STEP BY STEP INSTALLATION INSTRUCTIONS. Studio Hardware. Wall Mount Single Rod Set Motivia Motorized

Transcription

1 STEP BY STEP INSTALLATION INSTRUCTIONS Studio Hardware Wall Mount Single Rod Set Motivia Motorized

2 Everything You Need Table of Contents Step 1 - Getting Started....3 Overview - Wall Mount Single Rod Set Motivia Motorized...4 Step 2 - Mounting the Brackets A Smooth Set-Up We want you to love your new hardware and that includes having a smooth installation experience. We recommend saving this guide. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at for more info on installation. We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be a painless as possible. Step 3 - Attaching Rod Connector Step 4 - Attaching the Finials...8 Step 5 - Securing Track to Brackets Mounting the Track...9 Mounting the Fascia....9 Step 6 - Attaching Power Source Step 7 - Mounting Remote Step 8 - Operating the Rod Set Step 8 - Operating the Rod Set Troubleshooting Care & Cleaning Customer Service Hours Monday Friday: 6am 6pm PT Saturday Sunday: 7am 4pm PT Safety Warranty...Back Cover smithandnoble.com 1 smithandnoble.com

3 Step 1 Parts & Tools Overview Getting Started Wall Mount Single Rod Set Motivia Motorized First, make sure you have all the parts and tools required to install your hardware. ALL THE HARDWARE YOU LL NEED: Pencil, tape measure, screwdriver, 1 8" drill bit, level, a drill with a 3 16" drill bit, a hammer and a 7mm wrench or small adjustable wrench. Then find wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. (see anchor screws below) Note: It s important to monitor the amount of pressure you apply when using a drill. If the screws are too tight this may cause the screw itself to break off in the wall or window frame. FASCIA FINIAL (PRE-ATTACHED) Parts MOTOR CARRIERS MASTER CARRIER WALL SCREWS STANDARD SPLICE CONNECTOR CHANNEL INDICATOR OPEN BUTTONS STOP CLOSE BUTTONS POWER DRILL (NOT INCLUDED) ANCHOR SCREWS (NOT INCLUDED) SCREWDRIVER & PENCIL (NOT INCLUDED) LEVEL (NOT INCLUDED) SCHEDULE CHANNEL SELECTION REMOTE CONTROL ROD QTY QTY ROD WIDTH " MOLLY BOLT SELF DRILLING ANCHOR TOGGLE BOLT /8 96" /8 192" 3 smithandnoble.com

4 Step 2 Mounting Brackets Step 2 Mounting Brackets STEP 1: Place the panel on the track. To ensure it drapes at the correct length, hold it up to the spot you wish to install it. Raise or lower your treatment as desired. After you ve located the ideal location, use a pencil to mark where the top of the rod is resting. STEP 3: Hold bracket so slotted holes are facing down. Place the brackets so that the horizontal plate of bracket is aligned with the marked height and then mark the location of the screw holes with your pencil. Once you ve established where everything should go, put the bracket aside and double-check to make sure the pencil marks are level with each other. Next, pre-drill the holes, using 1 8 drill bit, in their assigned spot, making sure it s the right depth for the supplied screws. If there is no backing behind drywall, use a 3 16 drill bit and insert anchors using hammer. Attach wall brackets using screws provided. STEP 2: Remove the panel from the track and then center the track over the window opening at the desired height. Using the pencil, mark where the ends of track are positioned; if you re using a center bracket, note the middle point between these two spots as well. If you have more than one center bracket spread these evenly between the two end brackets and center point. Measure 7 inward from the marks you ve made on both ends and mark those spots. This is where the end brackets will be installed. CENTER ROD Note: Do not use 3 16 drill bit or use anchors if there is wood backing behind drywall. Install your brackets. 5 smithandnoble.com

5 Step 3 Attaching the Rod Connector Step 3 Attaching the Rod Connector STEP 1: SPLICE JOINT STEP 1: Unfold the track Slowly bring the track assembly together (make sure the track joint board is centered on the track joint), and re-assemble the master carrier. MASTER CARRIER BELT BUTTON MASTER CARRIER JOINT BOARD SPLICE CONNECTOR STEP 2: Center the track joint bracket over STEP 2: PLASTIC CONNECTION PART SPLICE JOINT the track and hand tighten the screws. DO NOT OVERTIGHTEN THE SCREWS. Remove the screws and disassemble the underlap master carrier. STEP 3: Measure six inches on each side of the track joint bracket for wall brackets. MASTER CARRIER SPLICE CONNECTOR JOINT BOARD Repeat for back rod. Step 4 Attaching Finials STEP 3: Slide the plastic connection part out of the track and slip the belt button into the connection part. CONNECTION PARTS PLASTIC CONNECTOR BELT BUTTON FINIAL (PRE-ATTACHED) Finials will come already attached to the rods. 7 smithandnoble.com

6 Step 5 Securing Track to Brackets Step 6 Attaching Power Source Mounting the Track Make sure swivel brackets are in the open position (Figure 3). MOTOR DRIVE SHAFT LOCKING LEVER Attach motor to track by inserting drive shaft into motor joint box (Figure 5) and (Figure 6). Insert track into bracket and lock swivel bracket into place (Figure 4). Make sure track is centered inside fascia and tighten swivel brackets with phillips screwdriver. SWIVEL (OPEN) FIGURE 3 SWIVEL (CLOSED) MOTOR JOINT BOX FIGURE 5 Slide lever over until it locks motor in place (Figure 7). To release motor, hold motor while pulling down on lever and slide back to open position. UPPER "L" Plug in motor and use remote to operate. FIGURE 4 LOCKING LEVER (OPEN POSITION - UNLOCKED) NOTE: Remotes will be pre-programmed and paired to rod sets. For additional programming features or if hardware needs to be reprogrammed, See Studio Motorization Programming Guide. Mounting the Fascia UPPER "L" FIGURE 6 Place decorative fascia in between the top of track upper L bracket. (Figure 1 ) Place Fascia between here Mark the hole for each bracket on the top of the fascia and pre-drill with 1 8 drill bit (Figure 2). Measure proper depth (approx. 2½ ) so you do not drill all the way through fascia. FIGURE 1 LOCKING LEVER (CLOSED POSITION - LOCKED) Attach bracket and fascia with ¾ wood screws provided. FASCIA UPPER "L" FIGURE 7 FIGURE 2 9 smithandnoble.com

7 Step 7 Mounting Remote Step 8 Operating the Rod Set Mounting the Remote Base BASE PLATE COVER Remote Control Find a desired location on the wall to mount the magnetic base plate. With a small flathead screwdriver, gently pry up and remove base plate cover (See Figure 1). Note the screw holes on the back plate and the magnet inside the base plate. (See Figure 2) Mount base plate to wall using screws provided (use drywall anchors if necessary. (See Figure 3) Then from the bottom up, gently press the base plate cover back onto the base. (See Figure 4) Now your remote will magnetically stick onto the base. FIGURE 1 SCREW HOLE FIGURE 2 BASE PLATE COVER MAGNET SCREW HOLE BASE PLATE COVER BASE PLATE BASE PLATE CHANNEL INDICATOR OPEN STOP CLOSE CHANNEL SELECTION Select the desired channel with the CHANNEL key. The channel indicator will show the channel that is on. If it s on channel 0, the remote will control all rods in that remote at once. Use the left side controls only for single rod sets. Tapping the OPEN <> or CLOSE >< keys for less than 2 seconds will move the rod in short steps. Holding the OPEN or CLOSE keys down for more than 2 seconds before releasing, will operate the rod in the faster standard speed. Press the OPEN or CLOSE keys to open or close the draperies. Press the STOP key to stop the rod anywhere along the window. BASE PLATE FIGURE 3 BOTTOM "L" SHAPE. HOOK IN FIRST. THEN PRESS THE BASE PLATE COVER ONTO BASE BOTTOM TO TOP FIGURE 4 11 smithandnoble.com

8 Troubleshooting Care & Cleaning and Safety PROBLEM Rod set will not operate Master carriers will not open or close all the way. SOLUTION 1) Make sure that the motor is plugged in all the way and the motor is locked in place. 2) Make sure the battery is charged and connected to the motor. 3) Make sure the battery in the remote has the positive (+) symbol facing up. 4) Check to see if the cord is plugged in and power to the outlet. 5) If above items are all good, then reboot and relink your rod. a. Connect motor to its power source. b. Locate the Motor Setting Button c. Using a pencil press Motor Setting Button for 10 seconds or until the indicator light flashes. d. Then proceed to pair remote to the hardware See Programming Guide for Drapery Hardware 1) Check to see if master carriers are free from any obstructions. 2) Make sure there is an equal number of carriers on each side of the master carriers on a split-draw rod set. 3) If installing a rod segment, check to see if the screws on the track joint board have not been over-tightened. 4) See Programming Guide to restore motor to factory settings. Care & Cleaning Minimal care and cleaning is needed to maintain the beauty of your Hardware. To Vacuum: Use brush or dust head attachment. To Dust: Use soft, clean cloth. Safety First. Style Second To None. Great style should never come at the cost of safety. Every Smith & Noble window treatment conforms strictly to today s safety standards, including permanent tie-down devices and built-in cord stops. To protect young children and pets, there s no better way to eliminate risk than to use one of our Motivia motorized products. Rod set opens when pressing close buttons on the remote. 1) Hold the Motor Setting Button for 4 seconds or until the indicator light flashes once then once again. Release the button after the second flash. 2) Press the Left Close Button on the remote. Indicator light should flash 5 times. 3) Reverse of direction setting is now complete. I have reset the motor to factory settings and rod set still will not operate. 1) Follow STEP 1 in the Programming Guide and pair the remote to the hardware. 13 smithandnoble.com

9 Warranty Service The enjoyment of your products should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades, blinds or hardware must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at and we ll arrange for a repair or replacement ASAP Smith & Noble Home, Inc. All Rights Reserved SN032018