CERTIFICATE. Issued Date: Aug. 20, 2009 Report No.: R-ITUSP02V01

Transcription

1 CERTIFICATE Issued Date: Aug. 20, 2009 Report No.: R-ITUSP02V01 This is to certify that the following designated product Product : TCF-142-RM Series/Rack Chassis Trade name : Moxa Model Number : TCF-142-S-SC-RM, TCF-142-S-ST-RM, TCF-142-M-SC-RM, TCF-142-M-ST-RM, TRC-190-DC-48 Company Name : Moxa Inc. This product, which has been issued the test report listed as above in QuieTek Laboratory, is based on a single evaluation of one sample and confirmed to comply with the requirements of the following EMC standard. FCC CFR Title 47 Part 15 Subpart B: 2008 Class A, CISPR 22: 2005 ANSI C63.4: 2003 ICES-003 Issue 4: 2004 Class A TEST LABORATORY Vincent Lin / Manager No.5-22, Ruei-Shu Valley, Ruei-Ping Tsuen Lin Kou Shiang, Taipei 244 Taiwan, R.O.C. TEL: FAX: service@quietek.com

2 Appendix Report Compliance with Industry Canada Interference-Causing Equipment Standard ICES-003 Product Name : TCF-142-RM Series/Rack Chassis Model No. : TCF-142-S-SC-RM, TCF-142-S-ST-RM, TCF-142-M-SC-RM, TCF-142-M-ST-RM, TRC-190-DC-48 Applicant : Moxa Inc. Address : Fl.4, No. 135, Lane 235, Pao-Chiao Rd., Shing Tien City, Taipei, Taiwan, R.O.C. Date of Receipt : 2009/05/25 Issued Date : 2009/08/20 Report No. : R-ITUSP02V01 Report Version : V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF, NVLAP, NIST or any agency of the Government. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation.

3 Test Report Certification Issued Date : 2009/08/20 Report No. : R-ITUSP02V01 Product Name : TCF-142-RM Series/Rack Chassis Applicant : Moxa Inc. Address : Fl.4, No. 135, Lane 235, Pao-Chiao Rd., Shing Tien City, Taipei, Taiwan, R.O.C. Manufacturer : Moxa Inc. Model No. : TCF-142-S-SC-RM, TCF-142-S-ST-RM, TCF-142-M-SC-RM, TCF-142-M-ST-RM, TRC-190-DC-48 EUT Rated Voltage : DC 48V EUT Test Voltage : DC 48V Trade Name : Moxa Applicable Standard : FCC CFR Title 47 Part 15 Subpart B: 2008 Class A CISPR 22: 2005 ANSI C63.4: 2003 ICES-003 Issue 4: 2004 Class A Test Result : Complied Performed Location : Quietek Corporation (Linkou Laboratory) No.5-22,Ruei-Shu Valley, Ruei-Ping Tsuen Lin Kuo Shiang, Taipei, 244 Taiwan, R.O.C. TEL: / FAX: Documented By : ( Senior Adm. Specialist / Genie Chang ) Reviewed By : ( Engineer / Elvis Su ) Approved By : ( Manager / Vincent Lin ) Page: 2 of 35

4 Laboratory Information We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted (audited or listed) by the following related bodies in compliance with ISO 17025, EN and specified testing scopes: Taiwan R.O.C. : BSMI, NCC, TAF Germany : TUV Rheinland Norway : Nemko, DNV USA : FCC, NVLAP Japan : VCCI The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation s Web Site : The address and introduction of QuieTek Corporation s laboratories can be founded in our Web site : If you have any comments, Please don t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL: / FAX: service@quietek.com LinKou Testing Laboratory : No. 5, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL : / FAX : service@quietek.com Suzhou (China) Testing Laboratory : No. 99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou,China. TEL : / FAX : service@quietek.com Page: 3 of 35

5 TABLE OF CONTENTS Description Page 1. General Information EUT Description Mode of Operation Tested System Details Configuration of Tested System EUT Exercise Software Technical Test Summary of Test Result List of Test Equipment Measurement Uncertainty Test Environment Conducted Emission Test Specification Test Setup Limit Test Procedure Test Result Test Photograph Radiated Emission Test Specification Test Setup Limit Test Procedure Test Result Test Photograph Attachment EUT Photograph Page: 4 of 35

6 1. General Information 1.1. EUT Description Product Name Trade Name Model No. TCF-142-RM Series/Rack Chassis Moxa TCF-142-S-SC-RM, TCF-142-S-ST-RM, TCF-142-M-SC-RM, TCF-142-M-ST-RM, TRC-190-DC-48 Component Signal Cable*3 Non-Shielded, 0.8m Fiber Cable*19 Non-Shielded, 2.0m Note: 1. This appendix report was based on Quietek report No. 08A198R-ITUSP02V The EUT is including five models and the different is AC change DC and each of model is shown as below: Model Number Description TCF-142-S-SC-RM, TCF-142-S-ST-RM, TCF-142-M-SC-RM, TCF-142-M-ST-RM TRC-190-DC-48 Fiber transceiver type difference One power module (Redundant power) Page: 5 of 35

7 1.2. Mode of Operation QuieTek has verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: Pre-Test Mode Mode 1: Normal Operation Final Test Mode Emission Mode 1: Normal Operation Page: 6 of 35

8 1.3. Tested System Details The types for all equipments, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord 1 Printer EPSON StyLus C63 FAPY Non-Shielded, 1.8m 2 Mouse HP M-S69 N/A N/A 3 Mouse COMPAQ KB-0133 B55940MGAPK00K N/A 4 Microphone & PCHOME N/A N/A N/A Earphone 5 Walkman AIWA HS-TA164 N/A N/A 6 Modem ACEEX DM Non-Shielded, 1.8m 7 LCD Monitor CMV CT-730D FNC122F57CA0965 Non-Shielded, 1.8m 8 PC CPU Intel Intel(R) Celeron(R) Non-Shielded, 1.8m CPU2.8G M/B ASUS P4S800-MX SE REV1.03 HDD Seagate ST AS DVD-ROM ASUS DVD-E616A2 S.P.S SevenTeam ST-460EAD-05F DDR Kingston KVR400X64C3A, 512MB Page: 7 of 35

9 1.4. Configuration of Tested System Connection Diagram Signal Cable Type Signal cable Description A Printer Cable Shielded, 1.2m B Fiber Cable Non-Shielded, 2.0m, nineteen PCS. C RS-232 Cable Shielded, 1.5m, five PCS. D Signal Cable Shielded, 0.8m, three PCS. E Mouse Cable Shielded, 1.8m F Microphone & Earphone Cable Shielded, 1.6m G Keyboard Cable Shielded, 1.8m H Audio Cable Non-Shielded, 1.6m I RS-232 Cable Shielded, 1.5m J D-SUB Cable Shielded, 1.8m with two ferrite cores boned. Page: 8 of 35

10 1.5. EUT Exercise Software 1 Setup the EUT and simulators as shown on Turn on the power of all equipment. 3 A mufti meter was used to verify the model operation before the measurement. Page: 9 of 35

11 2. Technical Test 2.1. Summary of Test Result No deviations from the test standards Deviations from the test standards as below description: Emission Performed Item Normative References Test Performed Deviation Conducted Emission FCC CFR Title 47 Part 15 Subpart B: 2008 Class A Yes No ANSI C63.4: 2003 Radiated Emission FCC CFR Title 47 Part 15 Subpart B: 2008 Class A Yes No ANSI C63.4: 2003 Page: 10 of 35

12 2.2. List of Test Equipment Conducted Emission / SR1 Instrument Manufacturer Type No. Serial No Cal. Date EMI Test Receiver R&S ESCS /10/20 LISN R&S ENV / /08/14 LISN R&S ENV /02/17 Pulse Limiter R&S ESH3-Z /09/09 Radiated Emission / Site2 Instrument Manufacturer Type No. Serial No Cal. Date Bilog Antenna Schaffner Chase CBL6112B /09/15 Broadband Horn Antenna Schwarzbeck BBHA /07/25 EMI Test Receiver R&S ESCS /03/23 Horn Antenna Schwarzbeck BBHA9120D /08/10 Pre-Amplifier QTK N/A N/A 2009/01/03 Spectrum Analyzer Advantest R /04/06 Page: 11 of 35

13 2.3. Measurement Uncertainty Conducted Emission The measurement uncertainty is evaluated as ± 2.26 db. Radiated Emission The measurement uncertainty is evaluated as ± 3.19 db. Page: 12 of 35

14 2.4. Test Environment Performed Item Items Required Actual Temperature ( C) Conducted Emission Humidity (%RH) Barometric pressure (mbar) Temperature ( C) Radiated Emission Humidity (%RH) Barometric pressure (mbar) Page: 13 of 35

15 3. Conducted Emission 3.1. Test Specification According to Standard : FCC Part 15 Subpart B, ANSI C Test Setup 3.3. Limit Limits Frequency (MHz) QP (dbuv) AV (dbuv) Remarks: In the above table, the tighter limit applies at the band edges. Page: 14 of 35

16 3.4. Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refers to the block diagram of the test setup and photographs.) Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed on conducted measurement. Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz. Page: 15 of 35

17 3.5. Test Result Site : SR1 Time : 2009/08/13-13:08 Limit : CISPR_A_00M_QP Margin : 10 EUT : TCF-142-RM Series/Rack Chassis Probe : 8226_176(+) - Line1 Power : DC 48V Note : Mode 1 Page: 16 of 35

18 Site : SR1 Time : 2009/08/13-13:10 Limit : CISPR_A_00M_QP Margin : 0 EUT : TCF-142-RM Series/Rack Chassis Probe : 8226_176(+) - Line1 Power : DC 48V Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv) (db) (dbuv) QUASIPEAK QUASIPEAK QUASIPEAK 4 * QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 17 of 35

19 Site : SR1 Time : 2009/08/13-13:10 Limit : CISPR_A_00M_AV Margin : 0 EUT : TCF-142-RM Series/Rack Chassis Probe : 8226_176(+) - Line1 Power : DC 48V Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv) (db) (dbuv) AVERAGE AVERAGE AVERAGE 4 * AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 18 of 35

20 Site : SR1 Time : 2009/08/13-13:11 Limit : CISPR_A_00M_QP Margin : 10 EUT : TCF-142-RM Series/Rack Chassis Probe : 8226_177(-) - Line1 Power : DC 48V Note : Mode 1 Page: 19 of 35

21 Site : SR1 Time : 2009/08/13-13:13 Limit : CISPR_A_00M_QP Margin : 0 EUT : TCF-142-RM Series/Rack Chassis Probe : 8226_177(-) - Line1 Power : DC 48V Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv) (db) (dbuv) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 6 * QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 20 of 35

22 Site : SR1 Time : 2009/08/13-13:13 Limit : CISPR_A_00M_AV Margin : 0 EUT : TCF-142-RM Series/Rack Chassis Probe : 8226_177(-) - Line1 Power : DC 48V Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv) (db) (dbuv) AVERAGE AVERAGE AVERAGE AVERAGE AVERAGE 6 * AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 21 of 35

23 3.6. Test Photograph Test Mode : Mode 1: Normal Operation Description : Front View of Conducted Test Test Mode : Mode 1: Normal Operation Description : Back View of Conducted Test Page: 22 of 35

24 4. Radiated Emission 4.1. Test Specification According to EMC Standard : FCC Part 15 Subpart B, ANSI C Test Setup Under 1GHz Test Setup: Above 1GHz Test Setup: Page: 23 of 35

25 4.3. Limit Under 1GHz test shall not exceed the following value: Frequency (MHz) Limits Distance (m) dbuv/m Remark: 1. The tighter limit shall apply at the edge between two frequency bands. 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Above 1GHz test shall not exceed the following value: FCC Part 15 Subpart B Paragraph Limits (dbuv/m) Frequency (MHz) Distance(m) dbuv/m Above Remark: 1. The tighter limit shall apply at the edge between two frequency bands. 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. 3. RF Voltage (dbuv/m) = 20 log RF Voltage (uv/m) Page: 24 of 35

26 4.4. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level and the antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated on radiated measurement. For an unintentional radiator, including a digital device, the spectrum shall be investigated from the lowest radio frequency signal generated or used in the device, without going below the lowest frequency for which a radiated emission limit is specified, up to the frequency shown in the folowing table: Highest frequency generated or used in the device or on which the device operates or tunes (MHz) Upper frequency of measurement range (MHz) Below th harmonic of the highest Above 1000 frequency or 40 GHz, whichever is lower On any frequency or frequencies below or equal to 1000 MHz, the radiated limits shown are based on measuring equipment employing a quasi-peak detector function and above 1000 MHz, the radiated limits shown are based measuring equipment employing an average detector function. When average radiated emission measurement are included emission measurement Above 1000 MHz, there also is a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 db above the maximum permitted average limit. For class A, the measurement distance between the EUT and antenna is 10 meters for under 1GHz and above 1GHz. For class B, the measurement distance between the EUT and antenna is 10 meters for under 1GHz and 3 meters for above 1GHz. The bandwidth below 1GHz setting on the field strength meter (R&S Test Receiver ESCS 30) is 120 khz and above 1GHz is 1MHz. Page: 25 of 35

27 4.5. Test Result Site : OATS-2 Time : 2009/08/11-15:39 Limit : CISPR_A_10M_QP Margin : 6 EUT : TCF-142-RM Series/Rack/Chassis Probe : Site2_CBL6112_10M_ HORIZONTAL Power : DC 48V Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv/m) (db) (dbuv/m) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 7 * QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 26 of 35

28 Site : OATS-2 Time : 2009/08/11-15:29 Limit : CISPR_A_10M_QP Margin : 6 EUT : TCF-142-RM Series/Rack/Chassis Probe : Site2_CBL6112_10M_ VERTICAL Power : DC 48V Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv/m) (db) (dbuv/m) 1 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 27 of 35

29 Site : OATS-2 Time : 2009/05/28-04:45 Limit : FCC_A_(Above_1G)_3M_PK Margin : 6 EUT : TCF-142-RM Series/Rack Chassis Probe : 9120D_1-18G_Horn - HORIZONTAL Power : DC 48V Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv/m) (db) (dbuv/m) PEAK 2 * PEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 28 of 35

30 Site : OATS-2 Time : 2009/05/28-04:52 Limit : FCC_A_(Above_1G)_3M_PK Margin : 6 EUT : TCF-142-RM Series/Rack Chassis Probe : 9120D_1-18G_Horn - VERTICAL Power : DC 48V Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv/m) (db) (dbuv/m) PEAK 2 * PEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 29 of 35

31 4.6. Test Photograph Test Mode : Mode 1: Normal Operation Description : Front View of Radiated Test Test Mode : Mode 1: Normal Operation Description : Back View of Radiated Test Page: 30 of 35

32 Test Mode : Mode 1: Normal Operation Description : Front View of High Frequency Radiated Test Page: 31 of 35

33 5. Attachment EUT Photograph (1) EUT Photo (2) EUT Photo Page: 32 of 35

34 (3) EUT Photo (4) EUT Photo Page: 33 of 35

35 (5) EUT Photo (6) EUT Photo Page: 34 of 35

36 (7) EUT Photo (8) EUT Photo Page: 35 of 35