A B C D E F G H REVISIONS NOTES: KP PRESS-FIT INSTALLATIONS ARE SHOWN UNLESS OTHERWISE SPECIFIED.

Transcription

1 A B C E F G H ISIONS NOTES: ESCRIPTION BY. THIS OCUMENT CONTROLS INSTALLATION OF INFOCHIP URAPLUG 9. UHF RFI TAG PROUCTS IN THE FOLLOWING PRESS-FIT INSTALLATION TYPES: "NEAR-FLUSH" AN "RECESSE". AHESIVE INSTALLATIONS ARE ETAILE AT THE EN OF THIS RAWING. 0 AE EXAMPLES TO CLARIFY MOUNTING WITH PREFERRE POLARIZATION. CLARIFIE SPOT-FACE EPTH. UP PRIMARY BORE IAMETER TOLERANCE. AE CORROSION INHIBITOR APPLICATION NOTE KP PRESS-FIT INSTALLATIONS ARE SHOWN UNLESS OTHERWISE SPECIFIE. 0 AE SHEET ETAILING AHESIVE INSTALLSF KP. URAPLUG 9. UHF MUST BE INSTALLE INTO METALLIC ASSETS. FOR MAXIMUM REA RANGE, ESPECIALLY WHEN TAGGING SMALLER ASSETS, THE P9. POSITION AN ORIENTATION ON THE ASSET SHOUL BE AS SPECIFIE BELOW ON THIS SHEET.... IT IS THE CUSTOMER RESPONSIBILITY TO ENSURE THAT THE INSTALLE LOCATION OF THE URAPLUG EVICE ON THE ASSET WILL PERMIT THE TAG TO BE SCANNE BY ANY RFI REAERS ESIRE FOR USE BY THE CUSTOMER. IT IS THE CUSTOMER RESPONSIBILITY TO ENSURE THAT THE TARGET ASSET MAINTAINS SUFFICIENT STRUCTURAL INTEGRITY AFTER RILLING AN INSTALLATION OF THE URAPLUG 9. UHF EVICE. ASSETS SHOWN IN THIS RAWING ARE ARBITRARY AN ARE SHOWN FOR EXAMPLE REFERENCE ONLY. FLAT ASSET TOP SURFACES ARE SHOWN FOR SIMPLICITY BUT INSTALLATIONS TO CURVE SURFACES SUCH AS PIPE O IS ACCEPTABLE. INFOCHIP REQUIRES THE USE OF CUSTOM INFOCHIP-SUPPLIE RILL BITS TO ENSURE THE RILLE HOLES EXHIBIT THE CRITICAL FEATURES AN ACCURACY NEEE FOR A RELIABLE PRESS-FITTE INSTALLATION. BITS FOR URAPLUG 9. UHF ARE CURRENTLY OFFERE IN VERSIONS BASE ON THE INSTALLATION TYPE. RILL BIT PART NUMBERS ARE CLEARLY MARKE ON EACH BIT. "NEAR FLUSH" INSTALL EXAMPLE. INFOCHIP REQUIRES THE USE OF A CUSTOM INFOCHIP-SUPPLIE TOOL (HOLETOOL-9.) FOR ANY INSTALLATIONS TO BE USE IN SEVERE ENVIRONMENTS WHICH WILL NEE INCREASE PRESS-FIT RETENTION. THE HOLETOOL-9. F IS A BASIC HAN-OPERATE TOOL USE TO A AN UNERCUT TO THE RILLE HOLE BEFORE PRESS-FITTING.. INFOCHIP RECOMMENS THE USE OF MILLING MACHINE WITH A COLLET-TYPE CHUCK TO ENSURE HIGH RIGIITY WITH MINIMAL RUNOUT. A "RILL-CHUCK" SHOUL NOT BE USE. A COLLET CHUCK TO BE USE SHOUL BE VERIFIE BY IAL INICATOR WITH A TOTAL INCLUE RUNOUT OF LESS THAN 0.0MM (0.000"). HAN RILLS CANNOT BE USE. UNLESS PRE-AUTHORIZE BY INFOCHIP, ANY RILLING AN INSTALLATION METHOS OTHER THAN THOSE SPECIFIE ON THIS RAWING WILL VOI ANY WARRANTIES.. 9. INFOCHIP RECOMMENS THAT THE RILLING SHOUL FOLLOW EFFECTIVE MACHINING PRACTICES (SPEES/FEES, COOLANT) FOR THE SPECIFC ASSET METAL AN HARNESS TO ENSURE MAXIMUM LIFE OF THE RILLING TOOLS AN ACCURACY OF THE RILLE HOLE. PRESS-FITTING OF THE URAPLUG 9. UHF SHOUL BE CARRIE OUT AS ETAILE ON THIS RAWING TO ENSURE IT IS NOT AMAGE URING THE INSERTION. NARROW IMENSION 0. THIS RAWING IS TO BE PRINTE IN FULL COLOR AS SOME VIEWS ARE COLORE FOR VISUAL CLARITY. ASSET SURFACES SHOWN IN GREY COLOR ARE FORME BY THE RILLING PROCESS.. INSTALLATION PROCEURE FOR "NEAR-FLUSH" INSTALL IS SHOWN ON SHEET. INSTALLATION PROCEURE FOR "RECESSE" INSTALL IS SIMILAR AN IS NOT SHOWN ON THIS RAWING. VENT NOTCH EXPLANATION OF MOUNTING TAG WITH PREFERRE ORIENTATION (POLARIZATION) APPLICABLE FOR SMALL OR SLENER ITEMS INCLUING TUBULAR ITEMS BEST RANGE PREFERRE MOUNTING FOR MAXIMUM REA RANGE ASHE LINE IS AS LONG AS POSSIBLE, ALIGNE WITH LONG IMENSION OF PART VENT NOTCH FACES 0 EG AWAY FROM ASHE LINE LONG IMENSION VENT (NOTCH) OK (REA RANGE WILL BE CLOSE TO BEST) ASHE LINE IS AS LONG AS POSSIBLE, ALIGNE WITH LONG IMENSION OF PART VENT NOTCH FACES 0 EG AWAY FROM ASHE LINE NARROW IMENSION REUCE (REA RANGE WILL BE REUCE) AVOI THIS IF POSSIBLE ASHE LINE IS AS LONG AS POSSIBLE, ALIGNE WITH LONG IMENSION OF PART VENT NOTCH FACES 90 EG AWAY FROM ASHE LINE REUCE (REA RANGE WILL BE REUCE) AVOI THIS IF POSSIBLE ASHE LINE IS AS LONG AS POSSIBLE, ALIGNE WITH LONG IMENSION OF PART VENT NOTCH FACES EG AWAY FROM ASHE LINE LONG IMENSION "RECESSE" INSTALL EXAMPLE ETAILING TAG POSITION AN ORIENTATION OK (REA RANGE WILL BE CLOSE TO BEST) TAG IS MOUNTE IN THE MILE OF THE PART VENT NOTCH FACES 0/0 EG AWAY FROM ASHE LINE OCUMENT CONTAINS INFOCHIP INFORMATION AN SHALL NOT BE REPROUCE OR ISCLOSE TO THIR PARTIES WITHOUT PRIOR RAWN CHECKE APPROVE KP ALL IMENSIONS ARE: [INCH] UNLESS OTHERWISE SPECIFIE. TOLERANCES ON LINEAR IMENSIONS 0.0 UNLESS OTHERWISE SPECIFIE WG. SIZE Install REF - uraplug 9. UHF uraplug 9. UHF of 0

2 A B C E F G H R0..00 ENTRY RAIUS CRITICAL FEATURE FOR PRESS-FIT A A R0..0 CRITIAL FEATURE FOR PRESS-FIT OVERALL LENGTH ETAIL C 9 : SPOT FACE REFERENCE NEAR-FLUSH ASSET (GREY SURFACES ARE CREATE BY RILLING) B R ±0.0.0±.00 PRIMARY BORE.. EFFECTIVE HOLE EPTH 0.0±0.0.0±.0 SPOT FACE C.00. R SECTION A-A.. OVERALL EPTH EXAMPLE OF "BIT-9.-F" CONFIGURATION : NOTES: A MOEL OF THE FLUSH RILL BIT IS SHOWN ON THE LEFT OF THIS PAGE FOR REFERENCE (RILL FLUTES ARE NOT SHOWN). THE BIT IS ESIGNE TO BE USE IN A PLUNGE OPERATION (AS A RILL BIT) IN A MILLING MACHINE. THE BIT IS A -FLUTE HELICAL TYPE CUTTER, GROUN TO INFOCHIP SPECIFICATION FROM SOLI MICRO-GRAIN CARBIE. BITS ARE COATE WITH TITANIUM NITRIE. BITS ARE TO HAVE PERMANENT MARKINGS AS SHOWN IN THE RAWING VIEW ON THIS SHEET, INCLUING THE ESIGN ISION AS SHOWN. BITS ARE TO BE INIVIUALLY PACKAGE AN CUTTING EN SHOUL BE PROTECTE. THE EPTH OF THE "SPOT-FACE" FEATURE IS TO BE ETERMINE BY THE CUSTOMER. IT IS CONTROLLE BY AJUSTING THE RILLING EPTH. INFOCHIP RECOMMENS TO USE A MINIMAL EPTH FOR THE "SPOT-FACE" FEATURE FOR BEST REAING RANGE, WHERE AITIONAL IMPACT PROTECTION IS NOT NEEE. A MAXIMUM SPOT-FACE OF ABOUT 0. CAN BE USE WITH THE "FLUSH" BIT FOR INSTALLATIONS REQUIRING AITIONAL IMPACT PROTECTION, WHERE SOME REUCTION IN REA RANGE IS PERMITTE. THIS RAWING SHOWS AN ARBITRARY SPOT-FACE. IF RILLING WITHOUT PROUCING A VISIBLE SPOT FACE FEATURE, ENSURE THAT SUFFICIENT HOLE EPTH IS ACHIEVE TO ENSURE THE ENTRY RAIUS FEATURE LABELE "CRITICAL FEATURE FOR PRESS-FIT" IS FULLY FORME. INFOCHIP RECOMMENS TO ENSURE THAT THE SPOT-FACE FEATURE IS VISIBLE TO ENSURE THAT THE CRITICAL ENTRY RAIUS FEATURE IS PRESENT. EFFECTIVE HOLE EPTH TOLERANCE IS ENSURE BY THE USE OF INFOCHIP "NEAR-FLUSH" BIT PROVIE THAT THE RILLING EPTH IS SUFFICIENT TO PROUCE A VISIBLE "SPOT-FACE" FEATURE. THE "NEAR-FLUSH" BITS ARE TYPICALLY USE FOR INSTALLATION ON FLAT ASSET SURFACES. IT IS ALSO ACCEPTABLE FOR INSTALLATION TO ASSETS WITH CONVEX CURVATURE WHERE THE RAIUS OF CURVATURE IS A MINIMUM OF APPROXIMATELY 0. INCHES. AS AN EXAMPLE, THE NEAR-FLUSH BIT CAN BE USE FOR INSTALLATIONS ON A PIPE MEASURING INCHES IN OUTER IAMETER. INFOCHIP RECOMMENS THAT THE CRITICAL PRIMARY BORE (LOWER) BE MEASURE AFTER RILLING TO ENSURE A PROPER PRESS-FIT. SUGGESTE MEASURE BORES ARE SHOWN IN ETAIL B ON THIS SHEET. THE LOWER BORE IAMETER CAN BE MEASURE USING A HALF-BALL TYPE HOLE GAUGE ALONG WITH A MICROMETER.F..9 SPOT FACE 9.. ETAIL B : COUNTERBORE ETAILING "NEAR-FLUSH" ASSETS (PRESS-FIT) OCUMENT CONTAINS INFOCHIP INFORMATION AN SHALL NOT BE REPROUCE OR ISCLOSE TO THIR PARTIES WITHOUT PRIOR RAWN CHECKE APPROVE KP ALL IMENSIONS ARE: UNLESS OTHERWISE SPECIFIE. TOLERANCES ON LINEAR IMENSIONS ARE 0.0 UNLESS OTHERWISE SPECIFIE WG. SIZE Install REF - uraplug 9. UHF uraplug 9. UHF of 0

3 A B C E F G H.. R0..00 R R OVERALL LENGTH E CONICAL RECESS ETAIL H 0 : REFERENCE RECESSE ASSET (GREY SURFACES ARE CREATE BY RILLING) EXAMPLE TOP COUNTERSINK 0.. VIRTUAL SHARPS 9.0±0.0.0±.00 PRIMARY BORE SECTION - :.90. EXAMPLE RECESS EPTH.. MAXIMUM THEORETICAL RECESS NOTES: EXAMPLE OF "BIT-9.-R" CONFIGURATION R0..00 H.. RILL SHOULER TO HOLE BOTTOM. A MOEL OF THE RECESSE RILL BIT IS SHOWN ON THE LEFT OF THIS PAGE FOR REFERENCE (RILL FLUTES ARE NOT SHOWN).. THE RECESSE BIT IS ESIGNE TO CREATE A VARIABLE-EPTH COUNTERSUNK RECESS, IN A PLUNGE OPERATION (RILLING).. BITS ARE -FLUTE HELICAL TYPE, GROUN TO INFOCHIP SPECIFICATION FROM SOLI MICRO-GRAIN CARBIE. BITS ARE COATE WITH TITANIUM NITRIE. BITS ARE TO HAVE PERMANENT MARKINGS AS SHOWN IN THE RAWING VIEW ON THIS SHEET INCLUING THE ESIGN ISION AS SHOWN.. BITS ARE TO BE INIVIUALLY PACKAGE AN CUTTING EN SHOUL BE PROTECTE... THIS RAWING INCLUES VIEWS OF A REFERENCE ASSET, RILLE TO AN ARBITRARY RECESS EPTH SHOWN FOR EXAMPLE. THE BIT SHOUL BE ABLE TO ACCOMMO A MAXIMUM RECESS EPTH AS SHOWN ABOVE (MAXIMUM THEORETICAL RECESS). NOTE THAT REAING RANGE IS TYPICALLY REUCE AS THE RECESS EPTH IS INCREASE SO REAING RANGE SHOUL BE TESTE AT THE TARGET RECESS EPTH ALL FEATURES ON THE CUTTING EN OF THE BIT ARE CUTTING FEATURES INCLUING RAII. THERE ARE NO NON-CUTTING FEATURES. INFOCHIP RECOMMENS THAT THE CRITICAL PRIMARY BORE (LOWER) BE MEASURE AFTER RILLING TO ENSURE A PROPER PRESS-FIT. SUGGESTE MAXIMUM ALLOWABLE MEASURE BORES ARE SHOWN IN ETAIL E ON THIS SHEET. THE LOWER BORE IAMETER CAN BE MEASURE USING A HALF-BALL TYPE HOLE GAUGE ALONG WITH A MICROMETER. R0..0 ETAIL E 0 : 9.. COUNTERBORE OCUMENT CONTAINS INFOCHIP INFORMATION AN SHALL NOT BE REPROUCE OR ISCLOSE TO THIR PARTIES WITHOUT PRIOR RAWN CHECKE APPROVE ETAILING "RECESSE" ASSETS (PRESS-FIT) KP ALL IMENSIONS ARE: UNLESS OTHERWISE SPECIFIE. TOLERANCES ON LINEAR IMENSIONS ARE 0.0 UNLESS OTHERWISE SPECIFIE WG. SIZE Install REF - uraplug 9. UHF uraplug 9. UHF of 0

4 A B C E F G H PROCEURE FOR USING SEVERE SERVICE HOLE TREATMENT TOOL FOR URAPLUG 9. UHF (APPLICABLE WITH PRESS-FIT INSTALLS ONLY):. CHECK THAT THE LOWER BORE IS WITHIN SPECIFICATION BEFORE PROCEEING.. REMOVE ANY EBRIS FROM THE RILLE HOLE.. LOCATE THE HOLETOOL-9. OVER THE HOLE AN ENSURE THE TAP IS ENGAGE IN THE HOLE.. HOL THE BASE FIRMLY AGAINST THE ASSET WITH ONE HAN TO PENT THE TOOL FROM TILTING OR MOVING URING USE. GRASP THE FLATS NEAR THE BOTTOM OF THE BASE BETWEEN THUMB AN INEX FINGER.. APPLY ROUGHLY POUNS OF OWNWAR FORCE TO THE KNOB AN TURN THE KNOB CLOCKWISE BY HAN.. CONTINUE PRESSING OWN WHILE TURNING UNTIL THE TAP CONTACTS THE BOTTOM OF THE HOLE. AT THIS POINT, A SHARP RISE IN RIVING TORQUE WILL BE FELT AN TAPPING SHOUL BE STOPPE AT THIS POINT. (ABOUT. TURNS).. KEEP HOLING THE BASE FIRMLY AN ROTATE THE KNOB COUNTERCLOCKWISE TO EXTRACT THE TAP. ONCE THE TAP IS ISENGAGE WITH THE THREAS (ABOUT. TURNS) THE TOOL CAN BE LIFTE AWAY AN HOLE TREATMENT IS COMPLETE. AITIONAL NOTES: THE HOLETOOL-9. IS USE TO CREATE A CONTROLLE UNERCUT IN THE LOWER BORE OF RILLE HOLES FOR URAPLUG 9. UHF. PRESS-FITTING INTO THE TREATE (UNERCUT) HOLES PERMITS MAXIMUM PRESS-OUT FORCE AN MAXIMUM RETENTION OF THE INSTALLE URAPLUG. THE RESULTING CONTROLLE UNERCUT IS A THREA-FORM WITH PARTIAL EPTH AN IT IS VISIBLE TO THE NAKE EYE. AN EXAMPLE PHOTOGRAPH OF SIE-BY-SIE TREATE AN UNTREATE RILLE HOLES IS SHOWN BELOW. THE HOLETOOL-9. CAN BE USE TO TREAT FOR BOTH "FLUSH" AN "RECESSE" HOLES. THE HOLETOOL-9. IS ESIGNE TO BE USE BY HAN WHERE HOLES ARE RILLE INTO ASSETS ON FLAT SURFACES. THE TOOL BASE CAN BE MOIFIE BY MACHINING OR REESIGN SO THAT IT WILL WORK WITH OTHER ASSET SURFACES (SUCH AS CYLINRICAL SURFACES). KNOB PHOTOGRAPHIC EXAMPLE OF TREATE AN UNTREATE HOLES BASE TAP HOLETOOL-9. ETAILING USE OF HOLETOOL-9. OCUMENT CONTAINS INFOCHIP INFORMATION AN SHALL NOT BE REPROUCE OR ISCLOSE TO THIR PARTIES WITHOUT PRIOR RAWN KP. ALL IMENSIONS ARE: UNLESS OTHERWISE SPECIFIE. TOLERANCES ON LINEAR IMENSIONS ARE 0.0 UNLESS OTHERWISE SPECIFIE WG. SIZE 0 Install REF - uraplug 9. UHF uraplug 9. UHF CHECKE APPROVE NONE SEE ABOVE of

5 A B C E F G H SPOT-FACE FEATURE F F STEP - COMPLETE INSTALLATION STEP SECTION F-F : INSTALLE EXAMPLE URAPLUG 9. RIVER TOOL K STEP : ETAIL K : SPOT-FACE URAPLUG SHOUL BE FLUSH TO SLIGHTLY EPRESSE RELATIVE TO SPOT-FACE FEATURE AFTER INSTALL STEP INSTALLATION STEPS (NEAR-FLUSH, PRESS-FIT TYPE): STEP : ENSURE ASSET IS RILLE AN THAT THE HOLE IS TREATE WITH SEVERE SERVICE HOLE TOOL, AS APPLICABLE, TO SPECIFICATIONS AN ENSURE THE INSTALL HOLE IS CLEANE OF ANY CUTTING FLUI AN EBRIS STEP : IF REQUIRE, COAT THE SIEWALLS AN BOTTOM OF THE RILLE HOLE WITH A "WET" CORROSION INHIBITOR PROUCT. (STEP IS NOT SHOWN) CORROSION INHIBITOR PROUCTS ARE NOT SPECIFIE ON THIS RAWING. STEP : IF USING A CORROSION INHIBITOR PROUCT, ENSURE THAT IT IS STILL WET BEFORE PROCEEING. PLACE THE URAPLUG WITH LOGO SIE UP ONTO THE ASSET NEAR THE HOLE. FOR MAXIMUM REAING RANGE, ORIENT THE URAPLUG AS SPECIFIE ON SHEET. USE FINGER ON THE TAG TO SLIE IT INTO POSITION. WHEN NESTE N POSITION, THE TAG WILL ROP OWN SLIGHTLY. AT THIS POINT IT IS NESTE, REAY TO BE PRESS-FITTE. STEP : USE A PRESS SUCH AS AN ARBOR PRESS OR RILL-PRESS AN CHUCK THE RIVER TOOL IN THE PRESS (STEP NOT SHOWN) STEP : VISUALLY ALIGN THE ASSET AN NESTE URAPLUG WITH THE RIVER TOOL STEP : USE THE PRESS TO INSTALL THE URAPLUG UNTIL IT IS FULLY BOTTOME OUT. IT SHOUL BE FLUSH WITH THE RILLE SPOT-FACE FEATURE, OR SLIGHTLY RECESSE TO THE SPOT-FACE FEATURE. TRY TO USE ONLY ENOUGH FORCE NEEE TO SEAT THE URAPLUG FULLY. (STEP NOT SHOWN) STEP : CLEAN ANY EXCESS CORROSION INHIBITOR PROUCT (IF APPLICABLE) AN VISUALLY INSPECT THE INSTALLATION FOR FULL INSERTION AN CARRY OUT REAING TEST. AITIONAL NOTES: AN EXAMPLE OF A RIVER TOOL IS SHOWN WITH SUGGESTE IMENSIONS. ENSURE THAT THE RIVING FACE OF THE TOOL IS FLAT, SMOOTH AN SQUARE. THE TOOL CAN BE TURNE ON A LATHE FROM /" OR /" HEXAGONAL OR ROUN BAR STOCK. ACETAL (ELRIN, ACETRON, ETC) IS RECOMMENE FOR THE. IF THE INSTALLATION WILL NOT BE USING A TREATE HOLE, THE URAPLUG MAY BE INSTALLE MANUALLY IF A PRESS IS NOT PRACTICAL. IN THIS CASE, IT IS RECOMMENE TO USE THE RIVER TOOL, AN ALIGN IT BY EYE TO THE NESTE URAPLUG KEEPING IT PARALLEL TO THE RILLE HOLE. COMPLETE THE INSTALLATION BY TAPPING THE TOOL WITH A LB TO. LB EA-BLOW HAMMER TO FULLY SEAT THE URAPLUG. FOR TREATE HOLES, INFOCHIP STRONGLY RECOMMENS TO USE A PRESS FOR THE INSTALLATION. EXTRACTION: AN INSTALLE URAPLUG 9. UHF CAN BE REMOVE WITHOUT AMAGING THE INSTALLATION HOLE. THE FOLLOWING PROCEURE CAN BE USE WITH FLUSH AN RECESSE INSTALLATIONS USING TREATE AN UNTREATE HOLES:. RILL THROUGH THE CENTER OF THE PLASTIC LOGO SURFACE OF THE TAG USING A /" IAMETER FLAT BOTTOM HIGH-SPEE STEEL STANAR EN MILL. VISUALLY CENTER THE CUTTER AN CUT ONLY 0.0 EEP TO AVOI AMAGE TO THE CUTTER. USING A STEEL PUNCH AN HAMMER, CAREFULLY BREAK UP THE CERAMIC CORE. INTERMITTENTLY CLEAR ANY LOOSE PARTICLES USING A VACUUM OR COMPRESSE AIR. ENSURE TO WEAR PROTECTIVE EYEWEAR AN CLOTHING.. ONCE THE CERAMIC CORE IS REMOVE, TAP A T- (TORX) SCREWRIVER OR BIT INTO THE REMAINING PLASTIC HOUSING CAVITY.. FOR A TREATE HOLE, SIMPLY TWIST THE TOOL COUNTER-CLOCKWISE AN THE PLUG WILL SCREW OUT.. FOR AN UNTREATE HOLE, TWIST AN LIFT/TILT SLIGHTLY AN THE PLUG WILL MOVE OUT OF THE HOLE. OCUMENT CONTAINS INFOCHIP INFORMATION AN SHALL NOT BE REPROUCE OR ISCLOSE TO THIR PARTIES WITHOUT PRIOR RAWN CHECKE APPROVE URAPLUG SHOUL BE FULLY INSERTE TO BOTTOM OF HOLE FOR PROPER REAING FUNCTION. ALL IMENSIONS ARE: UNLESS OTHERWISE SPECIFIE ETAIL INSTALLE : ETAILING "NEAR-FLUSH" INSTALLATION PROCEURE PRESS-FIT TYPE KP TOLERANCES ON LINEAR IMENSIONS ARE 0.0 UNLESS OTHERWISE SPECIFIE WG. SIZE Install REF - uraplug 9. UHF uraplug 9. UHF of 0

6 A B C E F G H 0..0 SHOULER RECESS M AHESIVE P9. SHOWN IN BLACK COLOR IN THIS VIEW AHESIVE P9. EXAMPLE ASSET VENT NOTCH EXAMPLE OF COMPLETE INSTALLATION EXAMPLE ASSET SECTION M-M 0 : M INSTALLATION STEPS (NEAR-FLUSH, AHESIVE TYPE): THIS RAWING PROVIES AN EXAMPLE OF P9. UHF AHESIVE-TYPE INSTALLATION PROCEURE WHERE A BASIC SELF-LEVELING AHESIVE IS USE. THIS RAWING IS NOT MEANT TO PROVIE RECOMMENATIONS FOR AHESIVE TYPES, MIXING, OR CURING. FOR CLARITY, AHESIVE IS SHOWN AS TRANSPARENT ON SHAE VIEWS. EXAMPLE ASSET IS SHOWN IN ARK GREY COLOR. GREEN COLOR SURFACES ARE ASSET SURFACES FORME URING THE RILLING OPERATION. THE P9. HOUSING IS SHOWN IN LIGHT GREY. STEP : ENSURE ASSET IS RILLE USING INFOCHIP RILL BIT: BIT-9.-HAN-RILL TO INFOCHIP SPECIFICATION: ASSET-REF-P9.-AHESIVE. IF INTENING TO COVER THE TAG WITH AHESIVE, ENSURE TO USE A "SHOULER RECESS" HEIGHT APPROXIMATELY AS SHOWN ON ASSET-REF-P9.-AHESIVE. STEP : IF REQUIRE, CLEAN THE INSTALLATION HOLE AREA SO THAT IS IS FREE OF ANY EBRIS OR CUTTING FLUIS. STEP : ISPENSE AHESIVE TO THE FLOOR OF THE RILLE HOLE UNTIL IT IS ROUGHLY 0% TO % FILLE. MINIMIZE BUBBLES WHILE ISPENSING. STEP : ENSURE VENT-NOTCH IS ALIGNE TO ASSET WITH PREFERRE ORIENTATION FROM SHEET AN PLACE P9. INTO THE WET AHEISVE. ENSURE LOGO SIE FACES UP AN USE A SOFT TOOL TO PRESS THE P9. OWN FULLY TO THE BOTTOM OF THE HOLE. IF USING SELF-LEVELING AHESIVE, IT SHOUL FLOW ABOVE AN COVER THE P9. TAG. IF NEEE, USE A TOOL TO ENSURE THE AHESIVE COMPLETELY COVERS THE TAG'S LOGO SURFACE. IF NECESSARY, A AHESIVE AN BREAK LARGE BUBBLES IF NEEE. STEP : IF NEEE, USE A FLAT THIN TOOL SUCH AS A RAZOR-BLAE AS A SCRAPER TOOL TO REMOVE EXCESS AHESIVE AN CREATE A FLAT AHESIVE SURFACE, FLUSH WITH ASSET TOP SURFACE. IF NEEE, WIPE AWAY ANY EXCESSS AHESIVE AFTER SCRAPING FLAT. STEP : ALLOW AHESIVE TO CURE TO AHESIVE MANUFACTURER'S SPECIFICATIONS. STEP : CARRY OUT BASIC VISUAL INSPECTION AN FUNCTIONAL REAING TEST. ETAILING INSTALLATION PROCEURE AHESIVE TYPE OCUMENT CONTAINS INFOCHIP INFORMATION AN SHALL NOT BE REPROUCE OR ISCLOSE TO THIR PARTIES WITHOUT PRIOR RAWN CHECKE APPROVE. ALL IMENSIONS ARE: UNLESS OTHERWISE SPECIFIE. TOLERANCES ON LINEAR IMENSIONS ARE 0.0 UNLESS OTHERWISE SPECIFIE WG. SIZE Install REF - uraplug 9. Adhesive of