2573 N.W. 74th Ave. Miami, Florida Phone: (305) /8672 Order Fax: (305)

Transcription

1 2573 N.W. 74th Ave. Miami, Florida Phone: (305) /8672 Order Fax: (305)

2 M o t o r F e a t u r e s DC Power - Utilizes direct current. Contact Closure - Allows operation using 2 momentary dry contacts from a 3rd party system or wall switch Tube Diameter - Diameter of roller shade motor tube. Radio Frequency - A remote control that utilizes radio waves. Tandem motor set - A drive and nondrive motor that function as one, more powerful, motor system. Enclosure - Extrusion that encases the roller tube for a complete blackout effect. Quiet - System uses a quiet motor. Solar Powered - Utilizes solar rays for energy. Fascia - Extrusion that is attached to the brackets and covers the hardware to block incoming light. 55mm Tube 1 3 8" " 52.8mm 55.8mm Motor Max. Weight Max. Width * : Single Shade Max. Width * : Coupled Max. Drop * : with Brackets Max. Drop * : with Fascia Fascia and Backplate Side and Sill Channel Width Shade Pocket, Closure and Hanger Motor Limit Type Motor Diameter RPM Turns nm db Rating Solar 16 lbs. 144 N/A Available Mechanical 45mm * Maximum width and maximum drop are dependent upon fabric selected. Contact factory for M e a s u r e m e n t G u i d e S t a n d a r d S y s t e m s Section 1 width Section 2 width Section 3 width Fabric Drop (height) C o u p l e d S y s t e m s Overall width (Bracket to Bracket) Section 1 width Section 2 width Section 3 width Fabric Drop (height) 2 Overall width (Bracket to Bracket)

3 L i g h t G a p I n f o r m a t i o n Note: Shades installed with optional side channels have no light gaps MINIMUM ADJUSTABLE BRACKET SYSTEM Solar Panel Motorized RS-20 without fascia - Solar-powered motor 2-13/16" 1-3/8" 3-3/8" 1-3/8" Light Gap 7/8" Light Gap Overall width of system 3/16" Motorized RS-20 with L-style fascia - Solar-powered motor 4" Tube Diameter 4 3/4" 1 1/16" Light Gap 9/16" Light Gap Overall width of system 2 3/16" Motorized RS-20 with Cassette - Solar-powered motor 4" 4-3/4" 1-1/16" Light Gap Overall width of system 9/16" Light Gap 3

4 M o u n t i n g I n f o r m a t i o n Shade Pocket Dimensions Side Channel Mounting Standard Side Dual M o u n t i n g B r a c k e t F e a t u r e s Standard Bracket For: Standard Coupler Bracket For: /2 1 1/2 1 1/2 2 3/4 2 3/4 2 3/4 3 1/4 3 1/4 3 1/4 4 Fascia Bracket For: Drop-in Coupler Bracket For: /4 4 3/4 1 1/2 2 3/ /4 4

5 P r o g r a m m i n g a n d O p e r a t i o n R e m o t e A d d i t i o n a l C o n t r o l s The solar-powered roller shade system is also available with wireless wall switches. These switches are available in single or doublechannel Additional switchplates and wall-mount boxes are available for complete installation packages. 5

6 I n t r o d u c t i o n The remote is designed to be used in operating automated roller shade systems. It has 6 channels and can operate 6 individual systems or 6 groups of systems. P r o g r a m m i n g t h e R e m o t e Initial Programming The time using the remote, the motor needs to recognize the remote. When you press the CHANNEL selection button, one of the channel indicating LED s will illuminate. Keep pressing the CHANNEL select button until the desired channel lights up. To enter program mode, the motor needs to be disconnected from the solar panel for 1 minute, then plug the motor back into the solar panel reinstate power. Within 90 seconds after power on, press and hold the OPEN and CLOSE buttons simultaneously. The selected channel number will light up with slow The roller will react with a movement to indicate the motor is receiving the signal from the remote and communication has been established. Test run the system by pressing the OPEN or CLOSE button. Change Travel Direction The directional icons on the remote should match the travel direction of the shade. If they do not, for example, when you press the OPEN button the shade closes, you may need to change the direction. To change the direction, put the motor into program mode. Press and hold the A and B buttons simultaneously, the channel light will slowly until the roller reacts with a movement. Test run the system by pressing the OPEN or CLOSE button. Deleting a Channel Press the CHANNEL button until the LED for the channel you want to delete lights up. Press and hold the OPEN and STOP buttons simultaneously until the roller reacts with a movement. The selected channel is now deleted from the motor. Deleting All Channels Press the CHANNEL button until the LED for the channel you want to delete lights up. Press and hold the STOP and CLOSE buttons simultaneously until the roller reacts with a movement. Now all channels that were previously programmed to this motor have been removed. To simply press any of the action buttons (OPEN or CLOSE) and verify the motor does not move. Warning: In order to prevent damage, never start programming with the shade in the far up position. 6

7 O p e r a t i n g t h e R e m o t e After the remote has been programmed, simply press the OPEN, STOP or CLOSE buttons to operate the roller shade. M o u n t i n g t h e R e m o t e Wall Mounted Cradle A cradle is provided with the remote to mount to the wall. First, use the provided hardware to screw the metal bracket to the desired mounting location. Next, slide the plastic cradle support into the bracket. Now, the cradle is properly installed and capable of holding the remote. Replacing the Battery M a i n t a i n i n g t h e R e m o t e The remote is powered by two Li-ion batteries, model number: CR2430 ( part number ). The battery lasts for over two years under normal operating condition. When channel LED s 1 and 6 light up at the same time, the batteries have been depleted and need to be replaced. This is a standard battery type and should be easily found at most electronic stores. Open the remote case by pushing the battery cover in an up direction. Once the battery cover is removed, the battery can be easily seen. Exchange the old battery for the new ones and replace the battery cover. 7

8 P r o g r a m m i n g : Q u i c k R e f e r e n c e START Select the required channel on remote control Connect motor to power supply (solar panel) Check power supply Press and hold the OPEN and CLOSE buttons within 90 seconds of power connection No The motor jogs? Yes Press the OPEN or CLOSE buttons to check the motor direction Unplug the motor for 60 seconds and then plug it back in No Is the direction correct? Press and hold the A and B buttons on the remote within 90 seconds Yes Motor jogs and direction is reversed Test run the motor by pressing the OPEN or CLOSE buttons END N.W. 74th Ave. Miami, Florida Phone: (305) /8672 Order Fax: (305) info@megamarinc.com