Set model No. ESN-T8. 140mm ESN-T mm ESN-T mm ESN-T mm. Light axis interval: 20mm. Smallest detectable object diameter: 30 mm

Transcription

1 series Light urtain Sensors Ultra-thin Slim type of only mm thick and mm wide never affecting work efficiency High-intensity red LED employed Large operation indicator of high-intensity LEDs in series offering superb visibility, may double as work instruction indicator Objects as small as detected utomatic sensitivity compensation feature nti Interference feature llowing adjacent mounting of 2 units for wider range of applications Type Detection method c Throughbeam type High-intensity LEDs in series Light axis interval mm No. of Detecting light axes width 140mm 2mm 0mm 30mm Set model No. ESN-T ESN-T ESN-T ESN-T Operation mode ctivated when light beams of all axes are received Detecting object Opaque object of mm min. *For prices of the transmitter and receiver for separate purchase, see the Price List at the end of this book. Mounting brackets are separately available. See With Mounting racket (Optional) ttached for details. Light axis interval: mm Smallest detectable object diameter: mm mm wide Only mm thick Wide display offers excellent visibility :

2 Rating/Performance/Specification Specification Rating/performance Set model No. model No. model No. ESN-TPN ESN-TL ESN-TRPN ESN-TPN ESN-TL ESN-TRPN ESN-TPN ESN-TL ESN-TRPN ESN-TPN ESN-TL ESN-TRPN Detection method Detection object Light axis interval Through-beam type max. Opaque object of mm min. mm Detecting width 140mm 2mm 0mm 30mm Power supply -24V D ±% / Ripple % max. urrent consumption 0m max. 1m max. 1m max. 1m max. NPN open collector Output mode Rating: sink current 0 m ( VD) max. s with model Nos. ending with -PN have PNP open collector output; source current: 0 m max. Operation mode Response time Light source Light-sensitive element Indicator Material ctivated when light beams of all axes are received (deactivated when light beam of any axis is blocked) 7ms max. Infrared LED (wavelength: 50 nm) Photo I : Power indicator (green LED) / Operation indicator (red LED) : Stable light reception indicator (green LED) / Operation indicator (red LED) ase: S / Indicator window: acrylic onnection Permanently attached cord (Outer dimension: dia.4.3) ord length: 3 m ord: with five 0.2 mm 2 cores, gray (transmitter) or black (receiver) covering Mass 0g max. g max. 0g max. 2g max. uxiliary functions ccessory utomatic sensitivity compensation, nti Mutual Sensitivity feature for adjacent installation, output short circuit protection Operation manual Note: Mounting brackets are separately available. Environmental Specification Environment mbient light 000lx max. mbient temperature 55 (non-freezing) mbient humidity 35-5%RH (non-condensing) Vibration -55 Hz / 1.5 mm amplitude / 2 hours each in 3 directions Protective structure IP40 Dielectric withstanding 00V for 1 minute / between entire live part and case Insulation resistance 500 VD, M. djacent or face-to-face installation of two pairs of sensors will not cause interference. (1) (2) (1) (2) (1) (1) (2) (2)

3 Input/Output ircuit and onnection onnection for nti Interference ord Extension rown: - 24 VD lack: Output lue: 0V Lead color Pink Orange/purple striped The output is provided with short circuit protection. and turns off when the protection feature is activated. Identify and eliminate the cause of the short circuit and turn the power back on. onnection for single-set use purple blue brown pink orange/purple orange/purple pink brown blue black 0VV Synchronization line V 0V MS line Work instruction indicator input haracteristics (Typical Example) output Load Power D - 24V To extend the cord, use wires of at least 0.5 mm2 and limit the length to within 25 m for transmitter and receiver. *1 Parallel displacement characteristics Operating angle characteristics Smallest detectable object diameter characteristics n 2 1 purple blue brown pink orange/purple orange/purple pink brown blue black 0VV Synchronization line V 0V output MS line *2 purple blue brown pink orange/purple orange/purple pink brown blue black 0VV Synchronization line V 0V MS line Sensor (master mode) Work instruction indicator input Sensor (slave mode) n 2 1 Load output Work instruction indicator input 1onnect the MS line (purple) of the transmitter of either () of the two sensors to the ground line (blue), which sets the operation mode of this sensor (Sensor ) to master (M mode). 2onnect the MS line (purple) of the transmitter of the other sensor () to the synchronization line (orange/purple) of Sensor, which sets the operation mode of Sensor to slave (S mode). Note 1When using two sets as a pair, wire so that the operation mode of either of the two will be master and of the other will be slave. Note 2Do not connect the synchronization lines (orange/purple) of Sensors and to each other. Load Power D 24V Horizontal m 4m 3m 2m 1m L Position (mm) Longitudinal L 0 m L L 4m 3m Horizontal Longitudinal 2m 1m 0 Operating angle (degrees) Detection object diameter mm mm L R (transmitter) (midway) (receiver)

4 For orrect Use e sure to follow the instructions in the operation manual provided for correct use of the product. This sensor cannot be used as a press safety device or other safety device for protection of human body that requires conformity to domestic or overseas standards or certification concerning protection of human body. Use for such purposes may lead to death or serious injury in the unlikely event of failure. This sensor is intended for detection of ingress of human body or object passing through an arbitrary point not involving protection of human body or safety. When using this sensor for safety purposes, ensure safe operation of the system as a whole including detection and control. Using Operation Indicator as Work Instruction Indicator Input a flicker signal as a no-voltage contact or NPN transistor open collector input shown as the dotted line in the connection diagram. The indicator blinks in step with the cycle (both transmitter and receiver flicker). When light beam of any axis is blocked, the operation switches to the illuminated state as the operation indicator. Sensor Installation Orientation When installing the sensor, make sure that the ends of the transmitter and receiver with the cord are oriented either upward or downward. The sensor does not function if the transmitter and receiver are not oriented the same way. Sensor Light received Light blocked Indicator ontrol input ON OFF Indicator Operation Illuminated Not illuminated link ontinuous illumination End with cord End with cord Output Operation ON OFF The tightening torque for installing the sensor (with M4 screws) should not exceed 0. Nm. Indicators Indicator operation Name olor Description Power indicator Green Illuminated when power is supplied Operation indicator Red Illuminated when the sensor is activated (light beam of any axis is blocked), turned off when light beams of all axes are received Stable light reception indicator Green Illuminated when the received light intensity level is 1% or more of the operation level Operation indicator Red Illuminated when the sensor is activated (light beam of any axis is blocked), turned off when light beams of all axes are received Indicator arrangement Installation Location ny reflecting object (wall, floor, machine, etc.) within the effective range between the transmitter and receiver may allow the light of the sensor to go around the detection object, which is supposed to block the light, and reach the receiver. hoose the installation location carefully (any glossy object such as stainless steel in the surrounding area must be at least 0 mm away from the center of the light transmission and reception area both vertically (up and down) and horizontally (left and right). Wall, floor, machine, etc. Power indicator (green) Stable light reception indicator (green) shows operation indicator (red); 4 lamps for each unit Irregularly reflected light The operation indicator for ESN-T consists of two lamps (top and bottom). Detection object utomatic sensitivity compensation feature fter the light axis alignment is completed, turn the power off once and back on. The automatic sensitivity compensation feature is enabled and the sensitivity is set at the optimum for the sensor. If the lens is soiled with dirt or dust, the sensitivity is automatically compensated to achieve the optimum sensitivity after the soil is removed. Wall, floor, machine, etc. Irregularly reflected light

5 Dimensions (in mm) m4.3 cord (transmitter/receiver) Dimensions of portions ESN-T ESN-T ESN-T ESN-T

6 With Mounting racket (Optional) ttached (in mm) With mounting bracket model ES-F With mounting bracket model ES-L D D 1. Dimensions of portions Dimensions of portions ESN-T ESN-T ESN-T ESN-T D ESN-T ESN-T ESN-T ESN-T D hole hole Special mounting brackets (optional) ES-F ES-L Description 4 brackets for 1 set (with screws, nuts, washers) 4 brackets for 1 set (with screws, nuts, washers)