FCC 47 CFR PART 15 SUBPART C ANSI C63.4: 2009

Transcription

1 FCC 47 CFR PART 15 SUBPART C ANSI C63.4: 2009 TEST REPORT For Z-WAVE DOOR SENSOR Model: ZD2102 Trade Name: N/A Issued to Vision Automobile Electronics Industrial Co., Ltd. No. 17, Alley 92, Lane 189, Sec. 1, An Chung Road, Tainan, Taiwan Issued by Compliance Certification Services Inc. Tainan Lab. No. 8, Jiu Ceng Ling, Jiaokeng Village, Sinhua Township, Tainan Hsien 712, Taiwan (R.O.C.) TEL: (06) FAX: (06) Issued Date: April 10, 2011 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 32 Rev. 00

2 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION EUT DESCRIPTION TEST METHODOLOGY EUT CONFIGURATION EUT EXERCISE GENERAL TEST PROCEDURES FCC PART RESTRICTED BANDS OF OPERATIONS DESCRIPTION OF TEST MODES INSTRUMENT CALIBRATION MEASURING INSTRUMENT CALIBRATION MEASUREMENT EQUIPMENT USED MEASUREMENT UNCERTAINTY FACILITIES AND ACCREDITATIONS FACILITIES EQUIPMENT TABLE OF ACCREDITATIONS AND LISTINGS TABLE OF ACCREDITATIONS AND LISTINGS SETUP OF EQUIPMENT UNDER TEST SETUP CONFIGURATION OF EUT SUPPORT EQUIPMENT FCC PART REQUIREMENTS DB BANDWIDTH BAND EDGES MEASUREMENT SPURIOUS EMISSION POWERLINE CONDUCTED EMISSIONS APPENDIX I PHOTOGRAPHS OF TEST SETUP APPENDIX II PHOTOGRAPHS OF EUT... A1 Page 2 Rev. 00

3 1. TEST RESULT CERTIFICATION Product: Z-WAVE DOOR SENSOR Model: ZD2102 Brand Name: N/A Applicant: Vision Automobile Electronics Industrial Co., Ltd. No. 17, Alley 92, Lane 189, Sec. 1, An Chung Road, Tainan, Taiwan Manufacturer: Vision Automobile Electronics Industrial Co., Ltd. No. 17, Alley 92, Lane 189, Sec. 1, An Chung Road, Tainan, Taiwan Tested: March 16, 2011 ~ April 10, 2011 STANDARD APPLICABLE STANDARDS TEST RESULT FCC 47 CFR Part 15 Subpart C ANSI C63.4 : 2009 No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2003 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements emission limits of FCC Rules Part , ,15.207, and The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Jeter Wu Assistant Manager Eric Huang Assistant Section Manager Page 3 Rev. 00

4 2. EUT DESCRIPTION Product Model Number Brand Name Frequency Range Operating Frequency Data Rate Number of Channels Type of Modulation Power Supply Antenna Type Temperature Range Z-WAVE DOOR SENSOR ZD2102 VISION 902MHz ~ 928MHz MHz ± 20kHz 9.6 kbps, 40kbps 1 Channel FSK Powered from Lithium battery, 5Vdc Wire antenna Gain: -10 dbm -15 C ~ +60 C Remark: 1. Client consigns only one model sample to test (Model Number: ZD2102). Therefore, the testing Lab. just guarantees the unit, which has been tested. 2. This submittal(s) (test report) is intended for FCC ID: KFR-ZD2102US filing to comply with Section & (FCC Part 15, Subpart B) and Section , , Page 4 Rev. 00

5 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 and FCC CFR , , , , , , , , and EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section and under the FCC Rules Part 15 Subpart B and Section , , under the FCC Rules Part 15 Subpart C. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section of ANSI C63.4 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section of ANSI C63.4. Page 5 Rev. 00

6 3.4 FCC PART RESTRICTED BANDS OF OPERATIONS (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz Until February 1, 1999, this restricted band shall be MHz. 2 Above ( 2 ) (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section At frequencies equal to or less than 1000 MHz, compliance with the limits in Section shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section shall be demonstrated based on the average value of the measured emissions. The provisions in Section apply to these measurements. 3.5 DESCRIPTION OF TEST MODES The EUT( Model: ZD2102 ) had been tested under engineering test mode condition and the EUT staying in continuous transmitting mode. Note: 1)The field strength of spurious emission was measured in the following position: EUT have three test modes(x, Y, Z axis). The worst emission was found in Z axis and the worst case was recorded. 2)EUT has supported two data rates (9.6kbps, 40kbps ) which have been investigated during the test, and found the 9.6Kbps as the worst case recorded. Page 6 Rev. 00

7 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Open Area Test Site # 6 Name of Equipment Manufacturer Model Serial Number Calibration Due TYPE N COAXIAL CABLE SUHNER CHA NOV. 17, 2011 BI-LOG Antenna Sunol JB1 A OCT. 4, 2011 LOOP ANTENNA EMCO JUN. 10, 2011 Pre-Amplifier HP 8447F 2944A03817 NOV. 23, 2011 EMI Receiver R&S ESVS /012 MAY 10, 2011 RF Cable SUHNER SUCOFLEX104PEA 20520/4PEA NOV. 10, 2011 Horn Antenna Com-Power AH DEC. 27, 2011 Spectrum Analyzer R&S FSEK /002 JUL. 14, 2011 Pre-Amplifier MITEQ AFS P NOV. 23, 2011 Turn Table Yo Chen N.C.R. Antenna Tower AR TP1000A N.C.R. Controller CT SC N.C.R. RF Swicth E-INSTRUME NT TELH LTD ERS-180A EC N.C.R Test S/W e-3 ( e) Remark: Each piece of equipment is scheduled for calibration once a year. Page 7 Rev. 00

8 4.3 MEASUREMENT UNCERTAINTY Parameter Radiated Emission, 30 to 200 MHz Test Site : OATS-6 Radiated Emission, 200 to 1000 MHz Test Site : OATS-6 Radiated Emission, 1 to 26.5 GHz Power Line Conducted Emission Band Width Peak Output Power MU Band Edge MU Channel Separation MU Duty Cycle MU Frequency Stability MU Uncertainty ±3.38dB ±3.04dB ± 2.38 db ±2.01dB kHz ±1.904dB ±0.302dBuV Hz 0.064ms 0.223kHz Uncertainty figures are valid to a confidence level of 95%, k=2 Page 8 Rev. 00

9 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No. 8, Jiu Ceng Ling, Jiaokeng Village,Sinhua Township, Tainan Hsien 712, Taiwan (R.O.C.) The sites are constructed in conformance with the requirements of ANSI C63.7:1992, ANSI C63.4 : 2009 and CISPR Publication EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, Radio Interference Measuring Apparatus and Measurement Methods. 5.3 TABLE OF ACCREDITATIONS AND LISTINGS The test facilities used to perform radiated and conducted emissions tests are accredited by Taiwan Accreditation Foundation for the specific scope of accreditation under Lab Code: 1109 to perform Electromagnetic Interference tests according to FCC PART 15 AND CISPR 22 requirements. No part of this report may be used to claim or imply product endorsement by TAF or any agency of the Government. In addition, the test facilities are listed with Federal Communications Commission (registration no: TW-1037). Page 9

10 5.1 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo USA Taiwan FCC TAF 3/10 meter Open Area Test Sites to perform FCC Part 15/18 measurements CISPR 11, FCC METHOD-47 CFR Part 18, EN 55011, EN , CISPR 22, CNS 13438, EN 55022, EN 55024, AS/NZS CISPR 22 CISPR 14, EN , EN , CNS , CISPR 22, CNS 13439, EN 55013, FCC Method-47 CFR Part 15 Subpart B, IC ICES-003, VCCI V-3 & V-4 FCC Method-47 CFR Part 15 Subpart C and ANSI C63.4, LP 0002 EN / IEC / -3 / -4 / -5 / -6 / -8 / -11 EN , EN EN , EN , AS/NZS , EN , EN , AS/NZS , EN , EN , EN , EN 50371, EN 50385, AS/NZS 4268, ETSI EN ETSI EN , ETSI EN /-3/-9/-17 ETSI EN , ETSI EN /-1 ETSI EN /-1 ETSI EN /-1 RSS-310, RSS-210 Issue 7, RSS-Gen Issue 2 TW-1037 Taiwan BSMI CNS 13438, CNS , CNS13439 SL2-IN-E-0039 SL2-R1/R SL2-A1-E-0039 Canada Industry Canada RSS210, Issue 7 IC 2324H-1 * No part of this report may be used to claim or imply product endorsement by TAF or any agency of the US Government. Page 10 Rev. 00

11 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix I for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No. Product Manufacturer Model No. Certify No. Signal cable 1 N/A No. Signal cable description A N/A Remark: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer s requirements and conditions for the intended use. Page 11 Rev. 00

12 7. FCC PART REQUIREMENTS DB BANDWIDTH LIMIT None; for reporting purposes only. MEASUREMENT EQUIPMENT USED Name of Equipment Manufacturer Model Serial Number Calibration Due SPECTRUM ANALYZER R&S FSEK /002 JUL. 14, 2011 Remark: Each piece of equipment is scheduled for calibration once a year. Test Configuration EUT Spectrum Analyzer TEST PROCEDURE The transmitter output is connected to the spectrum analyzer. The spectrum analyzer center frequency is set to the transmitter frequency. The RBW is set to 10 khz and VBW is set 30kHz. TEST RESULTS No non-compliance noted. Test Data Frequency (MHz) 20dB Bandwidth (KHz) Page 12 Rev. 00

13 Test Plot Page 13 Rev. 00

14 7.2 BAND EDGES MEASUREMENT LIMIT 1. In the above emission table, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (μv/m at 3-meter) (dbμv/m at 3-meter) Above As shown in Section 15.35(b), for frequencies above 1000 MHz, the above field strength limits in paragraphs (a) and (b) of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 db under any condition of modulation. For point-to-point operation under paragraph (b) of this section, the peak field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth. Test Configuration Antenna tower EUT 3m 4m Horn antenna Spectrum analyzer Turntable 0.8m 1m Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission. 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 5. Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. TEST RESULTS Refer to attach spectrum analyzer data chart. Page 14 Rev. 00

15 Band Edges Detector mode : Peak (Channel Low) Polarity : Horizontal Detector mode : Peak (Channel Low) Polarity : Vertical Page 15 Rev. 00

16 Detector mode : Peak (Channel High) Polarity : Horizontal Detector mode : Peak (Channel High) Polarity : Vertical Page 16 Rev. 00

17 7.3 SPURIOUS EMISSION LIMIT 1. In the section (a): Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: Fundamental Frequency (MHz) Field Strength of Fundamental Field Strength (mv/m) Field Strength of Harmonics (μv/m) MHz MHz MHz GHz Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency (MHz) Field Strength (μv/m) Measurement Distance (m) * * * 3 Above Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands MHz, MHz, MHz or MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections and In the above emission table, the tighter limit applies at the band edges. Frequency (MHz) Field Strength (μv/m at 3-meter) Field Strength (dbμv/m at 3-meter) Above Page 17 Rev. 00

18 MEASUREMENT EQUIPMENT USED Open Area Test Site # 6 Name of Equipment Manufacturer Model Serial Number Calibration Due TYPE N COAXIAL CABLE SUHNER CHA NOV. 17, 2011 BI-LOG Antenna Sunol JB1 A OCT. 4, 2011 LOOP ANTENNA EMCO JUN. 10, 2011 Pre-Amplifier HP 8447F 2944A03817 NOV. 23, 2011 EMI Receiver R&S ESVS /012 MAY 10, 2011 RF Cable SUHNER SUCOFLEX104PEA 20520/4PEA NOV. 10, 2011 Horn Antenna Com-Power AH DEC. 27, 2011 Spectrum Analyzer R&S FSEK /002 JUL. 14, 2011 Pre-Amplifier MITEQ AFS P NOV. 23, 2011 Turn Table Yo Chen N.C.R. Antenna Tower AR TP1000A N.C.R. Controller CT SC N.C.R. RF Swicth E-INSTRUME NT TELH LTD ERS-180A EC N.C.R Test S/W e-3 ( e) Remark: Each piece of equipment is scheduled for calibration once a year. Page 18 Rev. 00

19 Test Configuration 9kHz ~ 30MHz EUT 3m Loop antenna Spectrum / Receiver Turntable 0.8m 1m Reference ground plane 30MHz ~ 1GHz Antenna tower EUT 3m 4m Bi-log antenna Spectrum analyzer Turntable 0.8m 1m Reference ground plane Page 19 Rev. 00

20 Above 1 GHz Antenna tower EUT 3m 4m Horn antenna Spectrum analyzer Turntable 0.8m 1m Pre-amp Page 20 Rev. 00

21 TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Below 1GHz: RBW=100kHz / VBW=300kHz / Sweep=AUTO Above 1GHz: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. Page 21 Rev. 00

22 Below 1 GHz Operation Mode: TX / Y Mode Test Date: March 24, 2011 Temperature: 21.8 C Tested by: John Chen Humidity: 63% RH Polarity: Ver. / Hor. Horizontal Remark: 1. No emission found between lowest internal used/generated frequency to 30MHz (9kHz~30MHz). 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak detector mode. 3. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit or as required by the applicant. 4. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie: margin>20db from the applicable limit) and considered that's already beyond the background noise floor. 5. Margin (db) = Remark result (dbuv/m) Quasi-peak limit (dbuv/m). Page 22 Rev. 00

23 Operation Mode: TX / Y Mode Test Date: March 24, 2011 Temperature: 21.8 C Tested by: John Chen Humidity: 63% RH Polarity: Ver. / Hor. Vertical Remark: 1. No emission found between lowest internal used/generated frequency to 30MHz (9kHz~30MHz). 2. Radiated emissions measured in frequency range from 30 MHz to 1000MHz were made with an instrument using peak/quasi-peak detector mode. 3. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit or as required by the applicant. 4. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie: margin>20db from the applicable limit) and considered that's already beyond the background noise floor. 5. Margin (db) = Remark result (dbuv/m) Quasi-peak limit (dbuv/m). Page 23 Rev. 00

24 Above 1 GHz EUT has supported two data rates (9.6kbps, 40kbps ) which have been investigated during the test, and found the 9.6Kbps as the worst case recorded. Operation Mode: TX / Y Mode Test Date: March 16, 2011 Temperature: 24.8 C Tested by: John Chen Humidity: 58% RH Polarity: Ver. / Hor. Horizontal Freq. Reading AF Cable Loss Pre-amp Filter Level Limit Margin Mark (MHz) (dbμv) (db/m) (db) (db) (db) (dbμv/m) (dbμv/m) (db) (P/Q/A) P A P A P A P A N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie: margin>20db from the applicable limit) and considered that's already beyond the background noise floor. 6. Margin (db) = Remark result (dbuv/m) Average limit (dbuv/m). Peak detector mode and average detector mode of the emission shown in Result column. Page 24 Rev. 00

25 Operation Mode: TX / Y Mode Test Date: March 16, 2011 Temperature: 24.8 C Tested by: John Chen Humidity: 58% RH Polarity: Ver. / Hor. Vertical Freq. Reading AF Cable Loss Pre-amp Filter Level Limit Margin Mark (MHz) (dbμv) (db/m) (db) (db) (db) (dbμv/m) (dbμv/m) (db) (P/Q/A) P A P A P A P A N/A Remark: 7. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 8. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 9. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 10. Data of measurement within this frequency range shown --- in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 11. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with N/A remark, if no specific emissions from the EUT are recorded (ie: margin>20db from the applicable limit) and considered that's already beyond the background noise floor. 12. Margin (db) = Remark result (dbuv/m) Average limit (dbuv/m). Peak detector mode and average detector mode of the emission shown in Result column. Page 25 Rev. 00

26 7.4 POWERLINE CONDUCTED EMISSIONS LIMIT According to (a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 khz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 µh/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Frequency Range (MHz) Quasi-peak Limits (dbμv) Average 0.15 to to to to to Compliance with this provision shall be based on the measurement of the radio frequency voltage between each power line (LINE and NEUTRAL) and ground at the power terminals. MEASUREMENT EQUIPMENT USED Conducted Emission room #1 Name of Equipment Manufacturer Model Serial Number Calibration Due L.I.S.N. SCHWARZBECK NNLK MAR. 09, 2011 TEST RECEIVER Rohde & Schwarz ESCS JUL. 13, 2011 BNC COAXIAL CCS BNC50 11 OCT. 04, 2011 CABLE e-3 ( c) Test S/W R&S (2.27) Remark: Each piece of equipment is scheduled for calibration once a year. Test results Since this EUT is battery powered, this test item is not applicable. Page 26 Rev. 00