Rainforest Cottage Install Manual Version 2.17

Transcription

1 Rainforest Cottage Install Manual Version.7 Tools Needed for Assembly Tape Measure 4 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact Gun Claw Hammer or Rubber Mallet Pliers or Vise Grips 7/6 Deep Well Socket 9/6 Deep Well Socket 3/4 Deep Well Socket /8, /4, and 9/6 Drill Bits Phillips Head Screw Bits An Adult with two Adult Helpers Please familiarize yourself with the install manual, parts/components and general construction process of your new swing set before getting started. Approximate assembly time: 6 to 8 hours. 6 foot unobstructed safety perimeter around swing set recommended. HOUSTON, TX KID STRUCTURES INC.

2 When choosing a location for your swing set, always keep your child or children s safety in mind. Here are some recommendations to help you locate and install a safe play area. This play set is designed for the use of 4 occupants who have a combined weight not exceeding 800 pounds on the elevated floor; 3 occupants who have a combined weight of 55 pounds on the swing area; for a total Unit capacity of 5 occupants who have a combined weight of 35. (this weight is not including the picnic table area) On-site adult supervision is required. The swing set should be located on level ground. The stationary components such as ladders and slides are required to be a minimum of six feet from any structure or obstruction such as a fence, garage, house, tree, overhanging branches, electrical wires, clotheslines, etc. Any swinging equipment is also required to be a minimum distance twice the height of the swing beam away from these obstructions or structures as well. The swing set should be located a safe distance from any water hazards, such as a lake, river, bayou, swimming pool, etc. Do not install this residential swing set in a commercial setting. This swing set is not manufactured for commercial usage and will void all warranties. Tree Frogs Wooden Swing Set Factory is not responsible for any damages or injuries resulting from this swing set being used in a commercial setting. Never install this swing set indoors; or over concrete, asphalt, packed earth, grass, carpet or any other hard surface. A fall onto a hard surface can result in serious or fatal injury. The U.S. Consumer Product Safety Commission (CPSC) recommends that you install and maintain a resilient surface under your swing set. The CPSC s Consumer Information Sheet for Playground Surfacing Materials is on the next page. A resilient surface, should be installed after the swing set has been completely assembled according to these instructions. The swing set must rest on solid ground. Please note that this swing set has a maximum fall height of 7. Here are some maintenance tips required to insure safe play on your swing set for years of fun. At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed, swing seats, chains, ladders, slides, rope and wood components for sign of deterioration and replace if necessary. On a yearly basis, we recommend that you coat your swing set with a sealant or preservative. You may also want to spot sand any areas prior to sealing. ** Special note: Although we recommend that you reseal your swing set annually, you may have to touch up the high traffic areas and/or areas that have a high exposure to direct sunlight.** Be sure that the sealant you select is non-toxic and child safe. Your local Tree Frogs Wooden Swing Set Factory dealer may offer a complete power wash and reseal and maintenance program. Do not use line trimmers or weed eaters around your swing set. The line will remove both paint and wood from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited warranty. Remove plastic swing seats and take in doors or do not use when temperature drops below 0 F. Weight Limits for Tree Frogs Swing Sets Fort Platform: 800 Lbs. Total Weight Swing Belts: 75 Lbs. Trapeze: 5 Lbs. Full Bucket Swing: 50 Lbs. Toddler Bucket Swing: 50 Lbs. Tire Swing: 5 Lbs. Total Weight Rope Ladder: 75 Lbs. Rock Wall: 50 Lbs. All Slides: 5 Lbs. Tree Frogs recommends that the weight limits for all components must not be exceeded. Failure to adhere to these and other safety guidelines could result in damage to the swing set and/or injury to the users. Please keep this install manual for future reference.

3 To insure SAFE PLAY adults must teach children: Not to walk close to, in front of, behind, or between moving items. Not to swing empty swing seats. Not to swing sideways into the path of adjacent swings. Not to use the swing set in a manner other than that for which it is intended. Not to get off the equipment while it is in motion. Not to jump off the tower. Not to stand in the swing seats. Not to swing so high that chains become slack, or above the height of the swing support. Not to jump on a slide. Not to climb on top of the swing support. Not to attach to the swing set any item that is not specifically designed for use with the equipment, such as (but not limited to) jump ropes, clotheslines, pet leashes, cables, and chains. These may become strangulation hazards. To hold on to swings and climbers with both hands. To slide feet first, never head first. To watch for other children while swinging or playing near the swing set. To also insure SAFE PLAY adults must: Limit climbing and swinging heights to each child s ability. Verify that suspended climbing ropes are secured at both ends. Verify that suspended climbing ropes cannot be looped back on themselves. Dress children appropriately for play. Use well-fitted shoes that do not have slippery soles. Avoid ponchos, scarves, hoods, loose fitting clothing, neckties, and any clothing with a drawstring. Serious injury could result should any part of the children s clothing become entangled in the swing set. Do not allow children to play wearing helmets. Remember that children are inventive. When they develop games that are unsafe, be alert and change the rules. IMPORTANT - PLEASE READ As fresh lumber acclimates to its new environment, the natural tendencies of the tree can show itself in the form of checks, or cracks in the lumber. In almost all cases this is normal and it will not affect the structural integrity of your play set. Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, checking or any other physical properties of wood that do not present a safety hazard, are not covered by this warranty. Defects that develop because the product is exposed to extreme climate conditions are not covered by this warranty. Defects that develop as a result of faulty or improper installation of the product are also not covered by this warranty. Most cracks are not warrantable, however if you believe that the integrity of your play set is compromised by this natural occurrence, please contact the Tree Frogs Swing Set Dealer that you purchased your swing set from. We appreciate your purchase and know that you will enjoy your play system for many years to come.

4 Depending on your experience, assembly of our play sets can take as little as 6 hours up to 4 hours, depending on size, after inventory of parts; therefore, we recommend you set aside a full two days for assembly. Identify all of the parts for your play set. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. After everything is laid out, check carefully to ensure all parts are present. Make sure there are no broken boards. Find an area to sort your hardware. It is best to open the hardware on a solid surface so that you do not lose any pieces in the grass. This will save time and familiarize you with all the different pieces in the hardware bag. **Important note: Wood has some natural defects such as knots, surface cracks, etc... We reject parts that are structurally defective. We use a high quality lumber in our structures; however, you should inspect each part for splinters or rough spots and sand them smooth to prevent injury.** After familiarizing yourself with all of the components, read all instructions thoroughly. Reading instructions after you have studied the parts will help you understand more clearly the installation process, and help to eliminate unnecessary mistakes. Pay close attention to the diameter and length of each bolt and screw. Never tighten hardware completely at first. It helps to have some adjustment for bolt alignment while you are attaching parts together. After everything is square, tighten each joint. After the main unit is assembled it is critical that the floor is level and square. If the main frame is not level, the walls and floor will be out of square. After you complete installation, make sure every bolt, screw, and nut is tight, and every board is secure. Wood will expand and contract with the seasons. Place the set on level ground, not less than 6ft from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. All /4 and 3/8 lag bolts must have pre-drilled holes -/ to deep. Use a /8 drill bit for the /4 lag bolts and /4 drill bit for 3/8 lag bolts. Use pre-drilled holes in facias as a reference for placing lag bolt pilot holes. If a board lifts or rises causing a gap between boards when running in lag bolts or screws, back out the screw or lag bolt and press or apply pressure (but not enough to crack or break board) while re running in the lag bolt or screw in the same hole. Do not over tighten bolts, lag bolts or screws. You can damage boards, break hardware, and/or strip out the hardware. When using hammer do not beat on the hardware, but gently tap it in. Never beat on the wood as it will leave marks. Complete the steps which will be the basic frame of the fort {i.e. four corner posts with base (sand box boards) and deck supports} Position in the most level area chosen for the play set, keeping in mind the location and size of the swing beam, ladder, slides, etc. that extend off the fort. Once the frame is in the final position, check for vertical and horizontal levelness to determine which side(s) will need to be dug into the ground to level the play set. With a shovel, score the ground around the outside edges of the sandbox boards on the high side of the fort. This is the area that will be dug in. Make sure to score deep enough; the scored lines will be your digging template. Push the frame off and away from the scored area, far enough to dig and remove dirt to reach the appropriate depth. Dig a channel along the scored line(s) for the base of the fort (corner post and sandbox boards) to rest into. Dig the channel(s) to the same level depth. The bottom of the channel(s) should be level to each other so your frame doesn t teeter or rock because the channel(s) are uneven. Once you have removed enough grass and dirt, slide/push the frame into the channel(s). Place a level on the vertical and horizontal boards of the frame to determine if enough soil, or too much, was removed. Repeat this process until the basic frame is plumb and level and in its final position before completing the rest of the assembly. Measure to make sure fort is square. ** Important: if you require a channel depth of more than 6, then we recommend you have your play set area professionally graded before completing assembly. **

5 CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS The U.S. Consumer Product Safety Commission (CPSC) estimates that about 00,000 playground equipment related injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall onto a shockabsorbing surface is less likely to cause a serious injury than a fall onto a hard surface. However, it should be recognized that some injuries from falls will occur no matter what playground surfacing material is used. Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Grass may appear to be acceptable, but can turn to hard packed earth in areas of high traffic. Shredded bark mulch, wood chips, or fine gravel are considered to be acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around play equipment. TABLE -CRITICAL HEIGHTS (in feet) OF TESTED MATERIAL MATERIAL UNCOMPRESSED DEPTH COMPRESSED DEPTH 6 Inch 9 Inch Inch 9 inch Wood Chips Double Shredded Bark Mulch Engineered Wood Fibers 6 7 > 6 Fine Sand Coarse Sand Fine Gravel Medium Gravel Shredded Tires** 0- N/A N/A N/A ** This is data from tests conducted by independent testing laboratories on a 6 inch depth of uncompressed shredded tire samples produced by four manufacturers. The test reported critical heights, which varied from 0 feet to greater than feet. It is recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F9. Table should be read as follows: If, for example, uncompressed wood chips are used at a minimum of 6 inches, the Critical Height is 7 feet. If 9 inches of uncompressed wood chips are used, the Critical Height is 0 feet. It should be noted that, for some materials, the Critical Height decreases when the material is compressed. It is recommended that a shock absorbing material should extend a minimum of 6 feet in all directions from the perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure. This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability in your area, and its cost. This information has been extracted from the CPSC publications Playground Surfacing-Technical Information Guide and Handbook for Public Playground Safety. Copies of these reports can be obtained by sending a postcard to: Office of Public Affairs U.S. Consumer Product Safety Commission Washington, D.C. 007 Toll-free Hotline: or at

6 Item No. Part No. Part Description QTY. RFC- RFC- RFC-3 RFC-4 RFC-5 RFC-6 RFC-7 RFC-8 RFC-9 RFC-0 RFC- RFC- RFC-3 RFC-4 RFC-5 RFC-6 RFC-7 RFC-8 RFC-9 RFC-0 RFC- RFC- RFC-3 RFC-4 RFC-5 RFC-6 RFC-7 RFC-8 RFC-9 RFC-30 RFC-3 RFC-3 RFC-33 RFC-34 RFC-35 RFC-36 RFC-37 RFC-38 RFC-39 RFC-40 RFC-4 RFC-4 RFC-43 Rainforest Cottage- Base Lumber 7 5/8 WOOD ROOF FAN BOARD # 3 /6 WOOD ROOF FAN BOARD # 5 3/4 CHIMNEY BLOCK #3 7 CHIMNEY BLOCK #4 5 3/6 WOOD ROOF FAN BOTTOM 48 /6 WOOD ROOF TOPPER 5 3/6 WOOD ROOF TOPPER 5 / RAIL PICKET 37 5/6 PICNIC SEAT BOARD SHORT -HOLE FACIA 6 TIC TAC TOE BOARD CENTER SUPPORT FACIA 33 3/4 WOOD ROOF CENTER SUPPORT 44 PICNIC SEAT BOARD 44 SLIM 4- HOLE FACIA 56 3/6 LADDER SIDE RAIL SUPPORT FACIA 9 5/8 ROPE HOLE FACIA 9 5/8 UPPER 6-HOLE FACIA 48 /6 WOOD ROOF TOPPER # 5 3/6 WOOD ROOF TOPPER # 44 PICNIC TABLE BOARD 8 3/8 WOOD ROOF PEAK 5 / TIC TAC TOE FILLER ARCH 44 DECK BOARD 8 -ROCK ROCKWALL BOARD 8 - ROCK ROCKWALL BOARD 8 BLANK ROCKWALL BOARD 8 ROCKWALL BOARD W/ ROPE HOLE HOLE FACIA HOLE FACIA 44 PICNIC SEAT BOARD 9 5/8 DECK SUPPORT 9 5/8 0- HOLE FACIA 9 5/8 LADDER SIDE RUNNER 9 5/8 ROCKWALL SIDE RUNNER 8 3/6 WOOD ROOF FAN PLATE 5 3/8 PICNIC SEAT BENCH SUPPORT 7 GUSSET 8 3/6 OUTSIDE PICNIC BENCH SUPPORT LADDER STEP 3 3/4 LADDER SUPPORT 3 5/8 PICNIC TABLE SUPPORT 35 WOOD ROOF SUPPORT

7 Rainforest Cottage- Base Lumber Item No. Part No. Part Description QTY. RFC-44 RFC-45 RFC-46 RFC-47 RFC-48 RFC-49 RFC-50 RFC-5 RFC-5 RFC-53 RFC-54 RFC-55 RFC-56 RFC-57 RFC-58 RFC-59 RFC-60 RFC-6 65 /8 ROCKWALL SUPPORT LEG 69 7/6 LEFT LADDER LEG 69 7/6 RIGHT LADDER LEG 35 WOOD ROOF EXTENSION 9 5/8 MAINBEAM /8 PICNIC SEAT LEG 8 3/6 TRAPEZE GUSSET 4 /8 PICNIC TABLE LEG 44 SWINGBEAM TOP JOIST 76 3/8 TRAPEZE ARM 03 CENTER POST 03 CORNER POST 08 / CORNER POST 9 9/6 CHIMNEY BLOCK # 3 CHIMNEY BLOCK # 48 /6 SB SIDE WOOD ROOF BOARD 5 3/6 (L) WOOD ROOF BOARD- TRAPEZE 5 3/6 (R) WOOD ROOF BOARD-TRAPEZE Rainforest Cottage- Treehouse Panel Lumber RFTP- RFTP- RFTP-3 RFTP-4 RFTP-5 RFTP-6 RFTP-7 RFTP-8 RFTP-9 RFTP-0 RFTP- RFTP- RFTP-3 RFTP-4 RFTP-5 RFTP-6 RFTP-7 RFTP-8 RFTP-9 RFTP-0 RFTP- RFTP- 6 / LOWER SB SIDE PANEL BOARD 0 /6 UNDER FAN BOARD 6 / PANEL BOARD 6 /4 UPPER LEMONADE BOARD 0 / UNDER FAN ANGLE CUT /4 (L) SHUTTER FOR TRAPEZE SIDE /4 (R) SHUTTER FOR TRAPEZE SIDE (L) WINDOW SHUTTER FOR SIDE (R) WINDOW SHUTTER FOR SIDE 4 /4 LOWER LEFT SHUTTER 4 /4 LOWER RIGHT SHUTTER 6 3/4 (L) SB SHUTTER 6 3/4 (L) SB SIDE SHUTTER 6 3/4 (R) SB SHUTTER 6 3/4 (R) SIDE SHUTTER 3 /6 CORNER ANGLE BOARD 6 / LOWER PANEL BOARD 8 3/6 CORNER ANGLE BOARD SB SIDE 44 / LOWER PANEL BOARD 7 /4 UPPER PANEL BOARD 7 /4 UPPER PANEL BOARD FOR SHUTTERS 4 9/6 SB SIDE UNDER FAN CENTER BOARD

8 Rainforest Cottage- Treehouse Panel Lumber Item No. Part No. Part Description QTY. RFTP-3 RFTP-4 RFTP-5 RFTP-6 RFTP-7 RFTP-8 RFTP-9 RFTP-30 RFTP-3 RFTP-3 RFTP-33 RFTP-34 RFTP-35 RFTP-36 SBL- SBL- SBL-3 SBL-4 SBL-5 SBL-6 6 /6 UPPER PANEL BOARD FOR SHUTTER 6 /6 UPPER PANEL BOARD FOR END 6 / RAIL PICKET FOR TREEHOUSE 3 9/6 SB SIDE UPPER CENTER BOARD 8 /4 CENTER WOOD ROOF SUPPORT 3/4 LEMONADE WOOF ROOF SUPPORT 8 /6 PANEL SUPPORT 44 SLIM 4- HOLE FACIA 47 3/6 WINDOW ARCHES 3 /4 LEMONADE STAND COUNTER 44 WINDOW TOP 44 LEMONADE FACIA 44 LEMONADE 4 HOLE FACIA 45 3/4 LEMONADE WOOD ROOF BOARD Rainforest Cottage- Swingbeam Lumber 7 5/8 CENTER A-FRAME BLOCK 7/8 A-FRAME BLOCK 7/8 A-FRAME BLOCK SINKED 68 A-FRAME CROSSMEMBER 3 A-FRAME LEG 3- POSITION SWINGBEAM 5

9 Rainforest Cottage- Base Hardware Item No. Part No. Part Description QTY. RFH- RFH- RFH-3 RFH-4 RFH-5 RFH-6 RFH-7 RFH-8 RFH-9 RFH-0 RFH- RFH- RFH-3 RFH-4 RFH-5 RFH /8 ACORN NUT PLATED 5/8 COATED DECK SCREW / COATED DECK SCREW 3/8 HEX NUT 3/8 4-PRONG T-NUT 3/8 X 4 / HEX BOLT 3/8 X 6 HEX BOLT /4 X / HEX LAG SCREW /4 X 3 HEX LAG SCREW 3/8 X 3 / HEX LAG SCREW 3/8 SPLIT LOCKWASHER /4 USS FLATWASHER 3/8 USS FLATWASHER 3/8 NYLON INSERT LOCKNUT #4 X PAN PHILLIPS T/S 3/8 BOLT CUP Rainforest Cottage- Picnic Table Hardware PTH- PTH- PTH-3 PTH-4 WRH- WRH- WRH-3 WRH-4 WRH-5 WRH-6 WRH-7 WRH-8 WRH / COATED DECK SCREW /4 X 3 HEX LAG SCREW /4 USS FLATWASHER /4 X HEX LAG SCREW Rainforest Cottage- Wood Roof Hardware /8 4-PRONG T-NUT 3/8 BOLT CUP 3/8 X 4 / HEX BOLT / COATED DECK SCREW COATED DECK SCREW / COATED DECK SCREW /4 USS FLATWASHER /4 X HEX LAG SCREW 5/8 COATED DECK SCREW

10 Rainforest Cottage- Rockwall Hardware Item No. Part No. Part Description QTY. RWH- RWH- RWH-3 RWH-4 RWH-5 RWH-6 RWH-7 RWH COATED DECK SCREW /4 X /4 PAN PHILLIPS M/S /4 4-PRONG T-NUT /4 USS FLATWASHER #4 X PAN PHILLIPS T/S 3/8 4-PRONG T-NUT 3/8 X / HEX BOLT 3/8 USS FLATWASHER Rainforest Cottage- Step Ladder Hardware SLH- SLH- SLH-3 SLH-4 SLH-5 SLH / COATED DECK SCREW 3/8 4-PRONG T-NUT #4 X PAN PHILLIPS T/S /4 USS FLATWASHER 3/8 X / HEX BOLT 3/8 USS FLATWASHER Rainforest Cottage- Slide Hardware SH- SH- SH /4 USS FLATWASHER /4 X PAN PHILLIPS M/S /4 4-PRONG T-NUT Rainforest Cottage- Tic Tac Toe Hardware TH /8 COATED DECK SCREW 8

11 Rainforest Cottage- Swingbeam Hardware Item No. Part No. Part Description QTY. SBH- SBH- SBH-3 SBH-4 SBH-5 SBH-6 SBH-7 SBH-8 SBH-9 SBH-0 SBH- SBH- SBH-3 SBH-4 SBH-5 SBH-6 SBH-7 SBH-8 SBH-9 SBH-0 TPH- TPH- TPH /8 ACORN NUT PLATED / ACORN NUTPLATED / X 3 / CARRIAGE BOLT / X 7 CARRIAGE BOLT / X 9 CARRIAGE BOLT 3/8 HEX NUT / HEX NUT 3/8 X 7 HEX BOLT 3/8 X 3 / HEX LAG SCREW 3/8 X 5 HEX LAG SCREW 3/8 NYLON INSERT LOCKNUT 3/8 SPLIT LOCKWASHER / SPLIT LOCKWASHER 3/8 USS FLATWASHER / USS FLATWASHER 3/4 USS FLATWASHER 3/8 X 0 HEX BOLT #4 X PAN PHILLIPS T/S / X HEX BOLT 3/8 BOLT CUP Rainforest Cottage- Treehouse Hardware /8 COATED DECK SCREW /4 X 3 HEX LAG SCREW /4 USS FLATWASHER

12 Rainforest Cottage- Base Accessories Item No. Part No. Part Description QTY. RFA- RFA- RFA-3 RFA-4 RFA-5 RFA-6 RFA-7 RFA-8 RFA-9 RFA-0 RFA- RFA- RFA-3 RFA-4 RFA-5 RFA DUCTILE IRON SWING HANGER PLAYGRIP U-MOUNT LADDER HANDLE /4 PLAYGRIP SAFETY HANDLE SWINGBEAM TRI-PLATE 6 TRAPEZE BAR W/ RINGS SWINGBEAM 45 DEGREE BRACKET SPRING CLIPS 0 X 00MM DISC SWING TELESCOPE 90 DEGREE BRACKET 4 YELLOW ROPE SHIP S WHEEL SPIRAL GROUND ANCHOR 90 DEGREE LADDER/ ROCKWALL BRACKET TIC TAC TOE SET X CHALKBOARD PANEL Rainforest Cottage- Box A. & B. Accessories (Color Depends on Package) BAB- BAB XX XX ROCKWALL ROCKS 66 CHAINED BELT SWING

13 Rainforest Cottage- Base Lumber RFC- RFC- RFC-3 RFC-4 7 5/8 Wood Roof Fan Board # QTY. 4 3 /6 Wood Roof Fan Board # QTY. 5 3/4 Chimney Block #3 QTY. 7 Chimney Block #4 QTY. RFC-5 RFC-6 RFC-7 RFC-8 5 3/6 Wood Roof Fan Bottom QTY. 48 /6 Wood Roof Topper QTY. 5 3/6 Wood Roof Topper QTY. 5 / Rail Picket QTY. 3 RFC-9 RFC-0 RFC- RFC- 37 5/6 Picnic Seat Board QTY. 4 Short - Hole Facia QTY. 3 6 Tic Tac Toe Board QTY. Center Support Facia QTY.

14 Rainforest Cottage- Base Lumber RFC-3 RFC-4 RFC-5 RFC /4 Wood Roof Center Support QTY Picnic Seat Board QTY Slim 4- Hole Facia QTY /6 Ladder Side Rail Support Facia QTY. RFC-7 RFC-8 RFC-9 RFC-0 9 5/8 Rope Hole Facia QTY. 9 5/8 Upper 6- Hole Facia QTY. 48 /6 Wood Roof Topper # QTY. 5 3/6 Wood Roof Topper # QTY. RFC- RFC- RFC-3 RFC-4 44 Picnic Table Board QTY /8 Wood Roof Peak QTY. 3 5 / Tic Tac Toe Filler Arch QTY. 44 Deck Board QTY. 6

15 Rainforest Cottage- Base Lumber RFC-5 RFC-6 RFC-7 RFC Rock Rockwall Board QTY Rock Rockwall Board QTY. 3 8 Blank Rockwall Board QTY. 4 8 Rockwall Board w/ Rope Hole QTY. RFC-9 RFC-30 RFC-3 RFC Hole Facia QTY Hole Facia QTY. 44 Picnic Seat Board QTY. 9 5/8 Deck Support QTY. RFC-33 RFC-34 RFC-35 RFC /8 0 Hole Facia QTY. 9 5/8 Ladder Side Runner QTY. 9 5/8 Rockwall Side Runner QTY. 8 3/6 Wood Roof Fan Plate QTY.

16 Rainforest Cottage- Base Lumber RFC-37 RFC-38 RFC-39 RFC /8 Picnic Seat Bench Support QTY. 7 Gusset QTY /6 Outside Picnic Bench Support QTY. Ladder Step QTY. 5 RFC-4 RFC-4 RFC-43 RFC /4 Ladder Support QTY. 3 5/8 Picnic Table Support QTY. 35 Wood Roof Support QTY /8 Rockwall Support Leg QTY. RFC-45 RFC-46 RFC-47 RFC /6 Left Ladder Leg QTY. 69 7/6 Right Ladder Leg QTY. 35 Wood Roof Extension QTY. 9 5/8 Mainbeam QTY.

17 Rainforest Cottage- Base Lumber RFC-49 RFC-50 RFC-5 RFC-5 /8 Picnic Seat Leg QTY. 8 3/6 Trapeze Gusset QTY. 4 /8 Picnic Table Leg QTY. 44 Swingbeam Top Joist QTY. RFC-53 RFC-54 RFC-55 RFC /8 Trapeze Arm QTY. 03 Center Post QTY. 03 Corner Post QTY. 08 / Corner Post QTY. RFC-57 RFC-58 RFC-59 RFC /6 Chimney Block # QTY. 3 Chimney BLock # QTY. 48 /6 SB Side Wood Roof Board QTY /6 (L) Wood Roof Board- Trapeze QTY. 8

18 Rainforest Cottage- Base Lumber RFC-6 5 3/6 (R) Wood Roof Board- Trapeze QTY. 8

19 Rainforest Cottage- Treehouse Panel Lumber RFTP- RFTP- RFTP-3 RFTP-4 6 / Lower SB Side Panel Board QTY. 0 /6 Under Fan Board QTY. 6 / Panel Board QTY. 6 /4 Upper Lemonade Board QTY. 3 RFTP-5 RFTP-6 RFTP-7 RFTP-8 0 / Under Fan Angle Cut QTY. 4 /4 (L) Shutter For Trapeze Side QTY. /4 (R) Shutter For Trapeze Side QTY. (L) Window Shutter For Side QTY. 4 RFTP-9 RFTP-0 RFTP- RFTP- (R) Window Shutter For Side QTY. 4 4 /4 Lower Left Shutter QTY. 4 /4 Lower Right Shutter QTY. 6 3/4 (L) SB Shutter QTY.

20 Rainforest Cottage- Treehouse Panel Lumber RFTP-3 RFTP-4 RFTP-5 RFTP-6 6 3/4 (L) SB Side Shutter QTY. 6 3/4 (R) SB Shutter QTY. 6 3/4 (R) SB Side Shutter QTY. 3 /6 Corner Angle Board QTY. RFTP-7 RFTP-8 RFTP-9 RFTP-0 6 / Lower Panel Board QTY. 8 3/6 Corner Angle Board SB Side QTY. 44 / Lower Panel Board QTY. 7 /4 Upper Panel Board QTY. 6 RFTP- RFTP- RFTP-3 RFTP-4 7 /4 Upper Panel Board For Shutters QTY /6 SB Side Under Fan Center Board QTY. 6 /6 Upper Panel Board For Shutter QTY. 6 /6 Upper Panel For End QTY.

21 Rainforest Cottage- Treehouse Panel Lumber RFTP-5 RFTP-6 RFTP-7 RFTP-8 6 / Rail Picket For Treehouse QTY /6 SB Side Upper Center Board QTY. 8 /4 Center Wood Roof Support QTY. 3/4 Lemonade Wood Roof Support QTY. RFTP-9 RFTP-30 RFTP-3 RFTP-3 8 /6 Panel Support QTY. 44 Slim 4- Hole Facia QTY. 47 3/6 Window Arches QTY. 3 /4 Lemonade Stand Counter QTY. RFTP-33 RFTP-34 RFTP-35 RFTP Window Top QTY. 44 Lemonade Facia QTY. 44 Lemonade 4- Hole Facia QTY. 45 3/4 Lemonade Wood Roof Board QTY.

22 Rainforest Cottage- Swingbeam Lumber SBL- SBL- SBL-3 SBL-4 7 5/8 Center A-Frame Block QTY. 7/8 A-Frame Block QTY. 7/8 A-Frame Block Sinked QTY. 68 A-Frame Crossmember QTY. SBL-5 SBL-6 3 A-Frame Leg QTY. 3- Position Swingbeam

23 RAINFOREST COTTAGE- BASE HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) RFH /8 Acorn Nut Plated QTY. 4 RFH /8 Coated Deck Screw QTY. 5 RFH / Coated Deck Screw QTY. 76 RFH /8 Hex Nut QTY. 4 RFH /8 4- Prong T-Nut QTY. 6 RFH /8 x 4 / Hex Bolt QTY. 0 RFH /4 x / Hex Lag Screw QTY. 0 RFH /8 x 6 Hex Bolt QTY. 4 RFH /4 x 3 Hex Lag Screw QTY. 96 RFH /8 x 3 / Hex Lag Screw QTY. 3 RFH /8 Split Lockwasher QTY. 8 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

24 RAINFOREST COTTAGE- BASE HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) RFH /4 USS Flatwasher QTY. 3 RFH /8 USS Flatwasher QTY. 0 RFH /8 Nylon Insert Locknut QTY. 4 RFH #4 x Pan Phillips T/S QTY. 6 RFH /8 Bolt Cup QTY. 8 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

25 RAINFOREST COTTAGE- PICNIC TABLE HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) PTH / Coated Deck Screw QTY. 48 PTH /4 x 3 Hex Lag Screw QTY. 4 PTH /4 USS Flatwasher QTY. 8 PTH /4 x Hex Lag Screw QTY. 4 RAINFOREST COTTAGE- WOOD ROOF HARDWARE BAG WRH /8 4- Prong T-Nut QTY. 6 WRH /8 Bolt Cup QTY. 6 WRH /8 x 4 / Hex Bolt QTY. 6 WRH / Coated Deck Screw QTY. 8 WRH Coated Deck Screw QTY. 5 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

26 RAINFOREST COTTAGE- WOOD ROOF HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) WRH / Coated Deck Screw QTY. 3 WRH /4 USS Flatwasher QTY. 8 WRH /4 x Hex Lag Screw QTY. 8 WRH /8 Coated Deck Screw QTY. 88 RAINFOREST COTTAGE- ROCKWALL HARDWARE RWH Coated Deck Screw QTY. 48 RWH /4 x /4 Pan Phillips M/S QTY. RWH /4 4- Prong T-Nut QTY. RWH /4 USS Flatwasher QTY. 8 RWH #4 x Pan Phillips T/S QTY. 6 RWH /8 4- Prong T-Nut QTY. RWH /8 x / Hex Bolt QTY. RWH /8 USS Flatwasher QTY. MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

27 RAINFOREST COTTAGE- STEP LADDER HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) SLH / Coated Deck Screw QTY. 4 SLH /8 4- Prong T-Nut QTY. SLH #4 x Pan Phillips T/S QTY. 4 SLH /4 USS Flatwasher QTY. 4 SLH /8 USS Flatwasher QTY. SLH /8 x / Hex Bolt QTY. RAINFOREST COTTAGE- TIC TAC TOE HARDWARE TH /8 Coated Deck Screw QTY. 8 RAINFOREST COTTAGE- SLIDE HARDWARE SH /4 USS Flatwasher QTY. 3 SH /4 x Pan Phillips M/S QTY. 3 SLH /4 4- Prong T-Nut QTY. 3 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

28 RAINFOREST COTTAGE- SWINGBEAM HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) SBH /8 Acorn Nut Plated QTY. 0 SBH / Acorn Nut Plated QTY. 8 SBH / x 3 / Carriage Bolt QTY. SBH / x 7 Carriage Bolt QTY. 4 SBH / x 9 Carriage Bolt QTY. MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

29 RAINFOREST COTTAGE- HARDWARE SWINGBEAMHARDWARE BAG BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) SBH /8 Hex Nut QTY. SBH / Hex Nut QTY. 8 SBH /8 x 3 / Hex Lag Screw QTY. SBH /8 x 7 Hex Bolt QTY. 8 SBH /8 x 5 Hex Lag Screw QTY. SBH /8 Nylon Insert Locknut QTY. 8 SBH /8 Split Lockwasher QTY. 0 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

30 RAINFOREST COTTAGE- SWINGBEAM HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) SBH / Split Lockwasher QTY. 8 SBH /8 USS Flatwasher QTY. 4 SBH / USS Flatwasher QTY. 9 SBH /4 USS Flatwasher QTY. 7 SBH #4 x Pan Phillips T/S QTY. SBH /8 x 0 Hex Bolt QTY. SBH / x Hex Bolt QTY. MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

31 RAINFOREST COTTAGE- SWINGBEAM HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) SBH /8 Bolt Cup QTY. 0 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

32 RAINFOREST COTTAGE- TREEHOUSE HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) TPH /8 Coated Deck Screw QTY. 357 TPH /4 x 3 Hex Lag Screw QTY. 8 TPH /4 USS Flatwasher QTY. 8 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

33 Rainforest Cottage- Base Accessories RFA Ductile Iron Swing Hanger QTY. 6 RFA Playgrip U-Mount Ladder Handle QTY. RFA /4 Playgrip Safety Handle QTY. RFA Swingbeam Tri-Plate QTY. RFA Trapeze Bar w/ Rings QTY. RFA Swingbeam 45 Degree Bracket QTY. RFA Spring Clips 0 x 00mm QTY. 6 RFA Disc Swing QTY. RFA Telescope QTY. RFA Degree Bracket QTY. 9 RFA Yellow Rope QTY. RFA Ship s Wheel QTY.

34 Rainforest Cottage- Base Accessories RFA Spiral Ground Anchor QTY. 4 RFA Degree Ladder/ Rockwall Bracket QTY. 4 RFA Tic Tac Toe Set QTY. RFA x Chalkboard Panel QTY. Rainforest Cottage- Base Accessories BAB XX Rockwall Rocks QTY. BAB XX 66 Chained Belt Swing QTY.

35 PARTS NEEDED RFC-40- Ladder Step- (5) RFC /6 Right Ladder Leg- () RFC /6 Left Ladder Leg- () RFA-4-90 Degree Ladder/ Rockwall Bracket- () Rainforest Cottage- Sub Assemblies SLH-- / Coated Deck Screw- (0) SLH-5-3/8 x / Hex Bolt- () SLH-6-3/8 USS Flatwasher- () SLH-- 3/8 4-Prong T-Nut- () RFC-40 RFC-46 RFC-45 SLH-5 SLH-6 RFA-4 SLH- SLH- PG.

36 PARTS NEEDED RFC-4-3 3/4 Ladder Support- () RFC Rock Rockwall Board- (4) RFC Rock Rockwall Board- (3) RFC-8-8 Rockwall Board w/ Rope Hole- () BAB-- Rockwall Rocks- () Rainforest Cottage- Sub Assemblies SLH-- / Coated Deck Screw- (4) RWH-- /4 x /4 Pan Phillips M/S- () RWH-4- /4 USS Flatwasher- () RWH-3- /4 4- Prong T-Nut- () RFC-4 RWH- RWH-4 RFC-5 BAB- RWH-3 RFC-6 RWH-4 SLH- RWH- BAB- RWH-3 RWH- RWH-4 RFC-8 BAB- RWH-3 PG.

37 RWH-8 PARTS NEEDED RFC /8 Rockwall Support Leg- () RFC-7-8 Blank Rockwall Board- (4) RFC Rock Rockwall Board- (4) RFC Rock Rockwall Board- (3) RFC-8-8 Rockwall Board w/ Rope Hole- () RFA-4-90 Degree Ladder/ Rockwall Bracket- () Rainforest Cottage- Sub Assemblies RWH-6-3/8 4- Prong T-Nut- () RWH-7-3/8 x / Hex Bolt- () RWH-8-3/8 USS Flatwasher- () RWH-- Coated Deck Screw- (48) RFC-44 RFC-7 RFC-5 RFC-6 RFC-8 RWH-6 RFA-4 RWH-7 RWH- PG. 3

38 PARTS NEEDED RFC-- 6 Tic Tac Toe Board- () RFC-- 3 /6 Wood Roof Fan Board #- () RFC-- 7 5/8 Wood Roof Fan Board #- (4) RFC /6 Wood Roof Fan Plate- () RFC-5-5 3/6 Wood Roof Fan Bottom- () RFA-5- Tic Tac Toe Set- () Rainforest Cottage- Sub Assemblies WRH-6- / Coated Deck Screw- (8) RFC- RFC- RFA-5 RFC-36 RFC-5 WRH-6 RFC- PG. 4

39 PARTS NEEDED RFC-5-44 Swingbeam Top Joist- () RFC-5-44 Slim 4- Hole Facia- (3) RFC / Corner Post- () RFC Hole Facia- () RFC Hole Facia- () Rainforest Cottage- Swingbeam Side Wall RFH-7-3/8 x 6 Hex Bolt- () RFH-6-3/8 Bolt Cup- () RFH-3-3/8 USS Flatwasher- () RFH-- 3/8 Split Lockwasher- () RFH-4-3/8 Hex Nut- () RFH-- 3/8 Acorn Nut Plated- () RFC-5 RFC-5 RFC-56 RFC-30 RFC-5 RFC-5 5 3/4 3 / RFC-9 /8 RFH-7 RFH-9 RFH-6 RFH-9 RFH-3 RFH-4 RFH- RFH- RFH- RFH- PG. 5

40 PARTS NEEDED RFC /8 Trapeze Arm- () RFC-5-44 Slim 4- Hole Facia- () RFC Hole Facia- () RFC Corner Post- () Rainforest Cottage- Trapeze Side Wall RFH-7-3/8 x 6 Hex Bolt- () RFH-6-3/8 Bolt Cup- () RFH-3-3/8 USS Flatwasher- () RFH-- 3/8 Split Lockwasher- () RFH-4-3/8 Hex Nut- () RFH-- 3/8 Acorn Nut Plated- () RFC-53 RFC-5 RFC-9 RFC-55 RFC-9 5 3/4 RFH-7 RFH-6 RFH-9 RFH- RFH-3 RFH-4 RFH-9 RFH- RFH- RFH- PG. 6

41 Rainforest Cottage- Trapeze Side Wall PARTS NEEDED RFC /6 Trapeze Gusset- () RFC /8 Rockwall Side Runner- () RFC /8 Ladder Side Runner- () Rainforest Cottage Main Assembly RFH-0-3/8 x 3 / Hex Lag Screw- () RFH-3-3/8 USS Flatwasher- (6) RFH-6-3/8 x 4 / Hex Bolt- (4) RFH-6-3/8 Bolt Cup- (4) RFH-- 3/8 Split Lockwasher- (4) RFH-4-3/8 Nylon Insert Locknut- (4) RFH-- 3/8 Acorn Nut Plated- (4) RFH-- /4 USS Flatwasher- (8) RFH-9- /4 x 3 Hex Lag Screw- (8) RFC-50 Trapeze Side Wall RFC-34 RFC-35 Swingbeam Side Wall RFH-0 RFH-6 RFH-6 RFA- RFH- RFH-3 RFH-3 RFH-4 RFH- RFH- RFH-9 PG. 7

42 PARTS NEEDED RFC /8 Mainbeam- () RFC Center Post- () Rainforest Cottage Main Assembly RFH-6-3/8 x 4 / Hex Bolt- (6) RFH-3-3/8 USS Flatwasher- (6) RFH-5-3/8 4- Prong T-Nut- (6) RFH-- 3/8 Acorn Nut Plated- (6) RFH-9- /4 x 3 Hex Lag Screw- (0) RFH-- /4 USS Flatwasher- (0) RFC-48 RFC-54 RFC-54 RFH-5 RFH- RFH- RFH-5 RFH-6 RFH- RFH-3 RFH-9 RFH-6 RFH- RFH- RFH-3 RFH-9 RFH-9 PG. 8

43 PARTS NEEDED RFC /8 0-Hole Facia- () RFC-5-4 /8 Picnic Table Leg- () RFC /6 Outside Picnic Bench Support- () Rainforest Cottage Main Assembly RFH-- /4 USS Flatwasher- (6) RFH-9- /4 x 3 Hex Lag Screw- (6) RFC-33 RFC-5 RFC-33 RFC-39 RFH- RFH- RFH-9 RFH-9 7 3/4 PG. 9

44 PARTS NEEDED RFC-4-44 Picnic Seat Board- () RFC /6 Picnic Seat Board- () RFC-3-44 Picnic Seat Board- () Rainforest Cottage Main Assembly PTH-- / Coated Deck Screw- () PTH-3- /4 USS Flatwasher- (4) PTH-- /4 x 3 Hex Lag Screw- (4) RFC-4 RFC-4 RFC-9 RFC-4 RFC-3 PTH- PTH-3 PTH- PG. 0

45 PTH-4 PARTS NEEDED RFC-- 44 Picnic Table Board- (6) RFC-38-7 Gusset- (4) Rainforest Cottage Main Assembly PTH-- / Coated Deck Screw- (48) PTH-3- /4 USS Flatwasher- (8) PTH-- /4 x 3 Hex Lag Screw- (4) PTH-4- /4 x Hex Lag Screw- (4) RFC- RFC-38 PTH- PTH-3 PTH- PTH-3 PG.

46 PARTS NEEDED RFC-49- /8 Picnic Seat Leg- () RFC /8 Picnic Seat Bench Support- () RFC-3-44 Picnic Seat Board- () RFC-4-44 Picnic Seat Board- () Rainforest Cottage Main Assembly PTH-- /4 x 3 Hex Lag Screw- (4) PTH-3- /4 USS Flatwasher- (4) PTH-- / Coated deck Screw- () RFC-37 RFC-49 RFC-3 RFC-4 PTH- PTH-3 PTH- PG.

47 PARTS NEEDED RFC /6 Picnic Seat Board- (3) RFC-4-44 Deck Board- (6) Rainforest Cottage Main Assembly RFH-3- / Coated Deck Screw- (76) RFC-9 RFC-9 RFC-9 RFC-4 RFH-3 RFH-3 PG. 3

48 PARTS NEEDED RFC-38-7 Gusset- (0) RFC-0- Short - Hole Facia- (3) Rainforest Cottage Main Assembly RFH-9- /4 x 3 Hex Lag Screw- (6) RFH-- /4 USS Flatwasher- (6) RFH-8- /4 X / Hex Lag Screw- (0) RFC-38 RFC-38 RFC-0 RFC-0 RFC-0 RFH- RFH- RFH-9 RFH-8 RFH- RFH-9 PG. 4

49 PARTS NEEDED RFC /6 Ladder Side Rail Support Facia- () RFC-- Center Support Facia- () Rainforest Cottage Main Assembly RFH-- /4 USS Flatwasher- (6) RFH-9- /4 x 3 Hex Lag Screw- (6) RFC-6 RFC- RFH- RFH- RFH-9 RFH-9 PG. 5

50 PARTS NEEDED Rockwall Assembly- () Ladder Assembly- () Rainforest Cottage Main Assembly RWH-4- /4 USS Flatwasher- (6) RWH-5- #4 x Pan Phillips T/S- (6) SLH-4- /4 USS Flatwasher- (6) SLH-3- #4 x Pan Phillips T/S- (6) Rockwall Assembly Ladder Assembly RWH-4 RWH-5 SLH-4 SLH-3 PG. 6

51 PARTS NEEDED RFC-7-9 5/8 Rope Hole Facia- () RFC-8-9 5/8 Upper 6- Hole Facia- () Rainforest Cottage Main Assembly RFH-- /4 USS Flatwasher- () RFH-9- /4 x 3 Hex Lag Screw- () RFC-7 RFC-8 RFH- RFH- RFH-9 RFH-9 PG. 7

52 PARTS NEEDED RFC-3-9 5/8 Deck Support- () RFC-8-5 / Rail Picket- (6) Rainforest Cottage Main Assembly RFH-- 5/8 Coated Deck Screw- (43) RFC-3 RFC-8 RFH- RFH- PG. 8

53 Rainforest Cottage Open Assembly (Skip to Wood Roof for Treehouse Assembly) PARTS NEEDED RFC-8-5 / Rail Picket- (4) RFH-- 5/8 Coated Deck Screw- (5) RFC-8 RFC-8 9/6 9/6 RFH- RFH- PG. 9

54 Rainforest Cottage Open Assembly (Skip to Wood Roof for Treehouse Assembly) PARTS NEEDED RFC-8-5 / Rail Picket- (9) Tic Tac Toe- () RFH-- 5/8 Coated Deck Screw- (44) RFC-8 Tic Tac Toe 9/6 RFH- RFH- PG. 0

55 Rainforest Cottage Open Assembly (Skip to Wood Roof for Treehouse Assembly) PARTS NEEDED RFC-3-6 / Tic Tac Toe Filler Arch- () RFC-8-6 / Rail Picket- () RFH-- 5/8 Coated Deck Screw- (6) RFC-8 RFC-3 RFH- 9/6 RFH- PG.

56 PARTS NEEDED RFC Wood Roof Support- (4) RFC-- 8 3/8 Wood Roof Peak Facia- () Rainforest Cottage Wood Roof Assembly WRH-3-3/8 x 4 / Hex Bolt- (4) WRH-- 3/8 Bolt Cup- (4) WRH-- 3/8 4- Prong T-Nut- (4) WRH-0-3/8 Acorn Nut Plated- (4) WRH-5- Coated Deck Screw- (6) WRH-4- / Coated Deck Screw- (4) RFC-43 RFC-43 RFC- WRH-4 WRH-3 WRH- WRH- WRH-0 WRH-5 PG.

57 PARTS NEEDED Fan Assembly- () RFC /6 (L) Wood Roof Board- Trapeze- (4) Rainforest Cottage Wood Roof Assembly WRH-9-5/8 Coated Deck Screw- (6) Fan Assembly RFC-60 /4 WRH-9 WRH-9 PG. 3

58 PARTS NEEDED RFC-6-5 3/6 (R) Wood Roof Board- Trapeze- (4) RFC-0-5 3/6 Wood Roof Topper #- () RFC-7-5 3/6 Wood Roof Topper- () Rainforest Cottage Wood Roof Assembly WRH-9-5/8 Coated Deck Screw- (6) WRH-4- / Coated Deck Screw- (8) RFC-6 RFC-0 RFC-7 WRH-9 WRH-4 PG. 4

59 PARTS NEEDED RFC /4 Wood Roof Center Support- () RFC /6 (L) Wood Roof Board- Trapeze- (4) Rainforest Cottage Wood Roof Assembly WRH-6- / Coated Deck Screw- (8) WRH-9-5/8 Coated Deck Screw- (6) Repeat for both sides. RFC-60 RFC-3 WRH-6 WRH-6 WRH-9 PG. 5

60 Rainforest Cottage Wood Roof Assembly PARTS NEEDED RFC-6-5 3/6 (R) Wood Roof Board- Trapeze- (4) RFC Wood Roof Support- () WRH-9-5/8 Coated Deck Screw- (6) WRH-6- / Coated Deck Screw- (4) WRH-4- / Coated Deck Screw- () WRH-3-3/8 x 4 / Hex Bolt- () WRH-- 3/8 Bolt Cup- () WRH-- 3/8 4- Prong T-Nut- () WRH-0-3/8 Acorn Nut- () RFC-43 RFC-6 WRH-3 WRH-6 WRH-0 WRH- WRH-4 WRH-9 WRH- PG. 6

61 PARTS NEEDED RFC-- 8 3/8 Wood Roof Peak- () Fan Assembly- () Rainforest Cottage Wood Roof Assembly WRH-5- Coated Deck Screw- (6) WRH-9-5/8 Coated Deck Screw- (0) RFC- Fan Assembly WRH-5 WRH-9 PG. 7

62 PARTS NEEDED RFC Wood Roof Extension- () RFC-- 8 3/8 Wood Roof Peak- () Rainforest Cottage Wood Roof Assembly WRH-4- / Coated Deck Screw- () WRH-8- /4 x Hex Lag Screw- (8) WRH-7- /4 USS Flatwasher- (8) WRH-5- Coated Deck Screw- (6) Make even with the other Wood Roof Supports RFC- RFC-47 4 /8 WRH-7 WRH-4 WRH-5 WRH-8 PG. 8

63 PARTS NEEDED RFC /6 SB Side Wood Roof Board- (8) RFC-6-48 /6 Wood Roof Topper- () RFC-9-48 /6 Wood Roof Topper #- () Rainforest Cottage Wood Roof Assembly WRH-9-5/8 Coated Deck Screw- (3) WRH-4- / Coated Deck Screw- (8) RFC-59 RFC-59 RFC-6 RFC-9 WRH-9 WRH-4 PG. 9

64 PARTS NEEDED RFC /4 Wood Roof Center Support- () RFC /6 SB Side Wood Roof Board- (8) Rainforest Cottage Wood Roof Assembly WRH-6- / Coated Deck Screw- (6) WRH-9-5/8 Coated Deck Screw- (3) Repeat for both sides. Repeat for both sides. RFC-3 RFC-59 WRH-6 WRH-6 WRH-9 PG. 30

65 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFC-8-6 / Rail Picket- (4) RFH-- 5/8 Coated Deck Screw- (96) RFC-8 RFTP- RFC-8 RFH- RFH- PG. 3

66 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFC-8-6 / Rail Picket- () RFTP-5-6 / Rail Picket for Treehouse- (3) Tic Tac Toe- () RFH-- 5/8 Coated Deck Screw- () TPH-- 5/8 Coated Deck Screw- (5) RFTP-5 RFC-8 Tic Tac Toe Center and Screw Down. RFH- TPH- RFH- PG. 3

67 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFC-3-6 / Tic Tac Toe Filler Arch- () RFTP-5-6 / Rail Picket For Treehouse- () RFTP-3-6 / Panel Board- () RFH-- 5/8 Coated Deck Screw- (8) TPH-- 5/8 Coated Deck Screw- (6) RFTP-5 RFC-3 RFTP-3 TPH- RFH- PG. 33

68 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP /6 Window Arches- () RFTP-0-7 /4 Upper Panel Board- (6) RFTP-- 7 /4 Upper Panel Board for Shutters- (8) TPH-3- /4 USS Flatwasher- (8) TPH-- /4 x 3 Hex Lag Screw- (8) TPH-- 5/8 Coated Deck Screw- (56) Repeat for both sides. Repeat for both sides. RFTP-3 RFTP-0 RFTP- TPH-3 TPH- TPH- PG. 34

69 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP-9- (R) Window Shutter For Side- (4) RFTP-8- (L) Window Shutter For Side- (4) RFTP Window Top- () TPH-4-5/8 Coated Deck Screw- (64) TPH-- /4 x 3 Hex Lag Screw- (4) TPH-3- /4 USS Flatwasher- (4) Repeat for both sides. Repeat for Swingbeam side. RFTP-9 RFTP-33 RFTP-8 TPH-3 TPH- TPH- PG. 35

70 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP-6-3 /6 Corner Angle Board- () RFTP-3-6 /6 Upper Panel Board For Shutter- () RFTP-4-6 /6 Upper Panel Board for End- () TPH-- 5/8 Coated Deck Screw- (8) RFTP-4 RFTP-6 RFTP-6 RFTP-3 RFTP-3 TPH- TPH- PG. 36

71 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP-6- /4 (L) Shutter for Trapeze Side- () RFTP-7- /4 (R) Shutter for Trapeze Side- () RFTP-- 0 /6 Under Fan Board- (6) RFTP-5-0 / Under Fan Angle Cut- () TPH-- 5/8 Coated Deck Screw- (34) RFTP- RFTP-6 RFTP-7 RFTP-5 TPH- TPH- PG. 37

72 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP-9-8 /6 Panel Support- () RFTP-8-8 3/6 Corner Angle Board SB Side- () TPH-- 5/8 Coated Deck Screw- (0) RFTP-9 sits 3/4 under the top of the Fan Bottom RFTP-9 RFTP-8 RFTP-8 TPH- TPH- PG. 38

73 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP-- 4 9/6 SB Side Under Fan Center Board- () RFTP-6-3 9/6 SB Side Upper Center Board- () RFTP-5-0 / Under Fan Angle Cut- () RFTP-- 0 /6 Under Fan Board- (6) TPH-- 5/8 Coated Deck Screw- (30) RFTP- RFTP-5 RFTP- RFTP-6 TPH- TPH- PG. 39

74 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP-3-6 3/4 (L) SB Side Shutter- () RFTP-- 6 3/4 (L) SB Shutter- () RFTP-4-6 3/4 (R) SB Shutter- () RFTP-5-6 3/4 (R) SB Side Shutter- () TPH-- 5/8 Coated Deck Screw- (30) RFTP-9 sits 3/4 under the top of the Fan Bottom RFTP-3 RFTP- RFTP-4 RFTP-5 RFTP-9 TPH- TPH- PG. 40

75 7/8 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP Slim 4- Hole Facia- () RFTP Lemonade 4- Hole Facia- () TPH-- /4 x 3 Hex Lag Screw- (8) TPH-3- /4 USS Flatwasher- (8) RFTP-30 RFTP-35 TPH-3 TPH-3 TPH- TPH- PG. 4

76 TPH- Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP Lemonade Facia- () RFTP-9-44 / Lower Panel Board- () RFTP-7-6 / Lower Panel Board- () TPH-- /4 x 3 Hex Lag Screw- (4) TPH-3- /4 USS Flatwasher- (4) TPH-- 5/8 Coated Deck Screw- (56) RFTP-34 RFTP-9 4 /8 RFTP-7 TPH-3 PG. 4

77 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP-4-6 /4 Upper Lemonade Board- (3) RFTP-8-3/4 Lemonade Wood Roof Support- () TPH-- 5/8 Coated Deck Screw- (6) TPH-- /4 x 3 Hex Lag Screw- (4) TPH-3- /4 USS Flatwasher- (4) RFTP-4 RFTP-8 TPH- TPH-3 TPH- PG. 43

78 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP /4 Lemonade Wood Roof Board- () RFTP-7-8 /4 Center Wood Roof Support- () TPH-- 5/8 Coated Deck Screw- (0) RFTP-36 RFTP-7 TPH- TPH- PG. 44

79 Rainforest Cottage Treehouse Assembly (Skip if Open Assembly to Swingbeam Install) PARTS NEEDED RFTP-3-3 /4 Lemonade Stand Counter- () RFTP-0-4 /4 Lower Left Shutter- () RFTP-- 4 /4 Lower Right Shutter- () TPH-6-5/8 Coated Deck Screw- (6) RFTP-0 RFTP- RFTP-3 TPH- TPH- PG. 45

80 PARTS NEEDED RFA-5-6 Trapeze Bar with Rings- () RFA-7-0 x 00mm Spring Clip- () RFA-0-90 Degree Bracket- (6) Rainforest Cottage Accessories (For All Assemblies) RFH-5- #4 x Pan Phillips T/S- () RFH-- /4 USS Flatwasher- () RFA-5 RFA-0 RFA-7 RFH- RFH-5 PG. 46

81 PARTS NEEDED RFA-- Playgrip U-Mount Ladder Handle- () RFA-3- /4 Playgrip Safety Handle- () Rainforest Cottage Accessories (For All Assemblies) SLH-3- #4 x Pan Phillips T/S- (8) SLH-4- /4 USS Flatwasher- (8) RFH-- /4 USS Flatwasher- (4) RFH-5- #4 x Pan Phillips T/S- (4) RFA- RFA-3 SLH-3 SLH-4 RFH- RFH-5 PG. 47

82 PARTS NEEDED RFA-9- Telescope- () RFA-6- x Chalkboard Panel- () Rainforest Cottage Accessories (For All Assemblies) Hardware with Telescope- () RFH-5- #4 x Pan Phillips T/S- (4) RFH-- /4 USS Flatwasher- (4) PG. 48

83 PARTS NEEDED RFA-- Ships Wheel- () RFA-0-90 Degree Bracket- () Rainforest Cottage Accessories (For All Assemblies) Hardware with Ships Wheel- () RFH-- /4 USS Flatwasher- (4) RFH-5- #4 x Pan Phillips T/S- (4) RFA- RFA-0 RFH- RFH-5 PG. 49

84 Rainforest Cottage Accessories (For All Assemblies) PARTS NEEDED RFA-- 4 Yellow Rope- () SBL-- 7/8 A-Frame Block- () SBL-3-7/8 A-Frame Block Sinked- () SBL-- 7 5/8 Center A-Frame Block- () Rainforest Cottage Swingbeam Install SBH-7-3/8 x 0 Hex Bolt- () SBH-0-3/8 Bolt Cup- () SBH-4-3/8 USS Flatwasher- () SBH-- 3/8 Split Lockwasher- () SBH-6-3/8 Hex Nut- () SBH-- 3/8 Acorn Nut Plated- () SBL- RFA- SBH-7 SBL-0 SBL-3 SBL-4 Slide RFA- Through RFC-7 and tie a knot holding it in place. Work your way down tying a knot every to 3 feet until you string the rope through RFC- 8 and tie a knot securing the rope to the Rockwall. SBL- SBL- SBL-6 SBL- PG. 50

85 PARTS NEEDED SBL-6-3 Position Swingbeam- () RFA-- Ductile Iron Swing Hangers- (4) Rainforest Cottage Swingbeam Install SBH-8-3/8 x 7 Hex Bolt- (8) SBH-0-3/8 Bolt Cup- (9) SBH-4-3/8 USS Flatwasher- (9) SBH-- 3/8 Split Lockwasher- (9) SBH-- 3/8 Nylon Insert Locknut- (8) SBH-- 3/8 Acorn Nut Plated- (9) SBH-6-3/8 Hex Nut- () SBH-7-3/8 x 0 Hex Nut- () SBL-6 SBH-0 SBH-4 SBH- SBH-8 RFA- SBH- SBH- SBH-7 SBH-0 SBH-4 SBH- SBH- SBH-6 PG. 5

86 PARTS NEEDED SBL-5-3 A-Frame Leg- () RFA-6-45 Degree Swingbeam Bracket- () RFA-4- Swingbeam Tri-Plate- () Rainforest Cottage Swingbeam Install SBH-9- / x Hex Bolt- () SBH-5- / USS Flatwasher- (4) SBH-3- / Split Lockwasher- (3) SBH-7- / Hex Nut- (3) SBH-- / Acorn Nut Plated- (3) SBH-6-3/4 USS Flatwasher- () SBH-3- / x 3 / Carriage Bolt- () SBL-5 SBH- RFA-4 SBH-3 RFA-6 SBH-5 SBH-7 SBH-5 SBH-3 SBH-6 SBH-9 SBH-3 SBH-5 SBH-7 SBL-5 SBH- PG. 5

87 PARTS NEEDED SBL-4-68 A-Frame Crossmember- () Rainforest Cottage Swingbeam Install SBH-5- / x 9 Carriage Bolt- () SBH-4- / x 7 Carriage Bolt- (3) SBH-6-3/4 USS Flatwasher- (4) SBH-5- / USS Flatwasher- (4) SBL-4 Place the top corner of the A-FRAME CROSSMEMBER to the outside of theaframe LEG. Use a clamp or another person to hold one side while leveling. Once level and held down, use a pen/pencil to mark a hole on the A-FRAME LEGS SBH-5 SBH-7 SBH-5 SBH-4 SBH-6 SBH-3 SBH- Drill a 9/6 hole through the A-FRAME LEGS where your marks are. The holes should be slightly bigger than the bolt to allow for easy insert of the Carriage Bolt used in next step. SBH-7 SBH-3 SBH-6 SBH-4 SBH- SBH-5 PG. 53

88 Rainforest Cottage Swingbeam Install PARTS NEEDED BAB-- 66 Chained Belt Swing- () RFA-7-0 x 00mm Spring Clip- (4) SBH-0-3/8 x 5 Hex Lag Screw- () SBH-4-3/8 USS Flatwasher- () BAB- SBH-4 SBH-0 RFA-7 PG. 54

89 PARTS NEEDED RFA-8- Disc Swing- () RFA-- 4 Yellow Rope- () Rainforest Cottage Swingbeam Install Hardware with Ships Wheel- () RFH-- /4 USS Flatwasher- (4) RFH-5- #4 x Pan Phillips T/S- (4) Slip the rop throught the Swingbeam and tie a knot.. Then tie a know every 3 to 4 feet until you place the RFA-8 on the rope and tie a double knot keeping it in place. Using a 7/6 Drill Bit, Drill throught the slide and deck. Then attach as shown. RFA- Slide RFA-8 SH- SH-3 SH- PG. 55

90 PG. 56