Assembly Instruction

Transcription

1 Assembly nstruction TWN - FU BUNK BED TWN - FU BUNK BED HARDWARE ST NO 80mm Bolt 22 pcs 6 60mm Bolt 0 pcs mm Bolt 2 pcs mm Screw 6 pcs 9 5 Allen Key M4 NO 2 DRAWNG onimmixce (8(88(n DESCRPTON 0 DESCRPTON DRAWNG -4iK*0 30mm Screw 50 pcs.0g00 6mm Screw 2 pcs (-(0 0 ) Wood Dowel 00 x 30mm 40 pcs Barrel Nut M6 x 3mm 32 pcs Metal Pin 09.5 x 27mm 4 pcs NOTE : A screwdriver will be needed to tighten all wood screws. Replacement Parts Request : Please advise part number from the above hardware list. MADE N MAAYSA TWN - FU BUNK BED ASSEMBY PAGE

2 Assembly nstruction TWN - FU BUNK BED MPORTANT: Unpack All Parts & Organize Before Assembly!!! TWN-FU BUNK BED COMPONENT ST PART A B DRAWNG DESCRPTON PART 3Z3 Headboard (Upper) K 333 Footboard (Upper) Headboard (lower) M Footboard (ower) :3:3: i C p onniimunq 3::3:3: D E F G H J ' : : DRAWNG.. Center Rail ;; (ower Front) (ower Rear) (Upper front) (Upper Rear) Guard Rail (Rear) 2 pcs O i iiiiiii. iiiiiiiiilir y ( p- T Guard Rail (Front) 2p pcs Guard Rail Support 3 pcs Slat (Upper) set Slat (ower) set adder eg (Upper-eft) adder eg (Upper-Right) adder eg ower (eft & Right) 2 pcs adder Stretcher (Upper & Middle) J i l Q DESORPTON 3 pcs adder Stretcher (ower) Support Panel MADE N MAAYSA TWN - FU BUNK BED ASSEMBY PAGE 2

3 Assembly nstruction TWN - FU BUNK BED nsert wood dowels, insert barrel nut into hole & insert bolt from outside. STEP _ \ - -, 8 Align bolts to connect with barrel nut & tighten. Cleaning nstructions : After assembly, clean & polish with a soft cloth. TWN - FU BUNK BED ASSEMBY PAGE 3

4 Assembly nstruction TWN - FU BUNK BED STEP 3 nsert bolts to connect with barrel nut & tighten. Remember to insert wood dowels also for alignment & strength. Cleaning nstructions : After assembly, clean & polish with a soft cloth. TWN - FU BUNK BED ASSEMBY PAGE 4

5 Assembly nstruction TWN - FU BUNK BED STEP 5 nsert metal pin, align & stack twin bed. CAUTON: Please be careful not to pinch your fingers. r STEP 6 nsert bolt to connect with barrel nut & tighten. Remember to insert wood dowel for alignment & strength. Cleaning nstructions : After assembly, clean & polish with a soft cloth. TWN - FU BUNK BED ASSEMBY PAGE 5

6 Assembly nstruction TWN - FU BUNK BED STEP 8 Please follow the pilot hole at right ladder rail. Cleaning nstructions : After assembly, clean & polish with a soft cloth. TWN - FU BUNK BED ASSEMBY PAGE 6

7 Assembly nstruction TWN - TWN BUNK BED SAFETY WARNNG Read all instructions carefully before assembling this product.. Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed. 2. Always use the recommended size mattress or mattress support, or both, to help prevent 3. the likelihood of entrapment or falls. Surface of mattress must be at least 5 in. (27 mm) below the upper edge of guardrails. 4. Do not allow children under 6 years of age to use the upper bunk. 5. Periodically check and ensure that the guardrail, ladder, and other components are in their proper position, free from damage, and that all connectors are tight. 6. Do not allow horseplay on or under the bed and prohibit jumping on the bed. 7. Prohibit more than one person on upper bunk. 8. Always use the ladder for entering and leaving the upper bunk. 9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts. 0. Use of a night light may provide added safety precaution for a child using the upper bunk.. Always use guardrails on both long sides of the upper bunk. f the bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and wall. 2. The use of water or sleep flotation mattresses is prohibited. 3. STRANGUATON HAZARD-Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited to hooks, belts and jump ropes. 4. Keep these instructions for future reference. SZE OF MATTRESS AND FOUNDATON: Use a mattress which is 37 2" " wide and 74"-75" long on upper bunk (twin size.) Ensure that the thickness of the mattress does not exceed 7" and that the mattress surface is at least 5" (27mm) below the upper edge of the guardrails. Use a mattress which is 38" wide and 75" long on lower bunk (twin size). Ensure that the thickness of the mattress is at least 7". WARNNG: Adult Assembly Required. This package contains small parts. Keep away from children. Replacement Parts: MPORTANT: A CONNECTONS MUST BE TGHTENED PROPERY