IMPORTANT! Recommended Tools. 7/16 Deep socket Phillips screwdriver

Size: px

Start display at page:

Download "IMPORTANT! Recommended Tools. 7/16 Deep socket Phillips screwdriver"

Kathryn Walker
6 years ago
Views:

IMPORTANT! Read all instructions carefully before commencing any work. Always wear proper safety equipment. Some installation steps will require two or more installers.

1 IMPORTANT! Read all instructions carefully before commencing any work. Always wear proper safety equipment. Some installation steps will require two or more installers. Recommended Tools Ratchet 10-mm Socket 7/16 Deep socket Phillips screwdriver A. Tonneau cover unpackaging and vehicle preparation. 1. Remove the two zip t ies that are holding the gas springs and the hardware kit. Items A and B in Figure Remove the frame s cross bar. This will require loosening four phillips head screws and three 7/16 nylock nuts. Items C and D in Figure 1, respectively. E G E C A H D C A B F Figure Remove the two phillips head screws holding the front frame brackets. Items E in Figure Remove the hinge assembly from the pockets on the frame (Figure 2). This will require loosening and removing the plastic threaded knobs. To remove the hinge assembly from the pocket, grab the frame as shown in Figure 3 and rotate up. WARNING! The hinge assembly is spring-loaded and could become a pinch point.

Hinge pocket Rotate in this direction Hinge Assembly Figure 2. Figure 3. WARNING! PINCH POINT 5.

Remove all of the foam blocks. Item H in Figure 1. 8. Clean the top and outer sides of the bed rails and tailgate. 9.

Remove the (six) top screws that hold the plastic bed liner. There are three on each side. See figure 4. Rear Center Front Figure 4. 2. Install the driver side and passenger side frames. See figure 5.

2 Hinge pocket Rotate in this direction Hinge Assembly Figure 2. Figure 3. WARNING! PINCH POINT 5. Pull on the emergency release handle to unlatch the passenger and driver side frames and remove them from the box. Item F in Figure Remove the 1 x 4 wood board. Item G in Figure Remove all of the foam blocks. Item H in Figure Clean the top and outer sides of the bed rails and tailgate. 9. Apply masking tape along the outer sides of the bed rails and tailgate to protect the paint during installation. See Figures 6, 7, and 8. B. Installing the tonneau cover. 1. Remove the (six) top screws that hold the plastic bed liner. There are three on each side. See figure 4. Rear Center Front Figure Install the driver side and passenger side frames. See figure 5. Note: At this time you should only install the rear and center 6 mm x 45mm screws. The front screws will be installed later along with a small bracket. Figure Install the front half of the tonneau cover. Carefully slide the front half of the tonneau cover thru the opening between the roll bars and the back of the cab. See figures 6, 7 and 8. Note: Apply masking tape as shown in Figure 6 to protect the painted surface of the vehicle during installation. 2

Masking Tape Figure 6. Figure 7. Figure 8. 4. Install the frame cross member. See Figure 9.

Install the front half mounting brackets on the driver side and passenger side frame.

nut. See figure 10. FRONT HALF MOUNTING BRACKET 1/4-20 NUT FRONT 6M

3 Masking Tape Figure 6. Figure 7. Figure Install the frame cross member. See Figure 9. Figure 9. 2 #10 SCREWS PER SIDE FRAME CROSS MEMBER 5. Install the front half mounting brackets on the driver side and passenger side frame. This bracket is attached using the front 6-mm x 45-mm screws that were not installed in step 2 and a 1/4-20 nut. See figure 10. FRONT HALF MOUNTING BRACKET 1/4-20 NUT FRONT 6MM X 45MM SCREW Figure Secure the front half of the tonneau cover to the frame. See figure 11. Front THREADED STUDS ON FRONT HALF OF TONNEAU COVER CAPTIVE NUT ON FRONT HALF OF TONNEAU COVER 1/4-20 NUT Front 1/4-20 SCREW 2 PLACES 3

7. Prepare the rear half of the tonneau cover for installation. Rotate the hinge assembly and insert the gas spring socket onto the ball stud. See Figure 12. WARNING!

Lift the rear half of the tonneau cover and hold over the bed of the truck.

4 7. Prepare the rear half of the tonneau cover for installation. Rotate the hinge assembly and insert the gas spring socket onto the ball stud. See Figure 12. WARNING! The hinge assembly is spring-loaded and could become a pinch point. Figure 12. WARNING! PINCH POINT 8. Install the rear half of the tonneau cover. Lift the rear half of the tonneau cover and hold over the bed of the truck. Lower the tonneau cover making sure that the hinge plates on the tonneau cover slip into the pockets on the side frames on the truck. See Figures 13 and 14. Note: Keep the tailgate of the vehicle open until installation has been completed and you have verified that you can open the tonneau cover using your key. Figure 13. Figure Secure the rear half of the tonneau cover. Install the threaded knob and spacer into the hole on both the driver and passenger side hinge plates. See figure 15. HINGE ASSEMBLY SPACER THREADED KNOB Figure 15. 4

5 10. Finally, secure the drain tube to the truck bed using the zip ties and adhesive-backed anchors included in the kit. See Figure 16. DRAIN TUBE Figure 16. 5

INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:

INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips