General Specifications

Size: px

Start display at page:

Download "General Specifications"

Roy Lee
5 years ago
Views:

1 General pecifications Electrical apacity (Resistive Load) Low Level: 00mA 2V Other Ratings ontact Resistance: Insulation Resistance: ielectric trength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel: Materials & Finishes Plunger/Upper Housing: Lower Housing: Movable ontact: tationary ontacts: witch Terminals: Environmental ata Operating Temperature Range: Humidity: Vibration: hock: Installation ap Installation Force : PB Processing oldering: leaning: tandards & ertifications Flammability tandards: 200 milliohms maximum 00 megohms 250V,000V A minimum between contacts for minute minimum,500v A minimum between contacts & case for minute minimum 5,000,000 operations minimum;,000,000 operations minimum for custom Rectangular witch/ap Assembly (at center of cap) 5,000,000 operations minimum KP0:.9N maximum for Tactile & Nontactile models (at center of cap) KP02:.6N maximum for Tactile, Nontactile & Tactile/Audible models (at center of cap) KP0: Pretravel.22 (3.mm); Overtravel.055 (.4mm); Total Travel.77 (4.5mm) KP02: Pretravel.09 (2.3mm); Overtravel.047 (.2mm); Total Travel.38 (3.5mm) Polyacetal Glass fiber reinforced PBT (UL94V-0) tainless steel with gold plating Gold over copper alloy Brass with tin plating 25 through +50 ( 3 F through +22 F) 90-95% humidity for (04 F) 0 ~ 55Hz with peak-to-peak amplitude of.5mm traversing the frequency range & returning in minute; 3 right angled directions for 2 hours 5G (500m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 50.0N maximum downward force on actuator Wave oldering. ee Profile A in upplement section. Manual oldering: ee Profile A in upplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 lower housing The KP eries pushbuttons have not been tested for UL recognition or A certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. 36

istinctive haracteristics KP series offers a complete switch solution for all broadcast panel needs, including home keys and the custom rectangular switch/cap assembly. istinct, long total travel of.

2 istinctive haracteristics KP series offers a complete switch solution for all broadcast panel needs, including home keys and the custom rectangular switch/cap assembly. istinct, long total travel of.77 (4.5mm) for KP0 or shorter stroke of.38 (3.5mm) for KP02. Available with super bright red/green bicolor LE and RGB LEs. The RGB LE full color spectrum in a switch package provides unlimited color combinations. pecially designed snap-in standoff for simple and secure P board mounting and alignment. Unique actuation guide gives positive indication of circuit transfer as well as smooth and silent operation. (Patent pending). hoices of tactile, nontactile or tactile/audible actuation. ompact design with height of.906 (23.0mm) from P board to top of cap. (ame height as programmable martwitch.) Flat, sculptured or home key square caps in three common sizes for design flexibility in audio/video applications. Twin contacts with gold plating assure high reliability and long life of 5,000,000 operations minimum. Actual ize 37

3 KP Pole & ircuit 5A PT OFF (ON) ( ) = Momentary Normally Open ontacts Travel & Force troke: 4.5mm (.77 ) Actuation Force:.9N troke: 3.5mm (.38 ) Actuation Force:.6N TYPIAL WITH ORERING EXAMPLE 5A N B K G03 6F 2 JB A.6mm Plunger and 5.0mm culptured ap lear Lens and White iffuser PT OFF-Momentary ON ircuit Normally Open ontacts B N N K Housing Plungers Black only 9.2mm Plunger for 2.0mm ap.6mm Plunger for 5.0mm & 7.4mm aps Actuation 0 Tactile Nontactile 02 Tactile Nontactile Tactile/Audible 6F RGB ontacts & Terminals G03 ERIPTION FOR TYPIAL ORERING EXAMPLE KP05ANBKG036F-2JB LEs uper Bright Red/Green Bicolor Red/Green/Blue (ustom) * ee Note Gold ontacts and traight P Terminals; 2V Notes * ustom RGB LE Page 42 ** ustom Rectangular ap Page 43 uper Bright Red/Green Bicolor LE Nontactile Actuation Black Housing Gold ontacts with 00mA Rating traight P Terminals JB F T ap olors lear Lens & White iffuser ap Types Flat culptured Home Key ap izes 2.0mm quare 2 5.0mm quare 3 7.4mm quare ** ee Note 38

4 Pole P G03 Model KP05A KP025A Tactile KP0 or KP02 Plunger Position ( ) = Momentary onnected Terminals Throw & witch chematic Normal own Normal own OFF (ON) ATUATION POLE & IRUIT Normally Open - PT Note: witch terminals & are actually marked on the switch. Gold ontacts traight P Terminals 2V ATTENTION ELETROTATI ENITIVE EVIE LEs are an integral part of the switch and are not available separately. LE circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the upplement section. N Nontactile KP0 or KP02 Tactile/Audible KP02 only ONTAT, TERMINAL, & RATING UPER BRIGHT BIOLOR LE PEIFIATION Amber can be achieved by simultaneous illumination of Red & Green. K HOUING Black only The electrical specifications shown are determined at a basic temperature of 25. (+) OM Green Red ( ) ( ) L olors Red Green Unit Minimum Luminous Intensity I V mcd tandard Luminous Intensity I V mcd Forward Peak urrent I FM 30 (25 for amber) 6F (OM) 25 (22 for amber) ontinuous Forward urrent I F 5 5 ma Forward Voltage V F V Power Peak issipation P mw Reverse Peak Voltage V RM 5 5 V Wavelength at Peak Emission λ 630 ~ ~ 535 nm urrent Reduction Rate Above 25 I F ma/ Ambient Temperature Range 25 ~ +50 ma 39

5 A 2 3 JB 9.2mm Plunger for 2.0mm ap 9.2mm Plunger is designed with a narrower neck to hold the 2.0mm ap. 2.0mm quare F AT3083 Flat ap 5.0mm quare F AT3084 Flat ap 7.4mm quare F AT3085 Flat ap Used on A Plunger Lens & iffuser olors Available: lear/white (2.0) q (6.5).256 (9.2).362 Used on B Plunger Used on B Plunger (7.4) q AP TYPE & OLOR (6.4).252 PLUNGER B AT3078 culptured ap AT3079 culptured ap AT3080 culptured ap.6mm Plunger for 5.0mm & 7.4mm aps.6mm Plunger is designed with a wider neck to hold both the 5.0mm and 7.4mm aps. lear Lens White iffuser T T T (.6).457 AT3086 Home Key ap AT3087 Home Key ap AT3088 Home Key ap Materials & Finishes: Lens - Polycarbonate with glossy finish; iffuser - Polycarbonate with textured finish (2.0) q (6.5).256 (7.4) q Optional Protective Guard AT470 available; contact factory. (2.6) ia.02 (2.6) ia.02 (2.6) ia.02 (2.0) q (6.4).252 (6.5).256 (7.4) q 40

6 (2.0) q (7.4) q (.).043 (6.5).256 (.) (6.4) (5.0).97 (6.4) (6.4).252 (.) (3.6).42 (.5).453 (3.6).42 (.5).453 (3.6).42 (.5).453 (6.0).236 (6.0).236 (6.0).236 TYPIAL WITH IMENION (0.25) (0.25) (0.25).00 (0.37) Typ.05 (0.37) Typ.05 (0.37) Typ.05 OM L OM L OM L (0.6) Typ + (5.08) (0.6) Typ + (5.08) (0.6) Typ + (5.08) (.3) ia Typ.05 (0.9) ia Typ (0.6) ia Typ (.3) ia Typ.05 (0.9) ia Typ (0.6) ia Typ (.3) ia Typ.05 (0.9) ia Typ (0.6) ia Typ L L L.77 (2.54) Typ (2.54) Typ (2.54) Typ mm quare ap KP05AAKG036F-JB 5.0mm quare ap KP05ANBKG036F-2JB 7.4mm quare ap KP05ANBKG036F-3JB 4

The electrical specifications shown are determined at a basic temperature of 25. LEs are an integral part of the switch and are not available separately.

The resistor value can be calculated by using the formula in the upplement ection. Note: For applications that require white illumination, contact factory. 2.

7 The electrical specifications shown are determined at a basic temperature of 25. LEs are an integral part of the switch and are not available separately. LE circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the upplement ection. Note: For applications that require white illumination, contact factory. 2.0mm quare ap with RGB LE KP05AAKG03RGB-JB (2.0) q (6.4) (3.6) mm & 7.4mm quare aps with RGB LE KP05ANBKG03RGB-2JB KP05ANBKG03RGB-3JB (7.4) q.02 (3.8).50 (.).043 (0.2) q Typ.008 (6.5).256 (5.0).97 (.5).453 (4.0) (.).043 (6.4) (3.6) (3.8).50 (0.2) q Typ.008 (.5) (4.0) mm ap UTOM RGB Green ommon Anode (+) Blue olor Red Green Blue Unit Forward Peak urrent I FM ma ontinuous Forward urrent I F ma Forward Voltage V F V Power Peak issipation P mw Reverse Peak Voltage V RM V ominant Wavelength λ d nm urrent Reduction Rate Above 25 IF ma/ Ambient Temperature Range 25 ~ mm ap LE PEIFIATION Red ATTENTION ELETROTATI ENITIVE EVIE TYPIAL WITH IMENION (0.6) Typ G(-) R(-).77 ee Terminal etail (.52) Typ.060 ommon Anode (+) B(-) (0.6) Typ.77 ee Terminal etail (.52) Typ.060 RGB ommon Anode (+) B(-) G(-) R(-) (.3) ia Typ.05 (0.9) ia Typ (0.7) ia Typ.028 Terminal etail (.52) Typ.060 Terminal etail (.3) ia Typ.05 (0.9) ia Typ (0.7) ia Typ.028 (.52) Typ.060 B(-) (+) R(-) G(-) B(-) (+) R(-) G(-).77 (3.8) (3.8).50 42

(34.8).370 (7.4) The electrical specifications shown are determined at a basic temperature of 25. enter LE is an integral part of the switch. LEs are not sold separately.

The resistor value can be calculated by using the formula in the upplement ection. witch/rectangular ap assembly has 3 LEs to achieve bright and even illumination.

8 (34.8).370 (7.4) The electrical specifications shown are determined at a basic temperature of 25. enter LE is an integral part of the switch. LEs are not sold separately. LE circuits are isolated and require an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the upplement ection. witch/rectangular ap assembly has 3 LEs to achieve bright and even illumination. One LE (in center of switch bottom) is an integral part of the switch; the other 2 LEs and 2 LE Holders are packaged separately. UTOM RETANGULAR AP AEMBLY.906 AP AEMBLY IMENION (6.0).236 (3.6).42 (2.54).00 ee below for complete assembly of switch, LEs and LE holders. Forward Peak urrent I FM 30 ma ontinuous Forward urrent I F 20 ma Forward Voltage V F 2.0 V Reverse Peak Voltage V RM 4 V ominant Wavelength λ d 623 nm urrent Reduction Rate Above 25 I F 0.32 ma/ Ambient Temperature Range 25 ~ +50 LE LE Holder (+) (-) olor AEMBLY & INTALLATION INTRUTION witch (3.) ia athode (2.54) (5.9).232 (0.6).02 (4.8).89 LE.77 LE PEIFIATION ontact factory for other LE colors. L+ L (6.7).264 (0.4).409 LE Holder PB (0.45) q Typ.08 witch/rectangular ap Assembly KP05ABKG03JB for Tactile KP05ANBKG03JB for Nontactile Footprint 2 3 (0.9) ia Typ (.3) ia Typ.05 (2.54).00 Red (0.8) ia Typ.03 L+ L.77 Unit Install LE into LE Holder (quantity 2). older LEs and LE Holders into PB. older switch into PB making sure that the two outer LEs and LE Holders clear the bottom side opening of the cap. (2.54).00 (22.86)

9 ATTENTION ELETROTATI ENITIVE EVIE AEMBLY INTRUTION FOR QUARE AP ap Orientation As shown in the accompanying illustration, the cap and plunger are designed with tabs and notches to assure proper orientation of the cap on the switch. Holding the switch tightly, pull the cap off the switch. Once the cap assembly is released from the plunger, the lens and diffuser can be separated. Pry up the lens with fingernail or flat tip screwdriver inserted at the step on the diffuser. After aligning notches with tabs, join the lens and diffuser. Hold the switch tightly without touching the terminals. Firmly press the cap onto the plunger by applying pressure from one side to the other until both are snapped together. Notch Tab tep Plunger Notches Removal of ap Assembly & eparation of Lens & iffuser Installation or Replacement of ap ap Assembly Plunger witch 44

10 (9.8) q.386 (2.0) q (8.28) q.326 (9.8) q.386 Flat ap Lens Flat ap Film Inserts (2.8) q.504 (.28) q.444 (2.8) q.504 (8.97) ia.353 (0.5) ia.43 (8.28)ia.326 (9.8) q.386 LEGEN NKK witches can provide custom legends for caps. ontact factory for more information. Recommended Methods: Laser Etch on clear lens, creen Print, or Pad Print on lens. Laser Print on film insert. Epoxy based ink is recommended. haded areas are suggested printable areas for Lens. (3.4) q.528 (7.4) q haded areas are suggested printable areas for Film Insert. (.88) ia.468 (3.4) q.528 uggested Printable Areas for KP Lens culptured ap Lens (.48) ia.452 (3.0) ia.52 (.28) ia.444 (2.8) q.504 Printing on iffuser is not advisable. uggested Printable Areas for KP Film Insert (3.77) ia.542 (5.3) ia.602 culptured or Home Key ap Film Inserts (.88) ia.468 (3.4) q.528 (2.25) Typ.084 TOP Film Insert Material and Thickness: lear Polyester; 4 mil (00µ) maximum thickness Lens Film Insert iffuser ustom Rectangular ap Lens (30.28).92 (28.75).32 ustom Rectangular Film Insert (33.0).299 (28.75).32 (3.77).542 (5.3).602 (3.77).542 (5.6).64 (0.9) Typ

General Specifications

General Specifications eries W lides Rotaries Programmable Illuminated P Pushbuttons upplement Accessories Indicators General pecifications Electrical apacity (Resistive Load) Power Level: 9A @ 125V A or 6A @ 250V A Other Ratings