Report No.: 063L107-RF-CE-P14V02-2. Test Report. MICRO-STAR INTL Co., LTD. No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C.

Transcription

1 Test Report Product Name Model No. Wireless LAN Card MS-6877 Applicant Address MICRO-STAR INTL Co., LTD. No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. Date of Receipt June 14, 2006 Issued Date July 03, 2006 Report No. 063L107-RF-CE-P14V02-2 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Page: 1 of 24

2 Test Report Certification Issued Date : July 03, 2006 Report No.: 063L107-RF-CE-P14V02-2 Accredited by DNV, Nemko and NIST (NVLAP) Product Name Applicant Address Manufacturer Model No. Rated Voltage Wireless LAN Card MICRO-STAR INTL Co., LTD. No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. MICRO-STAR INTL Co., LTD. MS-6877 AC 230V/50Hz Working Voltage DC 3.3V Trade Name MSI Applicable Standard ETSI EN :V1.6.1 ( ) AS/NZS 4771: 2000+A1: 2003 Test Result Complied The test results relate only to the samples tested. The test report is under the previsions of Directive 1999/5/EC, Article 3.2. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Documented By : Tested By : ( Rita Huang ) 0914 Approved By : ( Tim Sung ) ( Gene Chang ) Page: 2 of 24

3 TABLE OF CONTENTS Report No.: 063L107-RF-CE-P14V02-2 Description Page 1. GENERAL INFORMATION EUT Description Test System Details Configuration of Test System EUT Exercise Software Test Facility Spurious Emission Test Equipment Test Setup Test Condition Limits Test Procedure Uncertainty Test Specification Test Result Measurement Uncertainty Values EMC Reduction Method During Compliance Testing Test Result Test Data of Spurious Emission Attachment 1: EUT Test Photographs Attachment 2: EUT Detailed Photographs Page: 3 of 24

4 1. GENERAL INFORMATION 1.1. EUT Description Product Name Trade Name Model No. Frequency Range Wireless LAN Card MSI MS MHz Channel Number 13 Data Speed DSSS: 1, 2, 5.5, 11Mbps OFDM: 6, 9, 12, 18, 24, 36, 48, 54Mbps Channel separation Type of Modulation Channel Control Antenna Type Antenna Gain 5 MHz DSSS / OFDM Auto Connector Refer to the table Antenna List Antenna List No. Manufacturer Part No. Peak Gain 1 FVC X20 (L) / X20 (R) 0.53dBi for 2.4GHz 2 FVC X40 (L) / X40 (R) 2.58dBi for 2.4GHz 3 FVC X72IA6 (L) / X72IA6 (R) 0.78dBi for 2.4GHz 4 FVC L51 (L) / L51 (R) 0.84dBi for 2.4GHz 5 FVC L41 (L) / L41 (R) 0.01dBi for 2.4GHz Page: 4 of 24

5 Working Frequency of Each Channel: Channel Frequency Channel Frequency Channel Frequency Channel Frequency Channel 01: 2412 MHz Channel 02: 2417 MHz Channel 03: 2422 MHz Channel 04: 2427 MHz Channel 05: 2432 MHz Channel 06: 2437 MHz Channel 07: 2442 MHz Channel 08: 2447 MHz Channel 09: 2452 MHz Channel 10: 2457 MHz Channel 11: 2462 MHz Channel 12: 2467 MHz Channel 13: 2472 MHz Note: 1. Regarding to the operation frequency, the lowest, middle and highest frequency at the highest data rate are selected to perform the test. 2. QuieTek verified all construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: EMI Mode Mode 1: Transmitter 11Mbps (Antenna 2) Mode 1: Transmitter 54Mbps (Antenna 2) Mode 2: Receiver 11Mbps (Antenna 2) Mode 2: Receiver 54Mbps (Antenna 2) Page: 5 of 24

6 1.2. Test System Details The types for all equipment, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. FCC ID Power Cord (1) Notebook PC DELL PPT N/A DoC Non-Shielded, 0.8m (2) MATRIX MSI N/A N/A N/A N/A Signal Cable Type A. N/A N/A Signal cable Description Page: 6 of 24

7 1.3. Configuration of Test System EUT MATRIX (2) Notebook PC (1) 1.4. EUT Exercise Software (1) Setup the EUT as shown in section 1.4 (2) Execute the CRTU program (the continuous transmission program) on the EUT (3) Setup the test mode, the test channel, and the data rate. (4) Press OK to start the transmission. (5) Verify that the EUT works correctly. Page: 7 of 24

8 1.5. Test Facility Ambient conditions in the laboratory: Items Test Item Required Actual Temperature ( C) ETSI EN Humidity (%RH) Site Description: Accreditation on NVLAP NVLAP Lab Code: June 11, 2001 Accreditation on DNV Statement No. : LAB11 April 18, 2001 Accreditation on Nemko Certificate No.: ELA 165 May 03, 2001 Accreditation on TUV Rheinland Certificate No.: Site Name: Site Address: Quietek Corporation No. 5, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL : / FAX : service@quietek.com Page: 8 of 24

9 2. Spurious Emission 2.1. Test Equipment The following test equipment are used during the radiated emission test: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 1 Test Receiver R & S ESVS 10 / /003 July, 2006 Spectrum Analyzer Advantest R3162/ May, 2006 Pre-Amplifier Advantest BB525C/ 3307A01812 May, 2006 Bilog Antenna SCHAFFNER CBL6112B / 2697 Nov., 2005 Site # 2 Test Receiver R & S ESCS 30 / / 022 Nov., 2005 Spectrum Analyzer Advantest R3162 / May, 2006 Pre-Amplifier Advantest BB525C/3307A01814 May, 2006 Bilog Antenna SCHAFFNER CBL6112B / 2705 Oct., 2005 Horn Antenna ETS 3115 / July, 2006 Pre-Amplifier QTK QTK-AMP-01/ 0001 July, 2006 Site # 3 Test Receiver R & S ESI 26 / / 004 May, 2006 Spectrum Analyzer Advantest R3162 / May, 2006 Pre-Amplifier QTK QTK-AMP-03 / 0003 May, 2006 Bilog Antenna SCHAFFNER CBL6112B / 2697 May, 2006 Horn Antenna ETS 3115 / July, 2006 Pre-Amplifier QTK QTK-AMP-01 / 0001 July, 2006 Note: 1. All equipments that need to calibrate are with calibration perio d of 1 year. 2. Mark X test instruments are used to measure the final test results Test Setup 3m FRP Dome 1m to 4m Non-Conducted Table Load EUT Antenna Mast Bilog or Horn Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 3m 1.5 m Test Receiver Fully Soldered Ground Plane TO Controller To Receiver Page: 9 of 24

10 2.3. Test Condition Standard Temperature and Humidity, Standard Test Voltage 2.4. Limits Transmitter limits for narrowband spurious emission Frequency Range Limit when operating Limit when in standby 30MHzto 1 GHz -36 dbm -57 dbm Above 1 GHz to GHz -30 dbm -47 dbm 1.8 GHz to 1.9 GHz 5.15 GHz to 5.3 GHz -47 dbm -47 dbm Transmitter limits for wideband spurious emission Frequency Range Limit when operating Limit when in standby 30MHzto 1 GHz -86 dbm/hz -107 dbm/hz Above 1 GHz to GHz -80 dbm/hz -97 dbm/hz 1.8 GHz to 1.9 GHz 5.15 GHz to 5.3 GHz -97 dbm/hz -97 dbm/hz Narrowband spurious emission limit for receivers Frequency Range 30MHzto 1 GHz Above 1 GHz to GHz Limit -57 dbm -47 dbm Wideband spurious emission limit for receivers Frequency Range 30MHzto 1 GHz Above 1 GHz to GHz Limit -107 dbm/hz -97 dbm/hz Page: 10 of 24

11 Report No.: 2.5. Test Procedure The EUT and its simulators are placed on a turn table which is 1.5 meters above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters.the antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Broadband antenna (calibrated bi-log and horn antenna) are used as a receiving antenna. Both horizontal and vertical polarization of the antenna are set on measurement. And a high frequency preamlifier were used increase the sensitivity of the measuring. In order to find the maximum emission, all of the interface cables must be manipulated according to ETSI EN :V1.5.1 ( ) on radiated measurement. The additional notch filter below 1GHz was used to measure the level of harmonics radiated emission during field dtrength of harmonics measurement. The bandwidth setting on the field strength meter (R & S Spectrum Analyzer FSP40 )is 100 khz. The frequency range from 30MHz to 12.75GHz is checked Uncertainty The measurement uncertainty above 1G is defined as ± 3.9 db under 1G is defined as ± 3.8 db 2.7. Test Specification According to ETSI EN :V1.6.1 ( ) 2.8. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 5. The acceptance criterion was met and the EUT passed the test. Page: 11 of 24

12 Report No.: 3. Measurement Uncertainty Values The maximum values of the absolute measurement uncertainties of the measurements defined in the present document shall not exceed the values given below: Parameter Uncertainty Radio frequency ± 1 x10 5 Total RF power, conducted ± 1.5 db RF power density, conducted ± 3 db Spurious emissions, conducted ± 3 db All emissions, radiated ± 6 db Temperature ± 1 o C Humidity ± 5 % DC and low frequency voltages ± 3 % Page: 12 of 24

13 Report No.: 4. EMC Reduction Method During Compliance Testing No modification was made during testing. Page: 13 of 24

14 Report No.: 5. Test Result The test results in the emission and the immunity were performed according to the requirements of measurement standard and process. Quietek Corporation is assumed full responsibility for the accuracy and completeness of these measurements. The test data of the emission is listed as below. All the tests were carried out with the EUT in normal operation, which was defined as: EMI Mode Mode 1: Transmitter 11Mbps (Antenna 2) Mode 1: Transmitter 54Mbps (Antenna 2) Mode 2: Receiver 11Mbps (Antenna 2) Mode 2: Receiver 54Mbps (Antenna 2) Page: 14 of 24

15 Report No.: 5.1. Test Data of Spurious Emission Product : Wireless LAN Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 1: Transmitter 11Mbps (Antenna 2)(Channel 1) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (db) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2. means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 15 of 24

16 Product : Wireless LAN Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 1: Transmitter 11Mbps (Antenna 2)(Channel 13) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (db) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2. means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 16 of 24

17 Product : Wireless LAN Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 1: Transmitter 54Mbps (Antenna 2)(Channel 1) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (db) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2. means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 17 of 24

18 Product : Wireless LAN Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 1: Transmitter 54Mbps (Antenna 2)(Channel 13) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (db) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2. means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 18 of 24

19 Product : Wireless LAN Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 2: Receiver 11Mbps (Antenna 2)(Channel 1) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (db) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2. means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 19 of 24

20 Report No.: Product : Wireless LAN Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 2: Receiver 11Mbps (Antenna 2) (Channel 13) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (db) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2. means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 20 of 24

21 Report No.: Product : Wireless LAN Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 2: Receiver 54Mbps (Antenna 2) (Channel 1) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (db) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2. means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 21 of 24

22 Report No. 063L107-RF-CE-P14V02-2 Product : Wireless LAN Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 2: Receiver 54Mbps (Antenna 2) (Channel 13) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (db) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2. means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page:22 of 24

23 Report No. 063L107-RF-CE-P14V02-2 Attachment 1: EUT Test Photographs Page:23 of 24

24 Attachment 1: EUT Test Setup Photographs Front View of Spurious Emission Test Back View of Spurious Emission Test Page : 1 of 2

25 Front View of Spurious Emission Test (Horn) Back View of Spurious Emission Test (Horn) Page : 2 of 2

26 Report No. 063L107-RF-CE-P14V02-2 Attachment 2: EUT Detailed Photographs Page:24 of 24

27 Attachment 2 : EUT Detailed Photographs (1) Antenna Photo (2) Antenna Photo Page : 1 of 5

28 (3) Antenna Photo (4) EUT Photo Page : 2 of 5

29 (5) Antenna Photo (6) EUT Photo Page : 3 of 5

30 (7) EUT Photo (8) Antenna Photo Page : 4 of 5

31 (9) EUT Photo (10) EUT Photo Page : 5 of 5