Power Meter Parameter Filter No. Measurement time Used Average Sensor Setting Auto s ~ 26 s NRV-Z Test Procedures 1. Since a temporary antenna connector can be attached on the RF output port, so conducted measurement method was used in this case. 2. A wide band power meter with a matched thermocouple detector was used to directly measure the output power from the RF output port of the EUT in continuously transmitting mode. 3. The EIRP = A+G+10*log(1/x), where A is the power measured in (2), G is the gain of the antenna of the EUT in dbi and x is the duty cycle of the EUT in continuously transmitting mode. 4. The measurement shall be repeated at the lowest, the middle, and the highest channel of the stated frequency range. These measurements shall also be performed at normal and extreme test conditions Test Setup Layout Test Deviation There is no deviation with the original standard. Report Format Version: 02 Page No. : 10 of 113

14 EUT Operation during Test The EUT was programmed to be in continuously transmitting mode Test Result <For Antenna A> Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations Draft n Test Date Dec. 30, 2009 Configuration Draft n MCS0 20MHz Ant. A Test Conditions Average EIRP Power ( dbm ) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 V max (V) V min (V) V max (V) T max ( C) 35 V min (V) Max Peak Power Limits Result 20dBm (-10dBW) Complies Configuration Draft n MCS0 40MHz Ant. A Test Conditions Average EIRP Power ( dbm ) CH 3 CH 7 CH 11 T nom ( C) 20 V nom (V) T min ( C) 0 V max (V) V min (V) V max (V) T max ( C) 35 V min (V) Max Peak Power Limits Result 20dBm (-10dBW) Complies Report Format Version: 02 Page No. : 11 of 113

15 Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations b/g Test Date Dec. 30, 2009 Configuration IEEE b Ant. A Test Conditions Average EIRP mean power (dbm) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Max mean Power Limits Result 20dBm (-10dBW) Complies Configuration IEEE g Ant. A Test Conditions Average EIRP mean power (dbm) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Max mean Power Limits Result 20dBm (-10dBW) Complies Report Format Version: 02 Page No. : 12 of 113

16 <For Antenna B> Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations Draft n Test Date Dec. 30, 2009 Configuration Draft n MCS0 20MHz Ant. B Test Conditions Average EIRP Power ( dbm ) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 V max (V) V min (V) V max (V) T max ( C) 35 V min (V) Max Peak Power Limits Result 20dBm (-10dBW) Complies Configuration Draft n MCS0 40MHz Ant. B Test Conditions Average EIRP Power ( dbm ) CH 3 CH 7 CH 11 T nom ( C) 20 V nom (V) T min ( C) 0 V max (V) V min (V) V max (V) T max ( C) 35 V min (V) Max Peak Power Limits Result 20dBm (-10dBW) Complies Report Format Version: 02 Page No. : 13 of 113

17 Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations b/g Test Date Dec. 30, 2009 Configuration IEEE b Ant. B Test Conditions Average EIRP mean power (dbm) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Max mean Power Limits Result 20dBm (-10dBW) Complies Configuration IEEE g Ant. B Test Conditions Average EIRP mean power (dbm) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Max mean Power Limits Result 20dBm (-10dBW) Complies Report Format Version: 02 Page No. : 14 of 113

18 4.2. Maximum Spectral Power Density Measurement Limit The maximum spectral power density is defined as the highest level of power in Watts per Hertz generated by the transmitter within the power envelope. For wide band modulations other than FHSS (e.g. DSSS, OFDM, etc.), the maximum spectrum power density is limited to 10 mw per MHz e.i.r.p Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer and power meter. Spectrum Analyzer Attenuation Span Frequency RB VB Detector Trace Sweep Time Setting 20~30dB 0 MHz 1 MHz 1 MHz Positive Peak Max Hold Auto Power Meter Parameter Filter No. Measurement time Used Average Sensor Setting Auto s ~ 26 s NRV-Z Test Procedures 1. Pre-calibration for the spectrum analyzer has to be done first through a CW signal of the measured carrier frequency with 10dBm power strength. 2. A power meter is connected on the IF output port of the spectrum analyzer. 3. Adjust the spectrum analyzer to have the center frequency the same with the measured carrier. RBW=VBW=1MHz, detector mode is positive peak. Turn off the averaging function and use zero span. 4. The calibrating signal power shall be reduced to 0 dbm and it shall be verified that the power meter reading also reduces by 10 db. 5. Connect the equipment to be measured. Using the following settings of the spectrum analyzer in combination with "max hold" function, find the frequency of highest power output in the power envelope: center frequency equal to operating frequency; RBW & VBW: 1 MHz; detector mode: positive peak; averaging: off; span: 3 times the spectrum width; amplitude: adjust for middle of the instrument's range. The frequency found shall be recorded. Report Format Version: 02 Page No. : 15 of 113

19 6. Set the center frequency of the spectrum analyzer to the found frequency and switch to zero span. The power meter indicates the measured power density (D). The maximum spectral power density e.i.r.p. is calculated from the above measured power density (D), the observed duty cycle factor(x), and the applicable antenna assembly gain "G" in dbi, according to the formula: PD = D + G + 10 log (1/x). 7. The measurement shall be repeated at the lowest, the middle, and the highest channel of the stated frequency range Test Setup Layout Test Deviation There is no deviation with the original standard EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: 02 Page No. : 16 of 113

20 Test Result <For Antenna A> Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations Draft n Test Date Dec. 30, 2009 Configuration Draft n MCS0 20MHz Ant. A Test Conditions Maximum EIRP Spectral Power Density ( dbm / MHz ) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Configuration Draft n MCS0 40MHz Ant. A Test Conditions Maximum EIRP Spectral Power Density ( dbm / MHz ) CH 3 CH 7 CH 11 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Report Format Version: 02 Page No. : 17 of 113

21 Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations b/g Test Date Dec. 30, 2009 Configuration IEEE b Ant. A Test Conditions Maximum EIRP Spectral Power Density (dbm / MHz) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Configuration IEEE g Ant. A Test Conditions Maximum EIRP Spectral Power Density (dbm / MHz) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Report Format Version: 02 Page No. : 18 of 113

22 <For Antenna B> Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations Draft n Test Date Dec. 30, 2009 Configuration Draft n MCS0 20MHz Ant. B Test Conditions Maximum EIRP Spectral Power Density ( dbm / MHz ) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Configuration Draft n MCS0 40MHz Ant. B Test Conditions Maximum EIRP Spectral Power Density ( dbm / MHz ) CH 3 CH 7 CH 11 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Report Format Version: 02 Page No. : 19 of 113

23 Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations b/g Test Date Dec. 30, 2009 Configuration IEEE b Ant. B Test Conditions Maximum EIRP Spectral Power Density (dbm / MHz) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Configuration IEEE g Ant. B Test Conditions Maximum EIRP Spectral Power Density (dbm / MHz) CH 1 CH 7 CH 13 T nom ( C) 20 V nom (V) Limits Result 10dBm / MHz Complies Report Format Version: 02 Page No. : 20 of 113

24 4.3. Frequency Range Measurement Limit The frequency range of the equipment is determined by the lowest and highest frequencies occupied by the power envelope. fh is the highest frequency of the power envelope: it is the frequency furthest above the frequency of maximum power where the output power drops below the level of -80 dbm/hz e.i.r.p. spectral power density (-30 dbm if measured in a 100 khz bandwidth). fl is the lowest frequency of the power envelope; it is the frequency furthest below the frequency of maximum power where the output power drops below the level equivalent to -80 dbm/hz e.i.r.p. spectral power density (or -30 dbm if measured in a 100 khz bandwidth). The frequency range is determined by the lowest value of fl and the highest value of fh resulting from the adjustment of the equipment to the lowest and highest operating frequencies. For all equipment, the frequency range shall lie within the band 2.4 GHz to GHz (fl > 2.4 GHz and fh < GHz) Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of Spectrum Analyzer. Spectrum Analyzer Attenuation Span Frequency RB VB Detector Trace Setting 20~30dB 40MHz 100 khz 100 khz Average Average 50 sweeps Test Procedures 1. The transmitter output (antenna port) was connected to the spectrum analyzer. 2. Added [x] dbi of antenna gain was on the spectrum analyzer. 3. Place the spectrum analyzer in detector averaging mode with a minimum of 50 sweeps selected and activate transmitter with modulation applied. 4. Select lowest operating frequency of the equipment under test. 5. Find lowest frequency below the operating frequency at which spectral power density drops below -80 dbm/hz e.i.r.p. (-30 dbm if measured in a 100 khz bandwidth). This frequency shall be recorded (f L ). 6. Select the highest operating frequency of the equipment under test. 7. Find the highest frequency at which the spectral power density drops below-80 dbm/hz e.i.r.p. (-30 dbm if measured in a 100 khz bandwidth). This frequency shall be recorded (f H ). 8. These measurements shall also be performed at normal and extreme test conditions. Report Format Version: 02 Page No. : 21 of 113

25 Test Setup Layout Test Deviation There is no deviation with the original standard EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: 02 Page No. : 22 of 113

26 Test Result <For Antenna A> Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations Draft n Test Date Dec. 30, 2009 Configuration Draft n MCS0 20MHz Ant. A Test Conditions Frequency range ( MHz ) f L CH 1 f H CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 V max (V) V min (V) V max (V) T max ( C) 35 V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Configuration Draft n MCS0 40MHz Ant. A Test Conditions Frequency range ( MHz ) f L CH 3 f H CH 11 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Report Format Version: 02 Page No. : 23 of 113

27 Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations b/g Test Date Dec. 30, 2009 Configuration IEEE b Ant. A Test Conditions Frequency range (MHz) f L CH 1 f H CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Configuration IEEE g Ant. A Test Conditions Frequency range (MHz) f L CH 1 f H CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Report Format Version: 02 Page No. : 24 of 113

28 <For Antenna B> Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations Draft n Test Date Dec. 30, 2009 Configuration Draft n MCS0 20MHz Ant. B Test Conditions Frequency range ( MHz ) f L CH 1 f H CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 V max (V) V min (V) V max (V) T max ( C) 35 V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Configuration Draft n MCS0 40MHz Ant. B Test Conditions Frequency range ( MHz ) f L CH 3 f H CH 11 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Report Format Version: 02 Page No. : 25 of 113

29 Temperature 23 Humidity 56% Test Engineer Jacky Ho Configurations b/g Test Date Dec. 30, 2009 Configuration IEEE b Ant. B Test Conditions Frequency range (MHz) f L CH 1 f H CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Configuration IEEE g Ant. B Test Conditions Frequency range (MHz) f L CH 1 f H CH 13 T nom ( C) 20 V nom (V) T min ( C) 0 T max ( C) 35 V max (V) V min (V) V max (V) V min (V) Min. f L / Max. f H Band Edges Limits f L > MHz f H < MHz Result Complies Report Format Version: 02 Page No. : 26 of 113

30 4.4. Transmitter Spurious Emissions Measurement Limit Transmitter spurious emissions are emissions outside the frequency range(s) of the equipment as defined in 2.4~2.4835GHz when the equipment is in Transmit mode and/or in Standby mode. The spurious emissions of the transmitter shall not exceed the values in tables 1 and 2 in the indicated bands. Table 1 Transmitter limits for narrowband spurious emissions Frequency Range (MHz) Transmit Mode (dbm) Standby Mode (dbm) 30~ ~ ~1900 / 5150~ Table 2 Transmitter limits for wideband spurious emissions Frequency Range (MHz) Transmit Mode (dbm/hz) Standby Mode (dbm/hz) 30~ ~ ~1900 / 5150~ Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer. Spectrum Analyzer Attenuation Start Frequency Stop Frequency Detector Span Sweep Time RB / VB Setting Auto 30 MHz MHz Positive Peak 100 MHz 1s 100 khz / 30 khz Report Format Version: 02 Page No. : 27 of 113

31 Test Procedures 1. The EUT was placed on the top of the turntable in fully anechoic chamber. 2. The test shall be made in the transmitting mode. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. This measurement shall be repeated with the transmitter in standby mode where applicable. 4. For 30~1000MHz spurious emissions measurement, the broad band bi-log receiving antenna was placed 3 meters far away from the turntable. For 1~12.75GHz measurement, the receiving Horn antenna was placed 1.5 meters far away from the turntable. 5. The broadband receiving antenna was fixed on the same height with the EUT to find each suspected emissions of both horizontal and vertical polarization. Each recorded suspected value is indicated as Read Level (Raw). 6. Replace the EUT by standard antenna and feed the RF port by signal generator. 7. Adjust the frequency of the signal generator to the suspected emission and slightly rotate the turntable to locate the position with maximum reading. 8. Adjust the power level of the signal generator to reach the same reading with Read Level (Raw). 9. The level of the spurious emission is the power level of (8) plus the gain of the standard antenna in dbi and minus the loss of the cable used between the signal generator and the standard antenna. 10. If the level calculated in (9) is higher than limit by more than 6dB, then lower the RBW of the spectrum analyzer to 30KHz. If the level of this emission does not change by more than 2dB, then it is taken as narrowband emission, otherwise, wideband emission. 11. The measurement shall be repeated at the lowest and the highest channel of the stated frequency range. Report Format Version: 02 Page No. : 28 of 113

32 Test Setup Layout Test Deviation There is no deviation with the original standard EUT Operation during Test The EUT was programmed to be in continuously transmitting mode Results of Standby Mode Spurious Emissions In the initial investigation on standby mode and receiving mode, no significant differences in spurious emissions were observed between these 2 modes. Therefore, test data for standby mode was omitted in this section. Report Format Version: 02 Page No. : 29 of 113

33 Results of Transmitter Spurious Emissions Below 1GHz <For Antenna A> Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n 40MHz CH 3 / Mode 1 / Ant. A Horizontal Report Format Version: 02 Page No. : 30 of 113

34 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 31 of 113

35 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n 40MHz CH11 / Mode 1 / Ant. A Horizontal Report Format Version: 02 Page No. : 32 of 113

36 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 33 of 113

37 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH 1 / Mode 1 / Ant. A Horizontal Report Format Version: 02 Page No. : 34 of 113

38 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 35 of 113

39 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH13 / Mode 1 / Ant. A Horizontal Report Format Version: 02 Page No. : 36 of 113

40 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 37 of 113

41 <For Antenna B> Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n 40MHz CH 3 / Mode 2 / Ant. B Horizontal Report Format Version: 02 Page No. : 38 of 113

42 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 39 of 113

43 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n 40MHz CH11 / Mode 2 / Ant. B Horizontal Report Format Version: 02 Page No. : 40 of 113

44 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 41 of 113

45 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH 1 / Mode 2 / Ant. B Horizontal Report Format Version: 02 Page No. : 42 of 113

46 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 43 of 113

47 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH13 / Mode 2 / Ant. B Horizontal Report Format Version: 02 Page No. : 44 of 113

48 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 45 of 113

49 Results of Transmitter Spurious Emissions Above 1GHz <For Antenna A> Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 20MHz Ch 1 / Ant. A Horizontal Report Format Version: 02 Page No. : 46 of 113

50 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 47 of 113

51 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 20MHz Ch 13 / Ant. A Horizontal Report Format Version: 02 Page No. : 48 of 113

52 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 49 of 113

53 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 40MHz Ch 3 / Ant. A Horizontal Report Format Version: 02 Page No. : 50 of 113

54 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 51 of 113

55 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 40MHz Ch 11 / Ant. A Horizontal Report Format Version: 02 Page No. : 52 of 113

56 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 53 of 113

57 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations b CH 1 / Ant. A Horizontal Report Format Version: 02 Page No. : 54 of 113

58 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 55 of 113

59 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations b CH13 / Ant. A Horizontal Report Format Version: 02 Page No. : 56 of 113

60 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 57 of 113

61 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g Ch 1 / Ant. A Horizontal Report Format Version: 02 Page No. : 58 of 113

62 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 59 of 113

63 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH 13 / Ant. A Horizontal Report Format Version: 02 Page No. : 60 of 113

64 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 61 of 113

65 <For Antenna B> Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 20MHz Ch 1 / Ant. B Horizontal Report Format Version: 02 Page No. : 62 of 113

66 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 63 of 113

67 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 20MHz Ch 13 / Ant. B Horizontal Report Format Version: 02 Page No. : 64 of 113

68 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 65 of 113

69 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 40MHz Ch 3 / Ant. B Horizontal Report Format Version: 02 Page No. : 66 of 113

70 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 67 of 113

71 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 40MHz Ch 11 / Ant. B Horizontal Report Format Version: 02 Page No. : 68 of 113

72 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 69 of 113

73 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations b CH 1 / Ant. B Horizontal Report Format Version: 02 Page No. : 70 of 113

74 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 71 of 113

75 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations b CH13 / Ant. B Horizontal Report Format Version: 02 Page No. : 72 of 113

76 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 73 of 113

77 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g Ch 1 / Ant. B Horizontal Report Format Version: 02 Page No. : 74 of 113

78 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 75 of 113

79 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH 13 / Ant. B Horizontal Report Format Version: 02 Page No. : 76 of 113

80 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 77 of 113

81 4.5. Receiver Spurious Emissions Measurement Limit Receiver spurious emissions are emissions at any frequency when the equipment is in received mode. The spurious emissions of the reviver shall not exceed the values in tables 1 and 2 in the indicated bands. Table 1 Receiver limits for narrowband spurious emissions Frequency Range (MHz) Limit (dbm) 30~ ~ Table 2 Receiver limits for wideband spurious emissions Frequency Range (MHz) Limit (dbm) 30~ ~ Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer. Spectrum Analyzer Attenuation Start Frequency Stop Frequency Detector Span Sweep Time RB / VB Setting Auto 30 MHz MHz Positive Peak 100 MHz 1s 100 khz / 30 khz Test Procedures 1. The EUT was placed on the top of the turntable in fully anechoic chamber. 2. The test shall be made in the receiving mode. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. For 30~1000MHz spurious emissions measurement, the broad band bi-log receiving antenna was placed 3 meters far away from the turntable. For 1~12.75GHz measurement, the receiving Horn antenna was placed 1.5 meters far away from the turntable. 4. The broadband receiving antenna was fixed on the same height with the EUT to find each suspected emissions of both horizontal and vertical polarization. Each recorded suspected value is indicated as Read Level (Raw). 5. Replace the EUT by standard antenna and feed the RF port by signal generator. Report Format Version: 02 Page No. : 78 of 113

82 6. Adjust the frequency of the signal generator to the suspected emission and slightly rotate the turntable to locate the position with maximum reading. 7. Adjust the power level of the signal generator to reach the same reading with Read Level (Raw). 8. The level of the spurious emission is the power level of (7) plus the gain of the standard antenna in dbi and minus the loss of the cable used between the signal generator and the standard antenna. 9. The measurement shall be repeated at the lowest and the highest channel of the stated frequency range Test Setup Layout Test Deviation There is no deviation with the original standard EUT Operation during Test The EUT was programmed to be in continuously receiving mode. Report Format Version: 02 Page No. : 79 of 113

83 Results of Receiver Spurious Emissions Below 1GHz <For Antenna A> Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n 40MHz CH 3 / Ant. A Horizontal Report Format Version: 02 Page No. : 80 of 113

84 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 81 of 113

85 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n 40MHz CH 11 / Ant. A Horizontal Report Format Version: 02 Page No. : 82 of 113

86 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 83 of 113

87 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH 1 / Ant. A Horizontal Report Format Version: 02 Page No. : 84 of 113

88 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 85 of 113

89 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH 13 / Ant. A Horizontal Report Format Version: 02 Page No. : 86 of 113

90 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 87 of 113

91 <For Antenna B> Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n 40MHz CH 3 / Ant. B Horizontal Report Format Version: 02 Page No. : 88 of 113

92 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 89 of 113

93 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n 40MHz CH 11 / Ant. B Horizontal Report Format Version: 02 Page No. : 90 of 113

94 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 91 of 113

95 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH 1 / Ant. B Horizontal Report Format Version: 02 Page No. : 92 of 113

96 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 93 of 113

97 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g CH 13 / Ant. B Horizontal Report Format Version: 02 Page No. : 94 of 113

98 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 95 of 113

99 Results of Receiver Spurious Emissions Above 1GHz <For Antenna A> Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 40MHz Ch 3 / Ant. A Horizontal Report Format Version: 02 Page No. : 96 of 113

100 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 97 of 113

101 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 40MHz Ch 11 / Ant. A Horizontal Report Format Version: 02 Page No. : 98 of 113

102 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 99 of 113

103 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g Ch 1 / Ant. A Horizontal Report Format Version: 02 Page No. : 100 of 113

104 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 101 of 113

105 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g Ch 13 / Ant. A Horizontal Report Format Version: 02 Page No. : 102 of 113

106 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 103 of 113

107 <For Antenna B> Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 40MHz Ch 3 / Ant. B Horizontal Report Format Version: 02 Page No. : 104 of 113

108 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 105 of 113

109 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations Draft n MCS0 40MHz Ch 11 / Ant. B Horizontal Report Format Version: 02 Page No. : 106 of 113

110 Vertical Note: The amplitude of spurious emissions which are lower by more than 6 db below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 107 of 113

111 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g Ch 1 / Ant. B Horizontal Report Format Version: 02 Page No. : 108 of 113

112 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 109 of 113

113 Temperature 23 Humidity 56% Test Engineer Sam Chen Configurations g Ch 13 / Ant. B Horizontal Report Format Version: 02 Page No. : 110 of 113

114 Vertical Note: The amplitude of spurious emissions that is lower by more than 6dB below the permissible value need not to be reported. Except fundamental harmonic emissions, other emissions listed have been verified as narrow band spurious emissions. Report Format Version: 02 Page No. : 111 of 113

115 5. LIST OF MEASURING EQUIPMENTS Instrument Manufacturer Model No. Serial No. Characteristics Spectrum Analyzer Calibration Date R&S FSEK khz - 40GHz Nov. 25, 2009 Amplifier Agilent 8447D 2944A kHz ~ 1.3GHz Jul. 03, 2009 Amplifier Agilent 8449B 3008A GHz ~ 26.5GHz Mar. 09, 2009 Bilog Antenna SCHAFFNER CBL6111C MHz ~ 2GHz Jul. 11, 2009 Horn Antenna COM-POWER AH GHz ~ 18GHz Jan. 16, 2009 Signal Generator R&S SMR MHz ~ 40GHz Mar. 09, 2009 RF Cable-R03m Jye Bao RG142 CB031 30MHz ~1GHz Aug. 19, 2009 RF Cable-HIGH SUHNER SUCOFLEX CH01-HY 1GHz~26.5GHz Jan. 16, 2009 Horn Antenna SCHWARZBECK BBHA9170 BBHA GHz ~ 40GHz Jan. 16, 2009 Turn Table HD DS /655/12 0 ~ 360 degree N/A Antenna Mast HD MA /569/12 1 m ~ 4 m N/A Spectrum Analyzer R&S FSU Hz ~ 26.5GHz Oct. 29, 2009 Power Meter R&S NRVS DC ~ 40GHz Jul. 31, 2009 Power Sensor R&S NRV-Z DC ~ 30GHz Aug. 05, 2009 Power Sensor R&S NRV-Z MHz ~ 6GHz Jul. 31, 2009 AC Power Source HPC HPA-500W HPA AC 0 ~ 300V Jul. 12, 2009* DC Power Source G.W. GPC-6030D C DC 1V ~ 60V Mar. 13, 2009 Temp. and Humidity Chamber Giant Force GTH S MAB N/A Aug. 06, 2009 RF CABLE-1m Jye Bao RG142 CB034-1m 20MHz ~ 7GHz Dec. 01, 2009 RF CABLE-2m Jye Bao RG142 CB035-2m 20MHz ~ 1GHz Dec. 01, 2009 Vector Signal Generator R&S SMU200A kHz ~ 6GHz Feb. 13, 2009 Signal Generator R&S SMR MHz ~ 40GHz Mar. 25, 2009 Note: Calibration Interval of instruments listed above is one year. Remark Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Radiation (05CH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) Conducted (TH01-HY) * Calibration Interval of instruments listed above is two year. NCR means Non-Calibration required. Report Format Version: 02 Page No. : 112 of 113

116 6. TEST LOCATION SHIJR ADD : 6Fl., No. 106, Sec. 1, Shintai 5th Rd., Shijr City, Taipei, Taiwan 221, R.O.C. TEL : FAX : HWA YA ADD : No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. TEL : FAX : LINKOU ADD : No. 30-2, Dingfu Tsuen, Linkou Shiang, Taipei, Taiwan 244, R.O.C TEL : FAX : DUNGHU ADD : No. 3, Lane 238, Kangle St., Neihu Chiu, Taipei, Taiwan 114, R.O.C. TEL : FAX : JUNGHE ADD : 7Fl., No. 758, Jungjeng Rd., Junghe City, Taipei, Taiwan 235, R.O.C. TEL : FAX : NEIHU ADD : 4Fl., No. 339, Hsin Hu 2 nd Rd., Taipei 114, Taiwan, R.O.C. TEL : FAX : JHUBEI ADD : No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. TEL : FAX : Report Format Version: 02 Page No. : 113 of 113

117 APPENDIX A. Photographs of EUT SPORTON International Inc. PAGE NUMBER : A1 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

118 SPORTON International Inc. PAGE NUMBER : A2 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

119 EUT 1. Two antenna connectors with two crystals SPORTON International Inc. PAGE NUMBER : A3 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

120 SPORTON International Inc. PAGE NUMBER : A4 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

121 SPORTON International Inc. PAGE NUMBER : A5 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

122 SPORTON International Inc. PAGE NUMBER : A6 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

123 EUT 2. Two antenna connectors with one crystal SPORTON International Inc. PAGE NUMBER : A7 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

124 SPORTON International Inc. PAGE NUMBER : A8 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

125 SPORTON International Inc. PAGE NUMBER : A9 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

126 EUT 3. One antenna connector with two crystals SPORTON International Inc. PAGE NUMBER : A10 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

127 SPORTON International Inc. PAGE NUMBER : A11 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

128 SPORTON International Inc. PAGE NUMBER : A12 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

129 EUT 4. One antenna connector with one crystal SPORTON International Inc. PAGE NUMBER : A13 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

130 SPORTON International Inc. PAGE NUMBER : A14 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

131 SPORTON International Inc. PAGE NUMBER : A15 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

132 Antenna A SPORTON International Inc. PAGE NUMBER : A16 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

133 SPORTON International Inc. PAGE NUMBER : A17 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

134 Antenna B SPORTON International Inc. PAGE NUMBER : A18 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

135 SPORTON International Inc. PAGE NUMBER : A19 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

136 SPORTON International Inc. PAGE NUMBER : A20 OF A20 TEL : ISSUED DATE : Jan. 18, 2010 FAX :

137 Appendix B. Test Photos Page No. : B1 of B5

138 1. Photographs of Test Configuration Test Mode: Mode 1 FRONT VIEW REAR VIEW Page No. : B2 of B5

139 SIDE VIEW Page No. : B3 of B5

140 Test Mode: Mode 2 FRONT VIEW REAR VIEW Page No. : B4 of B5

141 SIDE VIEW Page No. : B5 of B5