Streamline L-Shaped Desk

Size: px

Start display at page:

Download "Streamline L-Shaped Desk"

Esmond Floyd
5 years ago
Views:

1 Teknik For all your newfangled gadgetry. Streamline L-Shaped Desk Model NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

2 Table of Contents Assembly Tools Required Part Identifi cation Hardware Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Assembly Steps 5-22 Hammer Not actual size Safety Warranty Skip the power trip. This time. Part Identifi cation While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. A LOWER END (1) B HUTCH END (2) C UPRIGHT (1) D CENTER UPRIGHT (1) E HUTCH UPRIGHT (2) F2 LOWER TOP (1) G HUTCH TOP (1) H2 TOP (1) I HUTCH BOTTOM (1) J SHELF (1) K BOTTOM (1) L DESK BACK (1) M LOWER BACK (1) N HUTCH BACK (1) O FLIP DOWN DOOR (1) P DRAWER FRONT (1) Q DRAWER BACK (1) R RIGHT DRAWER SIDE (1) S LEFT DRAWER SIDE (1) T DRAWER BOTTOM (1) U DIVIDER (1) V DESK FRAME (2) W RETURN FRAME (2) X UPPER MOLDING (1) Y LOWER MOLDING (1) Page 2

3 Part Identifi cation Now you know our ABCs. B G N E V I E H2 X M B L D O U C F2 Y A S Q T P R V W W J K Page 3

4 Hardware Identifi cation Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) 35MA EXTENSION RAIL MC EXTENSION SLIDE - 2 1F HIDDEN CAM F CAM DOWEL H PIVOT HINGE - 6 2I MAGNETIC CATCH - 1 6I STRIKE PLATE - 1 9I WASHER K PULL - 1 1N NAIL R METAL PIN - 4 1S BLACK 9/16" LARGE HEAD SCREW S BLACK 1-7/8" FLAT HEAD SCREW S GOLD 5/16" FLAT HEAD SCREW S BLACK 1/2" FLAT HEAD SCREW S BLACK 3/4" PAN HEAD SCREW S BLACK 3/4" PAN HEAD SCREW (with flat end) - 2 Page 4

5 Step 1 Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Push nineteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHTS (C and D), LOWER TOP (F2), DESK BACK (L), and DRAWER SIDES (R and S). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. F2 Meet Part (F2). This component has been engineered to be lighter, stronger, faster well ok. Not technically faster. But defi nitely makes for a sturdier L Desk that s easier to assemble and friendlier to the environment. L D C R S A B B Arrow Arrow 1F 2F (19 used) Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Page 5

6 Step 2 Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as shown in the upper diagram below. Be prepared, the parts are greasy. Fasten the EXTENSION RAILS (35MA) to the LOWER END (A) and CENTER UPRIGHT (D). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END and UPRIGHT. Turn a SCREW into this hole. Remember: Righty tighty. Lefty loosey. 35MC 35MA Push the black lever in and pull the SLIDE from the RAIL. Open end 1 2 Finished edge D 3 Surface without HIDDEN CAMS Surface with HIDDEN CAMS A 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Open end Finished edge Page 6

7 Step 3 Fasten the HUTCH ENDS (B) to the HUTCH TOP (G). Tighten four HIDDEN CAMS. Surface with HIDDEN CAMS Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. B Surface with HIDDEN CAMS G Surface with holes B Long fi nished edge Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Start Arrow Tighten Maximum 210 degrees Minimum 190 degrees Arrow Page 7

8 Step 4 Fasten the HUTCH UPRIGHTS (E) to the HUTCH BOTTOM (I). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). NOTE: You should start each SCREW a few turns before completely tightening any of them. Fasten the HUTCH BOTTOM (I) to the HUTCH ENDS (B). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S BLACK 1-7/8" FLAT HEAD SCREW (8 used in this step) I Surface with more holes B E Finished edge E Edge with holes B Finished edge Long fi nished edge Page

9 Step 5 Carefully turn your unit over onto its front edges. Lay the HUTCH BACK (N) over your unit. Make equal margins along all four edges of the HUTCH BACK (N). Push on opposite corners of your unit if needed to make it "square". Fasten the HUTCH BACK (N) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NAIL (28 used in this step) 1N N Page 9

10 Step 6 Carefully turn your unit over onto its back. Fasten the DESK FRAMES (V) to the HUTCH BOTTOM (I). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: The UPPER MOLDING (X) will have more holes than the LOWER MOLDING (Y). Do not confuse these MOLDINGS. Fasten the UPPER MOLDING (X) to the HUTCH BOTTOM (I). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 1S BLACK 9/16" LARGE HEAD SCREW (8 used in this step) Long edge X I The UPPER MOLDING (X) will have more holes than the LOWER MOLDING (Y). V V Page 10

11 Step 7 Fasten the LOWER TOP (F2) to the LOWER BACK (M). Tighten four HIDDEN CAMS. Fasten the LOWER TOP (F2) to the DESK FRAMES (V). Use six BLACK 3/4" PAN HEAD SCREWS (85S). Maximum 210 degrees Minimum 190 degrees Arrow F2 Surface with HIDDEN CAMS M Surface with more holes This hole should be here. F2 Surface with HIDDEN CAMS M V 85S V BLACK 3/4" PAN HEAD SCREW (6 used in this step) Page 11

12 Step 8 Fasten the UPRIGHT (C) to the TOP (H2). Tighten two HIDDEN CAMS. Push the MAGNETIC CATCH (2I) into the hole on the TOP (H2). Don't worry. It isn't Rome. This can be built in a day. Large hole 2I C These holes should be here. Surface with HIDDEN CAMS H2 Surface with holes Maximum 210 degrees Arrow Minimum 190 degrees Part (H2). Another sturdier, easier, friendlier component! Page 12

13 Step 9 Insert four METAL PINS (1R) into the DIVIDER (U). Insert the METAL PINS (1R) in one end of the DIVIDER (U) into the holes in the UPRIGHT (C). Maximum 210 degrees Arrow Fasten the CENTER UPRIGHT (D) to the TOP (H2). Tighten two HIDDEN CAMS. Minimum 190 degrees NOTE: Be sure the METAL PINS in the DIVIDER insert into the holes in the CENTER UPRIGHT. Finished edge C Surface without HIDDEN CAMS U D H2 1R Finished edge Page 13

14 Step 10 Fasten the LOWER END (A) and DESK BACK (L) to the TOP (H2). Tighten fi ve HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Surface with HIDDEN CAMS A Finished edge L Surface with HIDDEN CAMS H2 EXTENSION RAIL HIDDEN CAM If needed, loosen this SCREW and slightly raise the EXTENSION RAIL to tighten the HIDDEN CAM. Tighten the SCREW when fi nished. Page 14

15 Step 11 Fasten the BOTTOM (K) to a RETURN FRAME (W). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). 1st - Insert a PIVOT HINGE (15H) into the lower center hole in the RETURN FRAME (W). Fasten the SHELF (J) to the PIVOT HINGE in the RETURN FRAME. Use a BLACK 9/16" LARGE HEAD SCREW (1S). 2nd - Then, insert a PIVOT HINGE (15H) into the upper center hole in the RETURN FRAME (W). Fasten the SHELF (J) to the PIVOT HINGE in the RETURN FRAME. Use a BLACK 9/16" LARGE HEAD SCREW (1S). 1S BLACK 9/16" LARGE HEAD SCREW (5 used in this step) W 2 nd 15H J Surface with holes K Surface with holes 1 st 15H Page 15

16 Step 12 Fasten the other RETURN FRAME (W) to the BOTTOM (K). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). 1st - Insert a PIVOT HINGE (15H) into the lower center hole in the RETURN FRAME (W). Fasten the SHELF (J) to the PIVOT HINGE in the RETURN FRAME. Use a BLACK 9/16" LARGE HEAD SCREW (1S). 2nd - Then, insert a PIVOT HINGE (15H) into the upper center hole in the RETURN FRAME (W). Fasten the SHELF (J) to the PIVOT HINGE in the RETURN FRAME. Use a BLACK 9/16" LARGE HEAD SCREW (1S). 1S BLACK 9/16" LARGE HEAD SCREW (5 used in this step) W 15H 2 nd J K 1 st 15H Page 16

17 Step 13 Fasten the RETURN FRAMES (W) to the TOP (H2). Use six BLACK 3/4" PAN HEAD SCREWS (85S). 85S BLACK 3/4" PAN HEAD SCREW (6 used in this step) W W H2 Page 17

18 Step 14 Fasten a PIVOT HINGE (15H) to the FLIP DOWN DOOR (O). Use a BLACK 9/16" LARGE HEAD SCREW (1S). Fasten the STRIKE PLATE (6I) to the FLIP DOWN DOOR (O). Use a BLACK 1/2" FLAT HEAD SCREW (11S). NOTE: The surface of the STRIKE PLATE with "SAUDER" should be facing up. Insert a PIVOT HINGE (15H) into the WASHERS (9I) and into the CENTER UPRIGHT (D). Insert the PIVOT HINGE, which is fastened to the FLIP DOWN DOOR (O), into the hole in the UPRIGHT (C). You will need to tilt your DOOR slightly. Now, tip the FLIP DOWN DOOR (O) in and fasten the free HINGE to the DOOR. Use a BLACK 9/16" LARGE HEAD SCREW (1S). 11S BLACK 1/2" FLAT HEAD SCREW (1 used for the STRIKE PLATE) 15H O 6I 9I 1S 9I BLACK 9/16" LARGE HEAD SCREW (2 used for the PIVOT HINGES) 15H O D C Page 18

19 Step 15 Carefully stand your unit upright. Fasten the UPRIGHTS (C and D) to the LOWER TOP (F2). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). Fasten the LOWER MOLDING (Y) to the DESK FRAMES (V). Use two BLACK 3/4" PAN HEAD SCREWS (with flat end) (90S). Pro Tip: Lift with your legs. And, you know, your arms. 90S BLACK 3/4" PAN HEAD SCREW (with flat end) (2 used for the LOWER MOLDING) F2 V Y V C D 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Page 19

20 Step 16 Fasten the PULL (21K) to the DRAWER BOTTOM (T). Use two BLACK 1/2" FLAT HEAD SCREWS (11S). Fasten the DRAWER SIDES (R and S) to the DRAWER BOTTOM (T). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). Fasten the DRAWER BACK (Q) to the DRAWER SIDES (R and S). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). T 21K Surface with more holes 11S These surfaces should be the same color. BLACK 1/2" FLAT HEAD SCREW (2 used in this step) S Finished edge Q T Surface without PULL Surface and edge with HIDDEN CAM R The PULL on the other side is closer to this edge. Surface and edge with HIDDEN CAM 2S BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) Page 20

21 Step 17 Fasten the DRAWER FRONT (P) to the DRAWER SIDES (R and S). Tighten two HIDDEN CAMS. Fasten the EXTENSION SLIDES (35MC) to the DRAWER SIDES (R and S). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through the center slotted holes and #3. Maximum 210 degrees Minimum 190 degrees Arrow Open end S These edges should be almost even. Open end P R S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 21

22 Step 18 To insert the drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. 10 lbs. total 20 lbs. 70 lbs. 50 lbs. 10 lbs. 30 lbs. 30 lbs. Page 22

23 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: Overloaded shelves and drawers. Improper loading can cause the product to be top-heavy. Improperly moving furniture that is not designed and equipped with casters. Placing TVs on furniture items that are not designed to support a television is hazardous. Risk of injury. Top-heavy furniture can tip over. Overloaded shelves and drawers can break. Furniture can tip over or break if improperly moved. Physical injury. Furniture can be very heavy. Breakage of tops - particularly with double pedestal furniture (drawers at both ends). Risk of injury or death. TVs can be very heavy. Plus the weight and location of the picture tube tends to make TVs unbalanced and prone to tipping forward. Never exceed the weight limits shown in the instructions. Work from bottom to top when loading shelves and drawers. Place the heavier items on the lower shelves or in lower drawers. Unload shelves and drawers from top to bottom before moving the unit. Do not push furniture, especially on a carpeted floor. Have a friend help you lift the item and set it in place. Provide support to the center section of the top when lifting the furniture. This product is not designed to support a television. Page 29

Steele TV Stand Stock # BH

LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store