Test report No. : S Page : 1 of 24 Issued date : August 23, 2018 RADIO TEST REPORT. Test Report No. : S

Transcription

1 Page : 1 of 24 RADIO TEST REPORT Test Report No. : S Applicant : TAIYO YUDEN CO., LTD. Type of Equipment : Bluetooth low energy / ANT Module Model No. : EYSLSN Test standard : EN V2.1.1 Test Result : Complied 1. This test report shall not be reproduced in full or partial, without the written approval of 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the above standard(s). 4. The test results in this report are traceable to the national or international standards. 5. This test report covers Radio technical requirements. It does not cover administrative issues such as Manual or non-radio test related Requirements. (if applicable) 6. The all test items in this test report are conducted by Shonan EMC Lab and Kashima EMC Lab. 7. The opinions and the interpretations to the result of the description in this report are outside scopes where UL Japan has been accredited. Date of test: July 23 to 27, 2018 Representative test engineer: Shiro Kobayashi Engineer Consumer Technology Division Approved by : Hikaru Shirasawa Engineer Consumer Technology Division The testing in which "Non-accreditation" is displayed is outside the accreditation scopes in UL Japan. There is no testing item of "Non-accreditation". RTL EM-F0429

2 Page : 2 of 24 REVISION HISTORY Original Test Report No.: S Revision Test report No. Date Page revised Contents -(Original) S August 23,

3 Page : 3 of 24 CONTENTS PAGE SECTION 1: Customer information... 4 SECTION 2: Equipment under test (E.U.T.)... 4 SECTION 3: Test specification, procedures & results... 5 SECTION 4: Operation of E.U.T. during testing... 8 SECTION 5: Antenna Terminal Conducted Tests APPENDIX 1: Test data RF Output Power Power Spectral Density Occupied Channel Bandwidth Transmitter unwanted emissions in the out-of-band domain Receiver Blocking APPENDIX 2: Test instruments APPENDIX 3: Photographs of test setup Antenna terminal conducted tests other than Receiver Blocking Receiver Blocking... 24

4 Page : 4 of 24 SECTION 1: Customer information Company Name : TAIYO YUDEN CO., LTD. Address : 8-1,Sakae-cho, Takasaki-shi, Gunma ,Japan Telephone Number : Facsimile Number : Contact Person : Hideki Kato SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Bluetooth low energy / ANT Module Model No. : EYSLSN Serial No. : Refer to Clause 4.2 Rating : DC 3 V (DC 1.7 V to DC 3.6 V), 0.02 A, 50 Hz Receipt Date of Sample : July 13, 2018 Country of Mass-production : Japan Condition of EUT : Engineering prototype (Not for Sale: This sample is equivalent to mass-produced items.) Modification of EUT : No Modification by the test lab 2.2 Product Description Model: EYSLSN (referred to as the EUT in this report) is a Bluetooth low energy / ANT Module. Radio Specification * Receiver category: 2 < Bluetooth (BT) Low Energy (LE) (1 Mbps, 2 Mbps) > Radio Type : Transceiver Frequency of Operation : 2402 MHz MHz Modulation : GFSK Power Supply (radio part input) : DC 1.3 V Antenna type : Monopole Antenna Antenna Gain : -3.7 dbi Operating Temperature : -40 deg. C to +105 deg. C < ANT (1 Mbps) > Radio Type : Transceiver Frequency of Operation : 2402 MHz MHz Modulation : GFSK Power Supply (radio part input) : DC 1.3 V Antenna type : Monopole Antenna Antenna Gain : -3.7 dbi Operating Temperature : -40 deg. C to +105 deg. C < Nordic Original (2 Mbps) > Radio Type : Transceiver Frequency of Operation : 2402 MHz MHz Modulation : GFSK Power Supply (radio part input) : DC 1.3 V Antenna type : Monopole Antenna Antenna Gain : -3.7 dbi Operating Temperature : -40 deg. C to +105 deg. C

5 Page : 5 of 24 SECTION 3: Test specification, procedures & results 3.1 Test Specification Radio : EN V2.1.1 Title : Wideband transmission systems; Data transmission equipment operating in the 2.4GHz ISM band and using wide band modulation techniques; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU Purpose of test : Compliance with the harmonized RE directive 2014/53/EU. 3.2 Procedures and results No. Item Test Procedure Limit Remarks Worst margin Exclusions Results 1 RF output power Clause Clause Conducted See Data N/A Complied 2 Power Spectral Density Clause Clause Conducted See Data N/A Complied 3 Duty cycle, Tx-sequence, Tx-gap Clause Clause Conducted - N/A N/A*1) 4 Medium Utilisation (MU) factor Clause Clause Conducted - N/A N/A*1) 5 Adaptivity (adaptive equipment using modulations other than FHSS) Clause Clause Conducted - N/A N/A*2) 6 Occupied Channel Clause Clause Conducted See Data N/A Complied Bandwidth 7 Transmitter unwanted Clause Clause Conducted See Data N/A Complied emissions in the out-of-band domain 8 Transmitter unwanted Clause Clause Radiated - N/A N/A*3) emissions in the spurious domain 9 Receiver Clause Clause Radiated - N/A N/A*3) Spurious emissions 10 Transmitter unwanted Clause Clause Conducted - N/A emissions in the N/A*3) spurious domain 11 Receiver Clause Clause Conducted - N/A Spurious emissions N/A*3) 12 Receiver Blocking Clause Clause Conducted See Data N/A Complied 13 Geo-location - Clause N/A N/A*4) capability Note: s EMI Work Procedure 13-EM-W0420. *1) The test is not applicable since the EUT is an adaptive equipment and does not operate in a non-adaptive mode. *2) The test is not applicable since the RF output power of the EUT is less than 10 dbm (e.i.r.p.). *3) The test has not been performed according to the customer s request. *4) The EUT does not have Geo-location capability. Symbols: Complied The data of this test item has enough margin, more than the measurement uncertainty. Complied# The data of this test item meets the limits unless the measurement uncertainty is taken into consideration.

6 Page : 6 of Additions or deviations to standards No addition, exclusion nor deviation has been made from the standard. 3.4 Uncertainty The following uncertainties have been calculated to provide a confidence level of 95 % using a coverage factor k = 2. Substitution measurement (EUT height: 1.5 m, Distance: 3 m) Frequency range Uncertainty (+/-) 30 MHz MHz 4.8 db 200 MHz MHz 3.6 db 1 GHz GHz 4.4 db Antenna terminal test Uncertainty (+/-) Power Measurement above 1 GHz (Average Detector)_SPM db Power Measurement above 1 GHz (Average Detector)_SPM db Power Measurement above 1 GHz (Average Detector)_SPM-08, 09, 10, db Power Measurement above 1 GHz (Average Detector)_SPM db Conducted emissions Measurement (below 1 GHz) 1.8 db Conducted emissions Power Density Measurement (1 GHz-3 GHz) 1.7 db Conducted emissions Measurement (3 GHz-18 GHz) 2.5 db Conducted emissions Measurement (18 GHz-26.5 GHz) 2.5 db Frequency Measurement (Spectrum Analyzer) 2.1 x 10^-7 Bandwidth Measurement 1.01 % Duty cycle and Time Measurement % Temperature 0.95 deg.c. Voltage 0.24 % Humidity 3.4 % Receiver Blocking (Wanted RF Level)_SWT db Receiver Blocking (Blocking Signal Level)_SWT db Receiver Blocking (Wanted RF Level)_SBT db Receiver Blocking (Blocking Signal Level)_SBT db Receiver Blocking (Blocking Signal Level)_without tester 1.68 db Kashima EMC Lab. Item Occupied Channel Bandwidth RF output power, conducted Conducted emissions Measurement (below 6 GHz) Conducted emissions Measurement (6 GHz - 18 GHz) Temperature Supply voltages Time Uncertainty (+/-) 1.6 % 0.74 db 2.2 db 2.2 db 0.89 deg. C 0.42 % % Item Frequency range Uncertainty (+/-) Radiated emission (Measurement distance: 3 m) 30 MHz MHz 4.7 db 300 MHz - 1 GHz 3.6 db Receiver Blocking 1 GHz - 13 GHz 4.8 db 2.3 db

7 Page : 7 of Test Location , Megumigaoka, Hiratsuka-shi, Kanagawa-ken JAPAN Telephone: , Facsimile: JAB Accreditation No. RTL02610 Test site IC Registration Number Width x Depth x Height (m) Size of reference ground plane (m) / horizontal conducting plane No.1 Semi-anechoic chamber 2973D x 11.3 x x m No.2 Semi-anechoic chamber 2973D x 11.3 x x m No.3 Semi-anechoic chamber 2973D x 7.7 x x 7.7 5m No.4 Semi-anechoic chamber x 5.1 x x No.1 Shielded room x 4.1 x x No.2 Shielded room x 4.1 x x No.3 Shielded room x 4.7 x x No.4 Shielded room x 4.7 x x No.5 Shielded room x 6.4 x x No.6 Shielded room x 6.4 x x No.8 shielded room x 5.5 x x No.1 Measurement room x 4.1 x Maximum measurement distance Kashima EMC Lab Mushihata, Katori-shi, Chiba-ken, JAPAN Telephone: , Facsimile: JAB Accreditation No. : RTL02610 Test site IC Registration Number Width x Depth x Height (m) Size of reference ground plane (m) / horizontal conducting plane No.1 Open site 4659A x 5.5 x x m No.2 Open site 4659A x 4.4 x x m No.5 Open site 4659A x 7.1 x x m No.1 Shielded room 4659A x 4.5 x No.2 Shielded room 4659A x 2.7 x No.3 Shielded room x 3.6 x No.4 Shielded Room x 6.1 x No.5 Shielded Room 4659A x 3.1 x No.3 Fully Anechoic Chamber x 3.5 x No.6 Semi-anechoic Chamber 4659A x 5.5 x m No.10 Semi-anechoic Chamber 4659A x 9.9 x m No.11 Semi-anechoic Chamber 4659A x 6.5 x m No.1 Measurement room x 3.7 x No.2 Measurement room x 4.4 x No.3 Measurement room x 4.4 x Maximum measurement distance 3.6 Test data, Test instruments, and Test set up Refer to APPENDIX.

8 Page : 8 of 24 SECTION 4: Operation of E.U.T. during testing 4.1 Operating Mode(s) Mode Remarks* Bluetooth (BT) Low Energy (LE) 1 Mbps Maximum Packet Size, PRBS9 Bluetooth (BT) Low Energy (LE) 2 Mbps Maximum Packet Size, PRBS9 ANT 1 Mbps 1 Mbps Nordic Original 2 Mbps 2 Mbps *Power of the EUT was set by the software as follows; Power settings: +4 dbm 10_BLE_TEST_tool-BT5 (for BT LE mode) Radio_test_tool_ (for ANT and Nordic Original mode except receiver blocking test) Blocking_tool (for receiver blocking test) *This setting of software is the worst case. Any conditions under the normal use do not exceed the condition of setting. In addition, end users cannot change the settings of the output power of the product. *The details of Operating mode(s) Test Item Operating Mode Tested frequency RF output power, Power Spectral Density Transmitting (Tx) BT LE 1 Mbps Transmitting (Tx) BT LE 2 Mbps 2402 MHz 2440 MHz Occupied channel bandwidth, Transmitter unwanted emissions in the out-of-band domain Transmitting (Tx) ANT 1 Mbps Transmitting (Tx) Nordic Original 2 Mbps Transmitting (Tx) BT LE 1 Mbps Transmitting (Tx) BT LE 2 Mbps Transmitting (Tx) ANT 1 Mbps Transmitting (Tx) Nordic Original 2 Mbps 2480 MHz 2402 MHz 2441 MHz 2480 MHz 2402 MHz 2480 MHz Receiver blocking Communication, ANT 1 Mbps *1) 2402 MHz 2480 MHz *1) Test mode was selected according to the test report: M-R1. Extreme test condition Temperature -40 deg. C to +105 deg. C : operating temperature range of EUT Voltage Vnom: DC 3.0 V

9 Page : 9 of Configuration and peripherals Other than Receiver blocking test B D C A 4 3 AC 100 V / 50 Hz 1 2 GND DC 3 V * Cabling and setup(s) were taken into consideration and test data was taken under worse case conditions. Description of EUT and Support equipment No. Item Model number Serial number Manufacturer Remark A Bluetooth low energy / EYSLSN 81*1) TAIYO YUDEN EUT ANT Module 82*2) B Evaluation Board TE TAIYO YUDEN - C Laptop PC CF-T2 4CKSA46826 Panasonic - D AC Adaptor CF-AA1625A 1625AM406Z21913F Panasonic - *1) Used for BT LE 1 Mbps and BT LE 2 Mbps *2) Used for ANT 1 Mbps and Nordic Original 2 Mbps List of cables used No. Name Length (m) Shield Remark Cable Connector 1 USB Cable 1.8 Shielded Shielded - 2 DC Cable Unshielded Unshielded - 3 DC Cable 1.2 Unshielded Unshielded - 4 AC Cable 0.8 Unshielded Unshielded -

10 Page : 10 of 24 Receiver blocking test 5 6 F DC 3 V E A B C D DC 3 V AC 100 V / 50 Hz * Cabling and setup(s) were taken into consideration and test data was taken under worse case conditions. Description of EUT and Support equipment No. Item Model number Serial number Manufacturer Remark A Bluetooth low energy / EYSLSN Rx TAIYO YUDEN EUT ANT Module B Laptop PC CF-T2 4CKSA46826 Panasonic - C AC Adaptor CF-AA1625A 1625AM406Z21913F Panasonic - D Evaluation Board TE TAIYO YUDEN - E Bluetooth low energy / EYSLSN Tx TAIYO YUDEN - ANT Module F Evaluation Board TE TAIYO YUDEN - List of cables used No. Name Length (m) Shield Remark Cable Connector 1 USB Cable 1.8 Shielded Shielded - 2 DC Cable Unshielded Unshielded - 3 DC Cable 1.2 Unshielded Unshielded - 4 AC Cable 0.8 Unshielded Unshielded - 5 USB Cable Shielded Shielded - 6 DC Cable 0.5 Unshielded Unshielded -

11 Page : 11 of 24 SECTION 5: Antenna Terminal Conducted Tests Test Procedure The tests were made with below setting connected to the antenna port. Test Instrument used Remark RF Output Power Power Meter Normal and Extreme conditions Power Spectral Density Spectrum Analyzer Normal condition Occupied Channel Spectrum Analyzer Normal condition Bandwidth Transmitter unwanted emissions in the out-of band domain Spectrum Analyzer Receiver Blocking Spectrum Analyzer Normal condition Normal conditions - Detector mode: RMS - Trace: Max Hold - Band power was used on behalf of the time domain power function. - Filter mode: Gaussian Filter Since the data in this test report has enough margin The test results are rounded off to two decimals place, so some differences might be observed. The equipment and cables were not used for factor 0.0 db of the data sheets. Test data Test result : APPENDIX : Pass

12 Page : 12 of 24 APPENDIX 1: Test data RF Output Power Report No S Test place No.5 Shielded Room Date July 23, 2018 July 27, 2018 Temperature / Humidity 25 deg. C / 50 % RH 24 deg. C / 47 % RH Engineer Kazuya Noda Kazuhiro Ando Mode Tx BT LE 1 Mbps Receiver Category : 2 Test Condition Freq. P/M (AV) Cable Atten. Antenna Result Limit Margin Temp. Volt. Reading Loss Loss Gain [MHz] [dbm] [db] [db] [dbi] [dbm] [dbm] [db] nom nom min nom max nom Result = Reading + Cable Loss (including the cable(s) customer supplied) + Attenuator Loss + Antenna Gain BT LE 2 Mbps Receiver Category : 2 Test Condition Freq. P/M (AV) Cable Atten. Antenna Result Limit Margin Temp. Volt. Reading Loss Loss Gain [MHz] [dbm] [db] [db] [dbi] [dbm] [dbm] [db] nom nom min nom max nom Result = Reading + Cable Loss (including the cable(s) customer supplied) + Attenuator Loss + Antenna Gain

13 Page : 13 of 24 RF Output Power Report No S Test place No.5 Shielded Room Date July 23, 2018 July 27, 2018 Temperature / Humidity 25 deg. C / 50 % RH 24 deg. C / 47 % RH Engineer Kazuya Noda Kazuhiro Ando Mode Tx ANT 1 Mbps Receiver Category : 2 Test Condition Freq. P/M (AV) Cable Atten. Antenna Result Limit Margin Temp. Volt. Reading Loss Loss Gain [MHz] [dbm] [db] [db] [dbi] [dbm] [dbm] [db] nom nom min nom max nom Result = Reading + Cable Loss (including the cable(s) customer supplied) + Attenuator Loss + Antenna Gain Nordic Original 2 Mbps Receiver Category : 2 Test Condition Freq. P/M (AV) Cable Atten. Antenna Result Limit Margin Temp. Volt. Reading Loss Loss Gain [MHz] [dbm] [db] [db] [dbi] [dbm] [dbm] [db] nom nom min nom max nom Result = Reading + Cable Loss (including the cable(s) customer supplied) + Attenuator Loss + Antenna Gain

14 Page : 14 of 24 Power Spectral Density Report No S Test place No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx BT LE 1 Mbps Test Condition Ch S/A S/A RF Output Result Limit Margin Temp. Volt. Freq. Maximum Total Power Power Reading Reading [MHz] [dbm/mhz] [dbm] [dbm] [dbm/mhz] [dbm/mhz] [db] nom nom Result [dbm/mhz] = S/A Maximum Reading [dbm/mhz] - S/A Total Power Reading [dbm] (*1) + RF Output Power [dbm] (*2) (*1) Integrated value of 2400 MHz to MHz (*2) Refer to RF Output Power BT LE 2 Mbps Test Condition Ch S/A S/A RF Output Result Limit Margin Temp. Volt. Freq. Maximum Total Power Power Reading Reading [MHz] [dbm/mhz] [dbm] [dbm] [dbm/mhz] [dbm/mhz] [db] nom nom Result [dbm/mhz] = S/A Maximum Reading [dbm/mhz] - S/A Total Power Reading [dbm] (*1) + RF Output Power [dbm] (*2) (*1) Integrated value of 2400 MHz to MHz (*2) Refer to RF Output Power ANT 1 Mbps Test Condition Ch S/A S/A RF Output Result Limit Margin Temp. Volt. Freq. Maximum Total Power Power Reading Reading [MHz] [dbm/mhz] [dbm] [dbm] [dbm/mhz] [dbm/mhz] [db] nom nom Result [dbm/mhz] = S/A Maximum Reading [dbm/mhz] - S/A Total Power Reading [dbm] (*1) + RF Output Power [dbm] (*2) (*1) Integrated value of 2400 MHz to MHz (*2) Refer to RF Output Power Nordic Original 2 Mbps Test Condition Ch S/A S/A RF Output Result Limit Margin Temp. Volt. Freq. Maximum Total Power Power Reading Reading [MHz] [dbm/mhz] [dbm] [dbm] [dbm/mhz] [dbm/mhz] [db] nom nom Result [dbm/mhz] = S/A Maximum Reading [dbm/mhz] - S/A Total Power Reading [dbm] (*1) + RF Output Power [dbm] (*2) (*1) Integrated value of 2400 MHz to MHz (*2) Refer to RF Output Power

15 Page : 15 of 24 Occupied Channel Bandwidth Report No S Test place No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx BT LE 1 Mbps Frequency Bandwidth Result Limit [MHz] [MHz] [MHz] [MHz] > < Tx 2402 MHz Tx 2480 MHz

16 Page : 16 of 24 Occupied Channel Bandwidth Report No S Test place No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx BT LE 2 Mbps Frequency Bandwidth Result Limit [MHz] [MHz] [MHz] [MHz] > < Tx 2402MHz Tx 2480MHz

17 Page : 17 of 24 Occupied Channel Bandwidth Report No S Test place No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx ANT 1 Mbps Frequency Bandwidth Result Limit [MHz] [MHz] [MHz] [MHz] > < Tx 2402MHz Tx 2480MHz

18 Page : 18 of 24 Occupied Channel Bandwidth Report No S Test place No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx Nordic Original 2 Mbps Frequency Bandwidth Result Limit [MHz] [MHz] [MHz] [MHz] > < Tx 2402 MHz Tx 2480 MHz

19 Page : 19 of 24 Transmitter unwanted emissions in the out-of-band domain Report No S Test place No.5 Shielded Room Date July 23, 2018 Temperature / Humidity 25 deg. C / 50 % RH Engineer Kazuya Noda Mode Tx BT LE 1 Mbps Frequency S/A (AV) Cable Atten. Antenna Result Limit Margin Remarks Reading Loss Loss Gain [MHz] [dbm/mhz] [db] [db] [dbi] [dbm/mhz] [dbm/mhz] [db] Lowest ch 2400 MHz - 2 BW Lowest ch 2400 MHz - BW Highest ch MHz + BW Highest ch MHz + 2 BW BT LE 2 Mbps Frequency S/A (AV) Cable Atten. Antenna Result Limit Margin Remarks Reading Loss Loss Gain [MHz] [dbm/mhz] [db] [db] [dbi] [dbm/mhz] [dbm/mhz] [db] Lowest ch 2400 MHz - 2 BW Lowest ch 2400 MHz - BW Highest ch MHz + BW Highest ch MHz + 2 BW ANT 1 Mbps Frequency S/A (AV) Cable Atten. Antenna Result Limit Margin Remarks Reading Loss Loss Gain [MHz] [dbm/mhz] [db] [db] [dbi] [dbm/mhz] [dbm/mhz] [db] Lowest ch 2400 MHz - 2 BW Lowest ch 2400 MHz - BW Highest ch MHz + BW Highest ch MHz + 2 BW Nordic Original 2 Mbps Frequency S/A (AV) Cable Atten. Antenna Result Limit Margin Remarks Reading Loss Loss Gain [MHz] [dbm/mhz] [db] [db] [dbi] [dbm/mhz] [dbm/mhz] [db] Lowest ch 2400 MHz - 2 BW Lowest ch 2400 MHz - BW Highest ch MHz + BW Highest ch MHz + 2 BW Result = Reading + Cable Loss (including the cable(s) customer supplied) + Attenuator Loss + Antenna Gain *Above test result was maximum value on each 1 BW.

20 Page : 20 of 24 Receiver Blocking Report No S Test place No.5 Shielded Room Date July 25, 2018 Temperature / Humidity 26 deg. C / 52 % RH Engineer Shiro Kobayashi Mode Communication, ANT 1 Mbps Measured Wanted signal mean Receiver Sensitivity power from (corrected by the actual antenna assembly companion device gain) (dbm) Lowest Channel Highest Channel Pmin Pmin + 6 db Receiver Category 2 equipment Operating Channel Lowest Channel Highest Channel Wanted signal mean Blocking signal Result power from Blocking signal power frequency PER companion device (dbm) *1) (MHz) (%) (dbm) P min + 6 db P min + 6 db P min + 6 db P min + 6 db Limit PER (%) *Pmin is the minimum level of wanted signal (in dbm) required to meet the minimum performance criterion a PER less than or equal to 10 % in the absence of any blocking signal. *The test was performed Blocking signal power levels corrected by the actual antenna assembly gain. *1) Blocking signal power was adjusted by assumed antenna gain 0.0 dbi since it was more severe condition.

21 Page : 21 of 24 Receiver Blocking dconducted METHODS SYSTEM BLOCK DIAGRAM of Receiver Blocking Competitor PC Step Attenuator Power Splitters/ Combiners EUT Signal Generator

22 Page : 22 of 24 APPENDIX 2: Test instruments Test Instruments Control No. Instrument Manufacturer Model No Serial No Test Item Calibration Date * Interval(month) KSA-08 Spectrum Analyzer Agilent E4446A MY RB 2017/10/10 * 12 SCC-G14 Coaxial Cable Suhner SUCOFLEX /2 AT 2018/03/19 * 12 SAT10-14 Attenuator Weinschel Corp. 54A AT 2018/04/20 * 12 SOS-09 Humidity Indicator A&D AD AT,RB 2017/12/21 * 12 KTS-07 Digital Tester SANWA PC AT,RB 2017/10/11 * 12 SPM-08 Power Meter DARE!! Instruments RPR3006W 15I00041SNO73 AT 2017/08/21 * 12 SSG-01 Signal Generator Agilent E4438C MY RB 2018/04/19 * 12 SCC-G34 Coaxial Cable Junkosha MWX KM SKMS/B SCC-G35 Coaxial Cable Junkosha MWX KM SKMS/B SCC-G36 Coaxial Cable Junkosha MWX KM SKMS/B SCC-G37 Coaxial Cable Junkosha MWX KM SKMS/B SPSC-02 Power Splitters/Combiners 1612Q032 RB 2018/01/25 * Q033 RB 2018/01/25 * Q034 RB 2018/01/25 * Q035 RB 2018/01/25 * 12 Mini-Circuits ZFSC-2-10G+ - RB 2018/04/20 * 12 SSAT-01 Step Attenuator KEYSIGHT 8494B MY RB 2018/02/07 * 12 SSAT-02 Step Attenuator KEYSIGHT 8496B MY RB 2018/02/07 * 12 CCH-04 Temperature and Humidity Chamber ESPEC PL-1J AT 2018/07/09 * 12 CPM-16 Peak Power Analyzer AGILENT 8990B MY AT 2018/06/20 * 12 CPSO-24 Power Sensor AGILENT N1923A MY AT 2018/06/20 * 12 CAT dB Fixed Atten WEINSCHEL 54A AT 2018/05/21 * 12 CCC-G13 Microwave Cable Huder + Suhner SF102/SKm/SKm/10 00mm AT 2018/07/25 * 12 CTS-18 Digital Multimeter Fluke Corporation AT 2017/09/11 * 12 COS-11 Temperature Humidity & Atmospheric Logger T&D TR-73U F806046B AT 2018/05/28 * 12 The expiration date of the calibration is the end of the expired month. All equipment is calibrated with valid calibrations. Each measurement data is traceable to the national or international standards. As for some calibrations performed after the tested dates, those test equipment have been controlled by means of an unbroken chains of calibrations. Test item: AT: Antenna Terminal Conducted test RB: Reciever blocking test

23 Page : 23 of 24 APPENDIX 3: Photographs of test setup Antenna terminal conducted tests other than Receiver Blocking ()

24 Page : 24 of 24 Receiver Blocking End of Report