Wire Wound Chip Inductor Low Profile Type LWL LWL1008. Features. Applications

Size: px

Start display at page:

Download "Wire Wound Chip Inductor Low Profile Type LWL LWL1008. Features. Applications"

Clemence Simon
6 years ago
Views:

1 Wire Wound Chip Inductor Low Profile Type Wire Wound Chip Inductor Low Profile Type Features Ceramic base provides high SRF Ultra-compact inductors provide high Q factors Miniature SMD chip inductor for fully automated assembly Outstanding endurance from pull-up force, mechanical shock and pressure Tight tolerance down to +/- 2% RoHS Compliant Applications RF products: Cellular Phone (CDMA/GSM/PHS) Cordless Phone (DECT/CT1CT2) Remote Control, Security System Wireless PDA WILL, Wireless LAN/ Mouse/ Keyboard/ Earphone VCO, RF Module & Other Wireless Products Base Station, Repeater GPS Receiver Broad Band Applications: CATV Filter, Tuner Cable Modem/ XDSL Tuner Set Top Box IT Applications: USB 2.0 IEEE 1394 TAITRON COMPONENTS INCORPORATED Tel: (800)-TAITRON (800) (661) Fax: (800)-TAITFAX (800) (661) Page 1 of 9

2 Constructions and Dimensions Wire Wound Chip Inductor Low Profile Type Item Material Ceramic Core Magnet Wire Electrode (Ag/Pd+Ni+Sn) UV Glue Teminal Wraparound: Approx /0.18mm on both ends Unit=mm Type Size In Inch A Max. B Max. C Max. D Ref. E F G H I J LWL LWL Page 2 of 9

3 Electrical Specifications LWL0805 Type: Inductance (nh) Tolerance (%) L Freq. (MHz) Quality Factor Min. SRF Min. (GHz) DCR Max. (Ω) IDC Max. (ma) 1.8 ±5% / 1500MHz ±5, 10% / 1000MHz ±5, 10% / 1000MHz ±5, 10% / 1500MHz ±5, 10% / 1000MHz ±2, 5, 10% / 750MHz ±2, 5, 10% / 750MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 250MHz ±2, 5, 10% / 250MHz ±2, 5, 10% / 50MHz Page 3 of 9

4 LWL1008 Type: Inductance (nh) Tolerance (%) L Freq. (MHz) Quality Factor Min. SRF Min. (GHz) DCR Max. (Ω) IDC Max. (ma) 3.3 ±5, 10% / 1500MHz ±5, 10% / 500MHz ±5, 10% / 1500MHz ±5, 10% / 1500MHz ±5, 10% / 500MHz ±5, 10% / 350MHz ±5, 10% / 500MHz ±5, 10% / 350MHz ±5, 10% / 500MHz ±5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 500MHz ±2, 5, 10% / 350MHz ±2, 5, 10% / 100MHz Page 4 of 9

5 Environment Characteristics Electrical Performance Test Test Item Test Method Requirement Inductance Q Value SRF DC Resistance RDC Rated Current IDC Over Load Withstanding Voltage HP4286 HP4286 HP4287 Micro-Ohm meter (Gom-801G) Applied the current to coils, The inductance change should be less than 10% to initial value. Applied 2 times of rated allowed DC current to inductor for a period of 5 minutes AC voltage of 500 VAC applied between inductor terminals and case for 1 min. Refer to standard electrical characteristic spec. Inductors shall have no evidence of electrical and mechanical damage Inductors shall have no evidence of electrical and mechanical damage Insulation Resistance 100 V DC applied between inductor terminal and case 1000M ohm min. Mechanical Performance Test Test Item Test Method Requirement Vibration Resistance to Soldering Heat Component Adhesion (Push Test) Drop Solderability Test device shall be soldered on the substrate Oscillation Frequency: 10 to 55 to 10Hz for 1 min. Amplitude: 1.5mm Time: 2 hrs for each axis (X, Y & Z), total 6 hrs Solder Temperature: 270±5C Immersion Time: 10±2 seconds The device should be soldered (260±5 for 10 seconds) to a tinned copper substrate. A dynamiter force gauge should be applied to the side of the component. The device must withstand a minimum force of 2 or 4 pounds without a failure of adhesion on termination Dropping chip by each side and each corner. Drop 10 times in total Drop height: 100 cm Drop weight: 125 g Inductor shall be dipped in a melted solder bath at 245 ±5 for 3 seconds Appearance :No damage L change: within ±5% Q change: within ±10% 3 lbs. No damage 90% covered with solder Resistance to Solvent MIL-STD202F, Method 215D No damage on appearance and marking Page 5 of 9

6 Climatic Test Test Item Test Method Requirement Temperature Characteristic Humidity Low Temperature Storage Thermal Shock -40~+125 C Temperature: 40±2 C Relative Humidity: 90~95% Time: 96±2 hrs Measured after exposure in the room condition for 2 hrs Temperature: -40±2 C Time: 96±2 hrs Inductors are tested after 1 hour at room temperature One cycle: Step Temperature( C ) Time(min.) 1-25± ± ± ±2 15 Total: 5 cycles Appearance: No damage L change: within ±10% Q change: within ±20% High Temperature Storage High Temperature Load Life Damp Heat with Load Temperature: 125±2 C Time: 96±2 hrs Measured after exposure in the room condition for 1hour Temperature: 85±2 C Time: 1000±12 hrs Load: Allowed DC current Temperature: 40±2 C Relative Humidity: 90~95% Time: 1000±12 hrs Load: Allowed DC current Storage Temperature: 25±3 C; Humidity < 80%RH There should be no evidence of short or open circuit. Page 6 of 9

Packing Information: Reel Specifications Unit: mm Type A B C W T LWL0805 178.0 ± 2.0 60 ± 0.5 13.0 ± 0.3 9.0 ± 0.3 11.4 ± 1.

0 Embossed Plastic Tape Specifications and Packaging Quantity Type A B C D E F G H I Unit: mm LWL0805 8 ± 0.2 1.80 ±0.

7 Packing Information: Reel Specifications Unit: mm Type A B C W T LWL ± ± ± ± ± 1.0 LWL ± ± ± ± ± 1.0 Embossed Plastic Tape Specifications and Packaging Quantity Type A B C D E F G H I Unit: mm LWL ± ±0.1 4 ± ± ± ±0.1 2 ± ± ± LWL ± ±0.1 4 ± ± ± ±0.1 2 ± ± ± Reel (EA) Page 7 of 9

8 How to Order LWL 0805 T 3N9 J- xx -TR70 Packing Code TR70:7 Reel, RoHS Factory Location Code Tolerance Code: G: ±2%; J: ±5%; K: ±10%; Inductance Code: 3N9:3.9nH; 27N: 27nH R10:100nH; 1R0: 1000nH T: Material Code Size Code in inch(mm) 0805(2012); 1008(2520); Taitron Wire Wound Chip Inductor - Low Profile Type Page 8 of 9

9 How to contact us US HEADQUARTERS WEST HARRISON PARKWAY, VALENCIA, CA Tel: (800)-TAITRON (800) (661) Fax: (800)-TAITFAX (800) (661) TAITRON COMPONENTS MEXICO, S.A.DE C.V. BOULEVARD CENTRAL 5000 INTERIOR 5 PARQUE INDUSTRIAL ATITALAQUIA, HIDALGO C.P MEXICO Tel: Fax: TAITRON COMPONENTS INCORPORATED TAIWAN, TAIPEI 6F., No.190, Sec. 2, Zhongxing Rd., Xindian Dist., New Taipei City 23146, Taiwan R.O.C. Tel: Fax: TAITRON COMPONENT TECHNOLOGY, SHANGHAI CORPORATION METROBANK PLAZA,1160 WEST YAN AN ROAD, SUITE 1503, SHANGHAI,200052, CHINA Tel: Fax: CROSS REGION PLAZA, 899 LINGLING ROAD, SUITE 18C, SHANGHAI, , CHINA Page 9 of 9

Wire Wound Chip Inductor

Wire Wound Chip Inductor Features Ceramic base provide high Ultra-compact inductors provide high Q factors ow profile, high current options Miniature SMD chip inductor for fully automated assembly Outstanding endurance from Pull-up