Fort Picnic Table & Lower Floor Install Version 10.13

Transcription

1 Fort Picnic Table & Lower Floor Install Version Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact Gun Claw Hammeror Rubber Mallet Pliers or Vise Grips 7/16 Deep Well Socket 9/16 Deep Well Socket 3/4 Deep Well Socket 1/8, 1/4, and 9/16 Drill Bits Phillips Head Screw Bits An Adult with two Adult Helpers Please familiarize yourself with the install manual, parts/components and general construction process of your new swing set before getting started. Approximate assembly time: 6 to 8 hours. 6 foot unobstructed safety perimeter around swing set recommended. Houston, TX kid STRUCTURES INC.

2 PicNic Table/ Lower floor Bundle Item No. Part Number Part Description FPT-1 FPT-2 FPT-3 FPT-4 FPT-5 FPT-6 FPT-7 FPT Universal Deck Board Uni. Fort Picnic table/ lower floor support Fort PICNIc table/ Lower Floor Board fort picnic table/ lower floor runner fort picnic table/ Lower Runner (No Holes) Fort PICNIC Table/lower Seat Runner fort picnic table/ seat runner (no holes) fort picnic table/ lower floor board QTY PTH-1 PTH-4 picnic table/ lower floor HARDWARE /8 USS FLatwasher 1/4 USS FLatwasher 1/4 x 4 1/2 Hex Lag bolt 3/8 x 3 1/2 Hex Lag bolt 2 1/2 Coated Deck Screw

3 fort picnic table/ lower floor lumber & hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE FPT Universal Deck Board QTY. 1 GIVE MANUAL TO OWNER.) FPT Fort Picnic Table Lower Floor Supports QTY. 4 FPT Fort Picnic Table/ Lower Floor Board QTY. 4 FPT Fort Picnic Table/ Lower Floor Runner QTY. 2 FPT Fort Picnic Table/ Lower Floor Runner( No Holes) QTY. 1 FPT Fort Picnic Table/ Lower Seat Runner QTY. 4 FPT Fort Picnic Table/ Lower Seat Runner(No Holes) QTY. 2 FPT Fort Picnic Table/ Lower Floor Board QTY. 7 Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE 1:1 SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

4 fort picnic table/ lower floor lumber & hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) PTH /8 Washers Qty /4 Washers Qty /4 x 4 1/2 Lag Bolt QTY. 12 PTH /8 x 3 1/2 Lag Bolt QTY /2 Coated Deck Screw QTY. 78 Measurement taken from bottom of bolt head to the bottom of bolt

5 Parts Needed FPT-4- Picnic Table/ Lower Floor Runner- (2) FPT-2- Picnic Table/ Lower Floor Board- (4) FPT-8- Fort Picnic Table/ Lower Floor Board- (3) Picnic Table Assembly - 2 1/2 Coated Deck Screw- (28) FPT-2 FPT-4 5 Gap on both sides FPT-8

6 Picnic Table Assembly Parts Needed FTP-5- Fort Picnic/ Lower Runner No holes- (1) FTP-8- Fort Picnic Table/ Lower Floor Board- (4) FTP-6- Fort Picnic Table/ Lower Seat Runner- (4) FTP-1- Universal Deck Board- (1) 28 3/4 Gap on Both Sides 5 Gap on Both Sides FPT-1 Seat Assembly - 2 1/2 Coated Deck Screw- (26) FPT-8 1 1/2 Gap on Both Sides FPT-6 FPT-5

7 Seat Assembly Parts Needed FPT-7- Fort Picnic Table/ Seat Runner- (2) FPT-2- Fort Picnic Table/ Lower Floor Support- (4) - 2 1/2 Coated Deck Screw- (12) PTH-4-3/8 x 3 1/2 Hex Lag Screw- (8) PTH-1-3/8 USS Flatwasher- (8) FPT /4 Gap on each side FPT-2 20 Gap From ground to bottom of FTP /4 Gap on each side 6 Gap From ground to bottom of FTP-2 PTH-1 PTH-4

8 Picnic Table Assembly Parts Needed Assembled Seats- (2) Assembled Table- (1) - 1/4 x 4 1/2 Hex Lag Screw- (12) - 1/4 USS Flatwasher- (12) Assembled Table Assembled Seat

9 Lower floor Assembly Parts Needed FPT-2- Fort Picnic Table/ Lower Floor Support- (2) Assembled Seat- (1) PTH-4-3/8 x 3 1/2 Hex Lag Screw- (4) PTH-1-3/8 USS Flatwasher- (4) FPT-2 1/2 Gap From ground to bottom of FTP-2 Take off the 2, 4-Hole Facias to get under for lagging down Assembled Seat PTH-1 PTH-4

10 Lower floor Assembly Parts Needed Assembled Seats- (1) Assembled Table- (1) - 1/4 x 4 1/2 Hex Lag Screw- (8) - 1/4 USS Flatwasher- (8) Assembled Seat Assembled Table

11 Lower floor Assembly Parts Needed Assembled Seats- (1) Assembled Table- (1) - 1/4 x 4 1/2 Hex Lag Screw- (8) - 1/4 USS Flatwasher- (8) Assembled Seat Put back on the 4-Hole Facia taken off to get under for lagging down Assemblies

12 Lower floor Finished