- PDF Free Download

Size: px

Start display at page:

Download ""

Jeffry Newman
5 years ago
Views:

SLOS070C JULY 979 REVISED SEPTEMBER 2004 Equivalent Input Noise Voltage... 3.5 nv/ Hz Typ Unity-Gain Bandwidth... 0 MHz Typ Common-Mode Rejection Ratio... 00 db Typ High DC Voltage Gain.

1 SLOS070C JULY 979 REVISED SEPTEMBER 2004 Equivalent Input Noise Voltage nv/ Hz Typ Unity-Gain Bandwidth... 0 MHz Typ Common-Mode Rejection Ratio db Typ High DC Voltage Gain V/mV Typ Peak-to-Peak Output Voltage Swing 32 V Typ With V CC = 8 V and R L = 600 High Slew Rate... 3 V/ s Typ Wide Supply-Voltage Range 3 V to 20 V Low Harmonic Distortion Offset Nulling Capability External Compensation Capability NE5534, SA D (SOIC), P (PDIP), OR PS (SOP) PACKAGE NE5534A, SA5534A...D (SOIC) OR P (PDIP) PACKAGE (TOP VIEW) BALANCE IN IN+ V CC NE5534P OP AMP LOW NOISE COMP/BAL V CC+ OUT COMP description/ordering information The NE5534, NE5534A, SA5534, and SA5534A are high-performance operational amplifiers combining excellent dc and ac characteristics. Some of the features include very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, and high slew rate. These operational amplifiers are compensated internally for a gain equal to or greater than three. Optimization of the frequency response for various applications can be obtained by use of an external compensation capacitor between COMP and COMP/BAL. The devices feature input-protection diodes, output short-circuit protection, and offset-voltage nulling capability with use of the BALANCE and COMP/BAL pins (see the application circuit diagram). For the NE5534A and SA5534A, a maximum limit is specified for the equivalent input noise voltage. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2004, Texas Instruments Incorporated POST OFFICE BOX DALLAS, TEXAS 75265

2 SLOS070C JULY 979 REVISED SEPTEMBER 2004 description/ordering information (continued) schematic TA VIOmax AT 25 C 0 C to 70 C 4 mv PDIP (P) SOIC (D) ORDERING INFORMATION PACKAGE ORDERABLE PART NUMBER TOP-SIDE MARKING Tube of 50 NE5534P NE5534P Tube of 50 NE5534AP NE5534AP Tube of 75 NE5534D Reel of 2500 NE5534DR NE5534 Tube of 75 Reel of 2500 NE5534AD NE5534ADR 5534A SOP (PS) Reel of 2000 NE5534PSR N5534 PDIP (P) 40 C to 85 C 4 mv SOIC (D) SOP (PS) Tube of 50 SA5534P SA5534P Tube of 50 SA5534AP SA5534AP Tube of 75 Reel of 2500 Tube of 75 Reel of 2500 Tube of 80 Reel of 2000 SA5534D SA5534DR SA5534AD SA5534ADR SA553APS SA553APSR SA5534 SA5534A SA5534 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at BALANCE COMP/BAL COMP VCC+ 00 pf 2 kω 2 kω IN pf 5 Ω IN 2 6 OUT 2 pf 7 pf 5 Ω 4 VCC All component values shown are nominal. 2 POST OFFICE BOX DALLAS, TEXAS 75265

3 SLOS070C JULY 979 REVISED SEPTEMBER 2004 symbol application circuit VCC+ COMP COMP/BAL 00 kω CC 22 kω IN IN+ + OUT BALANCE VCC Frequency Compensation and Offset-Voltage Nulling Circuit absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage: V CC+ (see Note ) V V CC (see Note ) V Input voltage either input (see Notes and 2) V CC+ Input current (see Note 3) ±0 ma Duration of output short circuit (see Note 4) Unlimited Package thermal impedance, θ JA (see Notes 5 and 6): D package C/W P package C/W PS package C/W Operating virtual junction temperature, T J C Storage temperature range, T stg C to 50 C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES:. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC. 2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage. 3. Excessive current will flow if a differential input voltage in excess of approximately 0.6 V is applied between the inputs, unless some limiting resistance is used. 4. The output may be shorted to ground or to either power supply. Temperature and/or supply voltages must be limited to ensure the maximum dissipation rating is not exceeded. 5. Maximum power dissipation is a function of TJ(max), θja, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) TA)/θJA. Operating at the absolute maximum TJ of 50 C can affect reliability. 6. The package thermal impedance is calculated in accordance with JESD 5-7. recommended operating conditions MIN MAX UNIT VCC+ Supply voltage 5 5 V VCC Supply voltage 5 5 V TA Operating free-air temperature range NE5534, NE5534A 0 70 SA5534, SA5534A C POST OFFICE BOX DALLAS, TEXAS

4 SLOS070C JULY 979 REVISED SEPTEMBER 2004 electrical characteristics, V CC ± = ±5 V, T A = 25 C (unless otherwise noted) VIO Input offset voltage PARAMETER TEST CONDITIONS MIN TYP MAX UNIT IIO Input offset current VO = 0 IIB Input bias current VO = 0 VO = 0, TA = 25 C RS = 50 Ω TA = Full range 5 TA = 25 C TA = Full range 400 TA = 25 C TA = Full range 2000 VICR Common-mode input voltage range ±2 ±3 V VO(PP) Maximum peak-to-peak output voltage swing RL 600 Ω AVD Large-signal differential voltage amplification Avd Small-signal differential voltage amplification f = 0 khz BOM Maximum-output-swing bandwidth VCC± = ±5 V VCC± = ±8 V VO = ±0 V, TA = 25 C RL 600 Ω TA = Full range 5 VO = ±0 V VCC± = ±8 V, RL 600 Ω, CC = 0 6 CC = 22 pf 2.2 CC = CC = 22 pf 95 VO = ±4 V, CC = 22 pf B Unity-gain bandwidth CC = 22 pf, CL = 00 pf 0 MHz ri Input resistance kω zo CMRR ksvr Output impedance Common-mode rejection ratio Supply-voltage rejection ratio ( VCC/ VIO) AVD = 30 db, CC = 22 pf, VO = 0, RS = 50 Ω VCC+ = ±9 V to ±5 V, VO = 0 RL 600 Ω, f = 0 khz VIC = VICRmin, RS = 50 Ω, 70 mv na na V V/mV V/mV khz 0.3 Ω db db IOS Output short-circuit current 38 ma ICC Supply current VO = 0, No load TA = 25 C 4 8 ma All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. For NE5534 and NE5534A, full range is 0 C to 70 C. For SA5534 and SA5534A, full range is 40 C to 85 C. 4 POST OFFICE BOX DALLAS, TEXAS 75265

5 SLOS070C JULY 979 REVISED SEPTEMBER 2004 operating characteristics, V CC ± = ±5 V, T A = 25 C SR tr PARAMETER Slew rate Rise time Overshoot factor Rise time Overshoot factor TEST CONDITIONS NE5534, NE5534A, SA5534A SA5534 TYP MIN TYP MAX CC = CC = 22 pf 6 6 VI I = 50 mv, RL = 600 Ω, CL = 00 pf VI I = 50 mv, RL = 600 Ω, CL = 500 pf AVD =, CC = 22 pf AVD =, CC = 47 pf UNIT V/µs ns % ns % f = 30 Hz Vn Equivalent input noise voltage f = khz nv/ Hz f = 30 Hz In Equivalent input noise current pa/ Hz f = khz F Average noise figure RS = 5 kω, f = 0 Hz to 20 khz 0.9 db POST OFFICE BOX DALLAS, TEXAS

6 SLOS070C JULY 979 REVISED SEPTEMBER 2004 TYPICAL CHARACTERISTICS Normalized Input Bias Current and Input Offset Current NORMALIZED INPUT BIAS CURRENT AND INPUT OFFSET CURRENT FREE-AIR TEMPERATURE Bias Offset TA Free-Air Temperature C Figure VCC± = ±5 V ÁÁVO(PP) V OPP Maximum Peak-to-Peak Output Voltage V ÁÁ MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE FREQUENCY CC = 22 pf 5 VCC± = ±5 V CC = 47 pf TA = 25 C 0 00 k 0 k 00 k M f Frequency Hz Figure 2 CC = 0 VD Differential Voltage Amplification V/mV A LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION FREQUENCY VCC± = ±5 V TA = 25 C CC = 22 pf 0 00 k 0 k 00 k M 0 M 00 M f Frequency Hz Figure 3 CC = 0 pf Normalized Slew Rate and Unity-Gain Bandwidth TA = 25 C NORMALIZED SLEW RATE AND UNITY-GAIN BANDWIDTH SUPPLY VOLTAGE Unity-Gain Bandwidth VCC± Supply Voltage V Figure 4 Slew Rate Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 6 POST OFFICE BOX DALLAS, TEXAS 75265

7 TYPICAL CHARACTERISTICS SLOS070C JULY 979 REVISED SEPTEMBER 2004 Normalized Slew Rate and Unity-Gain Bandwidth NORMALIZED SLEW RATE AND UNITY-GAIN BANDWIDTH FREE-AIR TEMPERATURE VCC± = ±5 V Unity-Gain Bandwidth Slew Rate TA Free-Air Temperature C THD Total Harmonic Distortion % k TOTAL HARMONIC DISTORTION FREQUENCY VCC± = ±5 V AVD = VI(rms) = 2 V TA = 25 C f Frequency Hz 4 k 0 k 40 k 00 k Figure 5 Figure 6 Vn Equivalent Input Noise Voltage nv/ Hz EQUIVALENT INPUT NOISE VOLTAGE FREQUENCY 0 00 k 0 k 00 k f Frequency Hz VCC± = ±5 V TA = 25 C SA5534, NE5534 SA5534A, NE5534A I n Equivalent Input Noise Current pa/ Hz EQUIVALENT INPUT NOISE CURRENT FREQUENCY VCC± = ±5 V TA = 25 C SA5534, NE5534 SA5534A, NE5534A k 0 k 00 k f Frequency Hz Figure 7 Figure 8 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX DALLAS, TEXAS

8 SLOS070C JULY 979 REVISED SEPTEMBER 2004 TYPICAL CHARACTERISTICS µv Total Equivalent Input Noise Voltage TOTAL EQUIVALENT INPUT NOISE VOLTAGE SOURCE RESISTANCE VCC± = ±5 V TA = 25 C f = 0 Hz to 20 khz f = 200 Hz to 4 khz k 0 k 00 k M RS Source Resistance Ω Figure 9 8 POST OFFICE BOX DALLAS, TEXAS 75265

9 PACKAGE OPTION ADDENDUM 4-Jun-2007 PACKAGING INFORMATION Orderable Device Status () Package Type Package Drawing Pins Package Qty NE5534AD ACTIVE SOIC D 8 75 Green (RoHS & NE5534ADE4 ACTIVE SOIC D 8 75 Green (RoHS & NE5534ADG4 ACTIVE SOIC D 8 75 Green (RoHS & NE5534ADR ACTIVE SOIC D Green (RoHS & NE5534ADRE4 ACTIVE SOIC D Green (RoHS & NE5534ADRG4 ACTIVE SOIC D Green (RoHS & Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3) NE5534AJG OBSOLETE CDIP JG 8 TBD Call TI Call TI NE5534AP ACTIVE PDIP P 8 50 Pb-Free (RoHS) NE5534APE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) NE5534D ACTIVE SOIC D 8 75 Green (RoHS & NE5534DE4 ACTIVE SOIC D 8 75 Green (RoHS & NE5534DG4 ACTIVE SOIC D 8 75 Green (RoHS & NE5534DR ACTIVE SOIC D Green (RoHS & NE5534DRE4 ACTIVE SOIC D Green (RoHS & NE5534DRG4 ACTIVE SOIC D Green (RoHS & NE5534IP OBSOLETE PDIP P 8 TBD Call TI Call TI NE5534P ACTIVE PDIP P 8 50 Pb-Free (RoHS) NE5534PE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) NE5534PSR ACTIVE SO PS Green (RoHS & NE5534PSRE4 ACTIVE SO PS Green (RoHS & NE5534PSRG4 ACTIVE SO PS Green (RoHS & SA5534AD ACTIVE SOIC D 8 75 Green (RoHS & SA5534ADE4 ACTIVE SOIC D 8 75 Green (RoHS & SA5534ADG4 ACTIVE SOIC D 8 75 Green (RoHS & SA5534ADR ACTIVE SOIC D Green (RoHS & N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Level--260C-UNLIM Level--260C-UNLIM Level--260C-UNLIM SA5534ADRE4 ACTIVE SOIC D Green (RoHS & Addendum-Page

10 PACKAGE OPTION ADDENDUM 4-Jun-2007 Orderable Device Status () Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3) SA5534ADRG4 ACTIVE SOIC D Green (RoHS & SA5534AP ACTIVE PDIP P 8 50 Pb-Free (RoHS) SA5534APE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) SA5534D ACTIVE SOIC D 8 75 Green (RoHS & SA5534DE4 ACTIVE SOIC D 8 75 Green (RoHS & SA5534DG4 ACTIVE SOIC D 8 75 Green (RoHS & SA5534DR ACTIVE SOIC D Green (RoHS & SA5534DRE4 ACTIVE SOIC D Green (RoHS & SA5534DRG4 ACTIVE SOIC D Green (RoHS & SA5534P ACTIVE PDIP P 8 50 Pb-Free (RoHS) SA5534PE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) SA5534PS ACTIVE SO PS 8 80 Green (RoHS & SA5534PSE4 ACTIVE SO PS 8 80 Green (RoHS & SA5534PSG4 ACTIVE SO PS 8 80 Green (RoHS & SA5534PSR ACTIVE SO PS Green (RoHS & SA5534PSRE4 ACTIVE SO PS Green (RoHS & SA5534PSRG4 ACTIVE SO PS Green (RoHS & N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Level--260C-UNLIM Level--260C-UNLIM Level--260C-UNLIM Level--260C-UNLIM Level--260C-UNLIM Level--260C-UNLIM () The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & - please check for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either ) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & : TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.% by weight in homogeneous material) Addendum-Page 2

11 PACKAGE OPTION ADDENDUM 4-Jun-2007 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3

12 PACKAGE MATERIALS INFORMATION 22-Feb-2008 TAPE AND REEL BOX INFORMATION Device Package Pins Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P (mm) W (mm) Pin Quadrant NE5534ADR D 8 SITE Q NE5534DR D 8 SITE Q NE5534PSR PS 8 SITE Q SA5534ADR D 8 SITE Q SA5534DR D 8 SITE Q SA5534PSR PS 8 SITE Q Pack Materials-Page

13 PACKAGE MATERIALS INFORMATION 22-Feb-2008 Device Package Pins Site Length (mm) Width (mm) Height (mm) NE5534ADR D 8 SITE NE5534DR D 8 SITE NE5534PSR PS 8 SITE SA5534ADR D 8 SITE SA5534DR D 8 SITE SA5534PSR PS 8 SITE Pack Materials-Page 2

14 MECHANICAL DATA MCER00A JANUARY 995 REVISED JANUARY 997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE (0,6) (9,00) (7,) (6,22) (,65) (,4) (,60) 0.05 (0,38) (0,5) MIN 0.30 (7,87) (7,37) (5,08) MAX Seating Plane 0.30 (3,30) MIN 0.00 (2,54) (0,58) 0.05 (0,38) 0.04 (0,36) (0,20) /C 08/96 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. This package can be hermetically sealed with a ceramic lid using glass frit. D. Index point is provided on cap for terminal identification. E. Falls within MIL STD 835 GDIP-T8 POST OFFICE BOX DALLAS, TEXAS 75265

15 MECHANICAL DATA MPDI00A JANUARY 995 REVISED JUNE 999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE (0,60) (9,02) (6,60) (6,0) (,78) MAX (0,5) MIN (8,26) (7,62) 0.05 (0,38) (5,08) MAX Gage Plane Seating Plane 0.25 (3,8) MIN 0.00 (0,25) NOM 0.02 (0,53) 0.05 (0,38) 0.00 (2,54) 0.00 (0,25) M (0,92) MAX /D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-00 For the latest package information, go to POST OFFICE BOX DALLAS, TEXAS 75265

n/a NE5534P LOW NOISE OP AMP (RC)

DATA SHEET Order code Manufacturer code Description 82-0734 n/a NE5534P LOW NOISE OP AMP (RC) The enclosed information is believed to be correct, Information may change without notice due to product improvement.