CE Radio Test Report

Transcription

1 Report No. : ER CE Radio Test Report APPLICANT EQUIPMENT BRAND NAME MODEL NAME MARKETING NAME : Texas Instruments Incorporated : CC2564 Bluetooth HCI Module : Texas Instruments : CC2564MODA : CC2564MODA Bluetooth Host Controller Interface (HCI) Module STANDARD : ETSI EN V2.1.1 ( ) TEST DATE(S) : Jun. 19, 2017 ~ Jun. 27, 2017 The measurement shown in this variant report is tested in accordance with the test procedures given in ETSI EN V2.1.1 ( ). The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Joseph Lin / Supervisor Approved by: Jones Tsai / Manager SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1st Rd.,Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan R.O.C. SPORTON INTERNATIONAL INC. Page Number : 1 of 34 TEL : Report Issued Date : Jun. 30, 2017

2 Report No. : ER TABLE OF CONTENTS REVISION HISTORY... 3 SUMMARY OF TEST RESULT GENERAL DESCRIPTION Applicant Manufacturer Product Feature of Equipment Under Test Modification of EUT Testing Facility Applied Standards Test Condition TEST CONFIGURATION OF EQUIPMENT UNDER TEST Descriptions of Test Mode Connection Diagram of Test System Supported Unit used in test configuration and system EUT Operation Test Setup TRANSMITTER PARAMETERS Maximum Transmit Power Maximum Equivalent Isotropically Radiated Power (E.I.R.P.) Spectral Density Occupied Channel Bandwidth Transmitter unwanted emissions in the out-of-band domain Transmitter spurious emissions RECEIVER PARAMETERS Receiver spurious emissions Receiver Blocking Test ADAPTIVITY TEST Adaptivity GEO-LOCATION CAPABILITY Geo-location LIST OF MEASURING EQUIPMENT UNCERTAINTY EVALUATION APPENDIX A. TEST RESULT OF CONDUCTED TEST ITEMS APPENDIX B. CONDUCTED SPURIOUS EMISSION PLOTS APPENDIX C. CABINET RADIATION PLOTS APPENDIX D. PHOTOGRAPHS OF RADIATED EMISSION TEST CONFIGURATION APPENDIX E. ORIGINAL REPORT SPORTON INTERNATIONAL INC. Page Number : 2 of 34 TEL : Report Issued Date : Jun. 30, 2017

3 Report No. : ER REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE ER Rev. 01 Initial issue of report Jun. 30, 2017 SPORTON INTERNATIONAL INC. Page Number : 3 of 34 TEL : Report Issued Date : Jun. 30, 2017

4 Report No. : ER SUMMARY OF TEST RESULT CLAUSE (EN ) TEST PARAMETER PASS/FAIL REMARK Transmitter Parameters Maximum Transmit Power PASS - Maximum Equivalent Isotropically Radiated Power (E.I.R.P.) Spectral Density PASS Only applicable for modulations other than FHSS Occupied Channel Bandwidth PASS - Frequency Hopping Requirements PASS Only applicable for FHSS Transmitter spurious emissions in OOB PASS - Transmitter spurious emissions PASS Under limit 5.98 db at MHz Receiver Parameters Receiver spurious emissions PASS Under limit 6.04 db at MHz Adaptive Test Item Adaptivity PASS Only applicable for adaptive equipment Output Power >10dBm Receiver Blocking PASS - Non-Adaptive Test Item Duty cycle, Tx-Sequence, Tx-gap Not Required Only applicable for non-adaptive equipment Medium Utilisation (MU) factor Not Required Output Power >10dBm Note:Bluetooth belongs to adaptive equipment and EIRP < 10dBm. SPORTON INTERNATIONAL INC. Page Number : 4 of 34 TEL : Report Issued Date : Jun. 30, 2017

5 Report No. : ER General Description 1.1 Applicant Texas Instruments Incorporated TI BLVD., Dallas Texas, Manufacturer Texas Instruments Incorporated TI BLVD., Dallas Texas, Product Feature of Equipment Under Test Specification of the Equipment under Test RF General Information Frequency Bluetooth Ch. Frequency Channel Power Range Data Rate Mode (MHz) Number Setting (MHz) BR V [79] 1 Mbps 0x EDR V [79] 2 Mbps 0x EDR V [79] 3 Mbps 0x LE V [40] 1 Mbps 0x14 Note 1: Bluetooth BR uses a GFSK modulation Note 2: Bluetooth EDR uses a combination of /4-DQPSK and 8DPSK. Note 3: Bluetooth LE (Low energy) uses GFSK modulation Antenna Details Antenna information Brand Antenna Type Model 2.4GHz ~2.5GHz Gain 1 Yageo Chip ANT3216A063R2400A 1.00 Remark: This is a variant report by changing antenna gain. All the test cases were performed on original report which can be referred to Sporton Report Number ER as appendix E Based on the original report, only Bluetooth LE case and Bluetooth BR Adaptivity item was verified. SPORTON INTERNATIONAL INC. Page Number : 5 of 34 TEL : Report Issued Date : Jun. 30, 2017

6 Report No. : ER Modification of EUT No modifications are made to the EUT during all test items. 1.5 Testing Facility Test Site Test Site Location Test Site No. SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1st Rd.,Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan R.O.C. TEL: FAX: Sporton Site No. : TH05-HY ; DFS02-HY ; 05CH02-HY Test Site Test Site Location Test Site No. SPORTON INTERNATIONAL INC. No.58, Aly. 75, Ln. 564, Wenhua 3rd Rd., Kwei-Shan District, Tao Yuan City, Taiwan R.O.C. TEL: FAX: Sporton Site No. : 03CH15-HY 1.6 Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of ETSI EN V2.1.1 ( ). Note: All test items were verified and recorded according to the standards and without any deviation during the test. 1.7 Test Condition Normal Voltage DC 3.6V Normal Temperature 25 Extreme Temperature -30 and 85 Note: The test temperature was between -30 C ~ 85 C by manufacturer request. SPORTON INTERNATIONAL INC. Page Number : 6 of 34 TEL : Report Issued Date : Jun. 30, 2017

7 Report No. : ER Test Configuration of Equipment under Test 2.1 Descriptions of Test Mode a. During testing, the interface cables and equipment positions were varied according to ETSI EN V2.1.1 ( ). b. The complete test system included EUT for RF test. c. Preliminary tests were checked in different data rate and recorded worse in the following tables: RF Tx Rx Test Modes Bluetooth LE GFSK Bluetooth LE CH00 (2402MHz) Bluetooth LE CH39 (2480MHz) Bluetooth LE CH39 (2480MHz) SPORTON INTERNATIONAL INC. Page Number : 7 of 34 TEL : Report Issued Date : Jun. 30, 2017

8 Report No. : ER Connection Diagram of Test System System Simulator AP router Notebook GPS Station BT Earphone Power Source EUT Notebook Cradle Earphone ipod WLAN AP Monitor This example is connection diagram of EUT test configurations.. For detail, please refer to test mode configuration and setup photographs for each test item. 2.3 Supported Unit used in test configuration and system Item Equipment Trade Name Model Name FCC ID Data Cable Power Cord 1. Notebook DELL P20G FCC DoC/ Contains FCC ID: N/A QDS-BRCM Notebook Lenovo IdeaPad(8007) FCC DoC N/A AC I/P: Unshielded, 1.2 m DC O/P: Shielded, 1.8 m AC I/P: Unshielded, 1.2 m DC O/P: Shielded, 1.8 m 2.4 EUT Operation Test Setup For Bluetooth 4.1 LE test items, an engineering test program (HCITester) was provided and enabled to make EUT continuous transmitting and receiving signals SPORTON INTERNATIONAL INC. Page Number : 8 of 34 TEL : Report Issued Date : Jun. 30, 2017

9 Report No. : ER Transmitter Parameters 3.1 Maximum Transmit Power Limit of Effective Isotropic Radiated Power SUBCLAUSE and TEST CONDITION LIMIT Normal and Extreme Temperature Conditions 20dBm (e.i.r.p) Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedure 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. Placing the EUT in thermal chamber. 3. The EUT is connected to external power supply. 4. Setting thermal chamber temperature and power supply voltage at suitable values. 5. The EIRP = A+G+Y, where A is the power measured, G is the assembly gain of the individual antenna of the EUT in dbi and Y is the additional beamforming gain of the EUT in db if applicable, here, Y=0. 6. The measurement duration is at least 1 second to ensure a minimum number of bursts (at least 10) are captured Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 9 of 34 TEL : Report Issued Date : Jun. 30, 2017

10 Report No. : ER Maximum Equivalent Isotropically Radiated Power (E.I.R.P.) Spectral Density Limit of Maximum Power Spectral Density TEST CONDITION Normal and Extreme Temperature Conditions SUBCLAUSE LIMIT 10dBm / MHz Remark: Maximum spectral power density is not applicable to FHSS system device Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedure 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. These measurements shall only be performed at normal test conditions. 3. The measurement shall be repeated for the equipment being configured to operate at the lowest, the middle, and the highest frequency of the stated frequency range. 4. The test procedure shall be as follows: Step 1: Connect the EUT to the spectrum analyzer and use the following settings: Start Frequency 2400MHz Stop Frequency MHz Resolution BW 10kHz Video BW 30kHz Sweep Points 8350 Detector RMS Trace Mode Max Hold Sweep time 10 sec SPORTON INTERNATIONAL INC. Page Number : 10 of 34 TEL : Report Issued Date : Jun. 30, 2017

11 Report No. : ER Step 2: Add up the values for amplitude (power) for all the samples in the file. Step 3: Normalize the individual values for amplitude so that the sum is equal to the RF Output Power (e.i.r.p.) measured. Step 4: Starting from the first sample in the file (lowest frequency), add up the power of the following samples representing a 1 MHz segment and record the results for power and position (i.e. sample #1 to #100). This is the Power Spectral Density (e.i.r.p.) for the first 1 MHz segment which shall be recorded. Step 5: Shift the start point of the samples added up in step 4 by 1 sample and repeat the procedure in step 4 (i.e. sample #2 to #101). Step 6: Repeat step 5 until the end of the data set and record the radiated Power Spectral Density values for each of the 1 MHz segments. From all the recorded results, the highest value is the maximum Power Spectral Density for the EUT. This value shall be recorded in the test report Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 11 of 34 TEL : Report Issued Date : Jun. 30, 2017

12 Report No. : ER Occupied Channel Bandwidth Limit of Occupied Channel Bandwidth Occupied Channel Bandwidth fall completely within 2.4 GHz GHz Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedure 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. The measurement shall be performed only on the lowest and the highest frequency within the stated frequency range. 3. The test procedure shall be as follows: Step 1: Connect the EUT to the spectrum analyzer and use the following settings: Center Frequency Channel under test Resolution BW 1 % of the span Video BW 3 RBW Frequency Span 2 Nominal Channel Bandwidth Detector RMS Trace Mode Max Hold Sweep Time 1 s Step 2: Wait until the trace is completed. Find the peak value of the trace and place the analyzer marker on this peak. Step 3: Use the 99 % bandwidth function of the spectrum analyzer to measure the Occupied Channel Bandwidth of the EUT. SPORTON INTERNATIONAL INC. Page Number : 12 of 34 TEL : Report Issued Date : Jun. 30, 2017

13 Report No. : ER Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 13 of 34 TEL : Report Issued Date : Jun. 30, 2017

14 Report No. : ER Transmitter unwanted emissions in the out-of-band domain Transmitter unwanted emissions in the out-of-band domain limit out-of-band domain limit Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. These measurements shall only be performed at normal test conditions. 3. For conducted measurements on devices with multiple transmit chains using the results for each of the transmit chains for the corresponding 1 MHz segments shall be added and compared with the transmit mask limit Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 14 of 34 TEL : Report Issued Date : Jun. 30, 2017

15 Report No. : ER Bluetooth 4.1 LE OOB worse case SPORTON INTERNATIONAL INC. Page Number : 15 of 34 TEL : Report Issued Date : Jun. 30, 2017

16 Report No. : ER Transmitter spurious emissions Limit of Transmitter spurious emissions In case of equipment with antenna connectors, these limits apply to emissions at the antenna port (conducted). For emissions radiated by the cabinet or emissions radiated by integral antenna equipment (without antenna connectors), these limits are e.r.p. for emissions up to 1 GHz and as e.i.r.p. for emissions above 1 GHz. SUBCLAUSE and FREQUENCY RANGE MAXIMUM POWER BANDWIDTH 30 MHz to 47 MHz -36 dbm 100 khz 47 MHz to 74 MHz -54 dbm 100 khz 74 MHz to 87,5 MHz -36 dbm 100 khz 87,5 MHz to 118 MHz -54 dbm 100 khz 118 MHz to 174 MHz -36 dbm 100 khz 174 MHz to 230 MHz -54 dbm 100 khz 230 MHz to 470 MHz -36 dbm 100 khz 470 MHz to 862 MHz -54 dbm 100 khz 862 MHz to 1 GHz -36 dbm 100 khz 1 GHz to 12,75 GHz -30 dbm 1 MHz Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. The EUT was placed on a turntable with 1.5m height. 3. The test distance between the receiving antenna and the EUT is 3meter below 1GHz frequency range, and 3 meter which is in far field test condition for measured frequency above 1GHz, while the receiving (test) antenna is kept at 1.5 meter height. 4. Set EUT in continuous transmitting with maximum output power. 5. The table was rotated from 0 to 360 degree to search the highest radiated emission. 6. Repeating step 3 and 4 for each polarization and channel to find the worst emission level. 7. The results obtained are compared to the limits in order to prove compliance with the requirement. SPORTON INTERNATIONAL INC. Page Number : 16 of 34 TEL : Report Issued Date : Jun. 30, 2017

17 Report No. : ER Test Setup <Conducted Method> <Below 1GHz> <Above 1GHz> Test Results Please refer to Appendix B and C. SPORTON INTERNATIONAL INC. Page Number : 17 of 34 TEL : Report Issued Date : Jun. 30, 2017

18 Report No. : ER Receiver Parameters 4.1 Receiver spurious emissions Limit of Receiver spurious emissions In case of equipment with antenna connectors, these limits apply to emissions at the antenna port (conducted). For emissions radiated by the cabinet or emissions radiated by integral antenna equipment (without antenna connectors), these limits are e.r.p. for emissions up to 1 GHz and as e.i.r.p. for emissions above 1 GHz. SUBCLAUSE and FREQUENCY RANGE MAXIMUM POWER BANDWIDTH 30 MHz to 1 GHz -57 dbm 100kHz 1 GHz to 12,75 GHz -47 dbm 1MHz Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. The EUT was placed on a turntable with 1.5m height. 3. The test distance between the receiving antenna and the EUT is 3meter below 1GHz frequency range, and 3 meter which is in far field test condition for measured frequency above 1GHz, while the receiving (test) antenna is kept at 1.5 meter height. 4. Set EUT in receiving mode. 5. The table was rotated from 0 to 360 degree to search the highest radiated emission. 6. Repeating step 3 and 4 for each polarization and channel to find the worst emission level. 7. The results obtained are compared to the limits in order to prove compliance with the requirement. SPORTON INTERNATIONAL INC. Page Number : 18 of 34 TEL : Report Issued Date : Jun. 30, 2017

19 Report No. : ER Test Setup <Conducted Method> <Below 1GHz> <Above 1GHz> Test Results Please refer to Appendix B and C. SPORTON INTERNATIONAL INC. Page Number : 19 of 34 TEL : Report Issued Date : Jun. 30, 2017

20 Report No. : ER Receiver Blocking Test Limit of Receiver Blocking Test The minimum performance criterion shall be a PER less than or equal to 10%. Receiver category 1 1. Adaptive equipment with maximum RF output power > 10dBm e.i.r.p. (EX: WiFi) Receiver category 2 1. Non-adaptive equipment with MU 1% ~ 10% 2. Adaptive equipment with Maximum RF output power < 10dBm e.i.r.p. (EX: Bluetooth) SPORTON INTERNATIONAL INC. Page Number : 20 of 34 TEL : Report Issued Date : Jun. 30, 2017

21 Report No. : ER SPORTON INTERNATIONAL INC. Page Number : 21 of 34 TEL : Report Issued Date : Jun. 30, 2017

22 Report No. : ER Receiver category 3 1. Non-adaptive equipment with MU < 1% 2. Adaptive equipment with Maximum RF output power < 0dBm e.i.r.p Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. For systems using multiple receive chains only one chain (antenna port) need to be tested. All other receiver inputs shall be terminated Test Setup SPORTON INTERNATIONAL INC. Page Number : 22 of 34 TEL : Report Issued Date : Jun. 30, 2017

23 Report No. : ER Test Results of Receiver Blocking Pmin = CMW500 burst power - path cable loss - attenuator. Bluetooth BLE Channel 00 Wanted signal Blocking signal Blocking signal PER (%) From companion Frequency(MHz) Power(dBm) Pmin + 6dB Pmin + 6dB Pmin + 6dB Pmin + 6dB PER = 3.61 % when Pmin= -92 dbm before blocker is injected. Note: 1. Antenna gain is 1 dbi. 2. Blocking signal power level has offset antenna gain 1 dbi. Bluetooth BLE Channel 39 Wanted signal Blocking signal Blocking signal PER (%) From companion Frequency(MHz) Power(dBm) Pmin + 6dB Pmin + 6dB Pmin + 6dB Pmin + 6dB PER = 6.55 % when Pmin= -91 dbm before blocker is injected. Note: 1. Antenna gain is 1 dbi. 2. Blocking signal power level has offset antenna gain 1 dbi. SPORTON INTERNATIONAL INC. Page Number : 23 of 34 TEL : Report Issued Date : Jun. 30, 2017

24 Report No. : ER Adaptivity Test 5.1 Adaptivity Limit of Adaptivity Only for adaptive systems and RF Output Power > 10 dbm LBT based Detect and Avoid (Load Based Equipment with spectrum sharing mechanism IEEE Std.): LBT based spectrum sharing mechanism may implement in IEEE Std clauses 9, clause 10, clause 16, clause 17, clause 19 and clause 20, or in IEEE Std. IEEE , clause 4, clause 5 and clause 8. Short Control Signaling Transmissions shall have a maximum TxOn / (TxOn + TxOff) ratio of 10 % within an observation period of 50 ms Measurement Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. For conducted measurements on devices with multiple transmit chains and receive chains. The power splitter/combiner shall be used to combine all the transmit/receive chains (antenna outputs) into a single test point. The insertion loss of the power splitter/combiner shall be taken into account Test Setup SPORTON INTERNATIONAL INC. Page Number : 24 of 34 TEL : Report Issued Date : Jun. 30, 2017

25 Report No. : ER Support Unit used in test configuration and system Item Instrument Manufacturer Model No. Characteristics 1. WLAN AP D-LINK DIR-855 Dual Band AP 2. Notebook Lenovo E335 FTP / LAN Test Results of Adaptivity Test Equipment Information: Non-Adaptive Equipment The maximum RF output power (E.I.R.P.) dbm: The maximum (Corresponding) Duty Cycle : % Adaptive Equipment without the possibility to switch to a non-adaptive mode: The equipment has implemented an LBT based DAA mechanism: The equipment is Frame Based equipment The equipment is Load Based equipment The equipment can switch dynamically between Frame Based and Load Based equipment The equipment has implemented an non-lbt based DAA mechanism The equipment can operate in more than one adaptive mode Adaptive Frequency Hopping using other forms of DAA (non-lbt based) Adaptive Equipment which can also operate in non-adaptive mode Data Rate Nominal Modulation (single) Bandwidth BT Nom GFSK 1Mbit/s 1MHz Note: The CCA time is declared by the manufacturer. Channel Test Frequency Test Result MHz PASS MHz PASS SPORTON INTERNATIONAL INC. Page Number : 25 of 34 TEL : Report Issued Date : Jun. 30, 2017

26 Report No. : ER Test Plots of Adaptivity Test Bluetooth 2402MHz Maximum Channel Occupancy Time = 134.7μs Minimum Idle Period = 31.06ms SPORTON INTERNATIONAL INC. Page Number : 26 of 34 TEL : Report Issued Date : Jun. 30, 2017

27 Report No. : ER Bluetooth 2480MHz Maximum Channel Occupancy Time = 141.4μs Minimum Idle Period = 24.76ms SPORTON INTERNATIONAL INC. Page Number : 27 of 34 TEL : Report Issued Date : Jun. 30, 2017

28 Report No. : ER Bluetooth 2402MHz AWGN (Interference) Detection Level = dBm/MHz Interference dwell time = 60 seconds Transmission abort within Maximum Channel Occupancy Time after interference added and the short control signaling is less than 10% duty cycle SPORTON INTERNATIONAL INC. Page Number : 28 of 34 TEL : Report Issued Date : Jun. 30, 2017

29 Report No. : ER Bluetooth 2402MHz AWGN (Interference) + CW (Unwanted Signal) Detection Level = dBm/MHz Interference dwell time = 60 seconds Transmission abort within Maximum Channel Occupancy Time after interference added and the short control signaling is less than 10% duty cycle Note: Detection Level = -70 dbm/mhz + 10 log 10 (100 mw / Pout) + Gain for conducted measurement. (Pout in mw e.i.r.p.) SPORTON INTERNATIONAL INC. Page Number : 29 of 34 TEL : Report Issued Date : Jun. 30, 2017

30 Report No. : ER Bluetooth 2480MHz AWGN (Interference) Detection Level = dBm/MHz Interference dwell time = 60 seconds Transmission abort within Maximum Channel Occupancy Time after interference added and the short control signaling is less than 10% duty cycle SPORTON INTERNATIONAL INC. Page Number : 30 of 34 TEL : Report Issued Date : Jun. 30, 2017

31 Report No. : ER Bluetooth 2480MHz AWGN (Interference) + CW (Unwanted Signal) Detection Level = dBm/MHz Interference dwell time = 60 seconds Transmission abort within Maximum Channel Occupancy Time after interference added and the short control signaling is less than 10% duty cycle Note: Detection Level = -70 dbm/mhz + 10 log 10 (100 mw / Pout) + Gain for conducted measurement. (Pout in mw e.i.r.p.) SPORTON INTERNATIONAL INC. Page Number : 31 of 34 TEL : Report Issued Date : Jun. 30, 2017

32 Report No. : ER Geo-location Capability 6.1 Geo-location Definition and Requirement Geo-location capability is a feature of the equipment to determine its geographical location with the purpose to configure itself according to the regulatory requirements applicable at the geographical location where it operates. The geo-location capability may be present in the equipment or in an external device (temporary) associated with the equipment operating at the same geographical location during the initial power up of the equipment. The geographical location may also be available in equipment already installed and operating at the same geographical location. The geographical location determined by the equipment shall not be accessible to the user Description This device does not support this capability declared by the manufacturer. SPORTON INTERNATIONAL INC. Page Number : 32 of 34 TEL : Report Issued Date : Jun. 30, 2017

33 Report No. : ER List of Measuring Equipment Instrument Manufacturer Model No. Serial No. Characteristics Calibration Date Power Sensor DARE RPR3006W 13I00030SN O31 10MHz~6GHz Sep. 21, 2016 Signal Analyzer Spectrum Analyzer Temperature Chamber Rohde & FSV kHz~30GHz May 02, 2017 Schwarz Rohde & Schwarz FSP kHz-40GHz Jul. 17, 2016 ESPEC SH ~90 Sep. 01, 2016 Test Date Due Date Remark May 23, 2017 ~ Sep. 22, 2017 Jun. 20, 2017 May 23, 2017 ~ May 01, 2018 Jun. 20, 2017 May 23, 2017 ~ Jul. 16, 2017 Jun. 20, 2017 May 23, 2017 ~ Aug. 31, 2017 Jun. 20, 2017 Conducted (TH05-HY) Conducted (TH05-HY) Conducted (TH05-HY) Conducted (TH05-HY) Spectrum Agilent N9010A MY Hz~44GHz Apr. 17, 2017 Jun. 21, 2017 Apr. 16, 2018 Analyzer BT Base Rohde & Jun. 19, 2017 ~ CBT BT 3.0 & 4.0 Jun. 02, 2017 Jun. 01, 2018 Station Schwarz Jun. 20, 2017 Signal Rohde & Jun. 19, 2017 ~ MG3710A kHz~6GHz Dec. 09, 2016 Dec. 08, 2017 Generator Schwarz Jun. 20, 2017 Jun. 19, 2017 ~ Divider Mcli PS kHz~6GHz Feb. 21, 2017 Feb. 20, 2018 Jun. 20, 2017 CSE (03CH15-HY) Conducted (DFS02-HY) Conducted (DFS02-HY) Conducted (DFS02-HY) Signal Generator Signal Generator (Interferer) Agilent E4438C MY KHz ~ 6GHz Sep. 30, 2016 Jun. 23, 2017 Sep. 29, 2017 Rohde & SMJ100A kHz~6GHz Jan. 25, 2017 Jun. 23, 2017 Jan. 24, 2018 Schwarz DFS (DFS02-HY) DFS (DFS02-HY) Spectrum Analyzer Keysight N9010A MY Hz~7GHz Aug. 05, 2016 Jun. 23, 2017 Aug. 04, 2017 Spectrum Analyzer Agilent E4446A MY Hz~44GHz Apr. 26, 2017 Jun. 27, 2017 Apr. 25, 2018 Bilog Antenna Schaffner CBL6112B MHz ~ 2GHz Oct. 15, 2016 Jun. 27, 2017 Oct. 14, 2017 Preamplifier Agilent 8449B 3008A GHz ~ 26.5GHz Nov. 23, 2016 Jun. 27, 2017 Nov. 22, 2017 Horn Antenna ESCO GHz~18GHz Dec. 30, 2016 Jun. 27, 2017 Dec. 29, 2017 Preamplifier Langer EM kHz~3GHz Nov. 01, 2016 Jun. 27, 2017 Oct. 31, 2017 BT Base Rohde & Station Schwarz CBT BT 3.0 & 4.0 Jan. 19, 2017 Jun. 27, 2017 Jan. 18, 2018 Antenna Mast INN-CO MM 3000 N/A 1m~2m NA Jun. 27, 2017 NA Turn Table INN-CO DS Degree 0~ 360 NA Jun. 27, 2017 NA Note: Test equipment calibration is traceable to the procedure of ISO DFS (DFS02-HY) Radiation (05CH02-HY) Radiation (05CH02-HY) Radiation (05CH02-HY) Radiation (05CH02-HY) Radiation (05CH02-HY) Radiation (05CH02-HY) Radiation (05CH02-HY) Radiation (05CH02-HY) SPORTON INTERNATIONAL INC. Page Number : 33 of 34 TEL : Report Issued Date : Jun. 30, 2017

34 Report No. : ER Uncertainty Evaluation Test Item Uncertainty Occupied Channel Bandwidth ± 0.49 % RF output power, conducted ±0.61 db Power density, conducted ±0.60 db Radiated emissions ±2.86 db Temperature ±0.8 C Humidity ±3 % SPORTON INTERNATIONAL INC. Page Number : 34 of 34 TEL : Report Issued Date : Jun. 30, 2017

35 Report Number : ER Appendix A. Test Result of Conducted Test Items Test Engineer: Derek Hsu Temperature: 24~25 C Test Date: 2017/05/23~2017/06/20 Relative Humidity: 54~56 % TEST RESULTS DATA EIRP Power Conducted Power (dbm) Mod. Data Rate NTXChannel Freq. (MHz) Temperature Nomal Extreme Temperature Low Extreme Temperature High Gain (dbi) BTNom 1Mbps BTNom 2Mbps BTNom 3Mbps hopping hopping hopping BLE BLE BLE 1Mbps 1Mbps 1Mbps C -30 C 85 C EIRP Power (dbm) Mod. Data Rate NTXChannel Freq. (MHz) Temperature Nomal Temperature Low Temperature High Limit (dbm) Pass/Fail BTNom 1Mbps BTNom 2Mbps BTNom 3Mbps hopping hopping hopping Pass Pass Pass BLE BLE BLE 1Mbps 1Mbps 1Mbps Pass Pass Pass A-1 of 4

36 Report Number : ER TEST RESULTS DATA EIRP Power Density Power Density Mod. Data Rate NTXChannel Freq. (MHz) EIRP Power Density (dbm/mhz) EIRP Limit (dbm /MHz) Pass/Fail BLE 1Mbps Pass BLE 1Mbps Pass BLE 1Mbps Pass A-2 of 4

37 Report Number : ER TEST RESULTS DATA 99% Occupied Bandwidth Occupied Bandwidth Mod. Data Rate NTXChannel Freq. (MHz) 99% Occupied BW (MHz) Freq. Low (MHz) Freq. High (MHz) Limit (Within operating Band) Pass/Fail BLE 1Mbps 1 0 BLE 1Mbps Pass Pass A-3 of 4

38 Report Number : ER TEST RESULTS DATA OOB Emission Level Mod. Data Rate NTXChannel Freq. (MHz) OOB Emission Worst Level (dbm/mhz) Limit (dbm /MHz) Pass/Fail BLE 1Mbps ,-20 Pass BLE 1Mbps ,-20 Pass A-4 of 4

39 Report No. : ER APPENDIX B. Conducted Spurious Emission Plots BLE TX Conducted Spurious Emission Plots Test Engineer : Rover Lee Temperature : 22~25 Relative Humidity : 51~55% 2.4GHz 2400~2483.5MHz BLE BLE ANT 2.4GHz 2400~2483.5MHz BLE 1 CH MHz CH MHz TX SPORTON INTERNATIONAL INC. TEL : BLE TX FAX : Page Number : 1 of 1

40 Report No. : ER BLE RX Conducted Spurious Emission Plots Test Engineer : Rover Lee Temperature : 22~25 Relative Humidity : 51~55% 2.4GHz 2400~2483.5MHz BLE BLE ANT 2.4GHz 2400~2483.5MHz BLE 1 CH MHz - TX. Left blank SPORTON INTERNATIONAL INC. TEL : BLE RX FAX : Page Number : 1 of 1

41 Report No. : ER APPENDIX C. Cabinet Radiation Plots BLE TX Radiated Spurious Emission Plots Test Engineer : Tom Chiu Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BLE BLE ANT 2.4GHz 2400~2483.5MHz BLE CH MHz 1 Horizontal Vertical TX SPORTON INTERNATIONAL INC. TEL : BLE TX FAX : Page Number : 1 of 2

42 Report No. : ER BLE ANT 2.4GHz 2400~2483.5MHz BLE CH MHz 1 Horizontal Vertical TX SPORTON INTERNATIONAL INC. TEL : BLE TX FAX : Page Number : 2 of 2

43 Report No. : ER BLE RX Radiated Spurious Emission Plots Test Engineer : Tom Chiu Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BLE BLE ANT 2.4GHz 2400~2483.5MHz BLE CH MHz 1 Horizontal Vertical RX SPORTON INTERNATIONAL INC. TEL : BLE RX FAX : Page Number : 1 of 1

44 Report No. : ER Appendix D. Photographs of Radiated Emission Test Configuration <LF> <HF> SPORTON INTERNATIONAL INC. Page Number : D-1 of 1 TEL : FAX :

45 Report No. : ER Appendix E. Original Report Please refer to Sporton report number ER as below. SPORTON INTERNATIONAL INC. Page Number : E1 of E1 TEL : FAX :

46 Report No. : ER CE Radio Test Report APPLICANT EQUIPMENT BRAND NAME MODEL NAME MARKETING NAME : Texas Instruments Incorporated : CC2564 Bluetooth HCI Module : Texas Instruments : CC2564MODN : CC2564MODN Bluetooth Host Controller Interface (HCI) Module STANDARD : ETSI EN V2.1.1 ( ) TEST DATE(S) : May 23, 2017 ~ Jun. 11, 2017 The measurement shown in this test report is tested in accordance with the test procedures given in ETSI EN V2.1.1 ( ). The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Joseph Lin / Supervisor Approved by: Jones Tsai / Manager SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1st Rd.,Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan R.O.C. SPORTON INTERNATIONAL INC. Page Number : 1 of 34 TEL : Report Issued Date : Jun. 15, 2017

47 Report No. : ER TABLE OF CONTENTS REVISION HISTORY... 3 SUMMARY OF TEST RESULT GENERAL DESCRIPTION Applicant Manufacturer Product Feature of Equipment Under Test Modification of EUT Testing Facility Applied Standards Test Condition TEST CONFIGURATION OF EQUIPMENT UNDER TEST Descriptions of Test Mode Connection Diagram of Test System Supported Unit used in test configuration and system EUT Operation Test Setup TRANSMITTER PARAMETERS Maximum Transmit Power Maximum Equivalent Isotropically Radiated Power (E.I.R.P.) Spectral Density Occupied Channel Bandwidth Frequency Hopping Requirements Transmitter unwanted emissions in the out-of-band domain Transmitter spurious emissions RECEIVER PARAMETERS Receiver spurious emissions Receiver Blocking Test ADAPTIVITY TEST Adaptivity GEO-LOCATION CAPABILITY Geo-location LIST OF MEASURING EQUIPMENT UNCERTAINTY EVALUATION APPENDIX A. TEST RESULT OF CONDUCTED TEST ITEMS APPENDIX B. CONDUCTED SPURIOUS EMISSION PLOTS APPENDIX C. CABINET RADIATION PLOTS APPENDIX D. PHOTOGRAPHS OF RADIATED EMISSION TEST CONFIGURATION SPORTON INTERNATIONAL INC. Page Number : 2 of 34 TEL : Report Issued Date : Jun. 15, 2017

48 Report No. : ER REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE ER Rev. 01 Initial issue of report Jun. 15, 2017 SPORTON INTERNATIONAL INC. Page Number : 3 of 34 TEL : Report Issued Date : Jun. 15, 2017

49 Report No. : ER SUMMARY OF TEST RESULT CLAUSE (EN ) TEST PARAMETER PASS/FAIL REMARK Transmitter Parameters Maximum Transmit Power PASS - Maximum Equivalent Isotropically Radiated Power (E.I.R.P.) Spectral Density PASS Only applicable for modulations other than FHSS Occupied Channel Bandwidth PASS - Frequency Hopping Requirements PASS Only applicable for FHSS Transmitter spurious emissions in OOB PASS - Transmitter spurious emissions PASS Under limit db at MHz Receiver Parameters Receiver spurious emissions PASS Under limit 8.77 db at MHz Adaptive Test Item Adaptivity Not Required Only applicable for adaptive equipment Receiver Blocking PASS Output Power >10dBm Non-Adaptive Test Item Duty cycle, Tx-Sequence, Tx-gap Not Required Only applicable for non-adaptive equipment Medium Utilisation (MU) factor Not Required Output Power >10dBm SPORTON INTERNATIONAL INC. Page Number : 4 of 34 TEL : Report Issued Date : Jun. 15, 2017

50 Report No. : ER General Description 1.1 Applicant Texas Instruments Incorporated TI BLVD., Dallas Texas, Manufacturer Texas Instruments Incorporated TI BLVD., Dallas Texas, Product Feature of Equipment Under Test Specification of the Equipment under Test RF General Information Frequency Bluetooth Ch. Frequency Channel Power Range Data Rate Mode (MHz) Number Setting (MHz) BR V [79] 1 Mbps 0x EDR V [79] 2 Mbps 0x EDR V [79] 3 Mbps 0x LE V [40] 1 Mbps 0x18 Note 1: Bluetooth BR uses a GFSK modulation Note 2: Bluetooth EDR uses a combination of /4-DQPSK and 8DPSK. Note 3: Bluetooth LE (Low energy) uses GFSK modulation Antenna Details Antenna information Brand Antenna Type Model 2.4GHz ~2.5GHz Gain 1 Mag Layers Chip LTA G4S3-A Modification of EUT No modifications are made to the EUT during all test items. SPORTON INTERNATIONAL INC. Page Number : 5 of 34 TEL : Report Issued Date : Jun. 15, 2017

51 Report No. : ER Testing Facility Test Site Test Site Location Test Site No. SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1st Rd.,Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan R.O.C. TEL: FAX: Sporton Site No. : TH05-HY ; DFS02-HY Test Site Test Site Location Test Site No. SPORTON INTERNATIONAL INC. No.58, Aly. 75, Ln. 564, Wenhua 3rd Rd., Kwei-Shan District, Tao Yuan City, Taiwan R.O.C. TEL: FAX: Sporton Site No. : 05CH05-HY ;03CH15-HY 1.6 Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of ETSI EN V2.1.1 ( ). Note: All test items were verified and recorded according to the standards and without any deviation during the test. 1.7 Test Condition Normal Voltage DC 3.6V Normal Temperature 25 Extreme Temperature -30 and 85 Note: The test temperature was between -30 C ~ 85 C by manufacturer request. SPORTON INTERNATIONAL INC. Page Number : 6 of 34 TEL : Report Issued Date : Jun. 15, 2017

52 Report No. : ER Test Configuration of Equipment under Test 2.1 Descriptions of Test Mode a. During testing, the interface cables and equipment positions were varied according to ETSI EN V2.1.1 ( ). b. The complete test system included EUT for RF test. c. Preliminary tests were checked in different data rate and recorded worse in the following tables: Test Modes RF Bluetooth 1Mbps Bluetooth LE GFSK GFSK Tx Bluetooth (1Mbps) CH00 (2402MHz) Bluetooth LE CH00 (2402MHz) Bluetooth (1Mbps) CH78 (2480MHz) Bluetooth LE CH39 (2480MHz) Rx Bluetooth (1Mbps) CH78 (2480MHz) Bluetooth LE CH39 (2480MHz) SPORTON INTERNATIONAL INC. Page Number : 7 of 34 TEL : Report Issued Date : Jun. 15, 2017

53 Report No. : ER Connection Diagram of Test System System Simulator AP router Notebook GPS Station BT Earphone Power Source EUT Notebook Cradle Earphone ipod WLAN AP Monitor This example is connection diagram of EUT test configurations.. For detail, please refer to test mode configuration and setup photographs for each test item. 2.3 Supported Unit used in test configuration and system Item Equipment Trade Name Model Name FCC ID Data Cable Power Cord 1. Notebook Lenovo E335 FCC DoC N/A AC I/P: Unshielded, 1.2 m DC O/P: Shielded, 1.8 m 2.4 EUT Operation Test Setup For Bluetooth test items, an engineering test program (HCITester) was provided and enabled to make EUT contact with Bluetooth base station for continuous transmitting and receiving signals. For Bluetooth 4.1 LE test items, an engineering test program (HCITester) was provided and enabled to make EUT continuous transmitting and receiving signals SPORTON INTERNATIONAL INC. Page Number : 8 of 34 TEL : Report Issued Date : Jun. 15, 2017

54 Report No. : ER Transmitter Parameters 3.1 Maximum Transmit Power Limit of Effective Isotropic Radiated Power SUBCLAUSE and TEST CONDITION LIMIT Normal and Extreme Temperature Conditions 20dBm (e.i.r.p) Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedure 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. Placing the EUT in thermal chamber. 3. The EUT is connected to external power supply. 4. Setting thermal chamber temperature and power supply voltage at suitable values. 5. The EIRP = A+G+Y, where A is the power measured, G is the assembly gain of the individual antenna of the EUT in dbi and Y is the additional beamforming gain of the EUT in db if applicable, here, Y=0. 6. The measurement duration is at least 1 second to ensure a minimum number of bursts (at least 10) are captured Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 9 of 34 TEL : Report Issued Date : Jun. 15, 2017

55 Report No. : ER Maximum Equivalent Isotropically Radiated Power (E.I.R.P.) Spectral Density Limit of Maximum Power Spectral Density TEST CONDITION Normal and Extreme Temperature Conditions SUBCLAUSE LIMIT 10dBm / MHz Remark: Maximum spectral power density is not applicable to FHSS system device Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedure 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. These measurements shall only be performed at normal test conditions. 3. The measurement shall be repeated for the equipment being configured to operate at the lowest, the middle, and the highest frequency of the stated frequency range. 4. The test procedure shall be as follows: Step 1: Connect the EUT to the spectrum analyzer and use the following settings: Start Frequency 2400MHz Stop Frequency MHz Resolution BW 10kHz Video BW 30kHz Sweep Points 8350 Detector RMS Trace Mode Max Hold Sweep time 10 sec SPORTON INTERNATIONAL INC. Page Number : 10 of 34 TEL : Report Issued Date : Jun. 15, 2017

56 Report No. : ER Step 2: Add up the values for amplitude (power) for all the samples in the file. Step 3: Normalize the individual values for amplitude so that the sum is equal to the RF Output Power (e.i.r.p.) measured. Step 4: Starting from the first sample in the file (lowest frequency), add up the power of the following samples representing a 1 MHz segment and record the results for power and position (i.e. sample #1 to #100). This is the Power Spectral Density (e.i.r.p.) for the first 1 MHz segment which shall be recorded. Step 5: Shift the start point of the samples added up in step 4 by 1 sample and repeat the procedure in step 4 (i.e. sample #2 to #101). Step 6: Repeat step 5 until the end of the data set and record the radiated Power Spectral Density values for each of the 1 MHz segments. From all the recorded results, the highest value is the maximum Power Spectral Density for the EUT. This value shall be recorded in the test report Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 11 of 34 TEL : Report Issued Date : Jun. 15, 2017

57 Report No. : ER Occupied Channel Bandwidth Limit of Occupied Channel Bandwidth Occupied Channel Bandwidth fall completely within 2.4 GHz GHz Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedure 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. The measurement shall be performed only on the lowest and the highest frequency within the stated frequency range. 3. The test procedure shall be as follows: Step 1: Connect the EUT to the spectrum analyzer and use the following settings: Center Frequency Channel under test Resolution BW 1 % of the span Video BW 3 RBW Frequency Span 2 Nominal Channel Bandwidth Detector RMS Trace Mode Max Hold Sweep Time 1 s Step 2: Wait until the trace is completed. Find the peak value of the trace and place the analyzer marker on this peak. Step 3: Use the 99 % bandwidth function of the spectrum analyzer to measure the Occupied Channel Bandwidth of the EUT. SPORTON INTERNATIONAL INC. Page Number : 12 of 34 TEL : Report Issued Date : Jun. 15, 2017

58 Report No. : ER Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 13 of 34 TEL : Report Issued Date : Jun. 15, 2017

59 Report No. : ER Frequency Hopping Requirements Dwell Time and Minimum Frequency Occupation Time Limit of Dwell Time SUBCLAUSE TEST CONDITION LIMIT Non-Adaptive Frequency Hopping Systems 15 ms within 15ms * hopping frequencies (N) Adaptive Frequency Hopping Systems 0.4s within 0.4s * hopping frequencies (N) Limit of Minimum Frequency Occupation Time TEST CONDITION Normal Condition SUBCLAUSE LIMIT Option1: The Minimum Frequency Occupation Time shall be equal to one dwell time within a period not exceeding four times the product of the dwell time per hop and the number of hopping frequencies in use. Remark: This test item is not applicable to DSSS/OFDM device Measuring Instruments The measuring equipment is listed in the section 8 of this test report. SPORTON INTERNATIONAL INC. Page Number : 14 of 34 TEL : Report Issued Date : Jun. 15, 2017

60 Report No. : ER Test Procedures 1. The measurement shall be performed on a minimum of 2 hopping frequencies chosen arbitrary from the actual hopping sequence. The results as well as the frequencies on which the test was performed shall be recorded in the test report. 2. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 3. The analyzer shall be set as follows: Center Frequency Frequency Span Resolution BW Video BW Detector Sweep time Channel under test 0 Hz 300kHz 300kHz RMS Equal to the Dwell Time Minimum number of hopping frequencies (N) Number of sweep points Trace Mode Clear / Write Trigger Free Run 4. For accuracy measurement, the sweep time would be zoomed in and verify the dwell time which is from the dwell time per hop across the total number of hopping channel. Then record test result. 5. Make the following changes on the analyzer to get Minimum Frequency Occupation Time Sweep time: Equal to 4 Dwell Time Actual number of hopping frequencies in use Test Setup Test Results Please refer to Appendix A Test Plots SPORTON INTERNATIONAL INC. Page Number : 15 of 34 TEL : Report Issued Date : Jun. 15, 2017

61 Report No. : ER Dwell Time - Channel 00 DH1 Frequency Occupation Time - Channel 00 DH1 Dwell Time - Channel 00 DH3 Frequency Occupation Time - Channel 00 DH3 Dwell Time - Channel 00 DH5 Frequency Occupation Time - Channel 00 DH5 SPORTON INTERNATIONAL INC. Page Number : 16 of 34 TEL : Report Issued Date : Jun. 15, 2017

62 Report No. : ER Dwell Time - Channel 78 DH1 Frequency Occupation Time - Channel 78 DH1 Dwell Time - Channel 78 DH3 Frequency Occupation Time - Channel 78 DH3 Dwell Time - Channel 78 DH5 Frequency Occupation Time - Channel 78 DH5 SPORTON INTERNATIONAL INC. Page Number : 17 of 34 TEL : Report Issued Date : Jun. 15, 2017

63 Report No. : ER Hopping Sequence Limit of Hopping Sequence TEST CONDITION SUBCLAUSE LIMIT Non-Adaptive Frequency Hopping Systems Adaptive Frequency Hopping Systems N N Ch 70% of band N= 15 or 15 divided by the minimum Hopping Frequency Separation in MHz, whichever is the greater. Remark: Hopping Sequence is not applicable to DSSS/OFDM device Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ) Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 18 of 34 TEL : Report Issued Date : Jun. 15, 2017

64 Report No. : ER Test Plots Total Number of Hopping Channel Plot on Channel * RBW 300 khz Delta 2 [T1 ] * VBW 300 khz 3.47 db Ref 20 dbm * Att 20 db * SWT 1 s MHz RM * MAXH 0 Offset 24.2 db D dbm Marker 1 [T1 ] dbm GHz A LVL D dbm DB Start 2.4 GHz 8.35 MHz/ Stop GHz Date: 2.JUN :42:54 SPORTON INTERNATIONAL INC. Page Number : 19 of 34 TEL : Report Issued Date : Jun. 15, 2017

65 Report No. : ER Hopping Frequency Separation Limit of Hopping Frequency Separation SUBCLAUSE TEST CONDITION LIMIT Non-Adaptive Frequency Hopping Systems MAX [ OBW, 100kHz ] Adaptive Frequency Hopping Systems 100kHz Remark: Hopping Frequency Separation is not applicable to DSSS/OFDM device Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. These measurements shall only be performed at normal test conditions. 2. The measurement shall be performed on 2 adjacent hopping frequencies. 3. The frequencies on which the test was performed shall be recorded. 4. The measurement procedure follows the clause Option 2 of the ETSI EN V2.1.1 ( ) Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 20 of 34 TEL : Report Issued Date : Jun. 15, 2017

66 Report No. : ER Transmitter unwanted emissions in the out-of-band domain Transmitter unwanted emissions in the out-of-band domain limit out-of-band domain limit Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. These measurements shall only be performed at normal test conditions. 3. For conducted measurements on devices with multiple transmit chains using the results for each of the transmit chains for the corresponding 1 MHz segments shall be added and compared with the transmit mask limit Test Setup Test Results Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 21 of 34 TEL : Report Issued Date : Jun. 15, 2017

67 Report No. : ER Bluetooth Normal mode and Bluetooth 4.1 LE OOB worse case SPORTON INTERNATIONAL INC. Page Number : 22 of 34 TEL : Report Issued Date : Jun. 15, 2017

68 Report No. : ER Transmitter spurious emissions Limit of Transmitter spurious emissions In case of equipment with antenna connectors, these limits apply to emissions at the antenna port (conducted). For emissions radiated by the cabinet or emissions radiated by integral antenna equipment (without antenna connectors), these limits are e.r.p. for emissions up to 1 GHz and as e.i.r.p. for emissions above 1 GHz. SUBCLAUSE and FREQUENCY RANGE MAXIMUM POWER BANDWIDTH 30 MHz to 47 MHz -36 dbm 100 khz 47 MHz to 74 MHz -54 dbm 100 khz 74 MHz to 87,5 MHz -36 dbm 100 khz 87,5 MHz to 118 MHz -54 dbm 100 khz 118 MHz to 174 MHz -36 dbm 100 khz 174 MHz to 230 MHz -54 dbm 100 khz 230 MHz to 470 MHz -36 dbm 100 khz 470 MHz to 862 MHz -54 dbm 100 khz 862 MHz to 1 GHz -36 dbm 100 khz 1 GHz to 12,75 GHz -30 dbm 1 MHz Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. The EUT was placed on a turntable with 1.5m height. 3. The test distance between the receiving antenna and the EUT is 3meter below 1GHz frequency range, and 3 meter which is in far field test condition for measured frequency above 1GHz, while the receiving (test) antenna is kept at 1.5 meter height. 4. Set EUT in continuous transmitting with maximum output power. 5. The table was rotated from 0 to 360 degree to search the highest radiated emission. 6. Repeating step 3 and 4 for each polarization and channel to find the worst emission level. 7. The results obtained are compared to the limits in order to prove compliance with the requirement. SPORTON INTERNATIONAL INC. Page Number : 23 of 34 TEL : Report Issued Date : Jun. 15, 2017

69 Report No. : ER Test Setup <Below 1GHz> <Above 1GHz> Test Results Please refer to Appendix B. SPORTON INTERNATIONAL INC. Page Number : 24 of 34 TEL : Report Issued Date : Jun. 15, 2017

70 Report No. : ER Receiver Parameters 4.1 Receiver spurious emissions Limit of Receiver spurious emissions In case of equipment with antenna connectors, these limits apply to emissions at the antenna port (conducted). For emissions radiated by the cabinet or emissions radiated by integral antenna equipment (without antenna connectors), these limits are e.r.p. for emissions up to 1 GHz and as e.i.r.p. for emissions above 1 GHz. SUBCLAUSE and FREQUENCY RANGE MAXIMUM POWER BANDWIDTH 30 MHz to 1 GHz -57 dbm 100kHz 1 GHz to 12,75 GHz -47 dbm 1MHz Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. The EUT was placed on a turntable with 1.5m height. 3. The test distance between the receiving antenna and the EUT is 3meter below 1GHz frequency range, and 3 meter which is in far field test condition for measured frequency above 1GHz, while the receiving (test) antenna is kept at 1.5 meter height. 4. Set EUT in receiving mode. 5. The table was rotated from 0 to 360 degree to search the highest radiated emission. 6. Repeating step 3 and 4 for each polarization and channel to find the worst emission level. 7. The results obtained are compared to the limits in order to prove compliance with the requirement. SPORTON INTERNATIONAL INC. Page Number : 25 of 34 TEL : Report Issued Date : Jun. 15, 2017

71 Report No. : ER Test Setup <Below 1GHz> <Above 1GHz> Test Results Please refer to Appendix B. SPORTON INTERNATIONAL INC. Page Number : 26 of 34 TEL : Report Issued Date : Jun. 15, 2017

72 Report No. : ER Receiver Blocking Test Limit of Receiver Blocking Test Receiver category 1 1. Adaptive equipment with maximum RF output power > 10dBm e.i.r.p. (EX: WiFi) Receiver category 2 1. Non-adaptive equipment with MU 1% ~ 10% 2. Adaptive equipment with Maximum RF output power < 10dBm e.i.r.p. (EX: Bluetooth) SPORTON INTERNATIONAL INC. Page Number : 27 of 34 TEL : Report Issued Date : Jun. 15, 2017

73 Report No. : ER Receiver category 3 1. Non-adaptive equipment with MU < 1% 2. Adaptive equipment with Maximum RF output power < 0dBm e.i.r.p Measuring Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. For systems using multiple receive chains only one chain (antenna port) need to be tested. All other receiver inputs shall be terminated Test Setup SPORTON INTERNATIONAL INC. Page Number : 28 of 34 TEL : Report Issued Date : Jun. 15, 2017

74 Report No. : ER Test Results of Receiver Blocking Pmin = CMW500 burst power - path cable loss - attenuator. Bluetooth 1Mbps hopping mode Wanted signal Blocking signal Blocking signal PER (%) From companion Frequency(MHz) Power(dBm) Pmin + 6dB Pmin + 6dB Pmin + 6dB Pmin + 6dB PER = 8.76 % when Pmin= -97 dbm before blocker is injected. Note: 1. Antenna gain is dbi. 2. Blocking signal power level has offset antenna gain dbi. Bluetooth BLE Channel 00 Wanted signal Blocking signal Blocking signal PER (%) From companion Frequency(MHz) Power(dBm) Pmin + 6dB Pmin + 6dB Pmin + 6dB Pmin + 6dB PER = 4.44 % when Pmin= -95 dbm before blocker is injected. Note: 1. Antenna gain is dbi. 2. Blocking signal power level has offset antenna gain dbi. Bluetooth BLE Channel 39 Wanted signal Blocking signal Blocking signal PER (%) From companion Frequency(MHz) Power(dBm) Pmin + 6dB Pmin + 6dB Pmin + 6dB Pmin + 6dB PER = 5.55 % when Pmin= -95 dbm before blocker is injected. Note: 1. Antenna gain is dbi. 2. Blocking signal power level has offset antenna gain dbi. SPORTON INTERNATIONAL INC. Page Number : 29 of 34 TEL : Report Issued Date : Jun. 15, 2017

75 Report No. : ER Adaptivity Test 5.1 Adaptivity Limit of Adaptivity Only for adaptive systems and RF Output Power > 10 dbm LBT based Detect and Avoid (Load Based Equipment with spectrum sharing mechanism IEEE Std.): LBT based spectrum sharing mechanism may implement in IEEE Std clauses 9, clause 10, clause 16, clause 17, clause 19 and clause 20, or in IEEE Std. IEEE , clause 4, clause 5 and clause 8. Short Control Signaling Transmissions shall have a maximum TxOn / (TxOn + TxOff) ratio of 10 % within an observation period of 50 ms Measurement Instruments The measuring equipment is listed in the section 8 of this test report Test Procedures 1. The measurement procedure follows the clause of the ETSI EN V2.1.1 ( ). 2. For conducted measurements on devices with multiple transmit chains and receive chains. The power splitter/combiner shall be used to combine all the transmit/receive chains (antenna outputs) into a single test point. The insertion loss of the power splitter/combiner shall be taken into account Test Setup SPORTON INTERNATIONAL INC. Page Number : 30 of 34 TEL : Report Issued Date : Jun. 15, 2017

76 Report No. : ER Support Unit used in test configuration and system Item Instrument Manufacturer Model No. Characteristics 1. WLAN AP D-LINK DIR-855 Dual Band AP 2. Notebook Lenovo E335 FTP / LAN Test Results of Adaptivity Test Not Applicable. SPORTON INTERNATIONAL INC. Page Number : 31 of 34 TEL : Report Issued Date : Jun. 15, 2017

77 Report No. : ER Geo-location Capability 6.1 Geo-location Definition and Requirement Geo-location capability is a feature of the equipment to determine its geographical location with the purpose to configure itself according to the regulatory requirements applicable at the geographical location where it operates. The geo-location capability may be present in the equipment or in an external device (temporary) associated with the equipment operating at the same geographical location during the initial power up of the equipment. The geographical location may also be available in equipment already installed and operating at the same geographical location. The geographical location determined by the equipment shall not be accessible to the user Description This device does not support this capability declared by the manufacturer. SPORTON INTERNATIONAL INC. Page Number : 32 of 34 TEL : Report Issued Date : Jun. 15, 2017

78 Report No. : ER List of Measuring Equipment Calibration Instrument Manufacturer Model No. Serial No. Characteristics Test Date Due Date Remark Date 13I00030SN May 23, 2017 ~ Conducted Power Sensor DARE RPR3006W 10MHz~6GHz Sep. 21, 2016 Sep. 22, 2017 O31 Jun. 26, 2017 (TH05-HY) Signal Analyzer Spectrum Analyzer Temperature Chamber Spectrum Analyzer Base Station Signal Generator Rohde & May 23, 2017 ~ Conducted FSV kHz~30GHz May 02, 2017 May 01, 2018 Schwarz Jun. 26, 2017 (TH05-HY) Rohde & May 23, 2017 ~ FSP kHz-40GHz Jul. 17, 2016 Jul. 16, 2017 Schwarz Jun. 26, 2017 May 23, 2017 ~ ESPEC SH ~90 Sep. 01, 2016 Aug. 31, 2017 Jun. 26, 2017 May 23, 2017 ~ Agilent E4445A MY Hz~13.2GHz Nov. 28,2016 Nov. 27,2017 May 25, 2017 GSM/GPRS/WC Rohde & May 23, 2017 ~ CMW DMA/FD-LTE/TD Dec. 14, 2016 Dec. 13, 2017 Schwarz May 25, LTE/MIMO CW Signal May 23, 2017 ~ Agilent E8247C MY Sep. 30, 2016 Sep. 29, 2017 Generator May 25, 2017 Bilog Antenna Teseq GmbH CBL6112D MHz~2GHz Oct. 15, 2016 Jun. 10, 2017 Oct. 14, 2017 Double Ridge Horn Antenna EMCO GHz ~ 18GHz Jul. 14, 2016 Jun. 10, 2017 Jul. 13, 2017 Signal Analyzer Rohde & Schwarz FSV Hz~30GHz Jan. 04, 2017 Jun. 10, 2017 Jan. 03, 2018 Preamplifier Agilent 8449B 3008A GHz~26.5GHz Dec. 27, 2016 Jun. 10, 2017 Dec. 26, 2017 Amplifier EMCI EMC MHz~8GHz Jan. 17, 2017 Jun. 10, 2017 Jan. 16, 2018 Antenna Mast ChainTek MD m~4m N/A Jun. 10, 2017 N/A Turn Table EMEC TT 2000 N/A degree N/A Jun. 10, 2017 N/A Spectrum Analyzer Agilent N9030A MY Hz~44GHz Mar. 23, 2017 Jun. 11, 2017 Mar. 22, 2018 BT Base Rohde & CBT BT 3.0 Sep. 08, 2016 Jun. 11, 2017 Sep Station Schwarz Note: Test equipment calibration is traceable to the procedure of ISO Conducted (TH05-HY) Conducted (TH05-HY) Conducted (DFS02-HY) Conducted (DFS02-HY) Conducted (DFS02-HY) Radiation (05CH05-HY) Radiation (05CH05-HY) Radiation (05CH05-HY) Radiation (05CH05-HY) Radiation (05CH05-HY) Radiation (05CH05-HY) Radiation (05CH05-HY) Radiation (03CH15-HY) Radiation (03CH15-HY) SPORTON INTERNATIONAL INC. Page Number : 33 of 34 TEL : Report Issued Date : Jun. 15, 2017

79 Report No. : ER Uncertainty Evaluation Test Item Uncertainty Occupied Channel Bandwidth ± 0.49 % RF output power, conducted ±0.61 db Power density, conducted ±0.60 db Radiated emissions ±2.86 db Temperature ±0.8 C Humidity ±3 % SPORTON INTERNATIONAL INC. Page Number : 34 of 34 TEL : Report Issued Date : Jun. 15, 2017

80 Appendix A. Test Result of Conducted Test Items Report Number : ER Test Engineer: Derek Hsu Temperature: 24~25 C Test Date: 2017/05/23~2017/06/06 Relative Humidity: 54~56 % TEST RESULTS DATA EIRP Power Conducted Power (dbm) Mod. Data Rate NTXChannel Freq. (MHz) Temperature Nomal Extreme Temperature Low Extreme Temperature High Gain (dbi) BTNom 1Mbps BTNom 2Mbps BTNom 3Mbps hopping hopping hopping BLE BLE BLE 1Mbps 1Mbps 1Mbps C -30 C 85 C EIRP Power (dbm) Mod. Data Rate NTXChannel Freq. (MHz) Temperature Nomal Temperature Low Temperature High Limit (dbm) Pass/Fail BTNom 1Mbps BTNom 2Mbps BTNom 3Mbps 1 hopping Pass 1 hopping Pass 1 hopping Pass BLE 1Mbps Pass BLE 1Mbps Pass BLE 1Mbps Pass A-1 of 5

81 Report Number : ER TEST RESULTS DATA EIRP Power Density Power Density Mod. Data Rate NTXChannel Freq. (MHz) EIRP Power Density (dbm/mhz) EIRP Limit (dbm /MHz) Pass/Fail BLE 1Mbps Pass BLE 1Mbps Pass BLE 1Mbps Pass A-2 of 5

82 Report Number : ER TEST RESULTS DATA 99% Occupied Bandwidth Occupied Bandwidth Mod. Data Rate NTXChannel Freq. (MHz) 99% Occupied BW (MHz) Freq. Low (MHz) Freq. High (MHz) Limit (Within operating Band) Pass/Fail BTNom 1Mbps BTNom 1Mbps BTNom 2Mbps BTNom 2Mbps BTNom 3Mbps BTNom 3Mbps BLE BLE 1Mbps 1Mbps Pass Pass Pass Pass Pass Pass Pass Pass A-3 of 5

83 Report Number : ER TEST RESULTS DATA OOB Emission Level Mod. Data Rate NTXChannel Freq. (MHz) OOB Emission Worst Level (dbm/mhz) Limit (dbm /MHz) Pass/Fail BTNom 1Mbps BTNom 2Mbps BTNom 3Mbps hopping hopping hopping ,-20-10,-20-10,-20 Pass Pass Pass BLE BLE 1Mbps 1Mbps ,-20-10,-20 Pass Pass A-4 of 5

84 Report Number : ER TEST RESULTS DATA Bluetooth Test Items Dwell Time of each Frequency Measurement BT (Hopping Mode) Dwell Time per hop(ms) Dwell Time(ms) Dwell Time Max. Limit (ms) Frequency Occupation Time Hop# (ms) Frequency Occupation Time min. Limit (ms) Pass /Fail 2402 MHz Pass DH MHz Pass 2402 MHz Pass DH MHz Pass 2402 MHz Pass DH MHz Pass Hopping Sequence Measurement Total Number of Hopping Frequency 20dBc Operating Range (MHz) Limit of operating range (at least 70% of band) (MHz) Minimum Number of Adaptive Frequency Hopping Limit of hopping frequencies at all times Hopping Channel Separation Measurement BT Separation(MHz) Limit(MHz) Pass /Fail CH 00 CH 39 CH >0.1 >0.1 >0.1 Pass Pass Pass A-5 of 5

85 Report No. : ER Appendix B. Conducted Spurious Emission Plots BT TX Conducted Spurious Emission Plots Test Engineer : Karl Hou Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BT BT ANT 2.4GHz 2400~2483.5MHz BT 1 CH MHz CH MHz TX SPORTON INTERNATIONAL INC. TEL : WLAN TX FAX : Page Number : 1 of 1

86 Report No. : ER BLE TX Conducted Spurious Emission Plots Test Engineer : Karl Hou Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BLE BLE ANT 2.4GHz 2400~2483.5MHz BLE 1 CH MHz CH MHz TX SPORTON INTERNATIONAL INC. TEL : WLAN TX FAX : Page Number : 1 of 1

87 Report No. : ER BT RX Conducted Spurious Emission Plots Test Engineer : Karl Hou Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BT BT ANT 2.4GHz 2400~2483.5MHz BT 1 CH MHz - TX. Left blank SPORTON INTERNATIONAL INC. TEL : WLAN RX FAX : Page Number : 1 of 1

88 Report No. : ER BLE RX Conducted Spurious Emission Plots Test Engineer : Karl Hou Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BLE BLE ANT 2.4GHz 2400~2483.5MHz BLE 1 CH MHz - TX. Left blank SPORTON INTERNATIONAL INC. TEL : WLAN RX FAX : Page Number : 1 of 1

89 Report No. : ER Appendix C. Cabinet Radiation Plots BT TX Radiated Spurious Emission Plots Test Engineer : Nick Chang Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BT BT ANT 2.4GHz 2400~2483.5MHz BT CH MHz 1 Horizontal Vertical TX SPORTON INTERNATIONAL INC. TEL : BT TX FAX : Page Number : 1 of 2

90 Report No. : ER BT ANT 2.4GHz 2400~2483.5MHz BT CH MHz 1 Horizontal Vertical TX SPORTON INTERNATIONAL INC. TEL : BT TX FAX : Page Number : 2 of 2

91 Report No. : ER BLE TX Radiated Spurious Emission Plots Test Engineer : Nick Chang Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BLE BLE ANT 2.4GHz 2400~2483.5MHz BLE CH MHz 1 Horizontal Vertical TX SPORTON INTERNATIONAL INC. TEL : BLE TX FAX : Page Number : 1 of 2

92 Report No. : ER BLE ANT 2.4GHz 2400~2483.5MHz BLE CH MHz 1 Horizontal Vertical TX SPORTON INTERNATIONAL INC. TEL : BLE TX FAX : Page Number : 2 of 2

93 Report No. : ER BT RX Radiated Spurious Emission Plots Test Engineer : Nick Chang Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BT BT ANT 2.4GHz 2400~2483.5MHz BT CH MHz 1 Horizontal Vertical RX SPORTON INTERNATIONAL INC. TEL : BT RX FAX : Page Number : 1 of 1

94 Report No. : ER BLE RX Radiated Spurious Emission Plots Test Engineer : Nick Chang Temperature : 21~22 Relative Humidity : 45~46% 2.4GHz 2400~2483.5MHz BLE BLE ANT 2.4GHz 2400~2483.5MHz BLE CH MHz 1 Horizontal Vertical RX SPORTON INTERNATIONAL INC. TEL : BLE RX FAX : Page Number : 1 of 1

95 Report No. : ER Appendix D. Photographs of Radiated Emission Test Configuration SPORTON INTERNATIONAL INC. Page Number : D-1 of 1 TEL : FAX :