Hiddenbed ASSEMBLY INSTRUCTIONS. MODEL DOUBLE DECKER
|
|
- Leonard Crawford
- 6 years ago
- Views:
Transcription
1 ASSEMBLY INSTRUCTIONS MODEL DOUBLE DECKER
2 CONGRATULATIONS! YOU ARE A PROUD OWNER OF HIDDENBED The ultimate furniture that Doubles your Space Please read carefully the Assembly Instructions. Should you have any questions please contact our authorized dealer: For further information please check 3
3 Follow these simple steps to assemble your 2 Assemble the 3 main parts Put them together 3 Put the mattress in its place. LOOK, YOUR HIDDENBED IS READY! 4
4 MAIN PARTS &CARPENTRY LIST BODY PARTS COMPONENTS a+b 2a+2b + 2 BED PARTS COMPONENTS + DESK PARTS COMPONENTS 5
5 TO OBTAIN A SAFE A RELIABLE PERFORMANCE Make sure that: Side pannels bears on the floor at the same level. A carpet can be placed beneath both said adjacent bearing sides, but not place carpet or any shim beneath on side desk or body side alone. Stand at the middle of the furniture to make the transformation. Use a mattress of... of a maximum height of 0 inches. Total weight added on the moving parts, best around 40 lb. Avoid excessive or too asymmetric loads on desk. While lowering, please verify that bed bottom does not touch things left on the desk.things left on the desk canot exceed inches height. Next to the rear of the desk there is less height available. As with a door or a rocking chair, take good care not to trap fingers between closing parts. If power or signal cables are to be installed, consult a qualified person. If the bed does not stay down by it, add more weight on the desk. if the situation continues have the position point of action changed to a lower strength position. Remember a force equivalent to lift a CRT monitor is needed to transform the bed into desk. Ask your retailer for more details. 6 WARNINGS (!)Like a sliding door or a car door or a bike, you have to do certain things to enjoy Safely and reliably. Pay attention to theses recommendations!
6 MECHANISM KIT BOX A A A2 A3 A4 A5 A6 A7 MECH ARM PLATE 2 Pcs GAS SPRING 00N/300N 2 Pcs LOWER SUPPORT 2 Pcs LOWER SUPPORT PIN 2 Pcs A A9 A0 A COTTER PIN 2 Pcs BEARER 2 Pcs LINK PIVOT 2 Sets ADITIONAL SAFETY DEVICE TRUNNION BUSHING & SCREW 2 Sets LOCK 2 Pcs HARDWARE KIT LOCK BUSHING 4 Pcs PIN BALL 2 Pcs SAFETY BRACKET HAFELE Pcs Confirmat, H2, 7x70 Confirmat, H2, 7x50 Screw, Ph head,h0, 4.5x45 Screw, Ph head, H4, 4.5x35 Screw, Ph head, H20, 4.5x30 Screw, Ph head, H9, 4.5x20 Screw, Ph head, H3, 3.5x40 Screw, Ph head, H4, 3.5x6 Flat Head Allen & bushing, H6, 6x60 Dowell, 0x30 Bolt & nut, H3,/4 x /4 Wood plug, WP EXTRA TOOLS (not supplied) T T2 T3 M4 L - KEY Pc M5 L - KEY Pc Antiwear lubricant. M0 L - KEY Pc Extra tools needed: Phillips Head Screwdriver to put screw (H0, H4, H20, H9, H3, H4) and bend cotter pins. 7
7 BODY ASSEMBLY Arm pin outer position for more load on table Arm pin inner position for less load on table RIGHT SIDE SHOWN Do the same with left side symmetrically Attach the Gas Spring end to pin ball (A). 2 Attach the Gas Spring (A2) to lower suport (A3) using Lower Support Pin(A4), insert cotter pin (A5) and bend ends. Cotter pin 3 Attach plate (A) to body side (). Make sure the hook on the arms is facing upwards. 4 Attach lower Support (A3) to Body () but do not overtighten. A3 4 3 H3 A H3 H3 A2
8 5 6 H0 4 H0 6 5 Attach Bunk Bed Slat Cleat (6) to Bunk Bed Side (4) and Body Back (5) using screw H H2 4 2 Attach Body Sides () to Bottom Strectcher (2), Bunk Bed Side (4)and Body Back (5) fixed using dowels and screws H Attach Shelf Stretcher () to Shelf (0) using screws H4. H4 Attach Shelf to Body Back and screws H0, also attach Shelf to Body Side using screws H2. 0 9
9 Attach Bed Slats (5) to Bunk Bed Slats cleats using screws H0. 5 Attach Guard Rails (7 y ) to Bunk Bed Side and Body Back using screws H
10 DESK ASSEMBLY Attach Desk Back (9) to Desk Top (7) with Screws H2. H Screw Wood Plugs (WP) to inner side of Desk Sides(). H4 WP 3 Attach one of the Desk Sides() to the Desk Top(7) using dowels and screws H2. Then insert Wood Plug into the Desk Stiffener. 7 H2
11 4 Attach the other Desk Side to the Desk Top using dowels and screws H2 and inserting the Wood Plug into the Desk Stiffener. 7 H2 5 Attach Tube Cover() to Desk Top(7) using screws H H3 6 Attach the Tribearer(A6) to the Desk Sides() using screw H6, H2 and H9. H2 H9 2 H6 H2
12 Insert locks into the Desk Sides. BED ASSEMBLY Attach Front Rail (0) and Rear Rail () to Bed Heads () with dowels and screws (H2). Be careful, put cleats inside. Perforations for Slats should be pointing bed up. (Down in sketch position!!) 0 H2 Slats and salt cover must be attached to the bed after the bed was attached to the body side. 3
13 FINAL ASSEMBLY Assemble two Links Pivot Sets attaching three link Bushings to one triangle plate (outer cones to bushing) using Link Screws. 2 Put bed heads bearing on desk sides carefully, aligning holes (see detail in sketch STEP 2) provided for Link bushings. In both sides in turn, place place from outside the Link Pivot Set into link holes as shown. Slighty displacing or rising the bed as required to push the Link in place. SLIGHTLY HEAVY - BE CAREFUL Fix the remaining Triangle plates (A7) with Link Screws to Link Pivot. Tighten screws, re-check tightening all screws. 4
14 4 Slide Body carefully in order to align plates with bed head holes. Then standing at rear side of Body, introduce Trunnion Bushing (A) with screw. Screw in a few turns, and let loose. Repeat at the other side. Tighten screws (A) strongly. BODY 5 Attach from behind the bed s center slat (2) to the smaller bed cover (9a) with screw H4 with a few turns and let loose. These screws will be removed in step 7. Then attach the bed cover and the slat to the rear cleat with screw H0. H0 9a H0 2 2 H4 H0 0 6 Pull all screws (H0) through the Bed Slats (2) and through Narrow Bed Cover (9a) to Screw in Rear Rail Claet. 9a 5
15 7 From under the bed. Take out the screw of step 5. Between the Cleat of Front Rail (0) and Bed Slats (2), put edge of Wide Bed Cover (9b). Use one screw H4 to Fix Wide and Narrow Cover to one of the center slats. 9a 9b With the bed as shown in sketch pull all screws (H4) through the Bed Slats (2) and through Wide Bed Cover (9b) to screw in Front Rail Claet. H0 9 From under the bed. Pull screws H4 through the remaing holes fixing the narrow and wide covers with the slats. The wide cover must overlap the narrow. 6 H4
16 0 Attach Concealers to Body Sides Using screw H0. Wait until setp 0 is done to screw the bottom part of the concealers.. Place the plastic bushing (A0) in the concealer perforations for the locks. Lift the bed slowly, talking care of keeping the desk in horizontal position. Once in upper position, lock the bed by pushing in the Lock at both sides. 2 PUSH IN TO LOCK 3a 3b 3c CAUTION! - EXTRA STRENGHT REQUIRED We recommend to sit on the floor and pull strongly 2- TAKE CARE OF YOUR FINGERS Do not put fingers in the hook. Hold the arm as shown. 7
17 ASSEMBLY HAS FINISHED For Normal Use: Check that the floor is clear to lower the bed. Unlock to change from desk to bed position. Stand at the middle of the furniture to pull from bed beam and push down desk to make the transformation. The mechanism is already calibrated to work with the mattress on and a weight simiilar to 35/40 lbs. on the desk. If the bed doesn t stay down by itself, add more weight on the desk.
18 SAFETY PRECAUTIONS Use the lock placed at the desk side to safe use in bed and desk position. DESK POSITION BED POSITION PUSH IN TO LOCK PUSH IN TO LOCK Attach the s body to the wall using the brackets and proper wall anchors. A QUALIFIED PERSON SHOULD FIX THE HIDDENBED TO THE WALL. THE FLOOR (LEVELING AND RESISTANCE), THE WALL (LEVELING AND RESISTANCE) AND THE FIXING (SCREWS AND ANCHORS ACCORDING TO THE WALL MATERIAL) MUST BE VERIFIED IN ORDER TO GET A SECURE FIXATION. WALL NO PROPER FIXATION CAN CAUSE UNDESIRED MOVEMENT
Follow these steps to assemble your Hiddenbed 1 Construct the 3 main parts 2 Assemble them together 3 Add a mattress. YOUR HIDDENBED IS READY! 2
Mounting Instructions Item No.: 271.97.300 Hiddenbed Furniture parts supplied by the customer Follow these steps to assemble your Hiddenbed 1 Construct the 3 main parts 2 Assemble them together 3 Add a
More informationBIFOLD FUTON FRAME TRINITY ARM. Seat Rails and Slats x 1. *Note: Use 4pc of 100mm Bolts and 4pc of 60mm Bolts to attach the arms to the Stretchers.
1A Parts in this box. 2pc with extra holes 2pc with extra holes & plastic stoppers Arms x 2 Back Rails and Slats x 1 Full Size: Slat Supports x 6 3pc are longer for the Back deck Back Side Rails x 2 Seat
More informationModels CW and AW Installation Instructions
Models CW and AW Installation Instructions Please keep these instructions for future reference. Hiddenbed must be dis-assembled before moving. a product of WALLBEDS! MODELS AW and CW HIDDENBED COMPONENTS
More informationPlease Do Not Return Your Item to the Retailer
Please Do Not Return Your Item to the Retailer Thank you for your purchase of an Epic Furnishings item You should enjoy many years of trouble free, dependable use If for any reason you are missing parts,
More informationPRINCESS SINGLE BED WITH TRUNDLE
PRINCESS SINGLE BED WITH TRUNDLE If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale Club Please call our customer service number and have
More informationO-Sullivan King 4 Poster Bed O-Sullivan Queen 4 Poster Bed Parts and Hardware List
Parts and Hardware List A. Left Headboard Post 1 pc B. Right Headboard Post 1 pc C. Left Footboard Post 1 pc D. Right Footboard Post 1 pc E. Headboard Panel 1 pc F. Footboard Rail 1 pc. Spindles 4 pcs
More informationStrata. urniture. Mission Rim Instructions. Parts in the Arm Box: Parts in the Body Box:
1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationStuff-Your-Stuff Platform Bed (Twin and Full)
Stuff-Your-Stuff Platform Bed (Twin and Full) Pre-Assembly: Please read all instructions before beginning assembly. Assembly by two people is a must. Save all packing materials until assembly is complete
More informationThis instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.
This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams
More informationGinger Twin Full Bunk Bed
N&D 0809 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.! SAFETY WARNING Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from
More informationFlat Panel TV Cart Instruction Manual SKU: STAND-TV02D Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-tv02d
More informationBunk Pod Front Entry Assembly Instructions
Bunk Pod Front Entry Assembly Instructions www.podtime.co.uk enquiries@podtime.co.uk Working House Ltd How to assemble your pod This step by step guide will show how to assemble your pod(s) on site. It
More informationRiverside. Oakmont Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 1 pc. 1 pc. 20270 --5/0 Sleigh Headboard 20274 --5/0-6/6 Bed Rails 20273 -- 5/0 Storage Footboard, Panels, Slats Queen
More informationStrata. urniture. Addison Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 Back Panel x 1 with
More informationStrata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached Back Panel
More informationWhalen Furniture Mfg. Factory No. 5 Page # 1
If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale Club Please call our customer service number and have your instructions and parts list
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationL.L.Bean. Farmhouse Futon
L.L.Bean Farmhouse Futon Thank you for purchasing our Farmhouse Futon. Assembly of this product requires a Phillips Head Screwdriver and Flat Head Screwdriver. We have found it helpful to have a second
More informationBLUE ANT FURNITURE TITLE: FULL BUNKBED INSTRUCTIONS 10/10/09 DWG. NO. INSTR_888-FULL-BUNK SHEET 1 OF 9
BLUE ANT FURNITURE TITLE: FULL BUNKBED INSTRUCTIONS 10/10/09 DWG. NO. INSTR_888-FULL-BUNK SHEET 1 OF 9 WARNING: Failure to follow these warnings and assembly instructions could result in serious injury.
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationC70 Window Roller Repair Taken from: Heres the problem:
C70 Window Roller Repair Taken from: http://www.volvospeed.com/vs_forum/topic/115086-how-to-c70-window-rollers-permanent-fix/ Heres the problem: This happened to two separate window assemblys on my c70
More informationSAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20
SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management
More informationPantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or oth
88 5076 691 Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have taken great
More informationUSE STRAIGHT ALLEN WRENCH (Bz) WITH AN ELECTRIC SCREWDRIVER TO TIGHTEN SCREWS - NOTE: DO NOT OVER TIGHTEN
ASSEMBLY INSTRUCTIONS (VK) MODEL NO. 836-944P1 Made in Vietnam Thank you for purchasing this Powell product. We want to make sure it is complete and to your satisfaction. Please check all packing material
More informationProjector Ceiling Mount
INSTALLATION MANUAL Projector Ceiling Mount PID:3010 PID:5466 20kg (44lbs) RATED CAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! ISSUED: FEB. 2013 NOTE: Read the
More informationSteele TV Stand Stock # BH
LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
More informationWILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount
WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationRiverside. Windhaven Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 2 pcs. 4 pcs. 4 pcs. 4 pcs. 2 pcs. 5/0 Queen Storage Bed 50773 -- 5/0 Storage Footboard w/platform Note: The 50773 Storage Footboard can be used with the 50770 Panel Headboard
More informationShowpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV
Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV Installation and Assembly Instructions 2009 Incredible Technologies Inc. Version 0109 Showpiece Cabinet Integrated Stand for 32" - 52" LCD HDTV
More informationWARNING: Failure to follow these warnings and assembly instructions could
OXFORD BUNK BED TWIN OVER TWIN & FULL OVER FULL For Bunk Bed Twin Over Twin WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. To help prevent
More informationESA-300 Full Breakout
Interior View 0 Installation Instructions For use with ESA II Controler DORMA AUTOMATICS, Inc. 94 Sherwood Drive Toll-Free: 877-67-6 DL844-00 Lake Bluff, IL 60044 Fax: 877-4-7999 Rev. /07 Tools Required:
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationBEADBOARD LOFT BED ASSEMBLY INSTRUCTIONS
BEADBOARD LOFT BED ASSEMBLY INSTRCTIONS Date: 2013-Apr.-25 www.pbteen.com Page 1 of 10 ARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. To prevent
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationINSTRUCTION BOOKLET #C20
INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO
More informationAVA REGENCY BUNK BED TWIN OVER FULL
pottery barn kids AVA REGENCY BUNK BED TWIN OVER FULL www.potterybarnkids.com Date: 2016-Feb.-18 Page 1 of 14 WARNING: Failure to follow these warnings and assembly instructions could result in serious
More informationTM12 ASSEMBLY INSTRUCTIONS
TM12 ASSEMBLY INSTRUCTIONS Congratulations on purchasing the finest purple martin house available. Nature House Brand houses are the proven leader in aluminum martin housing for over half a century. After
More informationInteractive Monitor Arm
Interactive Monitor Arm Tools Required -5mm Allen wrench -Phillips screwdriver -Plastic mallet There are two ways to attach a Monitor Arm to a Full Frame; with a Beam, or with a Post Mount. Both methods
More informationFlat Panel Stand FPZ-655. for 32" to 55" Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold
FPZ-655 Flat Panel Stand for 32" to 55" Flat Panel Screens For a viewing experience that really stands out, Peerless FPZ-655 Universal Flat Panel Stand for 32" 55" flat panel TVs provides a brilliant combination
More informationLoft Bed Safety Warning
Loft Bed Safety Warning * Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove the warning label from bed. * Always use the recommended size
More informationPlease read these instructions before use and keep for future reference
Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly
More informationParts list Instruction guide Warnings Please read carefully before assembling and using product.
Parts list Instruction guide Warnings Please read carefully before assembling and using product. Jet Rail XL Part Number 27377 Tools required for assembly Hammer 9/16 Wrench 3/4 Wrench Ratchet 9/16 Socket
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS With Storage Headboard Installation Booklet 19 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE
More information4-Piece Table Tennis Table
Item# 45-6074 4-Piece Table Tennis Table Please keep this instruction manual for future reference If you have any problems with your new product, please contact Triumph Sports USA at 1-866-815-4173, or
More informationHardware and Components:
Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)
More informationLOWLINE SINGLE FOLD DOWN WALL BEDS
ASSEMBLY INSTRUCTIONS LOWLINE SINGLE FOLD DOWN WALL BEDS Tools Required For Assembly No 2 & No 4 Phillips Head Screwdrivers No 2 Slot Head Screwdriver Hammer Electric Drill (Hammer Drill for Masonry) 6.5mm
More informationCopyright 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
General Assembly Guidelines I. Insure that all parts and hardware are available before beginning assembly. II. III. IV. Follow each step carefully to insure the proper assembly of this product. Two people
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationASSEMBLY GUIDE. Mia Narrow Bookcase
ASSEMBLY GUIDE Mia Narrow Bookcase Components: Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase. Step
More informationVersion 1.1 TWO PEOPLE CODA BOOKCASE 10 SHELF REQUIRED.
Version 1.1 TWO PEOPLE CODA BOOKCASE 10 SHELF REQUIRED www.fantasticfurniture.com.au Enjoy Your purchase from Australia s Best Value Furniture Store www.fantasticfurniture.com.au PAGE 2 Assembly checklist
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationThanks for shopping with Improvements! Hamper Cabinet with Drawer Item #512188
Thanks for shopping with Improvements! Hamper Cabinet with Drawer Item #512188 IMPORTANT: Since the bin pivots forward, this unit must sit on the floor for safety reasons. Other items of the same width
More informationAssembly Instruction
Assembly nstruction TWN - FU BUNK BED TWN - FU BUNK BED HARDWARE ST NO 80mm Bolt 22 pcs 6 60mm Bolt 0 pcs 7 3 30mm Bolt 2 pcs 8 4 32mm Screw 6 pcs 9 5 Allen Key M4 NO 2 DRAWNG onimmixce (8(88(n DESCRPTON
More informationBefore Assembling the Storage Wall
Chapter 1 Assembling the Lista Storage Wall Lista provides two types of standard Storage Walls: B251 and B255. The design, construction, assembly, and quality are identical for both types, however, B251
More informationMETAL BLINDS. Deluxe GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE
METAL BLINDS Deluxe GETTING STARTED OPTIONAL HARDWARE A few simple tools are required: Steel Tape Measure Pencil Level Hold Down Brackets with Screws Extension Bracket Power Drill and Drill Bits Flathead
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationPERSONAL RECORD KEEPING
2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain
More informationProgeny Integrated Mobile Unit Unpacking/Assembly Guide
Summary: The following instruction will guide you through the unpacking and installation of the Progeny Mobile Unit. Any question or concerns or suggestions should be directed to Progeny Technical Support
More informationWALLBED Assembly Instructions
WALLBED Assembly Instructions 1 Congratulations and a Big Thank You for your purchase of a Wallbed Gallery Murphy Bed! We sincerely appreciate your business! First a few words of advice and caution: 1.
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationIMPORTANT! Recommended Tools. 7/16 Deep socket Phillips screwdriver
IMPORTANT! Read all instructions carefully before commencing any work. Always wear proper safety equipment. Some installation steps will require two or more installers. Recommended Tools Ratchet 10-mm
More informationWhalen Furniture Mfg. Inc. Factory No. 4 Page # 1
ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale
More informationStreamline L-Shaped Desk
www.teknikoffice.co.uk Teknik For all your newfangled gadgetry. Streamline L-Shaped Desk Model 5414417 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE
More informationStrata. urniture Watch our assembly videos at Denali Arms. Parts in the Arm Box: Hardware in this Box:
1A Denali Arms Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Hardware in this Box: (80mm) x 8 Barrel Nuts x 8 x 8 Wood Buttons x
More informationAll Restoration Hardware bunk beds are designed to meet the highest safety standards and comply with all U.S. and Canadian Bunk Bed regulations.
All Restoration Hardware bunk beds are designed to meet the highest safety standards and comply with all U.S. and Canadian Bunk Bed regulations. Page 1 of 13 Assembly Instructions Callum Storage Twin Bunk
More informationThis procedure will cover the steps to properly pack up the ARES for shipment.
TA Instruments Packing the ARES Instrument This procedure will cover the steps to properly pack up the ARES for shipment. Packing Materials Provided: Standard LS Shipping carton Shipping carton Shelf for
More informationWILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard
WILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard INSTRUCTION BOOKLET #13 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS
More informationWARNING: Read all instructions before assembling this product. KEEP INSTRUCTIONS FOR FUTURE USE
MARCELINE TWIN OVER TWIN BUNK BED INSTRUCTIONS Distributed in the U.S.A by: Restoration Hardware Baby & Child 11640 Harrel St. Suite B Mira Loma, California 91752 rhbabyandchild.com Distributed in Canada
More informationShelf Converter Drawer System
Shelf Converter Drawer System Installation and Use Instructions IF THIS PRODUCT IS INSTALLED IN A UNIT THAT DOES NOT MEET THE MINIMUM SYSTEM REQUIREMENTS, INJURY COULD RESULT. (SEE PAGE 2) Shelf Converter
More informationWhite Black Espresso Corner Desk Assembly Instructions
White Black Espresso Corner Desk Assembly Instructions Page 1 White / Black / Espresso Corner Desk Parts List Please check packaging for all parts and hardware before discarding. Unpack and lay parts on
More informationVersion 1.0 TWO PEOPLE COMO. Bed Head Double REQUIRED.
Version 1.0 TWO PEOPLE COMO Bed Head Double REQUIRED www.fantasticfurniture.com.au Enjoy Your purchase from Australia s Best Value Furniture Store www.fantasticfurniture.com.au PAGE 2 Assembly checklist
More informationFOR WALL MOUNT WORKSTATION
INSTALLATION MANUAL FOR WALL MOUNT WORKSTATION Weight Capacity 5-20 lbs. 1210180 Rev. C TABLE OF CONTENTS Tools Required / Installation Warnings / Disclaimer / Safety Warning / Adjustment Notification...3
More informationMantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before
More informationInstallation and Assembly: 32" - 60" Flat Panel TV Cart
nstallation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1M, SR560M R This product is UL Listed. t must be installed by a qualified professional installer. Max UL Load Capacity: 150 lb (68 kg)
More informationBarnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratch
88 5516 653 Barnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have
More informationRiverside. Harbor Hill Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 3 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 2 pcs. 8 pcs. 1 pc. 25770 -- 4/6-5/0 Panel Headboard (NOTE: the 25775 Leather
More informationAssembly Instructions
Assembly Instructions Frame Models Lotz (10000), Madison (2644), Vancouver (2710), Boston (2715), San Juan (2717), Marlowe (2719), Arlington (2722), Monticello (2730), Avalon (2750) & Tucson (2770) Tel:
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationINSTALLATION MANUAL. All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin
INSTALLATION MANUAL All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin TABLE OF CONTENTS GENERAL INFORMATION AND ADVISORIES 3 USPS INSTALLATION
More informationStar Trac Turbo Trainer Assembly & Setup
Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is
More informationColonial Classic Bar
88 5528 991 Colonial Classic Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts.
More informationInstallation Instructions
by Plato Woodwork Installation Instructions Plato Woodwork, Inc. 200 Third Street SW P.O. Box 98 Plato, MN 55370 www.platowoodwork.com 800.328.5924 SECTION GUIDE GETTING STARTED PAGE # Installation Methods...
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationWallboard or plastic Pre-drill holes and use hollow wall anchors or toggle bolts to install your shade in wallboard or plastic.
Woven Wood Shades Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Congratulations on purchasing Woven Wood Shades from Blindster. This window
More informationLifeGear G1 /HOME GYM ITEM NO.: 63100
LifeGear G1 /HOME GYM ITEM NO.: 63100 OWNER S MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain this owner s manual for future reference. The specifications of this product
More informationFOR PROFESSIONAL GARAGE DOOR INSTALLERS
Composite Garage Doors Installation Instructions FOR PROFESSIONAL GARAGE DOOR INSTALLERS Tools required Screwdriver Claw Hammer Locking Pliers Power Drill Level with a 3/32" Drill Bit Utility Knife 9/16",
More informationWallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS
Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note
More informationSmall Flat Panel Height-Adjustable Dual Swing Arm Wall Mount With Universal Slat Wall Mount (MSP-JS-KWG-110)
INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable Dual Swing Arm Wall Mount With Universal Slat Wall Mount () The dual swing arm desk mount is a sleek design providing a broad range of viewing
More informationPlease read and understand the OnBoard Timpani Cart Owner s Manual before using the Timpani Cart.
Assembly and Owner s Manual OnBoard Timpani Cart Performance Position Towing Position CONTENTS Important User Information...........................2 General......................................2 Manufacturer.................................2
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationRiverside. Harbor Hill King Storage Bed Assembly Instructions
King Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 6 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 2 pcs. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 25780 -- 6/0-6/6 Panel Headboard (NOTE: the 25785 Leather Headboard
More informationOperating, Servicing, and Safety Manual Model " Foot Shear CAUTION: Read and Understand
Operating, Servicing, and Safety Manual Model 3000 52" Foot Shear CAUTION: Read and Understand These Operating, Servicing, and Safety Instructions, Before Using This Machine. SAFETY The purpose of the
More information