Selection Table RECEIVER/ DRIVER ENABLE LOW-POWER SHUTDOWN. Yes Yes No Yes No No No No No. Yes Yes Yes Yes No Yes No Yes Yes
|
|
- Noreen Marshall
- 6 years ago
- Views:
Transcription
1 9-22; ev 7; 6/3 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers General escription The MX4, MX43, MX45, MX47 MX49, and MX47 are low-power traceivers for S-45 and S- 422 communication. Each part contai one driver and one receiver. The MX43, MX47, MX4, and MX49 feature reduced slew-rate drivers that minimize EMI and reduce reflectio caused by improperly terminated cables, thus allowing error-free data tramission up to 25kbps. The driver slew rates of the MX4, MX45, MX49, MX49, and MX47 are not limited, allowing them to tramit up to 2.5Mbps. These traceivers draw between 2µ and 5µ of supply current when unloaded or fully loaded with disabled drivers. dditionally, the MX4, MX43, and MX47 have a low-current shutdown mode in which they coume only.µ. ll parts operate from a single 5 supply. rivers are short-circuit current limited and are protected agait excessive power dissipation by thermal shutdown circuitry that places the driver outputs into a high-impedance state. The receiver input has a fail-safe feature that guarantees a logic-high output if the input is open circuit. The MX47 and MX47 feature quarter-unit-load receiver input impedance, allowing up to 2 MX47/ MX47 traceivers on the bus. Full-duplex communicatio are obtained using the MX4 MX49, while the MX4, MX43, MX45, MX47, and MX47 are designed for half-duplex applicatio. pplicatio Low-Power S-45 Traceivers Low-Power S-422 Traceivers Level Tralators Traceivers for EMI-Seitive pplicatio Industrial-Control Local rea Networks Features In µmx Package: Smallest -Pin SO Slew-ate Limited for Error-Free ata Tramission (MX43/47/4/49).µLow-Current Shutdown Mode (MX4/43/47) Low Quiescent Current: 2µ (MX43/47/4/49) 23µ (MX47) 3µ (MX4/45/49/49) -7 to +2 Common-Mode Input oltage ange Three-State Outputs 3 Propagation elays, 5 Skew (MX4/45/49/49/47) Full-uplex and Half-uplex ersio vailable Operate from a Single 5 Supply llows up to 2 Traceivers on the us (MX47/MX47) Current-Limiting and Thermal Shutdown for river Overload Protection Ordering Information PT TEMP NGE PIN-PCKGE MX4CP C to +7 C Plastic P MX4CS C to +7 C SO MX4CU C to +7 C µmx MX4C/ C to +7 C ice* Ordering Information continued at end of data sheet. *Contact factory for dice specificatio. Selection Table PT NUME MX4 MX43 MX45 MX47 MX4 MX49 MX49 MX49 MX47 HLF/FULL UPLEX Half Half Half Half Full Full Full Full Half T TE (Mbps) SLEW-TE LIMITE es es es es LOW-POWE SHUTOWN es es es ECEIE/ IE ENLE es es es es es es es QUIESCENT CUENT (µ) NUME OF TNSMITTES ON US PIN COUNT 4 4 MX4/MX43/MX45/MX47 MX49/MX47 Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/allas irect! at , or visit Maxim s website at ownloaded from Elcodis.com electronic components distributor
2 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 SOLUTE MXIMUM TINGS Supply oltage ( )...2 Control Input oltage (E, E) to ( +.5) river Input oltage () to ( +.5) river Output oltage (, )...- to +2.5 eceiver Input oltage (, )...- to +2.5 eceiver Output oltage () to ( +.5) Continuous Power issipation (T = +7 C) -Pin Plastic P (derate 9.9mW/ C above +7 C)...727mW 4-Pin Plastic P (derate.mw/ C above +7 C)..mW -Pin SO (derate 5.mW/ C above +7 C)...47mW C ELECTICL CHCTEISTICS ( = 5 ±5%, T = T MIN to T MX, unless otherwise noted.) (tes, 2) 4-Pin SO (derate.33mw/ C above +7 C)...667mW -Pin µmx (derate 4.mW/ C above +7 C)...3mW -Pin CEP (derate.mw/ C above +7 C)...64mW 4-Pin CEP (derate 9.9mW/ C above +7 C)...727mW Operating Temperature anges MX4 C /MX47C_... C to +7 C MX4 E /MX47E_...-4 C to +5 C MX4 MJ_/MX47MJ C to +25 C Storage Temperature ange C to +6 C Lead Temperature (soldering, sec)...+3 C Stresses beyond those listed under bsolute Maximum atings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditio beyond those indicated in the operational sectio of the specificatio is not implied. Exposure to absolute maximum rating conditio for extended periods may affect device reliability. PMETE ifferential river Output (no load) ifferential river Output (with load) Change in Magnitude of river ifferential Output oltage for Complementary Output States river Common-Mode Output oltage Change in Magnitude of river Common-Mode Output oltage for Complementary Output States Input High oltage Input Low oltage Input Current Input Current (, ) eceiver ifferential Threshold oltage eceiver Input Hysteresis eceiver Output High oltage eceiver Output Low oltage Three-State (high impedance) Output Current at eceiver eceiver Input esistance SMOL O O2 O OC O IH IL I IN I IN2 TH TH OH OL I O IN = 5Ω (S-422) = 27Ω (S-45), Figure 4 = 27Ω or 5Ω, Figure 4 = 27Ω or 5Ω, Figure 4 = 27Ω or 5Ω, Figure 4 E,, E E,, E E,, E E = ; = or 5.25, all devices except MX47/MX47 MX47/MX47, E =, = or CM 2 CM = I O = -4m, I = 2m I O = 4m, I = -2m.4 O 2.4 CONTIONS -7 CM 2, all devices except MX47/MX47 IN = 2 IN = -7 IN = 2 IN = -7-7 CM 2, MX47/MX47 MIN TP MX ± ± UNITS µ m m m µ kω kω 2 ownloaded from Elcodis.com electronic components distributor
3 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers C ELECTICL CHCTEISTICS (continued) ( = 5 ±5%, T = T MIN to T MX, unless otherwise noted.) (tes, 2) PMETE -Load Supply Current (te 3) Supply Current in Shutdown river Short-Circuit Current, O = High river Short-Circuit Current, O = Low eceiver Short-Circuit Current I OS I OS2 I OS MX MX43/MX47, E = 5 MX E = or E = 2 25 MX4/43/47, E =, E =. -7 O 2 (te 4) -7 O 2 (te 4) O SWITCHING CHCTEISTICS MX4/MX45, MX49/MX49, MX47 ( = 5 ±5%, T = T MIN to T MX, unless otherwise noted.) (tes, 2) PMETE river Input to Output river Output Skew to Output river ise or Fall Time river Enable to Output High river Enable to Output Low river isable Time from Low river isable Time from High eceiver Input to Output t PLH - t PHL ifferential eceiver Skew eceiver Enable to Output Low eceiver Enable to Output High eceiver isable Time from Low eceiver isable Time from High Maximum ata ate Time to Shutdown SMOL I CC I SHN CONTIONS MIN TP MX MX4/MX49, E,, E = or 2 25 MX49/MX49, E,, E = or 3 5 MX4/MX45, E = 5 9 E = or E = 3 5 MX47, E = or E = E = UNITS SMOL CONTIONS MIN TP MX UNITS t PLH Figures 6 and, FF = 54Ω, 3 6 t PHL C L = C L2 = pf 3 6 t SKEW Figures 6 and, FF = 54Ω, C L = C L2 = pf 5 Figures 6 and, MX4, MX45, MX t, t F FF = 54Ω, MX49C/E, MX49C/E C L = C L2 = pf MX49M, MX49M t H Figures 7 and 9, C L = pf, S2 closed 4 7 t L Figures 7 and 9, C L = pf, S closed 4 7 t L Figures 7 and 9, C L = 5pF, S closed 4 7 t H Figures 7 and 9, C L = 5pF, S2 closed 4 7 Figures 6 and, MX4, MX45, MX t PLH, t PHL FF = 54Ω, MX49C/E, MX49C/E C L = C L2 = pf MX49M, MX49M t SK Figures 6 and, FF = 54Ω, C L = C L2 = pf 3 t L Figures 5 and, C L = 5pF, S closed 2 5 t H Figures 5 and, C L = 5pF, S2 closed 2 5 t L Figures 5 and, C L = 5pF, S closed 2 5 t H Figures 5 and, C L = 5pF, S2 closed 2 5 f MX 2.5 Mbps t SHN MX4 (te 5) µ µ m m m MX4/MX43/MX45/MX47 MX49/MX47 3 ownloaded from Elcodis.com electronic components distributor
4 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 SWITCHING CHCTEISTICS MX4/MX45, MX49/MX49, MX47 (continued) ( = 5 ±5%, T = T MIN to T MX, unless otherwise noted.) (tes, 2) PMETE river Enable from Shutdown to Output High (MX4) river Enable from Shutdown to Output Low (MX4) eceiver Enable from Shutdown to Output High (MX4) eceiver Enable from Shutdown to Output Low (MX4) SMOL t H(SHN) t L(SHN) t H(SHN) t L(SHN) CONTIONS Figures 7 and 9, C L = pf, S2 closed Figures 7 and 9, C L = pf, S closed Figures 5 and, C L = 5pF, S2 closed, - = 2 Figures 5 and, C L = 5pF, S closed, - = 2 SWITCHING CHCTEISTICS MX43, MX47/MX4/MX49 ( = 5 ±5%, T = T MIN to T MX, unless otherwise noted.) (tes, 2) PMETE river Input to Output river Output Skew to Output river ise or Fall Time river Enable to Output High river Enable to Output Low river isable Time from Low river isable Time from High eceiver Input to Output I t PLH - t PHL I ifferential eceiver Skew eceiver Enable to Output Low eceiver Enable to Output High eceiver isable Time from Low eceiver isable Time from High Maximum ata ate Time to Shutdown river Enable from Shutdown to Output High river Enable from Shutdown to Output Low eceiver Enable from Shutdown to Output High eceiver Enable from Shutdown to Output Low SMOL CONTIONS t PLH Figures 6 and, FF = 54Ω, t PHL C L = C L2 = pf t SKEW Figures 6 and, FF = 54Ω, C L = C L2 = pf t, t F t H t L t L t H t PLH t PHL t SK t L t H t L t H f MX t SHN t H(SHN) t L(SHN) t H(SHN) t L(SHN) Figures 6 and, FF = 54Ω, C L = C L2 = pf Figures 7 and 9, C L = pf, S2 closed Figures 7 and 9, C L = pf, S closed Figures 7 and 9, C L = 5pF, S closed Figures 7 and 9, C L = 5pF, S2 closed Figures 6 and, FF = 54Ω, C L = C L2 = pf Figures 6 and, FF = 54Ω, C L = C L2 = pf Figures 5 and, C L = 5pF, S closed Figures 5 and, C L = 5pF, S2 closed Figures 5 and, C L = 5pF, S closed Figures 5 and, C L = 5pF, S2 closed t PLH, t PHL < 5% of data period MX43/MX47 (te 5) MX43/MX47, Figures 7 and 9, C L = pf, S2 closed MX43/MX47, Figures 7 and 9, C L = pf, S closed MX43/MX47, Figures 5 and, C L = 5pF, S2 closed MX43/MX47, Figures 5 and, C L = 5pF, S closed MIN TP MX MIN TP MX UNITS UNITS kbps 4 ownloaded from Elcodis.com electronic components distributor
5 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers NOTES FO ELECTICL/SWITCHING CHCTEISTICS te : ll currents into device pi are positive; all currents out of device pi are negative. ll voltages are referenced to device ground unless otherwise specified. te 2: ll typical specificatio are given for = 5 and T = +25 C. te 3: Supply current specification is valid for loaded tramitters when E =. te 4: pplies to peak current. See Typical Operating Characteristics. te 5: The MX4/MX43/MX47 are put into shutdown by bringing E high and E low. If the inputs are in this state for less than 5, the parts are guaranteed not to enter shutdown. If the inputs are in this state for at least 6, the parts are guaranteed to have entered shutdown. See Low-Power Shutdown Mode section. Typical Operating Characteristics ( = 5, T = +25 C, unless otherwise noted.) OUTPUT CUENT (m) OUTPUT LOW OLTGE () OUTPUT CUENT vs. ECEIE OUTPUT LOW OLTGE OUTPUT LOW OLTGE () ECEIE OUTPUT LOW OLTGE vs. TEMPETUE TEMPETUE ( C) I = m MX4- MX OUTPUT CUENT (m) OUTPUT CUENT (m) OUTPUT CUENT vs. ECEIE OUTPUT HIGH OLTGE OUTPUT HIGH OLTGE () IE OUTPUT CUENT vs. FFEENTIL OUTPUT OLTGE FFEENTIL OUTPUT OLTGE () MX4-2 MX4-5 OUTPUT HIGH OLTGE () FFEENTIL OUTPUT OLTGE () ECEIE OUTPUT HIGH OLTGE vs. TEMPETUE TEMPETUE ( C) I = m MX IE FFEENTIL OUTPUT OLTGE vs. TEMPETUE TEMPETUE ( C) = 54Ω MX4-6 MX4/MX43/MX45/MX47 MX49/MX47 5 ownloaded from Elcodis.com electronic components distributor
6 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 Typical Operating Characteristics (continued) ( = 5, T = +25 C, unless otherwise noted.) OUTPUT CUENT (m) OUTPUT CUENT vs. IE OUTPUT LOW OLTGE OUTPUT LOW OLTGE () SUPPL CUENT (µ) MX4-7 2 OUTPUT CUENT (m) MX43/MX47 MX49 SUPPL CUENT vs. TEMPETUE MX43; E =, E = X MX47; E =, E = X MX43/MX47; E = E =, MX4/MX49; E = E = X MX43/MX47; E =, E = TEMPETUE ( C) OUTPUT CUENT vs. IE OUTPUT HIGH OLTGE OUTPUT HIGH OLTGE () MX4-2 SUPPL CUENT (µ) MX4- SUPPL CUENT (µ) 5 3 MX47 SUPPL CUENT vs. TEMPETUE MX47; E =, E = X MX47; E =, E = X MX4; E =, E = TEMPETUE ( C) TEMPETUE ( C) MX4/MX45/MX49/MX49 SUPPL CUENT vs. TEMPETUE MX4/MX45; E =, E = X MX45; E =, E = X, MX4; E = E = MX49/MX49; E = E = X MX4-3 MX4-6 ownloaded from Elcodis.com electronic components distributor
7 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers Pin escription MX4/MX43/ MX45/MX47/ MX47 P/SO TOP IEW µmx E E E PIN P/SO P/SO MX4 MX43 MX45 MX47 MX47 µmx MX4/ MX49 µmx , 7 GN Ground ninverting river Output 6 Inverting river Output 6 ninverting eceiver Input and ninverting river Output 2 2 ninverting eceiver Input 7 Inverting eceiver Input and Inverting river Output 7 Inverting eceiver Input Positive Supply: ,, 3 N.C. Connect not internally connected GN GN E MX49/ MX49 P/SO E E NME NME eceiver Output Enable. is enabled when E is low; is high impedance when E is high. river Output Enable. The driver outputs, and, are enabled by bringing E high. They are high impedance when E is low. If the driver outputs are enabled, the parts function as line drivers. While they are high impedance, they function as line receivers if E is low. river Input. low on forces output low and output high. Similarly, a high on forces output high and output low. 7 t 6 5 GN MX4 MX43 MX45 MX47 MX47 NOTE: PIN LELS N ON TIMING, TEST, N WEFOM GMS EFE TO PINS N WHEN E IS HIGH. TPICL OPETING CICUIT SHOWN WITH P/SO PCKGE. Figure. MX4/MX43/MX45/MX47/MX47 Pin Configuration and Typical Operating Circuit E E FUNCTION FUNCTION eceiver Output: If > by 2m, will be high; If < by 2m, will be low. t E E MX4/MX43/MX45/MX47 MX49/MX47 7 ownloaded from Elcodis.com electronic components distributor
8 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 TOP IEW GN P/SO MX4 MX49 µmx pplicatio Information The MX4/MX43/MX45/MX47 MX49 and MX47 are low-power traceivers for S-45 and S- 422 communicatio. The MX4, MX45, MX49, MX49, and MX47 can tramit and receive at data rates up to 2.5Mbps, while the MX43, MX47, MX4, and MX49 are specified for data rates up to 25kbps. The MX4 MX49 are full-duplex traceivers while the MX4, MX43, MX45, MX47, and MX47 are half-duplex. In addition, river Enable (E) and eceiver Enable (E) pi are included on the MX4, MX43, MX45, MX47, MX49, MX49, and MX47. When disabled, the driver and receiver outputs are high impedance GN GN Figure 2. MX4/MX49 Pin Configuration and Typical Operating Circuit TOP IEW N.C. E E GN GN P/SO ,, 3 NC E t MX4 MX49 NOTE: TPICL OPETING CICUIT SHOWN WITH P/SO PCKGE. E 4 3 6, 7 Figure 3. MX49/MX49 Pin Configuration and Typical Operating Circuit N.C. N.C. GN 9 2 t MX49 MX49 MX47/MX47: 2 Traceivers on the us The 4kΩ, / 4 -unit-load receiver input impedance of the MX47 and MX47 allows up to 2 traceivers on a bus, compared to the -unit load (2kΩ input impedance) of standard S-45 drivers (32 traceivers maximum). ny combination of MX47/ MX47 and other S-45 traceivers with a total of 32 unit loads or less can be put on the bus. The MX4/MX43/MX45 and MX4 MX49 have standard 2kΩ eceiver Input impedance. t t GN E GN E ownloaded from Elcodis.com electronic components distributor
9 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers Test Circuits O Figure 4. river C Test Load 3 E I C L FF C L2 OC Figure 6. river/eceiver Timing Test Circuit E TEST POINT ECEIE OUTPUT C L 5pF kω Figure 5. eceiver Timing Test Load OUTPUT UNE TEST C L 5Ω Figure 7. river Timing Test Load MX43/MX47/MX4/MX49: educed EMI and eflectio The MX43 and MX47 MX49 are slew-rate limited, minimizing EMI and reducing reflectio caused by improperly terminated cables. Figure 2 shows the driver output waveform and its Fourier analysis of a 5kHz signal tramitted by a MX4, MX45, MX49, MX49, or MX47. High-frequency harmonics with large amplitudes are evident. Figure 3 shows the same information displayed for a MX43, MX47, MX4, or MX49 tramitting under the same conditio. Figure 3 s high-frequency harmonics have much lower amplitudes, and the potential for EMI is significantly reduced. S S2 S S2 kω MX4/MX43/MX45/MX47 MX49/MX47 9 ownloaded from Elcodis.com electronic components distributor
10 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 Switching Waveforms FF 3 O - O O.5 /2 O t % t PLH t PHL.5 FF = () - () 9% 9% t F t SKEW = t PLH - t PHL Figure. river Propagation elays OH OL - I - I.5 t PHL INPUT OUTPUT Figure. eceiver Propagation elays t PLH.5 /2 O % 3 E, OL, 3 E OUTPUT NOMLL LOW 2.3 t L(SHN), t L t L OUTPUT NOMLL HIGH t H(SHN), t H.5.5 t H.5 OUTPUT NOMLL LOW.5 t L(SHN), t L t L OUTPUT NOMLL HIGH t H(SHN), t H t H OL +.5 OH -.5 Figure 9. river Enable and isable Times (except MX4 and MX49) OL +.5 OH -.5 Figure. eceiver Enable and isable Times (except MX4 and MX49) Function Tables (MX4/MX43/MX45/MX47/MX47) Table. Tramitting INPUTS OUTPUTS E E X X X High- X High-* X = on't care High- = High impedance * Shutdown mode for MX4/MX43/MX47 High- High-* Table 2. eceiving INPUTS OUTPUT E E - > +.2 < -.2 Inputs open X = on't care High- = High impedance * Shutdown mode for MX4/MX43/MX47 X High-* ownloaded from Elcodis.com electronic components distributor
11 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers d/div Hz 5kHz/div 5MHz Figure 2. river Output Waveform and FFT Plot of MX4/ MX45/MX49/MX49/MX47 Tramitting a 5kHz Signal Low-Power Shutdown Mode (MX4/MX43/MX47) low-power shutdown mode is initiated by bringing both E high and E low. The devices will not shut down unless both the driver and receiver are disabled. In shutdown, the devices typically draw only.µ of supply current. E and E may be driven simultaneously; the parts are guaranteed not to enter shutdown if E is high and E is low for less than 5. If the inputs are in this state for at least 6, the parts are guaranteed to enter shutdown. For the MX4, MX43, and MX47, the t H and t L enable times assume the part was not in the lowpower shutdown state (the MX45/MX4 MX49 and MX47 can not be shut down). The t H(SHN) and t L(SHN) enable times assume the parts were shut down (see Electrical Characteristics). It takes the drivers and receivers longer to become enabled from the low-power shutdown state (t H(SHN ), t L(SHN) ) than from the operating mode (t H, tl). (The parts are in operating mode if the E, E inputs equal a logical, or, or,.) d/div Hz 5kHz/div 5MHz Figure 3. river Output Waveform and FFT Plot of MX43/ MX47 MX49 Tramitting a 5kHz Signal river Output Protection Excessive output current and power dissipation caused by faults or by bus contention are prevented by two mechanisms. foldback current limit on the output stage provides immediate protection agait short circuits over the whole common-mode voltage range (see Typical Operating Characteristics). In addition, a thermal shutdown circuit forces the driver outputs into a high-impedance state if the die temperature rises excessively. Propagation elay Many digital encoding schemes depend on the difference between the driver and receiver propagation delay times. Typical propagation delays are shown in Figures 5 using Figure 4 s test circuit. The difference in receiver delay times, t PLH - tphl, is typically under 3 for the MX4, MX45, MX49, MX49, and MX47 and is typically less than for the MX43 and MX47 MX49. The driver skew times are typically 5 ( max) for the MX4, MX45, MX49, MX49, and MX47, and are typically ( max) for the MX43 and MX47 MX49. MX4/MX43/MX45/MX47 MX49/MX47 ownloaded from Elcodis.com electronic components distributor
12 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 5m/div 2/div 2/div pf TTL IN t, t F < 6 = 54Ω = 5 T = +25 C Figure 5. MX4/MX45/MX49/MX49/MX47 eceiver t PHL 5m/div 2/div 4/div = 5 T = +25 C Figure 7. MX43, MX47 MX49 eceiver t PHL pf Figure 4. eceiver Propagation elay Test Circuit 5m/div 2/div 5m/div 2/div ECEIE OUT 2/div 4/div = 5 T = +25 C Figure 6. MX4/MX45/MX49/MX49/MX47 eceiver t PLH = 5 T = +25 C Figure. MX43, MX47 MX49 eceiver t PLH 2 ownloaded from Elcodis.com electronic components distributor
13 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers Line Length vs. ata ate The S-45/S-422 standard covers line lengths up to 4 feet. For line lengths greater than 4 feet, see Figure 23. Figures 9 and 2 show the system differential voltage for the parts driving 4 feet of 26WG twisted-pair wire at khz into 2Ω loads. Typical pplicatio The MX4, MX43, MX45, MX47 MX49, and MX47 traceivers are designed for bidirectional data communicatio on multipoint bus tramission lines. - 2µs/div 5 - Figure 9. MX4/MX45/MX49/MX49/MX47 System ifferential oltage at khz riving 4ft of Cable E E MX4 MX43 MX45 MX47 MX47 2Ω 5 Figures 2 and 22 show typical network applicatio circuits. These parts can also be used as line repeaters, with cable lengths longer than 4 feet, as shown in Figure 23. To minimize reflectio, the line should be terminated at both ends in its characteristic impedance, and stub lengths off the main line should be kept as short as possible. The slew-rate-limited MX43 and MX47 MX49 are more tolerant of imperfect termination. - E E E E Figure 2. MX4/MX43/MX45/MX47/MX47 Typical Half-uplex S-45 Network 2Ω 2µs/div E E 5 - Figure 2. MX43, MX47 MX49 System ifferential oltage at khz riving 4ft of Cable 5 MX4/MX43/MX45/MX47 MX49/MX47 3 ownloaded from Elcodis.com electronic components distributor
14 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 E E 2Ω 2Ω Figure 22. MX4 MX49 Full-uplex S-45 Network E E NOTE: E N E ON MX49/MX49 ONL. E E Figure 23. Line epeater for MX4 MX49 2Ω MX4 MX49 2Ω NOTE: E N E ON MX49/MX49 ONL. T IN T OUT E E 2Ω 2Ω MX49 MX49 Isolated S-45 For isolated S-45 applicatio, see the MX253 and MX4 data sheets. E E 4 ownloaded from Elcodis.com electronic components distributor
15 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers Ordering Information (continued) PT TEMP. NGE PIN-PCKGE MX4EP -4 C to +5 C Plastic P MX4ES -4 C to +5 C SO MX4MJ -55 C to +25 C CEP MX43CP C to +7 C Plastic P MX43CS C to +7 C SO MX43CU C to +7 C µmx MX43C/ C to +7 C ice* MX43EP -4 C to +5 C Plastic P MX43ES -4 C to +5 C SO MX43MJ -55 C to +25 C CEP MX45CP C to +7 C Plastic P MX45CS C to +7 C SO MX45CU C to +7 C µmx MX45C/ C to +7 C ice* MX45EP -4 C to +5 C Plastic P MX45ES -4 C to +5 C SO MX45MJ -55 C to +25 C CEP MX47CP C to +7 C Plastic P MX47CS C to +7 C SO MX47CU C to +7 C µmx MX47C/ C to +7 C ice* MX47EP -4 C to +5 C Plastic P MX47ES -4 C to +5 C SO MX47MJ -55 C to +25 C CEP MX4CP C to +7 C Plastic P MX4CS C to +7 C SO MX4CU C to +7 C µmx MX4C/ C to +7 C ice* MX4EP -4 C to +5 C Plastic P MX4ES -4 C to +5 C SO MX4MJ -55 C to +25 C CEP MX49CP C to +7 C 4 Plastic P MX49CS C to +7 C 4 SO MX49C/ C to +7 C ice* MX49EP -4 C to +5 C 4 Plastic P MX49ES -4 C to +5 C 4 SO MX49MJ -55 C to +25 C 4 CEP Ordering Information (continued) PT MX49CP MX49CS MX49CU MX49C/ MX49EP MX49ES MX49MJ MX49CP MX49CS MX49C/ MX49EP MX49ES MX49MJ MX47CP MX47CS MX47CU MX47C/ MX47EP MX47ES MX47MJ * Contact factory for dice specificatio. Chip Topographies MX4/MX43/MX45/MX47/MX47 E E TEMP. NGE C to +7 C C to +7 C C to +7 C C to +7 C -4 C to +5 C -4 C to +5 C -55 C to +25 C C to +7 C C to +7 C C to +7 C -4 C to +5 C -4 C to +5 C -55 C to +25 C C to +7 C C to +7 C C to +7 C C to +7 C -4 C to +5 C -4 C to +5 C -55 C to +25 C GN." (2.32mm) PIN-PCKGE Plastic P SO µmx ice* Plastic P SO CEP 4 Plastic P 4 SO ice* 4 Plastic P 4 SO 4 CEP Plastic P SO µmx ice* Plastic P SO CEP N.C. N.C..54" (.372mm) MX4/MX43/MX45/MX47 MX49/MX47 5 ownloaded from Elcodis.com electronic components distributor
16 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 Chip Topographies (continued) N.C. N.C. MX4/MX49 GN." (2.32mm).54" (.372mm) E E TNSISTO COUNT: 24 SUSTTE CONNECTE TO GN MX49/MX49 GN." (2.32mm).54" (.372mm) 6 ownloaded from Elcodis.com electronic components distributor
17 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers Package Information (The package drawing(s) in this data sheet may not reflect the most current specificatio. For the latest package outline information go to N TOP IEW e FNT IEW E H C L SIE IEW - M MIN.53.4 MX.69. MIN.35. MX C e.5 SC.27 SC E H L ITIONS: M PPIET INFOMTION TITLE: INCHES INCHES PCKGE OUTLINE,.5" SOIC PPL MILLIMETES MILLIMETES MIN MX MIN MX N MS C OCUMENT CONTL NO. E. 2-4 SOICN.EPS MX4/MX43/MX45/MX47 MX49/MX47 7 ownloaded from Elcodis.com electronic components distributor
18 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specificatio. For the latest package outline information go to 2 e ÿ.5±. TOP IEW FNT IEW b E H c 4X S L OTTOM IEW SIE IEW α M PPIET INFOMTION TITLE: PCKGE OUTLINE, L umx/usop PPL MIN MX SC 2.3 b c e E H L α S INCHES SC OCUMENT CONTL NO. MILLIMETES MIN MX SC SC E J LUMX.EPS ownloaded from Elcodis.com electronic components distributor
19 Low-Power, Slew-ate-Limited S-45/S-422 Traceivers MX4/MX43/MX45/MX47 MX49/MX47 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specificatio. For the latest package outline information go to Maxim cannot assume respoibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. circuit patent licees are implied. Maxim reserves the right to change the circuitry and specificatio without notice at any time. Maxim Integrated Products, 2 San Gabriel rive, Sunnyvale, C PPN.EPS MX4/MX43/MX45/MX47 MX49 23 Maxim Integrated Products Printed US is a registered trademark of Maxim Integrated Products. ownloaded from Elcodis.com electronic components distributor
RECEIVER/ DRIVER ENABLE LOW-POWER SHUTDOWN. Yes Yes Yes Yes No Yes No Yes Yes. Yes Yes No Yes No No No No No
9-; ev ; /96 Low-Power, Slew-ate-Limited S-4/S-4 Traceivers General escription The MX4, MX43, MX4, MX47 MX49, and MX47 are low-power traceivers for S-4 and S- 4 communication. Each part contai one driver
More informationSelection Table RECEIVER/ DRIVER ENABLE LOW-POWER SHUTDOWN. Yes Yes No Yes No No No No No. Yes Yes Yes Yes No Yes No Yes Yes
9-22; ev ; /3 General escription The MX4, MX43, MX45, MX47 MX49, and MX47 are low-power traceivers for S-45 and S- 422 communication. Each part contai one driver and one receiver. The MX43, MX47, MX4,
More informationLow-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers
ILLE MX48/MX483/MX48/ MX487 MX49/MX487 Low-Power, Slew-ate-Limited S-48/S-4 Traceivers General escription The MX48, MX483, MX48, MX487 MX49, and MX487 are low-power traceivers for S-48 and S- 4 communication.
More informationMAX481/MAX483/MAX485/ MAX487 MAX491/MAX1487. Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers. Benefits and Features. General Description
MX481/MX483/MX485/ MX487 MX491/MX1487 Low-Power, Slew-ate-Limited S-485/S-422 Transceivers General escription The MX481, MX483, MX485, MX487 MX491, and MX1487 are low-power transceivers for S-485 and S-422
More informationMAX1481/MAX1484/MAX1485/MAX1486
9-2; ev ; /06 Software-Selectable, Half-/Full-uplex, Slew-ate-Limited, 2Mbps, S-85/S-22 Traceivers in µmx Package General escription The provide software-selectable, half-/full-duplex, low-power, slewrate-limited,
More information±15kV ESD-Protected, Slew-Rate-Limited, Low-Power, RS-485/RS-422 Transceivers
9-4; ev 3; 7/96 ±5kV ES-Protected, Slew-ate-Limited, Low-Power, S-485/S-422 Traceivers General escription The MX48E, MX483E, MX485E, MX487E MX49E, Features ES Protection: ±5kV Human ody Model and MX487E
More informationRS-485/RS-422 Transceivers with Preemphasis for High-Speed, Long-Distance Communication
19-145; ev 1; 4/99 S-485/S-422 Traceivers with Preemphasis General escription The high-speed S-485/S-422 traceivers feature driver preemphasis circuitry, which extends the distance and increases the data
More informationMAX485 Low Power, Slew-Rate-Limited RS-485/RS-422 Transceiver
MX485 Low Power, Slew-ate-Limited S-485/S-422 Transceiver DESCIPTION The MX485 is low-power transceivers for S-485 and S-422 communication. IC contains one driver and one receiver. The driver slew rates
More information±80V Fault-Protected, Fail-Safe, 1/4-Unit Load, +3.3V RS-485 Transceiver
9-2756; ev ; 4/3 ±8V Fault-Protected, Fail-Safe, General escription The MX343 fault-protected S-485 transceiver features ±8V protection from overvoltage signal faults on communication bus lines. Each device
More information+3.3V, ±15kV ESD-Protected, Fail-Safe, Hot-Swap, RS-485/RS-422 Transceivers
19-2668; ev 2; 4/9 +3.3V, ±15kV ES-Protected, Fail-Safe, General escription The 3.3V, ±15kV ES-protected, S-485/S-422 transceivers feature one driver and one receiver. These devices include fail-safe circuitry,
More information3.3V Slew Rate Limited, Half and Full Duplex ADM3483/ADM3485/ADM3488/ADM3490
Preliminary Technical ata 3.3V Slew ate Limited, Half and Full uplex M3483/M3485/M3488/M3490 FETUES EI S-485/S-422 Compliant ata ate Options M3483, M3488 250kbps M3485, M3490 10Mbps Half and Full uplex
More informationMAX485. Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceiver PIN CONFIGURATION
Low-Power, Slew-Rate-Limited RS-8/RS- Traceiver SRIPTION The MX8 is low-power traceivers for RS-8 and RS- communication. The I contai one driver and one receiver. The driver slew rates of the MX8 is not
More informationADM488A/ADM489A. Full-Duplex, Low Power, Slew Rate Limited, EIA RS-485 Transceivers FUNCTIONAL BLOCK DIAGRAMS FEATURES APPLICATIONS
Full-uplex, Low Power, Slew ate Limited, EI S-485 Transceivers M488/M489 FETUES Complies with NSI TI/EI-485--1998 and ISO 8482: 1987(E) 250 kbps data rate Single 5 V ± 10% supply 7 V to +12 V bus common-mode
More information±15kV ESD-Protected, 10Mbps, 3V/5V, Quad RS-422/RS-485 Receivers
19-498; Rev 1; 1/ ±15k ESD-Protected, 1Mbps, 3/5, eneral Description The are rugged, low-power, quad, RS-422/RS-485 receivers with electrostatic discharge (ESD) protection for use in harsh environments.
More informationTOP VIEW. Maxim Integrated Products 1
19-2648; Rev 0; 10/02 EALUATION KIT AAILABLE 1:5 ifferential (L)PECL/(L)ECL/ General escription The is a low-skew, 1-to-5 differential driver designed for clock and data distribution. This device allows
More informationISOV CC A B Y Z YR C1HI C2LO C2HI ISOCOM ±50V. C4 10nF. Maxim Integrated Products 1
19-1778; Rev 3; 11/1 High CMRR RS-485 Transceiver with ±5V Isolation General Description The is a high CMRR RS-485/RS-422 data-communications interface providing ±5V isolation in a hybrid microcircuit.
More informationISL8483, ISL8485, ISL8488, ISL8489, ISL8490, ISL8491
ISL88, ISL88, ISL888, ISL889, ISL89, ISL89 ata Sheet February 8, 6 FN66.8 V, Low Power, High Speed or Slew ate Limited, S-8/S- Transceivers The Intersil S-8/S- devices are icmos V powered, single transceivers
More informationDATASHEET ISL8488E, ISL8489E, ISL8490E, ISL8491E. Features. Applications
TSHEET ISL888E, ISL889E, ISL89E, ISL89E ±kv ES Protected, V, Low Power, High Speed and Slew ate Limited, Full uplex, S-8/S- Transceivers FN67 ev.. July 6, 7 The ISL888E, ISL889E, ISL89E, ISL89E devices
More informationILX485. Low-Power, RS-485/RS-422 Transceivers TECHNICAL DATA
TECHNICAL DATA Low-Power, RS-485/RS-422 Transceivers ILX485 Description The ILX485 is low-power transceivers for RS-485 and RS- 422 communication. IC contains one driver and one receiver. The driver slew
More information+5 V Low Power EIA RS-485 Transceiver ADM1485
a FETUES Meets EI S-8 Standard 3 Mb/s Data ate Single + V Supply 7 V to +12 V us Common-Mode ange High Speed, Low Power icmos Thermal Shutdown Protection Short Circuit Protection Zero Skew Driver Driver
More informationPART MAX3183. MAX3181EUK-T -40 C to +85 C 5 SOT23-5 ADKG MAX3182EUK-T -40 C to +85 C 5 SOT23-5 ADKH MAX3183EUK-T -40 C to +85 C 5 SOT23-5 ADKI
19-1444; Rev 1; 7/99 +3 to +5.5, 1.5Mbps General Description The MAX318MAX3183 are single RS-232 receivers in a SOT23-5 package for space- and cost-cotrained applicatio requiring minimal RS-232 communicatio.
More informationSP3493/SP V Low Power RS-485/RS-422 Transceivers. Now Available in Lead-Free Packaging
SP3493/SP3494 Operates From A Single +3. Supply Interoperable With +5V Logic +00mV eceiver Input Sensitivity -7V to +1V Common-Mode Input Voltage ange evices Allow Up To 3 Transceivers On The Serial Bus
More informationHigh-Speed, 3V/5V, Rail-to-Rail, Single-Supply Comparators MAX961/MAX962
19-119; Rev 0; 9/96 High-Speed, 3/, Rail-to-Rail, General Description The are high-speed, single/dual comparators with internal hysteresis. These devices are optimized for single +3 or + operation. The
More information±80V Fault-Protected, 2Mbps, Low Supply Current CAN Transceiver
19-2425; Rev 0; 4/02 General Description The interfaces between the control area network (CAN) protocol controller and the physical wires of the bus lines in a CAN. It is primarily intended for industrial
More information5 V Low Power EIA RS-485 Transceiver ADM1485
a FETUES Meets EI S-485 Standard 3 Mbps Data ate Single 5 V Supply 7 V to +12 V us Common-Mode ange High Speed, Low Power icmos Thermal Shutdown Protection Short-Circuit Protection Driver Propagation Delay:
More information±15kV ESD Protected, 3.3V, Full Fail-safe, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers. Features
TSHEET ISL87E/71E/7E/7E/7E/76E/77E/78E ±1kV ES Protected,.V, Full Fail-safe, Low Power, High Speed or Slew ate Limited, S-8/S- Transceivers FN611 ev. October, 1 The Intersil ISL87XE are icmos.v powered,
More information5 V Low Power EIA RS-485 Transceiver ADM485
a FETUES Meets EI S-485 Standard 5 Mbps Data ate Single 5 V Supply 7 V to +12 V us Common-Mode ange High Speed, Low Power icmos Thermal Shutdown Protection Short-Circuit Protection Driver Propagation Delay:
More information3.3 V Slew Rate Limited, Half Duplex RS-485/RS-422 Transceiver ADM3493
3.3 V Slew ate Limited, Half uplex S-485/S-422 Transceiver M3493 FETUES Operates with 3.3 V supply Interoperable with 5 V logic EI S-422 and S-485 compliant over full CM range ata rate: 25 kbps Half duplex
More informationFeatures RECEIVER/DRIVER ENABLE?
TSHEET ISL88, ISL88, ISL888, ISL89, ISL89.V, Low Power, High Speed or Slew ate Limited, S-8/S- Transceivers FN6 ev. These Intersil S-8/S- devices are icmos.v powered, single transceivers that meet both
More information3V to 5.5V-Powered, ±15kV ESD-Protected, Slew-Rate-Limited, True RS-485 Transceivers UM3483E/UM3486E SOP8/DIP8. Features
3V to 5.5V-Powered, ±15kV ES-Protected, Slew-Rate-Limited, True RS-485 Transceivers UM3483E/UM3486E SOP8/IP8 General escription The UM3483E, UM3486E are 3V to 5.5V-powered, ±15kV ES-protected, slew-rate-limited
More informationISL83070E, ISL83071E, ISL83072E, ISL83073E, ISL83075E, ISL83076E, ISL83077E, ISL83078E
ISL87E, ISL87E, ISL87E, ISL87E, ISL87E, ISL876E, ISL877E, ISL878E ata Sheet June, 7 FN6. ±kv ES Protected,.V, Full Fail-safe, Low Power, High Speed or Slew ate Limited, S-8/S- Transceivers The Intersil
More informationLow-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers
' Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers SCRIPTION The is low-power transceivers for RS-485 and RS-422 communication. IC contains one driver and one receiver. The driver slew rates of
More informationPART TOP VIEW TXD V CC. Maxim Integrated Products 1
9-2939; Rev ; 9/3 5V, Mbps, Low Supply Current General Description The interface between the controller area network (CAN) protocol controller and the physical wires of the bus lines in a CAN. They are
More information5 V Slew-Rate Limited Half- and Full-Duplex RS-485/RS-422 Transceivers ADM4850 ADM4857
5 V Slew-ate Limited Half- and Full-Duplex S-485/S-422 Transceivers DM4850 DM4857 FETUES EI S-485-/S-422-compliant Data rate options DM4850/DM4854 115 kbps DM4851/DM4855 500 kbps DM4852/DM4856 2.5 Mbps
More informationLTC485 Low Power RS485 Interface Transceiver Features
Low Power S485 Interface Transceiver Features n Low Power: I CC = 3μ Typ n Designed for S485 Interface pplications n Single 5V supply n 7V to 12V us Common Mode ange Permits ±7V Ground Difference etween
More informationPART N.C. 1 8 V CC V BB 4. Maxim Integrated Products 1
19-2152; Rev 2; 11/02 ifferential LPECL/LECL/HSTL Receiver/rivers General escription The are low-skew differential receiver/drivers designed for clock and data distribution. The differential input can
More informationDATASHEET ISL8483, ISL8485, ISL8488, ISL8489, ISL8490, ISL8491. Features. Applications
TSHEET ISL88, ISL88, ISL888, ISL889, ISL89, ISL89 V, Low Power, High Speed or Slew ate Limited, S-8/S- Transceivers FN66 ev 9. The Intersil S-8/S- devices are icmos V powered, single transceivers that
More information3.3 V Slew Rate Limited, Half- and Full-Duplex, RS-485/RS-422 Transceivers ADM3483/ADM3485/ADM3488/ADM3490/ADM3491
3.3 V Slew ate Limited, Half- and Full-uplex, S-485/S-422 Transceivers M3483/M3485/M3488/M349/M3491 FETUES Operate with 3.3 V supply Interoperable with 5 V logic EI S-422 and S-485 compliant over full
More information50mA, Frequency-Selectable, Switched-Capacitor Voltage Converters
9-39; Rev ; /3 General escription The charge-pump voltage converters invert input voltages ranging from +.5V to +5.5V, or double input voltages ranging from +.5V to +5.5V. Because of their high switching
More informationSP490E / SP491E. Enhanced Full-Duplex RS-485 Transceivers. Description. Block Diagrams VCC NC A B A B RE DE 10 Z D GND Y GND GND
Enhanced Full-uplex S-485 Transceivers escription The SP490E is a low power differential line driver/receiver meeting S-485 and S-422 standards up to 10Mbps. The SP491E is identical to the SP490E with
More information±15kV ESD-Protected, ±60V Fault-Protected, 10Mbps, Fail-Safe RS-485/J1708 Transceivers
MX344E MX3444E ±15kV ES-Protected, ±6V Fault-Protected, 1Mbps, Fail-Safe S-485/J178 Transceivers General escription The MX344E MX3444E fault-protected S-485 and J178 transceivers feature ±6V protection
More informationSP V Low Power RS-485/RS-422 Transceiver RO 1 VCC RE 2 DE 3 DI 4 GND. Description. Block Diagram
3. Low Power S-485/S-4 Transceiver escription The SP3494 device is a 3. low power half-duplex transceiver that meets the specifications of the S-485 and S-4 serial protocols. This device is pin-to-pin
More informationSP V Low Power Half-Duplex RS-485 Transceiver with 10Mbps Data Rate RO 1 V CC RE 2 DE 3 DI 4 GND. Description.
3. Low Power Half-uplex S-485 Transceiver with 10Mbps ata ate escription The SP3485 device is a 3. low power half-duplex transceiver that meets the specifications of the S-485 and S-422 serial protocols.
More information±15kV ESD-Protected, Isolated, 3.3V RS-485/RS-422 Data Interfaces
19-1941; Rev 1; 3/6 ±15kV ES-Protected, Isolated, 3.3V General escription The MX348E/MX348E are electrically isolated RS-485/RS-4 data-communications interfaces. The RS-485/RS-4 I/O pins are protected
More information±15kV ESD-Protected, 1Mbps, 1µA RS-232 Transmitters in SOT23-6
19-164; Rev 1; 3/ ±15k ESD-Protected, bps, 1 General Description The / single RS-3 transmitters in a SOT3-6 package are for space- and cost-constrained applications requiring minimal RS-3 communications.
More informationNot Recommended for New Designs
Not Recommended for New Designs This product was manufactured for Maxim by an outside wafer foundry using a process that is no longer available. It is not recommended for new designs. The data sheet remains
More informationMAX13442E/MAX13443E/ MAX13444E. ±15kV ESD-Protected, ±80V Fault-Protected, Fail-Safe RS-485/J1708 Transceivers
MX13442E/MX13443E/ General escription The MX13442E/ are fault-protected S-485 and J178 transceivers that feature ±8V protection from signal faults on communication bus lines. The MX13442E/ feature a reduced
More informationSP V Low Power Slew Rate Limited Half-Duplex RS-485 Transceiver SP Pin nsoic. Now Available in Lead Free Packaging
SP3483 S-485 and S-4 Transceiver Operates from a single +3. supply Interoperale with +5. logic river/eceiver nale Low Power Shutdown Mode -7V to +1V Common-Mode Input Voltage ange llows up to 3 transceivers
More informationCurrent-Limited Switch for Two USB Ports
9-2385; Rev 2; /2 Current-Limited Switch for Two USB Ports General escription The MAX93 current-limited 7mΩ switch with built-in fault blanking provides an accurate, preset.2a to 2.3A current limit, making
More informationECL/PECL Dual Differential 2:1 Multiplexer
19-2484; Rev 0; 7/02 ECL/PECL Dual Differential 2:1 Multiplexer General Description The fully differential dual 2:1 multiplexer (mux) features extremely low propagation delay (560ps max) and output-to-output
More information±15kV ESD-Protected, EMC-Compliant, 230kbps RS-232 Serial Port for Modems
19-177; Rev ; 9/96 ±15k ES-Protected, EMC-Compliant, 23kbps General escription The is a complete CE RS-232 serial port designed to meet the stringent ES requirements of the European community. All transmitter
More informationTOP VIEW MAX9111 MAX9111
19-1815; Rev 1; 3/09 EVALUATION KIT AVAILABLE Low-Jitter, 10-Port LVDS Repeater General Description The low-jitter, 10-port, low-voltage differential signaling (LVDS) repeater is designed for applications
More informationCARD 1 CARD 15 CARD 16. Maxim Integrated Products 1
19-2287; Rev 0; 1/02 Quad Bus LVDS Traceiver General Description The is a quad bus LVDS (BLVDS) traceiver for heavily loaded, half-duplex multipoint buses. Small 32-pin QFN and TQFP packages and flow-through
More informationDS3695/DS3695T/DS3696/DS3697 Multipoint RS485/RS422 Transceivers/Repeaters
DS3695/DS3695T/DS3696/DS3697 Multipoint RS485/RS422 Transceivers/Repeaters General Description The DS3695, DS3696, and DS3697 are high speed differential TRI-STATE bus/line transceivers/repeaters designed
More informationIsolated RS485 Interface. Features 2500 V RMS. Applications. Description
NVE COPOATION IL485ISOLOOP Isolated S485 Interface Functional iagram Features GALVANIC ISOLATION ISO A B 2500 V MS Isolation (1 min) 25 ns Maximum Propagation elay 35 MBaud ata ate 1 ns Skew esigned for
More information±15kV ESD-Protected, EMC-Compliant, 230kbps RS-232 Serial Port for Motherboards/Desktop PCs
19-176; Rev ; 9/96 ±k ES-Protected, EMC-Compliant, 23kbps RS-232 Serial Port for Motherboards/esktop PCs General escription The is a complete TE RS-232 serial port designed to meet the stringent ES requirements
More informationCLK_EN CLK_SEL. Q3 THIN QFN-EP** (4mm x 4mm) Maxim Integrated Products 1
19-2575; Rev 0; 10/02 One-to-Four LVCMOS-to-LVPECL General Description The low-skew, low-jitter, clock and data driver distributes one of two single-ended LVCMOS inputs to four differential LVPECL outputs.
More information±80V Fault-Protected, 2Mbps, Low Supply Current CAN Transceiver
General Description The MAX3053 interfaces between the control area network (CAN) protocol controller and the physical wires of the bus lines in a CAN. It is primarily intended for industrial systems requiring
More informationCurrent-Limited Switch for Single USB Port
9-57; Rev ; / Current-Limited Switch for Single USB Port General Description The is a current-limited, 6mΩ switch with built-in fault blanking. Its accurate preset current limit of.6a to.6a makes it ideally
More informationPART MXD1013C/D MXD1013PD MXD1013UA MXD1013SE PART NUMBER EXTENSION (MXD1013 )
19-094; Rev 0; /97 -in-1 Silicon Delay Line General Description The contai three independent, monolithic, logic-buffered delay lines with delays ranging from 10 to 200. Nominal accuracy is ±2 for a 10
More informationV6601 RS-485 Transceiver
V6601 RS-485 Transceiver Version: 0.3 Release Date: January 19, 2018 Specifications are subject to change without notice. 2016 This document contains information that is proprietary to Unauthorized reproduction
More informationSP V Low Power Slew Rate Limited Half-Duplex RS-485 Transceiver
SP3483 +3. Low Power Slew Rate Limited Half-uplex RS-485 Transceiver RS-485 and RS-4 Transceiver Operates from a single +3. Supply Interoperable with +5. logic river/receiver Enable Low Power Shutdown
More informationIsolated RS485 Interface With Handshake. Features 2500 V RMS. Applications. Description
NVE COPOTION IL485WISOLOOP Isolated S485 Interface With Handshake Functional iagram E GLVNIC ISOLTION ISO OUT 1 Features 2500 V MS Isolation (1 min) 25 ns Maximum Propagation elay 35 Maud ata ate 1 ns
More informationON SWITCH NONE COM-NO0 COM-NO1 COM-NO2 COM-NO3 ADDA ADDB X = DON T CARE N.C. = NO CONNECT
9-224; Rev ; /8 Low-Voltage, 6, 4: Analog Multiplexer in QFN General Description The MAX474 low-voltage, 4-channel analog multiplexer operates from a single +.8V to +.V supply. The MAX474 features break-before-make
More informationSingle/Dual LVDS Line Receivers with Ultra-Low Pulse Skew in SOT23
19-1803; Rev 3; 3/09 Single/Dual LVDS Line Receivers with General Description The single/dual low-voltage differential signaling (LVDS) receivers are designed for highspeed applications requiring minimum
More informationPrecision, 8-Channel/Dual 4-Channel, Low-Voltage, CMOS Analog Multiplexers
9-299; Rev. 6; 6/7 Precision, 8-Channel/Dual 4-Channel, General Description The precision, monolithic, CMOS analog multiplexers (muxes) offer low on-resistance (less than Ω), which is matched to within
More informationSingle LVDS/Anything-to-LVPECL Translator
9-2808; Rev 0; 4/03 Single LVDS/Anything-to-LVPECL Translator General Description The is a fully differential, high-speed, anything-to-lvpecl translator designed for signal rates up to 2GHz. The s extremely
More information±15kV ESD-Protected 52Mbps, 3V to 5.5V, SOT23 RS-485/RS-422 True Fail-Safe Receivers
19-3; Rev 1; 3/11 ±1kV ESD-Protected Mbps, 3V to.v, SOT3 General Description The MAX38E/MAX381E/MAX383E/MAX384E are single receivers designed for RS-48 and RS-4 communication. These devices guarantee data
More informationSP3490 / SP V Low Power Full-Duplex RS-485 Transceivers with 10Mbps Data Rate VCC 13 NC 12 2 A B A B REB DE 10 Z 5 D GND GND GND.
3.3V Low Power Full-uplex S-485 Transceivers with 10Mbps ata ate escription The SP3490 and SP3491 devices are 3.3V low power full-duplex transceivers that meet the specifications of the S-485 and S-4 serial
More information6500V/µs, Wideband, High-Output-Current, Single- Ended-to-Differential Line Drivers with Enable
99 Rev ; /99 EVALUATION KIT AVAILABLE 65V/µs, Wideband, High-Output-Current, Single- General Description The // single-ended-todifferential line drivers are designed for high-speed communications. Using
More informationHigh-Precision, Low-Voltage, Micropower Op Amp MAX480. General Description. Features. Ordering Information. Applications.
9-77; Rev a; /98 High-Precision, Low-oltage, General Description The is a precision micropower operational amplifier with flexible power-supply capability. Its guaranteed µ maximum offset voltage (5µ typ)
More informationADM1487. Preliminary Technical Data. PRELIMINARY TECHNICAL DATA Ultra-Low Power RS-485/RS-422 Transceiver with Low EMI and +/-10kV ESD Protection
a PELIMINY TECHNICL DT Ultra-Low Power S-/S-22 Transceiver with Low EMI and +/-0kV ESD Protection Preliminary Technical Data DM7 FETUES Low Power - 20µ Max ICC with Driver Disabled High Input Impedance
More informationDS485 Low Power RS-485/RS-422 Multipoint Transceiver
DS485 Low Power RS-485/RS-422 Multipoint Transceiver General Description The DS485 is a low-power transceiver for RS-485 and RS-422 communication. The device contains one driver and one receiver. The drivers
More informationILX485 Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers
Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceivers General Description The ILX485 is low-power transceivers for RS-485 and RS- 422 communication. I contains one driver and one receiver. The driver
More informationSP1490E/SP1491E. Full Duplex RS-485 Transceivers SP1491E. 8 Pin - nsoic. description
SP49E/SP49E Full Duplex S-485 Transceivers features +5V Only Low Power icmos Driver/eceiver Enable (SP49E) S-485 and S-422 Drivers/eceivers Pin Compatible with SN7579 (SP49E) Pin Compatible with SN758
More information±15kV ESD-Protected, 3.0V to 5.5V, Low-Power, up to 250kbps, True RS-232 Transceiver
19-1949; Rev ; 1/1 ±15k ESD-Protected, 3. to 5.5, Low-Power, General Description The is a 3-powered EIA/TIA-232 and.28/.24 communications interface with low power requirements, high data-rate capabilities,
More informationNot Recommended for New Designs
Not Recommended for New Designs The MAX99 was manufactured for Maxim by an outside wafer foundry using a process that is no longer available. It is not recommended for new designs. A Maxim replacement
More informationTOP VIEW. Maxim Integrated Products 1
19-2213; Rev 0; 10/01 Low-Jitter, Low-Noise LVDS General Description The is a low-voltage differential signaling (LVDS) repeater, which accepts a single LVDS input and duplicates the signal at a single
More information±50V Isolated, 3.0V to 5.5V, 250kbps, 2 Tx/2 Rx, RS-232 Transceiver MAX3250
EVALUATION KIT AVAILABLE MAX325 General Description The MAX325 is a 3.V to 5.5V powered, ±5V isolated EIA/TIA-232 and V.28/V.24 communications interface with high data-rate capabilities. The MAX325 is
More information300MHz, Low-Power, High-Output-Current, Differential Line Driver
9-; Rev ; /9 EVALUATION KIT AVAILABLE 3MHz, Low-Power, General Description The differential line driver offers high-speed performance while consuming only mw of power. Its amplifier has fully symmetrical
More informationOUTPUT UP TO 300mA C2 TOP VIEW FAULT- DETECT OUTPUT. Maxim Integrated Products 1
19-1422; Rev 2; 1/1 Low-Dropout, 3mA General Description The MAX886 low-noise, low-dropout linear regulator operates from a 2.5 to 6.5 input and is guaranteed to deliver 3mA. Typical output noise for this
More informationST485 LOW POWER RS-485/RS-422 TRANSCEIVER
LOW POWER RS-485/RS-422 TRANSCEIVER LOW QUIESCENT CURRENT: 300µA DESIGNED FOR RS-485 INTERFACE APPLICATIONS -7V TO 12V COMMON MODE INPUT VOLTAGE RANGE DRIVER MAINTAINS HIGH IMPEDANCE IN 3-STATE OR WITH
More informationLVDS/Anything-to-LVPECL/LVDS Dual Translator
19-2809; Rev 1; 10/09 LVDS/Anything-to-LVPECL/LVDS Dual Translator General Description The is a fully differential, high-speed, LVDS/anything-to-LVPECL/LVDS dual translator designed for signal rates up
More informationDS485 Low Power RS-485/RS-422 Multipoint Transceiver
Low Power RS-485/RS-422 Multipoint Transceiver General Description The DS485 is a low-power transceiver for RS-485 and RS- 422 communication. The device contains one driver and one receiver. The drivers
More informationSingle/Dual LVDS Line Receivers with In-Path Fail-Safe
9-2578; Rev 2; 6/07 Single/Dual LVDS Line Receivers with General Description The single/dual low-voltage differential signaling (LVDS) receivers are designed for high-speed applications requiring minimum
More informationLow-Cost, Micropower, High-Side Current-Sense Amplifier + Comparator + Reference ICs
9-63; Rev ; /3 Low-Cost, Micropower, High-Side Current-Sense General Description The low-cost, micropower, high-side current-sense supervisors contain a highside current-sense amplifier, bandgap reference,
More information800Mbps LVDS/LVPECL-to-LVDS 2 x 2 Crosspoint Switch
19-2003; Rev 0; 4/01 General Description The 2 x 2 crosspoint switch is designed for applications requiring high speed, low power, and lownoise signal distribution. This device includes two LVDS/LVPECL
More informationV6602H RS-485 Transceiver
V6602H RS-485 Transceiver Version: 0.5 Release Date: October 22, 2017 Specifications are subject to change without notice. 2016 This document contains information that is proprietary to Unauthorized reproduction
More information5 V Low Power EIA RS-485 Transceiver ADM1485
a FETUES Meets EI S-485 Standard 3 Mbps Data ate Single 5 V Supply 7 V to +12 V us Common-Mode ange High Speed, Low Power icmos Thermal Shutdown Protection Short-Circuit Protection Driver Propagation Delay:
More informationISL Features. 3.3V, Low Power, 30Mbps, RS-485/RS-422 Transceiver. Applications. Pinout. Ordering Information FN Data Sheet March 15, 2005
ISL448 ata Sheet FN67..V, Low Power, Mbps, RS-48/RS-4 Transceiver The Intersil ISL448 is a high speed BiCMOS.V powered, single transceiver that meets both the RS-48 and RS-4 standards for balanced communication.
More informationFeatures TABLE 1. SUMMARY OF FEATURES. RS-232 DATA RATE (kbps) RS-485 DATA RATE (bps) ISL Ld QFN (6mmx6mm) 20M, 460k, 115k 650 YES BOTH YES
TSHEET ISL887, ISL87 ±kv ES Protected, V, ual Protocol (S-22/S-8) Transceivers FN62 ev. June 9, 2 These devices are icmos interface ICs that are user configured as either a single S-22, S-8 differential
More informationINTEGRATED CIRCUITS. 74LVC V Parallel printer interface transceiver/buffer. Product specification 1995 Nov 10 IC24 Low Voltage Handbook
INTEGRTED CIRCUITS 3.3V Parallel printer interface traceiver/buffer 1995 Nov 10 IC4 Low Voltage Handbook FETURES synchronous operation 4-Bit traceivers 3 additional buffer/driver lines TTL compatible inputs
More informationComplete, Isolated RS-485/RS-422 Data Interface MAX1480A/B/C/MAX1490A/B
9-259; Rev 5; 5/5 Complete, Isolated RS-485/RS-422 General Description The MX48/MX48/MX48C/MX49/ MX49 are complete, electrically isolated, RS-485/ RS-422 data-communications interface solutions in a hybrid
More information5 V, Slew-Rate Limited, Half-Duplex and Full-Duplex RS-485/RS-422 Transceivers
5 V, Slew-ate Limited, Half-Duplex and Full-Duplex S-485/S-422 Transceivers DM4850/DM485/DM4852/DM4853/DM4854/DM4855/DM4856/DM4857 FETUES EI S-485-/S-422-compliant Data rate options DM4850/DM4854: 5 kbps
More informationData Sheet April 22, Features HOT PLUG?
ISL179E, ISL18E ata Sheet pril, 8 FN66. High ES Protected, +1 C, Mbps,.V, Full Fail-Safe, S-8/S- Transceivers Intersil s ISL179E and ISL18E are high ES Protected (see Table 1 below),.v powered, single
More informationHigh-Speed, Low-Voltage, 4Ω, Dual SPST CMOS Analog Switches
9-; Rev ; / High-Speed, Low-oltage, Ω, Dual SPST General Description The MAX//MAX are monolithic, dual, single-pole/single-throw (SPST) switches that can operate from a single supply ranging from +. to
More informationPrecision, Low-Power, 6-Pin SOT23 Temperature Sensors and Voltage References
19-2457; Rev 2; 11/03 Precision, Low-Power, 6-Pin SOT23 General Description The are precise, low-power analog temperature sensors combined with a precision voltage reference. They are ideal for applications
More informationLVTTL/LVCMOS DATA INPUT 100Ω SHIELDED TWISTED CABLE OR MICROSTRIP PC BOARD TRACES. Maxim Integrated Products 1
19-1991; Rev ; 4/1 EVALUATION KIT AVAILABLE General Description The quad low-voltage differential signaling (LVDS) line driver is ideal for applications requiring high data rates, low power, and low noise.
More informationLow-Noise, Precision, +2.5V/+4.096V/+5V Voltage Reference
19-193; Rev ; 4/1 Low-Noise, Precision, +2.5V/+4.96V/+5V General Description The is a low-noise, precision voltage reference with extremely low 2ppm/ C temperature coefficient over the automotive temperature
More informationSingle/Dual/Quad High-Speed, Ultra Low-Power, Single-Supply TTL Comparators
19-129; Rev. 3; 7/94 Single/Dual/Quad High-Speed, Ultra Low-Power, General Description The MAX97/MAX98/MAX99 dual, quad, and single high-speed, ultra low-power voltage comparators are designed for use
More information