Test Report. Product Name: Cable Modem Model No.: BEFCMU10 ver.3 FCC ID. : Q87-BEFCMU10V3

Transcription

1 Report No. 036H064FI Test Report Product Name: Cable Modem Model No.: BEFCMU10 ver.3 FCC ID. : Q87-BEFCMU10V3 Applicant : Cisco-Linksys, LLC Address : Armstrong Avenue, Irvine, CA USA Date of Receipt : Jun. 19, 2003 Date of Test : Jun. 24, 2003 Report No. : 036H064FI The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Page : 1 of 21

2 Report No. 036H064FI Test Report Certification Test Date : Jun. 24, 2003 Report No. : 036H064FI Accredited by NIST (NVLAP) NVLAP Lab Code: Product Name : Cable Modem Applicant : Cisco-Linksys, LLC Address : Armstrong Avenue, Irvine, CA USA Manufacturer : ASKEY COMPUTER CORP. Model No. : BEFCMU10 ver.3 FCC ID. : Q87-BEFCMU10V3 Rated Voltage : AC 120V/60Hz Trade Name : Linksys Measurement Standard : FCC Part 15 Subpart B: 2002, CISPR 22:1997. Measurement Procedure : ANSI C63.4: 1992 Classification : Class B Test Result : Complied The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Documented By : ( Lydia Tsai ) Tested By : (Allen Wu ) Approved By : ( Kevin Wang ) Page : 2 of 21

3 Report No. 036H064FI Description TABLE OF CONTENTS Page 1. GENERAL INFORMATION EUT Description Tested System Details Configuration of tested System EUT Exercise Software Test Facility Conducted Emission Test Equipment Test Setup Limits Test Procedure Test Result Radiated Emission Test Equipment Test Setup Limits Test Procedure Test Result EMI Reduction Method During Compliance Testing Summary of Test Datas Test Data of conducted Emission Test Data of Radiated Emission...18 Attachment 1: EUT Test Photographs Attachment 2: EUT Detailed Photographs Page : 3 of 21

4 Report No. 036H064FI 1. GENERAL INFORMATION 1.1. EUT Description Product Name : Cable Modem Trade Name : Linksys Model No. : BEFCMU10 ver.3 FCC ID. : Q87-BEFCMU10V3 USB Cable : Non-shielded, 1.5m LAN Cable : Non-shielded, 3.0m Power Adapter (Mode1) : OEM, AD-121ANDT Cable IN: Non-shielded, 1.9m Cable Out: Non-shielded, 1.9m Power Adapter (Mode2) : DELTA, ADP-12SB Rev. B Cable Out: Non-shielded, 1.8m Power Cord : Non-shielded, 1.8m Note: 1. This EUT is a Cable Modem. 2. QuieTek has verified both construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: EMI Mode: Mode 1: Cable Modem OEM AD-121ANDT Mode 2: Cable Modem DELTA ADP-12SB Rev. B Page : 4 of 21

5 Report No. 036H064FI 1.2. Tested System Details The types for all equipment, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord (1) PC HP DTPC27 SG Non-shielded, 1.8m (2) Monitor LEMEL VA-570 OS Non-shielded, 1.8m (3) Keyboard ACER 6311-TW4C/6 N/A -- (4) Mouse Logitech M-S35 LZA (5) USB Mouse Logitech M-UE55 N/A -- (6) Modem ACEEX DM Non-shielded, 1.6m (7) Printer HP C2642A MY75N1D2BC Non-shielded, 0.7m (8) Walkman TOBISHI TB-1027 TBS (9) Microphone & Earphone TOKTO SX-MI N/A -- (10) Joystick Logitech LCB (11) Notebook PC ACER B0160C91000CF2M Non-shielded, 1.8m (12) CMTS1000 Nortel Dess01E Non-shielded, 1.8m (13) Server Mitac 6835E N/A Non-shielded, 1.8m (14) LAN Card D-LINK DFE-500TX 0080C Signal Cable Type Signal cable Description A VGA Cable Shielded, 1.6m, a ferrite core bonded. B Keyboard Cable Shielded, 1.8m C Mouse Cable Shielded, 1.8m D USB Cable Shielded, 1.5m E USB Mouse Cable Shielded, 1.0m F Walkman Cable Non-Shielded, 1.6m G LAN Cable Non-Shielded, 10m H Coaxial Cable Shielded, 10m I Microphone & Earphone Cable Non-Shielded, 1.2m J Joystick Cable Shielded, 2.0m K Printer Cable Shielded, 1.2m L Modem Cable Shielded, 1.5m M LAN Cable Non-Shielded, 3.0m Page : 5 of 21

6 Report No. 036H064FI 1.3. Configuration of tested System A D L K Monitor(2) PC(1) EUT Printer(7) B C E USB Mouse(5) F I Modem(6) J G H Keyboard (3) Mouse(4) Walkman(8) Microphone & Earphone(9) Joystick(10) Notebook PC(11) CMTS1000(12) M LAN Card(14) Server(13) 1.4. EUT Exercise Software (1) Setup the EUT and simulators as shown on 1.4. (2) Turn on the power of all equipment. (3) Boot the PC from Hard Disk. (4) Data will communicate between personal computer and EUT. (5) The personal computer's monitor will show the transmitting and receiving characteristics when the communication is success. (6) Repeat the above procedure (4) to (5) Page : 6 of 21

7 Report No. 036H064FI 1.5. Test Facility Ambient conditions in the laboratory: Items Required (IEC 68-1) Actual Temperature ( C) Humidity (%RH) Barometric pressure (mbar) Site Description: Site Name: Site Address: November 3, 1998 File on Federal Communications Commission FCC Engineering Laboratory 7435 Oakland Mills Road Columbia, MD Reference 31040/SIT1300F2 August 30, 2001 Accreditation on NVLAP NVLAP Lab Code: Quietek Corporation No.75-1, Wang-Yeh Valley, Yung-Hsing, Chiung-Lin, Hsin-Chu County, Taiwan, R.O.C. TEL: / FAX: service@quietek.com Page : 7 of 21

8 Report No. 036H064FI 2. Conducted Emission 2.1. Test Equipment The following test equipment are used during the test: Item Equipment Manufacturer Model No. / Serial No. Last Cal. Remark 1 Test Receiver R & S ESCS 30 / /018 Aug., Artificial Mains Network R & S ENV4200 / /10 Feb., 2003 Peripherals 3 LISN R & S ESH3-Z5 / /002 Feb., 2003 EUT 4 Pulse Limiter R & S ESH3-Z2 / Feb., No.2 Shielded Room N/A Note: All equipment upon which need to calibrated are with calibration period of 1 year Test Setup Reference Plane Test Receiver 40cm 12dBuV Load EUT LISN LISN Ground Plane LISN Page : 8 of 21

9 Report No. 036H064FI 2.3. Limits Frequency FCC Part 15 Subpart B Limits (dbuv) Class A Class B MHz QP AV QP AV Remarks : In the above table, the tighter limit applies at the band edges Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refers to the block diagram of the test setup and photographs.) Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and the entire interface cables must be changed according to ANSI C63.4: 1992 on conducted measurement. Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 5. The acceptance criterion was met and the EUT passed the test. Page : 9 of 21

10 Report No. 036H064FI 3. Radiated Emission 3.1. Test Equipment The following test equipment are used during the test: Test Site Equipment Manufacturer Model No. / Serial No. Last Cal. OATS # 1 X Test Receiver R & S ESCS 30 / /017 Jan., 2003 OATS # 2 OATS # 3 Note: X Spectrum Analyzer Advantest R3261C / N/A X Pre-Amplifier HP 8447D / 2944A09276 N/A X Bilog Antenna Chase CBL6112B / 2455 Sep., 2002 Test Receiver R & S ESCS 30 / /023 Jan., 2003 Spectrum Analyzer Advantest R3261C / N/A Pre-Amplifier QuieTek QTK-AMP / AMP1 N/A Bilog Antenna Chase CBL6112B / 2708 Sep., 2002 Test Receiver R & S ESCS 30 / /014 Jun., 2003 Spectrum Analyzer Advantest R3162 / N/A Pre-Amplifier Advantest BB525C / N/A N/A Bilog Antenna Schaffner CBL6112B / 2673 Sep., All equipments that need to calibrate are with calibration period of 1 year. 2. Mark X test instruments are used to measure the final test results Test Setup 3m FRP Dome 1m to 4m Non-Conducted Table EUT Antenna Mast Broadband or Dipole Antenna Antenna height can be moved from 1m to 4m. 80cm Test Receiver Fully Metal Mesh Ground Plane To Controller To Receiver Page : 10 of 21

11 Report No. 036H064FI 3.3. Limits CISPR 22 Limits (dbuv) Frequency Class A Class B MHz Distance (m) dbuv/m Distance (m) dbuv/m Remark: 1. The tighter limit shall apply at the edge between two frequency bands. 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. 3. RF Line Voltage (dbuv/m) = 20 log RF Line Voltage (uv/m) 3.4. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 10 meters. The antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to ANSI C63.4:1992 on radiated measurement. Radiated emissions were invested over the frequency range from 30MHz to1ghz using a receiver bandwidth of 120kHz. Radiated was performed at an antenna to EUT distance of 10 meters Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 5. The acceptance criterion was met and the EUT passed the test Page : 11 of 21

12 Report No. 036H064FI 4. EMI Reduction Method During Compliance Testing No modification was made during testing. Page : 12 of 21

13 Report No. 036H064FI 5. Summary of Test Datas The test results in the emission was performed according to the requirements of measurement standard and process. Quietek Corporation is assumed full responsibility for the accuracy and completeness of these measurements. The test data of the emission is listed as below. All the tests were carried out with the EUT in normal operation, which was defined as: EMI Mode: Mode 1: Cable Modem OEM AD-121ANDT Mode 2: Cable Modem DELTA ADP-12SB Rev. B Page : 13 of 21

14

15

16 Report No. 036H064FI 5.1. Test Data of conducted Emission Product : Cable Modem Test Item : Conducted Emission Test Power Line : Line 1 Test Mode : Mode 1: Cable Modem OEM AD-121ANDT Frequency Cable LISN Reading Emission Limits Loss Factor Level Level MHz db db dbuv dbuv dbuv ======================================================================== Quasi-Peak * Average: Note: 1. All Reading Levels are Quasi-Peak and average value. 2. *, means this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable loss. Page : 14 of 21

17

18

19

20

21 Report No. 036H064FI Product : Cable Modem Test Item : Conducted Emission Test Power Line : Line 2 Test Mode : Mode 1: Cable Modem OEM AD-121ANDT Frequency Cable LISN Reading Emission Limits Loss Factor Level Level MHz db db dbuv dbuv dbuv ======================================================================== Quasi-Peak * Average: Note: 1. All Reading Levels are Quasi-Peak and average value. 2. *, means this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable loss. Page : 15 of 21

22

23

24

25

26

27

28 Report No. 036H064FI Product : Cable Modem Test Item : Conducted Emission Test Power Line : Line 1 Test Mode : Mode 2: Cable Modem DELTA ADP-12SB Rev. B Frequency Cable LISN Reading Emission Limits Loss Factor Level Level MHz db db dbuv dbuv dbuv ======================================================================== Quasi-Peak * Average: Note: 1. All Reading Levels are Quasi-Peak and average value. 2. *, means this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable loss. Page : 16 of 21

29

30

31

32

33

34

35

36

37 Report No. 036H064FI Product : Cable Modem Test Item : Conducted Emission Test Power Line : Line 2 Test Mode : Mode 2: Cable Modem DELTA ADP-12SB Rev. B Frequency Cable LISN Reading Emission Limits Loss Factor Level Level MHz db db dbuv dbuv dbuv ======================================================================== Quasi-Peak * Average: Note: 1. All Reading Levels are Quasi-Peak and average value. 2. *, means this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable loss. Page : 17 of 21

38

39

40 Report No. 036H064FI 5.2 Test Data of Radiated Emission Product : Cable Modem Test Item : Radiated Emission Test Site : No.1 OATS Test Mode : Mode 1: Cable Modem OEM AD-121ANDT Freq. Cable Probe PreAMP Reading Emission Margin Limit Loss Factor Level Level MHz db db/m db dbuv dbuv/m db dbuv/m ========================================================== Horizontal * Vertical * Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Emission Level = Reading Level + Probe Factor + Cable loss. Page : 18 of 21

41

42

43 Report No. 036H064FI Product : Cable Modem Test Item : Radiated Emission Test Site : No.1 OATS Test Mode : Mode 2: Cable Modem DELTA ADP-12SB Rev. B Freq. Cable Probe PreAMP Reading Emission Margin Limit Loss Factor Level Level MHz db db/m db dbuv dbuv/m db dbuv/m ========================================================== Horizontal * Vertical * Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Emission Level = Reading Level + LISN Factor + Cable loss. Page : 19 of 21

44 Report No. 036H064FI Attachment 1: EUT Test Photographs Page : 20 of 21

45 Report No.: 036H064F Attachment 1 : EUT Test Photographs Front View of Conducted Test (Mode 1) Back View of Conducted Test (Mode 1) Page : 1 of 4

46 Report No.: 036H064F Front View of Conducted Test (Mode 2) Back View of Conducted Test (Mode2) Page : 2 of 4

47 Report No.: 036H064F Front View of Radiated Test (Mode 1) Back View of Radiated Test (Mode 1) Page : 3 of 4

48 Report No.: 036H064F Front View of Radiated Test (Mode 2) Back View of Radiated Test (Mode 2) Page : 4 of 4

49 Report No. 036H064FI Attachment 2: EUT Detailed Photographs Page : 21 of 21