BEA MATRIX INDUCTION LOOP. BEA - LZR-i30 RD BK GRN/WH BLK/WH YDC2 WH/BU

Transcription

1

2

3

4

5 R PART # WG NO SHEET NEXT ASSEMBLY ISION HISTORY 802E012 ESRIPTION EN BY APPROVE A RENAMETERMINALS FOR BEA AN PHOT 88 /31/2012 BJJ BEA - Falcon, Eagle, MS08 * US WH * 4-GN not used -YE BEA Motion s PHOTOEYES Photoeye Retroreflective or Thru Beam Receiver *** BEA ATIVATION PHOTOEYES Thru Beam Emitter OG Photoeye BEA - IRIS Presence Set to a value of -Reverse RAIO ONTROL 433MHz Radio ontrol 1. SET IP SWITHES 1&2 TO OFF. 2. PRESS LEARN W/NO ELAY. 3. PRESS TRANSMITTER TTON REPEATELY UNTIL BLUE LE ON REEIVER ILLUMINATES. Receiver WH GN *** BEA - K-12 Presence Set to a value of -Reverse not used not used WH GN PUSHTTONS & PULL-OS Switch SW SW Each device as shown. MISELLANEOUS ATIVATION BEA - IS-40 WH * GN not used YE WH/BLK *** GRN/BLK not used YE/BLK BEA IS40 Motion/Presence IS-40 Hold Open Set to a value of (-Reverse) OPEN/LOSE/STOP PUSHTTON STATION OPEN STOP LOSE X0 X? X4 Note: onsult i-omm manual to see which inputs can be assinged STOP function. onnect STOP to whichever input is selected to become STOP. No other devices should be connected to this input. Terminal Must be assigned to STOP through i-omm menu on both doors. (i.e. If is to be assigned a function of STOP, the menu ("Input Func ") should be set to a value of "1"). BEA - LZR-i30 Y2 GRN/WH BLK/WH not used GRN not used WH not used ORG not used ORG/BLK WH/ LZR-i30 Presence For sensor monitoring connect WH/ wire to Y2. The input must be changed to 19 - LZR In N/. onnect WH/ to otherwise and set the input to - Reverse N/. WIRELESS PUSHTTONS & PULL-OS Pairing: Host (Receiver) 4 2.4GHz less Activation To pair with a wireless device, first remove the plastic strip under the batteries in the remote unit to energize the device. On the Host (Receiver) press "Remote Pairing". The "RF om" LE will begin to flash. Next press the pair button on the remote unit. The units will then pair. Activate the door to test. Repeat procedure if necessary. BEA MATRIX INUTION LOOP INUTION LOOP ONTROLLER Standard configuration is combined mode with IP switches #1-9 in the OFF position and IP switch #10 in the ON position. For independent mode and other IP switch settings, consult the BEA Matrix User Manual V POWER 1 OPEN LSG RE WY SAFETY ATIVATOR LS Fault RF om STOP O/ 10 Remote Pairing OM NON-SEQUENTIAL 2 OOR INTERLOK N 2 oor Non-Sequential Interlock Note: onsult i-omm manual to see which inputs can be assigned interlock in function. onnect to whichever input is selected to become interlock in. No other devices should be connected to this input. Terminal must be assigned to Interlock through i-omm menu on both doors. (i.e. If is to be assigned a function of Interlock Input, the menu ("Input Func ") should be set to a value of "0") Output (K0 relay) should remain at the default setting of "0" on both doors. N YK2 YK2N N N B A ATIVATION OPTIONS 82 1/1/2014 TAH BEA RAIO ONTROLS 893 /1/2014 TAH NON-SEQUENTIAL 3 OOR INTERLOK N 3 oor Non-Sequential Interlock Only 1 door may be open at a time. = 0 Interlock In (Must be on to open) = 0 Interlock Out (On when door closed) = 0 Interlock Out (On when door closed) oor3 N NON-SEQUENTIAL 4 OOR INTERLOK N YK2 YK2N = 0 Interlock In (Must be on to open) = 0 Interlock Out (On when door closed) = 0 Interlock Out (On when door closed) YK2 = 0 Interlock Out (On when door closed) oor3 N YK2 YK2N oor4 N YK2 YK2N 4 oor Non-Sequential Interlock Only 1 door may be open at a time. B 12 STROBE N Beacon/Strobe Warning evice Strobe Additonal Relay Required 12A U.L. Listed.30 Amp Max 12A ALARM N Alarm Warning evice Strobe Additonal Relay Required 12A U.L. Listed.30 Amp Max WARNING EVIE RELAY J4- or ONTROL BOX WIRING PREANNOUNE RELAY J4-12 or Y_ PREANNOUNE EVIES NOTES This drawing assumes input functions are set to factory defaults. WARNING - never connect motion sensors to a toggle input. Terminals "X", "X" are automatic reclose. Terminal X on the motor terminal strip can be used for activation devices such as motion sensors and pull cords. Terminals "" are common for inputs. F or L AIR URTAIN INTERLOK (24V) N Air urtain Ouput Output om Note: onsult i-omm manual for available output functions. onnect & N to Air urtain control. hange to 1 (on when door not closed). INTERLOKS AIR URTAIN INTERLOK (12) Relay 14(3) 11(4) A1() A2(1) Air urtain Ouput Output om Y_ i-omm INSTALL SPT RELAY IN BOX OIL A1() A2(1) 14(3) 11(4) Note: onsult i-omm manual for available output functions. onnect relay contact to Air urtain control. hange Y_ to 1 (on when door not closed). Separate relay must be used for isolation with 12A. SEQUENTIAL INTERLOK N X N X 2 oor Sequential Interlock = 0 Interlock In X = Sequential Activation In = 0 Interlock Out = 1 Sequential Act. Out Note: Activation of oor 1 will automatically activate oor 2 (and vice versa) after the first door has closed. Sequence resets after both doors have cycled once. B ITEM QTY PART NO. ESRIPTION A **For true toggle operation use terminal "X". (Pull cords, push button or radio controls only.) ***For Reverse hold open connect sensors to UNUSE input. (i.e., X, or X and assign that input a function of "" in the i-omm menu. Multiple sensors can be connected in parallel. onsult i-omm manual and/or oor manual for additional instructions RITE-HITE OORS IN. OVER ANGLES FINISH INH TOLERANES UP TO /- 1 EG + / RAWN BY HEKE BY APPROVE BY INITIAL EN ISSUE REF O NOT SALE RAWING MM--YY TAH /11/ /11/2012 TITLE SIZE SALE MOEL NUMBER 9"=1' WG NO PARTS LIST / MATERIAL SPLITSEON SERIES ATIVATION WIRING i-omm II SplitSecond RITE-HITE OORS IN. 802E012 R SHEET A