TL081 TL081A - TL081B

Size: px

Start display at page:

Download "TL081 TL081A - TL081B"

Loraine Booker
5 years ago
Views:

1 TL081 TL081A - TL081B GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION HIGH INPUT IMPEDANCE J FET INPUT STAGE INTERNAL FREQUENCY COMPENSATION LATCH UP FREE OPERATION HIGH SLEW RATE : 16V/µs (typ) N DIP8 (Plastic Package) D SO8 (Plastic Micropackage) DESCRIPTION The TL081, TL081A and TL081B are high speed J FET input single operational amplifiers incorporating well matched, high voltage J FET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. PIN CONNECTIONS (top view) ORDER CODE Package Part Number Temperature Range N D TL081M/AM/BM -55 C, +5 C TL081I/AI/BI -40 C, +5 C TL081C/AC/BC 0 C, +70 C Example : TL081CD, TL081IN N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) 1 - Offset null Inverting input 3 - Non-inverting input 4 - V CC Offset null Output 7 - V CC N.C. April /

2 SCHEMATIC DIAGRAM V CC Non-inverting input Inverting input 0 Ω 200 Ω Output 30k 0 Ω 8.2k 1.3k 35k 1.3k 35k 0 Ω V CC Offset Null1 Offset Null2 INPUT OFFSET VOLTAGE NULL CIRCUIT TL081 N1 N2 0k Ω V CC ABSOLUTE MAXIMUM RATINGS Symbol Parameter TL081M, AM, BM TL081I, AI, BI TL081C, AC, BC Unit V CC Supply voltage - note 1) ±18 V V i Input Voltage - note 2) ±15 V V id Differential Input Voltage - note 3) ±30 V P tot Power Dissipation 680 mw Output Short-circuit Duration - note 4) Infinite T oper Operating Free-air Temperature Range -55 to to +5 0 to +70 C T stg Storage Temperature Range -65 to +150 C 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference + level is the midpoint between V CC and V - CC. 2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded 2/

3 ELECTRICAL CHARACTERISTICS V CC = ±15V, (unless otherwise specified) Symbol V io Parameter Input Offset Voltage (R s = 50Ω) T min T amb T max TL081 TL081A TL081B TL081 TL081A TL081B TL081I,M,AC,AI,AM, BC,BI,BM TL081C Min. Typ. Max. Min. Typ. Max DV io Input Offset Voltage Drift µv/ C Input Offset Current - note 1) I io 5 0 T min T amb T max 4 Input Bias Current -note 1 I ib T min T amb T max 20 A vd SVR I CC V icm CMR I os ±V opp SR t r K ov Large Signal Voltage Gain (R L = 2kΩ, V o = ±V) 50 T min T amb T max 25 Supply Voltage Rejection Ratio (R S = 50Ω) 80 T min T amb T max Supply Current, no load T min T amb T max 2.5 Input Common Mode Voltage Range Common Mode Rejection Ratio (R S = 50Ω) 80 T min T amb T max 80 Output Short-circuit Current T min T amb T max Output Voltage Swing T min T amb T max RL = 2kΩ RL = kω RL = 2kΩ RL = kω ± ± Slew Rate () V in = V, R L = 2kΩ, C L = 0pF, unity gain Rise Time () V in = 20mV, R L = 2kΩ, C L = 0pF, unity gain Overshoot () V in = 20mV, R L = 2kΩ, C L = 0pF, unity gain GBP Gain Bandwidth Product () MHz V in = mv, R L = 2kΩ, C L = 0pF, f= 0kHz R i Input Resistance Ω Unit mv pa na na V/mV db ma V db ma V V/µs µs % 3/

4 TL081I,M,AC,AI,AM, TL081C Symbol Parameter BC,BI,BM Unit Min. Typ. Max. Min. Typ. Max. THD Total Harmonic Distortion (), f= 1kHz, R % L = 2kΩ,C L = 0pF, A v = 20dB, V o = 2V pp e n Equivalent Input Noise Voltage nv R S = 0Ω, f = 1KHz Hz m Phase Margin degrees 1. The input bias currents are junction leakage currents which approximately double for every C increase in the junction temperature. 4/

5 VOLTAGE versus FREQUENCY VOLTAGE versus FREQUENCY VOLTAGE versus FREQUENCY VOLTAGE versus FREE AIR TEMP. VOLTAGE versus LOAD RESISTANCE VOLTAGE versus SUPPLY VOLTAGE VOLTAGE (V) R L = kω T amb = +25 C SUPPLY VOLTAGE ( V) 5/

6 INPUT BIAS CURRENT versus FREE AIR TEMPERATURE LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION versus FREE AIR TEMP. INPUT BIAS CURRENT (na) TEMPERATURE ( C) DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V) V O = V R = 2k Ω L TEMPERATURE ( C) LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT versus FREQUENCY TOTAL POWER DISSIPATION versus FREE AIR TEMPERATURE TOTAL POWER DISSIPATION (mw) No signal No load TEMPERATURE ( C) SUPPLY CURRENT PER AMPLIFIER versus FREE AIR TEMPERATURE SUPPLY CURRENT PER AMPLIFIER versus SUPPLY VOLTAGE SUPPLY CURRENT (ma) No signal No load TEMPERATURE ( C) SUPPLY CURRENT (ma) T amb = +25 C No signal No load SUPPLY VOLTAGE ( V) 6/

7 COMMON MODE REJECTION RATIO versus FREE AIR TEMPERATURE VOLTAGE FOLLOWER LARGE SIGNAL PULSE RESPONSE COMMON MODE MODE REJECTION RATIO (db) R L = kω TEMPERATURE ( C) OUTPUT VOLTAGE versus ELAPSED TIME EQUIVALENT INPUT NOISE VOLTAGE versus FREQUENCY OUTPUT VOLTAGE (mv) OVERSHOOT 90% V CC = 15V R % L = 2kΩ T t amb = +25 C r TIME (µs) EQUIVALENT INPUT NOISE VOLTAGE (nv/vhz) A V = R S = 0 Ω T amb = +25 C k 4k k 40k 0k FREQUENCY (Hz) TOTAL HARMONIC DISTORTION versus FREQUENCY TOTAL HARMONIC DISTORTION (%) 1 VV CC 0.4 CC = = 15V 15V AAV V = = 1 1 V V 0.1 O O (rms) (rms) = = 6V 6V T amb T 0.04 amb = = +25 C k 4k k 40k 0k FREQUENCY (Hz) 7/

8 PARAMETER MEASUREMENT INFORMATION Figure 1 : Voltage Follower Figure 2 : Gain-of- Inverting Amplifier k Ω e I 1k Ω - TL081 e o R L C L = 0pF TYPICAL APPLICATIONS (0.5Hz) SQUARE WAVE OSCILLATOR R F = 0k Ω 3.3k Ω - TL V C = 3.3 µf F -15V 3.3k Ω 1k Ω 9.1k Ω f = osc 1 2 x R C F F HIGH Q NOTCH FILTER 8/

9 PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Millimeters Inches Dim. Min. Typ. Max. Min. Typ. Max. A a B b b D E e e e F i L Z /

10 PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) Millimeters Inches Dim. Min. Typ. Max. Min. Typ. Max. A a a a b b C c1 45 (typ.) D E e e F L M S 8 (max.) Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics / 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom

TL082 TL082A - TL082B

TL082 TL082A - TL082B GENERAL PURPOSE J-FET DUAL OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION