Playful Platform 29' 29'
|
|
- Regina Greene
- 5 years ago
- Views:
Transcription
1 R PB 8270 Playful Platform TM check out for updates to these instructions. Option #1 PB 8263 Swing Beam PB 8270 Platform NE 4675L Slide 29' Option #2 PB 8263 Swing Beam PB 8270 Platform PB 8260 Tower PB 8264 Rock Wall PB 8265 Wood Roof NE 4675L Slide PAGES ' No. of Children: Up to 6 Min. Use Zone: 29' x 22' Set Dim. 12'W x 10'L x 9'H Est. Building Time: 2 hrs. (Tower only.) 29' PAGES ASSEMBLY INSTRUCTIONS 26' No. of Children: Up to 10 Min. Use Zone: 29' x 26' Set Dim. 12'W x 14'L x 10'H Est. Building Time: 2 hrs (Tower only.) Swing N Slide 1212 Barberry Drive Janesville, Wisconsin Visit our web site at: or call us at
2 R Safety Checklist for Swing-N-Slide Play Sets and Accessories Observing the following statements and warnings reduces the likelihood of serious or fatal injury Installation Safety Have You: Consulted the assembly instructions supplied with your particular model? Noted this accessory is to be used only on Swing N Slide approved designs? (Do not alter its design or add/remove components.) Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.) Using a hacksaw, cut off all protruding threaded ends of bolts and other fasteners and remove any sharp edges with a metal file as needed? Placed the equipment on level ground, not less than six feet (1.8 meters) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires? Made sure home playground equipment is not installed over concrete, asphalt, packed earth or any other hard surface? (A fall onto a hard surface can result in serious injury to the equipment user.) Verified that suspended climbing ropes, chain,or cable are secured at both ends? Consulted in assembly instructions of your particular model for minimum use zones? Followed all anchoring and shock absorbing surfacing requirements on the back of this sheet as they apply? Made sure not to allow children to use equipment until it is properly installed? Operating Safety Have You: Determined that on-site adult supervision is provided for children of all ages? Warned children the following before allowing them to use the equipment? Not to walk close to, in front of, behind or between moving items. Not to twist swing or any other accessory chains or ropes or loop them over the top support bar since this will reduce the strength of chain or rope. Not to swing empty seats or other accessories. Be sure to sit in the center of the swing seat and other accessories with full weight on the seat. Not to attach items to the playground equipment that are not specifically designed for use with the equipment such as but not limited to, jump ropes, clotheslines, pet leashes, cables and chain. They may cause a strangulation hazard. Not to use equipment in a manner other than intended. Not to get off equipment while it is in motion. Not to climb on the equipment when it is wet. Determined that only one child per planned occupant seat should be allowed on this set at one time. Determined children must be dressed appropriately for play. Avoid clothing with draw strings and loose fitting clothes which could become entangled or snagged on equipment. Determined that suspended climbing ropes, chain, or cable cannot be looped back upon itself. Read and understood the following warning regarding the use of two and four passenger lawn swings? Warning: Lawn Swings are designed for use by children over two years of age. Use by children under the age of two can result in entrapment between the seats and back areas. Never place children in a rearward facing position or with legs between the seat and backrest because the child s body may pass through the opening causing entrapment of the child s head. Safety Maintenance Have You Determined to: Check all nuts and bolts twice monthly during the usage season for tightness and tighten as required? (It is particularly important that this procedure be followed at the beginning of each season.) To prevent the deterioration of materials, remove plastic swing seats and other plastic accessories and take indoors? (Do not use when the temperature drops below 0 F.) Oil all metallic moving parts monthly during usage period? Check all hardware and equipment for sharp edges twice monthly during usage season? (Replace when necessary. It is especially important to do this at the beginning of each new season.) Check swing seats, chains, ropes and cables monthly during usage season for evidence of deterioration? Severe rusting or excessive wear, especially near the top swing hanger or at the seat connection are evidence of chain deterioration. Cracks in the protective plastic sleeve or seat itself are also signs of deterioration. If any of these conditions exist, call to order replacement accessories. Sand rusted metal parts and repaint using non-lead based paint. Disposal Instructions When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the set is discarded. Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment. Save this instruction sheet in the event the manufacturer needs to be contacted. 2
3 This product is intended for single family home/residential use only and not intended for use in any public setting. Placement in any public setting constitutes a misuse of this product. IMPORTANT! ADDITIONAL REQUIRED SAFETY INSTALLATION INSTRUCTIONS According to ASTM requirements, all kits must be anchored to the ground and, if the unit has a climbing rope, the rope end must be anchored to the ground. If soil conditions permit stakes to be pulled out easily, cementing into ground is necessary. To anchor the unit to the ground, Follow the instructions included in this plan for applying Anchor-It devices to your unit, or use 2" x 4" x 18" (45mm x 95mm x 457mm) pressuretreated stakes. Pound stakes into ground at least 12" (305mm) at all inside corners of the posts (including A-frame legs and climbing unit posts). Attach with four (4) 16D (3-1/2") galvanized nails per stake into each 4" x 4" (95mm x 95mm) post. If the unit has a climbing rope, anchor the rope end. Once the unit is completely assembled and before children are allowed to play on it, proper shock-absorbing surfacing material must be installed. This may be accomplished by using loose-fill materials at a sufficient depth. The Consumer Product Safety Commission Handbook for Public Playground Safety lists the following materials and required depths that are sufficient for home/residential application. For fall height protection up to 9 ft. (2.742m) [recommended for Swing N Slide kits]: LOOSE FILL MATERIAL REQUIRED (UNCOMPRESSED) DEPTH 1 in. (mm) Wood Mulch 9" (229mm) Double Shredded Bark Mulch 9" (229mm) Uniform Wood Chips 12" (305mm) Fine Sand 12" (305mm) Fine Gravel 12" (305mm) These depths were derived from the CPSC Handbook. Swing N Slide has not done independent tests to determine these required depths. When properly installed, shock absorbing material will completely cover the horizontal baseboards on climbing units. This protective surfacing must extend a minimum of 6 ft. (1.828m) in all directions from the perimeter of the equipment or from the outermost edges of any component. For example, a slide extending beyond the platform must have protective surfacing at least 6 ft. (1.828mm) out from both sides as well as the end. For swings, the protective surface must extend at least 14 ft. (6m) out from both the back and front of the swing when the swing is in its rest position. Notes: 3
4 TOOLS REQUIRED HERRAMIENTAS REQUERIDAS OUTILS REQUIS TOOLS REQUIRED ELECTRIC DRILL 1/2" SOCKET & WRENCH HAMMER TAPE MEASURE SAFETY GLASSES & DUST MASK PHILLIPS BIT CARPENTER'S SQUARE (2) 1/2'' Panhead Screw (16) 2'' Lag Screw (4) 3/4'' Panhead Screw (2) 1-3/4'' Panhead Screw (4) 1-1/2'' Lag Bolt (1) T20 Torx Bit (6) 1-1/4'' Wood Screw (2) 1/4'' Flat Washer (54) 2'' Wood Screw (4) 5/16'' Flat Washer (96) 2-1/2'' Wood Screw (1) T30 Torx Bit (18) 1-1/4'' Lag Screw (4) Tarp Washer 4
5 R (2) EZ Frame Brace (R) (3) 'L' Bracket (2) EZ Frame Brace (L) THIS PRODUCT IS INTENDED FOR USE BY CHILDREN FROM AGES 2-10 YEARS For Home / Residential Use ONLY 1212 Barberry Drive Janesville, WI (1) Play Handle (1) PlayfulPlatform Tarp (1) Name Plate (4) Anchor-Its (4) Anchor-It Straps Playful Platform Plan (1) Plan 5
6 Platform Board List (1) 1 x 4 x 18 (1) 1 x 4 x 19 (12) 1 x 4 x 21 (1) 1 x 4 x 24 (2) 1 x 4 x 27 Angle Cut NOM INAL M ATERIAL SIZE LISTED SIZE T RUE SIZE English(*) Metric(Cm) English(*) Metric(Cm) 1x4 2.5x7.6 3/4x3-1/2 1.9x9 1x6 2.5x15.3 3/4x5-1/2 1.9x14 5/4x4 3.2x10.2 1x3-1/2 2.5x9 5/4x6 3.2x15.3 1x5-1/2 2.5x14 2x2 5x5 1-1/2x1-1/2 3.8x3.8 2x3 5x /2x2-1/2 3.8x6.4 2x4 5x10 1-1/2x3-1/2 3.8x9 2x6 5x /2x5-1/2 3.8x14 3x3 7.6x7.6 3 x3 7.6x7.6 4x4 10x10 3-1/2x3-1/2 9x9 (*) Estimated Sizing Due to Cutting Process (1) 5/4 x 4 x 10 Angle Cut (2) 5/4 x 4 x 16 (3) 5/4 x 4 x 24 (1) 2 x 4 x 13-5/8 (2) 2 x 4 x 18 (2) 2 x 4 x 46 (4) 2 x 4 x 94 (1) 2 x 4 x 12 Slide Stake (2) 5/4 x 2-1/2 x 19 (2) 5/4 x 2-1/2 x 48 (1) 4 x 4 x 10 Angle Cut 6
7 How to select the correct fastener Use these 2 pictorial guides to help select the correct fastener(s) for the lumber attachment you are making. Each diagram will highlight the correct number of fasteners to use, and where to attach them. 1'' x 4'' to 2'' x 4'' Playful Platform Assembly Instructions (3) 2'' screws Apply 2" screws to the 1'' x 4'' boards when attaching to 2'' x 4'' uprights. 1'' x 4'' to 1'' x 4'' (2) 1-1/4'' screws Use 1-1/4'' screws when mounting 1'' x 4'' boards to 1''x4'' boards. 7
8 OPTION 1 INSTRUCTIONS Fig. 1 (3) 2'' screws Note: Screws Must Be Driven Through 5/4'' x 4'' Into The 2'' x 4''. 5/4'' x 4'' x 10'' Angle NOTE: Double check your measurements to make sure the structure is square. (3) 2'' screws 1'' x 4'' x 27'' Angle (3) 2-1/2'' screws 2'' x 4'' x 46'' 75-1/2'' 2'' x 4'' x 94'' 2'' x 4'' x 94'' 50-5/8'' 92-5/8'' Frame 1 Frame Assembly: 2'' Wood Screw 1. Install (1) 5/4'' x 4'', (1) 1'' x 4'' and (1) 2'' x 4'' boards as shown in (Fig. 1). 2-1/2'' Wood Screw 8
9 Fig. 2 NOTE: Double check your measurements to make sure the structure is square. (3) 2'' screws 1'' x 4'' x 27'' Angle (3) 2-1/2'' screws 2'' x 4'' x 46'' 75-1/2'' 2'' x 4'' x 94'' 2'' x 4'' x 94'' 50-5/8'' 92-5/8'' Frame 2 Frame Assembly Cont.: 2'' Wood Screw 1. Install (1) 1'' x 4'' and (1) 2'' x 4'' boards as shown in (Fig. 2). 2-1/2'' Wood Screw 9
10 Fig. 3 2'' x 4'' x 13-5/8'' Angle (3) 2-1/2'' screws 86'' Frame 2 Frame Assembly Cont.: 1. Install (1) 2'' x 4'' as shown in (Fig. 3). 2-1/2'' Wood Screw 10
11 Fig. 4 (3) 1-1/4'' Lag screws 3 5/8 3-5/8'' Frame 2 Swing Beam Support: 1. Install Swing Support Bracket as shown in (Fig. 4). 1-1/4'' Lag Screw 11
12 Fig. 5 (4) 2'' Lag screws per Bracket 3'' Center Brackets on 4'' x 4'' x 10'' Double check to make sure structure is square 4'' x 4'' x 10'' Angle Fig. 5a (3) 2-1/2'' wood screws 4'' x 4'' x 10'' Angle Fig. 5b (3) 1-1/4'' Lag screws UNDERSIDE VIEW Frame 2 2-1/2'' Wood Screw 2'' Lag Screw Swing Beam Support Cont.: 1. Attach (2) Swing beam Brackets as shown in (Fig. 5). 2. Secure Assembly in place on Frame as shown in (Fig. 5a). 3. Finish securing Assembly in place with 'L' Bracket as shown in (Fig. 5b). 1-1/4'' Lag Screw 12
13 DETAIL VIEW UNIT ROTATED 180 Fig. 6a (2) 2-1/2'' wood screws 5/4'' x 4'' x 24'' Double check to make sure structure is square 10-3/4'' Fig. 6 5/4'' x 4'' x 24'' 10'' 2'' x 4'' x 18'' 2'' x 4'' x 18'' (2) 2-1/2'' wood screws 10'' Frame 1 1'' x 4'' x 24'' (2) 2-1/2'' wood screws Install Frame Braces: 2-1/2'' Wood Screw 1. Install (1) 1'' x 4'', (1) 5/4'' x 4'', and (2) 2'' x 4'' boards as shown in (Fig. 6), and (Fig. 6a). 13
14 Fig. 7 (2) 2-1/2'' wood screws 2-1/2'' Wood Screw Platform Assembly: 1. Lift second half of Platform and secure in place in (4) locations as shown in (Fig. 7). 14
15 Fig. 8 (2) 2-1/2'' wood screws (12) 1'' x 4'' x 21'' NOTE: There must be a 3/8'' Nominal Gap between deck boards. Install Deck: 2-1/2'' Wood Screw 1. Install Deck boards, evenly spaced with a 3/8'' Gap, as shown in (Fig. 8). 15
16 Fig. 9 NOTE: Double check your measurements to make sure the boards are square. (2) 2-1/2'' wood screws (2) 5/4'' x 4'' x 24'' 24-1/4'' 37-3/4'' Install Step Rungs: 1. Install Step Rungs as shown in (Fig. 9). 2-1/2'' Wood Screw 16
17 Fig /2'' 92-1/2'' PB 8263 Swing Beam Hole Locations /2'' 1. Tap Wood Loc Washer and Carriage Bolt into swing beam at locations shown in (Fig. 10). 8 7/8 3 3/4 78-5/8'' 74-7/8'' Fig. 10a 101/4 3 3/4 64-5/8'' 60-7/8'' 6-1/2'' CARRIAGE BOLT 7 1/4 53-5/8'' 3'' x 5-1/2'' Swing Beam WOOD LOC WASHER 3 3/4 49-7/8'' 94'' 121/4 37-5/8'' 3 3/4 33-7/8'' 7 1/4 3 3/4 26-5/8'' 22-7/8'' 101/4 12-5/8'' 3 3/4 8-7/8'' 8-7/8'' 3-1/2'' 17
18 Fig. 11 3'' x 5-1/2'' Swing Beam WASHER LOC-NUT WASHER LOC-NUT Swing Beam Drill Locations 1. Flip 3'' x 5-1/2'' Swing Beam so Carriage Bolts point downward as shown in (Fig. 11). 2. Install the swing hanger onto the beam by sliding over two carriage bolts (refer to (Fig. 10) for placement) and apply two washers and two loc-nuts per Swing Hanger. Make certain to orient swing hanger as shown in (Fig 11). Note: When attaching D-Ring, make certain threads are pointing up. This will help keep the D-Ring from loosening over time. 3. Repeat for all four hangers. Note: Examine all hardware after the loc-nuts are fully tightened. If more than two threads are exposed, cut the excess bolt off with a hacksaw or other suitable cutting tool. 18
19 Fig /2'' FACE (8) 2-1/2 Screws A-Frame Assembly Align the edges of the 3" x 3-1/2" legs with the edges of EZ Frame Bracket 3-1/2'' FACE 3'' FACE 1. layout 3'' x 3-1/2 s and 2'' x 4'' as shown in (Fig. 12). 2. Align EZ Frame Bracket with face of 3'' x 3-1/2''s. 3. Secure EZ Frame Bracket with (8) 2-1/2'' screws to 3'' x 3-1/2''s making sure they are flush with each other. 4. Secure 2'' x 4'' to 3'' x 3-1/2''s as shown in (Fig. 12a). 5. Flip over and add 2nd bracket. Repeat steps 2 and 3. Fig. 12a EZ Frame Bracket 3" x 3-1/2" x 94'' 3" x 3-1/2" x 94'' (4) 2-1/2'' screws (4) 2-1/2'' screws 2" x 4" x 47-1/2" 3-1/2'' FACE 49-1/2" 92-5/8" 2-1/2'' screw 19
20 Fig. 13 Washer 2-1/2'' screws Loc-Nut 2-1/2'' screw A-Frame Assembly cont. 1. Align EZ-Frame Bracket with carriage bolts on Swing Beam as shown in (Fig. 13). 2. Attach A-Frame beam to Swing Beam using (2) washers and (2) Loc-Nuts and (2) screws as shown in (Fig. 13). 3. Tighten Loc-Nut. Repeat on other bracket. Note: Examine all hardware after the loc-nuts are fully tightened. If more than two threads are exposed, cut the excess bolt off with a hacksaw or other suitable cutting tool. 20
21 A-Frame Assembly cont. 1. With the help of others, lift A-Frame and Swing Beam Assembly and center onto unit as shown in (Fig. 14). 2. Secure Swing Beam with Hardware shown in (Fig. 14a). Fig. 14 Swing Beam Fig. 14a Swing Beam View from Deck 2'' Lag screw x 4 (each bracket) 21
22 Fig. 15 (4) 2'' Lag Screws AND (4) 2'' wood screws per Brace (2) Braces per side of unit Install EZ-Frame Braces: 2'' Wood Screw 1. Install (2) EZ-Frame Braces per side of the units as shown in (Fig. 15). 2'' Lag Screw 22
23 22-1/2'' Playful Platform Assembly Instructions Fig. 16 Double check to make sure boards are square 5/4'' x 2-1/2'' x 48'' 5/4'' x 2-1/2'' x 48'' (2) 2'' wood screws per side FLUSH Secure Tarp Supports: 1. Secure Tarp Supports as shown in (Fig. 16). 2'' Wood Screw 23
24 (2) 2'' wood screws Fig. 17 5/4'' x 2-1/2'' x 19'' (2) 2'' wood screws 5/4'' x 2-1/2'' x 19'' Tarp Support Installation Cont.: 2'' Wood Screw 1. Install Tarp support Cross Braces as shown in (Fig. 17). 24
25 22-1/4'' Playful Platform Assembly Instructions Fig. 18 (2) 5/4'' x 4'' x 16'' (2) 2'' wood screws Double check to make sure boards are square 22-1/4'' Fig. 18a (2) 2'' wood screws 1'' x 4'' x 19'' Tarp Support Braces Cont.: 1. Install Vertical Tarp Supports and Cross Brace as shown in (Fig. 18) and (Fig. 18a). 2'' Wood Screw 25
26 Fig. 19a Fig. 19 Washer 3/4'' Screw 2 Per Side Fig. 19b 1'' x 4'' x 18'' (4) 1-1/4'' wood screws Secure Tarp and Slide Support: 1-1/4'' Wood Screw 1. Secure Tarp in Place as shown in (Fig. 19), and (Fig. 19a). 2. Secure Slide Support in place as shown in (Fig. 19b). 3/4'' screw 26
27 Slide Installation. 1. Install Slide centered in the provided opening as shown in (Fig. 20). 2. Attach Stake to end of slide as shown in (Fig. 20a). Fig. 20 Fig. 20a (2) 1-1/4'' screws 2'' x 4'' x 12'' 2'' Above Ground 1'' Truss Screw Use truss head screws to to secure slide to deck. Anchor-It Fig. 21 metal strap Flat Washer 1-1/2" lag bolt Anchor-It Installation. Instructions for Anchoring Swing N Slide Activity Centers 1. Determine the final location of your activity center. 2. Place the Anchor-It stakes adjacent to the base and near the corners of your activity center (at the bottom of the legs on swing sets) and twist the auger-style stakes into the ground until only the loop is exposed. 3. Place the metal strap through the loop of the Anchor-It stake and secure it to the unit with a lag screw and washer as illustrated to the right. Note: Attach the strap to the unit with as little play as possible using whatever holes in the strap that work best. Anchor-It 27
28 R Playful Platform Assembly Instructions Fig /4'' Screw THIS PRODUCT IS INTENDED FOR USE BY CHILDREN FROM AGES 2-10 YEARS For Home / Residential Use ONLY 1212 Barberry Drive Janesville, WI www ID TAG: 1. Secure your product ID tag onto easy to read location of any 4'' x 4'' using (2) 1-1/2'' screws as shown in (Fig. 22). Safety Handle Fig. 22a Safety Handle: 1. Mount safety handle in the climber openings approximately 11'' above the deck surface (Fig. 22a). 1-3/4 Panhead screw washer 11" Deck Surface 1-3/4 Panhead screw 28
29 OPTION 2 INSTRUCTIONS Fig. 1 (3) 2'' screws Note: Screws Must Be Driven Through 5/4'' x 4'' Into The 2'' x 4''. (3) 2'' screws 5/4'' x 4'' x 10'' Angle 1'' x 4'' x 27'' Angle NOTE: Double check your measurements to make sure the structure is square. (3) 2-1/2'' screws 2'' x 4'' x 46'' 75-1/2'' 2'' x 4'' x 94'' 2'' x 4'' x 94'' 50-5/8'' 92-5/8'' Frame 1 Frame Assembly: 2'' Wood Screw 1. Install (1) 5/4'' x 4'', (1) 1'' x 4'' and (1) 2'' x 4'' boards as shown in (Fig. 1). 2-1/2'' Wood Screw 29
30 NOTE: Double check your measurements to make sure the structure is square. Fig. 2 (3) 2'' screws 1'' x 4'' x 27'' Angle (3) 2-1/2'' screws 2'' x 4'' x 46'' 75-1/2'' 2'' x 4'' x 94'' 2'' x 4'' x 94'' 50-5/8'' 92-5/8'' Frame 2 Frame Assembly Cont.: 1. Install (1) 1'' x 4'' and (1) 2'' x 4'' boards as shown in (Fig. 2). 2'' Wood Screw 2-1/2'' Wood Screw 30
31 Fig. 3 2'' x 4'' x 13-5/8'' Angle (3) 2-1/2'' screws 86'' Frame 2 Frame Assembly Cont.: 1. Install (1) 2'' x 4'' as shown in (Fig. 3). 2-1/2'' Wood Screw 31
32 Fig. 4 (3) 1-1/4'' Lag screws 3 5/8 3-5/8'' Frame 2 Swing Beam Support: 1. Install Swing Support Bracket as shown in (Fig. 4). 1-1/4'' Lag Screw 32
33 Fig. 5 3'' (3) 1-1/4'' Lag screws per Bracket 4'' x 4'' x 10'' Angle Fig. 5a (3) 2-1/2'' wood screws 4'' x 4'' x 10'' Angle Fig. 5b (3) 1-1/4'' Lag screws UNDERSIDE VIEW Frame 2 Swing Beam Support Cont.: 2-1/2'' Wood Screw 1. Attach (2) L Brackets as shown in (Fig. 5). 2. Secure Assembly in place on Frame as shown in (Fig. 5a). 3. Finish securing Assembly in place with Metal Bracket as shown in (Fig. 5b). 1-1/4'' Lag Screw 33
34 DETAIL VIEW UNIT ROTATED 180 (2) 2-1/2'' wood screws 5/4'' x 4'' x 24'' Fig. 6a Double check to make sure structure is square Fig /4'' 5/4'' x 4'' x 24'' 10'' 2'' x 4'' x 18'' 2'' x 4'' x 18'' 10'' (2) 2-1/2'' wood screws Frame 1 (2) 2-1/2'' wood screws 1'' x 4'' x 24'' Install Frame Braces: 2-1/2'' Wood Screw 1. Install (1) 1'' x 4'', (1) 5/4'' x 4'', and (2) 2'' x 4'' boards as shown in (Fig. 6), and (Fig. 6a). 34
35 Fig. 7 (2) 2-1/2'' wood screws Platform Assembly: 2-1/2'' Wood Screw 1. Lift second half of Platform and secure in place in (4) locations as shown in (Fig. 7). 35
36 Fig. 8 (2) 2-1/2'' wood screws (12) 1'' x 4'' x 21'' NOTE: There must be a 3/8'' Nominal Gap between deck boards. Install Deck: 2-1/2'' Wood Screw 1. Install Deck boards, evenly spaced with a 3/8'' Gap, as shown in (Fig. 8). 36
37 Fig. 9 NOTE: Double check your measurements to make sure the boards are square. (2) 2-1/2'' wood screws (2) 5/4'' x 4'' x 24'' 24-1/4'' 37-3/4'' Install Step Rungs: 1. Install Step Rungs as shown in (Fig. 9). 2-1/2'' Wood Screw 37
38 Fig. 10 Remove Existing A-Frame: 1. IF You already have the A-Frame on your Tower Swing Beam assembled, remove it along with the (2) E-Z Frame Brackets attached. Support the Swing Beam with a Ladder or with the help of an assistant until the Playful Platform can be manueverd in place. 38
39 Swing Beam Attachment cont. 1. With the help of others, position Swing Beam on Brackets and center onto unit as shown in (Fig. 11). 2. Secure as shown in (Fig 11a). Fig. 11 Swing Beam Fig. 11a Swing Beam View from Deck 1-1/4'' Lag Screw x 3 (each bracket) 39
40 Fig. 12 (4) 2'' Lag Screws AND (4) 2'' wood screws per Brace (1) Brace per side of unit Install EZ-Frame Braces: 2'' Wood Screw 1. Install (1) EZ-Frame Braces per side of the units as shown in (Fig. 12). 2'' Lag Screw 40
41 22-1/2'' Playful Platform Assembly Instructions Fig. 13 Double check to make sure boards are square 5/4'' x 2-1/2'' x 48'' 5/4'' x 2-1/2'' x 48'' FLUSH (2) 2'' wood screws per side Secure Tarp Supports: 1. Secure Tarp Supports as shown in (Fig. 13). 2'' Wood Screw 41
42 Fig. 14 (2) 2'' wood screws 5/4'' x 2-1/2'' x 19'' 5/4'' x 2-1/2'' x 19'' (2) 2'' wood screws Tarp Support Installation Cont.: 1. Install Tarp support Cross Braces as shown in (Fig. 14). 2'' Wood Screw 42
43 22-1/4'' 22-1/4'' Playful Platform Assembly Instructions Fig. 15 Double check to make sure boards are square (2) 5/4'' x 4'' x 16'' (2) 2'' wood screws Tarp Support Braces Cont.: 2'' Wood Screw 1. Install Vertical Tarp Supports as shown in (Fig. 15). 43
44 Fig. 16 (2) 2'' wood screws 1'' x 4'' x 19'' Tarp Support Braces Cont.: 1. Install Tarp Cross Brace as shown in (Fig. 16). 2'' Wood Screw 44
45 Fig. 17a Fig. 17 Washer 3/4'' Screw 2 Per Side Secure Tarp: 1. Secure Tarp in Place as shown in (Fig. 17), and (Fig. 17a). 3/4'' screw 45
46 Fig. 18 1'' x 4'' x 18'' (4) 1-1/4'' wood screws Secure Deck Support: 1. Secure 1'' x 4'' x 18'' Deck Support Board under the Platform Deck as shown in (Fig. 18). 1-1/4'' Wood Screw 46
47 2'' x 4'' x 56-3/4'' 2'' x 4'' x 56-3/4'' Playful Platform Assembly Instructions THESE INSTRUCTIONS SUPERCEDE THE PLAN INCLUDED WITH YOUR ROCK WALL KIT Fig. 19 Fig. 19a (16) 1'' x 4'' x 24'' (2) 2-1/2'' screws 3/4'' 21'' 1-1/2'' (2) 2-1/2'' screws (2) 2-1/2'' screws Rock Wall Assembly and Installation: 1. Assemble Rock as shown in (Fig. 19). 2. Install Rock wall on Unit as shown in (Fig. 19a). 2-1/2'' Wood Screw 47
48 Fig. 20 Hold (rock) (2)"T" nuts Climbing Rock Installation 1. Mark locations of Climbing Rocks on the Climbing Wall in a pattern that will easily allow your child to climb to the deck. Make sure the bolt hole locations are clear of wall supports before drilling. 2. Drill holes through the wall at the desired locations using a 3/8" drill bit. Install Climbing Rocks as shown in (Fig. 20). 3. Make sure the Climbing Wall and Climbing Rock connections are secure before allowing any children to play on the Climbing Wall. 3/8" Holes (2) 1-1/4'' Hex Head Bolts (1) Loc Washer per bolt (1) Flat Washer per bolt Fig. 21 metal strap Flat Washer 1-1/2" lag bolt Anchor-It Anchor-It Installation. Instructions for Anchoring Swing N Slide Activity Centers 1. Determine the final location of your activity center. 2. Place the Anchor-It stakes adjacent to the base and near the corners of your activity center (at the bottom of the legs on swing sets) and twist the auger-style stakes into the ground until only the loop is exposed. 3. Place the metal strap through the loop of the Anchor-It stake and secure it to the unit with a lag screw and washer as illustrated to the right. Note: Attach the strap to the unit with as little play as possible using whatever holes in the strap that work best. Anchor-It 48
49 R Playful Platform Assembly Instructions Fig /4'' Screw THIS PRODUCT IS INTENDED FOR USE BY CHILDREN FROM AGES 2-10 YEARS For Home / Residential Use ONLY 1212 Barberry Drive Janesville, WI www ID TAG: 1. Secure your product ID tag onto easy to read location of any 4'' x 4'' using (2) 1-1/2'' screws as shown in (Fig. 22). Safety Handle Fig. 22a Safety Handle: 1. Mount safety handle in the climber openings approximately 11'' above the deck surface (Fig. 22a). 1-3/4 Panhead screw washer 11" Deck Surface 1-3/4 Panhead screw 49
50 50
51 51
52 Questions???... Call our Customer Service Department at R PlayCore Inc Printed In USA LA 6046
53 PB 8263 Swing Beam Kit check out for updates to these instructions For more information, visit this link: 28' Minimum Safe Use Zone ASSEMBLY INSTRUCTIONS Swing N Slide 1212 Barberry Drive Janesville, Wisconsin Visit our web site at: or call us at
54 R Safety Checklist for Swing-N-Slide Play Sets and Accessories Observing the following statements and warnings reduces the likelihood of serious or fatal injury Installation Safety Have You: Consulted the assembly instructions supplied with your particular model? Noted this accessory is to be used only on Swing N Slide approved designs? (Do not alter its design or add/remove components.) Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.) Using a hacksaw, cut off all protruding threaded ends of bolts and other fasteners and remove any sharp edges with a metal file as needed? Placed the equipment on level ground, not less than six feet (1.8 meters) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires? Made sure home playground equipment is not installed over concrete, asphalt, packed earth or any other hard surface? (A fall onto a hard surface can result in serious injury to the equipment user.) Verified that suspended climbing ropes, chain,or cable are secured at both ends? Consulted in assembly instructions of your particular model for minimum use zones? Followed all anchoring and shock absorbing surfacing requirements on the back of this sheet as they apply? Made sure not to allow children to use equipment until it is properly installed? Operating Safety Have You: Determined that on-site adult supervision is provided for children of all ages? Warned children the following before allowing them to use the equipment? Not to walk close to, in front of, behind or between moving items. Not to twist swing or any other accessory chains or ropes or loop them over the top support bar since this will reduce the strength of chain or rope. Not to swing empty seats or other accessories. Be sure to sit in the center of the swing seat and other accessories with full weight on the seat. Not to attach items to the playground equipment that are not specifically designed for use with the equipment such as but not limited to, jump ropes, clotheslines, pet leashes, cables and chain. They may cause a strangulation hazard. Not to use equipment in a manner other than intended. Not to get off equipment while it is in motion. Not to climb on the equipment when it is wet. Determined that only one child per planned occupant seat should be allowed on this set at one time. Determined children must be dressed appropriately for play. Avoid clothing with draw strings and loose fitting clothes which could become entangled or snagged on equipment. Determined that suspended climbing ropes, chain, or cable cannot be looped back upon itself. Read and understood the following warning regarding the use of two and four passenger lawn swings? Warning: Lawn Swings are designed for use by children over two years of age. Use by children under the age of two can result in entrapment between the seats and back areas. Never place children in a rearward facing position or with legs between the seat and backrest because the child s body may pass through the opening causing entrapment of the child s head. Safety Maintenance Have You Determined to: Check all nuts and bolts twice monthly during the usage season for tightness and tighten as required? (It is particularly important that this procedure be followed at the beginning of each season.) To prevent the deterioration of materials, remove plastic swing seats and other plastic accessories and take indoors? (Do not use when the temperature drops below 0 F.) Oil all metallic moving parts monthly during usage period? Check all hardware and equipment for sharp edges twice monthly during usage season? (Replace when necessary. It is especially important to do this at the beginning of each new season.) Check swing seats, chains, ropes and cables monthly during usage season for evidence of deterioration? Severe rusting or excessive wear, especially near the top swing hanger or at the seat connection are evidence of chain deterioration. Cracks in the protective plastic sleeve or seat itself are also signs of deterioration. If any of these conditions exist, call to order replacement accessories. Sand rusted metal parts and repaint using non-lead based paint. Disposal Instructions When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the set is discarded. Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment. Save this instruction sheet in the event the manufacturer needs to be contacted. 2
55 This product is intended for single family home/residential use only and not intended for use in any public setting. Placement in any public setting constitutes a misuse of this product. IMPORTANT! ADDITIONAL REQUIRED SAFETY INSTALLATION INSTRUCTIONS According to ASTM requirements, all kits must be anchored to the ground and, if the unit has a climbing rope, the rope end must be anchored to the ground. If soil conditions permit stakes to be pulled out easily, cementing into ground is necessary. To anchor the unit to the ground, Follow the instructions included in this plan for applying Anchor-It devices to your unit, or use 2" x 4" x 18" (45mm x 95mm x 457mm) pressuretreated stakes. Pound stakes into ground at least 12" (305mm) at all inside corners of the posts (including A-frame legs and climbing unit posts). Attach with four (4) 16D (3-1/2") galvanized nails per stake into each 4" x 4" (95mm x 95mm) post. If the unit has a climbing rope, anchor the rope end. Once the unit is completely assembled and before children are allowed to play on it, proper shock-absorbing surfacing material must be installed. This may be accomplished by using loose-fill materials at a sufficient depth. The Consumer Product Safety Commission Handbook for Public Playground Safety lists the following materials and required depths that are sufficient for home/residential application. For fall height protection up to 9 ft. (2.742m) [recommended for Swing N Slide kits]: LOOSE FILL MATERIAL REQUIRED (UNCOMPRESSED) DEPTH 1 in. (mm) Wood Mulch 9" (229mm) Double Shredded Bark Mulch 9" (229mm) Uniform Wood Chips 12" (305mm) Fine Sand 12" (305mm) Fine Gravel 12" (305mm) These depths were derived from the CPSC Handbook. Swing N Slide has not done independent tests to determine these required depths. When properly installed, shock absorbing material will completely cover the horizontal baseboards on climbing units. This protective surfacing must extend a minimum of 6 ft. (1.828m) in all directions from the perimeter of the equipment or from the outermost edges of any component. For example, a slide extending beyond the platform must have protective surfacing at least 6 ft. (1.828mm) out from both sides as well as the end. For swings, the protective surface must extend at least 14 ft. (6m) out from both the back and front of the swing when the swing is in its rest position. NOTES: 3
56 TOOLS REQUIRED TAPE MEASURE HAMMER CARPENTER'S SQUARE ELECTRIC DRILL (1) T20 & T30 Torx Bit SAFETY GLASSES & DUST MASK (2) Split Beam bracket (2) Wrap-Loc (2) 3X3 TO 4X4 Shelf-Loc (2) EZ Frame Brackets (28) 2-1/2'' screws (28) 2" lag screw (2) 5/16''Hex Head Lag Screws (14) 6-1/2'' Bolts (14) 5/16'' flat washers (14) Loc-Nuts (14) Wood Loc Washers 4
57 Swing Beam Assembly Instructions BOARD LIST (1) 2'' x 4'' x 47-1/2'' (1) 4'' x 4'' x 47-1/2'' (2) 3'' x 3-1/2'' x 94'' (1) 3'' x 5-1/2'' x 94'' (1) Ring-Trap Combo (2) Extra Duty-Swing Seats (6) Extra-Duty Swing Hangers Swing Beam Plan (2) Anchor-It Straps (2) Anchor-It (1) Plan 5
58 Swing Beam Assembly Instructions Fig. 1 Fig /2'' (1) 2'' Lag Screws Per Bracket 84-1/2'' (2) 2'' Lag Screws Per Bracket Fig. 2a (2) 2'' Lag Screws Tip: Flex brackets to make installation of 4'' x 4'' easier Fig.2b Approx. 1/4'' Fig. 3 (5) 2'' Lag Screws Per Bracket 4" x 4" x 47-1/2" A. Swing Beam Support 1. Attach the Swing Beam Kit on the side of the tower illustrated in (Fig. 1). Make certain you have provided for the Minimum Safe Use Zone. 2. Attach Wrap Brackets to Uprights as shown in (Fig. 1). Use only one (1) 2'' Lag Screw to hold bracket in place. 3. AttachShelf Brackets to Wrap Brackets as shown in (Fig. 2). Use only two (2) 2'' Lag Screws to attach brackets as shown in (Fig. 2a). 4. Spread open Shelf Brackets as shown in (Fig. 2b). Slide 4'' x 4'' into brackets and secure as shown in (Fig. 3). 2'' Lag screw 6
59 Swing Beam Assembly Instructions Fig. 4 A-FRAME 1-1/2'' 92-1/2'' B. Swing Beam Hole Locations /2'' 1. Tap Wood Loc Washer and Carriage Bolt into swing beam at locations shown in (Fig. 4a). 8 7/8 3 3/4 78-5/8'' 74-7/8'' 101/4 3 3/4 64-5/8'' 60-7/8'' Fig. 4a 7 1/4 53-5/8'' 6-1/2'' CARRIAGE BOLT 3 3/4 49-7/8'' 94'' WOOD LOC WASHER 121/4 3'' x 5-1/2'' Swing Beam 37-5/8'' 3 3/4 33-7/8'' 7 1/4 3 3/4 26-5/8'' 22-7/8'' 101/4 12-5/8'' 3 3/4 8-7/8'' 8-7/8'' 3'' 3-1/2'' 7
60 Swing Beam Assembly Instructions Fig. 5 4'' x 6'' Swing Beam WASHER LOC-NUT WASHER D-RINGS LOC-NUT C. Swing Beam Drill Locations 1. Flip 3'' x 5-1/2'' Swing Beam so Carriage Bolts point downward as shown in (Fig. 5). 2. Install the swing hanger onto the beam by sliding over two carriage bolts (refer to (Fig. 4) for placement) and apply two washers and two loc-nuts per Swing Hanger. Make certain to orient swing hanger as shown in (Fig 5). Note: When attaching D-Ring, make certain threads are pointing up. This will help keep the D-Ring from loosening over time. 4. Repeat for all six hangers. 8
61 Swing Beam Assembly Instructions Fig /2'' FACE (8) 2-1/2 Screws D. A-Frame Assembly Align the edges of the 3" x 3-1/2" legs with the edges of EZ Frame Bracket 3-1/2'' FACE 3'' FACE 1. layout 3'' x 3-1/2 s and 2'' x 4'' as shown in (Fig. 6). 2. Align EZ Frame Bracket with face of 3'' x 3-1/2''s. 3. Secure EZ Frame Bracket with (8) 2-1/2'' screws to 3'' x 3-1/2''s making sure they are flush with each other. 4. Secure 2'' x 4'' to 3'' x 3-1/2''s as shown in (Fig. 6a). 5. Flip over and add 2nd bracket. Repeat steps 2 and 3. Fig. 6a EZ Frame Bracket 3" x 3-1/2" x 94'' 3" x 3-1/2" x 94'' (4) 2-1/2'' screws (4) 2-1/2'' screws 2" x 4" x 47-1/2" 3-1/2'' FACE 49-1/2" 93" 2-1/2'' screw 9
62 Swing Beam Assembly Instructions Fig. 7 Washer 2-1/2'' screws Loc-Nut 2-1/2'' screw E. A-Frame Assembly cont. 1. Align EZ-Frame Bracket with carriage bolts on Swing Beam as shown in (Fig. 7). 2. Attach A-Frame beam to Swing Beam using (2) washers and (2) Loc-Nuts and 2 screws as shown in (Fig. 7). 3. Tighten Loc-Nut. Repeat on other bracket. 10
63 Swing Beam Assembly Instructions F. A-Frame Assembly cont. Fig Position Split-Brackets on 4'' x 4'' x 47-1/2'' as shown in (Fig. 8). 2. With the help of others, lift A-Frame and Swing Beam Assembly and center onto unit as shown in (Fig. 8a). 3. Secure as shown in (Fig 8a). Swing Beam 22'' Fig. 8a Swing Beam View from Deck 2'' Lag screw x 8 (each bracket) 11
64 Swing Beam Assembly Instructions Fig. 9 G. Attach Swings onto Swing Hangers 1. Attach the end link of each Swing Chain to one Swing Hanger D Ring as shown in (Fig. 9). Make certain to secure each D Ring in the closed position by using an adjustable wrench. 12
65 Swing Beam Assembly Instructions Fig. 10 Fig. 11 H. Install Anchor-Its 1. (1) Anchor-It must be installed on each leg of the Swing Beam. 2. Screw a Anchor-It into the ground near each leg until only the triangular head remains as shown in (Fig. 10) and (Fig. 11). 3. Insert a strap through the head of theanchor-it. Align holes of strap as illustrated and attach to the unit using one 1-1/2" lag bolt and washer per Anchor-It. 13
66 Swing Beam Assembly Instructions 14
67 15 Swing Beam Assembly Instructions
68 Questions???... Call our Customer Service Department at PlayCore Inc Printed In USA LA 5870
69 R PB 8285 check out for updates to these instructions. Kit Components: PB 8263 Swing Beam PB 8270 Platform NE 4700-T Slide Assembly Instructions: PAGES ' NOTE: PAGES DO NOT APPLY TO THE PB 8285 DESIGN 22' No. of Children: Up to 6 Min. Use Zone: 29' x 22' Set Dim. 12'W x 10'L x 9'H Est. Building Time: 2 hrs. (Tower only.) ASSEMBLY INSTRUCTIONS Swing N Slide 1212 Barberry Drive Janesville, Wisconsin Visit our web site at: or call us at PlayCore Inc Printed In USA LA 6084
70 Assembly Instructions NOTE: THESE SLIDE INSTRUCTIONS REPLACE THOSE ON PAGE 27 OF YOUR ASSEMBLY PLAN. Fig. 20 Fig. 20a Fig. 20b (22) 5/16'' loc-nut (44) 5/16'' flat washers Fig. 20c (2) 1-1/4'' screws 2'' x 4'' x 12'' 2'' Above Ground Summit Slide Installation. 1. Align Summit slide sections together on the ground. Begin attaching two Summit slide sections together by securing the two outer most bolts in place finger tight (see (Fig. 20a) for proper Bolt Sequence). Following this pattern install (1) bolt, (2) washers and (1) loc-nut per hole (see (Fig. 20b)). Once all (11) bolts, (22) flat washers and (11) loc-nuts are in place go back and tighten all hardware with appropriate tools. 2. Consult (Fig. 20) For proper placement of Summit slide on your unit. 3. Drive wood stake into ground leaving 2'' exposed. 4. Secure the Summit slide bottom to the stake using (2) 1-1/4'' deck screws. (Fig. 20C). 5. Attach Summit slide to unit as shown in (Fig. 20). PlayCore Inc Printed In USA LA
Chesapeake TM PB 8243 ASSEMBLY INSTRUCTIONS
PB 8243 Chesapeake TM check out http://www.swing-n-slide.com/planupdates.html for updates to these instructions For more information, visit this link: http://www.swing-n-slide.com 28'-6'' 26'-6'' No. of
More informationSwing Beam Kit PB 8263 ASSEMBLY INSTRUCTIONS
PB 8263 Swing Beam Kit check out http://www.swing-n-slide.com/planupdates.html for updates to these instructions For more information, visit this link: http://www.swing-n-slide.com 28' Minimum Safe Use
More informationSafety Guidelines and Assembly Instructions
Play Action Air Rider TM Safety Guidelines and Assembly Instructions Maximum Weight Limit: 210 pounds We re Here To Help! Call Toll Free 1-888-752-9782 Customer Service: Monday - Friday, 8:00 A.M. to 5:00
More informationIMPORTANT!! ASSEMBLY INSTRUCTIONS
PB 8137 ASSEMBLY INSTRUCTIONS! WARNING: Assembly by an adult. IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are
More informationPB 5207 PB 6207 ASSEMBLY INSTRUCTIONS. Warning: Do not allow children on the playset until is has been completely built and properly anchored
R PB 5207 PB 6207 Warning: Do not allow children on the playset until is has been completely built and properly anchored ASSEMBLY INSTRUCTIONS Swing N Slide 1212 Barberry Drive Janesville, Wisconsin 53545
More informationIMPORTANT!! ASSEMBLY INSTRUCTIONS
NE 4275-4 PB 8210-4! WARNING: Assembly by an adult. No. of children: Up to 12 Est. building Time: 6-11 hrs. Two Adults IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware
More informationOwner s Manual and Assembly Instruction
Owner s Manual and Assembly Instruction Model #: 22-PS120 Model Name: Verona III Swing Set Manual Date: September, 2007 Important: Keep this owner s manual; do not discard in case you need to contact Pacific
More informationExtreme Tube Slide - 5ft.
Extreme Tube Slide - 5ft. Part Number: 03-0014 Revison: A 6.12.2013 Please inspect and inventory all parts immediately upon accepting delivery. Use the inventory pages in the manual to make sure you have
More informationMODEL PS10CLATL ASSEMbLy MAnuAL
Assembly Manual By If you have problems or questions about your Creative Playthings Play Set, DO NOT CALL THE RETAILER. Contact Creative Playthings Customer Service at 1-800-833-4001 or customerservice@creativeplaythings.com
More informationMODEL PS10CLASB ASSEMBLy MAnuAL
Assembly Manual By If you have problems or questions about your Creative Playthings Play Set, DO NOT CALL THE RETAILER. Contact Creative Playthings Customer Service at 1-800-833-4001 or customerservice@creativeplaythings.com
More informationBackyard Circus Club
Backyard Circus Club Assembly Instructions 5-70-0299 (Rev 0-12.15.11) Contains Assembly, Use, and Maintenance Instructions NOTICE: This product is intended for outdoor family domestic use only with children
More informationExtreme Tube Slide II - 5ft. Part Number: Revison D: LA 9459
Extreme Tube Slide II - 5ft. Part Number: 03-0020 Revison D: 6.19.2018 LA 9459 Please inspect and inventory all parts immediately upon accepting delivery. Use the inventory pages in the manual to make
More informationSafety Guide & Building Instructions
Safety Guide & Building Instructions TM PS 73201 PS 73202 PS 73203 PS 73204 We re Here To Help! Call Toll Free 1-888-752-9782 Customer Service: Monday - Friday, 8:00 A.M. to 5:00 P.M. C.S.T. SAFETY This
More informationMODEL PS10FRA. Model PS10FRA with. Top Ladder. Model PS10FRA with. Swing Beam
Manual By Model PS10FRA with Top Ladder Model PS10FRA with Swing Beam If you have problems or questions about your Creative Playthings Playset, DO NOT CALL THE RETAILER. Contact Creative Playthings Customer
More informationMERRY GO ROUND ITEM NO: 8030
MERRY GO ROUND ITEM NO: 8030 OWNER S MANUAL CAUTION: This unit is designed to be used safely by up to 4 children between the ages of 3 years to 8 years old with a maximum weight of 00 pounds (45.4 kgs)
More informationDO NOT CALL THE RETAILER.
Assembly Manual By Model PS10AND with Top Ladder Model PS10AND with Swing Beam If you have problems or questions about your Creative Playthings Playset, DO NOT CALL THE RETAILER. Contact Creative Playthings
More informationPlay House 5 & 6 Assembly Instructions
Play House 5 & 6 Assembly Instructions 2101 Harrod Street Raleigh, NC 27604 800/982-1822 919/875-4499 Fax 919/875-4264 PA-MAN-PHB-00 2011 Woodplay. All rights reserved. I N T R O D U C T I O N Welcome
More informationF 8:00 AM 6:00 PM EST 8:30 AM 4:30 PM EST
2692 - NOTICE - This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO
More informationATTENTION! IMPORTANT! This manual supersedes Manual 2692 in the Base Kit.
2999 ATTENTION! IMPORTANT! This manual supersedes Manual 2692 in the Base Kit. (This page intentionally left blank.) 2999 - NOTICE - This playset product is not intended for public use. It is intended
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationPB 8328 WS 8328 IMPORTANT!! JAMBOREE
PB 8328 WS 8328 JAMBOREE IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN
More information9 Station Swing Set User Manual
9 Station Swing Set User Manual For model: P9-SS Assembly, Installation, Care, Maintenance, and User Instructions WARNING READ THESE MATERIALS PRIOR TO ASSEMBLING AND USING THIS SWING SET. Failure to assemble
More informationATTENTION! IMPORTANT! If you have the Fort and Terrace options this manual supersedes Manual 2692 in the Base Kit.
2998 ATTENTION! IMPORTANT! If you have the Fort and Terrace options this manual supersedes Manual 2692 in the Base Kit. (This page intentionally left blank.) 2998 - NOTICE - This playset product is not
More informationSTOP! Call Us First! DO NOT RETURN TO STORE.
2985 - NOTICE - This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO
More informationplaysets Tire Swing Station ASSEMBLY MANUAL Copyright 2012 Gorilla Playsets All Rights Reserved
playsets Tire Swing Station ASSEMBLY MANUAL Copyright 2012 Gorilla Playsets All Rights Reserved Gorilla Playsets 190 Etowah Industrial Court Canton, GA 30114 (800) 882-0272 www.gorillaplaysets.com Latest
More informationRocketship Clubhouse
Rocketship Clubhouse Assembly Instructions 5-70-0278 (Rev 0-10.25.11) Contains Assembly, Use, and Maintenance Instructions NOTICE: This product is intended for outdoor family domestic use only with children
More informationCreating Childhood Memories Owners & Instruction Manual
R Creating Childhood Memories Owners & Instruction Manual Dream This instruction booklet is to be used exclusively for Eastern Jungle Gym customers only. It is not to be handed out to the general public.
More informationBengal Fort Snack Bar Install Manual Version 7.16
Bengal Fort Snack Bar Install Manual Version 7.6 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact
More informationJaguar Playcenter Treehouse Panel Install Version 3.17
Jaguar Playcenter Treehouse Panel Install Version 3.17 Tools Needed for Assembly Tape Measure 2 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric
More informationUniversal Monkey Bar Install Manual
Universal Monkey Bar Install Manual Version 9.4 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact
More informationSTOP! Call Us First! DO NOT RETURN TO STORE.
2293-SB - NOTICE - This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN
More informationSafety Guide & Building Instructions
Safety uide & uilding Instructions PS 7958 (2) PS 7690 PS 7538 (2) PS 7688 PS 7668 (2) PS 8870 PS 8860 PS 8850 PS 8820 PS 8814 Featured Components (purchase separately): PS 7838 PS 7668 PS 7690 (2) PS
More informationSTOP! Call Us First! DO NOT RETURN TO STORE.
2981 - NOTICE - This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO
More informationBackyard Play Systems. Playset. Recommended for Ages 3 to 11 - BEFORE YOU BEGIN - - NOTICE -
2690-MB 1/25/2013 Customer Service 1-866-890-2211 1000 Ternes Drive Monroe, MI 48162 Backyard Play Systems Playset Model 4097 Model 6314 Tools Required Socket Set Hammer 9/16" Combination Wrench 3/16"
More informationMEADOWVALE II PLAY SYSTEM F24035
MEADOWVALE II PLAY SYSTEM F24035 INSTALLATION AND OPERATING INSTRUCTIONS 14 5 (4.4 m) 24 10 / 7.9m 12 10 / 3.9m 18 8 (5.7 m) 10 6 / 3.2m 28 / 8.5m WARNING To reduce the risk of serious injury or death,
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationStand Alone Swingbeam Install Manual Version 6.16
Stand Alone Swingbeam Install Manual Version 6.16 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact
More informationINSTALLATION AND OPERATING INSTRUCTIONS WARNING
W I N D A L E P L AY S Y S T E M F 2 3 2 2 0 INSTALLATION AND OPERATING INSTRUCTIONS 10'10 " 3.105m 24'11" 7.348m 12'-11" 3.93m 26' 7.924 m WARNING To reduce the risk of serious injury or death, you must
More informationParrot Island Monkey Bar Fort & Playcenter Install
Parrot Island Monkey Bar Fort & Playcenter Install Version 6.4 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet
More informationGRANDview Deluxe PlAY SYSTeM F24730
GRANDview Deluxe PlAY SYSTeM F24730 INSTALLATION AND OPERATING INSTRUCTIONS 28'-1" 16'-1" 7'-4" 26'-6" WARNING To reduce the risk of serious injury or death, you must read and follow these instructions.
More informationModel #SH & CH SH Pine CH Naturaline
Model #SH304-101 & CH304-101 Assembly Manual SH304-101 Pine CH304-101 Naturaline Component Parts A 2 ea. Angled Rail - 2 x 4 x 107-1/8" B 1 ea. Center Angled Rail - 2 x 4 x 107-1/8" C 9 ea. Rock Board
More informationMADISON PLAY SYSTEM F24040
MADISON PLAY SYSTEM F24040 INSTALLATION AND OPERATING INSTRUCTIONS 26 7'4" 27'4" 15'4" WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More informationTreehouse. Contains Assembly, Use, and Maintenance Instructions Rev
Treehouse Contains Assembly, Use, and Maintenance Instructions 5-70-0184 Rev 1-05.04.09 NOTICE: This residential play structure is intended for use by children ages 3-11. WARNING: This owner's manual contains
More informationClassic Tire Swing Set
Owners & Instruction Manual Classic Tire Swing Set This instruction booklet is to be used exclusively for Eastern Jungle Gym customers only. It is not to be handed out to the general public. Any duplication
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationINSTALLATION AND OPERATING INSTRUCTIONS
L A U R E N T I A N P L AY S Y S T E M F 2 3 2 8 0 INSTALLATION AND OPERATING INSTRUCTIONS 25'-3" 13'-3" 12'-9" 25'-10" WARNING To reduce the risk of serious injury or death, you must read and follow these
More informationANDORRA PLAY SYSTEM F24140C
ANDORRA PLAY SYSTEM F24140C INSTALLATION AND OPERATING INSTRUCTIONS 28 8.5m 14 5 (4.4 m) 9 2.7m 22 3 / 6.8m 10 3 / 3.1m 18 8 (5.7 m) WARNING To reduce the risk of serious injury or death, you must read
More informationFITNESS PLAYGROUND ITEM NO: 8202
FITNESS PLAYGROUND ITEM NO: 8202 OWNER S MANUAL CAUTION: This unit is designed to be used safely by up to 6 children between the ages of 3 years to 8 years old with a maximum weight of 80 pounds (36.3kgs)
More informationOasis PG05W Assembly Instructions
Oasis PG05W Assembly Instructions 817 Maxwell Avenue Evansville, IN 47711 1-800-GO-SWING www.escaladesports.com 2010 Escalade Sports 2L-7204-01 H A R D W A R E I D E N T I F I C A T I O N MB 6 (1 /2 X
More informationINSTALLATION AND OPERATING INSTRUCTIONS
A I N S L E Y P L AY S Y S T E M F 2 4 1 4 5 INSTALLATION AND OPERATING INSTRUCTIONS WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer to
More informationSANDY COVE PLAY SYSTEM F23242
SANDY COVE PLAY SYSTEM F23242 INSTALLATION AND OPERATING INSTRUCTIONS 26'6 25' 13 12'8" WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer
More informationSTOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll free number:
2321 - NOTICE - This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO
More information6.4 Deluxe Spiral Slide Install Manual
6.4 Deluxe Spiral Slide Install Manual Version 4.4 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric
More informationA I N S L E Y P L AY S Y S T E M F
A I N S L E Y P L AY S Y S T E M F 2 4 1 4 5 INSTALLATION AND OPERATING INSTRUCTIONS WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer to
More informationSTOP! Call Us First! DO NOT RETURN TO STORE.
2996 - NOTICE - This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO
More informationFit N Fun. Creative Cedar Designs
SKY VIEW GYM Fit N Fun Creative Cedar Designs 8 STOP PLEASE READ!! IF YOU HAVE ANY QUESTION OR ARE MISSING A PART, PLEASE DO NOT CONTACT THE RETAILER THAT YOU PURCHASED THIS PRODUCT FROM. PLEASE VISIT
More informationH HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT
Page 1 IMPORTANT PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationF 8:00 AM 6:00 PM EST 8:30 AM 4:30 PM EST
2490-D - NOTICE - This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO
More informationBROOKRIDGE PLAY SYSTEM F23235
BROOKRIDGE PLAY SYSTEM F23235 INSTALLATION AND OPERATING INSTRUCTIONS 12'-11" 24'-11" 12'-9" 26'-0" WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep
More informationINSTALLATION AND OPERATING INSTRUCTIONS WARNING. 375 Sligo Rd. West, PO Box 10 Mount Forest, ON Canada N0G 2L0
A P P L E T O N P L AY S Y S T E M F 2 4 1 4 8 INSTALLATION AND OPERATING INSTRUCTIONS WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer
More informationHAZELWOOD PLAY SYSTEM F24152
HAZELWOOD PLAY SYSTEM F24152 INSTALLATION AND OPERATING INSTRUCTIONS 24' 12' 12'-8" 27'-0" WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer
More informationHigh End Residential In-Ground Basketball System Owners Manual
High End Residential In-Ground Basketball System Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. Write Model Number From Box Here: READ AND UNDERSTAND OPERATOR'S
More informationINSTALLATION AND OPERATING INSTRUCTIONS WARNING. 375 Sligo Rd. West, PO Box 10 Mount Forest, ON Canada N0G 2L0
S U N B I S T R O P L AY S Y S T E M F 2 4 1 5 0 INSTALLATION AND OPERATING INSTRUCTIONS 22'-10" 10'-10" 27'-0" 9'-0" WARNING To reduce the risk of serious injury or death, you must read and follow these
More informationHAZELWOOD PLAY SYSTEM F24152
HAZELWOOD PLAY SYSTEM F24152 INSTALLATION AND OPERATING INSTRUCTIONS 24' 12' 12'-8" 27'-0" WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer
More informationMEADOWVALE II PLAY SYSTEM - F24035EX
MEADOWVALE II PLAY SYSTEM - F24035EX INSTALLATION AND OPERATING INSTRUCTIONS 24 10 / 7.9m 12 10 / 3.9m 10 6 / 3.2m 28 / 8.5m WARNING To reduce the risk of serious injury or death, you must read and follow
More informationMONKEY TOWER PG123W. RECOMMENDED TOOLS: Impact Driver (2) Saw Horses (4) Bar Clamps or C-Clamps
MONKEY TOWER PG3W REQUIRED TOOLS: () 3/4" Sockets and Ratchets 3/4" Wrench /" Socket and Wrench 9/6" Socket and Wrench 5/6" Allen Wrench Drill with Phillips Driver Bit 3/8" Drill Bit /8" Drill Bit Hammer
More informationBackyard Play Systems ULTRA PLAYSET. Recommended for Ages 3 to 11 - BEFORE YOU BEGIN - - NOTICE -
2293-ST 01/10/2013 Customer Service 1-866-890-2211 1000 Ternes Monroe, MI 4816 Backyard Play Systems ULTRA PLAYSET Model 4098, 6315 Tools Required Sockets: 7/16" 9/16" Socket Extension Ratchet Hammer 5
More informationDASHLEY COLLECTION GAZEBO
DASHLEY COLLECTION GAZEBO MODEL NO. 088-1760-6 INSTRUCTIONS Toll-free: 1-888-670-6684 IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future
More informationParrot Island Fort Install Manual Version 3.16
Parrot Island Fort Install Manual Version 3.16 Tools Needed for Assembly Tape Measure 4 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationRIDGEVIEW DELUXE CLUBHOUSE PLAY SYSTEM F270855
INSTALLATION AND OPERATING INSTRUCTIONS 26' 5" RIDGEVIEW DELUXE CLUBHOUSE PLAY SYSTEM F270855 14' 5" 13 6" 26' 6" WARNING To reduce the risk of serious injury or death, you must read and follow these instructions.
More information- NOTICE STOP!
- NOTICE - This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. 2321 STOP! Call Us First! DO NOT RETURN TO
More informationFOR RESIDENTIAL USE ONLY
ASSEMBLY MANUAL By illustration #1 If you have problems or questions about your Creative Playthings Playset, DO NOT CALL THE RETAILER. Contact Creative Playthings Customer Service at 1-800-833-4001 or
More informationUser Guide. 10ft (3.05m) Jumpking Classic Premium. Got a Problem building your trampoline? Call us on and we can help
User Guide 10ft (3.05m) Jumpking Classic Premium Got a Problem building your trampoline? Call us on 0344 800 4060 and we can help Patent no: DE602006006495D1, EP1721640B1 and US7628731 WARNING: Read these
More informationTITAN INDUSTRIAL RACK 6-FOOT TALL / 4-SHELF
TITAN INDUSTRIAL RACK 6-FOOT TALL / 4-SHELF DXST10000 IMPORTANT: Please read this manual carefully before assembling this storage rack and save it for reference INSTRUCTION MANUAL 3 TABLE OF CONTENTS
More information176 S. New Holland Road Gordonville, PA Tel: Fax: Summit Tower
176 S. New Holland Road Gordonville, PA 17529 Tel: 717-768-0066 Fax: 717-768-8569 A S S E M B LY M A N U A L Summit Tower Summit Tower Assembly Manual revised 9/07/05 Dear Customer, Thank you for your
More informationReal Life Ninja Complete Starter Pack (14ft. Warped Wall) Assembly Instructions
MATERIALS: 3 - Main Sections (Only 2 Sections for 10 ) 8 3 deck screws for joining sections inside of 2 Rock Wall Panels (with pre-installed t-nuts. Top panel comes with ladder mounting block preinstalled.)
More informationCostco High Wire Assembly Instruc ons & Owner's Manual
2254 Costco High Wire Assembly Instruc ons & Owner's Manual Important! Read this manual completely through before assembly and use. Consumer assistance Toll free If you need to order replacement parts
More informationSafety Guide & Assembly Instructions
Safety Guide & ssembly Instructions Featured Components (purchase separately): Featured Components (purchase separately): PS 8876 PS 7980 PS 7676 PS 7946 PS 7958 PS 8821 PS 8821 Featured Components (purchase
More informationF 8:00 AM 7:00 PM EST 8:30 AM 4:30 PM EST
2320 - NOTICE - This playset product is not intended for public use. It is intended for residential application and is not warranted for public or commercial use. STOP! Call Us First! DO NOT RETURN TO
More informationOrangutan Fort Installation Manual Version 10.15
Orangutan Fort Installation Manual Version 0.5 Tools Needed for Assembly Tape Measure 4 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact
More informationToucan Playcenter Install Manual Version 1.17
Toucan Playcenter Install Manual Version.7 Tools Needed for Assembly Tape Measure 4 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact Gun
More informationsouthpaw enterprises, inc.
Store these instructions in a safe place or with the enclosed maintenance checklist In-FUN-ity Climbing System Assembly Examples This example sheet is intended to supplement the instruction sheets that
More information5.5 Mega Texan Install Manual Version 6.16
5.5 Mega Texan Install Manual Version 6.6 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact Gun
More informationINSTALLATION AND OPERATING INSTRUCTIONS
F O R E S T H I L L R E S O RT P L AY S Y S T E M F 2 3 1 8 0 INSTALLATION AND OPERATING INSTRUCTIONS 7'-7" 28'-4" 16'-4" 26'-0" WARNING To reduce the risk of serious injury or death, you must read and
More informationTITAN INDUSTRIAL RACK 4-FOOT TALL / 3-SHELF
TITAN INDUSTRIAL RACK 4-FOOT TALL / 3-SHELF DXST4500 IMPORTANT: Please read this manual carefully before assembling this storage rack and save it for reference INSTRUCTION MANUAL 3 TABLE OF CONTENTS TECHNICAL
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.0-7 Table of Contents PAGE Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationPortable System Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI U.S.A.
Portable System Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. Adult Assembly Required. This manual, accompanied by sales receipt, should be saved and kept
More informationASSEMBLY INSTRUCTIONS
SPIRAL WAVE SLIDE ASSEMBLY FOR 4 FOOT DECKS F24570 ASSEMBLY INSTRUCTIONS 18 8 (5.7 m) 14 5 (4.4 m) Solowave Design 375 Sligo Rd. West, PO Box 10 Mount Forest, ON Canada N0G 2L1 General Inquiries: 8:00am
More informationBAYBERRY PLAY HOUSE P280050
BAYBERRY PLAY HOUSE P280050 INSTALLATION AND OPERATING INSTRUCTIONS 14 5 (4.4 m) 7 8 18 8 (5.7 m) 4 2 WARNING To reduce the risk of serious injury or death, you must read and follow these instructions.
More informationImportant safety considerations
Important safety considerations This product is intended for use by children not less than 2 years of age. Warning: possible problems of entrapment could occur if used by children under 2 years of age.
More informationBALMORAL A24655E for use with SELWOOD 1.2 METRE FORT A23835E INSTALLATION AND OPERATING INSTRUCTIONS WARNING. For Outdoor Family Domestic Use Only
7.15m 3.15m BALMORAL A24655E for use with SELWOOD 1.2 METRE FORT A23835E INSTALLATION AND OPERATING INSTRUCTIONS 5.22m 1.22m WARNING To reduce the risk of serious injury or death, you must read and follow
More informationImportant Loading Information. Tools Required. Meridian Lateral Files Instructions
Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information
More informationReal Life Ninja Starter Pack 1 Assembly Instructions
Real Life Ninja Starter Pack 1 Assembly Instructions MATERIALS: Warped Wall 3 - Main Sections (Only 2 Sections for 10 Warped Wall) 8 3 deck screws for joining sections inside of Warped Wall 2 Rock Wall
More information1531 Fort Add On **!!IMPORTANT-PLEASE READ!!**
1531 Fort Add On **!!IMPORTANT-PLEASE READ!!** This Add-On kit will require you to deviate from the main instruction manual. Please follow the outline below so that you will know what steps to be aware
More informationClearSpan PolyMax Windbreak Wall
ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: February 2007ldg STK# DIMENSIONS
More informationPortable System Owners Manual
Portable System Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. Adult Assembly Required. This manual, accompanied by sales receipt, should be saved and kept
More information(This page intentionally left blank.)
2358 (This page intentionally left blank.) Customer Service 1-866-890-2211 1000 Ternes Monroe, MI 4816 Backyard Play Systems Playset 2358 05/27/2011 Model 4500, 4505, 5005, 5008, 6096, 6098. Tools Required
More information6' Wide Premium Greenhouse Benches
6' Wide Premium Greenhouse Benches Premium Greenhouse Bench with Stationary Top 2015 FarmTek All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 112416S6X08 6' W x 3' H
More information