Surface Roughness Measuring Instruments Surftest Page 523. Contour Measuring Instruments Contracer Page 540

Transcription

1 Form Measurement Surface Roughness Measuring Instruments Surftest Page 523 Contour Measuring Instruments Contracer Page 540 Surface Roughness and Contour Measuring Instruments Formtracer Page 547 Accessories Surftest, Contracer, Formtracer Page 555 Form Measuring Instruments Roundtest Page

2 Surftest SJ-210 Specifications Drive unit Measuring range Traverse Measuring speed 16 4,8 [S-type] 17,5 5,6 [S-type] 0,25 /s ; 0,5 /s; 0,75 /s Detector Measuring method Differential inductance Range 360 µm Stylus Diamond Tip Skid radius 40 Display unit Profiles Roughness standards Digital filter Cut-off length Tolerance Roughness Profile (R), R-Motif, DF-Profile and more EN ISO, VDA, JIS, ANSI and customize settings Gauss, 2CR75, PC75 λc : 0,08 ; 0,25 ; 0,8 ; 2,5 λs : 2,5 µm; 8 µm Colored upper / lower limit Series Portable Surface Roughness Measuring Instrument This is a portable measuring instrument that allows you to easily and accurately measure surface roughness. The Surftest SJ-210 offers you the following benefits: It works independently of mains power, allowing you to make on-site measurements. The 6.0 cm [2.4 ] colour graphic, back-lit LCD gives you excellent readability. It complies with many standards including EN ISO, VDA, ANSI, JIS as well as customised settings. Different drivers expanding the range of applications. Calculation results, assessed profiles, bearing and amplitude curves can be displayed. Support of 16 languages. Operation by keys on the front and under the sliding cover. Interface Power supply Mass USB, Digimatic, RS-232C, Foot switch AC adapter or rechargeable battery 500g SJ-210 Metric Detector measuring force Stylus Tip radius Stylus Tip angle [mn] [µm] Description D 0, SJ-210 model D 0, SJ-210R model D 0, SJ-210S model Software USB COMMUNICATION TOOL as a free download on (refer to page Optional Software USB Counication Tool) Standard R-type S-type Refer to Surftest SJ-210 brochure 523

3 Surftest SJ-210 Series Portable Surface Roughness Measuring Instrument The SJ-210R Retract System is a portable measuring instrument for surface roughness that includes a safety system. The detector starts in a safety position, not in contact with the workpiece surface. When measurement starts, the detector is lowered onto the workpiece while the drive unit moves in X measuring direction. During the return movement, the detector lifts up from the workpiece surface before returning to the start position. This is useful for avoiding stylus damage in applications where you cannot easily see the test surface. SJ-210S (detailed information further on in this chapter) The SJ-210S model is a portable measuring instrument for surface roughness that has a transverse drive capability. This allows you to test shrouded surfaces in the transverse direction, such as crankshaft bearing surfaces, flanged features or deep grooves. Additional Specifications Other accessories Optional accessories Other optional and standard accessories are listed later in this section Description Price Granite stand (12AAA221 is needed for SJ-210/310) Measuring device for 2, cylindrical workpieces Measuring device as 2, universal fixture Measuring device for 2, measuring in pipes 12AAA221 Adapter for magnetic stand Standard drive unit 17, R-Type drive unit 17,5 1, S-Type drive unit 5,6 2, BAK699 Carrying case Digimatic cable (1 m) Digimatic cable (2 m) AZD790D Connecting cable U-Wave ADV380D USB Input Tool Direct cable (2 m) 12BAA303 Connecting cable for extension 1 m SJ ,1 174, ,1 160 Keyboard protective cover open POWER START DATA STOP 65,8 PAGE 52,1 Back view Dimensions (displayed with SJ-210) 524

4 Surftest SJ-310 Specifications Drive unit Measuring range Traverse Measuring speed 16 4,8 [S-type] 17,5 5,6 [S-type] 0,25 /s; 0,5 /s; 0,75 /s Detector Measuring Differential inductance method Range 360 µm Stylus Diamond Tip Skid radius 40 Display unit Profiles Roughness standards Digital filter Cut-off length Printer Tolerance Roughness Profile (R), R-Motif, DF-Profile and more EN ISO, VDA, JIS, ANSI and customize settings Gauss, 2CR75, PC75 λc : 0,08 ; 0,25 ; 0,8 ; 2,5 ; 8 λs : 2,5 µm; 8 µm Thermal Printer Colored upper / lower limit Series Portable Surface Roughness Measuring Instrument This is a portable measuring instrument that allows you to easily and accurately measure surface roughness. The Surftest SJ-310 offers you the following benefits: Skid system with touch-screen functionality and built-in printer. It works independently of mains power, allowing you to make on-site measurements. Easy and intuitive menu navigation. The large 14.5cm [5.7 ] colour LCD gives you high visibility. It complies with many standards including EN ISO, VDA, ANSI, JIS as well as customised settings. You can store up to 10 different measuring conditions inside the SJ-310, and up to 500 with an optional SD card. Statistical analysis and coloured tolerance judgement. 2 different evaluation conditions within 1 measurement adjustable. You can separately password protect many functions. It comes with support for 16 languages. Interface Power supply USB, Digimatic, RS-232C, Foot switch AC adapter or rechargeable battery SJ-310 Metric Detector measuring force Stylus Tip radius Stylus Tip angle [mn] [µm] Description D 0, SJ-310 model D 0, SJ-310R model D 0, SJ-310S model Software USB COMMUNICATION TOOL as a free download on (refer to page Optional Software USB Counication Tool) Standard R-type S-type Refer to Surftest SJ-310 brochure 525

5 Surftest SJ-210 and SJ S-Type Series 178 Portable Transverse Measurement with S-Type Drive Unit This is an S-Type drive unit for the Surftest SJ-210 and SJ-310 that provides portable transverse measurement. It offers you the following benefits: It is compatible with the conventional drive units of the Surftest SJ-210 and SJ-310. You can simply connected it to the display unit. A typical application would be to position the S-Type unit on a crankshaft journal bearing, as shown in the photograph below. Once started the S-Type drive will track the stylus across the surface transversely to its own axis and reliably measure surface roughness in the direction of the crankshaft axis. Transverse tracking simplifies the measurement of surface roughness even in very confined situations, which has long been a problem with conventional instruments which allow only longitudinal measurement. Specifications Traverse Measuring speed Optional accessories 5,6 0,25 /s; 0,5 /s; 0,75 Description Pri Granite stand 71 (12AAA221 is needed for SJ-210/310) 12AAA221 Adapter for magnetic stand Standard drive unit 17, R-Type drive unit 17,5 1, S-Type drive unit 5,6 2,31 S - Type Drive Unit Set: [ incl AAE644-12AAE643 ] Traverse Detector measuring force Stylus Tip radius Price Stylus Tip angle [mn] [µm] [ ] ,6 0, , Linear movement of S-Type 12AAE644 V-type adapter 12AAE643 Point - contact adapter 526

6 Accessories for SJ-210 and SJ-310 Series Standard and Optional Accessories for Surftest SJ-210 / SJ-310 Model Surftest SJ-210 Surftest SJ-210R Surftest SJ-210S Surftest SJ-310 Surftest SJ-310R Surftest SJ-310S Price Description Std Opt Std Opt Std Opt Std Opt Std Opt Std Opt 12AAA Extension rod length 50 12AAA Height adjustment feet 12AAA Nosepiece (flat) 12AAA Nosepiece (cylindrical) 12AAA Adapter for vertical position 12AAA Adapter for magnetic stand 12AAA Height gauge adapter 12AAD USB cable for SJ-310 / SJ AAE Point - contact adapter 12AAE V-type adapter 12AAJ Footswitch 12AAL Protective sheets for display 12AAL RS-232C cable for printer 12AAL068D USB cable for SJ AAL Memory card 12AAN040 Protective film 12AAN Battery 12BAA Connecting cable for extension 1 m 12BAG Touch pen 12BAK Calibration table 12BAK AC adapter 12BAL402 Touch Panel Protection AC Adapter Granite stand Standard Drive unit 17, , S-Type drive unit 5, , R-Type drive unit 17, Standard detector 2 µm; 0,75 mn Detector for small holes Ø4,5 ; 2 µm; 0,75 mn Detector for small holes Deep groove detector 2 µm; 0,75 mn Detector for S-drive 5 µm; 4 mn Detector for S-drive 2 µm; 0,75 mn , Detector for gear tooth surface 2 µm; 0,75 mn Detector 5 µm; 4 mn Detector for soft materials 10 µm; 4 mn Detector for small holes Ø4,5 ; 5 µm; 4 mn Detector for small holes Ø2,8 ; 5 µm; 4 mn Deep groove detector 5 µm; 4 mn , Detector for gear tooth surface 5 µm; 4 mn; DDS Printerset for SJ Roughness specimen Ra 3 µm Roughness specimen Ra 0,5 µm /3 µm Roughness specimen Ra 1 µm Printer papers (5 rolls) 527

7 6 9 Accessories for SJ-210 and SJ-310 Series AAA210 12BAA303 12AAA219 12AAA222 Optional accessories Description Price Measuring device for 2, cylindrical workpieces Measuring device as 2, universal fixture Measuring device for measuring in pipes 2, AAA218 12AAA217 12AAA216 12AAA221 (ø 8 ) R / ø / ø (displayed with 12AAA221 + SJ-210) ø / ø / / Stylus ø ø / AAA AAA221 12AAA AAA216 12AAA217 12AAA

8 Surftest SJ-410 Specifications Drive unit Traverse Measuring speed SJ-411: 25 SJ-412: 50 0,05 /s; 0,1 /s; 0,2 /s; 0,5 /s; 1,0 /s Detector Measuring Skidless - Differential inductance method Range 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) Positioning ±1,5 (tilting), 10 (up/down) Display unit Profiles Standards Analysis graphs Digital filter Cut-off length Printer Tolerance Primary Profile (P), Roughness Profile (R), Waviness (W), MOTIF (R, W) and more EN ISO, VDA, JIS, ANSI and customize settings BAC, ADC Gauss, 2CR75, PC75 λc : 0,08 ; 0,25 ; 0,8 ; 2,5 ; 8 λs : 2,5 µm; 8 µm; 25 µm Thermal Printer Colored upper / lower limit Series Portable Surface Roughness Measuring Instrument This is a portable measuring instrument that allows you to easily and accurately measure surface roughness. The Surftest SJ-410 offers you the following benefits: Skidless system with touch-screen functionality and built-in printer. It works independently of mains power, allowing you to make on-site measurements. Easy and intuitive menu navigation. The large 14.5cm [5.7 ] colour LCD gives you high visibility. The skidless detector allows you to measure the primary profile (P), roughness profile (R), waviness profile (W) and more. Surface compensation of curved, radial and tilted surfaces. It complies with many standards including EN ISO, VDA, ANSI, JIS as well as customised settings. You can store up to 10 different measuring conditions inside the SJ-410, and up to 500 with an optional SD card. It allows two different evaluation conditions within one measurement adjustable. You can separately password protect many functions. It comes with support for 16 languages. Available options include an auto-set unit, X-axis fine adjustment and digital levelling unit. Interface Power supply USB, Digimatic, RS-232C, Foot switch AC adapter or rechargeable battery SJ-410 Software USB COMMUNICATION TOOL as a free download on (refer to page Optional Software USB Counication Tool) Refer to Surftest SJ-410 brochure Surftest SJ-411 Traverse : 25 Traverse straightness : 0,3 µm / 25 Detector measuring force [mn] Stylus Tip angle Stylus Tip radius [µm] D 0, D D 0, Surftest SJ-412 Traverse : 50 Traverse straightness : 0,5 µm / 50 Detector measuring force [mn] Stylus Tip angle Stylus Tip radius [µm] D 0, D

9 Surftest SJ-410 Series Portable Surface Roughness Measuring Instrument Additional Specifications Optional accessories Other optional and standard accessories are listed later in different sections for accessories and styli. Deep groove measurement R-surface measurement Optional: Autoset unit X-axis adjustment Tilting adjustment unit Upside down measurement SJ-411: 207,5 / SJ-412: 234 Drive unit Scope of delivery Optional accessories Description Price Detector 0,75 mn Detector 4 mn Three-axis adjustment table 4, Leveling table D.A.T. 2, Digimatic XY leveling table 3, x XY leveling table 2, x Roughness specimen Ra = 1 µm Step gauge (1, 2, 5, 10) µm Reference step specimen (2, 10) µm Precision vice AAB358 Cylinder attachment ø Digimatic cable (1 m) Digimatic cable (2 m) AZD790D Connecting cable U-Wave AAD510 USB cable for SJ-310 / SJ AAL069 Memory card AAG202 Extension rod AAG203 Extension rod Stands Granite stand Consumable spares Description Price 12AAB355 Nosepiece BAG834 Touch pen BAL402 Touch Panel Protection 12AAN046 Battery Printer paper (5 rolls) Leveling table D.A.T. 12AAB358 Cylinder attachment (displayed with SJ-411) 530

10 Surftest SJ-500 Specifications Drive unit Traverse Measuring speed Drive speed Traverse straightness 50 0,02-5 /s 0-20 /s or joystick operation 0,2 µm / 50 Detector Measuring Skidless - Differential inductance method Range 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) Positioning ±1.5 (tilting) 30 (up/down) Display unit Profiles Standards Analysis graphs Digital filter Cut-off length Printer Optional accessories Primary Profile (P), Roughness Profile (R), Waviness (W), MOTIF (R, W) and more EN ISO, VDA, JIS, ANSI and customize setting BAC, ADC Gauss, 2CR75, PC75, RobustSpline λc : 0,025 ; 0,08 ; 0,25 ; 0,8 ; 2,5 ; 8 ; 25 λs : 0,25 µm; 0,8 µm; 2,5 µm; 8 µm; 25 µm; 80µm; 250µm; None λf : 0,08; 0,25; 0,8; 2,5; 8; 25; None Thermal printer Description Price Detector 0,75 mn Detector 4 mn Granite stand 3, x450x Granite stand 1, x250x Three-axis adjustment table 4, Leveling table D.A.T. 2, Digimatic XY leveling table 3, x XY leveling table 2, x 25 12AAG202 Extension rod AAG203 Extension rod Series Surface Roughness Measuring Instrument This is a portable measuring instrument that allows you to easily and accurately measure surface roughness. The Surftest SJ-500 offers you the following benefits: The skidless detector allows you to measure the primary profile (P), roughness profile (R), waviness profile (W) and more. User friendly control unit for high precision surface roughness measurement. The large 19cm [7.5 ] colour TFT LCD with touch-screen functionality gives you high visibility and ease of use. The display menu is easy to read and simple to operate. It complies with many standards including EN ISO, VDA, ANSI, JIS as well as customised settings. The built-in joystick on the control unit enables quick and easy positioning. The manual adjustment knob allows you to finely position a small stylus to measure the inside surface of small holes. The detector unit allows a 90 displacement of the stylus, which is ideal for crankshaft and narrow space measurement. You can use the instrument stand-alone or mounted on a stand. SJ-500 Detector measuring force Stylus Tip radius Stylus Tip angle [mn] [µm] D 0, D SJ-500 with optional manual column stand Preview Software USB COMMUNICATION TOOL as a free download on (refer to page Optional Software USB Counication Tool) Refer to SURFACE MEASUREMENT brochure x450x x250x578

11 Surftest SV-2100 Series Surface Roughness Measuring Instrument This is a stationary measuring instrument that allows you to easily and accurately measure surface roughness. The Surftest SV-2100 offers you the following benefits: It is mounted on a granite base with a manual or power column. The large 19cm [7.5 ] colour TFT LCD gives you high visibility and touch-screen functionality. It has a user friendly display unit for high precision surface roughness measurement. It complies with many standards including EN ISO, VDA, ANSI, JIS as well as customised settings. Designed for usage in workshop areas. Specifications Drive unit Traverse Measuring speed Drive speed Traverse straightness 100 0,02-5 /s X = 0-40 /s Z2 = 0-20 /s or joystick operation 0,15 µm / 100 Detector Measuring Skidless - Differential inductance method Range 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) SV-2100S4 SV-2100H4 model Vertical travel : 550 power column Granite base size (WxD) : 600 x 450 Detector measuring force [mn] Stylus Tip angle Stylus Tip radius [µm] D 0, D SV-2100M4 model Vertical travel : 350 manual column Granite base size (WxD) : 600 x 450 Detector measuring force [mn] Stylus Tip angle Stylus Tip radius [µm] D 0, D SV-2100M4 Display unit Profiles Standards Analysis graphs Digital filter Cut-off length Printer Optional accessories Primary Profile (P), Roughness Profile (R), Waviness (W), MOTIF (P, R, W) and more EN ISO, VDA, JIS, ANSI and customize settings BAC, ADC Gauss, 2CR75, PC75, RobustSpline λc : 0,025 ; 0,08 ; 0,25 ; 0,8 ; 2,5 ; 8 ; 25 ; 80 λs : 0,25 µm; 0,8 µm; 2,5 µm; 8 µm; 25 µm; 80 µm; 250 µm; none λf : 0,08 ; 0,25 ; 0,8 ; 2,5 ; 8 ; 25 ; 80 ; none Thermal printer Description Price 12AAG202 Extension rod AAG203 Extension rod Cross-travel table 2, XY range : 100x Rotary vice (heavy-duty type) 1, SV-2100S4 model Vertical travel : 350 power column Granite base size (WxD) : 600 x 450 Detector measuring force [mn] Stylus Tip angle Stylus Tip radius [µm] D 0, D Preview SV-2100W4 model Vertical travel : 550 power column Granite base size (WxD) : 1000 x 450 Detector measuring force [mn] Stylus Tip angle Stylus Tip radius [µm] D 0, D Software USB COMMUNICATION TOOL as a free download on (refer to page Optional Software USB Counication Tool) Refer to SURFACE MEASUREMENT brochure 532

12 Surftest SJ-500P - SV-2100P Specifications Drive unit Traverse Measuring speed Drive speed Traverse straightness 50 0,02-5 /s 0-20 /s 0,2 µm / 50 Detector Measuring Skidless - Differential inductance method Range 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) Positioning ±1,5 (tilting) 30 (up/down) Series Surface Roughness Measuring Instruments with Software FORMTRACEPAK These are surface roughness measuring instruments with software FORMTRACEPAK. Software FORMTRACEPAK offers you the following benefits: It supports all standard conform analyses including EN ISO, VDA, ANSI, JIS as well as customised settings. It can be used for contour calculation within the measuring range. It offers total support for measurement system control, analysis and inspection report. All advantages of the SJ-500 and SV-2100 also apply to the P Type. Software FORMTRACEPAK Measurement conditions SJ-500P Detector measuring force Stylus Tip radius Stylus Tip angle [mn] [µm] D 0, D Specifications Drive unit Traverse Measuring speed Drive speed Traverse straightness Formtracepak layout 100 0,02-5 /s X = 0-40 /s Z2 = 0-20 /s 0,15 µm / 100 Surftest SV-2100M4P Detector Measuring Skidless - Differential inductance method Range 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) Software FORMTRACEPAK Refer to the SURFACE MEASUREMENT brochure SV-2100P Detector measuring force Stylus Tip radius Stylus Tip angle [mn] [µm] D 0, D

13 Surftest SV-3100 Series Surface Roughness Measuring Instrument This is a stationary surface roughness measuring instrument with software FORMTRACEPAK that allows you to take highly accurate measurements. The Surftest SV-3100 offers you the following benefits: It complies with many standards including EN ISO, VDA, ANSI, JIS as well as customised settings. It also supports contour calculation within the measuring range of the styli software. Part programing as well as motorised axes give you many features of a CNC instrument. The X-axis uses a superbly anti-abrasive ceramic drive unit guideway, so you don t need any lubrication. You can choose from a huge number of styli that are easy to replace. It has an easy-to-operate remote box with many functionalities. Specifications Traverse 100 / 200 Range 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) Drive speed X = 0-80 /s Z2 = 0-20 /s Measuring 0,02-5 /s speed Inclining ±45 range Profiles Primary Profile (P), Roughness Profile (R), Waviness (W), MOTIF (P, R, W) and more Standards EN ISO, VDA, JIS, ANSI and customize setting Software FORMTRACEPAK Enables control of all axes and rotary table for realizing efficient measurement automation. You can also perform contour evaluation that allows free analysis of level differences, angles, pitch, area and other characteristics as well as surface roughness evaluation. In addition, you can create an original inspection certificate by setting the print format to suit your particular requirements. SV-3100 X-axis measuring range : 100 X-axis Traverse straightness : (0.05+1L/100) µm, L = Measurement length () Model SV-3100S4 SV-3100S4. SV-3100H4 SV-3100H4. SV-3100W4 SV-3100W D D D D D D-2 Detector measuring force [mn] 0,75 4 0,75 4 0,75 4 Stylus Tip angle Stylus Tip radius [µm] Vertical travel Granite base size (WxD) 600x x x x x x450 X-axis measuring range : 200 X-axis Traverse straightness : 0.5 µm/200 Model SV-3100S8 SV-3100S8. SV-3100H8 SV-3100H8. SV-3100W8 SV-3100W D D D D D D-2 Detector measuring force [mn] 0,75 4 0,75 4 0,75 4 Stylus Tip angle Stylus Tip radius [µm] Vertical travel Granite base size (WxD) 600 x x x x x x 450 Optional Y-axis Optional Rotary Table θ1-12aad975 Optional Rotary Table θ Refer to SURFACE MEASUREMENT brochure 534

14 Surftest SV-3100 Additional Specifications Optional accessories Other optional and standard accessories are listed later in different sections for accessories and styli. Series Surface Roughness Measuring Instrument Dimensions and Optional accessories Optional accessories Description Price Y-axis table 12AAD975 θ1-axis table θ2-axis table Manual vibration isolator 3, Stand for vibration isolator Dynamic vibration isolator Cross-travel table 2, XY range : 100x Rotary vice (heavy-duty type) 1, AAG202 Extension rod AAG203 Extension rod Reference step specimen (2, 10) µm Automatic leveling table SV-, CV-series, CS [1176] [500] [640] [1000] 156 SV-3100S4 - SV-3100H4 - SV3100W ( ) SV-3100H4 [ ] SV-3100W [590] [500] [1176] FORMTRACEPAK [1000] SV-3100S8 - SV-3100H8 - SV-3100W8 ( ) SV-3100H8 [ ] SV-3100W8 535

15 Surftest Extreme SV-3000CNC Series 178 CNC Surface Roughness Measuring Instrument These is a fully CNC surface roughness measuring instrument with powerful software FORMTRACEPAK. The Surftest Extreme SV-3000CNC offers you the following benefits: It is perfectly made for increased throughput of multiple profile and workpiece measurement tasks. Each axis has a drive speed of up to 200 /s. You can take continuous measurement over horizontal and inclined surfaces by power-tilting the drive unit. Within the measuring range of the styli software FORMTRACEPAK supports contour calculation 3D topography measurement as option available Inclined plane measurement is possible through 2-axis simultaneous control in the X and Y directions. The detector unit incorporates an anti-collision safety device, causing it to automatically stop if its main body collides with a workpiece or jig. Specifications Traverse X = 200 Y = 200 Range 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) Measuring 0,02-2 /s speed Drive speed CNC mode: max. 200 /s Joystick mode: 0-60 /s Traverse 0,5 µm / 200 straightness Inclining +45 (CCW) to -10 (CW) range Profiles Primary Profile (P), Roughness Profile (R), Waviness (W), MOTIF (P, R, W) and more Standards EN ISO, VDA, JIS, ANSI and customize setting Software FORMTRACEPAK-6000 Allows control of all axis, optional motor-driven Y-axis table and rotary table for efficient automated measurement. Surface roughness analyisis and contour evaluation can be performed using analysis of level differences, angle, pitch, area and contour tolerancing as standard. An inspection certificate can be created by setting the print format as required. Additional Specifications Optional accessories Optional accessories Other optional and standard accessories are listed later in different sections for accessories and styli. Description 12AAD975 θ1-axis table θ2-axis table Automatic leveling table CNC D leveling table 12AAE032 Vibration isolator stand 12AAE449 Cabin for H-type SV-3000CNC Model SV-3000CNC-S SV-3000CNC-H SV-3000CNC-S. SV-3000CNC-H Z2-axis vertical travel Y-axis table unit - - Installed Installed α-axis unit Installed Installed Installed Installed Measuring force 0,75 mn ( ) 4 mn ( ) 0,75 mn ( ) 4 mn ( ) 0,75 mn ( ) 4 mn ( ) 0,75 mn ( ) 4 mn ( ) Refer to SURFACE MEASUREMENT brochure Automatic measurement 536

16 Surftest Extreme SV-M3000CNC Specifications Traverse X = 200 Y = 800 Z2 = 500 Range 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) Measuring 0,02-2 /s speed Drive speed CNC mode: max. 200 /s Joystick mode: 0-50 /s Traverse straightness Inclining range Profiles Standards Loading weight X = 0,5 µm / 200 (standard) X = 0,7 µm / 200 (long-type detector) X = 0,5 µm / 200 (rotary-type detector) Y = 0,5 µm / 50 ; 2 µm / 800 (standard) Y = 0,7 µm / 50 ; 3 µm / 800 (long-type detector) Y = 0,7 µm / 50 ; 3 µm / 800 (rotary-type detector) -45 (CCW) to +10 (CW) Primary Profile (P), Roughness Profile (R), Waviness (W), MOTIF (P, R, W) and more EN ISO, VDA, JIS, ANSI and customize setting 300 kg Series CNC Surface Roughness Measuring Instrument This is a top performance CNC surface roughness measuring instrument with powerful software FORMTRACEPAK. The Surftest Extreme SV-M3000CNC offers you the following benefits: You can measure large and heavy workpieces such as engine blocks and crankshafts. It has an 800 moving column configuration to largely eliminate workpiece size restrictions. Each axis has a drive speed of up to 200 /s. When combined with the optional detector swivelling unit, continuous measurement over the bottom, top and side surface of a workpiece is possible. The huge load table has a self-contained structure ensuring that you can easily accoodate various size workpieces, standard and custom jigs, and auto-feed devices. Software FORMTRACEPAK Enables control of all axes for realizing efficient measurement automation. You can also perform contour evaluation that allows free analysis of level differences, angles, pitch, area and other characteristics as well as surface roughness evaluation. In addition, you can create an original inspection certificate by setting the print format to suit your particular requirements. Additional Specifications Optional accessories Other optional and standard accessories are listed later in different sections for accessories and styli. Refer to SURFACE MEASUREMENT brochure Detector hold type (Essential option) Standard Long type Rotary type Model Typical measurement task 537

17 ISO 1302: 2002 Notation method of surface texture ISO 4287: 1997 Geometrical Product Specifications (GPS) Surface Texture: Profile method Terms, definitions, and surface texture parameters ISO 4288: 1996 Geometrical Product Specifications (GPS) Surface Texture: Profile method Rules and procedures for the assessment of surface texture ISO 3274: 1996 Geometrical Product Specifications (GPS) Surface Texture: Profile method Nominal characteristics of contact (stylus) instruments Nominal Characteristics of Contact (Stylus) Instruments Workpiece surface Measurement loop Probe Stylus tip Reference guide skid Measurement profile Reference line Transducer Z-axis Signal Transfer Unit Amplifier AD converter Input/Output Appearance Quantized measurement profile Nominal texture suppression Profile filter ISO 3274: 1996 Input/Output Primary profile Parameter evaluation Definition of Parameters Amplitude Parameters (peak and valley) Maximum peak height of the primary profile Pp Maximum peak height of the roughness profile Rp Maximum peak height of the waviness profile Wp Largest profile peak height Zp within a sampling length ISO 4287 : 1997 Rp Feed device Drive Unit Stylus Shape A typical shape for a stylus end is conical with a spherical tip. Tip radius: rtip = 2 µm, 5 µm or 10 µm Taper angle of cone: 60, 90 In typical surface roughness testers, the taper angle of the stylus end is 60 unless otherwise specified R2µm R2µm Static Measuring Force Nominal radius of curvature of stylus tip: µm (4.0) Note Note 1: The maximum value of static measuring force at the average position of a stylus is to be 4.0mN for a special structured probe including a replaceable stylus. Metrological Characterization of Phase Correct Filters A profile filter is a phase-correct filter without phase delay (cause of profile distortion dependent on wavelength). The weight function of a phase-correct filter shows a normal (Gaussian) distribution in which the amplitude transmission is 50% at the cutoff wavelength. Data Processing Flow Surface profile on the real surface Measured profile Quantized profile Measurement AD conversion R5µm R5µm Static measuring force at the mean position of stylus: mn R10µm R10µm Tolerance on static measuring force variations: mn/µm Definition: Profile that results from the intersection of the real surface and a plane rectangular to it. Definition: Locus of the center of the stylus tip that traces the workpiece surface. Definition: Data obtained by quantizing the measured profile. ISO 11562: 1996 Suppresses irrelevant geometry of the surface such as inclination of a flat feature and curvature of a cylindrical feature using the least squares method. Low-pass filter of cutoff value λs λc Workpiece Fixture λs µm Probe (pickup) Stylus λc/λs Feed device Measuring loop Surface Profiles Column Relationship between Cutoff Value and Stylus Tip Radius The following table lists the relationship between the roughness profile cutoff value λc, stylus tip radius rtip, and cutoff ratio λc/λs Maximum rtip µm 2 2 Note 1 2 Note 2 5 Note 2 10 Base Measuring point distance µm Note 1: For a surface with Ra>0.5µm or Rz>3µm, a significant error will not usually occur in a measurement even if rtip= 5µm. Note 2: If a cutoff value λs is 2.5µm or 8µm, attenuation of the signal due to the mechanical filtering effect of a stylus with the recoended tip radius appears outside the roughness profile pass band. Therefore, a small error in stylus tip radius or shape does not affect parameter values calculated from measurements. If a specific cutoff ratio is required, the ratio must be defined. Amplitude transmission % Roughness profile Waviness profile λs λc λf Wavelength ISO 4287: 1997 Primary Profile Profile obtained from the measured profile by applying a low-pass filter with cutoff value λs. Roughness Profile Profile obtained from the primary profile by suppressing the longer wavelength components using a high-pass filter of cutoff value λc. Sampling length Maximum valley depth of the primary profile Pv Maximum valley depth of the roughness profile Rv Maximum valley depth of the waviness profile Wv Largest profile valley depth Zv within a sampling length Rv Sampling length Maximum height of the primary profile Pz Maximum height of the roughness profile Rz Maximum height of the waviness profile Wz Sum of height of the largest profile peak height Zp and the largest profile valley depth Zv within a sampling length Rz Rv Sampling length In Old JIS and ISO : 1984, Rz was used to indicate the ten point height of irregularities. Care must be taken because differences between results obtained according to the existing and old standards are not always negligibly small. (Be sure to check whether the drawing instructions conform to existing or old standards.) Mean height of the primary profile elements Pc Mean height of the roughness profile elements Rc Mean height of the waviness profile elements Wc Mean value of the profile element heights Zt within a sampling length m 1 Pc, Rc, Wc = Σ Zt i Zt1 Zt2 Zt3 m Zt4 i=1 Sampling length Zt5 Rp Zt6 Primary profile High-pass filter of cutoff value λc Primary profile parameters Band-pass filter that passes wavelengths between cutoff values λc and λf Waviness Profile Profile obtained by applying a band-pass filter to the primary profile to remove the longer wavelengths above λf and the shorter wavelengths below λc. Total height of the primary profile Pt Total height of the roughness profile Rt Total height of the waviness profile Wt Sum of the height of the largest profile peak height Zp and the largest profile valley depth Zv within the evaluation length Roughness profile Waviness profile Rz Rz i Quick Guide to Precision Measuring Instruments Surftest (Surface Roughness Testers) Rt Primary profile Rz Roughness profile parameters Waviness profile parameters Sampling length Evaluation length 538

18 Amplitude Parameters (average of ordinates) Arithmetical mean deviation of the primary profile Pa Arithmetical mean deviation of the roughness profile Ra Arithmetical mean deviation of the waviness profile Wa Arithmetic mean of the absolute ordinate values Z(x) within a sampling length 1 Pa, Ra, Wa = Z(x) dx l 1 PSm, RSm, WSm = m l 0 with l as lp, lr, or lw according to the case. Root mean square deviation of the primary profile Pq Root mean square deviation of the roughness profile Rq Root mean square deviation of the waviness profile Wq Root mean square value of the ordinate values Z(x) within a sampling length with l as lp, lr, or lw according to the case. Skewness of the primary profile Psk Skewness of the roughness profile Rsk Skewness of the waviness profile Wsk Quotient of the mean cube value of the ordinate values Z(x) and the cube of Pq, Rq, or Wq respectively, within a sampling length The above equation defines Rsk. Psk and Wsk are defined in a similar manner. Psk, Rsk, and Wsk are measures of the asyetry of the probability density function of the ordinate values. Kurtosis of the primary profile Pku Kurtosis of the roughness profile Rku Kurtosis of the waviness profile Wku Quotient of the mean quartic value of the ordinate values Z(x) and the fourth power of Pq, Rq, or Wq respectively, within a sampling length The above equation defines Rku. Pku and Wku are defined in a similar manner. Pku, Rku, and Wku are measures of the sharpness of the probability density function of the ordinate values. Spacing Parameters Mean width of the primary profile elements PSm Mean width of the roughness profile elements RSm Mean width of the waviness profile elements WSm Mean value of the profile element widths Xs within a sampling length Pq, Rq, Wq = 1 1 Rsk = Rq 3 lr 1 1 Rku = Rq 4 lr 1 Z 2 (x)dx l lr 0 lr 0 Xs1 Xs2 Xs3 Xs4 Xs5 Xs6 l 0 Z 3 (x)dx Z 4 (x)dx m Σ i=1 X Si Curves, Probability Density Function, and Related Parameters Material ratio curve of the profile (Abbott-Firestone curve) Curve representing the material ratio of the profile as a function of section level c given level c to the evaluation length Pmr(c), Rmr(c), Wmr(c) = Ml(c) ln and λs. Rz JIS = Mean Line c Sampling length Rmr(c),% Material ratio of the primary profile Pmr(c) Material ratio of the roughness profile Rmr(c) Material ratio of the waviness profile Wmr(c) Ratio of the material length of the profile elements Ml(c) at a Section height difference of the primary profile Pδc Section height difference of the roughness profile Rδc Section height difference of the waviness profile Wδc Vertical distance between two section levels of a given material ratio Rδc Rδc = c(rmr1) c(rmr2); Rmr1<Rmr2 c0 c Rmr0 Rmr Relative material ratio of the primary profile Pmr Relative material ratio of the roughness profile Rmr Relative material ratio of the waviness profile Wmr Material ratio determined at a profile section level Rδc (or Pδc or Wδc), related to the reference section level c0 Pmr, Rmr, Wmr = Pmr(c1), Rmr(c1), Wmr(c1) where c1 = c0 Rδc(Rδc, Wδc) c0 = c(pm0, Rmr0, Wmr0) Probability density function (profile height amplitude distribution curve) Sample probability density function of the ordinate Z(x) within the evaluation length Evaluation length Mean line Amplitude density JIS Specific Parameters Ten-point height of irregularities, Rz JIS Sum of the absolute mean height of the five highest profile peaks and the absolute mean depth of the five deepest profile valleys, measured from the mean line within the sampling length of a roughness profile. This profile is obtained from the primary profile using a phase-correct band-pass filter with cutoff values of λc Zp 1 + Zp 2 + Zp 3 + Zp 4 + Zp 5 + Zv 1 + Zv 2 + Zv 3 + Zv 4 + Zv 5 5 Sampling Length for Surface Roughness Parameters ISO 4288: 1996 Table 1: Sampling lengths for aperiodic profile roughness parameters (Ra, Rq, Rsk, Rku, R q), material ratio curve, probability density function, and related parameters Ra µm (0.006)<Ra <Ra <Ra 2 2 <Ra <Ra 80 Table 2: Sampling lengths for aperiodic profile roughness parameters (Rz, Rv, Rp, Rc, Rt) Rz Rz1max µm (0.025)<Rz, Rz1max <Rz, Rz1max <Rz, Rz1max <Rz, Rz1max <Rz, Rz1max 200 1) Rz is used for measurement of Rz, Rv, Rp, Rc, and Rt. 2) Rzlmax only used for measurement of Rzlmax, Rvlmax, Rplmax, and Rclmax. Table 3: Sampling lengths for measurement of periodic roughness profile roughness parameters and periodic or aperiodic profile parameter Rsm Rsm <Rsm <Rsm <Rsm <Rsm <Rsm 4 Procedure for determining a sampling length if it is not specified Estimate Ra, Rz, Rz1max, or RSm according to recorded waveforms, visual inspection, etc. Estimate the sampling length from an estimated value and Tables 1 to 3 Measure Ra, Rz, Rz1max, or RSm according to the estimated value of the sampling length Does each measured value meet the parameter range of Table 1, 2, or 3? Yes Has a shorter sampling length been tried? Yes Measure the parameter according to the final sampling length Fig.1 Procedure for determining the sampling length of an aperiodic profile if it is not specified. Estimate RSm from a measured roughness profile Sampling length lr Sampling length lr Sampling length lr No No Evaluation length ln Evaluation length ln Evaluation length ln Change to a longer or shorter sampling length Change to a shorter sampling length Sampling length Hybrid Parameters Root mean square slope of the primary profile P q Root mean square slope of the roughness profile R q Root mean square slope of the waviness profile W q Root mean square value of the ordinate slopes dz/dx within a sampling length dz (x) dx dz (x) dx dz (x) dx dz (x) dx dz (x) dx Zp 3 Symbol RzJIS82 RzJIS94 Zv 3 Zv 1 Zv 2 1 Ra 75 = ln Zp 2 0 Zv 5 Z(x) dx Zp 4 Zp 5 Sampling length Used profile Surface profile as measured Roughness profile derived from the primary profile using a phase-correct high-pass filter Arithmetic mean deviation of the profile Ra 75 Arithmetic mean of the absolute values of the profile deviations from the mean line within the sampling length of the roughness profile (75%). This profile is obtained from a measurement profile using an analog high-pass filter with an attenuation factor of 12db/octave and a cutoff value of λc. ln Zv 4 Zp 1 Estimate the sampling length from an estimated value and Table 3 Measure RSm according to the estimated value of the sampling length Does the measured value meet the condition of Table 3? Yes Measure the parameter according to the final sampling length No Change the sampling length so as to meet the condition of Table 3 Fig.2 Procedure for determining the sampling length of a periodic profile if it is not specified. 539

19 Contracer CV-1000 and CV-2000 Series Contour Measuring Instruments These are contour measuring instruments with mobile or stationary measurement. The Contracer CV-1000 and CV-2000 offer you the following benefits: Manual positioning meets fully automatic measurement routines. You can easily perform part prograing as well as single measurement with software FORMTRACEPAK. Automatic evaluation, best fit of contours, CAD comparison and many more features come as standard. You can optionally mount the CV-1000 on a granite base with a manual column. You can optionally mount the CV-2000 mounted on a granite base with a manual or power column. Specifications Measuring range CV-1000 : Z1 = 25 CV-1000 : X = 50 CV-2000 : Z1 = 40 CV-2000 : X = 100 0,2 /s; 0,5 /s Measuring speed Accuracy X = (3,5+2L/100) µm [ L : drive length () ] Z1 = (3,5+I4HI/ 25) µm [H : Measurement height from the horizontal position () ] Traverse straightness Column type CV-1000 : 3,5 µm / 50 CV-2000 : 3,5 µm / 100 CV-2000: Power drive = 250 (S4) Manual = 320 (M4) CV-1000 N2 Software FORMTRACEPAK Allows control of measuring conditions for efficient automated measurement. Contour evaluation can be performed using analysis of level differences, angle, pitch, area and contour tolerancing as standard. An inspection certificate can be created by setting the print format as required. FORMTRACEPAK CV-1000N2 mounted on optional granite column Refer to CONTOUR MEASUREMENT brochure CV-2000M4 Stationary contour measuring system with manual column. CV-2000S4 Stationary contour measuring system with motorized column. 540

20 Contracer CV-1000 and CV-2000 Additional Specifications Other optional accessories Optional accessories Other optional and standard accessories are listed later in different sections for accessories and styli. Description Price Cross-travel table 2, XY range : 100x Rotary vice (heavy-duty type) 1, Manual vibration isolator 3, Stand for vibration isolator Column stand for CV-1000 (vertical travel 320, inclination ±45 ) 3, Series Contour Measuring Instruments Specifications and accessories Model CV-1000N2 CV-2000M4 CV-2000S D D D Z2-axis vertical travel Z1-axis measuring range Z2-axis column type Optional: Manual Manual Power X1-axis measuring range Contracer CV-1000 Contracer CV () Accessories Application examples 541

21 Contracer CV-3200 and CV-4500 Series Contour Measuring Instruments These are high accuracy semi-automatic contour measuring instruments equipped with powerful software FORMTRACEPAK. The Contracer CV-3200 offers you the following benefits: Huge measuring range of Z=60 comes as standard. Easy exchange of magnetic stylus arm gives you excellent flexibility. The CV-3200 provides excellent accuracy and resolution in Z1-axis measurement. Its high positioning speed reduces the total measurement time. It has a fully automatic calibration routine. The Contracer CV-4500 offers you the following benefits: It has a dual stylus system for upward/downward measurement at double sided contours. Variable measuring force is controlled by software FORMTRACEPAK. Easy exchange of magnetic stylus arm gives you excellent flexibility. The CV-4500 provides the highest accuracy and resolution possible. The motorised axes have a high positioning speed. The dual stylus system has a fully automatic calibration routine. Specifications Traverse Measuring range Measuring speed Drive speed Accuracy Inclining range Software Additional Specifications Optional accessories Z2 = 300 / 500 Z1 = 60 X = 100 / 200 0,02-5 /s X = 0-80 /s Z2 = 0-30 /s X = (0,8+0,01L) µm (S4, H4, W4 model) X = (0,8+0,02L) µm (S8, H8, W8 model) [ L : Drive length () ] CV-3200 : Z1 = (1,6+I2HI/100) µm CV-4500 : Z1 = (0,8+I2HI/100) µm [ H : Measurement height from the horizontal position () ] ±45 FORMTRACEPAK Other optional and standard accessories are listed later in different sections for accessories and styli. Optional Y-axis Optional Rotary Table θ1-12aad975 Contracer CV-3200 (CV-4500 equipped with dual stylus system) Optional Rotary Table θ Drive unit CV-3200 Refer to Contracer CV-3200 / CV-4500 brochure Drive unit CV

22 Contracer CV-3200 and CV-4500 Specifications Software FORMTRACEPAK Allows control of all axis, optional motordriven Y-axis table and rotary table for efficient automated measurement. Contour evaluation can be performed using analysis of level differences, angle, pitch, area and contour tolerancing as standard. An inspection certificate can be created by setting the print format as required. Series Contour Measuring Instruments Dimensions and specifications S4, (H4), [W4] - Measurement control screen S8, (H8), [W8] - Contour analysis screen CV-3200 Model CV-3200S4 CV-3200H4 CV-3200W4 CV-3200S8 CV-3200H8 CV-3200W D D D D D D Dimensions main unit (WxDxH) 756x482x x482x x482x x482x x482x x482x1176 X1-axis measuring range Vertical travel Granite base size (WxD) 600x x x x x x450 Contour comparison FORMTRACEPAK CV-4500 Model CV-4500S4 CV-4500H4 CV-4500W4 CV-4500S8 CV-4500H8 CV-4500W D D D D D D Dimensions main unit (WxDxH) 756x482x x482x x482x x482x x482x x482x1176 X1-axis measuring range Vertical travel Granite base size (WxD) 600x x x x x x

23 Contracer Extreme CV-3000CNC and CV-4000CNC Series CNC Contour Measuring Instruments Fully CNC contour measuring instrument with powerful software FORMTRACEPAK. Perfectly made for increased throughput of multiple-profiles / -workpieces measurement tasks. Drive speed for each axis up to 200 /s. Continuous measurement over horizontal and inclined surfaces by power-tilting the drive unit. The drive unit of the CV-4000CNC series is equipped with a Laser Hologage detector giving excellent accuracy and resolution in the Z1-axis. Inclined plane measurement through 2-axis simultaneous control in the X and Y directions. The detector unit incorporates an anti-collision safety device, causing the detector unit to automatically stop if its main body collides with a workpiece or jig. Specifications Measuring range Measuring speed Drive speed Z1 = 50 X = 200 Y = 200 Z2 = 300 / 500 0,02-2 /s CNC mode: max.200 /s Joystick mode: 0-60 /s Accuracy CV-3000CNC : X = (1+0,02L) µm Y = 200 Z1 = (2+I4HI/100) µm CV-4000CNC : X = (0,8+0,02L) µm Z1 = (0,8+I0,5HI/25) µm [ L : Drive length () ] [ H : Measurement height from the horizontal position () ] Inclining +45 (CCW) to -10 (CW) range Software FORMTRACEPAK CV-3000CNC Series CNC Contour Measuring Instrument CV-3000CNC Model CV-3000CNC-S CV-3000CNC-S. CV-3000CNC-H CV-3000CNC-H Dimensions main unit (WxDxH) 800x620x x620x x620x x620x1200 Z2-axis vertical travel Y-axis table unit - Installed - Installed α-axis unit Installed Installed Installed Installed Specifications Optional Accessories Mechanism Natural frequency Hz (dann range) Leveling Max. loading capacity Air pressure Mass Dimensions (WxDxH) Vibration isolation stand Diaphragm air spring 2,5-3,5 Automatic control with mechanical valves 350 kg 390 kpa 280kg 1000 x 895 x 715 CV-4000CNC Model CV-4000CNC-S CV-4000CNC-S Dimensions main unit (WxDxH) 800x620x x620x1000 Z2-axis vertical travel Y-axis table unit - Installed α-axis unit Installed Installed Additional Specifications Optional accessories Other optional and standard accessories are listed later in different sections for accessories and styli. Refer to CONTOUR MEASUREMENT brochure CV-4000CNC Extreme Model CV-4000CNC-H CV-4000CNC-H Dimensions main unit (WxDxH) 800x620x x620x1200 Z2-axis vertical travel Y-axis table unit - Installed α-axis unit Installed Installed 544

24 Quick Guide to Precision Measuring Instruments Traceable Angle The maximum angle at which a stylus can trace upwards or downwards along the contour of a workpiece, in the stylus travel direction, is referred to as the traceable angle. A one-sided sharp stylus with a tip angle of 12 (as in the above figure) can trace a maximum 77 of up slope and a maximum 87 of down slope. For a conical stylus (30 cone), the traceable angle is smaller. An up slope with an angle of 77 or less overall may actually include an angle of more than 77 due to the effect of surface roughness. Surface roughness also affects the measuring force. For model CV-3200/4500, the same type of stylus (SPH-71: one-sided sharp stylus with a tip angle of 12 ) can trace a maximum 77 of up slope and a maximum 83 of down slope. Compensating for Stylus Tip Radius A recorded profile represents the locus of the center of the ball tip rolling on a workpiece surface. (A typical radius is ) Obviously this is not the same as the true surface profile so, in order to obtain an accurate profile record, it is necessary to compensate for the effect of the tip radius through data processing. RxM Up slope 77 or less 87 or less Down slope Stylus Contracer (Contour Measuring Instruments) Overload Safety Cutout If an excessive force (overload) is exerted on the stylus tip due, perhaps, to the tip encountering a too-steep slope on a workpiece feature, or a burr, etc., a safety device automatically stops operation and sounds an alarm buzzer. This type of instrument is coonly equipped with separate safety devices for the tracing direction (X axis) load and vertical direction (Y axis) load. For model CV-3200/4500, a safety device functions if the arm comes off the detector mount. Simple or Complex Arm Guidance In the case of a simple pivoted arm, the locus that the stylus tip traces during vertical movement (Z direction) is a circular arc that results in an unwanted offset in X, for which compensation has to be made. The larger the arc movement, the larger is the unwanted X displacement (δ) that has to be compensated. (See figure, lower left.) The alternative is to use a complex mechanical linkage arrangement to obtain a linear translation locus in Z, and therefore avoid the need to compensate in X. Z axis Measurement Methods Though the X axis measurement method coonly adopted is by means of a digital scale, the Z axis measurement divides into analog methods (using a differential transformer, etc.) and digital scale methods. Analog methods vary in Z axis resolution depending on the measurement magnification and measuring range. Digital scale methods have fixed resolution. Recorded profile Workpiece contour R: Stylus tip radius M: Measurement magnification RxM RxM Compensating for Arm Rotation The stylus is carried on a pivoted arm so it rotates as the surface is traced and the contact tip does not track purely in the Z direction. Therefore it is necessary to apply compensation in the X direction to ensure accuracy. There are three methods of compensating for arm rotation. 1: Mechanical compensation 2: Electrical compensation δ Stylus Measuring arm Fulcrum δ: Unwanted displacement in X to be compensated 3: Software processing. To measure a workpiece contour that involves a large displacement in the vertical direction with high accuracy, one of these compensation methods needs to be implemented. 545

25 Contour analysis methods You can analyze the contour with one of the following two methods after completing the measurement operation. Data processing section and analysis program The measured contour is input into the data processing section in real time and a dedicated program performs the analysis using the mouse and/or keyboard. The angle, radius, step, pitch and other data are directly displayed as numerical values. Analysis combining coordinate systems can be easily performed. The graph that goes through stylus radius correction is output to the printer as the recorded profile. Data Combination Conventionally, if tracing a complete contour is prevented by stylus traceable-angle restrictions then it has to be divided into several sections that are then measured and evaluated separately. This function avoids this undesirable situation by combining the separate sections into one contour by overlaying coon elements (lines, points) onto each other. With this function the complete contour can be displayed and various analyses performed in the usual way. Data 1 Data 2 Tolerancing with Design Data Measured workpiece contour data can be compared with design data in terms of actual and designed shapes rather than just analysis of individual dimensions. In this technique each deviation of the measured contour from the intended contour is displayed and recorded. Also, data from one workpiece example can be processed so as to become the master design data to which other workpieces are compared. This function is particularly useful when the shape of a section greatly affects product performance, or when its shape has an influence on the relationship between mating or assembled parts. Best-fitting If there is a standard for surface profile data, tolerancing with design data is performed according to the standard. If there is no standard, or if tolerancing only with shape is desired, best-fitting between design data and measurement data can be performed. Data combination Measurement Examples <Before best-fit processing> <After best-fit processing> Measured data Measured data Dual stylus for upward and downward measurement Inner/outer ring contour of a bearing Design data Design data The best-fit processing algorithm searches for deviations between both sets of data and derives a coordinate system in which the sum of squares of the deviations is a minimum when the measured data is overlaid on the design data. Internal gear teeth Female thread form Male thread form Gage contour 546

26 Specifications Traverse Measuring range Measuring speed Drive speed Accuracy Inclining range Software Z2 = 300 / 500 X = 100 / 200 Contour: Z1 = 60 Roughness: Z1 = 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) 0,02-5 /s X = 0-80 /s Z2 = 0-30 /s X = (0,8+0,01L) µm (S4, H4, W4 model) X = (0,8+0,02L) µm (S8, H8, W8 model) [ L : Drive length () ] SV-C3200 : Z1 = (1,6+I2HI/100) µm SV-C4500 : Z1 = (0,8+I2HI/100) µm [ H : Measurement height from the horizontal position () ] ±45 FORMTRACEPAK Formtracer SV-C3200 and SV-C4500 Series Surface and Contour Measuring System These are high accuracy semi-automatic contour and roughness measuring instruments equipped with powerful software FORMTRACEPAK. The Formtracer SV-C3200 offers you the following benefits: It is as powerful as two separate, specialised instruments. It economically combines roughness & contour measurement into a single device. You have access to a huge contour measuring range of Z=60 as standard, and a roughness measurement range of 800µm as standard. Easy exchange of the magnetic contour stylus arm gives you excellent flexibility. The SV-C3200 provides you with excellent accuracy and resolution in Z1-axis measurement. The Formtracer SV-C4500 offers you the following benefits: It economically combines roughness & dual stylus upward/downward contour measurement into a single device. You have access to a huge contour measuring range of Z=60 as standard, and a roughness measurement range of 800µm as standard. Its variable measuring force is controlled by software FORMTRACEPAK. Easy exchange of the magnetic contour stylus arm gives you excellent flexibility. The SV-C4500 provides you with high accuracy and resolution. Additional Specifications Optional accessories Other optional and standard accessories are listed later in different sections for accessories and styli. Refer to Formtracer SV-C3200 / 4500 brochure Formtracer SV-C3200 Surface Roughness drive unit [Surface Roughness Measurement : Compliant with EN ISO, VDA, JIS, ANSI and other international surface roughness standards. ] Contour drive unit SV-C3200 Contour drive unit SV-C

27 Formtracer SV-C3200 and SV-C4500 Series Surface and Contour Measuring System Specifications Metric SV-C3200 Model Detector 0,75 mn D-1 SV-C3200S D-2 " D-1 SV-C3200H D-2 " D-1 SV-C3200W D-2 " D-1 SV-C3200S D-2 " D-1 SV-C3200H D-2 " D-1 SV-C3200W D-2 " Detector 4 mn Z2-axis 300 Z2-axis 500 X-axis 100 X-axis 200 Software FORMTRACEPAK Allows control of all axis, optional motordriven Y-axis table and rotary table for efficient automated measurement. Surface roughness analyisis and contour evaluation can be performed using analysis of level differences, angle, pitch, area and contour tolerancing as standard. An inspection certificate can be created by setting the print format as required. Metric SV-C4500 Model Detector 0,75 mn D-1 SV-C4500S D-2 " D-1 SV-C4500H D-2 " D-1 SV-C4500W D-2 " D-1 SV-C4500S D-2 " D-1 SV-C4500H D-2 " D-1 SV-C4500W D-2 " Detector 4 mn Z2-axis 300 Z2-axis 500 X-axis 100 X-axis 200 Measurement control screen Contour analysis screen Using Y-axis table Using rotary table θ1 Using rotary Table θ2 Contour comparison Roughness analysis 548

28 Formtracer CS-3200 Specifications Traverse Z2 = 300 Measuring X = 100 range Z1 = 5 (up to 10 with an optional stylus) Measuring Roughness measurement: speed 0,02 / 0,05 / 0,1 / 0,2 /s Contour measurement: 0,02 / 0,05 / 0,1 / 0,2 / 0,5 / 1 / 2 /s Drive speed X = 0-80 /s Z2 = 0-20 /s Accuracy X = (0,8+0,01L) µm [ L : Drive length () ] Z1 = (1,5+I2HI/100) µm H : Measurement height from the horizontal position () Inclining ±45 range Traverse X = 0,2 µm / 100 straightness Series Surface and Contour Measuring System This provides all-in-one surface roughness and contour measurement within one drive unit. The Formtracer CS-3200 offers you the following benefits: You can carrying out simultaneous analysis of roughness and contour with one measurement. It complies with many standards including EN ISO, VDA, ANSI and JIS as well as customised settings. It gives you the best measuring condition with a vibration stand as standard. The high drive speed reduces the total measurement time. The detector unit can be extended to avoid interference between the drive unit and workpiece. Software FORMTRACEPAK-6000 Allows control of all axis, optional motor-driven Y-axis table and rotary table for efficient automated measurement. Surface roughness analyisis and contour evaluation can be performed using analysis of level differences, angle, pitch, area and contour tolerancing as standard. An inspection certificate can be created by setting the print format as required. Refer to Formtracer CS-3200 brochure CS3200S4 (with optional Y-axis ) 1: Outside diameter 2: Outside diameter 3: Inside diameter 4: Measurement element 5: Positioning element Continuous measurement example: The drive unit (X-axis) and column (Z2-axis) are equipped with high-accuracy linear scales (ABS type) enabling fully automatic measurement combining vertical and horizontal movement. This improves reproducibility of continuous automatic measurement of small holes in the vertical direction and repeated measurements of parts which are difficult to position. 549

29 Formtracer CS-3200 Series Surface and Contour Measuring System Specifications and Styli Additional Specifications Optional accessories Other optional and standard accessories are listed later in different sections for accessories and styli. Model CS-3200S D Z2-axis vertical travel 300 X1-axis measuring range ø3 ø3 10 ø1.2 8 ø AAD554 Standard stylus Radius of tip curvature = 2 µm Tip Material: Diamond ø AAD552 Cone stylus Radius of tip curvature = 25 µm Tip Material: Sapphire 3.2 Measuring instrument control ø4 ø4 ø ø (6.5) AAD556 Small hole stylus Radius of tip curvature = 2 µm Tip Material: Diamond ø (8) ø AAD558 Eccentric type stylus Radius of tip curvature = 2 µm Tip Material: Diamond (6.5) 3.2 Contour analysis screen ø1.2 ø ø AAD560 Deep groove stylus Radius of tip curvature = 2 µm Tip Material: Diamond (6.5) Contour analysis screen ø ø ø Contour and roughness layout (6.5) 12AAD562 2x-long stylus* 1 Radius of tip curvature = 5 µm Tip Material: Diamond * 1 : Measuring force is 4mN and the Z1 measuring and resolution is double that of the standard stylus. 550

30 Formtracer Extreme SV-C3000CNC and SV-C4000CNC Specifications Traverse Measuring range Measuring speed Drive speed Z2 = 300 / 500 X = 200 Y = 200 Contour : Z1 = 50 Roughness : Z1 = 800 µm; 80 µm; 8 µm (up to 2,4 with an optional stylus) 0,02-2 /s CNC mode: max. 200 /s Joystick mode: 0-60 /s Accuracy X = (1+0,02L) µm [ L : Drive length () ] SV-C3000CNC : Z1 = (2+I4HI/100) µm SV-C4000CNC : Z1 = (0,8+I0,5HI/25) µm [ H : Measurement height from the horizontal position () ] Inclining +45 (CCW) to -10 (CW) range Measuring 0,75 mn / 4 mn models force Series Surface and Contour Measuring Instrument These are high accuracy fully CNC surface and contour measuring instruments. The Formtracer Extreme SV-C3000CNC/SV-C4000CNC offer you the following benefits: They are as powerful as two separate, fully CNC instruments. Each axis has a drive speed of up to 200 /s. They are perfectly made for increased throughput of multiple profile and workpiece measurement tasks. You can take continuous measurement over horizontal and inclined surfaces by power-tilting the drive unit. The contour drive unit of SV-C4000CNC series is equipped with a Laser Hologage detector giving you excellent narrow/wide range accuracy and resolution in the Z1-axis. The detector unit incorporates an anti-collision safety device, causing it to automatically stop if its main body collides with a workpiece or jig. It is supplied with an easy-to-operate remote box. Software FORMTRACEPAK Refer to CONTOUR AND SURFACE MEASUREMENT brochure SV-C3000CNC Surface Roughness drive unit Contour drive unit 551

31 Formtracer Extreme SV-C3000CNC and SV-C4000CNC Series Surface and Contour Measuring Instrument SV-C3000CNC Model SV-C3000CNC-S SV-C3000CNC-S. SV-C3000CNC-H SV-C3000CNC-H Z2-axis vertical travel Y-axis table unit - Installed - Installed α-axis unit Installed Installed Installed Installed Specifications Optional Accessories Mechanism Natural frequency Hz (dann range) Leveling Max. loading capacity Dimensions (WxDxH) Air pressure Vibration isolation stand Diaphragm air spring 2,5-3,5 Automatic control with mechanical valves 350 kg 1000 x 895 x KPa SV-C4000CNC Model SV-C4000CNC-S SV-C4000CNC-S. SV-C4000CNC-H SV-C4000CNC-H Z2-axis vertical travel Y-axis table unit - Installed - Installed α-axis unit Installed Installed Installed Installed Additional Specifications Optional accessories Software Other optional and standard accessories are listed later in different sections for accessories and styli. FORMTRACEPAK Allows control of all axis, optional motor-driven Y-axis table and rotary table for efficient automated measurement. Contour evaluation can be performed using analysis of level differences, angle, pitch, area and contour tolerancing as standard. An inspection certificate can be created by setting the print format as required. Z2-axis Y-axis α-axis Contour analysis Through 2-axis simultaneous control in the X and Y directions Roughness analysis Multiple measurements 552

32 Specifications Traverse Measuring range Measuring speed Drive speed Accuracy Traverse straightness Resolution [µm] Software Z2 = 300 / 500 X = 200 Z1 = 12 [standard lenght stylus ] Z1 = 24 [double lenght stylus ] Roughness measurement: 0,02-0,2 /s Contour measurement: 0,02-2 /s CNC mode: max. 200 /s Joystick mode 0-50 /s CS-5000CNC: X = (0,3+0,002L) µm Z1 = (0,3+I0,02HI) µm CS-H5000CNC: X = (0,16+0,001L) µm Z1 = (0,07+I0,02HI) µm [ L : Drive length () ] [ H : Measurement height from the horizontal position () ] CS-5000CNC: X = (0,1+0,0015L) µm [ standard stylus ] X = (0,2+0,0015L) µm [ double length stylus ] CS-H5000CNC: X = (0,05+0,0003L) µm [ standard stylus ] X = (0,1+0,0015L) µm [ double length stylus ] X = 0,00625 µm CS-5000CNC: Z1 = 0,004 µm [ standard stylus ] Z1 = 0,008 µm [ double length stylus ] CS-H5000CNC: Z1 = 0,001 µm [ standard stylus ] Z1 = 0,002 µm [ double length stylus ] FORMTRACEPAK Formtracer Extreme CS-5000CNC and CS-H5000CNC Series CNC Surface and Contour Measuring Instruments This is the highest-accuracy stylus type CNC surface roughness and contour measuring instrument. The Formtracer Extreme CS-5000CNC / CS-H5000CNC offers you the following benefits: It meets the highest demands of accuracy and repeatability. You can carry out simultaneous analysis of roughness and contour within one measurement. It cabin includes a vibration stand as standard to avoid external influences. A Mitutoyo Laser Holoscale is incorporated in the X1- and Z1-axes so you can achieve high resolution of X1-axis : 6.25 nm and Z1-axis : 4nm/8nm. The X1 and Z2-axis have maximum drive speeds of 40/s and 200/s respectively. Refer to CONTOUR AND SURFACE MEASUREMENT brochure CS-H5000CNC 553

33 Formtracer Extreme CS-5000CNC and CS-H5000CNC Series CNC Surface and Contour Measuring Instruments Specifications and Styli CS-5000CNC Model CS-5000CNC-1S CS-5000CNC-2S CS-5000CNC-3S CS-5000CNC-4S Z2-axis vertical travel Y-axis table unit - - Installed Installed α-axis unit - Installed - Installed Model CS-5000CNC-1H CS-5000CNC-2H CS-5000CNC-3H CS-5000CNC-4H Z2-axis vertical travel Y-axis table unit - - Installed Installed α-axis unit - Installed - Installed Specifications Software FORMTRACEPAK Allows control of all axis, optional motordriven Y-axis table and rotary table for efficient automated measurement. Surface roughness analysis and contour evaluation can be performed using analysis of level differences, angle, pitch, area and contour tolerancing as standard. An inspection certificate can be created by setting the print format as required. CS-H5000CNC Model CS-H5000CNC-1S CS-H5000CNC-2S Z2-axis vertical travel Y-axis table unit - Installed α-axis unit - - Contour and roughness analysis (31.5) Ø6 12AAD543 12AAD544 12AAJ037 Ø6 Ø6 1 Ø Ø Ø Ø Standard (6.5) (6.8) 187 (31.5) Ø6 40º Ø0.5 12AAD545 12AAD546 12AAJ039 12AAJ Ø6 Ø6 40º Ø6 Optional: Aspherical lens analysis program ASLPAK Ø6 Ø4 Ø1.2 Ø Ø1.2 Ø1.2 (19) Double length / (31.5) 40º AAD651 Ø0.5 40º 12AAD º 6 15 / 10 Ø6 Ø (1.1) º Ø º Ø0.6 For small holes (31.5) 12AAD653 Ø Ø4 Ø6 Ø1.2 (6.5) º Eccentric Nosepiece Detector 1 = additional for CS-H5000CNC 554

34 Optional Software USB Counication Tool Optional accessories Description Price 12AAL068D USB cable for SJ AAD510 USB cable for SJ-310 / SJ AAH490 USB cable for SJ-500 / SV-2100 Series Control Software for SJ series, SV-2100 This is control software for Surftest SJ-210 / SJ-310 / SJ-410 / SJ-500 and SV-2100 which offers you the following benefits: It is available as a free download on Output software is based on Microsoft Excel for controlling the devices, reproducing and storing measurement data. Measurement device control. It provides definition of measurement variables. Graphic representation of the profile. Storage of measurement records. Documentation of measurements result. A USB connecting cable is necessary. Input mask for Surftest SJ series Output record from Microsoft Excel Output record from Microsoft Excel in 18 languages as standard. 555

35 Optional Styli for Surftest and Formtracer SV-C series ø7 4 ø ø14 14 ø8 Specifications Probes : 0,75 mn measuring force with the standard stylus 12AAC731 (radius 2 µm, angle 60 ) : 4 mn measuring force with stylus 12AAB403 (radius 5 µm, angle 90 ) : Detector 0.75 mn : Detector 4 mn Stylus Nose pad Standard A ø /90 Radius Angle Price 12AAE882 1 µm 60 1, AAE924 1 µm 90 1, AAC731 2 µm AAB403 5 µm AAB µm AAE µm Price 12AAB For small hole 0.6 ø / A ø Radius Angle Price 12AAC732 2 µm AAB404 5 µm AAB µm AAB For extra small hole 0.4 ø / A ø Radius Angle Price 12AAC733 2 µm AAB405 5 µm AAB µm Price 12AAB Radius Angle Price 12AAJ µm A Ultra small hole 0.8 For extra minute hole ø / A ø Radius Angle Price 12AAC734 2 µm AAB406 5 µm AAB µm AAB

36 Optional Styli for Surftest and Formtracer SV-C series 3 For deep hole (double-length) Stylus for deep groove 30/ A ø1.2 Radius Angle Price 12AAC740 2 µm AAB413 5 µm AAB µm A Radius Angle Price 12AAC737 2 µm AAB407 5 µm AAB µm /90 ø / ø1.2 Radius Angle Price 12AAE µm 60 1, Radius Angle Price 12AAE894 2 µm AAE910 5 µm ø A 30 ø Radius Angle Price 12AAE892 2 µm AAE908 5 µm ø1.2 Ø3 30 Double-length Radius Angle Price 12AAE898 2 µm AAE914 5 µm Ø2.4 Radius Angle Price 12AAE895 2 µm AAE911 5 µm ø0.6 ø Radius Angle Price 12AAE938 2 µm AAE940 5 µm Ø A ø1.2 For deep hole (triple-length) Stylus for rolling circle waviness surface roughness ( required) / A ø1.2 Radius Angle Price 12AAC741 2 µm AAB414 5 µm AAB µm ø1.2 ø1.588 Radius Price 12AAB Radius Price 12AAE ø1.2 For bottom surface Stylus for eccentric arm ø Radius Angle Price 12AAE899 2 µm 60 1, AAE915 5 µm 90 1, A 60 / ø1.2 Radius Angle Price 12AAC739 2 µm AAB412 5 µm AAB µm /90 For corner hole Radius Angle Price 12AAM601 2 µm AAM603 5 µm

37 60 /90 Optional Styli for Surftest and Formtracer SV-C series For deep groove 10 Nose pad A ø Radius Angle Price 12AAC735 2 µm AAB409 5 µm AAB µm Price 12AAB /90 Price 12AAC For deep groove 20 Nose pad A ø1.2 Radius Angle Price 12AAC736 2 µm AAB408 5 µm AAB µm Price 12AAB /90 Radius Angle Price 12AAE893 2 µm AAE909 5 µm For gear teeth Nose pad ø1.2 A Radius Angle Price 12AAB339 2 µm AAB410 5 µm AAB µm Price 12AAB Radius Angle Price 12AAE896 2 µm AAE912 5 µm ø ø1.2 Double-length For Knife edge detector Nose pad 0.9 A /90 ø Radius Angle Price 12AAC738 2 µm AAB411 5 µm AAB µm Price 12AAC

38 ø4 ø5 ø4 Optional Styli and Arms for Contracer and Formtracer SV-C Series ø6 ø8 ø8 ø8 h ø H ø H H ø Small hole : / 12AAE873 Tip shape : Single bevel / Cone Tip angle : 20 / 30 Tip radius : 25 µm / 25 µm Tip material : Carbide / Carbide Arm Straight type CV-1000/2000 Arm Eccentric type CV-1000/2000 Arm for small-hole stylus CV-1000/2000 Arm for small-hole stylus CV-1000/2000 h 1 ø3 20 Small hole : / 12AAE874 Tip shape : Single bevel / Cone Tip angle : 20 / 30 Tip radius : 25 µm / 25 µm Tip material : Carbide / Carbide 50 ø6 Applicable Arms for CV-1000 and CV-2000 Arm Compatible stylus height (H) Price [ ] Small hole 0,4 / 1 / 2, Straight type Straight type Straight type Straight type Straight type Eccentric type Eccentric type Eccentric type h 2.5 ø4 Small hole : / 12AAE875 Tip shape : Single bevel / Cone Tip angle : 20 / 30 Tip radius : 25 µm / 25 µm Tip material : Carbide / Carbide H ø Small hole : 12AAE297 Tip shape : Single bevel Tip angle : 20 Tip radius : 25 µm Tip material : Carbide ø8 Applicable Arms for CV-3000CNC/4000CNC and SV-C3000CNC/4000CNC Arm Compatible stylus height (H) Price [ ] 12AAE294 Straight type AAE295 Straight type Straight type Straight type Straight type Eccentric type Eccentric type Eccentric type Eccentric type Eccentric type AAE296 Small hole Small-hole stylus Applicable Arms for CV-3200 / CV-4500 and SV-C3200 / SV-C4500 Arm Compatible stylus height (H) 12AAM101 Straight type all 12AAM102 Eccentric type all 12AAM103 Small hole Small-hole stylus H 20ø3 55 Small hole : 12AAE298 Tip shape : Single bevel Tip angle : 20 Tip radius : 25 µm Tip material : Carbide Applicable Styli for CV-1000 and CV-2000 Stylus Stylus height (H) Price [ ] Small hole, carbide-tipped one-sided cut Small hole, carbide-tipped one-sided cut Small hole, carbide-tipped one-sided cut 6, AAE873 Small hole, carbide-tipped cone AAE874 Small hole, carbide-tipped cone AAE875 Small hole, carbide-tipped cone 6, H 55 Small hole : 12AAE299 Tip shape : Single bevel Tip angle : 20 Tip radius : 25 µm Tip material : Carbide Applicable Styli for CV-3000CNC/4000CNC and SV-C3000CNC/4000CNC Stylus Stylus height (H) Price [ ] 12AAE297 Small hole, carbide tipped one-sided cut AAE298 Small hole, carbide tipped one-sided cut AAE299 Small hole, carbide tipped one-sided cut 6,

39 Optional Styli and Arms for Contracer and Formtracer SV-C Series Styli Applicable Styli for CV-1000/2000, CV-3200/4500, CV-3000CNC/4000CNC, SV-C3200/4500 and SV-C3000CNC/4000CNC Stylus Stylus height (H) Price [ ] Single bevel, carbide tipped Single bevel, carbide tipped Single bevel, carbide tipped Single bevel, carbide tipped Single bevel, carbide tipped Cross ground, carbide tipped Cross ground, carbide tipped Cross ground, carbide tipped Cross ground, carbide tipped Cross ground, carbide tipped AAE865 Cone, carbide-tipped angle AAE866 Cone, carbide-tipped angle AAE867 Cone, carbide-tipped angle AAE868 Cone, carbide-tipped angle AAE869 Cone, carbide-tipped angle Cone, sapphire-tipped angle Cone, sapphire-tipped angle Cone, sapphire-tipped angle Cone, diamond-tipped angle Cone, sapphire-tipped angle Cone, sapphire-tipped angle AAA566 Cone, carbide-tipped angle AAA567 Cone, carbide-tipped angle AAA568 Cone, carbide-tipped angle AAA569 Cone, carbide-tipped angle AAA570 Cone, carbide-tipped angle Knife edge, carbide tipped Knife edge, carbide tipped Knife edge, carbide tipped Knife edge, carbide tipped Knife edge, carbide tipped Ball, carbide tipped Ball, carbide tipped Ball, carbide tipped Ball, carbide tipped Ball, carbide tipped Single bevel Tip angle : 12 Tip radius : 25 µm Tip material : Carbide Cross ground Tip angle : 20 Tip radius : 25 µm Tip material : Carbide ø3 H Cone Tip angle : 30/50 Tip radius : 25 µm Tip material : Carbide/Sapphire/Diamond ( : 50, Diamond) Applicable Styli for CV-3200 / 4500 and SV-C3200 / 4500 Stylus Stylus height (H) 12AAM104 Small hole, carbide tipped one sided cut 2 12AAM105 Small hole, carbide tipped one sided cut 4 12AAM106 Small hole, carbide tipped one sided cut 6,5 Cone Tip angle : 20 Tip radius : 25 µm Tip material : Carbide Applicable Styli for only CV-4500 and SV-C4500 Stylus Stylus height (H) 12AAM095 Both sides conical stylus 20 12AAM096 Both sides conical stylus 32 12AAM097 Both sides conical stylus 48 12AAM108 Both sides small hole arm stylus 2,4 12AAM109 Both sides small hole arm stylus 5 12AAM110 Both sides small hole arm stylus 9 Knife edge Tip angle : 20 Edge width : 3 Tip radius : 25 µm Tip material : Carbide Ball Ball : ø1 Tip material : Carbide 560

40 Optional Accessories for Surftest, Contracer and Formtracer For SV series, SV-C series, CV series, CS series and CNC Models Automatic-leveling table : (for SV, CV, SV-C, CS) Automatic-leveling table : (for CNC Models) This is a stage that performs fully automatic leveling as measurement starts, freeing the user from this troublesome operation. Fully automatic leveling can be done quickly by anyone. In addition, the operation is easy and reliable. Inclination adjustment angle Maximum load Table dimensions [kg] ± x ± x 100 Using Micro-chuck This chuck is suitable for clamping extra-small diameter workpieces (ø1.5 or less), which cannot be retained with the centering chuck. Dimensions Retention range ø118 x 48,5 OD : ø0 - ø1, Quick chuck This Chuck is useful when measuring small workpieces. You can easily clamp them with its knurled ring. Dimensions Retention range ø118 x 41 Inner latch : OD ø1 - ø36 Inner latch : ID ø16 - ø69 outer latch : OD ø25 - ø79 Y-axis table for SV-3100, SV-C, CS and CV models (not CNC models) Enables efficient, automatic measurement of multiple aligned workpieces and multiple points on a single measurement surface. It allows semi-automatic measurement with a semi-automatic with non CNC models by using these items. Resolution Travel range Positioning accuracy Maximum load Drive speed [µm] [µm] [kg] , ±3 50 Max. 80 /s θ1-axis:*¹ For efficient measurement in the axial / transverse directions. When measuring a cylindrical workpiece, automatic alignment can be performed in combination with the Y-axis table. *¹ = 12AAE630 mounting plate is required when directly installing on the base of the machine. Resolution Rotational speed Displacement Maximum load [kg] 12AAD975 0,004 Max. 10 /s AAD975 θ2-axis:*¹ For efficent measurment of multiple points on a cylindrical workpiece and automate front/rear-side measurement. *¹ = 12AAE718 mounting plate is required when directly installing on the base of the machine. *¹ = 12AAE705 attachment plate is required when installing on θ1-axis table. *¹ = 12AAE707 mounting plate is required when directly installing on Y-axis table with automatic leveling table. Maximum load Resolution Rotational speed Displacement [kg] ,0072 Max. 18 /s using Y-axis 12AAD975 using θ1-axis using θ2-axis 561

41 Optional Accessories for Surftest, Contracer and Formtracer 3 - Axis Adjustment Table Description This table helps make the alignment adjustments required when measuring cylindrical surfaces. The corrections for the pitch angle and the swivel angle are determined from a preliminary measurement and the Digimatic micrometers are adjusted accordingly. A flat-surfaced workpiece can also be leveled with this table. Price [ ] 4, Calibration Stand Description Price [ ] 12AAG175 For mounting a roughness specimen or step gauge during calibration AAG175 Cross-travel Table Table top XY travel Price [ ] x x 50 2, x x 25 2, Digital Leveling Table Table top XY travel Price Leveling range [ ] x 100 ±12,5 ±1,5 3, Leveling Table Table top XY travel Price Leveling range [ ] x 100 ±12,5 ±1,5 2, x ±1, Precision Vise Description Price [ ] Max. workpiece size : 36 Can be mounted on a leveling table Rotary Vice Description Two-slide jaw type Max. workpiece size : ø60 Minimum reading : 1 Price [ ] 1, V-Block Description Workpiece diameter : 1 to 160 Can be mounted on a leveling table Price [ ]

42 Specifications Turntable Rotational accuracy Max. probing Ø Max. workpiece Ø Max. turntable loading Vertical column Vertical travel Max. probing height Display unit Data analysis items Printer Radial: (0,04+0,0006H)µm H: Measuring height from turntable surface () Axial: (0,04+0,0006X)µm X: Radial distance from center () kg Roundness, Coaxiality, Concentricity, Flatness, Runout radial Built-in thermal line printer Roundtest RA-10 Series Form Measuring Instrument This is a compact and affordable form measuring instrument. The Roundtest RA-10 offers you the following benefits: It combines outstanding cost and performance with full measurement capabilities. The machine has a compact body with integrated electronics and printer, making it ideal for installation in space-restricted locations. Despite being a low-priced model, the turntable with air bearings gives you rotational accuracy as high as ( H)µm, assuring a precision that compares well with that of higher priced models. The control panel has large keys and an intuitive layout for easy operation. One-touch setup recall. Zero-set function. You can easily view measurement results and recorded profiles on the large LCD panel display. RA-10 with optional X-axis stop and Z-axis scale unit Z-axis scale unit X-axis stop 563

43 Roundtest RA-10 Series Form Measuring Instrument Dimensions and accessories Optional accessories Description 12AAH402 Collet (ø0,5-1,0 ) 12AAH403 Collet (ø1,0-1,5 ) 12AAH404 Collet (ø1,5-2,0 ) 12AAH405 Collet (ø2,0-2,5 ) 12AAH406 Collet (ø2,5-3,0 ) 12AAH407 Collet (ø3,0-3,5 ) 12AAH408 Collet (ø3,5-4,0 ) 12AAH409 Collet (ø4,0-5,0 ) 12AAH410 Collet (ø5,0-6,0 ) 12AAH411 Collet (ø6,0-7,0 ) 12AAH412 Collet (ø7,0-8,0 ) 12AAH413 Collet (ø8,0-9,0 ) 12AAH414 Collet (ø9,0-10,0 ) Vibration damping stand Reference hemisphere Micro-chuck OD: 1-1, Quick chuck OD: 1-79, ID: Magnification checking gauge Collet chuck (OD : 0,5-10 ) Quick chuck V-block jig A (for ø50 ) V-block jig B (for ø50 ) 12AAH420 Spacer for reference hemisphere 12AAH425 Alignment table with D.A.T. () 12AAH427 Alignment table with mechanical heads 12AAH318 Z-axis scale unit 12AAH320 X-axis stop Auxiliary stage for a low-height workpiece Gauge block set for calibration Consumable spares 12AAH181 Description Printer paper (10 rolls) AAH425 Max. workpiece ø Max. probing Ø Max. turntable loading Model [kg] D RA

44 Roundtest RA-120 and RA-120P Specifications Turntable Rotational accuracy Max. probing Ø Max. workpiece Ø Max. turntable loading Centering range ±3 Leveling range ±1 Radial: (0,04+0,0006H)µm H: Measuring height from turntable surface () Axial: (0,04+0,0006X)µm X: Radial distance from center () kg Series Form Measuring Instrument These are compact, affordable and simple-to-use instruments for measuring roundform geometry. The Roundtest RA-120 and 120P offer you the following benefits: The turntable accuracy of ( H)µm provides high level form analysis. The RA-120 has a compact body with integrated electronics and printer, making it ideal for installation in space-restricted locations. The RA-120P is a PC based model with all operations controlled via powerful ROUNDPAK software. Software ROUNDPAK gives you excellent possibilities for single measurement and part prograing. Vertical column Vertical travel Max. probing height Max. probing depth Display unit Data analysis items Printer Software above turntable surface 480 in reverse position 100 (minimum ID: 30 ) Only RA-120 (Roundpak-120P with PC) Roundness, Coaxiality, Flatness, Runout (radial), Runout (axial), Thickness deviation, Parallelism, Perpendicularity Built-in thermal line printer ROUNDPAK (only RA-120P) RA-120 Z-axis scale unit (optional) RA-120P X-axis stop 565

45 Roundtest RA-120 and RA-120P Series Form Measuring Instrument The is a compact roundness tester with D.A.T. (Digital Adjustment Table) function. The Roundtest RA-120 and 120P give you the following benefits: The turntable displays centering and leveling adjustments digitally, making this challenging task easy enough for even an untrained operator to perform, through these four simple steps: 1. Preliminary measurement of two cross sections on the workpiece. 2. The centering and leveling adjustment values are displayed. 3. The digital micrometer heads on the rotary table are adjusted to match the values displayed. 4. Centering and leveling is complete. [Centering range : ±3 - Leveling range : ±1 ] Additional Specifications Optional accessories Optional accessories Other optional and standard accessories are listed later in this section for accessories and styli. Description Vibration damping stand Three jaw chuck OD: 2-78, ID: Reference hemisphere Micro-chuck OD: 1-1, Quick chuck OD: 1-79, ID: Magnification checking gauge Collet chuck OD: 0, AAH320 X-axis stop Auxiliary stage for a low-height workpiece Gauge block set for calibration Consumable spares Description 12AAH181 Printer paper (10 rolls) Model Max. workpiece ø Max. probing Ø Max. turntable loading [kg] D RA-120 with mechanical turntable D RA-120 with D.A.T. function D RA-120P with mechanical turntable D RA-120P with D.A.T. function

46 Roundtest RA-1600 Specifications Turntable Rotational accuracy Rotational speed Max. probing Ø Max. workpiece Ø Max. turntable loading Centering range ±3 Leveling range ±1 Radial: (0,02+0,0006H)µm H: Measuring height from turntable surface () Axial: (0,02+0,0006X)µm X: Radial distance from center () 4, 6, 10 rpm kg Series Form Measuring System This is a PC-compliant form measuring system which allows you to measure roundform geometry like cylindricity. The Roundtest RA-1600 offers the following benefits: It is equipped with a high accurate turntable accuracy of ( H)µm. You can carry out simple & accurate centering and leveling of the workpiece with D.A.T. (Digital Adjustment Table). The user friendly software, ROUNDPAK, gives you easy drag and drop usage. ROUNDPAK also has easy-to-use part prograing and single measurement functions. A remote control box is including allowing you easy operation. There is also an auto follow function for easy and quick pre-centering of the workpiece. Vertical column Max. probing height Max. probing depth Straightness Parallelism with turntable axis Software 300 above turntable surface 91 (minimum ID : ø32 ) 50 (minimum ID : ø7 ) 0,20 µm / 100 0,30 µm / 300 1,50 µm / 300 ROUNDPAK Measuring screen RA-1600 Spiral Measurement/Analysis (RA-1600) Provided with a spiral measurement function that combines turntable rotation and rectilinear motion allowing cylindricity, coaxiality and other form characteristics to be measured in continuous data stream mode. Result screen ROUNDPAK Measurement through X - axis tracking Measurement while tracing is possible through a built-in linear scale in the X - axis. 567

47 Roundtest RA-1600 Series Roundness Measuring System Additional Specifications Optional accessories Other optional and standard accessories are listed later in this section for accessories and styli. Optional accessories Description Three jaw chuck OD: 2-78, ID: Micro-chuck OD: 1-1, Quick chuck OD: 1-79, ID: Magnification checking gauge Collet chuck OD: 0, AAL019 Side table 12AAL090 Sliding detector holder 12AAF203 Double length detector holder 12AAF204 Large diameter detector holder 12AAK110 Vibration isolator 12AAK120 Monitor arm Auxiliary stage for a low-height workpiece Gauge block set for calibration Dimensions Max. workpiece ø Max. probing Ø Max. turntable loading Description [kg] D RA AAF203 12AAF

48 Roundtest RA-2200 Specifications Turntable Rotational accuracy Rotational speed Max. probing Ø Max. workpiece Ø Max. turntable loading Centering range Leveling range ±1 Vertical column Max. probing height Max. probing depth Straightness Parallelism with rotation center Radial: (0,02+0,00035H)µm H: Measuring height from turntable surface () Axial: (0,02+0,00035X)µm X: Radial distance from center () 2, 4, 6, 10 rpm kg DS / DH: ±5 AS / AH: ±3 AS / DS : 300 AH / DH: 500 above turntable surface 85 (minimum ID : ø32 ) 50 (minimum ID : ø7 ) AS / DS : 0,10 µm / 100 AS / DS : 0,15µm / 300 AH / DH: 0,25 µm / 500 AS / DS : 0,7 µm / 300 AH / DH: 1,2µm / 500 Series Form Measuring Instrument This is a highly accurate form measuring system which allows you to measure roundform geometry like cylindricity. The Roundtest RA-2200 offers the following benefits: It has fully motorised axes movement. Its extremely high turntable accuracy of ( H)µm gives you excellent form analysis. The user friendly software, ROUNDPAK, gives you easy drag and drop usage and a wide range of parameters. ROUNDPAK also has easy-to-use part prograing and single measurement functions. A huge number of styli provides you with maximum flexibility. There is an auto follow function for easy and quick pre-centering of the workpiece. There is a wide variety of models available to suit any application. RA-2200DS/DH: These models have a navigation function supplied as standard, to quickly and simply guides you through the centering and leveling task. The models are equipped with the D.A.T. (Digital Adjustment Table). RA-2200AS/AH: The models have an automatic centering and leveling turntable supplied as standard, freeing you from the centering and leveling task. The models are equipped with the A.A.T. (Automatic Adjustment Table). Horizontal axis Straightness Perpendicularity to rotation center Software 0,7 µm / µm / 150 ROUNDPAK FORMTRACEPAK-RA (optional for roughness detection unit) RA-2200 ROUNDPAK Simple to operate even with a full set of parameters and analysis functions. Automatic measurement 569

49 Roundtest RA-2200 Series Roundness/Cylindricity Measuring System Accessories and dimensions Additional Specifications Optional accessories Other optional and standard accessories are listed later in this section for accessories and styli. Optional accessories Description Price Three jaw chuck OD: 2-78, ID: Micro-chuck OD: 1-1, Quick chuck OD: 1-79, ID: Magnification checking gauge 12AAL019 Side table 12AAF203 Double length detector holder 12AAF204 Large diameter detector holder 12AAK110 Vibration isolator 12AAK120 Monitor arm Auxiliary stage for a lowheight workpiece 12AAF353 Roughness detection unit Detector 0,75 mn Model Centering/leveling adjustment 1* Vertical travel Max. workpiece ø Max. probing Ø Max. turntable loading [kg] D RA-2200AS AAT D RA-2200AH AAT D RA-2200DS DAT D RA-2200DH DAT * AAT : Automatic Adjustment Table DAT : Digital Adjustment Table 570

50 Roundtest RA-H5200 Specifications Turntable Rotational accuracy Rotational speed Max. probing Ø Max. workpiece Ø Max. turntable loading Centering range Leveling range ±1 Radial: (0,02+0,00035H)µm H: Measuring height from turntable surface () Axial: (0,02+0,00035X)µm X: Radial distance from center () 2, 4, 6, 10 rpm kg 80 kg without auto centering ±5 Series High-precision Form Measuring Instrument This is a highly accurate, precision form measuring system developed to give you the highest accuracy as well as high flexibility and analytical capability. The Roundtest RA-H5200 offers the following benefits: Its integrated vibration isolator helps you to measure within the best conditions. It has a high measuring range and loading mass. The user friendly software, ROUNDPAK, gives you easy drag and drop usage and a wide range of parameters. ROUNDPAK also has easy-to-use part prograing and single measurement functions. A.A.T. (Automatic Adjustment Table) gives you fully automatic centering and leveling. There is an auto follow function for easy and quick pre-centering of the workpiece. Vertical column Max. probing height Max. probing depth Straightness Parallelism with rotation center Horizontal axis Straightness Perpendicularity to rotation center Software AS : 350 AH: 550 above turntable surface 85 (minimum ID : ø32 ) 50 (minimum ID : ø7 ) AS / AH : 0,05 µm / 100 AS : 0,14µm / 350 AH : 0,20 µm / 550 AS : 0,20 µm / 350 AH : 0,32µm / 550 0,4 µm / 200 0,5 µm / 200 ROUNDPAK FORMTRACEPAK-RA (optional for roughness detection unit) Highly accurate, automatic centering/leveling turntable The performance of this turntable has been achieved through exceptional manufacturing accuracy of the critical components, in addition to a high-accuracy air-bearing that provides superior rigidity. The resulting rotational accuracy, the heart of a Roundtest measuring system, is world-class at H µm. ROUNDPAK Simple to operate even with a full set of parameters and analysis functions. Sliding detector-unit holder provided as a standard feature The detector-unit holder is equipped with a sliding mechanism, enabling one-touch measurement of a workpiece with a deep hole having a thick wall, which has been difficult with the conventional standard arm. Sliding distance :

51 Roundtest RA-H5200 Series 211 Dimensions and accessories Additional Specifications Optional accessories Other optional and standard accessories are listed later in this section for accessories and styli. Optional accessories Description Price Three jaw chuck OD: 2-78, ID: Micro-chuck OD: 1-1, Quick chuck OD: 1-79, ID: Magnification checking gauge 12AAL019 Side table 12AAF203 Double length detector holder 12AAF204 Large diameter detector holder 12AAF205 Triple length holder for extra-deep holes 12AAF353 Roughness detection unit Detector 0,75 mn Dimensions Model Centering/leveling adjustment 1* Vertical travel Max. workpiece ø Max. probing Ø Max. turntable loading [kg] D RA-H5200AS AAT D RA-H5200AH AAT * AAT : Automatic Adjustment Table AAF203 12AAF204 12AAF

52 Roundtest Extreme RA-2200CNC Specifications Rotational accuracy Radial: (0,02+0,00035H)µm H: Measuring height from turntable surface () Axial: (0,02+0,00035X)µm X: Radial distance from center () Rotational speed 2, 4, 6, 10 rpm Max. probing Ø 256 Max. workpiece Ø 580 Max. turntable 30 kg loading Centering range ±3 Leveling range ±1 Series High-precision Form Measuring Instrument This is a fully automatic CNC form measuring instrument that gives highly accurate results. The Roundtest Extreme RA-2200CNC offers you the following benefits: It has a CNC controlled measuring system with orientation steps of 1. The extremely high turntable accuracy of ( H)µm gives you highly accurate form analysis. The user friendly software, ROUNDPAK, gives you easy drag and drop usage and a wide range of parameters. ROUNDPAK also has easy-to-use part prograing and single measurement functions. An automatic centering and leveling turntable A.A.T. (Automatic Adjustment Table) is supplied as standard, freeing you from the centering and leveling task. Vertical column Max. probing height Max. probing depth Straightness Parallelism with rotation center Horizontal axis Straightness Perpendicularity to rotation center Software AS : 300 AH: 500 above turntable surface 104 (minimum ID : ø32 ) 26 (minimum ID : ø12,7 ) AS / AH : 0,10 µm / 100 AS : 0,15 µm / 300 AH : 0,25 µm / 500 AS : 0,70 µm / 300 AH : 1,20 µm / 500 0,7 µm / 150 1,0 µm / 150 ROUNDPAK FORMTRACEPAK-RA (optional for roughness detection unit) RA-2200 CNC + optional vibration isolator [12AAK110] and side table [12AAL019] Optional accessories 12AAL019 12AAK110 12AAK120 12AAG419 Description Side table Vibration isolator Monitor arm Roughness detection unit CNC ( 0,75mN ) ROUNDPAK Simple to operate even with a full set of parameters and analysis functions. Centering/leveling adjustment 1* Vertical travel Max. workpiece ø Model Max. probing Ø Max. turntable loading [kg] D AAT RA-2200CNC AS D AAT RA-2200CNC AH * AAT : Automatic Adjustment Table 573

53 Roundtest Extreme RA-H5200CNC Series High-precision Roundness/Cylindricity Measuring System This is a CNC form measuring instrument that combines high accuracy with automatic CNC measurements. The Roundtest Extreme RA-5200CNC offers you the following benefits: An integrated vibration isolator helps you to measure within best conditions. It will greatly improve your productivity and efficiency. You can take highly accurate, fast and operator-free measurements. The user friendly software, ROUNDPAK, gives you easy drag and drop usage and a wide range of parameters. ROUNDPAK also has easy-to-use part prograing and single measurement functions. An automatic centering and leveling turntable A.A.T. (Automatic Adjustment Table) is supplied as standard, freeing you from the centering and leveling task. Specifications Turntable Rotational accuracy Rotational speed Max. probing Ø Max. workpiece Ø Max. turntable loading Centering range Leveling range ±1 Radial: (0,02+0,00035H)µm H: Measuring height from turntable surface () Axial: (0,02+0,00035X)µm X: Radial distance from center () 2, 4, 6, 10 rpm Auto centering: 20 rpm kg 80 kg without auto centering ±5 Vertical column Max. probing height Max. probing depth Parallelism with rotation center Horizontal axis Straightness Perpendicularity to rotation center Software AS : 350 AH: 550 above turntable surface 104 (minimum ID : ø32 ) 26 (minimum ID : ø12,7 ) AS : 0,20 µm / 350 AH : 0,32 µm / 550 0,4 µm / 200 0,5 µm / 200 ROUNDPAK FORMTRACEPAK-RA (optional for roughness detection unit) RA-H5200CNC + side table [12AAL019] Additional Specifications Optional accessories Other optional and standard accessories are listed later in this section for accessories and styli. Optional accessories 12AAL019 12AAG419 Description Side table Roughness detection unit CNC ( 0,75mN ) Dimensions ROUNDPAK Simple to operate even with a full set of parameters Model Centering/leveling adjustment 1* Vertical travel Max. workpiece ø Max. probing Ø Max. turntable loading [kg] D RA-H5200CNC AS AAT D RA-H5200CNC AH AAT * AAT : Automatic Adjustment Table 574

54 Optional Styli for Roundtest Standard accessories Description 12AAL021 Stylus standard type Interchangeable styli for RA-10, RA-120, RA-120P, RA-1600, RA-2200, RA-H5200 Optional accessories Description 12AAL022 Stylus for notches 12AAL023 Stylus for deep grooves 12AAL024 Stylus for corner 12AAL025 Stylus for cutter marks 12AAL026 Stylus ø0,8 for small holes 12AAL027 Stylus ø1 for small holes 12AAL028 Stylus ø1,6 for small holes 12AAL029 Stylus ø0,5 for extra small holes 12AAL030 Stylus ø1,6 ball type 12AAL031 Stylus disc type 12AAL032 Stylus ø0,5 for cranks 12AAL033 Stylus ø1 for cranks 12AAL034 Stylus for flat surfaces 12AAL035 Stylus 2x-long standard type *¹ 12AAL036 Stylus 2X-long type for notches *¹ 12AAL037 Stylus 2X-long type for deep grooves *¹ 12AAL038 Stylus 2X-long type for corners *¹ 12AAL039 Stylus 2X-long type for cutter marks *¹ 12AAL040 Stylus 2X-long type ø1 for small holes *¹ 12AAL041 Stylus 3X-long standard type *¹ *² 12AAL042 Stylus 3X-long type for deep grooves *¹ *² 12AAL043 Stylus shank 12AAL044 Stylus shank for grooves 12AAL045 Stylus shank 2X-long type for grooves *¹ *1 Not available for RA-10, RA-120, RA-120P *2 Measuring is only possible in the vertical direction 12AAL021 - Standard ø 1,6 tungsten carbide 12AAL024 - Corner R 0,25 sapphire 12AAL027- Small hole ø 1 tungsten carbide 12AAL030- ø 1,6 ball ø 1,6 tungsten carbide 12AAL022 - Notch ø 3 tungsten carbide 12AAL025 - Cutter mark R 15 tungsten carbide 12AAL028 - Small hole ø 1,6 tungsten carbide 12AAL031- Disc ø 12 12AAL023 - Deep groove R 0,25 sapphire 12AAL026 - Small hole ø 0,8 tungsten carbide 12AAL029- Extra small hole ø 0,5 tungsten carbide 12AAL032- Crank ø 0,5 tungsten carbide 146 ø AAL033- Crank ø 1 tungsten carbide 12AAL034- Flat surface Tungsten carbide 12AAL035-2X-long standard ø 1,6 tungsten carbide Notches Flat surface 12AAL036-2X-long notch ø 3 tungsten carbide 12AAL037-2X-long deep groove R 0,25 sapphire 12AAL038-2X-long corner R 0,25 sapphire Cutter marks Corner 12AAL039-2X-long type cutter mark R 15 tungsten carbide 12AAL040-2X-long small hole ø 1 tungsten carbide 12AAL041-3X-long standard ø 1,6 tungsten carbide Small hole 12AAL042-3X-long deep groove R 0,25 sapphire 12AAL043- Stylus shank for mounting M2 - CMM stylus 12AAL044- Stylus shank groove for mounting M2 - CMM stylus 12AAL045- Stylus shank 2X groove for mounting M2 - CMM stylus 575

55 Optional Styli for Roundtest Interchangeable styli for RA-2200CNC, RA-H5200CNC ø ø AAE301 - Standard ø 1,6 tungsten carbide ø ø AAE302 - Flat surface ø 1,6 tungsten carbide ø ø1.2 12AAE303 - ø 1,6 ball ø 1,6 tungsten carbide ø Standard accessories 12AAE301 12AAE302 Optional accessories Description Stylus standard type for CNC Stylus for flat surfaces for CNC Description Price 12AAE303 Stylus ball ø1,6 for CNC AAE304 Stylus ball ø0,8 for CNC AAE305 Stylus ball ø0,5 for CNC AAE306 Stylus for deep holes for CNC AAE307 Stylus for deep holes for CNC AAE308 Stylus for deep grooves for CNC 12AAE309 Stylus for notches for CNC AAE310 Stylus for grooves for CNC AAE304 - ø 0,8 ball ø 0,8 tungsten carbide 12AAE305 - ø 0,5 ball ø 0,5 tungsten carbide 12AAE306 - Deep hole ø 1,6 tungsten carbide (69.6) 58 ø ø1.2 12AAE307 - Deep hole ø 1,6 tungsten carbide 12AAE308 - Deep groove ø 1,6 tungsten carbide 12AAE309 - Notch ø 3 tungsten carbide AAE310 - Groove ø 1,6 tungsten carbide 576

56 Optional Accessories for Roundtest Optional accessories for Roundtest and Roundtest Extreme Auxiliary stage for a low-height workpiece Description Used for measuring a workpiece whose diameter is 40 or less and whose height is 20 or less Chuck - Quick chuck This Chuck is useful when measuring small workpieces. You can easily clamp them with its knurled ring. Holding capacity External dimensions Internal jaw: ID = ø External jaw: OD = ø 1-79 ø118 x Internal jaw: ø 0,1-1,5 ø 107 x 48, Chuck - Three jaw chuck (key operated) Holding capacity External dimensions Internal jaw: ID = ø Internal jaw: OD = ø 2-35 External jaw: OD = ø ø157 x 70,6 Cylindric square Cylindricity Roundness Squareness Straightness [µm] [µm] [µm] [µm] , Gauge block set for calibration Description Standard accessory for RA-2200,RA-2200CNC Standard accessory for RA-H5200 and RA-H5200CNC Magnification checking gauge Max. calibration range Graduation [µm] [µm] , Origin point gauge Description Standard accessory for RA-1600, RA-2200 and RA-H Vibrator isolator and accessories Vibration isolation method External dimensions Description Air suspension (WxDxH) Diaphragm isolation system 750x550x59 For RA-2200 and RA-2200CNC Stand for RA-2200 and RA-2200CNC 12AAL x 670 x 700 Side table 12AAK x 800 x 700 Vibration isolator 12AAK120 Monitor arm 12AAK AAK120 12AAK AAL