RF Test Report. Report No.: AGC EE10. TEST NAME : 1999/5/EC R&TTE Directive Art.3.2 STANDARD(S) : EN V : V1.

Transcription

1 Page 1 of 49 RF Test Report Report No.: AGC EE10 TEST NAME : 1999/5/EC R&TTE Directive Art.3.2 PRODUCT DESIGNATION : ihere3.0 BRAND NAME : ihere3.0 MODEL NAME : ihere3.0 CLIENT : No NDA Inc. DATE OF ISSUE : Feb.24,2016 STANDARD(S) : EN V REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.

2 Page 2 of 49 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Feb.24,2016 Valid Original Report

3 Page 3 of 49 TABALE OF CONTENTS TABALE OF CONTENTS TEST RESULT CERTIFICATION TECHNICAL INFORMATION EUT DESCRIPTION SUPPORT EQUIPMENT DESCRIPTION OF TEST MODES DETAILS OF TEST IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION LIST OF TEST EQUIPMENTS ENVIRONMENTAL CONDITIONS MEASUREMENT UNCERTAINTY ETSI EN REQUIREMENTS RF OUTPUT POWER POWER SPECTRAL DENSITY DUTY CYCLE, TX-SEQUENCE, TX-GAP MEDIUM UTILISATION (MU) FACTOR ADAPTIVITY (CHANNEL ACCESS MECHANISM) OCCUPIED CHANNEL BANDWIDTH TRANSMITTER UNWANTED EMISSIONS IN THE OUT OF BAND DOMAIN TRANSMITTER SPURIOUS EMISSIONS RECEIVER SPURIOUS EMISSIONS RECEIVER BLOCKING APPENDIX A PHOTOGRAPHS OF THE TEST SETUP APPENDIX B PHOTOGRAPHS OF THE EUT... 44

4 Page 4 of TEST RESULT CERTIFICATION Applicant Name: Address: Manufacturer Name: Address: Product Designation: Brand Name: Test Model Date of test No NDA Inc. 828 Bryant St. Palo Alto, CA 94301, USA No NDA Inc. 828 Bryant St. Palo Alto, CA 94301, USA ihere3.0 ihere3.0 ihere3.0 Feb.16,2016 to Feb.18,2016 We (AGC), Attestation of Global Compliance (Shenzhen) Co., Ltd. for compliance with the requirements set forth in the European Standard ETSI EN V The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Tested By Time Huang(Huang Nanhui) Feb.24,2016 Reviewed By Forrest Lei(Lei Yonggang) Feb.24,2016 Approved By Solger Zhang(Zhang Hongyi) Authorized Officer Feb.24,2016

5 Page 5 of TECHNICAL INFORMATION 2.1 EUT DESCRIPTION Bluetooth Version V 4.0 Modulation GFSK Hardware Version V1.0 Software Version V1.0 Adaptive / non-adaptive equipment The number of Hopping Frequencies The maximum RF Output Power (e.i.r.p.) The different transmit operating modes Operating Frequency Range(s) Type of Equipment Antenna designation Antenna gain Nominal voltages The extreme operating conditions Adaptive Equipment 40 Channel(37 Hopping Channel,3advertising Channel) -1.75dBm Operating mode 1: Single Antenna Equipment Equipment with only 1 antenna 2402MHz~2480MHz Stand-alone Ceramic Antenna 0dBi DC 3.7V by battery Operating temperature range: -20 C~55 C Note: 1. The above information was declared by the applicant. 2. The equipment submitted are representative production models. 3. The EUT provides Bluetooth wireless interface operating at 2.4G ISM band (2402MHZ-2480MHZ). 4. Only the Bluetooth was tested according the standard requirement. 5. The EUT is an adaptive equipment and hand-portable station according to ETSI EN v Please refer to Appendix Ⅰ for the photographs of the EUT. For more details, please refer to the User s manual of the EUT.

6 Page 6 of SUPPORT EQUIPMENT Item Equipment Mfr/Brand Model/Type No. Remark 1 PC APPLE A1465 A.E 2.3 DESCRIPTION OF TEST MODES NO. TEST MODE DESCRIPTION 1 Low channel TX 2 Middle channel TX 3 High channel TX 4 Low channel RX 5 Middle channel RX 6 High channel RX Note: All the test modes can be supply by battery, only the result of the worst case was recorded in the report if no any records.

7 Page 7 of 49 A) OBJECTIVE Perform Radio Spectrum tests for CE Marking according to the provisions of article 3.2 of the R&TTE Directive (1999/5/EC) for the Bluetooth function of the EUT. B) TEST STANDARDS AND RESULTS The EUT has been tested according to ETSI EN V1.9.1 ( ). ETSI EN V1.9.1 ( ) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems;data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive TEST ITEMS AND THE RESULTS ARE AS BELOW: Basic Standard Test Type The worst case operational mode Result 1 ETSI EN RF Output Power Mode 1/2/3 Pass 2 ETSI EN Power Spectral Density Mode 1/2/3 Pass 3 ETSI EN Duty Cycle, Tx-sequence, Tx-gap N/A N/A 4 ETSI EN Medium Utilisation (MU) factor N/A N/A 5 ETSI EN Adaptivity (adaptive equipment using modulations other than FHSS) N/A N/A 6 ETSI EN Occupied Channel Bandwidth Mode 1/3 Pass 7 ETSI EN Transmitter unwanted emissions in the out-of-band domain Mode 1/3 Pass 8 ETSI EN Transmitter unwanted emissions in the spurious domain Mode 1/3 Pass 9 ETSI EN Receiver spurious emissions Mode 4/6 Pass 10 ETSI EN Receiver Blocking N/A N/A 11 ETSI EN Geo-location capability N/A N/A Note: 1. N/A means it s not applicable to this item. 2. Owing to the maximum declared RF Output power (e.i.r.p.) less than 10 dbm, so the item 3, 4, 5, 10 are not applicable.

8 Page 8 of 49 3 DETAILS OF TEST 3.1 IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION Company Name: Address: Attestation of Global Compliance (Shenzhen) Co., Ltd. 2/F., Building 2, No.1-No.4, Chaxi Sanwei Technical Industrial Park, Gushu, Xixiang, Bao'an District, Shenzhen, Guangdong, China 3.2 LIST OF TEST EQUIPMENTS Description Manufacturer Model No. S/N Calibration Date Calibration Due. SIGNAL ANALYZER Agilent N9020A MY Oct. 21, 2015 Oct. 20,2016 SIGNAL GENERATOR Agilent N5182A MY Oct. 21, 2015 Oct. 20,2016 SIGNAL GENERATOR Agilent E8257D MY Dec. 04,2015 Dec.03,2016 USB Wideband Power Sensor USB Wideband Power Sensor USB Wideband Power Sensor USB Wideband Power Sensor USB Simultaneous Sampl ing Multifunction DAQ Agilent U2021XA MY Oct. 24, 2015 Oct. 23, 2016 Agilent U2021XA MY Oct. 24, 2015 Oct. 23, 2016 Agilent U2021XA MY Oct. 24, 2015 Oct. 23, 2016 Agilent U2021XA MY Oct. 24, 2015 Oct. 23, 2016 Agilent U2531A MY Oct. 24, 2015 Oct. 23, GHz Filter Micro-Tronics BRM Mar. 06, 2015 Mar. 05, 2016 Spectrum Analyzer Agilent E4440A US July 25, 2015 July 24, 2016 WIDEBAND REQUENCY ANTENNA Horn Antenna SCHWARZBEC K EM VULB9168 VULB Mar.20, 2015 Mar.19, 2016 EM-AH Mar.12, 2015 Mar.11, 2016 Amplifier EM EM Mar.06, 2015 Mar.05, ENVIRONMENTAL CONDITIONS During the measurement the environmental conditions were within the listed ranges: - Temperature: 15-35ºC - Humidity: % - Atmospheric pressure: kpa

9 Page 9 of MEASUREMENT UNCERTAINTY The uncertainty is calculated using the methods suggested in the Guide to the Expression of Uncertainty in Measurement (GUM) published by ISO. - Uncertainty of Radio Frequency, Uc=±1 x Uncertainty of total RF power, conducted, Uc = ±1.5dB - Uncertainty of RF power density, conducted, Uc = ±3dB - Uncertainty of spurious emissions, conducted, Uc = ±3dB - Uncertainty of all emissions, radiated, Uc = ±6dB - Uncertainty of Temperature: ±1 C - Uncertainty of Humidity: ±5 % - Uncertainty of DC and low frequency voltages: ±3 % 4. ETSI EN REQUIREMENTS 4.1 RF OUTPUT POWER EN Clause For adaptive equipment using wide band modulations other than FHSS, the maximum RF output power shall be 20 dbm. The maximum RF output power for non-adaptive equipment shall be declared by the supplier and shall not exceed 20 dbm. See clause m). For non-adaptive equipment using wide band modulations other than FHSS, the maximum RF output power shall be equal to or less than the value declared by the supplier. This limit shall apply for any combination of power level and intended antenna assembly. Test Configuration Remarks: EUT was direct connected to test equipment through coupling device. TEST PROCEDURE 1. Please refer to ETSI EN (V1.9.1) clause for the test conditions. 2. Please refer to ETSI EN (V1.9.1) clause for the measurement method.

10 Page 10 of 49 TEST RESULTS Operation Mode: TX Test Date: Feb.24,2016 Temperature: 25 o C Tested by: Time Huang Humidity: 55 % RH Detector: RMS Number of Burst = 10 Measurement Time TEST CONDITIONS = 45.53ms GFSK MODULATION RF OUTPUT POWER (dbm) Temp (25) C Temp (-20) C Temp (55) C Result DC 3.7V DC 3.7V DC 3.7V Low Channel TX Middle Channel TX High Channel TX Limit 20dBm Low Channel

11 Page 11 of 49 Middle Channel High Channel Note: Result=Reading+ Ant. Gain The reading value included cable loss. The diagrams are for normal temperature. Conclusion: PASS

12 Page 12 of POWER SPECTRAL DENSITY EN Clause For wide band modulations other than the FHSS, The maximum E.I.R.P Power density is limited to 10mW Per MHz TEST PROCEDURE 1. Please refer to ETSI EN (V1.9.1) clause for the test conditions. 2. Please refer to ETSI EN (V1.9.1) clause for the measurement method. 3 The equipment setting as following Start Frequency: MHz Stop Frequency: 2 483,5 MHz Resolution BW: 10 khz Video BW: 30 khz Sweep Points: >8350 Detector: RMS Trace Mode: Max Hold Sweep time: Auto

13 Page 13 of 49 TEST RESULTS PEAK POWER DENSITY Channel Tested Power Density (dbm/mhz) Test Limit (dbm/mhz) Pass / Fail Low Channel TX Pass Middle Channel TX Pass High Channel TX Pass Low Channel Middle Channel

14 High Channel Report No.: AGC EE10 Page 14 of 49

15 Page 15 of DUTY CYCLE, TX-SEQUENCE, TX-GAP ETSI EN SUBCLAUSE The Duty Cycle shall be equal to or less than the maximum value declared by the supplier. The maximum Tx-sequence Time and the minimum Tx-gap Time shall be according to the formula below: Maximum Tx-Sequence Time = Minimum Tx-gap Time = M where M is in the range of 3,5 ms to 10 ms. TEST CONFIGURATION Monopole Antenna EUT Spectrum analyzer (See Note) TEST PROCEDURE 1. Please refer to ETSI EN (V1.9.1) clause for the test conditions. 2. Please refer to ETSI EN (V1.9.1) clause the measurement method. TEST RESULT N/A

16 Page 16 of MEDIUM UTILISATION (MU) FACTOR ETSI EN SUBCLAUSE The Medium Utilisation (MU) factor is a measure to quantify the amount of resources (Power and Time) used by non-adaptive equipment. The Medium Utilisation factor is defined by the formula: MU = (P/100 mw) DC where: MU is Medium Utilisation factor in %. P is the RF output power as defined in clause expressed in mw. DC is the Duty Cycle as defined in clause expressed in %. NOTE: The equipment may have dynamic behaviour with regard to duty cycle and corresponding power level. TEST CONFIGURATION Monopole Antenna EUT Spectrum analyzer (See Note) TEST PROCEDURE 1. Please refer to ETSI EN (V1.9.1) clause for the test conditions. 2. Please refer to ETSI EN (V1.9.1) clause the measurement method. TEST RESULT N/A

17 Page 17 of ADAPTIVITY (CHANNEL ACCESS MECHANISM) ETSI EN SUBCLAUSE This requirement does not apply to non-adaptive equipment or adaptive equipment operating in a non-adaptive mode providing the equipment complies with the requirements and/or restrictions applicable to non-adaptive equipment. In addition, this requirement does not apply for equipment with a maximum declared RF Output power level of less than 10 dbm e.i.r.p. or for equipment when operating in a mode where the RF Output power is less than 10 dbm e.i.r.p. Adaptive equipment using modulations other than FHSS is allowed to operate in a non-adaptive mode providing it complies with the requirements applicable to non-adaptive equipment. An adaptive equipment using modulations other than FHSS is equipment that uses a mechanism by which it can adapt to its environment by identifying other transmissions present within its Occupied Channel Bandwidth. Adaptive equipment using modulations other than FHSS shall implement either of the Detect and Avoid mechanisms provided in clauses or Adaptive systems are allowed to switch dynamically between different adaptive modes. TEST CONFIGURATION TEST PROCEDURE 1. Please refer to ETSI EN (V1.9.1) clause for the test conditions. 2. Please refer to ETSI EN (V1.9.1) clause the measurement method.. TEST RESULT N/A

18 Page 18 of OCCUPIED CHANNEL BANDWIDTH ETSI EN SUBCLAUSE The Occupied Channel Bandwidth shall fall completely within the band given in clause 1. In addition, for non-adaptive systems using wide band modulations other than FHSS and with e.i.r.p greater than 10 dbm, the occupied channel bandwidth shall be less than 20 MHz. CONFIGURATION TEST PROCEDURE 1. Please refer to ETSI EN (V1.9.1) clause for the test conditions. 2. Please refer to ETSI EN (V1.9.1) clause the measurement method. 3. The Test equipment information as following Centre frequency: 2402MHz,2480MHz Resolution bandwidth: 20kHz Video bandwidth: 62kHz Detector mode :RMZ Trace mode :Max Hold TEST RESULT TEST ITEM TEST MODE OCCUPIED CHANNEL BANDWIDTH GFSK MODULATION MEASUREMENT RESULT Test Data (MHz) Criteria Low Channel 1.02 PASS High Channel 1.02 PASS Conclusion: PASS

19 Page 19 of 49 Low Channel High Channel

20 Page 20 of TRANSMITTER UNWANTED EMISSIONS IN THE OUT OF BAND DOMAIN ETSI EN SUBCLAUSE TEST CONFIGURATION For have temporary antenna connector product

21 Page 21 of 49 Antenna tower EUT 3m 4m Horn antenna Spectrum analyzer Turntable 1.5m 1m Pre-amp For have no temporary antenna product TEST PROCEDURE 1. Please refer to ETSI EN (V1.9.1) clause for the test conditions. 2. Please refer to ETSI EN (V1.9.1) clause the measurement method. TEST RESULT

22 Page 22 of 49 NORMAL TEMPERATURE NORMAL VOLTAGE Channel Antenna Freq(MHz) Level Limit CH Low-2402 Antenna CH Low-2402 Antenna Channel Antenna Freq(MHz) Level Limit CH High-2480 Antenna CH High-2480 Antenna

23 Page 23 of 49 LOW TEMPERATURE NORMAL VOLTAGE Channel Antenna Freq(MHz) Level Limit CH Low-2402 Antenna CH Low-2402 Antenna Channel Antenna Freq(MHz) Level Limit CH High-2480 Antenna CH High-2480 Antenna

24 Page 24 of 49 HIGH TEMPERATURE NORMAL VOLTAGE Channel Antenna Freq(MHz) Level Limit CH Low-2402 Antenna CH Low-2402 Antenna Channel Antenna Freq(MHz) Level Limit CH High-2480 Antenna CH High-2480 Antenna Note: The modulation used during test is GFSK Conclusion: PASS

25 Page 25 of TRANSMITTER SPURIOUS EMISSIONS ETSI EN SUBCLAUSE Spurious emissions are emissions outside the frequency range(s) of the equipment as defined in Clause Transmitter unwanted emissions in the spurious domain are emissions outside the allocated band and outside the out-of-band domain as indicated in figure 1 when the equipment is in Transmit mode. The spurious emissions of the transmitter shall not exceed the values in tables in the indicated bands: Frequency Range Maximum Power Bandwidth e.r.p(<=1ghz)/e.i.r.p(>1ghz) 30MHZ to 47MHZ -36dBm 100kHz 47MHZ to 74MHZ -54dBm 100kHz 74MHZ to 87.5MHZ -36dBm 100kHz 87.5MHZ to 118MHZ -54dBm 100kHz 118MHZ to 174MHZ -36dBm 100kHz 174 MHZ to 230MHZ -54dBm 100kHz 230 MHZ to 470MHZ -36dBm 100kHz 470 MHZ to 862MHZ -54dBm 100kHz 862 MHZ to 1GHZ -36dBm 100kHz 1 GHZ to 12.75GHZ -30dBm 1MHz

26 Page 26 of 49 Test Configuration Below 1GHz Antenna tower EUT 3m 4m Bi-log or Loop antenna Spectrum analyzer Turntable 1.5m 1m Reference ground plane Above 1GHz Antenna tower EUT 3m 4m Horn antenna Spectrum analyzer Turntable 1.5m 1m Pre-amp

27 Page 27 of 49 Radiated Method Conducted Method TEST PROCEDURE 1. Please refer to ETSI EN (V1.9.1) clause for the conducted method. 2. Please refer to ETSI EN (V1.9.1) clause for the radiated method. TEST RESULTS FOR RADIATED METHOD(N/A) TEST SETTING The emissions over the range 30 MHz to MHz shall be identified. Spectrum analyser settings: Resolution bandwidth: 100 khz Video bandwidth: 300 khz Detector mode: Peak Trace Mode: Max Hold Sweep Points: The emissions over the range 1 GHz to 12,75 GHz shall be identified. Spectrum analyser settings: Resolution bandwidth: 1 MHz Video bandwidth: 3 MHz Detector mode: Peak Trace Mode: Max Hold Sweep Points: Sweep time [μs] / (1 μs) with a maximum of

28 Page 28 of 49 TEST RESULTS CONDUCTED RESULTS: (Low channel)

29 Page 29 of 49 (High channel) Conclusion: PASS

30 Page 30 of 49 TEST RESULTS FOR RADIATED METHOD Low Channel: Transmitter Spurious Emission below 1GHz (30MHz-1GHz) Frequency (MHz) Reading Level (dbuv/m) Antenna Polarizati on S.G. Cable Loss Ant.Gain Emission Level Limit Margin (dbm) (db) (dbi) (dbm) (dbm) (db) V V V V V V H H H H H H

31 Page 31 of 49 High Channel: Transmitter Spurious Emission below 1GHz (30MHz-1GHz) Frequency (MHz) Reading Level (dbuv/m) Antenna Polarizati on S.G. Cable Loss Ant.Gain Emission Level Limit Margin (dbm) (db) (dbi) (dbm) (dbm) (db) V V V V V V H H H H H H Note: The margins of the other spectrum below 1GHz are not exceeding the minimum value of margin, and this part of the results without recording in the test report.

32 Page 32 of 49 Low Channel: Transmitter Spurious Emission above 1GHz (1GHz-12.75GHz) Frequency (MHz) Reading Level (dbuv) Antenna Polarizati on S.G. Cable Loss Ant.Gain Emission Level Limit Margin (dbm) (db) (dbi) (dbm) (dbm) (db) V V V V V V H H H H H H Note: The margins of the other spectrum above 1GHz are not exceeding the minimum value of margin, and this part of the results without recording in the test report.

33 Page 33 of 49 High Channel: Transmitter Spurious Emission above 1GHz (1GHz-12.75GHz) Frequency Reading Level Antenna S.G. Cable Loss Ant.Gain Emission Level Limit Margin (MHz) (dbuv) Polarizati on (dbm) (db) (dbi) (dbm) (dbm) (db) V V V V V V H H H H H H Note: 1.The margins of the other spectrum above 1GHz are not exceeding the minimum value of margin, and this part of the results without recording in the test report. 2. The emission behaviour belongs to narrowband spurious emission. 3. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with -- remark, if no specific emission from the EUT are recorded (ie: margin>20db from the applicable limit) and considered that s already beyond the background noise floor. Conclusion: PASS

34 Page 34 of RECEIVER SPURIOUS EMISSIONS ETSI EN SUBCLAUSE Receiver spurious emissions are emissions at any frequency when the equipment is in receive mode. The spurious emissions of the receiver shall not exceed the values given in table 5. TEST CONFIGURATION Radiated Spurious Emissions: Same as section 4.4 in this test report TEST PROCEDURE 1. Please refer to ETSI EN clause for the test conditions. 2. Please refer to ETSI EN clause for the measurement methods. TEST RESULTS FOR RADIATED METHOD (N/A)

35 Page 35 of 49 TEST RESULTS FOR CONDUCTED METHOD RECEIVER MODE (Low channel) Freq (MHz) RMS Level Limit (dbm) Over Limit (db) Status (dbm) Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass

36 Page 36 of 49 RECEIVER MODE (High channel) Freq (MHz) RMS Level Limit (dbm) Over Limit (db) Status (dbm) Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass

37 Conclusion: PASS Report No.: AGC EE10 Page 37 of 49

38 Page 38 of 49 TEST RESULTS FOR RADIATED METHOD Low Channel: Receiver Spurious Emission below 1GHz (30MHz-1GHz) Frequency (MHz) Reading Level (dbuv) Antenna Polarizati on S.G. Cable Loss Ant.Gain Emission Level Limit Margin (dbm) (db) (dbi) (dbm) (dbm) (db) V V V V V V H H H H H H

39 Page 39 of 49 High Channel: Receiver Spurious Emission below 1GHz (30MHz-1GHz) Frequency (MHz) Reading Level (dbuv) Antenna Polarizati on S.G. Cable Loss Ant.Gain Emission Level Limit Margin (dbm) (db) (dbi) (dbm) (dbm) (db) V V V V V V H H H H H H Note: The margins of the other spectrum below 1GHz are not exceeding the minimum value of margin, and this part of the results without recording in the test report.

40 Page 40 of 49 Low Channel: Receiver Spurious Emission above 1GHz (1GHz-12.75GHz) Frequency (MHz) Reading Level (dbuv) Antenna Polarizati on S.G. Cable Loss Ant.Gain Emission Level Limit Margin (dbm) (db) (dbi) (dbm) (dbm) (db) V V V V V V H H H H H H

41 Page 41 of 49 High Channel: Receiver Spurious Emission above 1GHz (1GHz-12.75GHz) Frequency Reading Level Antenna S.G. Cable Loss Ant.Gain Emission Level Limit Margin (MHz) (dbuv) Polarizati on (dbm) (db) (dbi) (dbm) (dbm) (db) V V V V V V H H H H H H Note: 1.The margins of the other spectrum above 1GHz are not exceeding the minimum value of margin, and this part of the results without recording in the test report. 2. The emission behaviour belongs to narrowband spurious emission. 3. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with -- remark, if no specific emission from the EUT are recorded (ie: margin>20db from the applicable limit) and considered that s already beyond the background noise floor. Conclusion: PASS

42 Page 42 of RECEIVER BLOCKING ETSI EN SUBCLAUSE This requirement does not apply to non-adaptive equipment or adaptive equipment operating in a non-adaptive mode. In addition, this requirement does not apply for equipment with a maximum declared RF Output power level of less than 10 dbm e.i.r.p. or for equipment when operating in a mode where the RF Output power is less than 10 dbm e.i.r.p. Adaptive Frequency Hopping equipment shall comply with the requirements defined in clauses (LBT based DAA) or (non-lbt based DAA) in the presence of a blocking signal with characteristics as provided in table 3. TEST PROCEDURE 1. Please refer to ETSI EN clause for the test conditions. 2. Please refer to ETSI EN clause for the measurement methods. TEST RESULTS N/A

43 Page 43 of 49 APPENDIX A: PHOTOGRAPHS OF THE TEST SETUP CONDUCTED SPURIOUS EMISSION TEST

44 Page 44 of 49 APPENDIX B: PHOTOGRAPHS OF THE EUT TOTAL VIEW OF EUT TOP VIEW OF EUT

45 Page 45 of 49 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

46 Page 46 of 49 BACK VIEW OF EUT LEFT VIEW OF EUT

47 Page 47 of 49 RIGHT VIEW OF EUT OPEN VIEW OF EUT

48 Page 48 of 49 VIEW OF EUT (PORT) INTERNAL VIEW OF EUT-1

49 Page 49 of 49 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3 Antenna ----END OF REPORT----