WP63SRC T-1 3/4 (5mm) Solid State Lamp

Size: px
Start display at page:

Download "WP63SRC T-1 3/4 (5mm) Solid State Lamp"

Transcription

1 T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS The Super Bright Red source color devices are made with Gallium Aluminum Arsenide Red Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs All devices, equipments and machineries must be electrically grounded PACKAGE DIMENSIONS FEATURES Low power consumption Popular T-1 diameter package General purpose leads Reliable and rugged Long life - solid state reliability Available on tape and reel RoHS compliant APPLICATIONS Status indicator Illuminator Signage applications Decorative and entertainment lighting Commercial and residential architectural lighting 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SELECTION GUIDE Part Number Emitting Color (Material) Lens Type Iv 20mA [2] Viewing Angle [1] Min. Typ. 2θ1/ WP63SRC Super Bright Red (GaAlAs) Water Clear 30 *120 * θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous flux: +/-15%. * Luminous intensity value is traceable to CIE standards Kingbright. All Rights Reserved. Spec No: DSAF2394 / Rev No: V.7A Date: 04/17/2017 Page 1 / 5

2 ELECTRICAL / OPTICAL CHARACTERISTICS at T A =25 C Parameter Symbol Emitting Color Typ. Value Max. Unit Wavelength at Peak Emission I F = 20mA λ peak Super Bright Red nm Dominant Wavelength I F = 20mA λ dom [1] Super Bright Red nm Spectral Bandwidth at 50% Φ REL MAX I F = 20mA Δλ Super Bright Red 20 - nm Capacitance C Super Bright Red 45 - pf Forward Voltage I F = 20mA V F [2] Super Bright Red V Reverse Current (V R = 5V) I R Super Bright Red - 10 ua 1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. ) 2. Forward voltage: ±0.1V. 3. Wavelength value is traceable to CIE standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at T A =25 C Parameter Symbol Value Unit Power Dissipation P D 75 mw Reverse Voltage V R 5 V Junction Temperature T j 115 C Operating Temperature T op -40 to +85 C Storage Temperature T stg -40 to +85 C DC Forward Current I F 30 ma Peak Forward Current I FM [1] 155 ma Electrostatic Discharge Threshold (HBM) V Lead Solder Temperature [2] Lead Solder Temperature [3] 260 C For 3 Seconds 260 C For 5 Seconds 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. 4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity Ref JEDEC/JESD625-A and JEDEC/J-STD Kingbright. All Rights Reserved. Spec No: DSAF2394 / Rev No: V.7A Date: 04/17/2017 Page 2 / 5

3 TECHNICAL DATA RELATIVE INTENSITY vs. WAVELENGTH Red 100% Relative Intensity (a. u.) 80% 60% 40% 20% 0% Wavelength (nm) SPATIAL DISTRIBUTION SUPER BRIGHT RED Forward Current vs. Forward Voltage Luminous Intensity vs. Forward Current Forward Current Derating Curve Luminous Intensity vs. Ambient Temperature Forward current (ma) Forward voltage (V) Luminous intensity normalised at 20mA Forward current (ma) Permissible forward current (ma) Ambient temperature ( C) Luminous intensity normalised at Ta = 25 C Ambient temperature ( C) RECOMMENDED WAVE SOLDERING PROFILE 1. Recommend pre-heat temperature of 105 C or less (as measured with a thermocouple attached to the LED pins) prior to immersion in the solder wave with a maximum solder bath temperature of 260 C 2. Peak wave soldering temperature between 245 C ~ 255 C for 3 sec (5 sec max). 3. Do not apply stress to the epoxy resin while the temperature is above 85 C. 4. Fixtures should not incur stress on the component when mounting and during soldering process. 5. SAC 305 solder alloy is recommended. 6. No more than one wave soldering pass. PACKING & LABEL SPECIFICATIONS 2017 Kingbright. All Rights Reserved. Spec No: DSAF2394 / Rev No: V.7A Date: 04/17/2017 Page 3 / 5

4 PRECAUTIONS Storage conditions 1. Avoid continued exposure to the condensing moisture environment and keep the product away from rapid transitions in ambient temperature. 2. LEDs should be stored with temperature 30 C and relative humidity < 60%. 3. Product in the original sealed package is recommended to be assembled within 72 hours of opening. Product in opened package for more than a week should be baked for 30 (+10/-0) hours at 85 ~ 100 C. LED Mounting Method 1. The lead pitch of the LED must match the pitch of the mounting holes on the PCB during component placement. Lead-forming may be required to insure the lead pitch matches the hole pitch. Refer to the figure below for proper lead forming procedures. Note 1-3: Do not route PCB trace in the contact area between the leadframe and the PCB to prevent short-circuits. " " Correct mounting method " x " Incorrect mounting method 2. When soldering wires to the LED, each wire joint should be separately insulated with heat-shrink tube to prevent short-circuit contact. Do not bundle both wires in one heat shrink tube to avoid pinching the LED leads. Pinching stress on the LED leads may damage the internal structures and cause failure. 3. Use stand-offs (Fig.1) or spacers (Fig.2) to securely position the LED above the PCB. 4. Maintain a minimum of 3mm clearance between the base of the LED lens and the first lead bend (Fig. 3,Fig. 4). 5. During lead forming, use tools or jigs to hold the leads securely so that the bending force will not be transmitted to the LED lens and its internal structures. Do not perform lead forming once the component has been mounted onto the PCB. (Fig. 5 ) 2017 Kingbright. All Rights Reserved. Spec No: DSAF2394 / Rev No: V.7A Date: 04/17/2017 Page 4 / 5

5 Lead Forming Procedures 1. Do not bend the leads more than twice. (Fig. 6 ) 2. During soldering, component covers and holders should leave clearance to avoid placing damaging stress on the LED during soldering. (Fig. 7) 3. The tip of the soldering iron should never touch the lens epoxy. 4. Through-hole LEDs are incompatible with reflow soldering. 5. If the LED will undergo multiple soldering passes or face other processes where the part may be subjected to intense heat, please check with Kingbright for compatibility. PRECAUTIONARY NOTES 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at Kingbright. All Rights Reserved. Spec No: DSAF2394 / Rev No: V.7A Date: 04/17/2017 Page 5 / 5

6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Kingbright: WP63SRC

WP7113SRC/DV T-1 3/4 (5mm) Solid State Lamp

WP7113SRC/DV T-1 3/4 (5mm) Solid State Lamp T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS The Super Bright Red source color devices are made with Gallium Aluminum Arsenide Red Light Emitting Diode Electrostatic discharge and power surge could damage

More information

WP154A4SEJ3VBDZGW/CA T-1 3/4 (5mm) Full Color LED Lamp

WP154A4SEJ3VBDZGW/CA T-1 3/4 (5mm) Full Color LED Lamp T-1 3/4 (5mm) Full Color LED Lamp DESCRIPTIONS The device is based on light emitting diode chip made from AlGaInP The source color devices are made with InGaN Light Emitting Diode The source color devices

More information

WP9294QBC/D 5mm Round LED Lamp

WP9294QBC/D 5mm Round LED Lamp 5mm Round LED Lamp DESCRIPTIONS The Blue source color devices are made with InGaN Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band

More information

WP7113SRSGW T-1 3/4 (5mm) Solid State Lamp

WP7113SRSGW T-1 3/4 (5mm) Solid State Lamp T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS The source color devices are made with Gallium Aluminum Arsenide Red Light Emitting Diode The source color devices are made with Gallium Phosphide Green Light

More information

WP3653SYDLK/SD/TG/J3 Oval LED Lamp

WP3653SYDLK/SD/TG/J3 Oval LED Lamp Oval LED Lamp DESCRIPTIONS The Super Bright Yellow device is based on light emitting diode chip made from AlGaInP Electrostatic discharge and power surge could damage the LEDs It is recommended to use

More information

Kingbright. L-169XID 2 x 3mm Rectangular Solid Lamp DESCRIPTION PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE

Kingbright. L-169XID 2 x 3mm Rectangular Solid Lamp DESCRIPTION PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE 2 x 3mm Rectangular Solid Lamp DESCRIPTION The High Efficiency Red source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode PACKAGE DIMENSIONS FEATURES

More information

Kingbright. L-59SURKSGC T-1 3/4 (5 mm) Bi-Color Indicator Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE

Kingbright. L-59SURKSGC T-1 3/4 (5 mm) Bi-Color Indicator Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE T-1 3/4 (5 mm) Bi-Color Indicator Lamp DESCRIPTIONS The source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The source color devices are made with Gallium Phosphide Green

More information

Kingbright. L-7113SRSGW T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE

Kingbright. L-7113SRSGW T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS The source color devices are made with Gallium Aluminum Arsenide Red Light Emitting Diode The source color devices are made with Gallium Phosphide Green Light

More information

Kingbright. L-1553SYDTK 5 x 5 mm Square Top LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE

Kingbright. L-1553SYDTK 5 x 5 mm Square Top LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE 5 x 5 mm Square Top LED Lamp DESCRIPTIONS The Super Bright Yellow device is made with AlGaInP (on GaAs substrate) light emitting diode chip Electrostatic discharge and power surge could damage the LEDs

More information

WP154A4SUREQBFZGC T-1 3/4 (5mm) Full Color LED Lamp

WP154A4SUREQBFZGC T-1 3/4 (5mm) Full Color LED Lamp T-1 3/4 (5mm) Full Color LED Lamp DESCRIPTIONS The source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The source color devices are made with InGaN Light Emitting Diode The

More information

WP7113LZGCK T-1 3/4 (5mm) Solid State Lamp

WP7113LZGCK T-1 3/4 (5mm) Solid State Lamp T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS The Green source color devices are made with InGaN on Sapphire Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended

More information

Kingbright. L-3VEGW T-1(3mm) Bi-Color Indicator Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE

Kingbright. L-3VEGW T-1(3mm) Bi-Color Indicator Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE T-1(3mm) Bi-Color Indicator Lamp DESCRIPTIONS The source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode The source color devices are made with Gallium

More information

WP937EGW T-1(3mm) Bi-Color Indicator Lamp

WP937EGW T-1(3mm) Bi-Color Indicator Lamp T-1(3mm) Bi-Color Indicator Lamp DESCRIPTIONS The source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode The source color devices are made with Gallium

More information

WP710A10LYD T-1 (3mm) Solid State Lamp

WP710A10LYD T-1 (3mm) Solid State Lamp T-1 (3mm) Solid State Lamp DESCRIPTION The Yellow source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Yellow Light Emitting Diode PACKAGE DIMENSIONS FEATURES Low power consumption

More information

WP59SURKSGC T-1 3/4 (5 mm) Bi-Color Indicator Lamp

WP59SURKSGC T-1 3/4 (5 mm) Bi-Color Indicator Lamp T-1 3/4 (5 mm) Bi-Color Indicator Lamp DESCRIPTIONS The source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The source color devices are made with Gallium Phosphide Green

More information

WP7113VW1C T-1 3/4 (5mm) Solid State Lamp

WP7113VW1C T-1 3/4 (5mm) Solid State Lamp T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS The source color devices are made with InGaN Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist

More information

Kingbright. L-7104SGC T-1 (3mm) Solid State Lamp DESCRIPTION PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE

Kingbright. L-7104SGC T-1 (3mm) Solid State Lamp DESCRIPTION PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE T-1 (3mm) Solid State Lamp DESCRIPTION The Super Bright Green source color devices are made with Gallium Phosphide Green Light Emitting Diode PACKAGE DIMENSIONS FEATURES Low power consumption Popular T-1

More information

Kingbright. L-132XGD T-1 (3mm) Solid State Lamp DESCRIPTION PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE

Kingbright. L-132XGD T-1 (3mm) Solid State Lamp DESCRIPTION PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE T-1 (3mm) Solid State Lamp DESCRIPTION The Green source color devices are made with Gallium Phosphide Green Light Emitting Diode PACKAGE DIMENSIONS FEATURES Low power consumption Popular T-1 diameter package

More information

Kingbright. L-1503SRC-J4 T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE

Kingbright. L-1503SRC-J4 T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE T-1 3/4 (5mm) Solid State Lamp DESCRIPTIONS The Super Bright Red source color devices are made With AlGaInP on Si substrate Light Emitting Diode Electrostatic discharge and power surge could damage the

More information

WP937GYW T-1(3mm) Bi-Color Indicator Lamp

WP937GYW T-1(3mm) Bi-Color Indicator Lamp T-1(3mm) Bi-Color Indicator Lamp DESCRIPTIONS The source color devices are made with Gallium Phosphide Light Emitting Diode The source color devices are made with Gallium Arsenide Phosphide on Gallium

More information

WP36BGD T-1 (3mm) Blinking LED Lamp

WP36BGD T-1 (3mm) Blinking LED Lamp T-1 (3mm) Blinking LED Lamp DESCRIPTIONS The Green source color devices are made with Gallium Phosphide Green Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended

More information

WP56BSRD/B T-1 3/4 (5mm) Blinking LED Lamp

WP56BSRD/B T-1 3/4 (5mm) Blinking LED Lamp T-1 3/4 (5mm) Blinking LED Lamp DESCRIPTIONS The Super Bright Red source color devices are made with Gallium Aluminum Arsenide Red Light Emitting Diode Electrostatic discharge and power surge could damage

More information

Kingbright. L-7679C1QBC-D Super Flux LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS

Kingbright. L-7679C1QBC-D Super Flux LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS Super Flux LED Lamp DESCRIPTIONS The Blue source color devices are made with InGaN Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band

More information

Kingbright. L-115WEYW T-1 (3mm) Bi-Color Indicator Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE

Kingbright. L-115WEYW T-1 (3mm) Bi-Color Indicator Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE T-1 (3mm) Bi-Color Indicator Lamp DESCRIPTIONS The source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode The source color devices are made with

More information

WP710A10F3C T-1 (3mm) Infrared Emitting Diode

WP710A10F3C T-1 (3mm) Infrared Emitting Diode T-1 (3mm) Infrared Emitting Diode DESCRIPTION F3 Made with Gallium Arsenide Infrared Emitting diodes PACKAGE DIMENSIONS FEATURES Mechanically and spectrally matched to the phototransistor RoHS compliant

More information

Kingbright. L-115VGYW-BBTS T-1 (3mm) Bi-Color Indicator Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE

Kingbright. L-115VGYW-BBTS T-1 (3mm) Bi-Color Indicator Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE T-1 (3mm) Bi-Color Indicator Lamp DESCRIPTIONS The source color devices are made with Gallium Phosphide Light Emitting Diode The source color devices are made with Gallium Arsenide Phosphide on Gallium

More information

Kingbright. L-7104GO/1CGK1CGKSYKC T-1 (3mm) Bi-Level Circuit Board Indicator DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION

Kingbright. L-7104GO/1CGK1CGKSYKC T-1 (3mm) Bi-Level Circuit Board Indicator DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION L-714GO/1CGK1CGKSYKC T-1 (3mm) Bi-Level Circuit Board Indicator DESCRIPTIONS The source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The device is made with AlGaInP (on GaAs

More information

Kingbright. L-7113SF6C T-1 3/4 (5mm) Infrared Emitting Diode DESCRIPTION PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE

Kingbright. L-7113SF6C T-1 3/4 (5mm) Infrared Emitting Diode DESCRIPTION PACKAGE DIMENSIONS FEATURES APPLICATIONS SELECTION GUIDE T-1 3/4 (5mm) Infrared Emitting Diode DESCRIPTION SF6 Made with Gallium Aluminum Arsenide Infrared Emitting diodes PACKAGE DIMENSIONS FEATURES Mechanically and spectrally matched to the phototransistor

More information

Kingbright. L-130WCP/1MBN1XGW T-1 (3 mm) Bi-Level Circuit Board Indicator PACKAGE DIMENSIONS

Kingbright. L-130WCP/1MBN1XGW T-1 (3 mm) Bi-Level Circuit Board Indicator PACKAGE DIMENSIONS L-1WCP/1MBN1XGW T-1 (3 mm) Bi-Level Circuit Board Indicator DESCRIPTIONS The source color devices are made with GaN on SiC Light Emitting Diode. The source color devices are made with Gallium Arsenide

More information

Kingbright. L-7679C1SYC-H Super Flux LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS

Kingbright. L-7679C1SYC-H Super Flux LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS Super Flux LED Lamp DESCRIPTIONS This devices are made with TS AlGaInP Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band or anti-electrostatic glove when

More information

APHCM2012SURCK-F x 1.25 mm SMD CHIP LED LAMP

APHCM2012SURCK-F x 1.25 mm SMD CHIP LED LAMP 2.0 x 1.25 mm SMD CHIP LED LAMP DESCRIPTIONS The Hyper Red source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs

More information

SA23-11SRWA 57 mm (2.3 inch) Single Digit Numeric Display

SA23-11SRWA 57 mm (2.3 inch) Single Digit Numeric Display 57 mm (2.3 inch) Single Digit Numeric Display DESCRIPTIONS The Super Bright Red source color devices are made with Gallium Aluminum Arsenide Red Light Emitting Diode Electrostatic discharge and power surge

More information

APTF1616SEEZGQBDC. 1.6 x 1.6 mm Full-Color Surface Mount LED DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE

APTF1616SEEZGQBDC. 1.6 x 1.6 mm Full-Color Surface Mount LED DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE 1.6 x 1.6 mm Full-Color Surface Mount LED DESCRIPTIONS The source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The source color devices are made with InGaN on Sapphire Light

More information

APTD1608LCGCK 1.6 x 0.8 mm SMD Chip LED Lamp

APTD1608LCGCK 1.6 x 0.8 mm SMD Chip LED Lamp 1.6 x.8 mm SMD Chip LED Lamp DESCRIPTIONS The Green source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is

More information

Kingbright. SC10-11SYKWA 26 mm (1.02 inch) Single Digit Numeric Display DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION

Kingbright. SC10-11SYKWA 26 mm (1.02 inch) Single Digit Numeric Display DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION 26 mm (1.2 inch) Single Digit Numeric Display DESCRIPTIONS The Super Bright Yellow device is made with AlGaInP (on GaAs substrate) light emitting diode chip Electrostatic discharge and power surge could

More information

ACDC56-41QBWA/D-F01 Surface Mount Display

ACDC56-41QBWA/D-F01 Surface Mount Display Surface Mount Display DESCRIPTIONS The Blue source color devices are made with InGaN Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist

More information

AAA3528QWDSURKS. 3.5 x 2.8 mm Surface Mount LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE

AAA3528QWDSURKS. 3.5 x 2.8 mm Surface Mount LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE 3.5 x 2.8 mm Surface Mount LED Lamp DESCRIPTIONS The source color devices are made with InGaN Light Emitting Diode The Hyper Red source color devices are made with AlGaInP on GaAs substrate Light Emitting

More information

AAAF3529VBDSEJ3ZGS 3.5 x 2.8 mm Surface Mount SMD Chip LED

AAAF3529VBDSEJ3ZGS 3.5 x 2.8 mm Surface Mount SMD Chip LED 3.5 x 2.8 mm Surface Mount SMD Chip LED DESCRIPTIONS The source color devices are made with InGaN Light Emitting Diode The device is based on light emitting diode chip made from AlGaInP The source color

More information

1.6X1.25mm BI-COLOR SMD CHIP LED LAMP. Descriptions. Features. Package Dimensions

1.6X1.25mm BI-COLOR SMD CHIP LED LAMP. Descriptions. Features. Package Dimensions 1.6X1.25mm BI-COLOR SMD CHIP LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: Features 1.6mmx1.25mm SMD LED, 0.65mm thickness. Bi-color,low power

More information

APHF1608SEEQBDZGKC. 1.6 x 0.8 mm Full-Color Surface Mount LED

APHF1608SEEQBDZGKC. 1.6 x 0.8 mm Full-Color Surface Mount LED APHF168SEEQBDZGKC 1.6 x.8 mm Full-Color Surface Mount LED DESCRIPTIONS The source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The source color devices are made with InGaN

More information

SPEC NO: DSAD0979 REV NO: V.11A DATE: JUL/11/2017 PAGE: 1 OF 5 APPROVED:

SPEC NO: DSAD0979 REV NO: V.11A DATE: JUL/11/2017 PAGE: 1 OF 5 APPROVED: 3.2x1.6mm SMD CHIP LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: AP3216SRCPRV Super Bright Red Features 3.2mmx1.6mm SMD LED, 1.1mm thickness.

More information

SUBMINIATURE SOLID STATE LAMP. Features. Descriptions. Package Dimensions

SUBMINIATURE SOLID STATE LAMP. Features. Descriptions. Package Dimensions SUBMINIATURE SOLID STATE LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: AM2520ZGC09 Green Features Subminiature package. Z-bend lead. Long life -

More information

Kingbright. KAA-3528RGBS-K11-C8-CC 3.5 x 2.8 mm Surface Mount LED Lamp PACKAGE DIMENSIONS

Kingbright. KAA-3528RGBS-K11-C8-CC 3.5 x 2.8 mm Surface Mount LED Lamp PACKAGE DIMENSIONS 3.5 x 2.8 mm Surface Mount LED Lamp DESCRIPTIONS The device is based on light emitting diode chip made from AlGaInP The source color devices are made with InGaN Light Emitting Diode The source color devices

More information

AAA3528AVU/AZGKSYKCT. Single Level Surface Mount CBI DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE

AAA3528AVU/AZGKSYKCT. Single Level Surface Mount CBI DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE Single Level Surface Mount CBI DESCRIPTIONS PACKAGE DIMENSIONS The source color devices are made with InGaN on Sapphire Light Emitting Diode The device is made with AlGaInP (on GaAs substrate) light emitting

More information

AAAF3529LSEEZGKQBKS 3.5 x 2.8 mm Surface Mount SMD Chip LED

AAAF3529LSEEZGKQBKS 3.5 x 2.8 mm Surface Mount SMD Chip LED 3.5 x. mm Surface Mount SMD Chip LED DESCRIPTIONS The source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The source color devices are made with InGaN on Sapphire Light Emitting

More information

3.2mmx3.6mm FULL-COLOR SURFACE MOUNT LED LAMP. Descriptions. Features. Package Dimensions

3.2mmx3.6mm FULL-COLOR SURFACE MOUNT LED LAMP. Descriptions. Features. Package Dimensions 3.2mmx3.6mm FULL-COLOR SURFACE MOUNT LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: APF3236SEEZGKQBKC Features 3.2mmx3.6mm SMD LED, 1.1mm thickness.

More information

AA3528AVU/ACGSK Single Level Surface Mount CBI

AA3528AVU/ACGSK Single Level Surface Mount CBI Single Level Surface Mount CBI DESCRIPTIONS The Green source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It

More information

AAA3528LSEEZGKQBKS 3.5 x 2.8 mm Surface Mount LED Lamp

AAA3528LSEEZGKQBKS 3.5 x 2.8 mm Surface Mount LED Lamp 3.5 x. mm Surface Mount LED Lamp DESCRIPTIONS The source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode The source color devices are made with InGaN on Sapphire Light Emitting

More information

Kingbright. KAAF-3529BGRS x 2.8 mm Surface Mount SMD Chip LED PACKAGE DIMENSIONS

Kingbright. KAAF-3529BGRS x 2.8 mm Surface Mount SMD Chip LED PACKAGE DIMENSIONS 3.5 x 2.8 mm Surface Mount SMD Chip LED DESCRIPTIONS The source color devices are made with InGaN Light Emitting Diode The source color devices are made with InGaN Light Emitting Diode The source color

More information

3.0mmx1.0mm RIGHT ANGLE SMD CHIP LED LAMP. Features. Descriptions. Package Dimensions

3.0mmx1.0mm RIGHT ANGLE SMD CHIP LED LAMP. Features. Descriptions. Package Dimensions 3.0mmx1.0mm RIGHT ANGLE SMD CHIP LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: APA3010ZGC-GX Green Features 3.0x2.0x1.0mm right angle SMD LED,

More information

1.6X1.25mm BI-COLOR SMD CHIP LED LAMP. Descriptions. Features. Package Dimensions

1.6X1.25mm BI-COLOR SMD CHIP LED LAMP. Descriptions. Features. Package Dimensions 1.6X1.25mm BI-COLOR SMD CHIP LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: APTB1612SURKCGKC-F01 Features 1.6mmx1.25mm SMD LED, 0.65mm thickness.

More information

Kingbright. KAAF-5050RGBS mm x 5.0 mm Surface Mount LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE

Kingbright. KAAF-5050RGBS mm x 5.0 mm Surface Mount LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS FEATURES APPLICATIONS ATTENTION SELECTION GUIDE KAAF-RGBS-13 5. mm x 5. mm Surface Mount LED Lamp DESCRIPTIONS The device is based on light emitting diode chip made from AlGaInP The source color devices are made with InGaN Light Emitting Diode The source

More information

Descriptions. Kingbright

Descriptions. Kingbright 2.1x0.6mm RIGHT ANGLE SURFACE LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: KPA-2107QBC-D Blue Features Descriptions 2.1x1.0x0.6mm right angle

More information

SPEC NO: DSAF4499 REV NO: V.4B DATE: APR/12/2016 PAGE: 1 OF 5 APPROVED:

SPEC NO: DSAF4499 REV NO: V.4B DATE: APR/12/2016 PAGE: 1 OF 5 APPROVED: T-1 (3mm) RIGHT ANGLE LED INDICATOR ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: WP934EW/MBD Blue Features Pre-trimmed leads for pc mounting. Black

More information

AA2214VR4D1S-C1 2.2 x 1.4 mm Surface Mount LED Lamp

AA2214VR4D1S-C1 2.2 x 1.4 mm Surface Mount LED Lamp 2.2 x 1.4 mm Surface Mount LED Lamp DESCRIPTIONS The source color devices are made with InGaN Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use

More information

3.4mm RIGHT ANGLE LED INDICATOR. Features. Description. Package Dimensions. Part Number: WP138A8QMP/GD/TG

3.4mm RIGHT ANGLE LED INDICATOR. Features. Description. Package Dimensions. Part Number: WP138A8QMP/GD/TG 3.4mm RIGHT ANGLE LED INDICATOR Part Number: WP138A8QMP/GD/TG Green Features Surface mount type. Black case enhances contrast ratio. Wide viewing angle. High reliability life measured in years. Package:1000pcs

More information

Descriptions. The Hyper Red source color devices are made with Suitable for all SMD assembly and solder process.

Descriptions. The Hyper Red source color devices are made with Suitable for all SMD assembly and solder process. 4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED LAMP Part Number: Hyper Red ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions Single color. The Hyper Red

More information

2.5x0.7mm RIGHT ANGLE SMD CHIP LED LAMP. Features. Descriptions. Package Dimensions

2.5x0.7mm RIGHT ANGLE SMD CHIP LED LAMP. Features. Descriptions. Package Dimensions 2.5x0.7mm RIGHT ANGLE SMD CHIP LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: APFA2507LSURKSYKZGKC Features 2.5x1.0x0.7mm right angle SMD LED,

More information

Descriptions. The Hyper Red device is based on light emitting diode Ideal for backlight and indicator.

Descriptions. The Hyper Red device is based on light emitting diode Ideal for backlight and indicator. 3.0x1.0mm RIGHT ANGLE SMD CHIP LED LAMP Part Number: KPFA-3011BZ1RGZ1C-132/F ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Blue Hyper Red Green Features Descriptions

More information

AA3528VRVFS/A 3.5 x 2.8 mm Surface Mount LED Lamp

AA3528VRVFS/A 3.5 x 2.8 mm Surface Mount LED Lamp 3.5 x 2.8 mm Surface Mount LED Lamp DESCRIPTIONS The source color devices are made with InGaN Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use

More information

SPEC NO: DSAH3723 REV NO: V.5B DATE: AUG/19/2014 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED:

SPEC NO: DSAH3723 REV NO: V.5B DATE: AUG/19/2014 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: 3x2.4mm SMD CHIP LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: AP23QBC/D/F-F01 Blue Features 3mmx2.4mm SMT LED, 1.05mm thickness. Low power

More information

Descriptions. Kingbright

Descriptions. Kingbright 3.5x2.8mm SURFACE MOUNT LED LAMP Part Number: Features Both chips can be controlled separately. Suitable for all SMD assembly and solder process. Available on tape and reel. Package: 2000pcs / reel. Moisture

More information

2.0x1.25 mm INFRARED EMITTING DIODE. Features. Description. Package Dimensions. Part Number: APT2012SF4C-PRV

2.0x1.25 mm INFRARED EMITTING DIODE. Features. Description. Package Dimensions. Part Number: APT2012SF4C-PRV 2.0x1.25 mm INFRARED EMITTING DIODE Part Number: APT2012SF4C-PRV Features 2.0mmx1.25mm SMD LED,0.75mm thickness. Mechanically and spectrally matched to the phototransistor. Package: 2000pcs / reel. Moisture

More information

Description. Kingbright

Description. Kingbright 3.0mmx1.0mm RIGHT ANGLE SMD CHIP LED LAMP Part Number: Super Bright Orange Features 3.0mmx1.0mm right angle SMD LED, 2.0mm thickness. Low power consumption. Wide viewing angle. Ideal for back light and

More information

1.6x0.8x0.5mm BI-COLOR SURFACE MOUNT LED. Descriptions. Features. Package Dimensions

1.6x0.8x0.5mm BI-COLOR SURFACE MOUNT LED. Descriptions. Features. Package Dimensions 1.6x0.8x0.5mm BI-COLOR SURFACE MOUNT LED ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: APHB1608ZGSYKC Features 1.6mmX0.8mm SMD LED, 0.5mm thickness.

More information

2.1x0.6mm RIGHT ANGLE SURFACE LED LAMP PRELIMINARY SPEC. Descriptions. Features. Package Dimensions

2.1x0.6mm RIGHT ANGLE SURFACE LED LAMP PRELIMINARY SPEC. Descriptions. Features. Package Dimensions 2.1x0.6mm RIGHT ANGLE SURFACE LED LAMP PRELIMINARY SPEC ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: APA2107LZGCK Green Features 2.1mmX0.6mm right angle

More information

T-1 3/4 (5mm) FULL COLOR LED LAMP. Features. Descriptions. Package Dimensions

T-1 3/4 (5mm) FULL COLOR LED LAMP. Features. Descriptions. Package Dimensions T-1 3/4 (5mm) FULL COLOR LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: WP154A4SEJ3VBDZGC/CA Features Uniform light output. Low power consumption.

More information

3.5x2.8mm SURFACE MOUNT LED LAMP. Features. Description. Package Dimensions

3.5x2.8mm SURFACE MOUNT LED LAMP. Features. Description. Package Dimensions 3.5x2.8mm SURFACE MOUNT LED LAMP Part Number: AA3528MGC Mega Green Features Single color. Suitable for all SMD assembly and solder process. Available on tape and reel. Ideal for backlighting. Package :

More information

Descriptions. Kingbright

Descriptions. Kingbright T-1 3/4 (5mm) BI-COLOR CYLINDRICAL LED LAMP Part Number: L-489EGWT Features Cylindrical type. Low power consumption. 3 leads with one common lead. Long life - solid state reliability. Reliable and rugged.

More information

1.0X0.5X0.2mm (0402)SMD CHIP LED LAMP. Features. Description. Package Dimensions. Part Number: APG1005CGC-T

1.0X0.5X0.2mm (0402)SMD CHIP LED LAMP. Features. Description. Package Dimensions. Part Number: APG1005CGC-T 1.0X0.5X0.2mm (0402)SMD CHIP LED LAMP Part Number: APG1005CGC-T Green Features 1.0mmX0.5mm SMD LED, 0.2mm thickness. Low power consumption. Wide viewing angle. Compatible with automatic placement equipment.

More information

SURFACE MOUNT DISPLAY. Features. Description. Package Dimensions& Internal Circuit Diagram

SURFACE MOUNT DISPLAY. Features. Description. Package Dimensions& Internal Circuit Diagram SURFACE MOUNT DISPLAY Part Number: ACSC03-41SRWA-F01 Super Bright Red Features 0.3 inch digit height. Low current operation. Excellent character appearance. Mechanically rugged. Gray face,white segment.

More information

Descriptions. Kingbright

Descriptions. Kingbright SURFACE MOUNT DISPLAY ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: KCSA39-136 Blue Features 0.39 inch digit height. Low current operation. Excellent

More information

SPEC NO: DSAF1339 REV NO: V.9B DATE: NOV/10/2015 PAGE: 1 OF 6 APPROVED:

SPEC NO: DSAF1339 REV NO: V.9B DATE: NOV/10/2015 PAGE: 1 OF 6 APPROVED: 3.2x2.4mm SMD CHIP LED LAMP Part Number: APBD3224SYKCGKC-F01 Features 3.2x2.4mm SMD LED, 2.4mm thickness. Low power consumption. Ideal for backlight and indicator. Package : 1500pcs / reel. Moisture sensitivity

More information

1.9x3.9mm RECTANGULAR SOLID LAMP. Features. Description. Package Dimensions. Part Number: WP144GDT

1.9x3.9mm RECTANGULAR SOLID LAMP. Features. Description. Package Dimensions. Part Number: WP144GDT 1.9x3.9mm RECTANGULAR SOLID LAMP Part Number: WP144GDT Green Features Low power consumption. Reliable and rugged. Excellent uniformity of light output. Suitable for level indicator. Long life - solid state

More information

SUBMINIATURE SOLID STATE LAMP. Features. Description. Package Dimensions

SUBMINIATURE SOLID STATE LAMP. Features. Description. Package Dimensions SUBMINIATURE SOLID STATE LAMP Part Number: AM2520EC03 High Efficiency Red Features Subminiature package. Gull wing lead. Long life - solid state reliability. Low package profile. Moisture sensitivity level

More information

SPEC NO: DSAN1915 REV NO: V.1A DATE: AUG/30/2013 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED:

SPEC NO: DSAN1915 REV NO: V.1A DATE: AUG/30/2013 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: T-1 (3mm) SOLID STATE LAMP Part Number: L-1154SRC-J4 Super Bright Red Features Low power consumption. Popular T-1 diameter package. General purpose leads. Reliable and rugged. Long life - solid state reliability.

More information

Description. Kingbright

Description. Kingbright 3.0mmx1.5mm SMD CHIP LED LAMP Part Number: KPL-3015CGCK Green Features 3.0mmx1.5mm SMD LED, 1.4mm thickness. Low power consumption. Ideal for backlight and indicator. Package : 2000pcs / reel. Moisture

More information

SOT-23 SURFACE MOUNT LED LAMP. Features. Description. Package Dimensions. Part Number: KM-23LYD

SOT-23 SURFACE MOUNT LED LAMP. Features. Description. Package Dimensions. Part Number: KM-23LYD SOT-23 SURFACE MOUNT LED LAMP Part Number: KM-23LYD Yellow Features SOT-23 package surface mount LED lamp. Low power consumption. Long life - solid state reliability. Package: 2000pcs / reel. Moisture

More information

7.6mmX7.6mm SUPER FLUX LED LAMP. Features. Descriptions. Package Dimensions

7.6mmX7.6mm SUPER FLUX LED LAMP. Features. Descriptions. Package Dimensions 7.6mmX7.6mm SUPER FLUX LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: L-7676CZGC-G Green Features Super flux output. Design for high current

More information

Description. Kingbright

Description. Kingbright T-1 3/4 (5mm) SOLID STATE LAMP Part Number: L-7113LYD Yellow Features Description Low power consumption. Popular T-1 3/4 diameter package. General purpose leads. Reliable and rugged. Long life - solid

More information

SPEC NO: DSAF1341 REV NO: V.7B DATE: AUG/20/2014 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED:

SPEC NO: DSAF1341 REV NO: V.7B DATE: AUG/20/2014 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: 2.0x1.25mm SMD CHIP LED LAMP Part Number: APHCM2012CGCK-F01 Green Features 2.0X1.25mm SMT LED,0.5mm max. thickness. Low power consumption. Wide viewing angle. Ideal for backlight and indicator. Package

More information

Description. Kingbright

Description. Kingbright T-1 (3mm) SOLID STATE LAMP Part Number: L-7104ID High Efficiency Red Features Low power consumption. Popular T-1 diameter package. General purpose leads. Reliable and rugged. Long life - solid state reliability.

More information

Description. Kingbright

Description. Kingbright 14.22mm (0.56INCH) SINGLE DIGIT NUMERIC DISPLAY Part Number: SC56-11CGKWA Green Features 0.56 inch digit height. Low current operation. Excellent character appearance. Easy mounting on P.C. boards or sockets.

More information

SINGLE LEVEL SURFACE MOUNT CBI. Descriptions. Features. Package Dimensions. Recommended Soldering Pattern

SINGLE LEVEL SURFACE MOUNT CBI. Descriptions. Features. Package Dimensions. Recommended Soldering Pattern SINGLE LEVEL SURFACE MOUNT CBI Part Number: AAA3528AVU/ARBGS-112 ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Surface mount type. Compatible with automatic

More information

Description. Kingbright

Description. Kingbright T-1 3/4 (5mm) SOLID STATE LAMP Part Number: L-63GD Green Features Low profile. Low power consumption. Long life - solid state reliability. Reliable and rugged. RoHS compliant. Description The Green source

More information

Description. Kingbright

Description. Kingbright 2x5mm RECTANGULAR LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: L-9763PBDT-A Blue Features Low power consumption. Reliable and rugged. Excellent

More information

SPEC NO: DSAF1859 REV NO: V.9B DATE: APR/14/2015 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED:

SPEC NO: DSAF1859 REV NO: V.9B DATE: APR/14/2015 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: T-1 (3mm) RIGHT ANGLE LED INDICATOR Part Number: WP934RS/GD Green Features Pre-trimmed leads for pc mounting. Pillars are designed for positioning the housing on P.C. board. Black case enhances contrast

More information

Descriptions. Kingbright

Descriptions. Kingbright T-1 3/4 (5mm) BI-COLOR INDICATOR LAMP Part Number: L-59GYW Features Uniform light output. Low power consumption. 3 leads with one common lead. Long life-solid state reliability. RoHS compliant. Descriptions

More information

SPEC NO: DSAB8533 REV NO: V.19A DATE: AUG/16/2014 PAGE: 1 OF 7 APPROVED: WYNEC CHECKED:

SPEC NO: DSAB8533 REV NO: V.19A DATE: AUG/16/2014 PAGE: 1 OF 7 APPROVED: WYNEC CHECKED: T-1 3/4 (5mm) BI-COLOR INDICATOR LAMP Part Number: L-59SURKCGKW Features Uniform light output. Low power consumption. 3 leads with one common lead. Long life-solid state reliability. RoHS compliant. Descriptions

More information

Description. Kingbright

Description. Kingbright 20 SEGMENTS BAR GRAPH ARRAY Part Number: DC-20/20SURKWA Hyper Red Features Suitable for level indicators. Low current operation. Excellent on/off contrast. End stackable. Mechanically rugged. Different

More information

Description. Kingbright

Description. Kingbright T-1 3/4 (5mm) BI-COLOR INDICATOR LAMP Part Number: L-59EGW Features Uniform light output. Low power consumption. 3 leads with one common lead. Long life-solid state reliability. High glass transition temperature

More information

Description. Kingbright

Description. Kingbright 1.6X0.8mm SMD CHIP LED LAMP Part Number: Green Features 1.6mmX0.8mm SMT LED, 1.1mm thickness. Low power consumption. Wide viewing angle. Ideal for backlight and indicator. Package: 2000pcs / reel. Moisture

More information

SPEC NO: DSAN4362 REV NO: V.1A DATE: JAN/10/2014 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED:

SPEC NO: DSAN4362 REV NO: V.1A DATE: JAN/10/2014 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: 1.6X0.8mm SMD CHIP LED LAMP Part Number: Hyper Red Features 1.6mmX0.8mm SMT LED, 1.06mm thickness. Low power consumption. Wide viewing angle. Ideal for backlight and indicator. Various colors and lens

More information

Description. Kingbright

Description. Kingbright T-1 (3mm) CYLINDRICAL LED LAMP Part Number: L-424YDT Yellow Features Cylindrical type. Low power consumption. Reliable and rugged. Long life - solid state reliability. Available on tape and reel. RoHS

More information

Descriptions. Kingbright

Descriptions. Kingbright T-1(3mm) BI-COLOR INDICATOR LAMP Part Number: L-3VEYW Features Uniform light output. Low power consumption. 3 leads with one common lead. Long life - solid state reliability. RoHS compliant. Descriptions

More information

1.6X1.25mm BI-COLOR SMD CHIP LED LAMP. Features. Description. Package Dimensions. Part Number: KPTB-1612SURKCGKC. Hyper Red Green

1.6X1.25mm BI-COLOR SMD CHIP LED LAMP. Features. Description. Package Dimensions. Part Number: KPTB-1612SURKCGKC. Hyper Red Green 1.6X1.25mm BI-COLOR SMD CHIP LED LAMP Part Number: KPTB-1612SURKCGKC Features 1.6mmx1.25mm SMT LED, 0.65mm thickness. Bi-color,low power consumption. Wide viewing angle. Ideal for backlight and indicator.

More information

Description. Kingbright

Description. Kingbright 2mm x 5mm BI-COLOR RECTANGULAR LED LAMP Part Number: L-117EGWT Features Uniform light output. Suitable for level indicator. Low power consumption. Long life - solid state reliability. RoHS compliant. Description

More information

Descriptions. Kingbright

Descriptions. Kingbright 38.1mm (1.5INCH) SINGLE DIGIT NUMERIC DISPLAY Part Number: SBA15-11SURKCGKWA Features 1.5 inch digit height. Low current operation. Excellent character appearance. High light output. Easy mounting on P.C.

More information

SPEC NO: DSAA3955 REV NO: V.12A DATE: AUG/11/2014 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED:

SPEC NO: DSAA3955 REV NO: V.12A DATE: AUG/11/2014 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: 7.6mmX7.6mm SUPER FLUX LED LAMP Part Number: L-7676CSURC-E Hyper Red Features Super flux output. Design for high current operation. Outstanding material efficiency. Reliable and rugged. RoHS compliant.

More information

Description. Kingbright

Description. Kingbright 1.6X0.8mm INFRARED EMITTING DIODE Part Number: KP-1608F3C Features 1.6mmX0.8mm SMT LED, 1.1mm thickness. Mechanically and spectrally matched to the phototransistor. Package: 2000pcs / reel. Moisture sensitivity

More information