Ultra Low Noise Variable Gain Low Frequency Voltage Amplifier
|
|
|
- Letitia Gibson
- 5 years ago
- Views:
Transcription
1 Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommanded for Low Impedance Sources Smaller than 50 Ω Ultra low Input Voltage Noise: 400 pv/ Hz AC Coupled, Single Ended Bandwidth 1.5 Hz khz, Switchable to 1 khz Local and Remote Control Applications Ultra-Low-Noise Laboratory Amplifier Pulsed Thermal EMF Analysis Chopped Thermopiles / Bolometers Industrial Sensors Detector Preamplifier Integrated Measurement Systems Block Diagram Ultra-Low-Noise Input Stage AC Coupling Gain Amplifier Gain Amplifier Lowpass-Filter f -3dB = 1/100 khz INPUT 40 db 0 db 20 db 0 db 40 db OUTPUT 102/17 / V02 / HW / femto/voltage/dlpva-100-bun-s Parameter Control Unit POWER Supply SUPPLY Voltage Regulator IN (+/-15V) Manual Optocoupler Switch Isolate Unit OUT (+/-12V, +5V) DIG. CONTROL POWER SUPPLY INPUTS OUTPUT BS DE-/SP/R3/13OCT05
2 Specifications Test Conditions Vs = ± 15 V, Ta = 25 C Gain Gain Values 40, 60, 80, 100 db indicated by four LEDs Gain Accuracy ± 0.1 % (between settings) ± 1 % (overall) Gain Flatness ± 0.1 db Frequency Response Lower Cut-Off Frequency 1.5 Hz Upper Cut-Off Frequency 100 khz, switchable to 1 khz Upper Cut-Off Frequency Rolloff 12 db/oct. Time Response Rise / Fall Time (10% - 90%) 3.5 µs (@ BW = 100 khz) 350 µs (@ BW = 1 khz) Input Input Impedance 1 kω Equivalent Input Voltage Noise Gain Setting Noise 100 db 400 pv/ Hz 80 db 420 pv/ Hz 60 db 800 pv/ Hz 40 db 6 nv/ Hz Equivalent Input Current Noise 3 pa/ Hz 1/f-Noise Corner 100 Hz Input Bias Current 30 µa Maximum Input DC-Offset Voltage for Linear Amplification ± 90 mv Important Notice: The input must see a source Impedance below 200 Ω to function properly! 202/17 / V02 / HW / femto/voltage/dlpva-100-bun-s Output Output Impedance 50 Ω (terminate with > 10 kω for best performance) Output Voltage Range for linear Amplification ± 10 V (@ > 10 kω load) Output Current (max.) ± 20 ma Output Overload Recovery Time 0.5 ms (after 20x overload) Overload LED The amplifier features a LED to signalize an overload condition. The Overload LED will turn on if the signal level within the signal path exceeds the linear operating range. In order to ensure the correct operation of the amplifier without signal distortions reduce the gain setting until the Overload LED turns off. The Overload LED may also turn on when the amplifier is operated with open input or with a high source impedance. For proper operation please use a source impedance of less than 100 Ω or switch to a lower gain setting. Remote Digital Control Control Input Voltage Range Low: V High: V, TTL / CMOS compatible Control Input Current 0 0 V, V, V Overload Output Non active: + 5 V, max. 1 ma, active: 0.8 V, max. -10 ma Power Supply Supply Voltage ± 15 V (± 14.5 V to ± 16 V) Supply Current ± 55 ma typ. (depends on operating conditions, recommended power supply capability minimum 150 ma) Case Weight 0.32 kg (0.7 lbs) Material AlMg4.5Mn, nickel-plated
3 Temperature Range Storage Temperature - 40 C to C Operating Temperature 0 C to + 60 C Absolute Maximum Ratings Power Supply Voltage ± 21 V Control Input Voltage + 16 V / - 5 V Signal Input Voltage ± 4 V Overvoltage at the signal input can severely degrade the noise performance or destroy the amplifier! Connectors Input BNC Output BNC Power Supply LEMO series 1S, 3-pin fixed socket Pin 1: + 15V Pin 2: - 15V Pin 3: GND 302/17 / V02 / HW / femto/voltage/dlpva-100-bun-s Control Port Sub-D 25-pin, female, qual. class 2 Pin 1: +12 V (stabilized power supply output, max. 100 ma) Pin 2: -12 V (stabilized power supply output, max. 100 ma) Pin 3: AGND (analog ground) Pin 4: +5 V (stabilized power supply output, max. 50 ma) Pin 5: digital output: overload Pin 6: NC Pin 7: NC Pin 8: NC Pin 9: DGND (ground f. digital control Pin 10-25) Pin 10: NC Pin 11: digital control input: gain, LSB Pin 12: digital control input: gain, MSB Pin 13: NC Pin 14: digital control input: 100 khz / 1 khz Pin 15-25: NC
4 Remote Control Operation General Remote control input bits are opto-isolated and connected by logical OR to local switch setting. For remote control a switch setting, set the corresponding local switch to 0 db and 1 khz and select the wanted setting via a bit-code at the corresponding digital inputs. Mixed operation, e.g. local gain setting and remote controlled bandwidth setting, is also possible. Gain Setting Gain Pin 11 Pin db low low 60 db high low 80 db low high 100 db high high Bandwidth Setting Bandwidth Pin 14 1 khz low 100 khz high Typical Performance Characteristics Frequency Response (Logarithmic) 402/17 / V02 / HW / femto/voltage/dlpva-100-bun-s
5 Dimensions 157 mm 150 mm 137 mm 15 mm IN OUT POWER 3.3 mm 19 mm 14 mm 27 mm 18 mm 44 mm 51 mm 79 mm 86 mm 107 mm DZ-DLPVA-BUN-S 502/17 / V02 / HW / femto/voltage/dlpva-100-bun-s Specifications are subject to change without notice. Information furnished herin is believed to be accurate and reliable. However, no responsibility is assumed by FEMTO Messtechnik GmbH for its use, nor for any infringement of patents or other rights granted by implication or otherwise under any patent rights of FEMTO Messtechnik GmbH. Product names mentioned may also be trademarks used here for identification purposes only. by FEMTO Messtechnik GmbH Printed in Germany
Low Noise Variable Gain Low Frequency Voltage Amplifier
Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled, Single
Ultra Low-Noise Variable Gain Low-Frequency Voltage Amplifier
Features Variable gain 40 to 100 db, switchable in 20 db steps Bipolar input stage, recommended for low impedance sources smaller than 50 Ω Ultra low input voltage noise: 400 pv/ Hz AC coupled, single
Variable Gain Low Frequency Voltage Amplifier
Features Applications 20 to 80 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 1 kω Single Ended and True Differential Input Models Bandwidth DC -
Low Noise Variable Gain Low Frequency Voltage Amplifier
Measurement Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled,
Low Noise Variable Gain Low Frequency Voltage Amplifier
Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled, Single
Variable Gain 100 MHz Wideband Voltage Amplifier
Features 10 to 60 db, Switchable in 10 db Steps Bandwidth DC... 100 MHz, Switchable to 10 MHz Built-In Temperature Compensation for Low Drift of 0.6 µv/k 2.5 nv/ Hz Input Noise Switchable AC/DC-Coupling
Specifications Test Conditions Vs = ± 15 V, Ta = 25 C Gain Gain Values 40, 60, 80, 100 db indicated by four LEDs Gain Accuracy ± 0.1 % (between settin
Electro Optical Components, Inc. SUNSTAR 传感与控制 http://www.sensor-ic.com/ 5460 Skylane Boulevard, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com Features Variable Gain 40
Variable-Gain High Speed Current Amplifier
Features Transimpedance (Gain) Switchable from 1 x 10 2 to 1 x 10 8 V/A Bandwidth from DC up to 200 MHz Upper Cut-Off Frequency Switchable to 1 MHz, 10 MHz or Full Bandwidth Switchable AC/DC Coupling Adjustable
Variable-Gain High Speed Current Amplifier
Features Transimpedance (gain) switchable from 1 x 10 2 to 1 x 10 8 V/A Bandwidth from DC up to 200 MHz Upper cut-off frequency switchable to 1 MHz, 10 MHz or full bandwidth Switchable AC/DC coupling Adjustable
Variable Gain Sub Femto Ampere Current Amplifier
Features 0.4 fa Peak-Peak Noise Very High Dynamic Range: Sub-fA to 1 ma (> 240 db) Transimpedance (Gain) Switchable from 1 x 10 4 to 1 x 10 13 V/A Bandwidth up to 400 Hz, Rise Time Down to 0.8 ms - Independent
Variable Gain Photoreceiver - Fast Optical Power Meter
The picture shows model -FC with fiber optic input. Features Conversion gain switchable from 1 x 10 3 to 1 x 10 11 V/W InGaAs-PIN detector Spectral range 900-1700 nm Calibrated at 1550 nm (fiber optic
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
Electro Optical Components, Inc. SUNSTAR 传感与控制 TEL: FAX: Skylane Boulev
Electro Optical Components, Inc. 5460 Skylane Boulevard, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com Features Transimpedance (Gain) Switchable from 1 x 10 3 to 1 x 10
Lock-In-Amplifier Module
Features BNC Connectors for Input and Output Signals Rugged Aluminium Housing Single Phase Detection with X Output Working Frequency 5 Hz... 10 khz, Digital Phase Shifter 0... 360 Parameter Control by
200 MHz Variable Gain Photoreceiver
The image shows model -FST with 1.035-40 threaded flange and coupler ring. Features Applications Adjustable transimpedance gain from 10 2 to 10 8 V/A Wide bandwidth up to 200 MHz Si-PIN photodiode covering
200 MHz Photoreceiver with Si PIN Photodiode
The picture shows the -FS with free space input. The photoreceiver will be delivered without post holder and post. Features Si PIN Detector, 0.8 mm Active Diameter Spectral Range 320... 1000 nm Bandwidth
High-Speed Photoreceiver with Si PIN Photodiode
The photoreceiver will be delivered without post holder and post Features Si PIN Detector, 0.8 mm Active Diameter Spectral Range 320... 1000 nm Bandwidth DC... 200 MHz Amplifier Transimpedance (Gain) 2.0
Variable Gain Photoreceiver Fast Optical Power Meter
The picture shows model -FC with fiber optic input. Features Si-PIN detector, active area 1.1 x 1.1 mm 2 Spectral range 190-1000 nm Very low noise, NEP down to 17 fw/ Hz Bandwidth up to 500 khz Conversion
Variable Gain Photoreceiver Fast Optical Power Meter
The picture shows model -FC with fiber optic input. Features InGaAs-PIN detector, active diameter 0.3 mm (free space versions), 80 µm integrated ball lens (FC version) Spectral range 900-1700 nm Very low
400 MHz Photoreceiver with Si PIN Photodiode
The picture shows the -FS. The photoreceiver will be delivered without post holder and post. Features Si PIN Detector, 0.8 mm Active Diameter Spectral Range 320... 1000 nm Bandwidth DC... 400 MHz Amplifier
400 MHz Photoreceiver with InGaAs PIN Photodiode
The picture shows the -FS with free space input. The photoreceiver will be delivered without post holder and post. Features InGaAs PIN detector Spectral range 900... 1700 nm Bandwidth DC... 400 MHz Amplifier
Great Britain: LASER COMPONENTS (UK) Ltd., Phone: , Fax: , France: LASER COMPONENTS
F E M T O P H O T O R E C E I V E R O V E R V I E W 2 0 0 5 S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y Selection Guide Photoreceivers Model Spectral Calibration Bandwidth Min.
Lock-In Amplifier Module Series LIA-MV(D)-200
Operating Manual Lock-In Amplifier Module Series LIA-MV(D)-200 6/206 Rev. 5 Table of Contents Introduction 4 2 Models of the LIA-MV(D)-200 Series 4 3 Absolute Maximum Ratings 5 4 Specifications 5 5 Standard
What Kind of Application Do You Have?
f e m t o P R O D U C T o v e r v i e w S o p h i s t i c a t e d T o o l s f o r S i g n a l R e c o v e r y FEMTO Amplifier selection guide What Kind of Application Do You Have? Amplification of Small
Ultralow Input Bias Current Operational Amplifier AD549
Ultralow Input Bias Current Operational Amplifier AD59 FEATURES Ultralow input bias current 60 fa maximum (AD59L) 250 fa maximum (AD59J) Input bias current guaranteed over the common-mode voltage range
Zero Drift, Unidirectional Current Shunt Monitor AD8219
Zero Drift, Unidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to +85 V survival Buffered output voltage Gain = 6 V/V Wide operating temperature range:
High Common-Mode Voltage, Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage, Programmable Gain Difference Amplifier AD628 FEATURES FUNCTIONAL BLOCK DIAGRAM High common-mode input voltage range ±20 V at VS = ±5 V Gain range 0. to 00 Operating temperature
High Accuracy 8-Pin Instrumentation Amplifier AMP02
a FEATURES Low Offset Voltage: 100 V max Low Drift: 2 V/ C max Wide Gain Range 1 to 10,000 High Common-Mode Rejection: 115 db min High Bandwidth (G = 1000): 200 khz typ Gain Equation Accuracy: 0.5% max
OBSOLETE. Self-Contained Audio Preamplifier SSM2017 REV. B
a FEATURES Excellent Noise Performance: 950 pv/ Hz or 1.5 db Noise Figure Ultralow THD: < 0.01% @ G = 100 Over the Full Audio Band Wide Bandwidth: 1 MHz @ G = 100 High Slew Rate: 17 V/ s typ Unity Gain
Model 3102D 0-2 kv H.V. Power Supply
Features Compact single width NIM package Regulated up to ±2000 V dc. 1 ma output Noise and ripple 3 mv peak to peak Overload and short circuit protected Overload, inhibit and polarity status indicators
TDA W AUDIO AMPLIFIER
TDA2006 12W AUDIO AMPLIFIER DESCRIPTION The TDA2006 is a monolithic integrated circuit in Pentawatt package, intended for use as a low frequency class "AB" amplifier. At ±12V, d = 10 % typically it provides
Quad Audio Switch REV. B BLOCK DIAGRAM OF ONE SWITCH CHANNEL
a FEATURES CIickless Bilateral Audio Switching Four SPST Switches in a -Pin Package Ultralow THD+N:.8% @ khz ( V rms, R L = k ) Low Charge Injection: 3 pc typ High OFF Isolation: db typ (R L = k @ khz)
High Resolution, Zero-Drift Current Shunt Monitor AD8217
High Resolution, Zero-Drift Current Shunt Monitor AD8217 FEATURES High common-mode voltage range 4.5 V to 8 V operating V to 85 V survival Buffered output voltage Wide operating temperature range: 4 C
LF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER
LF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER INTERNALLY ADJUSTABLE INPUT OFFSET VOLTAGE LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW
HA-2600, HA Features. 12MHz, High Input Impedance Operational Amplifiers. Applications. Pinouts. Ordering Information
HA26, HA26 September 998 File Number 292.3 2MHz, High Input Impedance Operational Amplifiers HA26/26 are internally compensated bipolar operational amplifiers that feature very high input impedance (MΩ,
EL2142. Features. Differential Line Receiver. Applications. Ordering Information. Pinout. Data Sheet February 11, 2005 FN7049.1
Data Sheet FN7049.1 Differential Line Receiver The is a very high bandwidth amplifier designed to extract the difference signal from noisy environments, and is thus primarily targeted for applications
Low Power, Precision, Auto-Zero Op Amps AD8538/AD8539 FEATURES Low offset voltage: 13 μv maximum Input offset drift: 0.03 μv/ C Single-supply operatio
Low Power, Precision, Auto-Zero Op Amps FEATURES Low offset voltage: 3 μv maximum Input offset drift:.3 μv/ C Single-supply operation: 2.7 V to 5.5 V High gain, CMRR, and PSRR Low input bias current: 25
High Common-Mode Voltage Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage Programmable Gain Difference Amplifier FEATURES High common-mode input voltage range ±12 V at VS = ±15 V Gain range.1 to 1 Operating temperature range: 4 C to ±85 C Supply voltage
150 μv Maximum Offset Voltage Op Amp OP07D
5 μv Maximum Offset Voltage Op Amp OP7D FEATURES Low offset voltage: 5 µv max Input offset drift:.5 µv/ C max Low noise:.25 μv p-p High gain CMRR and PSRR: 5 db min Low supply current:. ma Wide supply
AD8218 REVISION HISTORY
Zero Drift, Bidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to 85 V survival Buffered output voltage Gain = 2 V/V Wide operating temperature range:
Rail-to-Rail, High Output Current Amplifier AD8397
Rail-to-Rail, High Output Current Amplifier FEATURES Dual operational amplifier Voltage feedback Wide supply range from 3 V to 24 V Rail-to-rail output Output swing to within.5 V of supply rails High linear
TL061 TL061A - TL061B
TL61 TL61A - TL61B LOW POWER J-FET SINGLE OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT
Precision Micropower Single Supply Operational Amplifier OP777
a FEATURES Low Offset Voltage: 1 V Max Low Input Bias Current: 1 na Max Single-Supply Operation: 2.7 V to 3 V Dual-Supply Operation: 1.35 V to 15 V Low Supply Current: 27 A/Amp Unity Gain Stable No Phase
Dual Precision, Low Cost, High Speed BiFET Op Amp AD712-EP
Dual Precision, Low Cost, High Speed BiFET Op Amp FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +125 C) Controlled manufacturing baseline One
Ultralow Offset Voltage Dual Op Amp AD708
Ultralow Offset Voltage Dual Op Amp FEATURES Very high dc precision 30 μv maximum offset voltage 0.3 μv/ C maximum offset voltage drift 0.35 μv p-p maximum voltage noise (0. Hz to 0 Hz) 5 million V/V minimum
TDA W Hi-Fi AUDIO AMPLIFIER
TDA2030 14W Hi-Fi AUDIO AMPLIFIER DESCRIPTION The TDA2030 is a monolithic integrated circuit in Pentawatt package, intended for use as a low frequency class AB amplifier. Typically it provides 14W output
Isolated Linearized 4-Wire RTD Input 5B35 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated Linearized 4-Wire RTD Input 5B35 FEATURES Single-channel signal conditioning module that Amplifies, Protects, Filters, and Isolates Analog Input. Isolates and protects a wide variety of four-wire
6500V/µs, Wideband, High-Output-Current, Single- Ended-to-Differential Line Drivers with Enable
99 Rev ; /99 EVALUATION KIT AVAILABLE 65V/µs, Wideband, High-Output-Current, Single- General Description The // single-ended-todifferential line drivers are designed for high-speed communications. Using
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5
Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load
Quad 12-Bit Digital-to-Analog Converter (Serial Interface)
Quad 1-Bit Digital-to-Analog Converter (Serial Interface) FEATURES COMPLETE QUAD DAC INCLUDES INTERNAL REFERENCES AND OUTPUT AMPLIFIERS GUARANTEED SPECIFICATIONS OVER TEMPERATURE GUARANTEED MONOTONIC OVER
Improved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
Self-Contained Audio Preamplifier SSM2019
a FEATURES Excellent Noise Performance:. nv/ Hz or.5 db Noise Figure Ultra-low THD:
Isolated, Frequency Input 5B45 / 5B46 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated, Frequency Input 5B45 / 5B46 FEATURES Isolated Frequency Input. Amplifies, Protects, Filters, and Isolates Analog Input. Generates an output of 0 to +5V proportional to input frequency. Model
LOW NOISE AMPLIFIER SA SERIES
LOW NOISE AMPLIFIER SA SERIES Accurate and ultra low noise measurements of very small signals Achieve one of the highest level of low noise amplification SA600 series SA400 series Differential input SA200
Dual Low Offset, Low Power Operational Amplifier OP200
Dual Low Offset, Low Power Operational Amplifier OP200 FEATURES Low input offset voltage: 75 μv maximum Low offset voltage drift, over 55 C < TA < +25 C 0.5 μv/ C maximum Low supply current (per amplifier):
High Voltage, Current Shunt Monitor AD8215
High Voltage, Current Shunt Monitor AD825 FEATURES ±4 V HBM ESD High common-mode voltage range 2 V to +65 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range 8-Lead
ADA485-/ADA485- TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... Specifications... 3 Spe
NC NC NC NC 5 6 7 8 6 NC 4 PD 3 PD FEATURES Ultralow power-down current: 5 na/amplifier maximum Low quiescent current:.4 ma/amplifier High speed 75 MHz, 3 db bandwidth V/μs slew rate 85 ns settling time
Voltage-to-Frequency and Frequency-to-Voltage Converter ADVFC32
a FEATURES High Linearity 0.01% max at 10 khz FS 0.05% max at 100 khz FS 0.2% max at 500 khz FS Output TTL/CMOS Compatible V/F or F/V Conversion 6 Decade Dynamic Range Voltage or Current Input Reliable
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
High Common-Mode Rejection. Differential Line Receiver SSM2141 REV. B FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection
a FEATURES High Common-Mode Rejection DC: 100 db typ 60 Hz: 100 db typ 20 khz: 70 db typ 40 khz: 62 db typ Low Distortion: 0.001% typ Fast Slew Rate: 9.5 V/ s typ Wide Bandwidth: 3 MHz typ Low Cost Complements
Obsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s) STG3684
LOW VOLTAGE 0.5Ω MAX DUAL SPDT SWITCH WITH BREAK BEFORE MAKE FEATURE HIGH SPEED: t PD = 0.3ns (TYP.) at V CC = 3.0V t PD = 0.4ns (TYP.) at V CC = 2.3V ULTRA LOW POWER DISSIPATION: I CC = 0.2µA (MAX.) at
Micropower Precision CMOS Operational Amplifier AD8500
Micropower Precision CMOS Operational Amplifier AD85 FEATURES Supply current: μa maximum Offset voltage: mv maximum Single-supply or dual-supply operation Rail-to-rail input and output No phase reversal
Octal Sample-and-Hold with Multiplexed Input SMP18
a FEATURES High Speed Version of SMP Internal Hold Capacitors Low Droop Rate TTL/CMOS Compatible Logic Inputs Single or Dual Supply Operation Break-Before-Make Channel Addressing Compatible With CD Pinout
OBSOLETE. Low Cost Quad Voltage Controlled Amplifier SSM2164 REV. 0
a FEATURES Four High Performance VCAs in a Single Package.2% THD No External Trimming 12 db Gain Range.7 db Gain Matching (Unity Gain) Class A or AB Operation APPLICATIONS Remote, Automatic, or Computer
Quad Low Offset, Low Power Operational Amplifier OP400
Quad Low Offset, Low Power Operational Amplifier OP4 FEATURES Low input offset voltage 5 μv max Low offset voltage drift over 55 C to 25 C,.2 pv/ C max Low supply current (per amplifier) 725 μa max High
ASK Cards. Features Analog signal isolation Digital signal isolation. Applications
GHM Messtechnik GmbH Sales Center International Schloßstraße 6 88453 Erolzheim Germany Fon +49-7354-937233-0 Fax -88 www.ghm-messtechnik.de info@ghm-messtechnik.de Product Information Features System Sources
TL081 TL081A - TL081B
TL081 TL081A - TL081B GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION
TDA W Hi-Fi AUDIO POWER AMPLIFIER
32W Hi-Fi AUDIO POWER AMPLIFIER HIGH OUTPUT POWER (50W MUSIC POWER IEC 268.3 RULES) HIGH OPERATING SUPPLY VOLTAGE (50V) SINGLE OR SPLIT SUPPLY OPERATIONS VERY LOW DISTORTION SHORT CIRCUIT PROTECTION (OUT
PIN CONFIGURATIONS FEATURES APPLICATION ORDERING INFORMATION. FE, N Packages
DESCRIPTION The are monolithic sample-and-hold circuits which utilize high-voltage ion-implant JFET technology to obtain ultra-high DC accuracy with fast acquisition of signal and low droop rate. Operating
AD MHz, 20 V/μs, G = 1, 10, 100, 1000 i CMOS Programmable Gain Instrumentation Amplifier. Preliminary Technical Data FEATURES
Preliminary Technical Data 0 MHz, 20 V/μs, G =, 0, 00, 000 i CMOS Programmable Gain Instrumentation Amplifier FEATURES Small package: 0-lead MSOP Programmable gains:, 0, 00, 000 Digital or pin-programmable
Low Cost, General Purpose High Speed JFET Amplifier AD825
a FEATURES High Speed 41 MHz, 3 db Bandwidth 125 V/ s Slew Rate 8 ns Settling Time Input Bias Current of 2 pa and Noise Current of 1 fa/ Hz Input Voltage Noise of 12 nv/ Hz Fully Specified Power Supplies:
Isolated, Linearized RTD Input 7B34 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated, Linearized RTD Input 7B34 FEATURES Amplifies, Protects, Filters, and interfaces input voltages from a wide variety of two and three-wire platinum, copper and nickel Resistor Temperature Detectors
16 V Auto-Zero, Rail-to-Rail Output Operational Amplifiers AD8638/AD8639
6 V Auto-Zero, Rail-to-Rail Output Operational Amplifiers AD8638/AD8639 FEATURES Low offset voltage: 9 µv maximum Offset drift:.4 µv/ C maximum Rail-to-rail output swing 5 V to 6 V single-supply or ±2.5
1 MHz to 8 GHz, 70 db Logarithmic Detector/Controller AD8318-EP
Enhanced Product FEATURES Wide bandwidth: MHz to 8 GHz High accuracy: ±. db over db range (f
High Voltage, Current Shunt Monitor AD8215
FEATURES ±4 V human body model (HBM) ESD High common-mode voltage range V to +6 V operating 3 V to +68 V survival Buffered output voltage Wide operating temperature range 8-Lead SOIC: 4 C to + C Excellent
12-Bit Successive-Approximation Integrated Circuit ADC ADADC80
2-Bit Successive-Approximation Integrated Circuit ADC FEATURES True 2-bit operation: maximum nonlinearity ±.2% Low gain temperature coefficient (TC): ±3 ppm/ C maximum Low power: 8 mw Fast conversion time:
2 GHz to 6 GHz, 500 W Power Amplifier HMC8113
Data Sheet FEATURES 2 GHz to 6 GHz frequency range 85 db typical small signal gain 57 dbm typical saturated output power 61 db gain control range with 1 db LSB Standard 5U 19-inch rack chassis (per EIA-310D)
easypll UHV Preamplifier Reference Manual
easypll UHV Preamplifier Reference Manual 1 Table of Contents easypll UHV-Pre-Amplifier for Tuning Fork 2 Theory... 2 Wiring of the pre-amplifier... 4 Technical specifications... 5 Version 1.1 BT 00536
Software Programmable Gain Amplifier AD526
a FEATURES Digitally Programmable Binary Gains from to 6 Two-Chip Cascade Mode Achieves Binary Gain from to 256 Gain Error: 0.0% Max, Gain =, 2, 4 (C Grade) 0.02% Max, Gain = 8, 6 (C Grade) 0.5 ppm/ C
Low Cost Low Power Instrumentation Amplifier AD620
Low Cost Low Power Instrumentation Amplifier AD60 FEATURES Easy to use Gain set with one external resistor (Gain range to 0,000) Wide power supply range (±.3 V to ±8 V) Higher performance than 3 op amp
4 MHz, 7 nv/ Hz, Low Offset and Drift, High Precision Amplifier ADA EP
Enhanced Product FEATURES Low offset voltage and low offset voltage drift Maximum offset voltage: 9 µv at TA = 2 C Maximum offset voltage drift:.2 µv/ C Moisture sensitivity level (MSL) rated Low input
Low Cost JFET Input Operational Amplifiers ADTL082/ADTL084
Low Cost JFET Input Operational Amplifiers ADTL/ADTL FEATURES TL/TL compatible Low input bias current: pa maximum Offset voltage 5.5 mv maximum (ADTLA/ADTLA) 9 mv maximum (ADTLJ/ADTLJ) ±5 V operation Low
LM101A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS
LM1A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS LM1A LM201A LM301A INPUT OFFSET VOLTAGE 0.7mV 2mV INPUT BIAS CURRENT 25nA 70nA INPUT OFFSET CURRENT 1.5nA 2nA SLEW RATE AS INVERSINGV/µs V/µs AMPLIFIER
QUAD BILATERAL SWITCH FOR TRANSMISSION OR MULTIPLEXING OF ANALOG OR DIGITAL SIGNALS
QUAD BILATERAL SWITCH FOR TRANSMISSION OR MULTIPLEXING OF ANALOG OR DIGITAL SIGNALS 15V DIGITAL OR ± 7.5V PEAK TO PEAK SWITCHING 125Ω TYPICAL ON RESISTANCE FOR 15V OPERATION SWITCH ON RESISTANCE MATCHED
Ultraprecision Operational Amplifier OP177
Ultraprecision Operational Amplifier FEATURES Ultralow offset voltage TA = 25 C, 25 μv maximum Outstanding offset voltage drift 0. μv/ C maximum Excellent open-loop gain and gain linearity 2 V/μV typical
TL082 Wide Bandwidth Dual JFET Input Operational Amplifier
TL082 Wide Bandwidth Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage
Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from V to V Dual Supply Capability from. V to 8 V Excellent Load Drive
Ultraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
FEATURES Very low voltage noise 2.8 nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage: 2 μv typical Low input offset drift:.6 μv/ C maximum Very high gain:
NI DAQPad -6020E Family Specifications
NI DAQPad -6020E Family Specifications This document lists the I/O terminal summary and specifications for the NI DAQPad-6020E family of devices. This family includes the following devices: NI DAQPad-6020E
16 V, 4 MHz RR0 Amplifiers AD8665/AD8666/AD8668
6 V, MHz RR Amplifiers AD8665/AD8666/AD8668 FEATURES Offset voltage:.5 mv max Low input bias current: pa max Single-supply operation: 5 V to 6 V Dual-supply operation: ±.5 V to ±8 V Low noise: 8 nv/ Hz
Precision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers AD8510/AD8512
a FEATURES Fast Settling Time: 5 ns to.1% Low Offset Voltage: V Max Low TcV OS : 1 V/ C Typ Low Input Bias Current: 25 pa Typ Dual-Supply Operation: 5 V to 15 V Low Noise: 8 nv/ Hz Low Distortion:.5% No
Ultralow Offset Voltage Operational Amplifier OP07
Ultralow Offset Voltage Operational Amplifier OP07 FEATURES Low VOS: 75 μv maximum Low VOS drift:.3 μv/ C maximum Ultrastable vs. time:.5 μv per month maximum Low noise: 0.6 μv p-p maximum Wide input voltage
HA-2520, HA MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers. Features. Applications. Ordering Information
HA-22, HA-22 Data Sheet August, 2 FN2894. 2MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-22/22 comprise a series of operational amplifiers delivering an unsurpassed
Dual, Ultralow Distortion, Ultralow Noise Op Amp AD8599
Dual, Ultralow Distortion, Ultralow Noise Op Amp FEATURES Low noise: 1 nv/ Hz at 1 khz Low distortion: 5 db THD @ khz
Precision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers AD8512
a FEATURES Fast Settling Time: 5 ns to.% Low Offset Voltage: V Max Low TcVos: V/ C Typ Low Input Bias Current: 25 pa Typ Dual-Supply Operation: 5 V to 5 V Low Noise: 8 nv/ Hz Low Distortion:.5% No Phase
Isolated, Linearized Thermocouple Input 5B47 FEATURES APPLICATIONS PRODUCT OVERVIEW
Isolated, Linearized Thermocouple Input 5B47 FEATURES Isolated Thermocouple Input. Amplifies, Protects, Filters, and Isolates Thermocouple Input Works with J, K, T, E, R, S, and B-type thermocouple. Generates
High Voltage Current Shunt Monitor AD8211
High Voltage Current Shunt Monitor AD8211 FEATURES Qualified for automotive applications ±4 V HBM ESD High common-mode voltage range 2 V to +65 V operating 3 V to +68 V survival Buffered output voltage
TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... 2 Specifications... 3 Absolute Maximum
FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew rate: V/μs Short-circuit output current: 2 ma No phase reversal Low input
Features. Parameter Min. Typ. Max. Units. Frequency Range 8 12 GHz GHZ. Input Return Loss* GHZ 10 db
v6.316 MMIC 4-BIT DIGITAL Typical Applications The HMC43LC4B is ideal for: EW Receivers Weather & Military Radar Satellite Communications Beamforming Modules Functional Diagram Features Low RMS Phase Error: