The DIY Lantern Blind Wiring Diagrams & Programming Instructions

Transcription

1 The DIY Lantern Blind Wiring Diagrams & Programming Instructions

2 The DIY Lantern Blind Wiring Diagrams

3 motor which may be mounted either on the RH or LH side 2-core motor flex Standard configuration Somfy RF Radio ontrolled Motor with either Remote ontrol or Smoove battery operated wall switch NOTES Max length of motor flex is 2.5m Radio Remote Switch standard 13A 1.5mm² single phase supply 2-core motor flex PROJET TITLE E DRAWING TITLE Simplified schematic wiring diagram for radio blinds DRAWING NO. connection of motor flex to mains power (e.g. 'Klix' socket, spur unit, etc.) Diagram based on using Somfy motors DRAWN BY SALE N.T.S DATE

4 Radio controlled wiring diagram for multiple blinds *IMPORTANT!!! One of the motors must be able to be isolated so it can be worked on individually ( necessary for set up & testing ) Standard configuration Somfy RF Radio ontrolled Motor with either Remote ontrol or Smoove battery operated wall switch 24v 13A Supply onnector Block onnector Block onnector Block onnector Block onnector Block Motor Motor Motor Motor Motor Motor

5 motor which may be mounted either on the RH or LH side 3-core motor flex onfiguration for hard wired Somfy Motor with 3 position latching rocker switch. NOTES Max length of motor flex is 2.5m connection of motor flex to switch wire (e.g. 'Klix' socket, spur unit, etc.) N.B. This wiring arrangement is only for one motor with one switch. Additional motors from one switch MUST be wired via a relay. standard 13A 1.5mm² single phase supply 3-core switch wire switch DRAWING TITLE Simplified schematic wiring diagram for hardwired blinds DRAWING NO. DRAWN BY DATE 3 postion latching rocker switch Diagram based on using Somfy motors SALE N.T.S

6 WT ( Wired Technology ) wiring diagram for multiple blinds ( with relay ) motor which may be mounted either on the RH or LH side core motor flex onfiguration for hard wired Somfy Motor with 3 position latching rocker switch for multiple blinds. IMPORTANT NOTES Std length of motor flex is 2.5m N.B. To operate more than one motor from one switch they MUST be wired via a relay. 3 postion latching Direction 1 Direction 2 ommon When motors are wired to the relay box, they must be wired to individual outputs per motor only. Only one motor must be wired to one output. standard 13A 1.5mm² single phase supply Relay Box If more than one motor is wired to one output it will damage the relay box and motor. Diagram based on using Somfy motors DRAWING TITLE Simplified schematic wiring diagram for hardwired blinds

7 The DIY Lantern Blind RF Remote ontrol Programming Instructions

8 RTS Motors - programming and Basic setting Basic 1 onnect the RTS transmitter to the motor Only connect the motor that should be programmed to power When programming a multi channel control, choose channel first Press simultaneously until... 2 heck the motor rotation direction OK 4 NOT OK 3... motor jogs. 3 hange motor rotation direction if needed 2sec. Q -o Press until......motor jogs. 4 Place the blind in the desired UP position For Sonesse 3 RTS If the motor doesn't react, reverse the cables in the power supply. Start programming again. L : - '-" "O N cc g I?"> r N (f) a D D '-" (f) a D,,_ (f) a D D ---, 5 Set the UP position ;; ) o./;; ) Short Simultaneous press Blind goes down Stop at desired down position Adjust if needed

9 RTS Motors - programming and Basic setting Basic 6 Set the DOWN position.,.,.,., g:j <fl Short simultaneous press The motor moves upwards and stops at the UP position 7 onfirm end limit setting <fl ('"J <fl 2sec. Press until motor jogs 8 Recording an RTS transmitter 4 :.:J c.-<l c5 Press the prog button... motor jogs a:: on the back of the control until... ('"J 6 c -,

10 RTS Motors - programming and Basic setting Basic 1 Adjusting the DOWN limit 2 ii Place the blind in the down position Press simultaneously... motor jogs ) ) /s) ' cc/ e hoose a new down position 1 Adjusting the UP limit 2 Place the blind in the up position /'R) ---"Ye cl:'! hoose a new up position until... 2sec. Q./'? < ;y"v ii onfirm new down position. press "My" until motor jogs OK /) > 5sec. ) Press simultaneously until... 2sec.... motor jogs onfirm new down position, press "My" until motor jogs OK L : - '-" "O N cc g I?"> r N (f) a D D '-" (f) a D,,_ (f) a D D ---,

11 RTS Motors - programming and Basic setting Basic Setting My position for NON TILT products.,.,.,., g:j <fl <fl ('"J Place the blind in desired position My can never be set the same as up or down position 5sec. / c_ onfirm the My position, press "My" until motor jogs OK Setting My position for TILT products - <fl Adjusting My position Repeat procedure to a new desired position _ 5s ij _ '. _ ; Place the blind in the down position Tilt up to desired slat angle onfirm the My position, press "My" until motor jogs OK co N Adjusting My position Repeat procedure to a new desired position & 1 Remove programmed My position ('"J 6 c -, 2 [t:s " lfai _-- " Place the blind in the my position or rro or - Q 5s ec. Press 'my' until... or...motor jogs

12 RTS Motors - programming and Basic setting Basic Set blind mode: Roller or Venetian Default setting Tilt & lift 25 RTS Venetian Roll up 28 RTS, Sonesse 3 & 4 Roller ';Q Place the blind half way down 2 hange the setting I?" r ;"i' N f) D D w f) D D -"' Press simultaneously... motor jogs Press simultaneously... motor jogs until... until...