REVISION HISTORY. Original Test Report No.: S-D. Revision Test report No. Date Page revised Contents -

Transcription

1

2 REVISION HISTORY Original Test Report No.: S-D Test report No. : S-D Page : 2 of 17 Revision Test report No. Date Page revised Contents S-D July 26, (Original)

3 Page : 3 of 17 CONTENTS PAGE SECTION 1: Customer information... 4 SECTION 2: Equipment under test (E.U.T.)... 4 SECTION 3: Test specification, procedures and results... 5 SECTION 4: Operation of E.U.T. during testing... 7 SECTION 5: Conducted emission... 9 SECTION 6: Radiated emission CONTENTS OF APPENDIXES 11 APPENDIX 1: Photographs of test setup APPENDIX 2: Data of EMI test APPENDIX 3: Test instruments... 17

4 Page : 4 of 17 SECTION 1: Customer information Company Name : JAI Corporation Address : Sakae-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, JAPAN Telephone Number : Facsimile Number : Contact Person : Yoshinobu Ihara SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of equipment : CCD Camera Model number : SP-20000C-CXP2 Serial number : Rating : DC 24V Country of mass-production: Japan Condition of EUT : Production prototype (Not for Sale: This sample is equivalent to mass-produced items.) Receipt date of sample : July 6, 2013 Modification of EUT : No modification by the test lab. 2.2 Product description Model number: SP-20000C-CXP2 (referred to as the EUT in this report) is a CCD Camera. The clock frequencies used in the EUT: 3.125GHz

5 Page : 5 of 17 SECTION 3: Test specification, procedures and results 3.1 Test specification Test Specification : FCC Part15 Subpart B: 2013, final revised on June 11, 2013 and effective July 11, 2013 Title : FCC 47CFR Part15 Radio Frequency Device Subpart B Unintentional Radiators * The revision on June 11, 2013 does not affect the test specification applied to the EUT. 3.2 Procedures and results Item Test procedure Limits Deviation Worst margin Result Conducted emission ANSI C63.4: AC power line conducted emission measurements Class B N/A *1) 5.5 db Freq.: MHz Detector: Average Phase: N Complied Radiated emission ANSI C63.4: Radiated emission measurements Class B N/A *2) 2.0 db Freq.: MHz Detector: Quasi-Peak Polarization: Horizontal Complied *1) The calibration of test receiver contains CISPR requirements. *2) Measurements were limited up to 16 GHz since the highest frequency of internal source of the EUT is GHz. Note 1: UL Japan s EMI work procedure No. 13-EM-W Addition, deviation, exclusion to standards No addition, deviation nor exclusion has been made from standards. 3.4 Confirmation hereby confirms the E.U.T., in the configuration tested, complies with the specifications FCC Part15 Subpart B: 2013 Class B.

6 Page : 6 of Uncertainty The following uncertainties have been calculated to provide a confidence level of 95% using a coverage factor k=2. Item Frequency range No.1 SAC *1 /SR *2 (±) No.2 SAC/SR (±) No.3 SAC/SR (±) Conducted emission (AC Mains) LISN Radiated emission (Measurement distance: 3m) *1: SAC=Semi-Anechoic Chamber *2: SR= Shielded Room is applied besides radiated emission 150kHz-30MHz 3.6 db 3.6 db 3.5 db 1GHz-18GHz 4.8 db 4.8 db 4.9 db 30MHz-300MHz 4.9 db 5.1 db 4.9 db 300MHz-1GHz 5.0 db 5.2 db 4.9 db Conducted emission (AC power line) test The data listed in this test report has enough margin, more than site margin. Radiated emission test The data listed in this report meets the limits unless the uncertainty is taken into consideration. 3.6 Test location Megumigaoka Hiratsuka-shi Kanagawa-ken JAPAN Telephone number : Facsimile number : JAB Accreditation No. : RTL02610 FCC Registration No. IC Registration No. Width x Depth x Height (m) Size of reference ground plane (m) / horizontal conducting plane No.1 semi-anechoic chamber D x 11.3 x x m No.2 semi-anechoic chamber D x 11.3 x x m No.3 semi-anechoic chamber D x 7.7 x x 7.7 5m No.4 semi-anechoic chamber x 5.1 x x No.1 shielded room x 4.1 x x No.2 shielded room x 4.1 x x No.3 shielded room x 4.7 x x No.4 shielded room x 4.7 x x No.5 shielded room x 6.4 x x No.6 shielded room x 6.4 x x Test setup, data of EMI test and test instruments Refer to Appendix 1 to 3. Maximum measurement distance

7 Page : 7 of 17 SECTION 4: Operation of E.U.T. during testing 4.1 Operating mode The EUT exercise program used during testing was designed to exercise the various system components in a manner similar to typical use. Test sequence is used : Normal Justification: The system was configured in typical fashion (as a customer would normally use it) for testing. 4.2 Configuration and peripherals B A: EUT 1 I C 9 F G 6 7 D E 5 AC100V/50Hz H 3 4 AC120V/60Hz *Cabling and setup were taken into consideration and test data was taken under worse case conditions.

8 Page : 8 of 17 Description of EUT and support equipment No. Item Model number Serial number Manufacturer Remark A CCD Camera SP-20000C-CXP JAI Corporation EUT B Lens AF NIKKOR 35-F1.2 - NIKON - C Conversion Box - - JAI Corporation - D CoaxPress I/F APX (e3A) AVAL DATA - E Personal Computer T3500 7M1DTBX DELL - F Keyboard SK W213F DELL - G Mouse M-UAV-DEL8 K251D DELL - H LCD Monitor U2311Hb CN-01F20K DELL - 13A-1M8L I Printer BJF600 ESF50801 Canon - List of cables used No. Name Length (m) Shield Shield Remark (Cable) (Connector) 1 DC Power 10.0 Shielded Shielded For CCD Camera 2 BELDEN BNC/DIN-1855A Shielded Shielded - BNC-DIN1.0/2.3 3 AC Power 2.0 Unshielded Unshielded For Personal Computer 4 AC Power 3.0 Unshielded Unshielded For LCD Monitor 5 LCD DVI 1.5 Shielded Shielded - 6 Keyboard 1.4 Shielded Shielded - 7 Mouse 1.4 Shielded Shielded - 8 Printer 1.8 Shielded Shielded - 9 AC Power 2.0 Unshielded Unshielded For Printer 10 BELDEN BNC/DIN-1855A-10 BNC-DIN1.0/ Shielded Shielded -

9 Page : 9 of 17 SECTION 5: Conducted emission 5.1 Operating environment The test was carried out in No.1 Shielded Room. Temperature and humidity : See test data 5.2 Test configuration EUT was placed on a platform of nominal size, 1.0m by 2.0m, raised 0.8m above the conducting ground plane. The rear of tabletop was located 40cm to the vertical conducting plane. The rear of EUT, including peripherals was aligned and was flushed with rear of tabletop. All other surfaces of tabletop were at least 80cm from any other grounded conducting surface. EUT was located 80cm from LISN (Line Impedance Stabilization Network) and excess AC cable was bundled in center. I/O cables that were connected to the peripherals were bundled in center. They were folded back and for the forming a bundle 30cm to 40cm long and were hanged at a 40cm height to the ground plane. Each EUT current-carrying power lead, except the ground (safety) lead, was individually connected through a LISN to the input power source. All unused 50ohm connectors of the LISN were resistively terminated in 50ohm when not connected to the measuring equipment. Photographs of the set up are shown in Appendix Test conditions Frequency range : MHz EUT position : Table top EUT operation mode : See clause Test procedure The AC power line continuous disturbance voltage had been measured with the EUT within a screened room. The EUT was connected to a Line Impedance Stabilization Network (LISN). An overview sweep with peak detection had been performed. The measurements had been performed with a quasi-peak detector and if required, with a CISPR average detector (CAV). The conducted disturbance measurements were made with the following detector function of the test receiver. Detector Type : QP / CAV IF Bandwidth : 9kHz / 9kHz 5.5 Results Summary of the test results : Pass

10 Page : 10 of 17 SECTION 6: Radiated emission 6.1 Operating environment The test was carried out in No.1 Semi-Anechoic Chamber. Temperature and humidity : See test data 6.2 Test configuration For measurement below 1GHz, EUT was placed on a platform of nominal size, 1.0m by 1.5m, raised 0.8m above the conducting ground plane. The table is made of Styrofoam and covered with polyvinyl chloride. That has very low permittivity. For measurement above 1GHz, EUT was placed on a polyurethane platform of nominal size, and 0.5m by 0.5m, raised 0.8m above the conducting ground plane. The rear of EUT was aligned and flushed with rear of tabletop. Photographs of the set up are shown in Appendix Test conditions Frequency range : 30MHz - 16GHz Test distance : 3m EUT position : Table top EUT operation : See clause Test procedure The radiated electric field strength intensity has been measured on the semi anechoic chamber with a ground plane at a distance of 3m (refer to Figure 1). Measurements were performed with a quasi-peak, peak and average detector. The measuring antenna height was varied between 1 to 4m and EUT was rotated a full revolution in order to obtain the maximum value of the electric field intensity. The measurements were performed for both vertical and horizontal antenna polarization. Frequency : 30MHz - 1GHz 1-16GHz Instrument used : Test Receiver Spectrum Analyzer Detector Type : Quasi-Peak Peak Average* IF Bandwidth : 120kHz RBW:1MHz, VBW:3MHz RBW:1MHz, VBW:10Hz *When using spectrum analyzer, the test was performed with adjusting span to zero by using peak hold. No.1 Semi-Anechoic Chamber (Antenna angle) Biconical Antenna Radiated Emission (Below 1GHz) No.1 Semi-Anechoic Chamber (Antenna angle) : Absorbers(600mm x 600mm) 45 deg. Radiated Emission (Above 1GHz) 45 deg. TurnTable TurnTable 17 deg. Measuring Distance 10m : RED LINE 3m : GREEN LINE 0 deg. -17 deg. -45 deg. 2m / 1t 5m / 5t Measuring Distance 10m : RED LINE 3m : GREEN LINE 0 deg. 3m 2m / 1t 5m / 5t 6.5 Results Logperiodic Antenna Figure 1. Antenna angle Measuring Receiver Horn Antenna Summary of the test results : Pass

11 Page : 11 of 17 CONTENTS OF APPENDIXES APPENDIX 1: Photographs of test setup Conducted emission Radiated emission APPENDIX 2: Data of EMI test Conducted emission Radiated emission APPENDIX 3: Test instruments EMI test instruments

12 Page : 12 of 17 APPENDIX 1: Photographs of test setup Conducted emission

13 Page : 13 of 17 Radiated emission Below 1GHz Above 1GHz AE

14 Test Report No : S-D DATA OF CONDUCTED EMISSION TEST No.1 Shielded Room Date : 2013/07/06 Company : JAI Corporation Mode : Normal Kind of EUT : CCD Camera Order No. : S Model No. : SP-20000C-CXP2 Power : PC:AC120V/60Hz, EUT:DC24V Serial No. : β Temp./Humi. : 23deg.C / 71%RH Remarks : - Limit1 : FCC 15B(15.107) ClassB QP Limit2 : FCC 15B(15.107) ClassB AV Engineer : Tomochika Sato Limit1(QP) Limit2(AV) RFI Voltage [dbuv] N(PK) N(QP/AV) L1(PK) L1(QP/AV) Frequency [MHz] 30 No. Reading Results Limit Margin Freq. C.Fac <QP> <AV> <QP> <AV> <QP> <AV> <QP> <AV> Phase Comment [MHz] [dbuv] [dbuv] [db] [dbuv] [dbuv] [dbuv] [dbuv] [db] [db] N N N N N N L L L L L L1 Calculation:Result[dBuV]=Reading[dBuV]+C.Fac(LISN+Cable+ATT)[dB] LISN:SLS of 17

15 Test Report No : S-D DATA OF RADIATED EMISSION TEST No.1 Semi-Anechoic Chamber Date : 2013/07/06 Company : JAI Corporation Mode : Normal Kind of EUT : CCD Camera Order No. : S Model No. : SP-20000C-CXP2 Power : DC24V Serial No. : β Temp./Humi. : 24deg.C / 77%RH Remarks : - Limit1 : FCC 15B Class B (3m) Engineer : Tomochika Sato Field Strength [dbuv/m] Frequency [MHz] 1000 Limit1(QP) Hori.(QP) Vert.(QP) No. Reading Result Limit Margin Freq. <QP> Ant.Fac Loss Gain S.Fac Pola. Height Angle <QP> <QP> <QP> Ant. Type [MHz] [dbuv] [db/m] [db] [db] [db] [dbuv/m] [dbuv/m] [db] [H/V] [cm] [deg] Hori LP Hori LP Vert BC Vert BC Vert BC Vert BC Vert LP Comment Calculation:Result[dBuV/m]=Reading[dBuV]+Ant.Fac[dB/m]+Loss(Cable+ATT)[dB]-Gain(AMP)[dB]+S.Fac(ΔAF) [db] Ant.Type=BC:Biconical Antenna, LP:Logperiodic Antenna, SHA**:Horn Antenna 15 of 17

16 Test Report No : S-D DATA OF RADIATED EMISSION TEST No.1 Semi-Anechoic Chamber Date : 2013/07/06 Company : JAI Corporation Mode : Normal Kind of EUT : CCD Camera Order No. : S Model No. : SP-20000C-CXP2 Power : DC24V Serial No. : β Temp./Humi. : 24deg.C / 77%RH Remarks : - Limit1 : FCC 15B Class B (3m) AV Limit2 : FCC 15B Class B (3m) Peak Engineer : Tomochika Sato Field Strength [dbuv/m] Frequency [GHz] Limit1(AV) Limit2(PK) Hori.(AV/PK) Vert.(AV/PK) No. Reading Result Limit Margin Freq. Ant.Fac Loss Gain Pola. Height Angle <AV> <PK> <AV> <PK> <AV> <PK> <AV> <PK> Ant. Type [MHz] [dbuv] [dbuv] [db/m] [db] [db] [dbuv/m] [dbuv/m] [dbuv/m] [dbuv/m] [db] [db] [H/V] [cm] [deg] Hori SHA Hori SHA Hori SHA Hori SHA Hori SHA Vert SHA01 Comment Calculation:Result[dBuV/m]=Reading[dBuV]+Ant.Fac[dB/m]+Loss(Cable)[dB]-Gain(AMP)[dB] Ant.Type=BC:Biconical Antenna, LP:Logperiodic Antenna, SHA**:Horn Antenna 16 of 17

17 Test Report No : S APPENDIX 3 Test Instruments EMI test equipment Test Report No : S-D Control No. Instrument Manufacturer Model No Serial No Test Item Calibration Date * Interval(month) SAF-01 Pre Amplifier SONOMA 310N RE 2013/02/12 * 12 SAT6-05 Attenuator JFW 50HF-006N - RE 2013/02/12 * 12 SAT3-04 Attenuator JFW 50HF-003N - RE 2013/02/12 * 12 SBA-01 Biconical Antenna Schwarzbeck BBA RE 2012/10/08 * 12 SCC-A1/A3/A5 Coaxial Cable&RF Fujikura/Fujikura/Suhne 8D2W/12DSFA/14 -/ (RF RE 2013/04/04 * 12 /A7/A8/A13/S Selector r/suhner/suhner/suhn 1PE/141PE/141PE Selector) RSE-01 er/toyo /141PE/NS4906 SCC-A2/A4/A6 Coaxial Cable&RF Fujikura/Fujikura/Suhne 8D2W/12DSFA/14 -/ (RF RE 2013/04/04 * 12 /A7/A8/A13/S Selector r/suhner/suhner/suhn 1PE/141PE/141PE Selector) RSE-01 er/toyo /141PE/NS4906 SLA-01 Logperiodic Antenna Schwarzbeck UHALP9108A UHALP 9108-A RE 2012/11/18 * SOS-01 Humidity Indicator A&D AD RE 2013/02/27 * 12 STR-01 Test Receiver Rohde & Schwarz ESU RE, CE 2012/10/04 * 12 SJM-08 Measure PROMART SEN RE, CE - SAEC-01(NSA) Semi-Anechoic Chamber TDK SAEC-01(NSA) 1 RE 2012/09/11 * 12 COTS-SEMI-1 EMI Software TSJ TEPTO-DV(RE,CE, - RFI,MF) RE, CE - SAF-04 Pre Amplifier TOYO Corporation TPA RE 2013/03/19 * 12 SCC-G01 Coaxial Cable Suhner SUCOFLEX 104A 46497/4A RE 2013/04/09 * 12 SCC-G21 Coaxial Cable Suhner SUCOFLEX /4 RE 2013/05/22 * 12 SHA-01 Horn Antenna Schwarzbeck BBHA9120D 9120D-725 RE 2012/08/20 * 12 SCC-A12/A13/ SRSE-01 Coaxial Cable&RF Selector Suhner/Suhner/TOYO RG223U/141PE/N S4906 -/ (RF Selector) CE 2013/04/04 * 12 SLS-01 LISN Rohde & Schwarz ENV CE 2013/02/22 * 12 SLS-02 LISN Rohde & Schwarz ENV CE(AE) 2013/02/21 * 12 SAT3-03 Attenuator JFW 50HF-003N - CE 2013/02/12 * 12 SOS-02 Humidity Indicator A&D AD CE 2013/03/07 * 12 STM-01 Terminator TME CT-01 BP - CE 2013/01/16 * 12 The expiration date of the calibration is the end of the expired month. As for some calibrations performed after the tested dates, those test equipment have been controlled by means of an unbroken chains of calibrations. All equipment is calibrated with valid calibrations. Each measurement data is traceable to the national or international standards. Test Item: CE: Conducted emission, RE: Radiated emission End of Report Page : 17 of 17