Technical Particular Of Furniture Part-I

Transcription

1 Annexure-B 1/81 Technical Particular Of Furniture Part-I Recommended by Technical Specification Committee Dated

2 Annexure-B CSIDC/MKD/TECH/ /27 THECHNICAL SPECIFICATION OF FURNITURE PART-I (TSC ) 2/81 Sl No Specification No. INDEX Item Description Item Code Item Size Schedule -1 OFFICE & SCHOOL FURNITURE:- 1 SF19E0001 Executive Table (3 Equal Drawer & Cupboard) 1800 x 1200 x 750 mm 2 SF19E0002 Executive Table (3 Equal Drawer & Cupboard) 1800 x 900 x 750 mm 3 SF19E0003 Executive Table (3 Equal Drawer & Cupboard) 1500 x 900 x 750 mm 4 SF19E0004 Office Table (Drawer & cupboard unit) 1200 x 750 x 750 mm 5 SF19E0005 Office Table (3 Drawer) 1200 x 600 x 750 mm 6 SF19E0006 Office Table (2 Drawer) 1000 x 600 x 750 mm 7 SF19E0007 Student Table 600 x 450 x SF19E0008 Student Chair 900 x 400 / 375 x SF19E0009A All Steel Student Desk (Without Shelf) 900 x 425 x 750 mm 10 SF19E0009B All Steel Student Desk (With Shelf) 900 x 425 x 750 mm 11 SF19E0010 All Steel Student Bench 900 x 300 x 450 mm 12 SF19E0011 All Steel Dual Desk (Three Seater) 1500 x 900 x 750 / 450 mm 13 SF19E0012 All Steel Dual Desk (Three Seater Junior) 1150 x 900 x 750 / 475 mm 14 SF19E0013 Dual Desk (2 seater junior) 900 x 850 x 900 / 450 / 750 mm 15 SF19E0014 Dual Desk (2 seater Senior) 1050 x 900 x 900 / 450 / 750 mm 16 SF19E0015A STUDENT Desk, Angle iron frame (Without shelf) 900 x 425 x 750 mm 17 SF19E0015B STUDENT Desk, Angle iron frame (With shelf) 900 x 425 x 750 mm 18 SF19E0016 STUDENT BENCH (Angle iron frame) 900 x 300 x 450 mm 19 SF19E0017 Executive Chair (Continuous Arm) 1000/ 450 x 550 x 550 mm 20 SF19E0018 Office Chair (Fixed Back) 950/ 450 x 550 x 550 mm 21 SF19E0019 Office Chair (Flexible Back) 950/ 450 x 550 x 550 mm 22 SF19E0020 Visitor Chair (With Arm) 800/ 450 x 525 x 550 mm 23 SF19E0021 Visitor Chair (Without Arm) 800/ 450 x 525 x 550 mm 24 SF19E0022 Office Revolving Chair (High Back) 600 x 600 x 1050 /1150 mm 25 SF19E0023 Executive Revolving Chair (High Back) 650 x 650 x 1100 /1200 mm 26 SF19E0024A Steel Stool MDF Top 450 x 305 x 305 mm 27 SF19E0024B Steel Stool MDF Top 600 x 305 x 305 mm 28 SF19E0024C Steel Stool MDF Top 690 x 410 x 410 mm 29 SF19E0025 Steel Stool Cushioned Top 400 x 400 x 550 / 650 mm 30 SF19E0026 Steel Bench with Back rest 1500 x 450 x 450 / 900 mm Schedule -2 Cabinet & Book case :- 31 SF19E0027 Cabinet Plain (Full) of 0.8 mm CR Sheet 1980 x 915 x 480 mm 32 SF19E0028 Cabinet Plain (Medium) of 0.8 mm CR Sheet 1675 x 840 x 480 mm 33 SF19E0029 Cabinet Plain (Small) of 0.8 mm CR Sheet 1270 x 760 x 430 mm 34 SF19E0030 Cabinet Plain (Mini) of 0.8 mm CR Sheet 915 x 610 x 380 mm 35 SF19E0031 Cabinet with One Locker of 0.8 mm CR Sheet 1980 x 915 x 480 mm 36 SF19E0032 Cabinet with One Plain Locker of 0.8 mm CR Sheet 1675 x 840 x 480 mm 37 SF19E0033 Cabinet Wardrobe of 0.8 mm CR Sheet 1980 x 900 x 560 mm

3 38 SF19E0034 Cabinet Wardrobe (Mirror) of 0.8 mm CR Sheet 1980 x 900 x 560 mm 39 SF19E0035 Steel Book Case 0.8 mm CR Sheet 1675 x 840 x 380 mm Schedule -3 Lockers, Cabinets & Safe :- 40 SF19E0036 Industrial Locker Cabinet (9 Lockers) 0.8 mm CR Sheet 1800 x 900 x 400 mm 41 SF19E0037 Industrial Locker Cabinet (16 Locker) 0.8 mm CR Sheet 1800 x 1200 x 400 mm 42 SF19E0038 Glass Door Cabinet of 1 mm CR Sheet 0.8 mm CR Sheet 1980 x 900 x 480 mm 43 SF19E0039 Cash Box of 1 mm CR Sheet 1 mm CR Sheet 250 x 380 x 300 mm Schedule -4 Tin Box & Anaj Kothi:- 44 SF19E0040 Kit Box of 0.55 mm GP Sheet 680 x 380 x 300 mm 45 SF19E0041 Tin Box of 0.55 mm GP Sheet 750 x 450 x 450 mm 46 SF19E0042 Tin Box of 0.55 mm GP Sheet 750 x 600 x 450 mm 47 SF19E0043 Tin Box of 0.55 mm GP Sheet 900 x 450 x 350 mm 48 SF19E0044 Tin Box of 0.55 mm GP Sheet 900 x 600 x 450 mm 49 SF19E0045 Tin Box of 0.75 mm GP Sheet 1000 x 750 x 450 mm 50 SF19E0046 Tin Box of 0.75 mm GP Sheet 1200 x 750 x 650 mm 51 SF19E0047 Square Anaj Kothi of 0.75 mm GP Sheet 900 x 450 x 450 mm 52 SF19E0048 Square Anaj Kothi of 0.75 mm GP Sheet 750 x 380 x 380 mm Schedule -5 Racks & Cots :- 53 SF19E0049 Angle Iron Rack 900 x 900 x 380 mm 54 SF19E0050 Angle Iron Rack 900 x 900 x 450 mm 55 SF19E0051 Angle Iron Rack 1800 x 900 x 380 mm 56 SF19E0052 Angle Iron Rack 1800 x 900 x 450 mm 57 SF19E0053 Angle Iron Rack 1950 x 900 x 450 mm 58 SF19E0054 Angle Iron Rack 2100 x 900 x 450 mm 59 SF19E A Angle Iron Cot (Takhat with 25 mm Ply) 1950 x 900 x 450mm 60 SF19E B Angle Iron Cot (Takhat with 18 mm Ply) 1950 x 900 x 450mm 61 SF19E0056 Angle Iron Cot (Strip Flat) 1950 / 1870 x 900 x 450 mm 62 SF19E0057 Angle Iron Cot (18mm Plywood) 1950 / 1870 x 900 x 450 mm 63 SF19E0058 Cushion Cot Three Fold (6 Leg) 1900 / 1800 x 900 x 450 mm 64 SF19E0059 Double sleeper hostel Bed 1950/ 1870 x 900 x 450 / 1350mm Schedule -6 Computer Furniture 65 SF19E0060A COMPUTER CHAIR (MID BACK) (With Handle) 600 x 600 x 850 /950 mm 66 SF19E0060B COMPUTER CHAIR (MID BACK) (Without Handle) 600 x 600 x 850 /950 mm 67 SF19E0061A COMPUTER CHAIR (LOW BACK) (With Handle) 600 x 600 x 750 /850 mm 68 SF19E0061B COMPUTER CHAIR (LOW BACK) (Without Handle) 600 x 600 x 750 /850 mm 69 SF19E0062 COMPUTER PRINTER TABLE 900 x 600 x 750 mm 70 SF19E0063 COMPUTER CUM PRINTER TABLE 1200 x 600 x 750 mm 71 SF19E0064 COMPUTER TABLE (COMPACT) 650 x 500 x 750 mm 72 SF19E0065 PRINTER TABLE 700 x 500 x 750 mm 73 SF19E0066 PRINTER TABLE (WITH DRAWER) 800 x 500 x 750 mm 74 SF19E0067 COMPUTER TABLE (1 DRAWER & CUPBOARD) 1050 x 600 x 750 mm 75 SF19E0068 COMPUTER TABLE (3 DRAWER) 1200 x 600 x 750 mm 76 SF19E0069 COMPUTER TABLE (2 DRAWER & CUPBOARD) 1300 x 700 x 750 mm 3/81 General Requirements 1. The drawings, figures & sketches given in this catalogue are not to scale. 2. Dimensions shall be read in metric unit only & corrected dimensions from details below. 3. tolerances in dimensions are permissible as follows, if not specified : a. In overall size + 10mm. b. In thickness of pipe & sheets etc. as per relevant Indian Standard

4 4/81 4. Welding of pipe structures and MS sheets shall be done by gas welding only and on heavier sections (Above 2.5mm) by arc welding. 5. Painting on steel sections: a. Surface finishing shall be done before painting by weld chipping / grinding / filing / emery paper process. b. Two coat of metal primer of standard make like ASIAN/BERGER/SHALIMAR/ NEROLAC shall be applied after proper putty applied on the surface and over it one under coat and the final coat of superior quality synthetic enamel paint of standard makes like ASIAN/BERGER/SHALIMAR/NEROLAC should be applied in T A Grey /Light Grey/ SC Grey Sheds and olive green. c. The whole consignment of a supply order shall be painted in one shed only. 6. The color / shed of board lamination shall be approved by Consignee, if desired. 7. Wherever required Pre-laminated Medium Density Fiber Board of 18mm/25mm thick (ISI mark) 8. If the consignee demands any special quality of laminate, etc. other than those specified the same can be provided only after prior approval. And coasting of technical department of the Nigam provided the cost does not materially change. 9. Minor deviations from specifications. In order to improve strength / finish & comfort of the product or due to non-availability of particular material can be allowed at the discretion of CSIDC. 10. Wherever specified/required, good quality chrome plating on the steel section/components shall be provided. Two years replacement guarantee for chrome plated components/parts is to be given by the supplier. Wherever necessary welding riveting pressing. Folding shall be done properly. 11. Finishing & workmanship in the product is of prime importance and must be of good quality. 12. The supplier shall ensure that the product is manufactured as per specification and all the fitting/accessories used are of standard quality, wherever not specified. All the Table Drawer are to be provide with reputed make sliding channel arrangement. Good quality Bakelite handle as shown in Drawing. 13. Teak wood used in the furniture shall be seasoned wood with major defects, like dead knots with through hole, wide cracks etc. shall not be used. Clear Poly Urethane lacquer polish shall be done on all wooden items. 14. Wherever necessary good quality plastic / P.U milky white shoe`s are to be used. 15. Warrantee: One year from date of delivery to consignee.

5 5/81 If supply of sub-standard product with/without manufacturing defect is observed even after supply. The supplier shall repair/replace the defective product free of cost, during warrantee period within one week period. 16. (A) if any dimensional discrepancy with respect to drawing and specifications due to calculation/printing mistake/any error is observed, the same may please be brought to the notice of CSIDC before opening of tender. (B) If any dimensional discrepancy is observed during manufacturing, the same may be communicated to the In-charge Marketing immediately in writing. (C) Wherever not mentioned. Standard manufacturing practice is to be adopted.

6 Schedule -1 6/81 OFFICE FURNITURE & SCHOOL FURNITURE

7 7/81 EXECUTIVE TABLE (With Drawer three equal) SPN NO.:- SF19E0001 OVEERALL SIZE : (L)1800 X (W) 1200 (H) 750 mm. MATERIAL DETAILS :- 1. Table Top :- 25mm thick ISI Marked Prelaminated MDF board IS with upto date amendment 2. Leapping :- Teak wood half round 50mm wide, supported from inside by Jungle wood 25 x 25 mm. OR PVC leaping 25mm with proper edge banding machine. 3. Frame Structure :- ERW Square pipe 32x32x1.25mm in size1600(l)x 900(W)x725(H)mm. with Center Support as indicated by 9, To be welded in center below the top as shown in figure item Spn No.SF19E Pannel (On Fame) :- 18mm thick Pre-laminated MDF board covering frame structure from 3 Sides (Height-600mm) with proper edge leaping and fixed on 4 flats of 18 x 3 mm with nut bolts (Not to be fixed directly with main leg pipe). 5. Drawer & Cupboard:- CR sheet 0.80mm thk Confirming to IS Cupboard Size :- size 600(D) x400(w) x450mm(h). 7. Drawer Size :- 500(L)X100mm(D) Minimum. Drawer 3Nop. And one folding shelf in cup Board. 8. Drawer Sliding :- Nylon tear resistant wheels rolling in C channels between drawer & box. 9. Cupboard Shutter :- BOX TYPE made of 0.80mm CRCA Sheet Confirming to IS Footrest :- ERW square pipe 32x32x1.25mm in full length and with 100mm gap between two pipes 11. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 12. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

8 8/81 EXECUTIVE TABLE (With Drawer three equal) SPN NO.. :- SF19E0002 OVEERALL SIZE : (L)1800 X (W) 900 (H) 750 mm. MATERIAL DETAILS :- 1. Table Top :- 25mm thick ISI Marked Prelaminated MDF board IS with upto date amendment 2. Leapping :- Teak wood half round 50mm wide, supported from inside by Jungle wood 25 x 25 mm. OR PVC leaping 25mm with proper edge banding machine. 3. Frame Structure :- ERW Square pipe 32x32x1.25mm in size1600(l)x 750(W)x725(H)mm. with Center Support as indicated by 9, To be welded in center below the top as shown in figure. 13. Pannel (On Fame) :- 18mm thick Pre-laminated MDF board covering frame structure from 3 Sides (Height-600mm) with proper edge leaping and fixed on 4 flats of 18 x 3 mm with nut bolts (Not to be fixed directly with main leg pipe). 4. Drawer & Cupboard:- CR sheet 0.80mm thk Confirming to IS Cupboard Size :- size 600(D) x400(w) x450mm(h). 6. Drawer Size :- 500(L)X100mm(D) Minimum. Drawer 3Nop. And one folding shelf in cup Board. 7. Drawer Sliding :- Nylon tear resistant wheels rolling in C channels between drawer & box. 8. Cupboard Shutter :- BOX TYPE made of 0.80mm CRCA Sheet Confirming to IS Footrest :- ERW square pipe 32x32x1.25mm in full length and with 100mm gap between two pipes 10. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 11. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

9 9/81 EXECUTIVE TABLE (With Drawer three equal) SPN NO.. :- SF19E0003 OVEERALL SIZE : (L)1500 X (W) 900 (H) 750 mm. MATERIAL DETAILS :- 1. Table Top :- 25mm thick ISI Marked Prelaminated MDF board IS With upto date amendment 2. Leapping :- Teak wood half round 50mm wide, supported from inside by Jungle wood 25 x 25 mm. OR PVC leaping 25mm with proper edge banding machine. 3. Frame Structure :- ERW Square pipe 32x32x1.25mm in size1350(l)x750(w)x725(h) mm. with Center Support as indicated, To be welded in center below the top as shown in figure. 14. Pannel (On Fame) :- 18mm thick Pre-laminated MDF board covering frame structure from 3Sides (Height-600mm) with proper edge leaping and fixed on 4 flats of 18 x 3 mm with nut bolts (Not to be fixed directly with main leg pipe). 4. Drawer & Cupboard:- CR sheet 0.80mm thick Confirming to IS Cupboard Size :- size 600(D) x400(w) x450mm(h). 6. Drawer Size :- 500(L)X100mm(D) Minimum. Drawer 3Nop. And one folding shelf in cup Board. 7. Drawer Sliding :- Nylon tear resistant wheels rolling in C channels between drawer & box. 8. Cupboard Shutter :- BOX TYPE made of 0.80mm CRCA Sheet Confirming to IS Footrest :- ERW square pipe 32x32x1.25mm in full length and with 100mm gap between two pipes 10. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 11. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

10 10/81 OFFICE TABLE SPN NO.. :- SF19E0004 OVEERALL SIZE: (L) 1200 X (W) 750 (H) 750 mm. MATERIAL DETAILS :- 1. Table Top :- 25mm THK. ISI Marked Pre Laminated MDF Board IS with upto date amendment 2. Edge Leaping :- Teak wood half round 25mm wide, OR PVC leaping 25mm with proper edge banding machine 3. Frame Structure :- ERW Square pipe 32 x 32 x 1.25 mm in size1100(l) x 600(W) x 725(H) mm. 4. Drawer & Cupboard:- CR sheet 0.80mm thick Confirming to IS-513 Size = 600(D) x 350(W) x 450mm(H). 5. Drawer Size :- 500(L)X100mm(D) Minimum. 6. Cupboard shutter :- BOX TYPE made of 0.80mm CR sheet Confirming to IS Foot Rest :-ERW square pipe 32 x 32 x 1.25mm in full length and gap between two pipes approx. 100.mm. 8. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 9. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

11 11/81 OFFICE- TABEL SPN NO.: - SF19E0005 OVERALL SIZE : (L)1200 X (W} 600 (H) 750 mm MATERIAL DETAILS:- 1. Table Top :- 25mm THK. ISI Marked Pre Laminated MDF Board IS with upto date amendment 2. Edge Leaping :- Teak wood half round 25mm wide, OR PVC leaping 25mm with proper edge banding machine 3. Frame Structure :- ERW Square pipe 32 x 32 x 1.25 mm in size1100(l) x 500(W) x 725(H) mm. 4. Drawer & Cupboard:- CR sheet 0.80mm thick Confirming to IS-513 Size = 500(D) x 350(W) x 450mm(H). 5. Drawer Size :- 450(L) x 100mm(D) Minimum. 6. Foot Rest :-ERW square pipe 32 x 32 x 1.25mm in full length. 7. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 8. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

12 12/81 OFFICE TABLE SPN NO.. :- SF19E0006 OVEERALL SIZE : (L)1000 X (W) 600 (H) 750 mm. MATERIAL DETAILS :- 1. Table Top :- 25mm THK. ISI Marked Pre Laminated MDF Board IS with upto date amendment 2. Edge Leaping :- Teak wood half round 25mm wide, OR PVC leaping 25mm with proper edge banding machine 3. Frame Structure :- ERW Square pipe 32 x 32 x 1.25 mm in size 900(L) x 450(W) x 725(H) mm. 4. Drawer & Cupboard:- CR sheet 0.80mm thick Confirming to IS-513 Size = 450(D) x 350(W) x 250mm(H). 5. Drawer Size :- 400(L) x 100mm(D) Minimum. 6. Foot Rest :-ERW square pipe 32 x 32 x 1.25mm in full length. 7. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 8. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

13 13/81 STUDENT TABLE CODE No. : SF19E0007 (Overall Size : 600x450x750mm ) Steel Structure M.S. Angle Iron frame with MDF Board mm x 32 x 2.5 mm MATERIAL DETAILS :- 1. Table Top :- 18mm THK. ISI Marked Pre Laminated MDF Board IS with upto date amendment.(in approved shed) Size : 600 x 450 mm 2. Edge Leaping :- Teak wood half round 18mm wide polish, OR PVC leaping 18mm With proper edge banding machine 3. Frame Structure :- Mild steel Angle 32 x 32 x 2.5 mm in size 550 (L) x 400(W) x 732(H) mm. 4. Foot Rest :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 5. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 6. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

14 14/81 STUDENT CHAIR CODE No. : SF19E0008 (Steel Structure M.S. Angle Iron frame with MDF Board) 900 x 400 / 375 x x 32 x 2.5 mm MATERIAL DETAILS :- 1. Chair Seat :- 18mm THK. ISI Marked Pre Laminated MDF Board IS with upto date amendment.(in approved shed) Size: 400 x 400mm 2. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping 18mm with proper edge banding machine. 3. Frame Structure :- Mild steel Angle 32 x 32 x 2.5 mm in size 375 (L) x 375 (W) x 462 (H)mm. and total height with back rest 900 mm. with all Supports as shown in figure. 4. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 5. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

15 15/81 ALL STEEL STUDENT DESK Spn No.. :- SF19E0009 OVERALL SIZE : 900 x 425 x 750mm Sheet to be folded 3times, 1 st bend over the angle 32 mm, 2 nd bend 15 mm inside over the Angle edge, 3 rd bend 10mm to avoid sharp edge of sheet. MATERIAL DETAILS :- SF19E0009 (A) SF19E0009 (B) Without Shelf With Shelf 1. Desk table Top :- Made from 1.00 mm CR sheet Confirming to IS-513 with all edges shall be formed covering the angles with edges folded over the structures first 32mm length at 90 Degree & 2 times complete fold of 10 mm & 5mm. 2. Frame Structure :- Mild steel Angle 32 x 32 x 2.5 mm in size 900 (L) x 425 (W) x 750(H) mm. 3. Shelf Size :- Made from 0.80 mm CR sheet formed covering frame of M.S Angle 32 x 32 x 2.5 mm in size 900 (L) x 425 (W), 175mm below the top. 4. Foot Rest & support :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 5. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 6. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

16 16/81 ALL STEEL BENCH FOR STUDENTS Spn No.. :- SF19E0010 OVERALL SIZE : 900 x 300 x 450mm Sheet to be folded 3times, 1 st bend over the angle 32 mm, 2 nd bend 15 mm inside over the Angle edge, 3 rd bend 10mm to avoid sharp edge of sheet. MATERIAL DETAILS :- 1. Bench Top :- Made from 1.00 mm CR sheet Confirming to IS-513 with all edges shall be formed covering the angles with edges folded over the structures first 32mm length at 90 Degree & 2 times complete fold of 10 mm & 5mm. 2. Frame Structure :- Mild steel Angle 32 x 32 x 2.5 mm in size 900 (L) x 300 (W) x 450 (H) mm, with two equal distance width wise angle support. 3. Foot Rest support :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 4. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 5. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc

17 17/81 ALL STEEL DUAL DESK( Three Seater) Spn No. : - SF19E0011 OVERALL SIZE : (L)1500 x (W) 900 X (H) 750/450mm. MATERIAL DETAILS :- 7. Desk & Bench Top :- Made from 1.00 mm CR sheet Confirming to IS-513 with all edges shall be formed covering the angles with edges folded over the structures first 32mm length at 90 Degree & 2 times complete fold of 10 mm & 5mm. Overall Frame Size : 1500 x 900 x 750 Desk height x 475 Bench height. 8. Desk Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1500 (L) x 375 (W) x 750 (H) mm, with two equal distance width wise angle support. 9. Bench Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1500 (L) x 300 (W) x 450 (H) mm, with two equal distance width wise angle support. 10. Shelf Size :- Made from 1.00 mm CR sheet formed covering frame of M.S Angle 32 x 32 x 2.5 mm in size 1500 (L) x 375 (W), 175mm below the top. 11. Foot Rest support :- M.S Angle 32 x 32 x 2.5 mm in full length, 150mm above ground. 12. Special Requirement : - Machine made corner plates corner plates should be folded towards inside to avoid the sharp edge, No sharp edge on any part of dual desk shall be allowed. 13. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc

18 18/81 ALL STEEL DUAL DESK( Three Seater Junior) Spn No. : - SF19E0012 OVERALL SIZE: (L)1150 x (W) 900 X (H) 750/475mm. (Without back rest & without shelf) MATERIAL DETAILS :- 1. Desk & Bench Top :- Made from 1.00 mm CR sheet Confirming to IS-513 with all edges shall be formed covering the angles with edges folded over the structures first 32mm length at 90 Degree & 2 times complete fold of 10 mm & 5mm. Overall Frame Size : 1150 x 900 x 750 Desk height x 475 Bench height 2. Desk Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1150 (L) x 375 (W) x 750 (H) mm, with two equal distance width wise angle support. 3. Bench Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1150 (L) x 300 (W) x 450 (H) mm, with two equal distance width wise angle support. 4. Shelf Size :- Made from 1.00 mm CR sheet formed covering frame of M.S Angle 32 x 32 x 2.5 mm in size 1150 (L) x 375 (W), 175mm below the top. 5. Foot Rest support :- M.S Angle 32 x 32 x 2.5 mm in full length, 150mm above ground. 6. Special Requirement :- Machine made corner plates corner plates should be folded towards inside to avoid the sharp edge, No sharp edge on any part of dual desk shall be allowed. 7. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc

19 19/81 DUAL DESK (Two seater Junior) Spn No. : SF19E0013 (With Angle iron frame) 900x850x/900/450/750mm Back Support MATERIAL DETAILS :- 1. Desk & Bench Top :- 18mm thk ISI Marked Pre Laminated MDF Board confirming to IS 14587:1998, Overall Frame Size : 900 x 850 x 750 Desk height x 450 Bench height & 900mm Backrest height. 2. Desk Top :- made of 18mm thk MDF Board size: 900 x 450mm. 3. Bench Top :- made of 18mm thk MDF Board size: 900 x 325mm. 4. Back rest ;- made of 18mm thk MDF Board size: 900 x 150mm 5. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping 18mm with proper edge banding machine 6. Desk Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 850 (L) x 425 (W) x 732 (H) mm, with two equal distance width wise angle support. 7. Bench Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 850 (L) x 300 (W) x 432 (H) mm, with two equal distance width wise angle support. 8. Shelf Size :- Made from 18mm thk MDF Board in frame of M.S Angle 32 x 32 x 2.5 mm in size 850 (L) x 425 (W), 175mm below the top. 9. Special Requirement :- No sharp edge on any part of dual desk shall be allowed. 10. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc

20 20/81 DUAL DESK (Two Seater Senior) Spn No. : SF19E0014 (With angle iron frame) 1050x900x900/450/750mm MATERIAL DETAILS :- 1. Desk & Bench Top :- 18mm thk ISI Marked Pre Laminated MDF Board confirming to IS 14587:1998, Overall Frame Size : 1000 x 900 x 750 Desk height x 450 Bench height & 900mm Backrest height. 2. Desk Top :- made of 18mm thk MDF Board size: 1050 x 450mm. 3. Bench Top :- made of 18mm thk MDF Board size: 1050 x 325mm. 4. Back rest ;- made of 18mm thk MDF Board size: 1050 x 150mm 5. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping 18mm with proper edge banding machine 6. Desk Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1000 (L) x 425 (W) x 732 (H) mm, with two equal distance width wise angle support. 7. Bench Frame & size :- made of M.S Angle 32 x 32 x 2.5 mm in size 1000 (L) x 300 (W) x 432 (H) mm, with two equal distance width wise angle support. 8. Shelf Size :- Made from 18mm thk MDF Board in frame of M.S Angle 32 x 32 x 2.5 mm in size 1000 (L) x 425 (W), 175mm below the top. 9. Special Requirement :- No sharp edge on any part of dual desk shall be allowed. 10. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc

21 21/81 STUDENT DESK (Angle iron frame) Spn No.. : SF19E0015 (overall size - 900x425x750 mm MDF Top) 32 x 32 x 2.5 mm MATERIAL DETAILS :- SF19E0015 (A) SF19E0015 (B) Without Shelf With Shelf 1. Desk table Top :- Made from 18mm thk ISI Marked Pre Laminated MDF Board confirming to IS 14587:1998 with TOP size: 900 x 425 mm. 2. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping 18mm with proper edge banding machine. 3. Frame Structure :- As shown in figure made of Mild steel Angle 32 x 32 x 2.5 mm in size 850 (L) x 375 (W) x 732(H) mm. with support & footrest. 4. Shelf Size :- Made from 18mm thk ISI Marked Pre Laminated MDF Board in M.S Angle 32 x 32 x 2.5 mm in size 850 (L) x 375 (W), 175mm below the top. 5. Foot Rest & support :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 6. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 7. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

22 22/81 STUDENT BENCH (Angle iron frame) Spn No.: SF19E0016 (Overall Size : 900x300x450mm MDF Top) MATERIAL DETAILS :- 1. Bench Top :- Made from 18mm thk ISI Marked Pre Laminated MDF Board confirming to IS 14587:1998 with TOP size: 900 x 300 mm. 2. Edge Leaping :- Teak wood half round 18mm wide with polish, OR PVC leaping 18mm with proper edge banding machine. 3. Frame Structure :- As shown in figure made of Mild steel Angle 32 x 32 x 2.5 mm in size 850 (L) x 250 (W) x 432(H) mm. with support & footrest. 4. Foot Rest & support :- Mild steel Angle 32 x 32 x 2.5 mm in full length. 5. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. 6. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

23 23/81 OFFICE CHAIR (Fixed back) SPN NO. :-- SF19E0018 OVERALL SIZE : (H) 950/450* (W) 550*(D) 550mm. METERIAL DETAIL:- 1. Frame :- Mild steel Elliptical (Capsule) pipe 32mm Major Dia x 2mm Thick, frame as shown in figure. (distance between legs 550mm at ground) 2. Seat :- 450 (W) x 450 (D) mm Seat made on 10mm Commercial ply shall be fitted with ploy high density foam 40 mm thick and covered with high quality leatheriest rexin based cloth or other suitable high quality cloth. Seat height 450mm from ground. 3. Back rest :- 450 (W) x 500 (H) mm Seat made on 10mm Commercial ply shall be fitted with ploy high density foam 40 mm thick and covered with high quality leatheriest rexin based cloth or other suitable high quality cloth. 4. Fitting :- Seat shall be fitted over the frame as shown in figure with minimum 3 width wise flat 32 x 5mm at equal distance below the seat with nut bolt (2 flat shown in figure but in chair 3 flats to be used), and back rest seat with suitable good quality fixed arrangement as shown in figure. 5. Handle :- Syncro soft handles with bracket as shown in last figure. 6. Shoes :- P.U / Rubber shoe`s are to be used (4 No s) compulsorily in legs as shown in figure. 7. Painting :- Complete chair frame to be powder coated after 7 tank anti corrosion Treatment. 8. Also refer General Requirements for Welding / Finishing / Packing & etc.

24 24/81 OFFICE CHAIR (Flexible Back) SPN NO. :-- SF19E0019 OVERALL SIZE : (H) 950/450* (W) 550*(D) 550mm. METERIAL DETAIL:- 1. Frame :- Mild steel Elliptical (Capsule) pipe 32mm Major Dia x 2mm Thick, frame as shown in figure. (distance between legs 550mm at ground) 2. Seat :- 450 (W) x 450 (D) mm Seat made on 10mm Commercial ply shall be fitted with ploy high density foam 40 mm thick and covered with high quality leatheriest rexin based cloth or other suitable high quality cloth. Seat height 450mm from ground. 3. Back rest :- 450 (W) x 400 (H) mm half round from top Seat made on 10mm Commercial ply shall be fitted with ploy high density foam 40 mm thick and covered with high quality leatheriest rexin based cloth or other suitable high quality cloth. 4. Fitting :- Seat shall be fitted over the frame as shown in figure with minimum 3 width wise flat 32 x 5mm at equal distance below the seat with nut bolt (2 flat shown in figure but in chair 3 flats to be used), and back rest seat with suitable good quality flexible spring as shown in figure. 5. Handle :- Syncro soft handles with bracket as shown in last figure. 6. Shoes :- P.U / Rubber shoe`s are to be used (4 No s) compulsorily in legs as shown in figure. 7. Painting :- Complete chair frame to be powder coated after 7 tank anti corrosion Treatment. 8. Also refer General Requirements for Welding / Finishing / Packing & etc..

25 25/81 OFFICE REVOLVING CHAIR (High Back) Spn No.: - SF19E0022 W600 x D600 x H1050 / 1150 mm METERIAL DETAIL:- 1. Overall size: Width 600mm Without castors Depth 600mm Height 1050 to 1150mm Adjustability of seat height 450 to 550mm 2. Seat size: 500x500mm approx. 3. Back size: 500x610 (H) approx. 4. Material:- Seat and back should be made up of 12mm thick hot pressed plywood upholstered with fabric and molded Polyurethane foam (high density 40 mm thick), together with molded ABS seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. 5. Handle: The armrest should be one piece Syncro soft handles with bracket as shown in figure and scratch and wear resistant. 6. Castors wheels: The twin wheel castors should be high quality injected molded. 7. Pedestal Assembly: The pedestal should chrome plated steel base casted pedestal, with proper lift mechanism. 8. Upholstery: The seats and backs are to be covered with superior quality latheriest rexin cloth. 9. Finish: All steel components are to be painted after proper anti corrosion pretreatment of surface. 10. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

26 26/81 Steel Bench with Back Rest (With MDF Seat & Back) CODE NO. SF19E0026 Size: L-1500xW-450xH-450/900mm Material Detail:- 1. Frame : ERW Squire pipe 25x25x1.25 four side welded. 2. Seat & Back : 18 mm thick ISI Mark MDF Board with 18mm wide teak wood lapping seat size (L)1500x(D)450mm,Back size (L) 1500x(H) 200 mm 3. Arms : Teak wood arms of size (W) 50*(THK)25*(L) 400 mm and front curved, under side grooved profile matching with pipe. Painted with Black enamel paint. 4. Fitting : Seat shall be fitted with minimum 22 nos. round head steel screws. The backrest shall be fitted on two longitudinal pipe with gap of 75mm.and 12 nos. minimum steel round head screws. In wooden handle 3 nos. Round head steel screws on each side shall be used. 5. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

27 27/81 Schedule-2 CABINETS & BOOKS CASES

28 28/81 CABINET PLAIN SPN NO.:- SF19E0027 OVERALL SIZE : (H) 1980 x (W) 915 x (D) 480mm. 1. Body 2. Self 3. Legs 4. Door stiffener 5. Leaver Road 6. Door Handle MATERIAL DETAILS:- 1. The overall design and appearance of cabinet shall be as per figure mm CR Sheet shall be used of prime quality, Confirming to IS Each shelf be formed such the edges are bend two times at right angle, first bend 30mm and second bend 8mm. 3. Door stiffener frame inside to its full height in top hat section size 100mm width. 4. Lever rod shall be of Ms 12mm round/square bar, or 10mm bright bar. 5. Size of hinges shall be 75mm length x 1.6mm thk. 6. Brackets shall be made of 1.6 mm of CR sheet, riveted or bolted on each side of hinges. 7. Machine made lever plate (patla)with brass bush of good quality or machine made six lever type patla. Patla shall be covered by box covered by box over fitted with round head screws. 8. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zinc alloy body of size(h) 65 x (W) 50mm fitted on four screws or GRACE LOCK. Keys in duplicate with key rings shall provided. 9. Metallic key cover electroplated nickel/chrome on front side of the door shall be provided. 10. For door, die cast chrome plated handle fitted with washer and double nut. 11. Leg height shall be 125 mm x 100 mm. 12. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

29 29/81 CABINET PLAIN SPN NO.:- SF19E0028 OVERALL SIZE (H) 1675 x (W) 840 x (D) 480mm. 1) Door stiffener 2)Lever Rod 3)Door Handle 4)Shelf 5) Legs 6) Body MATERIAL DETAILS:- 1. The overall design and appearance of cabinet shall be as per figure mm CR sheet shall be used of prime quality, Confirming to IS Each shelf shall be formed such the edges are bend two times at right angle, first bend 30mm and second bend 8mm. 4. Door stiffener frame inside to its full height in top hat section size 100mm width. 5. Lever rod shall be of Ms 12mm round/square bar, or 10mm bright bar.\ 6. Size of hinges shall be 75mm length x 1.6mm thk. 7. Brackets shall be made of 1.6 mm of CR. sheet, riveted or bolted on each side of hinges. 8. Machine made leaver plate (patla) with brass bush of good quality or machine made six lever type. Patla. Patla shall be covered by box covered by box over fitted with round head screws. 9. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zinc alloy body of size(h) 65 x (W) 50mm fitted on four screws or GRACE lock. Keys in duplicate with key rings shall provided. 10. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. 11. For door, die cast chrome plated handle fitted with washer and double nut. 12. Leg height shall be 125mm x 100 mm. 13. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

30 30/81 CABINET PLAIN MINI SPN NO.:- SF19E0030 OVERALL SIZE : (H) 915 x (W) 610 x (D)380 mm. 1) Door stiffener 2)Lever Rod & Plate 3)Door Handle 4)Shelf 5) Legs 6) Body MATERIAL DETAILS:- 1. The overall design and appearance of cabinet shall be as per figure mm CR sheet shall be used of prime quality, Confirming to IS Each shelf shall be formed such the edges are bend two times at right angle, first bend 30mm and second bend 8mm. 4. Door stiffener frame inside to its full height in top hat section size 100mm width. 5. Lever rod shall be of Ms 12mm round/square bar, or 10mm bright bar. 6. Size of hinges shall be 75mm length x 1.6mm thk. 7. Brackets shall be made of 1.6 mm of CR sheet, riveted or bolted on each side of hinges. 8. Machine made leaver plate (patla) with brass bush of good quality or machine made six lever type. Patla. Patla shall be covered by box covered by box over fitted with round head screws. 9. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zine alloy body of size(h) 65 x (W) 50mm fitted on four screws or GRACE lock. Keys in duplicate with key rings shall provided. 10. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. 11. For door, die cast chrome plated handle fitted with washer and double nut. 12. Leg height shall be 125mm x 100 mm. 13. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

31 31/81 CABINET PLAIN WITH ONE LOCKER SPN NO.:- SF19E0031 OVERALL SIZE: (H) 1980 x (W) 915 x (D) 480mm. 1) Door stiffener 2)Lever Rod 3)Door Handle 4)Shelf 5)locker. MATERIAL DETAILS:- 1. The overall design and appearance of cabinet shall be as per figure mm CR sheet shall be used of prime quality, Confirming to IS Each shelf shall be formed such the edges are bend two times at right angle, first bend 30mm and second bend 8mm. 4. Door stiffener frame inside to its full height in top hat section size 100mm width. 5. Lever rod shall be of Ms 12mm round/square bar, or 10mm bright bar. 6. Size of hinges shall be 75mm length x 1.6mm thk. 7. Brackets shall be made of 1.6 mm of CR sheet, riveted or bolted on each side of hinges. 8. Machine made leaver plate (patla) with brass bush of good quality or machine made six lever type Patla. Patla shall be covered by box covered by box over fitted with round head screws. 9. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zinc alloy body of size (H) 65 x (W) 50mm fitted on four screws or GRACE lock. Keys in duplicate with key rings shall provided. 10. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. 11. For door, die cast chrome plated handle fitted with washer and double nut. 12. Leg height shall be 125mm x 100 mm. 13. Locker size (W) 420 x (H) 254 shall be provided, Each licker shall be provided with box type door with die cst chrome plated handle. Lock shall be plate type with 150mm sliding plate arrangement or 2 nos. 25mm pin rod/ 2nos. 30mm wide plate sliding arrangement. 14. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc. CABINET PLAIN WITH ONE LOCKER

32 32/81 SPN NO.:- SF19E0032 OVERALL SIZE: (H) 1675 x (W) 840 x (D) 480mm. 1) Door stiffener 2)Lever Rod 3)Door Handle 4)Shelf 5)locker. MATERIAL DETAILS:- 1. The overall design and appearance of cabinet shall be as per figure mm CR sheet shall be used of prime quality, Confirming to IS Each shelf shall be formed such the edges are bend two times at right angle, first bend 30mm and second bend 8mm. 4. Door stiffener frame inside to its full height in top hat section size 100mm width. 5. Lever rod shall be of Ms 12mm round/square bar, or 10mm bright bar. 6. Size of hinges shall be 75mm length x 1.6mm thk. 7. Brackets shall be made of 1.6 mm of CR sheet, riveted or bolted on each side of hinges. 8. Machine made leaver plate (patla) with brass bush of good quality or machine made six lever type. Patla. Patla shall be covered by box covered by box over fitted with round head screws. 9. For locking brass body Godrej type cabinet lock or cabinet lock 6leaver die cast zine alloy body of size(h) 65 x (W) 50mm fitted on four screws or GRACE lock. Keys in duplicate with key rings shall provided. 10. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. 11. For door, die cast chrome plated handle fitted with washer and double nut. 12. Leg height shall be 125mm x 100 mm. 13. Locker size (W) 420 x (H) 254 shall be provided, Each licker shall be provided with box type door with die cst chrome plated handle. Lock shall be plate type with 150mm sliding plate arrangement or 2 nos. 25mm pin rod/ 2 nos. 30mm wide plate sliding arrangement. 14. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

33 33/81 CABINET WARDROBE Spn No.: SF19E0033 OVERALL SIZE: (H) 1980 x (W) 900 x (D) 560mm. NOTE :- Detail are given in the Annexure 1.Door Stiffener 2. Door Handle 3.Locker 4. Shelf 5. Body The overall design and appearance of cabinets shall be as per their respective figure. The 0.8 mm CR sheet used shall be of prime quality Confirming to IS-513, each shelf shall be formed such the edges are bend two times at right angle, first bend 30mm and second bend 8mm. Size of hinges shall be 75mm length x 1.6mm thk. Brackets shall be made of 1.6mm of MS. sheet, riveted of bolted on each side of hinges. Machine made lever plate (patla ) withy brass bush of good quality or machine made six lever type Patla. Patla shall be covered by box covered by box over fitted with round head screws. Metallic key cover electroplated nickel/chrome on fount side of the door shall be provided. For door, die cast chrome plated handle ritted with washer and double nut. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc. For Spn No. SF19E0034 Top shelf of cabinet shall be fitted at 914 mm from top. This portion called wardrobe shall be provide with partition in full length. On left side of wardrobe one locker with 250mm height. Locker shall be provided with box type door with die cast chrome plated handle. Lock shall be plate type with 150mm slidding plate/25 mm pin rod/ 30mm plate sliding arrangement. On the right side of wardrobe one hanger pipe of 18x1.2mm thick chrome plated shall be provided. One mirror ( 1200x300mm) of good quality ATUL/modi make, fitted on left door from outside in pressed steel section. Leg height shall be 125x100 mm. Please refer General requirements. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

34 34/81 COMPONENT DETAILS S.No. Spn No.. Type Size mm Sheet No. of Hinges Shelf No. (HxWxD) & Brackets & Depth 01. SF19E0028 CABINET PLAIN 1980x915x mm 6 4 nos.x/400mm 02. SF19E0029 CABINET PLAIN 1675x840x mm 6 4 nos.x/400mm 03. SF19E0030 CABINET PLAIN 1270x760x mm 4 3 nos.x/355mm 04. SF19E0031 CABINET PLAIN 915x610x mm 2 2 nos.x/330mm 05. SF19E0032 CABINET PLAIN 1980x915x mm 6 4 nos.x/400mm WITH ONE LOCKER 06 SF19E0033 CABINET PLAIN WITH 1675x840x mm 6 4 nos.x/400mm ONE LOCKER 07 SF19E0034 WARDROBE 1980X900X mm 6 3 nos.x/500mm 08 Please Refer General Requirements.

35 35/81 STEEL BOOK CASE Spn No.:- SF19E0035 OVERALL SIZE : (H) 1675x(W) 840x (D) 380mm. MATERIAL DETAILS :- 1. The Design of this steel Bookcase shall be as shown above. 2. Sheet CR prime 0.80 mm thick Confirming to IS-513 with latest Amendment 3. Compartment- 4, equal in size. 4. Six leaver locks of high quality in each shutter operated by one key, supplied with key ring. 5. Chrome plated, metallic handles 2 No s on each shutter from outside. 6. Plane glass, 4mm thick in each shutter fitted in suitable frame from inside & P.U/rubber packing should be provided around the glass fitting. 7. Shutter sliding on ball bearing, 2 No s in each door with suitable system / double roller system. 8. One additional plate of 127mm height x 830mm width shall be provided on lower side. 9. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

36 36/81 Schedule -3 LOCKERS, CABINETS & SAFE

37 37/81 INDUSTRIAL LOKCER CABINET (9 Lockers) SPN NO.:- SF19E0036 OVERALL SIZE: (H)1800 x (W) 900 x (D) 400mm Body 0.8 mm CR SHEET Confirming to IS Handle Nickel/ Chrome plated. 3. Key hole, 4. Door stiffener. 5. Label Holder 6. Leg. METERIAL DETAILS:- 1. The design of this industrial locker cabinet having 9 locker shall be as shown above. 2. Six of locker doors shall be 260x550mm height. 3. Separate locking system in each locker. Locks of 6 lever of good quality with duplicate keys & Key rings. In addition manual locking lache to be provided for external lock. 4. Label Holder Nickel/chrome plated or Aluminum on each door. 5. Two hinges 50x1.0mm thick in each door, along with two brackets of 1.25mm thick. 6. Door stiffener in side to its full height in top hat section of suitable size. 7. Please refer General Requirements. 8. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

38 38/81 CASH BOX SPN NO.: - SF19E0039 OVERALL SIZE: (H) 250 X (W) 380 X (D) 300mm. MATERIAL DETAILS :- 1. The overall design & appearance of this cash box shall be as shown above, 2. Cash box body CR sheet, 1mm thick. 3. Upper edge bending 20mm as shown in figure and second edge bending 8mm approx. 4. A removable tray of 1mm thick CR sheet Confirming to IS-513 with four partitions. Width & depth shall be 200 mm rest of the width shall be kept open for keeping currency notes in bottom compartment. 5. Door closing shall be made with machine made patla provided with quality 6-lever lock in the lid as per arrangement provided in the steel cabinets, with Nickel/Chrome plated key cover. 6. Strong chrome plated/nickel plated/handle on door sheet 1.60mm thick for door. 7. Key cover of best quality Nickel or chrome Plated. 8. Hinges : 2Nos., size 50x1.25mm thick. 9. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

39 39/81 Schedule -4 TIN BOX & ANAJ KOTHI

40 40/81 TIN BOX Spn No.:- SF19E0043 OVERALL SIZE : (L) 900 (W) 450 (H) 350 mm. 1. The over all desigh & appearance of this tin box shall be as shown in Spn No. SF19E0041, except the dimensions which in this case (L) 900 x (W) 450 x (H) 350 mm. 2. Other constructional details shall be similar to that as tin box Spn No. SF19E0041 Schedule -5 RACKS, & COTS

41 41/81 ANGLE IRON RACK Spn No. :- SF19E0049 OVERALL SIZE: (H) ) 900X (W) ) 900X (D) 380mm. 1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note: Details are given in the Annexure

42 42/81 ANGLE IRON RACK Spn No. :- SF19E0050 OVERALL SIZE: (H) ) 900 (W) ) 900 (D) 450mm. 1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note: Details are given in the Annexure

43 43/81 ANGLE IRON RACK Spn No. :- SF19E0051 OVERALL SIZE : (H) 1800 (W) ) 900 (D) 380mm. 1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note: Details are given in the Annexure

44 44/81 ANGLE IRON RACK Spn No. :- SF19E0052 OVERALL SIZE : (H) 1800 (W) 900 (D) 450mm. 1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note : Details are given in the Annexure

45 45/81 ANGLE IRON RACK Spn No. :- SF19E0053 OVERALL SIZE : (H) 1950 (W) 900 (D) 450mm. 1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note : Details are in the Annexure

46 46/81 ANGLE IRON RACK Spn No. :- SF19E0054 OVERALL SIZE : (H) 2100 (W) 900 (D) 450mm. 1) Shelf 2) Angle Iron 3) Bolts 4) Corner Plates 5) Plastic Shoe. Note : Details are given in the Annexure

47 47/81 Angle Iron Rack Annexure 1. The over all design & appearance of this Angle iron rack shall be as shown in item wise figure. 2. Angle iron 32x32x mm thick (Non slotted) M.S angle shall be used, holes for 8 mm dia bolt to be drilled at location of shelf fitting (No extra holes to be provided), joints in angle iron Leg shall not be allowed it should be solid single peace. 3. Each shelf shall be made from 0.8 mm thick CR sheet. Shelf shall be formed such that lengthwise edges are bent two times at right angles. First bend shall be 25 mm & second bend 8mm. Widthwise edges are to be bent only one time. 4. Press cut shelf corner plate s 8nos. in upper shelf and 8no. in lower shelf of 0.80 mm thick CR sheet shall be used in all racks, Racks having 5 shelf or more additional 8 corner plates at center shelf to be provided. (Refer Corner plate Location in below shown table) 5. Galvanized nut both of hexagonal hand 8mm dia x 10mm long. 6. No sharp edges on angle iron ends shall be allowed, four plastic shoes of appropriate size shall be provided for legs. 7. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc. Sr. No. Specification No. Size (mm) No. Shelf Corner plate Location shelf wise from top 1 SF19E H x 900W x 380D 3 1 ST & 3 rd 2 SF19E H x 900W x 450D 3 1 ST & 3 rd 3 SF19E H x 900W x 380D 5 1 ST & 3 rd & 5 TH 4 SF19E H x 900W x 450D 5 1 ST & 3 rd & 5 TH 5 SF19E H x 900W x 450D 6 1 ST & 3 rd & 6 TH 6 SF19E H x 900W x 450D 7 1 ST & 4 TH & 7 TH

48 48/81 ANGLE IRON COT (TAKHAT) WITH PLY Spn No. : - SF19E0055A, SF19E0055B OVERALL SIZE A : (L) 1950 x (W) 900 X (H) 450mm with 25mm ISI Marked Plywood B : (L) 1950 x (W) 900 X (H) 450mm with 18mm ISI Marked Plywood SPECIFICATION SF19E0055 A:- 1. Design & appearance of the cot shall be as per shown in the fig. 2. Angle iron frame, 32 x 32 x 3 mm thick. 3. Widthwise Angle iron support, 3 No s 25x25x 2.5mm, shall be at equal distance. 4. Head bow and foot bow Angle Iron Frame 35x35x5 5. Provided with arrangement for Mosquito Net Poles (Poles are not to be supplied) 15mm dia x x1mm thick x 75 mm length 6. Angle Iron frame sixe L 1950 x W 900 mm 7. Height of angle iron frame from ground level -450mm. 8. Total length including head/foot Leg bow 1980mm. 9. ISI Marked Plywood, (L 1944 x W 894 x 25 mm) Phenol Bonded BWP Grade as per IS 710: Also refer General Requirements for Welding / Painting / Finishing / Packing & etc. SPECIFICATION SF19E0055 B :- 1- ISI Marked Plywood, (L 1944 x W 894 x 18 mm) Phenol Bonded BWP Grade as per IS 710: other details shall be as per Specification no. SF19E0055 A

49 49/81 ANGLE IRON COT (strip flats) Spn No. : - SF19E0056 OVERALL SIZE : (L) 1950/1870 (W) 900 (H) 450mm SPECIFICIATION : - 1. Design and appearance as shown in fig. 2. Angle iron frame 32 x 32 x 3mm Lengthwise angle iron support at equal distance made of M.S Angle 25 x 25 x 3 mm 4. 13nos strips widthwise made out of 1.0mm. thick CR sheet having width 100mm formed type first bend 12mm second bend 8mm. 5. Head bow and foot bow pipe: ERW square pipe 40 x 40 x 1.5 mm thick (weight=1.7 kg/m). 6. Head bow /foot bow pipe support in widthwise one in each side size ERW square pipe 40 x 40 x 1.5 mm thick (weight=1.7 kg/m). 7. Head bow height = 650mm & support at 350mm from top, 8. Leg Bow height = 600mm & support at 300mm from top. 9. Head bow /foot bow vertical pipe support ERW square pipe 40 x 40 x 1.5 mm thick, 2 No s on each side at equal distance. 10. Folding arrangement of head bow/foot bow by flat iron 18x4mm duly riveted. 11. Mosquito net poles support of 12mm i.d. pipe 1mm thick. 75 long duly plugged from bottom. 12. Plastic / rubber shoe on legs. 13. Height of angle iron main frame from ground level 450mm. 14. Total length of bed including head bow/foot bow 1950mm. 15. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

50 50/81 ANGLE IRON COT (Plywood) Spn No. : - SF19E0057 OVERALL SIZE : (L) 1950/1870 (W) 900 (H) 450mm SPECIFICIATION : - 1. Design and appearance as shown in fig. 2. Angle iron frame 32 x 32 x 3mm widthwise angle iron support at equal distance made of M.S Angle 25 x 25 x 3 mm 4. ISI Marked Plywood, (L 1864 x W 894 x 18 mm) Phenol Bonded BWP Grade as per IS 710: Head bow and foot bow pipe: ERW square pipe 40 x 40 x 1.5 mm thick (weight=1.7 kg/m). 6. Head bow /foot bow pipe support in widthwise one in each side size ERW square pipe 40 x 40 x 1.5 mm thick (weight=1.7 kg/m). 7. Head bow height = 650mm & support at 350mm from top, Leg Bow height = 600mm & support at 300mm from top. 8. Head bow /foot bow vertical pipe support ERW square pipe 40 x 40 x 1.5 mm thick, 2 No s on each side at equal distance. 9. Folding arrangement of head bow/foot bow by flat iron 18x4mm duly riveted. 10. Mosquito net poles support of 12mm i.d. pipe 1mm thick. 75 long duly plugged from bottom. 11. Plastic / rubber shoe on legs. 12. Height of angle iron main frame from ground level 450mm. 13. Total length of bed including head bow/foot bow 1950mm. 14. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

51 51/81 Schedule -6 COMPUTER FURNITURE

52 52/81 General Requirements for Schedule -6 (Computer Furniture) For Suppliers 1. The sizes written in the specifications are cut size while finished sizes are given in the details drawing. 2. Tolerance in the finished products wherever not specified shall be as follows :- a. Wooden Section width mm and Thickness mm. b. Overall dimensions + 10 mm. c. Pipe thickness - As per IS. 3. Finishing & Workmanship in the furniture is of prime importance and must be of high standard. 4. Before polishing, the surface should be finished with sand paper and properly grain filled. 5. Polishing shall be done properly, preferably Touch Wood Polish. 6. Teak wood used in furniture shall be naturally seasoned without any defects like dead knot, cracks, dry root, upset grains, twisted fibre etc. On face side and edges of the furniture, sap wood shall not be used. 7. Before delivery to the consignee, the unit shall ensure that the product is as per specification and all the accessories are provided with the product. 8. The design and drawings of the furniture are not to the scale. For Consignees 1. Please do not accept damaged / broken furniture. 2. Before accepting the delivery of furniture, please ensure that the finishing and polishing / painting of the furniture is not affected during transportation. 3. Please do ensure, before accepting delivery, the each furniture item Inspected by Inspecting Authority and Supplier s Metal / Paper Stickers having following details :- - Suppliers Name / Address. - Supply Order No. / Date. - Date of Supply. 4. Please do not accept any furniture without Inspection Certificate and Seal of Inspecting Authority / Suppliers Sticker, in order to ensure quality of furniture, as per specification.

53 53/81 COMPUTER CHAIR MID BACK Spn No.. : - SF19E0060A, SF19E0060B Overall Size: 600 x 600 x 850 / 950 mm SPECIFICATIONS: SF19E0060 (A) SF19E0060 (B) With Arm Rest / Handle Without Arm Rest / Handle 1. Overall size : Width 600mm Depth 600mm Height 850 to 950mm Adjustability of seat height 400 to 500mm 2. Seat size: 450 x 450mm approx. 3. Back size: 430 x 500 (H) approx. 4. Material: Seat and back should be made up of 12mm thick hot pressed plywood upholstered with fabric and molded Polyurethane foam (high density 40 mm thick), together with molded ABS seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. 5. Arm Rest: The armrest should be one piece Syncro soft handles with bracket as shown in another figure and should be scratch and wear resistant. 6. Castors wheels: The twin wheel castors should be high quality injected molded. 7. Pedestal Assembly: The pedestal should chrome plated steel base casted pedestal, with proper lift mechanism. 8. Upholstery: The seats and backs are to be covered with good quality matty / tapestry cloth. 9. Finish: All steel components are to be painted after proper anti corrosion pretreatment of surface. 10. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.

54 54/81 COMPUTER CHAIR WITH HANDLES (Low Back) CODE NO. SF19E0061A & SF19E0061B Overall Size: 600 x 600 x 750 / 850 mm SPECIFICATIONS: SF19E0061 (A) SF19E0061 (B) With Arm Rest / Handle Without Arm Rest / Handle 1. Chair shall be as shown in the figure. 2. Seat: size shall be 430 x 430 mm on 10 mm thick moulded comm. ply with 40 mm thick high density foam covered with tapestry. 3. Back rest: size shall be 430 x 350 mm on 10 mm thick moulded comm. ply with 40 mm thick high density foam covered with tapestry. The height of back rest shall be 900 & 500 mm for top and bottom edges respectively. The back rest shall be provided with lifting arrangement on flat iron & helical spring. 4. Arm Rest: The armrest should be one piece Syncro soft handles with bracket as shown in another figure and should be scratch and wear resistant. 5. Castors wheels: The twin wheel castors should be high quality injected molded. 6. Pedestal Assembly: The pedestal should chrome plated steel base casted pedestal, with proper lift mechanism. A Central spindle of 25 mm dia rod without threads shall be provided with revolving arrangement. The adjustable height of chair shall be from 450 to 550 mm. 7. Upholstery: The seats and backs are to be covered with good quality matty / tapestry cloth. 8. Finish: All steel components are to be painted after proper anti corrosion pretreatment of surface. 9. Also refer General Requirements for Welding / Painting / Finishing / Packing & etc.