Part# 85200, 86200, 85095, 86095, TC200,TT200,TC095,TT095

Size: px
Start display at page:

Download "Part# 85200, 86200, 85095, 86095, TC200,TT200,TC095,TT095"

Transcription

1 Part# 85200, 86200, 85095, 86095, TC200,TT200,TC095,TT095 Bag Hardware: (8) 5/16 x 1 ½ Allen flat head (14) 3/8 x 1 Hex bolt G5 (2) ½ x 2 ½ Hex Bolt G5 (6) 5/16 flange nuts (14) 3/8 flange nuts (2) ½ stove lock nuts (6) ½ steel washers (6) ½ brass washers (14) 3/8 steel washers (1) Bump stop w/ 3/8 thread (2) 3/8 wing nuts (can carrier only) (3) #12 x 3/4 (for tail light) (2) 5/16 x 1 Hex bolt (1) 2 x 2 Self adhesive pad TC095 & TT095 additional following items (1) 1/4 x 1 Allen button head (1) 1/4 square nut Box hardware: (1) Carrier rack (1) Left body reinforcement bracket (1) Right body reinforcement bracket (1) Hinge plate 16 x8 (1) Lower Support Brace (2) tail gate spacer plates (1) Striker landing mount (1) Tire hub plate (1) T-handle *Bracket box contents for Tire/Can carrier (2) Gas can L- brackets (can carrier only) (2) Threaded rod (can carrier only) (1) Lock bar Tools needed: *Set of hand box wrenches standard * T40,T45,T50 torx bits *3/8 rachet and extensions *Standard set of 3/8 sockets * 3/16 & 7/32 allen wrench or sockets * 7/16 center punch * Ball pin hammer *1/8 drill bit, 7/16 drill bit or Uni-Bit. *Angle drill air or electric. *Hacksaw *Bench vise Option tools: * Hobby knife * 1/8 to ½ Uni-bit * Die grinder Install time is about 120 minutes to?, depending on your skills. Check to make sure all hardware is present before you start. We recommend a extra helper to help speed up the install. Copy of these instructions are also on our web * Please note these instructions cover TJ & YJ models and some images may very from your year and model. Tire/Can carrier is design to use Lip style Gerry cans. Optional non-lip can adapter available. page 1 of 5 Revision 0203 O-R FAB,Inc. 2003

2 (1) Remove stock tire carrier and third third brake light. * Hint if you have Dual Top option you ll need to remove the hard top to remove the soft top bow assembly to access area at roll bar foot. (2) Remove seat belt retractor from roll bar. Use T50 torx. (3) Remove Tail gate with hinges attached. Using T40 torx. Lay flat and remove hinges from tail gate.*hint use a hobby knife to cut the factory paint around the bolts. (4) Pull under fender liner back under rear quarter panel. Pull out one plastic rivet. (5) Remove tail light assembly and reach under body to disconnect light wiring plug. (6)Remove and save the roll bar mount bolts with T45 torx. *Hint use a hobby knife to cut the factory paint around the bolts. (7) Remove the factory tail gate striker mount with T40 torx. Save bolts for installation. (7A) Now anchor the bracket in a vise and with a small drill bit drill out the rivet and remove the striker post and the flat nut. Save for installation. (7B) Now anchor the striker post in a vise and cut 1/4 from the thread for install. (8) Install both left and right body reinforcement brackets to the base of the roll bar and snug against back wall of body. (9) Install the stock bolts removed in step 6,but don t tighten at this time page 2 of 5

3 (10) Now center punch holes starting with left rear body bracket make sure the bracket is snug flush to back of the body. Repeat center punches for right bracket. (11) With a 1/8 drill bit and a Angle drill begin pilot drilling holes. Then change drill bit to 7/16 and enlarge holes. *Hint a good UNI-BIT from your local hardware store works best. (12) Install striker plate using 3/8 x1 hex head bolt and 2 x 3/8 flange nuts. Snug but don t tighten yet. (12A)YJ only Install (1x) 1/4 x 1.0 Allen button head bolt and 1/4 square nut to factory mount hole. Snug but don t tighten yet. (13) Slide the flat nut and install striker post from step 7A/B. Use 2x ½ flat washers under post.. (14) Now install the Carrier hinge plate and tail gate hinges using (4x) 5/16 x1.5 Flat head allen bolts and 5/16 flange nuts. Align with tail light cut out and snug bolts don t tighten at this time. Adjustments may be needed later. *Hint you can attach hinges to tail gate first by placing spacer plates between hinge and tail gate (15) Now place (2x) 5.75 spacer plates between tail gate and hinge and use (4) 5/16 x1.5 flat head allen bolts. (16) Now install tail gate back up to body and have extra help hold in place. *Note you will need to align and adjust tail gate with body. Make sure to center tail gate so striker post matches.once aligned snug down bolts enough to hold in place. page 3 of 5

4 (17) Now begin installing body reinforcement bracket bolts starting with factory bolts on left side bracket and (12x) 3/8 x 1.0 bolts and 3/8 flange nuts supplied. Repeat for right side. (18) Center punch and drill out the 3 holes on the hinge plate and install (3x) 3/8 x1 Hex bolts with 3/8 flange nuts. Snug but don t tighten. (19)Install the lower hinge plate support bar under the right rear body as shown here (1x)3/8 x1 bolt and flange nut through factory bracing. (20) Now with extra help install the Carrier to the hinge plate using (2x) ½ x 2.5 bolts,(2x) ½ washers & (6x) ½ brass washers. Place 1 brass washer above carrier leg and 2 below leg. Install bolts. but don t tighten. *Hint sharpen the ½ bolts with a grinder to ease installation through powder coat. (21) Align the Carrier with the striker plate on the left side. Check to see if it closes and alignment is correct if not loosen and adjust the hinge plate. Once alignment is achieved Begin tightening Hinge bolts and tail gate bolts. *Note on some vehicles striker plate maybe to close. This is due to factory holes out of tolerance. You ll need to remove the striker landing plate and enlarge holes with a die grinder. page 4 of 5

5 (22) Tighten all bolts and adjust tail gate striker post to correct depth. Install the lower bump stop. Peel and stick 2 x 2 stainless pad to tail gate just where bump stop will make contact with tail gate Adjust bump stop to just touch pad on tail gate. (23) Fold back carpet and reinstall rear seat belt retractor Reinstall and plug in rear tail light using #12x3/4 bolts. Install Lock bar to the top of the spin mount on the rack using (2)5/16 x1 hex bolts and 5/16 Flange nuts. (24) )Tire/Can carrier only install your gas cans by inserting the lip of the bottom of the Gerry can into the clip of the lower frame of the rack and anchor using 3/8 x 8 threaded rod,l-bracket and wing nut. *Note you can install a Hi-Lift jack to the upper or lower holes inside the tire carrier with 3/8 x 1.5 bolts you can get from your local hardware store. Now you ready for the trails! Lubricate once per month pivots and threaded bolt holes with Silicone Spay you can purchase from your local Auto parts store. *Note max. Load rating closed is 200lbs. if total weight of your Tire,wheel and cans exceed we recommend not mounting Jack to carrier. WARRANTY STATEMENT O-R FAB, INC. Warrants all products against defects in material and workmanship for a period of 180 days from the date of proof of purchase receipt. Warranty shall not extend to any piece of merchandise or part thereof which has been subjected to improper installation, misuse or neglect. Warranty is limited to replacing or repairing part or parts which are defective and are returned to O-R FAB, Inc. Freight prepaid. No returns will be accepted without RMA #. Finishes (powder coating) has a 3 month warrantee. Warranty DOES NOT COVER RUST. page 5 of 5

JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS

JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS TOOLS NEEDED 3/16 Allen Wrench 1/2 Socket or wrench 10mm Socket Flat head screwdriver HARDWARE 5/16 x 3/4 button heads (14) 5/16 x 1 button heads (8) 5/16

More information

ALUMINUM HEADKNOCKER RACK P/N HKRS4-1 / HKRS5-1

ALUMINUM HEADKNOCKER RACK P/N HKRS4-1 / HKRS5-1 ALUMINUM HEADKNOCKER RACK P/N HKRS4-1 / HKRS5-1 Package Contents: PARTS (1) CROSS BAR (2) LEGS WITH FEET (2) T BRACKETS (1) SCREEN ASSEMBLY (2) SCREEN L MOUNTS (2) LOWER SCREEN MOUNTS (2) LOAD SECURE POSTS

More information

SLW 6 Channel Letter Brake. User Guide. Operation and Mounting Instructions

SLW 6 Channel Letter Brake. User Guide. Operation and Mounting Instructions SLW 6 Channel Letter Brake User Guide Operation and Mounting Instructions Scope This document describes the operation and mounting instructions for the SLW 6" Channel Letter Brake. Please read all instructions

More information

2 SHOULDER BOLTS RIGHT AND LEFT HINGE USE 4 EXISITING DOOR BOLTS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER.

2 SHOULDER BOLTS RIGHT AND LEFT HINGE USE 4 EXISITING DOOR BOLTS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. Page 1 of 12 NISSAN 350Z 2003-2004 THIS KIT INCLUDES: 8 BOLTS WITH WASHERS 2 SHOCKS 780 PSI 2 PINS 2 SHOULDER BOLTS RIGHT AND LEFT HINGE USE 4 EXISITING DOOR ASSEMBLY BOLTS TOOLS REQUIRED FOR INSTALLATION:

More information

Thor Audi A4/S4 Skid Plate Installation Instructions

Thor Audi A4/S4 Skid Plate Installation Instructions Thor Audi A4/S4 Skid Plate Installation Instructions Parts List: 1 Aluminum Skid Plate 2 Aluminum Side Wings 10 10mm Flat Washers 3 8mm Flat Washers 3 8mm Speed Clips 2 10x40mm Bolts 3 8x35mm Bolts 2 Rivet-nuts

More information

TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER.

TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. THIS KIT INCLUDES: 16 M8-1.25X30MM BOLTS WITH WASHERS 2 SHOCKS 565 PSI RIGHT AND LEFT HINGE ASSEMBLY 2 SHOULDER BOLTS 2 PINS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. 7/23, 10MM,

More information

Models 2230 and 2240

Models 2230 and 2240 Models 2230 and 2240 Overview... 2 Tools Needed... 2 Hardware...3 Assembly... 4-13 Installation... 14 Drawer Removal... 15 Operation... 15 Maintenance... 15 Accessories... 16 Limited Warranty... 16 Perform

More information

Installation Instructions Tailgate Rack Bracket

Installation Instructions Tailgate Rack Bracket Installation Instructions Tailgate Rack Application: Jeep Wrangler 1986 Current Part Number: 41411 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question. Click here for more

More information

CORVETTE CORVETTE REV: Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending.

CORVETTE CORVETTE REV: Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending. CORVETTE 2005-2006 CORVETTE 2005-2007 REV: 7-2-07 Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending. Page 1 of 12 CORVETTE C6 2005-2007 THIS KIT INCLUDES:

More information

Sheet Metal Brake Plans for a 6' Sheet Metal Brake

Sheet Metal Brake Plans for a 6' Sheet Metal Brake Sheet Metal Brake Plans for a 6' Sheet Metal Brake,1752'8&7,21 Thank you for purchasing the sheet metal brake plans. The plans include a complete list of material needed and easy to follow steps to build

More information

Medium HoneyBadger Chase Rack Installation Instructions

Medium HoneyBadger Chase Rack Installation Instructions PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading

More information

Installation Instructions SRC OFF ROAD ROOF RACK Wrangler,97-06 Wrangler,04-06 Unlimited Part # s 76711,76713,76715)

Installation Instructions SRC OFF ROAD ROOF RACK Wrangler,97-06 Wrangler,04-06 Unlimited Part # s 76711,76713,76715) NOTE: Please read this information entirely before installing. To obtain correct installation, we recommend you follow these step-by-step instructions carefully. Please take care when installing this product

More information

Master Your Terrain. (307)

Master Your Terrain. (307) Master Your Terrain (307) 775 9565 www.tntcustoms.com Rear Swing-out Tire Carrier Jeep TJ/LJ Installation Instructions Congratulations for purchasing a T&T Customs, Inc. Rear Swing-out Tire Carrier for

More information

Introduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions

Introduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop

More information

Installation Instructions Hinged Roof Rack

Installation Instructions Hinged Roof Rack Installation Instructions Hinged Roof Rack Application: Jeep Wrangler Unlimited 2004 - Current Part Number: 41435-01 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question

More information

OTHER TOOLS MAY BE NEEDED DEPENDING ON YOUR VEHICLE.

OTHER TOOLS MAY BE NEEDED DEPENDING ON YOUR VEHICLE. THIS KIT INCLUDES: 16 M8-1.25X40MM BOLTS WITH WASHERS 2 SHOCKS 720 PSI RIGHT AND LEFT HINGE ASSEMBLY 2 SHOULDER BOLTS 2 PINS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. 10MM, 11MM,

More information

FENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description

FENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description ` FENDER FLARE Part No: FFC3002S TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE FENDER FLARE CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required

More information

THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE

THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE Sal es@lambodoorscanada. com 2407A Kal adarave,ottawa,on K1V 8B9 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE 2 SHOCKS 565 PSI 2 SHOULDER

More information

Installation Instructions:

Installation Instructions: NOTE: Carefully read entire instructions thoroughly before attempting to install this part. (SB76904) Parts Included Qty 94-241CA001 Front Upright: Drvr 1 94-241CA002 Front Upright: Pass 1 94-241CA003

More information

CORVETTE Page 1 of 12 CORVETTE C

CORVETTE Page 1 of 12 CORVETTE C CORVETTE 2005-2006 Page 1 of 12 CORVETTE C5 1997-2004 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE ASSEMBLY WIRE LOOM 2 SHOCKS 565 PSI 2 SHOULDER

More information

STYLE BAR & TONNEAU COVER INSTALLATION

STYLE BAR & TONNEAU COVER INSTALLATION STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT

More information

PRORAC CONTRACTOR SERIES UNIVERSIAL STEEL TRUCK / CAP RACK INSTALLATION INSTRUCTIONS

PRORAC CONTRACTOR SERIES UNIVERSIAL STEEL TRUCK / CAP RACK INSTALLATION INSTRUCTIONS PRORAC CONTRACTOR SERIES UNIVERSIAL STEEL TRUCK / CAP RACK INSTALLATION INSTRUCTIONS 1000 Lb. Capacity Bed Mount 750 Lb. Capacity Cap Mount Package Contents: Parts Hardware (4) Legs (12) 3/8-16 x 1-1/4

More information

RBP-1215B-RX DODGE RAM QUAD CAB RX3

RBP-1215B-RX DODGE RAM QUAD CAB RX3 RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION Customer Support TM FENDER FLARE INSTALLATION TG-FF8C4108 IMPORTANT TYGER only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation

More information

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS Thank you for your purchase of the C4 Fabrication s 5th Gen 4Runner Rock Sliders! This product was carefully crafted to ensure a perfect

More information

Installation Instructions Kit, Base Rail Bracket Part # 31413

Installation Instructions Kit, Base Rail Bracket Part # 31413 Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: End User: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating

More information

ASSEMBLY INSTRUCTIONS FOR HAULER II SERVICE BODY A RACK

ASSEMBLY INSTRUCTIONS FOR HAULER II SERVICE BODY A RACK ASSEMBLY INSTRUCTIONS FOR HAULER II SERVICE BODY A RACK T12USBA-1 shown above Package Contents: HARDWARE KIT PARTS (4) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLY (20) 3/8-16 x 2 CARRAIGE

More information

CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf

CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf HPA Motorsports Inc. 604-888-7274 www.hpamotorsport.com CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf Congratulations on the purchase of your Club-Sport Roll Bar from HPA Motorsports! The engineering elements

More information

Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide

Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can

More information

Dual Arm Tilt LCD Mount

Dual Arm Tilt LCD Mount Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,

More information

Installation Instructions Cage Kit JK Unlimited (4-Dr) Part # 76902

Installation Instructions Cage Kit JK Unlimited (4-Dr) Part # 76902 Please read instructions entirely before installing this product. Drilling is required to install this part. Parts Included Qty Parts Included Qty Driver Front Upright 1 Pass Side Drill Template (7289)

More information

Custom 3-Point Seatbelt Installation Guide for: Corvette

Custom 3-Point Seatbelt Installation Guide for: Corvette Custom 3-Point Seatbelt Installation Guide for: 1963-67 Corvette Note: The information enclosed in this installation guide is to be used as merely an outline to assist you during the process of installation.

More information

USSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS

USSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS 1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:

More information

SEATBELT SOLUTIONS, LLC.

SEATBELT SOLUTIONS, LLC. Custom 3-Point Seatbelt Installation Guide for: 1963-67 Corvette Note: The information enclosed in this installation guide is to be used as merely an outline to assist you during the process of installation.

More information

Models 2130 and 2140

Models 2130 and 2140 Models 2130 and 2140 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-10 Installation...11 Operation... 11 Maintenance... 12 Accessories...12 Limited Warranty... 12 Perform the following sequence

More information

WARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD!

WARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD! WARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD! THIS KIT INCLUDES: 4 M8-1.25X30MM BOLTS WITH WASHERS 12 M8-1.25X40MM BOLTS WITH WASHERS 2 SHOULDER BOLTS WITH RIGHT AND

More information

Page 1 of 12 GENERAL INSTRUCTIONS KHJKK Installation

Page 1 of 12 GENERAL INSTRUCTIONS KHJKK Installation Page 1 of 12 KHJKK PICTURE ABOVE IS THE UNIVERSAL KIT; YOUR KIT MAY BE DIFFERENT. THIS KIT INCLUDES: 8 M8-1.25X30MM BOLTS WITH WASHERS 8 M8-1.25X40MM BOLTS WITH WASHERS 2 PINS RIGHT AND LEFT HINGE ASSEMBLY

More information

Installation for Full Size Polaris Ranger Crew Doors

Installation for Full Size Polaris Ranger Crew Doors Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated

More information

PPM-5710 JK HEAVY DUTY SKID PLATE ASSEMBLY Version 2.0

PPM-5710 JK HEAVY DUTY SKID PLATE ASSEMBLY Version 2.0 SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-5710 JK HEAVY DUTY SKID PLATE ASSEMBLY Version 2.0 GENERAL NOTES: These instructions are also available on our website; www.synergymfg.com.

More information

ASSEMBLY INSTRUCTIONS FOR SERVICE BODY A MOUNT RACKS

ASSEMBLY INSTRUCTIONS FOR SERVICE BODY A MOUNT RACKS ASSEMBLY INSTRUCTIONS FOR SERVICE BODY A MOUNT RACKS T12 Service Body A shown with optional middle crossbar Package Contents: HARDWARE KIT PARTS (8) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLIES

More information

Models 2030 and 2040

Models 2030 and 2040 Models 2030 and 2040 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-8 Installation... 9 Operation... 9 Maintenance... 10 Accessories... 10 Limited Warranty... 10 Document # 101290 0607 Printed

More information

Install Instructions. NewAge Steel Welded Tall Locker

Install Instructions. NewAge Steel Welded Tall Locker Kit Contains Full Width Adjustable Steel Shelves (4) Height-Adjustable Steel Leveling Legs (4) Aluminum Door Trim (2) 2.5 x ¼ Cabinet Mounting Lag Bolts (4) Large Zinc Plated Mounting Washers (4) 5/8 x

More information

Installation Instructions - Model V4JSD 1

Installation Instructions - Model V4JSD 1 Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)

More information

Please read and understand the OnBoard Timpani Cart Owner s Manual before using the Timpani Cart.

Please read and understand the OnBoard Timpani Cart Owner s Manual before using the Timpani Cart. Assembly and Owner s Manual OnBoard Timpani Cart Performance Position Towing Position CONTENTS Important User Information...........................2 General......................................2 Manufacturer.................................2

More information

M ACS Instructions

M ACS Instructions APPLICABLE MODELS: Nissan Frontier 2005 and up short bed with Utili-Trak mounting rails PACKAGE CONTENTS 00-0060-M-01-1205 ACS Instructions Leitner Designs 25675 Taladro Circle Unit E Mission Viejo, CA

More information

2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions

2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions 2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2.

More information

Jeep. Flat Style Fender Flares Rear Pair. Included in Hardware Kit:

Jeep. Flat Style Fender Flares Rear Pair. Included in Hardware Kit: Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

INSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY

INSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY NEWAGE STEEL WELDED CABINETRY WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES ALL CABINETS MUST BE MOUNTED TO STUDS ON A SECURE WALL, AS PER THESE INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS

More information

Race Splitter Upgrade Kit Installation Instructions

Race Splitter Upgrade Kit Installation Instructions Race Splitter Upgrade Kit Installation Instructions Eric Hazen Rev. 1 Overview: Detailed instructions on installing the FT86 Speed Factory Race Splitter Upgrade Kit on a BRZ; FR-S grills are different

More information

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.

More information

Models 2130 and 2140

Models 2130 and 2140 Models 2130 and 2140 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-10 Installation...11 Operation... 11 Maintenance... 12 Accessories...12 Limited Warranty... 12 Printed in USA 2007 Perform

More information

JK Front Crusher Flares

JK Front Crusher Flares INSTALLATION INSTRUCTIONS INST-17-03-030_A JK Front Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.

More information

TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS

TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR 53-87 FORD FLARESIDE TRUCKS Vise Grip Clamps C-clamps Sharpie Marker Ball Peen Hammer Center Punch 3/8 or 1/2 Drill 5/32, 7/32, 9/32, and 3/8 Drill Bits

More information

PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT

PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT AEV30272AC Last Updated: 10/09/18 PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT Please visit www.aev-conversions.com to view the most current installation guide for this product. This is a new

More information

FORD INTERCEPTOR SEDAN READY BUCKLE

FORD INTERCEPTOR SEDAN READY BUCKLE INSTALLATION MANUAL FORD INTERCEPTOR SEDAN READY BUCKLE PART# FT3501RB We recommend you read through the installation guide prior to installation, if you have any questions please call us at 800-516-2322

More information

31082 INSTALLATION INSTRUCTIONS

31082 INSTALLATION INSTRUCTIONS 08 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 07-CURRENT MAKE: HONDA MODEL: RIDGELINE STYLE: TRUCK WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S

More information

INSTALLATION INSTRUCTIONS RH 412 STEEL DOORS

INSTALLATION INSTRUCTIONS RH 412 STEEL DOORS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job

More information

Installation Instructions HOSS Hardtop Organized Storage System

Installation Instructions HOSS Hardtop Organized Storage System Installation Instructions HOSS Hardtop Organized Storage System Application: Hard Top and Doors Storage System Part Number: 42801 www.bestop.com - We re here to help! Visit our web site and click on Ask

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut

More information

frame bracket Dodge x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab)

frame bracket Dodge x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab) , Rev 4 02/19 frame bracket 8552026 Dodge 3500 4 x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab) 14 5 7 2 4 11 9 10 17 3 6 1 8 13 15 16 18 12 ITEM PART # DESCRIPTION QTY. 1 00085.50 FLAT WASHER 10 2 00248

More information

Flat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit:

Flat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit: Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

INSTALLATION GUIDE NS Double Clamp Ladder Rack NV200 / City Express ( Aluminum )

INSTALLATION GUIDE NS Double Clamp Ladder Rack NV200 / City Express ( Aluminum ) INSTALLATION GUIDE 1530-NS Double Clamp Ladder Rack NV200 / City Express ( Aluminum ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Ladder Rack Assembly... 3-5 5-13 Phase 2 - Installation q

More information

INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X

INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X Thank you for purchasing Specialty s Convertible Top for your Jeep vehicle. It has been designed for great fit and long wear. Please

More information

Please Do Not Return This Product To The Store!

Please Do Not Return This Product To The Store! MODEL NOS. T81 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be shipped inside

More information

Spa & Hot Tub Necessities. Cover Removal System Installation & Use Manual

Spa & Hot Tub Necessities. Cover Removal System Installation & Use Manual Spa & Hot Tub Necessities Cover Removal System Installation & Use Manual SET-UP AND ASSEMBLY BEFORE BEGINNING ASSEMBLY, CAREFULLY READ THE FOLLOWING INFORMATION AND INSTRUCTIONS: Place all parts in a cleared

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

INSTALLATION INSTRUCTIONS Product No. MULTI-FIT PICK-UP

INSTALLATION INSTRUCTIONS Product No. MULTI-FIT PICK-UP INSTALLATION INSTRUCTIONS Product No. You can take it with you. PLYMOUTH, MICH. MULTI-FIT PICK-UP 37034 SMALL PARTS PACKAGE 37424 WARNING: DO NOT LUBRICATE THREADS, BOLT FAILURE MAY OCCUR DUE TO OVER TIGHTENING.

More information

VersaRail Gate Kit. freedomproduct.com. To register your product, please visit: INSTALLATION INSTRUCTIONS

VersaRail Gate Kit. freedomproduct.com. To register your product, please visit: INSTALLATION INSTRUCTIONS VersaRail Gate Kit INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Refer to manufacturers safety instructions when operating any tools. To register your product, please visit:

More information

Trailer Receiver Hitch Installation Instructions

Trailer Receiver Hitch Installation Instructions Model/Application: 1006: 10-15 R60 Countryman 10-15 R60 Countryman S 11-xx R61 Paceman 11-xx R61 Paceman S Hitch Capacity: 2000 lbs gross, 200 lb. max tongue Notes: This hitch allows for a removable ball

More information

Jeep Wrangler JK & 4-Door Front Pair Part # Revision H

Jeep Wrangler JK & 4-Door Front Pair Part # Revision H Jeep Wrangler JK 2007 2 & 4-Door Front Pair Part # 10045 Revision H 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with

More information

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM The only table saw fence with Automatic Positioning Control TM OWNER S MANUAL Please read this owner s manual before use and keep it at hand for reference. Note: The INCRA TS III system consists of three

More information

PARTITION INSTALLATION INSTRUCTIONS

PARTITION INSTALLATION INSTRUCTIONS PARTITION INSTALLATION INSTRUCTIONS 2015 Chevrolet Tahoe PPV / Part Number 5703FW, FWA & FEW Do not attempt to install this product on any vehicle equipped with third row seating! Parts List Distributed

More information

Driver/Left Top. Support Bracket

Driver/Left Top. Support Bracket PARTS LIST: 1 Grille Guard 8 10mm Lock Washers 1 Driver/Left Frame Bracket 8 10mm Hex Nuts 1 Passenger/Right Frame Bracket 2 8-1.25mm x 25mm Button Head Bolts 1 Driver/Left Bottom Support Bracket 2 8mm

More information

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT: 1963-1972 C10 Chevy Truck Custom IFS Installation Instructions Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE PARTS LIST BELOW

More information

======================================================================================== ( DR / DR) JK WRANGLER MOD RACK

======================================================================================== ( DR / DR) JK WRANGLER MOD RACK (10984 4DR / 10982 2DR) JK WRANGLER MOD RACK INSTALLATION SHEET Important Notes: Some brands of windshield light brackets and snorkels may not be compatible with the 10984 MOD Rack System. Body lifts are

More information

738 SERIES PIVOT SHOWER DOOR

738 SERIES PIVOT SHOWER DOOR INSTALLATION INSTRUCTIONS 738 SERIES PIVOT SHOWER DOOR Copyright Alumax Bath Enclosures 1997. All rights reserved. Page 1 of 8 LIMITED WARRANTY AND REMEDY Alumax Bath Enclosures warrants to its dealers,

More information

CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS

CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS 20017 04/22/03 REV-A CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS Tools Required for Installation: (A) 3/16 Drill Bit (B) Pop-Rivet Gun (C) Air

More information

Jeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit:

Jeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit: Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Sea Doo Spark Engine Access Kit

Sea Doo Spark Engine Access Kit Sea Doo Spark Engine Access Kit PART# - RS4-130-EAK APPLICATION(S): Sea Doo Spark. 2up & 3up Models. We strongly recommend the use of a service manual to familiarize yourself with the various components

More information

INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger

INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.

More information

Installation Instructions TrekStep Side Mount

Installation Instructions TrekStep Side Mount Installation Instructions TrekStep Side Mount Vehicle Application Chevrolet Silverado / GMC Sierra All Bed Sizes 1999 Current Part Number: 75400-15 www.bestop.com - We re here to help! Visit our web site

More information

Installation Instructions Kit, Base Rail Bracket Part # 31413

Installation Instructions Kit, Base Rail Bracket Part # 31413 Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating and

More information

FENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description TOOLS REQUIRED

FENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description TOOLS REQUIRED ` FENDER FLARE Part No: FFD3001S TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE FENDER FLARE CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required

More information

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER. SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information

ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline)

ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) NOTE TO INSTALLER: IMPORTANT READ BEFORE ATTEMPTING INSTALLATION. Allow extra time, up to 2 hours to install this cover. Disassembly

More information

ASSEMBLY INSTRUCTIONS FOR HAULER II UNIVERSAL CAMPER SERIES RACKS

ASSEMBLY INSTRUCTIONS FOR HAULER II UNIVERSAL CAMPER SERIES RACKS ASSEMBLY INSTRUCTIONS FOR HAULER II UNIVERSAL CAMPER SERIES RACKS C11U2873-1 shown above Package Contents: HARDWARE KIT PARTS (4) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLY (20) 3/8-16 x

More information

PLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING

PLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING SleepSafe Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of safe use. Carefully unpack all the contents of your bed and verify that all parts are included

More information

PLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING

PLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of safe use. Carefully unpack all the contents of your bed and verify that all parts are included using

More information

For additional assistance call

For additional assistance call The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or

More information

YJ DeFenders. These installation instructions apply to the following Poison Spyder products:

YJ DeFenders. These installation instructions apply to the following Poison Spyder products: INSTALLATION INSTRUCTIONS INST-13-02-070_A YJ DeFenders IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation. If

More information

Toyota Pocket Style Fender Flares Set of 4

Toyota Pocket Style Fender Flares Set of 4 Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SNYPER TUBULAR FENDERS APPLICATION: 2007-2017 Jeep Wrangler JK PART NUMBER: 62-1005, 62-1015 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 FRONT FENDERS, DRIVER (1) AND PASSENGER

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. O p. 1 of 16 INSTALLATION & OWNER S MANUAL V4213 BALL CAGE KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation

More information

1PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Holden VE Ute 2007

1PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Holden VE Ute 2007 PC TONNEAU COVER INSTALLATION INSTRUCTIONS Holden VE Ute 007 Part Number: EGR-PVE-UNP Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents.

More information

00108/00110 INSTRUCTION MANUAL

00108/00110 INSTRUCTION MANUAL 00108/00110 INSTRUCTION MANUAL Removable and Adjustable Mudflap System IMPORTANT! Please Read this Instruction Booklet prior to assembly of your Rock Tamer Kit. IMPORTANT! Exhaust Systems Note: Any modifications

More information

Katerack Wagon Shelving System

Katerack Wagon Shelving System Ford Transit Connect Assembly Installation Instructions Sheet 1 of 14 BEFORE YOU START! IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED IN THE SPECIFIED ORDER

More information

Ford Cut-Out Fender Flares Front Pair

Ford Cut-Out Fender Flares Front Pair Ford Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET

More information