6.4 Texan Playcenter Install Manual

Transcription

1 6.4 Texan Playcenter Install Manual Version 3.4 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact Gun Claw Hammeror Rubber Mallet Pliers or Vise Grips 7/6 Deep Well Socket 9/6 Deep Well Socket 3/4 Deep Well Socket /8, /4, and 9/6 Drill Bits Phillips Head Screw Bits An Adult with two Adult Helpers Please familiarize yourself with the install manual, parts/components and general construction process of your new swing set before getting started. Approximate assembly time: 6 to 8 hours. 6 foot unobstructed safety perimeter around swing set recommended. Houston, TX kid STRUCTURES INC.

2 When choosing a location for your swing set, always keep your child or children s safety in mind. Here are some recommendations to help you locate and install a safe play area. This play set is designed for the use of 4 occupants who have a combined weight not exceeding 800 pounds on the elevated floor; 3 occupants who have a combined weight of 525 pounds on the swing area; for a total Unit capacity of 5 occupants who have a combined weight of 325. (this weight is not including the picnic table area) On-site adult supervision is required. The swing set should be located on level ground. The stationary components such as ladders and slides are required to be a minimum of six feet from any structure or obstruction such as a fence, garage, house, tree, overhanging branches, electrical wires, clotheslines, etc. Any swinging equipment is also required to be a minimum distance twice the height of the swing beam away from these obstructions or structures as well. The swing set should be located a safe distance from any water hazards, such as a lake, river, bayou, swimming pool, etc. Do not install this residential swing set in a commercial setting. This swing set is not manufactured for commercial usage and will void all warranties. Tree Frogs Wooden Swing Set Factory is not responsible for any damages or injuries resulting from this swing set being used in a commercial setting. Never install this swing set indoors; or over concrete, asphalt, packed earth, grass, carpet or any other hard surface. A fall onto a hard surface can result in serious or fatal injury. The U.S. Consumer Product Safety Commission (CPSC) recommends that you install and maintain a resilient surface under your swing set. The CPSC s Consumer Information Sheet for Playground Surfacing Materials is on the next page. A resilient surface, should be installed after the swing set has been completely assembled according to these instructions. The swing set must rest on solid ground. Please note that this swing set has a maximum fall height of 7. Here are some maintenance tips required to insure safe play on your swing set for years of fun. At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed, swing seats, chains, ladders, slides, rope and wood components for sign of deterioration and replace if necessary. On a yearly basis, we recommend that you coat your swing set with a sealant or preservative. You may also want to spot sand any areas prior to sealing. ** Special note: Although we recommend that you reseal your swing set annually, you may have to touch up the high traffic areas and/or areas that have a high exposure to direct sunlight.** Be sure that the sealant you select is non-toxic and child safe. Your local Tree Frogs Wooden Swing Set Factory dealer may offer a complete power wash and reseal and maintenance program. Do not use line trimmers or weed eaters around your swing set. The line will remove both paint and wood from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited warranty. Remove plastic swing seats and take in doors or do not use when temperature drops below 0 F. Weight Limits for Tree Frogs Swing Sets Fort Platform: 800 Lbs. Total Weight Swing Belts: 75 Lbs. Trapeze: 25 Lbs. Full Bucket Swing: 50 Lbs. toddler Bucket Swing: 50 Lbs. Tire Swing: 25 Lbs. Total Weight Rope Ladder: 75 Lbs. rock Wall: 50 Lbs. All Slides: 25 Lbs. Tree Frogs recommends that the weight limits for all components must not be exceeded. Failure to adhere to these and other safety guidelines could result in damage to the swing set and/or injury to the users. Please keep this install manual for future reference.

3 To insure SAFE PLAY adults must teach children: Not to walk close to, in front of, behind, or between moving items. Not to swing empty swing seats. Not to swing sideways into the path of adjacent swings. Not to use the swing set in a manner other than that for which it is intended. Not to get off the equipment while it is in motion. Not to jump off the tower. Not to stand in the swing seats. Not to swing so high that chains become slack, or above the height of the swing support. Not to jump on a slide. Not to climb on top of the swing support. Not to attach to the swing set any item that is not specifically designed for use with the equipment, such as (but not limited to) jump ropes, clotheslines, pet leashes, cables, and chains. These may become strangulation hazards. To hold on to swings and climbers with both hands. To slide feet first, never head first. To watch for other children while swinging or playing near the swing set. To also insure SAFE PLAY adults must: Limit climbing and swinging heights to each child s ability. Verify that suspended climbing ropes are secured at both ends. Verify that suspended climbing ropes cannot be looped back on themselves. Dress children appropriately for play. Use well-fitted shoes that do not have slippery soles. Avoid ponchos, scarves, hoods, loose fitting clothing, neckties, and any clothing with a drawstring. Serious injury could result should any part of the children s clothing become entangled in the swing set. Do not allow children to play wearing helmets. Remember that children are inventive. When they develop games that are unsafe, be alert and change the rules. IMPORTANT - PLEASE READ As fresh lumber acclimates to its new environment, the natural tendencies of the tree can show itself in the form of checks, or cracks in the lumber. In almost all cases this is normal and it will not affect the structural integrity of your play set. Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, checking or any other physical properties of wood that do not present a safety hazard, are not covered by this warranty. Defects that develop because the product is exposed to extreme climate conditions are not covered by this warranty. Defects that develop as a result of faulty or improper installation of the product are also not covered by this warranty. Most cracks are not warrantable, however if you believe that the integrity of your play set is compromised by this natural occurrence, please contact the Tree Frogs Swing Set Dealer that you purchased your swing set from. We appreciate your purchase and know that you will enjoy your play system for many years to come.

4 Depending on your experience, assembly of our play sets can take as little as 6 hours up to 24 hours, depending on size, after inventory of parts; therefore, we recommend you set aside a full two days for assembly. Identify all of the parts for your play set. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. After everything is laid out, check carefully to ensure all parts are present. Make sure there are no broken boards. Find an area to sort your hardware. It is best to open the hardware on a solid surface so that you do not lose any pieces in the grass. This will save time and familiarize you with all the different pieces in the hardware bag. **Important note: Wood has some natural defects such as knots, surface cracks, etc... We reject parts that are structurally defective. We use a high quality lumber in our structures; however, you should inspect each part for splinters or rough spots and sand them smooth to prevent injury.** After familiarizing yourself with all of the components, read all instructions thoroughly. Reading instructions after you have studied the parts will help you understand more clearly the installation process, and help to eliminate unnecessary mistakes. Pay close attention to the diameter and length of each bolt and screw. Never tighten hardware completely at first. It helps to have some adjustment for bolt alignment while you are attaching parts together. After everything is square, tighten each joint. After the main unit is assembled it is critical that the floor is level and square. If the main frame is not level, the walls and floor will be out of square. After you complete installation, make sure every bolt, screw, and nut is tight, and every board is secure. Wood will expand and contract with the seasons. Place the set on level ground, not less than 6ft from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. All /4 and 3/8 lag bolts must have pre-drilled holes -/2 to 2 deep. Use a /8 drill bit for the /4 lag bolts and /4 drill bit for 3/8 lag bolts. Use pre-drilled holes in facias as a reference for placing lag bolt pilot holes. If a board lifts or rises causing a gap between boards when running in lag bolts or screws, back out the screw or lag bolt and press or apply pressure (but not enough to crack or break board) while re running in the lag bolt or screw in the same hole. Do not over tighten bolts, lag bolts or screws. You can damage boards, break hardware, and/or strip out the hardware. When using hammer do not beat on the hardware, but gently tap it in. Never beat on the wood as it will leave marks. Complete the steps which will be the basic frame of the fort {i.e. four corner posts with base (sand box boards) and deck supports} Position in the most level area chosen for the play set, keeping in mind the location and size of the swing beam, ladder, slides, etc. that extend off the fort. Once the frame is in the final position, check for vertical and horizontal levelness to determine which side(s) will need to be dug into the ground to level the play set. With a shovel, score the ground around the outside edges of the sandbox boards on the high side of the fort. This is the area that will be dug in. Make sure to score deep enough; the scored lines will be your digging template. Push the frame off and away from the scored area, far enough to dig and remove dirt to reach the appropriate depth. Dig a channel along the scored line(s) for the base of the fort (corner post and sandbox boards) to rest into. Dig the channel(s) to the same level depth. The bottom of the channel(s) should be level to each other so your frame doesn t teeter or rock because the channel(s) are uneven. Once you have removed enough grass and dirt, slide/push the frame into the channel(s). Place a level on the vertical and horizontal boards of the frame to determine if enough soil, or too much, was removed. Repeat this process until the basic frame is plumb and level and in its final position before completing the rest of the assembly. Measure to make sure fort is square. ** Important: if you require a channel depth of more than 6, then we recommend you have your play set area professionally graded before completing assembly. **

5 CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS The U.S. Consumer Product Safety Commission (CPSC) estimates that about 00,000 playground equipment related injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall onto a shockabsorbing surface is less likely to cause a serious injury than a fall onto a hard surface. However, it should be recognized that some injuries from falls will occur no matter what playground surfacing material is used. Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Grass may appear to be acceptable, but can turn to hard packed earth in areas of high traffic. Shredded bark mulch, wood chips, or fine gravel are considered to be acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around play equipment. TABLE -CRITICAL HEIGHTS (in feet) OF TESTED MATERIAL MATERIAL UNCOMPRESSED DEPTH COMPRESSED DEPTH 6 Inch 9 Inch 2 Inch 9 inch Wood Chips Double Shredded Bark Mulch Engineered Wood Fibers 6 7 >2 6 Fine Sand Coarse Sand Fine Gravel Medium Gravel Shredded Tires** 0-2 N/A N/A N/A ** This is data from tests conducted by independent testing laboratories on a 6 inch depth of uncompressed shredded tire samples produced by four manufacturers. The test reported critical heights, which varied from 0 feet to greater than 2 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F292. Table should be read as follows: If, for example, uncompressed wood chips are used at a minimum of 6 inches, the Critical Height is 7 feet. If 9 inches of uncompressed wood chips are used, the Critical Height is 0 feet. It should be noted that, for some materials, the Critical Height decreases when the material is compressed. It is recommended that a shock absorbing material should extend a minimum of 6 feet in all directions from the perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure. This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability in your area, and its cost. This information has been extracted from the CPSC publications Playground Surfacing-Technical Information Guide and Handbook for Public Playground Safety. Copies of these reports can be obtained by sending a postcard to: Office of Public Affairs U.S. Consumer Product Safety Commission Washington, D.C Toll-free Hotline: or at

6 Item No. UB- ub-2 ub-3 ub-4 ub-5 ub-6 ub-7 ub-8 ub-9 ub-0 ub- ub-2 Playcenter Universal Bundle &2 Part Number Part Description Universal Playcenter Mainbeam Uni. Playcenter Center Post (l) Gusset Bracket (R) Gusset bracket (l) Playcenter Support Gusset (R) Playcenter support gusset universal Rope block universal rail Bottom universal entrapment block uni. playcenter corner post uni. pc. top joist w/ swing holes uni. pc. top joist QTY Texan Playcenter Bundle tx- tx-2 tx-3 tx-4 tx-5 tx Texan Playcenter upper rope arm texan playcenter tarp board Universal Tarp Board texan playcenteer ground runner texan playcenter lower rope runner texan playcenter upper accessory arm Texan Playcenter Bundle b. 6tx- 6tx-2 6tx-3 6tx-4 6tx-5 6tx-6 6tx-7 6tx-8 6tx-9 6tx (l) playcenter wood step ladder leg center wood step/ chain ladder leg (r) playcenter chain ladder leg 7 /4 wood step (R) PC rockwall ladder leg (l) pc rockwall ladder leg tx pc rockwall board w/ out holes tx pc rockwall board w/ holes tx pc rockwall board w/ rope hole rope run-cedar

7 Texan playcenter wood roof bundle Item No. Part Number Part Description wr- wr-2 wr-3 wr-4 wr-5 wr-6 wr-7 wr-8 wr-9 wr-0 wr- wr-2 wr-3 wr-4 wr-5 wr TX PC Wood roof tarp board Uni. pc (l) wood roof support uni. pc (r) wood roof support TX PC wood roof board tx pc wood roof board ripped qc pc wood roof runner qc pc wood roof runner #2 qc pc wood roof center support qc pc wood roof center support #2 universal center fan board universal pc bottom fan board universal pc center fan board uni. pc. Long (l) side fan board uni. pc. Long (r) side fan board uni. pc. short (r) side fan board uni. pc. short (l) side fan board QTY Universal Rail(Count is for a single rail) ra- ra-2 ra Universal rail top universal rail bottom universal spindle 5 Universal Deck Deck- DECK-2 DECK-3 DECK Deck Runner Deck Support Small Deck Board Large Deck Board Texan PC Box a. or b.(color depends on box) 6pc- 6pc-2 6pc-3 6pc-4 6pc-5 6pc-6 6pc-7 6pc-8 6pc-9 6pc-0 6PC large rock (multi- color) large rock (green) 6 yellow rope 8 yellow rope 9 ships wheel (green) 9 ships wheel (yellow) 66 plastisol coated chain (yellow) 66 plastisol coated chain (green) tire swivel 20 trapeze bar w/ rings (yellow) /4 x 25 Playgrip Tube PC Coated

8 Item No. tb- tb-2 tb-3 tarp bags (color depends on box) Part Number Part Description tx pc tarp bag (byb) tx pc tarp bag (ryr) tx pc tarp bag (green) tire tire tire swing tire QTY. tst- tst-2 tst-3 tst-4 tst-5 tst-6 tst-7 tst-8 tst-9 tst-0 TX Playcenter Standard Box x 63 Chain Ladder- (Yellow) /4 x 44 Playgrip Tube PC Coated /4 x 25 playgrip tube pc coated /4 playgrip safety handles /4 playgrip ladder handles ductile iron swing hangers spring clips 0mm x 00mm tree frogs plaque telescope tire swing eye bolt st- st-2 st-3 st-4 st-5 st-6 st-7 st-8 st-9 st-0 st- st-2 st-3 st-4 st-5 st-6 st-7 st-8 ST-9 ST-20 tx playcenter- standard box hardware /4 uss flatwasher /2 uss flatwasher 3/8 uss flatwasher /4 uss flatwasher /2 split lockwasher 3/8 split lockwasher /2 hex nut 3/8 nylon insert locknut /2 x 7 carriage bolt /2 x 4 /2 carriage bolt 3/8 x 5 hex bolt 3/8 x 5 lag bolt 3/8 x 3 /2 lag bolt /4 x 4 /2 lag bolt /4 x 3 lag bolt #4 x /4 pan phillips TS #4 x 2 Pan phillips ts 3/8 bolt cup 3/8 Acorn Nut /2 Acorn nut

9 6pc-2 6pc-3 6pc-4 6pc-5 6pc-6 6pc tx playcenter- hardware bag /2 coated deck screws /4 x 4 /2 lag bolt /4 x /2 pan phillips m/s /4 x 7/6 4 prong t-nut /4 uss flatwasher 2 metal tap screw Texan playcenter wood roof HARDWARE Item No. Part Number Part Description QTY. wr-7 wr-8 wr-9 wr-20 wr-2 wr-22 wr-23 wr-24 wr-25 wr-25 wr /2 USS FLATWASHER 3/8 USS FLATWASHER /4 USS FLATWASHER 3/8 SPLIT LOCKWASHER 3/8 HEX NUT 3/8 ACORN NUT 3/8 X 5 CARRIAGE BOLT /4 X 4 /2 LAG SCREW /4 X 3 LAG SCREW /4 X 2 LAG SCREW 5/8 COATED DECK SCREWS DECK hardware DECK /2 COATED DECK SCREWS 84 universal rail hardware(count FOR ONE RAIL) RA /2 COATED DECK SCREWS 20

10 #UB Universal PC Main Beam 07 QTY. 2 Playcenter Universal Bundle & 2 #UB Uni. PC Center Post 88 QTY. 2 #UB (L) Gusset Bracket 9 QTY. 5 #UB (R) Gusset Bracket 9 QTY. 5 #UB (L) PC Support Gusset 6 QTY. 2 #UB (R) PC Support Gusset 6 QTY. 2 #UB Universal Rope Block QTY. #UB Universal Rail Bottom 25 QTY. 3 #UB Universal Ent. Block 25 QTY. #UB Uni. PC. Corner Post 39 QTY. 4 #UB Uni. PC. Top Joist w Swing Holes 25 QTY. #UB Uni. PC. Top Joist 25 QTY.

11 #TX TX PC Upper Rope Arm 05 /2 QTY. Playcenter Universal Bundle & 2 #TX TX PC Tarp Board 68 QTY. 2 #TX Universal Tarp Board 6 QTY. #TX TX PC Ground Runner 7 QTY. #TX TX PC Lower Rope Runner 07 QTY. #TX TX PC Upper Acc. Arm 05 /2 QTY. #5TX (L) PC Wood Step Ladder Leg 88 /2 QTY. 6.4 Texan PC Bundle a. #5TX Center Wood Step/ Chain Ladder Leg 88 /2 QTY. #5TX (R) PC Chain Ladder Leg 88 /2 QTY.

12 #5TX Wood Step 8 /2 QTY Texan PC Bundle a. Cont. #5TX (R) PC Rockwall Ladder Leg 88 /2 QTY. #5TX (L) PC Rockwall Ladder Leg 88 /2 QTY. #5TX TX PC RW Board W/ Out Holes 43 /2 QTY. 4 #5TX TX PC RW Board W/ Holes 43 /2 QTY. 8 #5TX TX PC RW Board W/ Rope Hole 43 /2 QTY. #WR TX PC Wood Roof Tarp Board QTY. Texan PC WOOD ROOF Bundle #WR Uni. PC (L) Wood Roof Support 79 QTY. 2 #WR Uni. PC (R) Wood Roof Support 79 QTY. 2

13 #WR TX PC Wood Roof Board 68 QTY. 32 Playcenter Universal Bundle & 2 #WR TX PC WR Board Ripped 68 QTY. 2 #WR QC PC Wood Roof Runner 36 QTY. 4 #WR QC PC Wood Roof Runner 39 /2 QTY. 4 #WR QC PC Wood Roof Center Support 36 QTY. 2 #WR QC PC Wood Roof Center Support 39 /2 QTY. 2 #WR Universal Center Fan Board 5 /4 QTY. 2 #WR Uni. PC Bottom Fan Board 62 QTY. 2 #WR Uni. PC Center Fan Board 20 /4 QTY. 2 #WR Uni. PC Long (L) Side Fan Board 9 QTY. 2 #WR Uni. PC Long (R) Side Fan Board 9 QTY. 2 #WR Uni. PC Short (R) Side Fan Board 4 QTY. 2 #WR Uni. PC Short (L) Side Fan Board 4 QTY. 2

14 RA Universal Rail Top QTY. 3 RAIL Bundle RA Universal Rail Bottom QTY. 3 RA Universal Rail Picket QTY. 5 DECK Deck Runner QTY. 4 DECK Bundle DECK Deck Support QTY. 2 DECK Small Deck Board QTY. 8 DECK Large Deck Board QTY. 6

15 Texan Box A. & B. #6PC Large Rock (Multi Color) QTY. 8 #6PC Large Rock (Green) QTY. 8 #6PC Yellow Rope QTY. #6PC Yellow Rope QTY. 3 #6PC Ship s Wheel- Green QTY. #6PC Ship s Wheel- Yellow QTY. #6PC Plastisol Coated Chain (Yellow) QTY. 3 #6PC Plastisol Coated Chain (Green) QTY. 3 #6PC Tire Swivel QTY. #6PC Trapeze w/ 43 Chain- Yellow QTY. #6PC /4 x 25 Tube PC Coated QTY.

16 #TB TX PC Tarp Bag- BYB QTY. Tarp (Color Varies With Order) #TB TX PC Tarp Bag-RYR QTY. #TB TX PC Tarp Bag- Green QTY. #TST x 63 Chain Ladder- (Yellow) QTY. #TST /4 x 44 Tube PC Coated QTY. Texan PC Standard Box #TST /4 x 25 Tube PC Coated QTY. #TST /4 Playgrip Safety Handles QTY. 4 #TST /4 Playgrip Ladder Handles QTY. 2 #TST Ductile Iron hangers QTY. 2 #TST Spring Clips 0 x 00mm QTY. 2 #TST Tree Frogs Plaque QTY. #TST Telescope QTY. #TST Tire Swing Eye Bolt QTY.

17 Texan Standard Hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) #ST /4 USS FLatwasher QTY. 22 #ST /2 USS FLatwasher QTY. 22 #ST /8 USS FLatwasher QTY. 5 #ST /4 USS FLatwasher QTY. 47 #ST /2 Split Lockwasher QTY. 22 #ST /2 x 7 Carriage Bolt QTY. 20 #ST /8 Acorn Nut QTY. 4 #ST /8 Split Lockwasher QTY. 4 #ST /2 Hex Nut QTY. 22 #ST /8 Nylon Locknut QTY. 4 #ST /2 Acorn Nut QTY. 22 Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

18 Texan Standard Hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) #ST /2 x 4 /2 Carriage Bolt QTY. 2 #ST /4 x 3 Lag Bolt QTY. 2 #ST /8 x 5 Hex Bolt QTY. 4 #ST /8 x 5 Lag Bolt QTY. #ST /8 x 3 /2 Lag Bolt QTY. 36 #ST /4 x 4 /2 Lag Bolt QTY. 20 Measurement taken from bottom of bolt head to the bottom of bolt

19 Texan Standard Hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) #ST #4 x /4 Pan Phillips TS QTY. 2 #ST #4 x 2 Pan Phillips QTY. 5 #ST /8 Bolt Cup QTY. 4 #6PC /2 Coated Deck Screw QTY TX PC Hardware Bag #6PC /4 x 4 /2 Lag Bolt QTY. 28 #6PC /4 x7/6 4 Prong T-Nut QTY. 36 #6PC /4 USS Flatwasher QTY. 64 #6PC /4 x /2 Pan Phillips QTY. 36 #6PC Metal tap Screw QTY. 6 Measurement taken from bottom of bolt head to the bottom of bolt

20 TEXAN WOOD ROOF Hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) #WR /2 USS Flatwasher QTY. 4 #WR /8 USS Flatwasher QTY. 4 #WR /4 USS Flatwasher QTY. 38 #WR /8 Split Lockwasher QTY. 4 #WR /8 Hex Nut QTY. 4 #WR /8 Acorn Nut QTY. 4 #WR /8 x 5 Carriage Bolt QTY. 4 #WR /4 x 4 /2 Lag Bolt QTY. 24 #WR /4 x 3 Lag Bolt QTY. 2 #WR /8 Coated Deck Screw QTY. 20 Rail Hardware #RA /2 Coated Deck Screw QTY. 20 #WR /4 x 2 Lag Bolt QTY. 4 Measurement taken from bottom of bolt head to the bottom of bolt

21 PARTS #6TX- - (L) Playcenter Wood Step Ladder Leg- () #6TX- 2- Center Wood Step/ Chain Ladder Leg- () #6TX- 3- (R) Playcenter Chain Ladder Leg- () #6TX- 4-5 /4 Wood Step- (6) Ladder/ Chain Ladder Assembly Hardware #6PC- 3- /4 x 4 /2 Lag Bolt- (24) #6PC- 6- /4 USS Flatwasher- (24) #6PC- 7-2 Metal Tap Screw- (6) #6PC-- /4 x 25 Tube- () #TST- 2 - /4 x 44 Playgrip Tube PC Coated- () #TST- 3 - /4 x 25 Playgrip Tube PC Coated- () #TST- - 2 x 63 Chain Ladder- () TST-2 6TX-3 6TX-2 6TX- 6TX-4 TST- TST-3 6PC- 6PC-6 6PC-7 6PC-3

22 PARTS #TX-4 - Texan Playcenter Ground Runner- () #UB-3 - (L) Gusset Bracket- () #UB-4 - (R) Gusset Bracket- () Ladder/ Chain Ladder Assembly Hardware #ST- 2-3/8 x 5 Lag Bolt- (3) #ST- 3-3/8 USS Flatwasher- (7) #ST- 3-3/8 x 3 /2 Lag Bolt- (4) TX-4 UB-3 UB-4 ST-2 ST-3 ST-3 ST-3

23 PARTS #6TX-5- (R) Rockwall Ladder Leg () #6TX-6- (L) Rockwall Ladder Leg () #6TX-7- TX PC Rockwall Board W/ Out Holes- (6) #6TX-8- TX PC Rockwall Board W/ Holes- (9) #6TX-9- TX PC Rockwall Board W/ Rope Hole- () Rockwall Assembly Hardware #6PC-2-2 /2 Coated Deck Screws (56) #6PC-4- /4 x /2 Pan Phillips M/S- (32) #6PC-6- /4 USS Flatwasher- (32) #6PC-5- /4 x 7/6 4 Prong T-Nut (32) #6PC- or 2- Large Rock- (6) 6TX-7 6PC-5 6TX-9 6TX-8 6TX-8 6PC-4 /2 6PC-6 6PC- or 2 6PC-2 6TX-8

24 Rockwall Assembly PARTS #TX-5 - Texan Playcenter Lower Rope Runner- () #UB-3 - (L) Gusset Bracket- () #UB-4 - (R) Gusset Bracket- () Hardware #ST- 2-3/8 x 5 Lag Bolt- (2) #ST- 3-3/8 USS Flatwasher- (6) #ST- 3-3/8 x 3 /2 Lag Bolt- (4) TX-5 UB-4 2 Space UB-3 ST-2 ST-3 ST-3 ST-3

25 Rail Assembly PARTS #RA-- Universal Rail Top- () #RA-2- Universal Rail Bottom- () #RA-3- Universal Spindle- (5) #UB-- Universal PC Main Beam- (2) Main Assembly Hardware #RA-4-2 /2 Coated Deck Screw- (20) #ST-20- /2 Acorn Nut- (4) #ST-9- /2 x 7 Carriage Bolt- (4) #ST-- 3/4 USS Flatwasher- (4) #ST-2- /2 USS Flatwasher- (4) #ST-5- /2 Split Lockwasher-(4) #ST-7- /2 Hex Nut- (4) 2 3/6 Gap Between Spindles 3 /2 Gap UB- RA- RA-3 RA-2 ST-7 ST-20 ST- ST-9 ST-2 ST-5 RA-4

26 Main Assembly PARTS #UB-5- (L) Playcenter Support Gusset- (2) #UB-6- (R) Playcenter Support Gusset- (2) #UB-2- Uni. Playcenter Center Post- (2) #UB-0- Uni. Playcenter Corner Post- (4) Hardware #ST- 9- /2 x 7 Carriage Bolt- (6) #ST-- 3/4 USS Flatwasher- (6) #ST- 2- /2 USS Flatwasher- (6) #ST-5- /2 Split Lockwasher- (6) #ST- 7- /2 Hex Nut- (6) #ST-20- /2 Acorn Nut- (6) #ST- 3-3/8 x 3 /2 Lag Bolt- (6) #ST -3-3/8 USS Flatwasher- (6) UB-5 UB-6 ST-3 ST-3 ST-20 ST-5 ST-2 ST- ST-9 ST-7

27 Deck Assembly PARTS Deck-- Deck Runner- (4) Deck-2- Deck support- (2) Deck-3- Small Deck board- (8) DECK-4- Large Deck Board- (6) Hardware DEck-5-2 /2 Coated deck screw- (84) 3 /2 Gap 3 /2 Gap 2 /4 Gap 24 /4 Gap DECK- DECK-4 DECK-5 DECK-4 DECK-5 DECK- DECK-2 DECK-3

28 PARTS Deck- Universal Deck (2) Main Assembly Hardware #ST-4- /4 x 4 /2 Lag Bolt- (8) #ST- 4- /4 USS Flatwasher (8) DECK ST-4 ST-4

29 Main Assembly PARTS #UB-3- (L) Gusset Bracket- (2) #UB-4- (R) Gusset bracket- (2) #UB-- Uni. PC Top Joist W/ Swing Holes- () #UB-2- Uni. PC Top Joist- () Hardware #ST- 9- /2 x 7 Carriage Bolt- (6) #ST-- 3/4 USS Flatwasher- (6) #ST- 2- /2 USS Flatwasher- (6) #ST-5- /2 Split Lockwasher- (6) #ST- 7- /2 Hex Nut- (6) #ST-20- /2 Acorn Nut- (6) #ST- 3-3/8 x 3 /2 Lag Bolt- (8) #ST -3-3/8 USS Flatwasher- (8) UB- UB-2 UB-3 UB-4 ST-20 ST-7 ST-2 ST-5 ST-3 ST-3 ST-9 ST-

30 PARTS #TX-- TX PC Upper Rope Arm- () #TX-6- TX PC Upper Accessory Arm- () Main Assembly Hardware #ST- 9- /2 x 7 Carriage Bolt- (4) #ST-- 3/4 USS Flatwasher- (4) #ST- 2- /2 USS Flatwasher- (4) #ST-5- /2 Split Lockwasher- (4) #ST- 7- /2 Hex Nut- (4) #ST-20- /2 Acorn Nut- (4) #ST- 2-3/8 x 5 Lag Bolt- (4) #ST -3-3/8 USS Flatwasher- (4) TX- TX-6 ST-9 ST- ST-3 ST-2 ST-5 ST-7 ST-20 ST-2

31 Main Assembly PARTS #UB-3- (L) Gusset Bracket- () #UB-4- (R) Gusset Bracket- () #TST-6- Ductile Iron Swing Hangers- (2) Hardware #ST- - 3/8 x 5 Hex Bolt- (4) #ST-3-3/8 USS Flatwasher- (8) #ST- 8-3/8 Bolt Cup- (4) #ST-6-3/8 Split Lockwasher- (4) #ST- 8-3/8 Hex Nut- (4) #ST-9-3/8 Acorn Nut- (4) #ST- 3-3/8 x 3 /2 Lag Bolt- (4) UB-4 UB-3 ST- ST-8 TST-6 ST-8 ST-3 ST-6 ST-3 ST-9 ST-3

32 Main Assembly PARTS #RAIL- Universal Rail- () #UB-8- Universal Rail Bottom- (3) Hardware #ST-4- /4 x 4 /2 Lag Bolt- (6) #ST-4- /4 USS Flatwasher- (8) #ST-5- /4 x 3 Lag Bolt- (2) UB-8 ST-4 ST-4 ST-5 ST-4 ST-4 ST-4

33 PARTS Tarp Assembly #TX-2- TX Playcenter Tarp Board- (2) #TX-3- Universal Tarp Board- () #6PC-0-20 Trapeze Bar (Yellow)- () Trapeze Install Hardware #ST-4- /4 x 4 /2 Lag Bolt- (6) #ST-4- /4 USS Flatwasher- (6) TX-3 TX-2 ST-4 ST-4

34 Rope Ladder Assembly In this step we are connecting the Rope Ladder to the Texan Playcenter Upper Rope Arm and the Texan Playcenter Lower Rope Runner..)Thread the Ladder Ropes through the Texan Playcenter Upper Rope Arm and tie knots. 2.) Slide a Rope Rung up the Ladder Ropes with about 0 - between bottom of the Texan Playcenter Upper Rope Arm and Rope Rung, tie a single knot on each rope, directly below item Rope Rung. 3.) Repeat step 2 for the remaining Rope Rungs with about 0 - between each Rope Rung. In this step we are connecting the Rope Block on the Texan Playcenter Upper Rope Arm and the Texan Playcenter Lower Rope Runner..) Thread the Rockwall Rope through the Rope Block and tie a knot. 2.) Tie 4 knots spaced evenly throughout the length of the Rockwall Rope. 3.)Place the Rockwall Rope through the Texan Playcenter Lower Rope Runner on the back side.

35 Tarp Assembly Figure A. (Figure A.)- Take one corner of the VINYL TARP and place it flush in the corner. Tap the snap with a blunt object, leaving an indention of the snap in the wood. Repeat this process until all the snaps have been indented in the wood on both sides of the Playcenter. Figure B. (Figure B.)- Using the indentions you just made with the snaps, take the 5/8 PHILLIPS SCREW SNAPS and drill one into each indention.

36 Tarp Assembly PARTS #WR-4- TX PC Wood Roof Board- (6) #WR-6- QC PC Wood Roof Runner- (4) 8 Board Roof Panel Hardware #WR-26-5/8 Coated Deck Screws- (64) #WR-4 #WR-6 Place WR-6 to the inner lip of the st Wood Roof Board 5 Gap Repeat this step one more time for 2, 8 Board Roof Panels #WR-26 Take the corner of the VINYL TARP and start placing the snaps on the PHILLIPS SCREW SNAPS. Fold the VINYL TARP over the top of the UNIVERSAL TARP BOARD. Pull tight and place the snaps on the PHILLIPS SCREW SNAPS.

37 8 Board Roof Panel 9 Board Roof Panel PARTS #WR-9- QC PC Wood Roof Center Support- (2) #WR-7- QC PC Wood Roof Runner #2- (4) #WR-5- TX PC Wood Roof Board Ripped- (2) #WR-4- TX PC Wood Roof Board- (6) 32 /4 Gap Hardware #WR-26-5/8 Coated Deck Screws- (42) #WR-5 3/6 Gap #WR-4 5 Gap #WR-9 Repeat this step one more time for 2, 8 Board Roof Panels Repeat this step one more time for 2, 9 Board Roof Panels #WR-26 #WR-26

38 9 Board Roof Panel PARTS #WR-8- QC PC Wood Roof Center Support- (2) #WR0- Universal Center Fan Board- (2) #WR-- Universal PC Bottom Fan Board- (2) Wood Roof Fan Hardware #WR-26-5/8 Coated Deck Screws- (3) 32 /4 Gap #WR-8 9 /8 Gap #WR-0 #WR- Repeat this step one more time for 2, 9 Board Roof Panels Repeat this step one more time for 2, Wood Roof Fans #WR-26 #WR-26

39 PARTS #WR-2- Universal PC Center Fan Board- (2) #WR-3- Uni. PC Long(L) Side Fan Board- (2) #WR-4- Uni. PC Long(R) Side Fan Board- (2) #WR-5- Uni. PC Short (R) Side Fan Board- (2) #WR-6- Uni. PC Short (L) Side Fan Board- (2) Wood Roof Fan Hardware #WR-26-5/8 Coated Deck Screws- (3) #WR-5 #WR-6 #WR-2 25 Gap #WR-4 #WR-3 Repeat this step one more time for 2, Wood Roof Fans #WR-26 #WR-26

40 #WR-3 PARTS #WR-- TX PC Wood Roof Tarp Board- () #WR-2- Uni. PC (L) Wood Roof Support- (2) #WR-3- Uni. PC (R) Wood Roof Support- (2) #WR-2 Wood Roof Assembly Hardware #WR-23-3/8 x 5 Carriage Bolt- (4) #WR-25- /4 x 3 Lag Bolt- (2) #WR-7- /2 USS Flatwasher- (4) #WR-8-3/8 USS Flatwasher- (4) #WR-20-3/8 Split lockwasher- (4) #WR-2-3/8 Hex Nut- (4) #WR-22-3/8 Acorn Nut- (4) #WR-9- /4 USS Flatwasher- (2) #WR- #WR-20 #WR-22 #WR-25 #WR-7 #WR-8 #WR-2 #WR-9 #WR-23

41 PARTS Wood Roof 8 Board Panels- (2) Wood Roof 9 Board Panels- (2) Wood Roof Assembly Hardware #WR-24- /4 x 4 /2 Lag Screw- (24) #WR-9- /4 USS Flatwasher- (24) 8 Board Roof Panel 9 Board Roof Panel #WR-24 #WR-9 #WR-9 #WR-24

42 Wood Roof Fan PARTS #UB-9- Universal Ent. Block- () Wood Roof Fan- (2) Slide Install Hardware #ST-2-3/8 x 5 Lag Bolt- (2) #ST-3-3/8 USS Flatwasher- (2) #WR-25- /4 x 2 Lag Screw- (4) #WR-9- /4 USS Flatwasher- (4) #WR-FAN ST-3 ST-2 #WR-25 #WR-9

43 Slide Install PARTS #TST-4- /4 Playgrip Safety Handles- (4) Safety Handle Install Hardware #ST-6- #4 x /4 Pan Phillips- () #ST- 4- /4 USS Flatwasher- (3) ST-6 ST-4 ST-6

44 Ladder Handle Install PARTS #TST-5- /4 Playgrip Ladder Handles- (2) #5PC-5 or 6-9 Ships Wheel w/ Hardware- () Ships Wheel Install Hardware #ST-7- #4 x /4 Pan Phillips- (4) TST-5 ST-7

45 Telescope Install PARTS #TST-9- Telscope- (4) #TST-0- Tire Swing Eye Bolts- (3) Tire Swing Install

46 PARTS Pencil- () 9/6 Drill Bit- () Tire Swing Assembly Using a pencil or pen mark the holes in the center of the deck. Drill Marked Holes from previous step using a 9/6 bit.

47 Tire Swing Assembly PARTS #5PC-9- Tire Swivel- () Hardware #ST-0- /2 x 4 /2 Carriage Bolt- (2) #ST-- 3/4 USS FLatwasher- (2) #ST-2- /2 USS Flatwasher- (2) #ST-5- /2 Split Lockwasher- (2) #ST-7- /2 Hex Nut- (2) #ST-20- /2 Acorn Nut- (2) ST-0 ST- ST-2 5PC-9 ST-5 ST-7 ST-20

48 Monkey Bar Install Manual Version 0.3 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact Gun Claw Hammeror Rubber Mallet Pliers or Vise Grips 7/6 Deep Well Socket 9/6 Deep Well Socket 3/4 Deep Well Socket /8, /4, and 9/6 Drill Bits Phillips Head Screw Bits An Adult with two Adult Helpers Please familiarize yourself with the install manual, parts/components and general construction process of your new swing set before getting started. Approximate assembly time: 6 to 8 hours. 6 foot unobstructed safety perimeter around swing set recommended. Houston, TX kid STRUCTURES INC.

49 Item No. MBL- MBL-2 MBL-3 MBL-4 MBL-5 MBL-6 MBL-7 MBL-8 MBL-9 MBL-0 Item No. MBB- MBB-2 Item No. MBH- MBH-2 MBH-3 MBH-4 MBH-5 MBH-6 MBH-7 MBH-8 MBH-9 MBH-0 MBH- MBH-2 MBH-3 MBH-4 Part Number Monkey Bar Lumber Part Description Monkey bar (l) Support monkey bar (r) Support Monkey Bar Wood Step Monkey Bar Entrapment Board 96 (l) Monkey Bar Overhead 96 (r) Monkey Bar Overhead (l) Monkey Bar Gusset (R) Monkey bar gusset (R) Gusset Bracket (L) Gusset Bracket Universal Monkey Bar Box Part Number Part Description /4 x 22 Playgrip Tube /4 Playgrip Ladder Handles Universal Monkey Bar Hardware Part Number Part Description 3/4 USS FLatwasher /2 USS Flatwasher 3/8 USS FLatwasher /4 USS FLatwasher /2 Split lockwasher /2 Hex Nut /2 Acorn Nut /2 x 9 Hex Bolt /2 x 7 Carriage bolt 3/8 x 3 /2 Lag Screw /4 x 4 /2 Lag Screw /4 x 3 Lag Screw 2 Metal Tap Screws #4 x 2 Pan Phillips QTY. 4 4 QTY. 6 2 QTY

50 Item No. EMB- EMB-2 EMB-3 EMB-4 EMB-5 EMB-6 EMB-7 EMB-8 EMB-9 EMB-0 Item No. MBB- MBB-2 Item No. EH- EH-2 EH-3 EH-4 EH-5 EH-6 EH-7 EH-8 EH-9 EH-0 EH- EH-2 EH-3 EH-4 Extended Monkey Bar Lumber Part Number Part Description Monkey bar (l) Support monkey bar (r) Support Monkey Bar Wood Step Monkey Bar Entrapment Board 20 (l) Monkey Bar Overhead 20 (r) Monkey Bar Overhead (l) Monkey Bar Gusset (R) Monkey bar gusset (R) Gusset Bracket (L) Gusset Bracket Extended Monkey Bar Box Part Number Part Description /4 x 22 Playgrip Tube /4 Playgrip Ladder Handles Extended Monkey Bar Hardware Part Number Part Description 3/4 USS FLatwasher /2 USS Flatwasher 3/8 USS FLatwasher /4 USS FLatwasher /2 Split lockwasher /2 Hex Nut /2 Acorn Nut /2 x 9 Hex Bolt /2 x 7 Carriage bolt 3/8 x 3 /2 Lag Screw /4 x 4 /2 Lag Screw /4 x 3 Lag Screw 2 Metal Tap Screws #4 x 2 Pan Phillips QTY. 4 4 QTY. 8 2 QTY

51 MBL Monkey Bar (L) Support QTY. Monkey Bar Lumber MBL Monkey Bar (R) Support QTY. MBL Monkey Bar Wood Step QTY. 4 MBL Monkey Bar Ent Board QTY. 4 MBL (L) Monkey Bar Overhead QTY. MBL (R) Monkey Bar Overhead QTY. MBL (L) Monkey Bar Gusset QTY. MBL (R) Monkey Bar Gusset QTY. MBL (R) Gusset Bracket QTY. MBL (L) Gusset Bracket QTY.

52 EMB Monkey Bar (L) Support QTY. Extended Monkey Bar Lumber EMB Monkey Bar (R) Support QTY. EMB Monkey Bar Wood Step QTY. 4 EMB Monkey Bar Ent Board QTY. 4 EMB (L) Monkey Bar Overhead QTY. EMB (R) Monkey Bar Overhead QTY. EMB (L) Monkey Bar Gusset QTY. EMB (R) Monkey Bar Gusset QTY. EMB (R) Gusset Bracket QTY. EMB (L) Gusset Bracket QTY.

53 Monkey Bar Hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) MBH /4 USS FLatwasher QTY. 4 MBH /2 USS FLatwasher QTY. 5 MBH /8 USS FLatwasher QTY. 2 MBH /4 USS FLatwasher QTY. 24 MBH /2 Split Lockwasher QTY. 4 MBH /2 Hex Nut QTY. 4 MBH /2 Acorn Nut QTY. 4 MBH /2 x 9 Hex Bolt QTY. Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

54 Monkey Bar Hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) MBH /2 x 7 Carriage Bolt QTY. 4 MBH /8 x 3 /2 Lag Screw QTY. 2 MBH /4 x 4/2 Lag Screw QTY. 6 MBH /4 x 3 Lag Screw QTY. 4 MBB /4 x 22 Playgrip Tube QTY. 6 Monkey Bar Box MBH Metal Tap Screws QTY. 2 MBH #4 x 2 Pan Phillips QTY. 4 MBB /4 Playgrip Ladder Handles QTY. 2

55 Extended Monkey Bar Hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) MBH /4 USS FLatwasher QTY. 4 MBH /2 USS FLatwasher QTY. 5 MBH /8 USS FLatwasher QTY. 2 MBH /4 USS FLatwasher QTY. 24 MBH /2 Split Lockwasher QTY. 4 MBH /2 Hex Nut QTY. 4 MBH /2 Acorn Nut QTY. 4 MBH /2 x 9 Hex Bolt QTY. Measurement taken from bottom of bolt head to the bottom of bolt

56 Extended Monkey Bar Hdwr. INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) MBH /2 x 7 Carriage Bolt QTY. 4 MBH /8 x 3 /2 Lag Screw QTY. 2 MBH /4 x 4/2 Lag Screw QTY. 6 MBH /4 x 3 Lag Screw QTY. 4 MBB /4 x 22 Playgrip Tube QTY. 8 Monkey Bar Box MBH Metal Tap Screws QTY. 6 MBH #4 x 2 Pan Phillips QTY. 4 MBB /4 Playgrip Ladder Handles QTY. 2

57 parts needed MBL-- Monkey Bar (L) Support- () MBL-2- Monkey Bar (R) Support- () MBL-3- Monkey Bar Wood Step- (4) MBL-4- Monkey Bar Ent. Board- () Monkey Bar Support Ladder Assembly Hardware needed MBH-4- /4 USS Flatwasher- (20) MBH-- /4 x 4 /2 Lag Screw- (6) MBH-2- /4 x 3 Lag Screw- (4) MBL-2 MBL- MBL-3 34 MBL-4 MBH-4 MBH- MBH-2 MBH-4

58 parts needed MBL-5-96 (L) Monkey Bar Overhead- () MBL-6-96 (R) Monkey Bar Overhead- () MBB-- 22 Playgrip Tubes- (6) Monkey Bar Overhead Assembly Hardware needed MBH- 3-2 Metal tap Screws- (2) MBB- MBL-5 Place the 22 Playgrip Tubes in the holes and using a rubber mallet, knock them in until they bottom out. MBL-6 25 MBH-3 Place the (R) Monkey Bar Overheadon the Playgrip Tubes and using a rubber mallet, knock the board down until it bottoms out. Leaving the assembly at 25 wide.

59 parts needed Monkey Bar overhead Assembly- () Support Assembly- () MBL-7- (L) M Bar Gusset- () MBL-8- (R) M Bar Gusset- () Monkey Bar Assembly Adjustment Hole Hardware needed MBH-- 3/4 USS Flatwasher- (2) MBH-5- /2 Split Lockwasher- (2) MBH-2- /2 USS Flatwasher- (2) MBH-6- /2 Hex Nut- (2) MBH-3-3/8 USS Flatwasher- (8) MBH-7- /2 Acorn Nut- (2) MBH-9- /2 x 7 Carriage Bolt- (2) MBH-0-3/8 x 3 /2 Lag Screw- (8) 5.5 & 7 Deck Height MBH-3 MBH-0 5 Deck Height MBL-7 MBL Deck Height MBH-5 MBH-2 MBH-9 MBH- MBH-6 MBH-7 Grab the Monkey Bar Overhead at the rung that is in the center and pull up scissoring the Monkey Bar Overhead and the Monkey Bar Support. Now facing the Monkey Bar Support place your Left Monkey Bar Gusset on the inside of the board and push up until it touches the Monkey Bar Overhead. Have your helper pull out on the Monkey Bar Support until the notches on the Left Monkey Bar Gusset are flat against the Monkey Bar Support and the Monkey Bar Overhead. **Be careful and do not let the assembly scissor back down as this can cause an injury or damage your Monkey Bars.** Place a 3/8 Flatwasher over a 3/8 x 3 /2 Hex Lag Screw and attach the Left Monkey Bar Gusset to the Monkey Bar Overhead and Monkey Bar Support Ladder. Repeat this process on the right side. Now tighten the /2 Hex Nuts, put on the /2 Acorn Nut and lightly tighten. Do not over tighten.

60 5 & 5.5 Fort Monkey Bar Assembly 5 & 5.5 Playcenter M Bar Assembly Hardware needed MBH-- 3/4 USS Flatwasher- (2) MBH-5- /2 Split Lockwasher- (2) MBH-2- /2 USS Flatwasher- (2) MBH-6- /2 Hex Nut- (2) MBH-7- /2 Acorn Nut- (2) MBH-9- /2 x 7 Carriage Bolt- (2) MBH-4- #4 x 2 Pan Phillips- (4) MBH-4- /4 USS Flatwasher- (4) MBH-3-3/8 USS Flatwasher- (4) MBH-0-3/8 x 3 /2 Lag Screw- (4) MBH-2 MBH- MBH-6 MBH-7 Hardware needed MBH-- 3/4 USS Flatwasher- (2) MBH-5- /2 Split Lockwasher- (2) MBH-2- /2 USS Flatwasher- (2) MBH-6- /2 Hex Nut- (2) MBH-7- /2 Acorn Nut- (2) MBH-9- /2 x 7 Carriage Bolt- (2) MBH-4- #4 x 2 Pan Phillips- (4) MBH-4- /4 USS Flatwasher- (4) MBH-3-3/8 USS Flatwasher- (4) MBH-0-3/8 x 3 /2 Lag Screw- (4) MBH-9 MBH- MBH-2 MBH-5 MBH-6 MBH-7 MBH-3 MBH-0 MBH-9 MBH-0 MBH-3 MBH-5 ***This step is only if you purchased a 5 or 5.5 Fort***. Line up Monkey Bar Overhead countersunk holes with the holes below your 6 Hole Facia. Place a 3/4 Flatwasher over a /2 x 7 Carriage Bolt and then insert thru the hole into the countersunk hole in the Monkey Bar Overhead. Place a /2 Washer, /2 Lockwasher over the /2 x 7 Carriage Bolt end inside the Monkey Bar Overhead. Thread the /2 Hex Nut on to the /2 x 7 Carriage Bolt. Repeat this process on the other side. Now tighten the /2 Hex Nuts, put on the /2 Acorn Nut and lightly tighten. Do not over tighten. Place Left Gusset Bracket and attach with 2-3/8 x 3 /2 Hex Lag Screw with 3/8 Flatwashers on them. Repeat this process for the Right Gusset Bracket on other side. Remove the /2 x 7 Carriage Bolt and Hardware from the Corner Post. Then line up Monkey Bar Overhead countersunk holes with the holes in the Playcenter as seen above. Place a /2 Washer over the /2 x 9 Hex Bolt and then insert thru the Front Beam, then thru the Corner Post, and into the countersunk hole in the Monkey Bar Overhead. Place a /2 Washer, /2 Lockwasher over the /2 x 9 Hex Bolt end inside the Monkey Bar Overhead. Thread the /2 Hex Nut on to the /2 x 9 Hex Bolt. Place Right Gusset Bracket and attach with 2-3/8 x 3 /2 Hex Lag Screw with 3/8 Flatwashers on them. MBH-7 MBH-6 MBH-5 MBH-2 MBH- MBH-9 MBH-3 MBH-0 On the other side place a 3/4 Flatwasher over a /2 x 7 Carriage Bolt and then insert thru the hole into the countersunk hole in the Monkey Bar Overhead. Place a /2 Washer, /2 Lockwasher over the /2 x 7 Carriage Bolt end inside the Monkey Bar Overhead. Thread the /2 Hex Nut on to the /2 x 7 Carriage Bolt. Now tighten the /2 Hex Nuts, put on the /2 Acorn Nut and lightly tighten. Do not over tighten. Place Left Gusset Bracket and attach with 2-3/8 x 3 /2 Hex Lag Screw with 3/8 Flatwashers on them.

61 6.4 & 7 Monkey Bar Assembly Hardware needed MBH-- 3/4 USS Flatwasher- (2) MBH-5- /2 Split Lockwasher- (2) MBH-2- /2 USS Flatwasher- (2) MBH-6- /2 Hex Nut- (2) MBH-7- /2 Acorn Nut- (2) MBH-9- /2 x 7 Carriage Bolt- (2) Safety Handle Install Hardware needed MBH-- 3/4 USS Flatwasher- (2) MBH-5- /2 Split Lockwasher- (2) MBH-2- /2 USS Flatwasher- (2) MBH-6- /2 Hex Nut- (2) MBH-7- /2 Acorn Nut- (2) MBH-9- /2 x 7 Carriage Bolt- (2) MBH-4- #4 x 2 Pan Phillips- (4) MBH-4- /4 USS Flatwasher- (4) MBH-9 MBH- MBH-4 MBH-4 MBB-2 MBH-2 MBH-5 MBH-6 4 MBH-7 Set the Monkey Bar overhead on the deck(fort) or line up the bottom of the Monkey Bar Overhead with the top of the Deck(Playcenter) and insert Monkey Bar Overhead in between the Corner Post and the Center Post. Make sure the ends of the Monkey Bar Overhead is flush with the inside of Corner Post and Center Post and then drill (see Figure 2) thru the Monkey Bar Overhead countersinks thru the Corner Post and Center Post. (On a playcenter swingset you will need to remove the Gusset on the Corner Post prior to drilling and then put the Gusset back on once all the Hardware is installed and tightened.) Place a 3/4 Flatwasher over a /2 x 7 Carriage Bolt and then insert thru the hole into the countersunk hole in the Monkey Bar Overhead. Place a /2 Washer, /2 Lockwasher over the /2 x 7 Carriage Bolt end inside the Monkey Bar Overhead. Thread the /2 Hex Nut on to the /2 x 7 Carriage Bolt. Repeat this process on the other side. Now tighten the /2 Hex Nuts, put on the /2 Acorn Nut and lightly tighten. Do not over tighten.

62 Universal Loft Install Manual Version 6.4 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact Gun Claw Hammeror Rubber Mallet Pliers or Vise Grips 7/6 Deep Well Socket 9/6 Deep Well Socket 3/4 Deep Well Socket /8, /4, and 9/6 Drill Bits Phillips Head Screw Bits An Adult with two Adult Helpers Please familiarize yourself with the install manual, parts/components and general construction process of your new swing set before getting started. Approximate assembly time: 6 to 8 hours. 6 foot unobstructed safety perimeter around swing set recommended. Houston, TX kid STRUCTURES INC.

63 When choosing a location for your swing set, always keep your child or children s safety in mind. Here are some recommendations to help you locate and install a safe play area. This play set is designed for the use of 4 occupants who have a combined weight not exceeding 800 pounds on the elevated floor; 3 occupants who have a combined weight of 525 pounds on the swing area; for a total Unit capacity of 5 occupants who have a combined weight of 325. (this weight is not including the picnic table area) On-site adult supervision is required. The swing set should be located on level ground. The stationary components such as ladders and slides are required to be a minimum of six feet from any structure or obstruction such as a fence, garage, house, tree, overhanging branches, electrical wires, clotheslines, etc. Any swinging equipment is also required to be a minimum distance twice the height of the swing beam away from these obstructions or structures as well. The swing set should be located a safe distance from any water hazards, such as a lake, river, bayou, swimming pool, etc. Do not install this residential swing set in a commercial setting. This swing set is not manufactured for commercial usage and will void all warranties. Tree Frogs Wooden Swing Set Factory is not responsible for any damages or injuries resulting from this swing set being used in a commercial setting. Never install this swing set indoors; or over concrete, asphalt, packed earth, grass, carpet or any other hard surface. A fall onto a hard surface can result in serious or fatal injury. The U.S. Consumer Product Safety Commission (CPSC) recommends that you install and maintain a resilient surface under your swing set. The CPSC s Consumer Information Sheet for Playground Surfacing Materials is on the next page. A resilient surface, should be installed after the swing set has been completely assembled according to these instructions. The swing set must rest on solid ground. Please note that this swing set has a maximum fall height of 7. Here are some maintenance tips required to insure safe play on your swing set for years of fun. At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed, swing seats, chains, ladders, slides, rope and wood components for sign of deterioration and replace if necessary. On a yearly basis, we recommend that you coat your swing set with a sealant or preservative. You may also want to spot sand any areas prior to sealing. ** Special note: Although we recommend that you reseal your swing set annually, you may have to touch up the high traffic areas and/or areas that have a high exposure to direct sunlight.** Be sure that the sealant you select is non-toxic and child safe. Your local Tree Frogs Wooden Swing Set Factory dealer may offer a complete power wash and reseal and maintenance program. Do not use line trimmers or weed eaters around your swing set. The line will remove both paint and wood from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited warranty. Remove plastic swing seats and take in doors or do not use when temperature drops below 0 F. Weight Limits for Tree Frogs Swing Sets Fort Platform: 800 Lbs. Total Weight Swing Belts: 75 Lbs. Trapeze: 25 Lbs. Full Bucket Swing: 50 Lbs. toddler Bucket Swing: 50 Lbs. Tire Swing: 25 Lbs. Total Weight Rope Ladder: 75 Lbs. rock Wall: 50 Lbs. All Slides: 25 Lbs. Tree Frogs recommends that the weight limits for all components must not be exceeded. Failure to adhere to these and other safety guidelines could result in damage to the swing set and/or injury to the users. Please keep this install manual for future reference.

64 To insure SAFE PLAY adults must teach children: Not to walk close to, in front of, behind, or between moving items. Not to swing empty swing seats. Not to swing sideways into the path of adjacent swings. Not to use the swing set in a manner other than that for which it is intended. Not to get off the equipment while it is in motion. Not to jump off the tower. Not to stand in the swing seats. Not to swing so high that chains become slack, or above the height of the swing support. Not to jump on a slide. Not to climb on top of the swing support. Not to attach to the swing set any item that is not specifically designed for use with the equipment, such as (but not limited to) jump ropes, clotheslines, pet leashes, cables, and chains. These may become strangulation hazards. To hold on to swings and climbers with both hands. To slide feet first, never head first. To watch for other children while swinging or playing near the swing set. To also insure SAFE PLAY adults must: Limit climbing and swinging heights to each child s ability. Verify that suspended climbing ropes are secured at both ends. Verify that suspended climbing ropes cannot be looped back on themselves. Dress children appropriately for play. Use well-fitted shoes that do not have slippery soles. Avoid ponchos, scarves, hoods, loose fitting clothing, neckties, and any clothing with a drawstring. Serious injury could result should any part of the children s clothing become entangled in the swing set. Do not allow children to play wearing helmets. Remember that children are inventive. When they develop games that are unsafe, be alert and change the rules. IMPORTANT - PLEASE READ As fresh lumber acclimates to its new environment, the natural tendencies of the tree can show itself in the form of checks, or cracks in the lumber. In almost all cases this is normal and it will not affect the structural integrity of your play set. Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, checking or any other physical properties of wood that do not present a safety hazard, are not covered by this warranty. Defects that develop because the product is exposed to extreme climate conditions are not covered by this warranty. Defects that develop as a result of faulty or improper installation of the product are also not covered by this warranty. Most cracks are not warrantable, however if you believe that the integrity of your play set is compromised by this natural occurrence, please contact the Tree Frogs Swing Set Dealer that you purchased your swing set from. We appreciate your purchase and know that you will enjoy your play system for many years to come.

65 Depending on your experience, assembly of our play sets can take as little as 6 hours up to 24 hours, depending on size, after inventory of parts; therefore, we recommend you set aside a full two days for assembly. Identify all of the parts for your play set. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. After everything is laid out, check carefully to ensure all parts are present. Make sure there are no broken boards. Find an area to sort your hardware. It is best to open the hardware on a solid surface so that you do not lose any pieces in the grass. This will save time and familiarize you with all the different pieces in the hardware bag. **Important note: Wood has some natural defects such as knots, surface cracks, etc... We reject parts that are structurally defective. We use a high quality lumber in our structures; however, you should inspect each part for splinters or rough spots and sand them smooth to prevent injury.** After familiarizing yourself with all of the components, read all instructions thoroughly. Reading instructions after you have studied the parts will help you understand more clearly the installation process, and help to eliminate unnecessary mistakes. Pay close attention to the diameter and length of each bolt and screw. Never tighten hardware completely at first. It helps to have some adjustment for bolt alignment while you are attaching parts together. After everything is square, tighten each joint. After the main unit is assembled it is critical that the floor is level and square. If the main frame is not level, the walls and floor will be out of square. After you complete installation, make sure every bolt, screw, and nut is tight, and every board is secure. Wood will expand and contract with the seasons. Place the set on level ground, not less than 6ft from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. All /4 and 3/8 lag bolts must have pre-drilled holes -/2 to 2 deep. Use a /8 drill bit for the /4 lag bolts and /4 drill bit for 3/8 lag bolts. Use pre-drilled holes in facias as a reference for placing lag bolt pilot holes. If a board lifts or rises causing a gap between boards when running in lag bolts or screws, back out the screw or lag bolt and press or apply pressure (but not enough to crack or break board) while re running in the lag bolt or screw in the same hole. Do not over tighten bolts, lag bolts or screws. You can damage boards, break hardware, and/or strip out the hardware. When using hammer do not beat on the hardware, but gently tap it in. Never beat on the wood as it will leave marks. Complete the steps which will be the basic frame of the fort {i.e. four corner posts with base (sand box boards) and deck supports} Position in the most level area chosen for the play set, keeping in mind the location and size of the swing beam, ladder, slides, etc. that extend off the fort. Once the frame is in the final position, check for vertical and horizontal levelness to determine which side(s) will need to be dug into the ground to level the play set. With a shovel, score the ground around the outside edges of the sandbox boards on the high side of the fort. This is the area that will be dug in. Make sure to score deep enough; the scored lines will be your digging template. Push the frame off and away from the scored area, far enough to dig and remove dirt to reach the appropriate depth. Dig a channel along the scored line(s) for the base of the fort (corner post and sandbox boards) to rest into. Dig the channel(s) to the same level depth. The bottom of the channel(s) should be level to each other so your frame doesn t teeter or rock because the channel(s) are uneven. Once you have removed enough grass and dirt, slide/push the frame into the channel(s). Place a level on the vertical and horizontal boards of the frame to determine if enough soil, or too much, was removed. Repeat this process until the basic frame is plumb and level and in its final position before completing the rest of the assembly. Measure to make sure fort is square. ** Important: if you require a channel depth of more than 6, then we recommend you have your play set area professionally graded before completing assembly. **

66 CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS The U.S. Consumer Product Safety Commission (CPSC) estimates that about 00,000 playground equipment related injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall onto a shockabsorbing surface is less likely to cause a serious injury than a fall onto a hard surface. However, it should be recognized that some injuries from falls will occur no matter what playground surfacing material is used. Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Grass may appear to be acceptable, but can turn to hard packed earth in areas of high traffic. Shredded bark mulch, wood chips, or fine gravel are considered to be acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around play equipment. TABLE -CRITICAL HEIGHTS (in feet) OF TESTED MATERIAL MATERIAL UNCOMPRESSED DEPTH COMPRESSED DEPTH 6 Inch 9 Inch 2 Inch 9 inch Wood Chips Double Shredded Bark Mulch Engineered Wood Fibers 6 7 >2 6 Fine Sand Coarse Sand Fine Gravel Medium Gravel Shredded Tires** 0-2 N/A N/A N/A ** This is data from tests conducted by independent testing laboratories on a 6 inch depth of uncompressed shredded tire samples produced by four manufacturers. The test reported critical heights, which varied from 0 feet to greater than 2 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F292. Table should be read as follows: If, for example, uncompressed wood chips are used at a minimum of 6 inches, the Critical Height is 7 feet. If 9 inches of uncompressed wood chips are used, the Critical Height is 0 feet. It should be noted that, for some materials, the Critical Height decreases when the material is compressed. It is recommended that a shock absorbing material should extend a minimum of 6 feet in all directions from the perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure. This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability in your area, and its cost. This information has been extracted from the CPSC publications Playground Surfacing-Technical Information Guide and Handbook for Public Playground Safety. Copies of these reports can be obtained by sending a postcard to: Office of Public Affairs U.S. Consumer Product Safety Commission Washington, D.C Toll-free Hotline: or at

67 Universal Loft- Base Lumber Item No. Part No. Part Description QTY. ulb- ulb-2 ulb-3 ulb-4 ulb-5 ulb-6 ulb-7 ulb-8 ulb-9 ulb-0 ulb- ulb-2 ulb-3 ulb-4 ulb- ulb-2 ulb-3 ulb-4 ulb-5 ulb-6 ulb-7 ulb-8 ulb-9 ulb-0 ulb- ulb-2 ulb-3 ulb-4 60 /4 3 Hole Facia 28 /2 rail spindle 25 Universal Rail Top 25 universal filler 25 deck runner 25 rail bottom 32 deck board 53 top joist 60 /8 tarp center 62.7/8 tarp side facia 32 large deck board 32 6 Hole facia 60 /8 6 hole facia 32 5/6 tarp upright sl- sl-2 sl-3 sl-4 sl-5 sl-6 sl-7 ulwr- ulwr-2 ulwr-3 ulwr-4 ulwr-5 ulwr-6 ulwr-7 ulwr-8 sl- sl-2 sl-3 sl-4 sl-5 sl-6 sl-7 Standard Loft- Lumber 28 spiral slide filler board 32 entrapment facia 25 entrapment board 25 entrapmnet board 4 center upright 46 corner post 25 entrapment block Universal Loft- Wood Roof Lumber ulwr- ulwr-2 ulwr-3 ulwr-4 ulwr-5 ulwr-6 ulwr-7 ulwr-8 6 5/6 Short fan board 8 7/6 center fan board 28 3/4 bottom fan board 37 center support /6 peak support 7/6 fan cap 39 3/8 wood roof supports 62 7/8 wood roof board

68 Universal Loft- Base Hardware Item No. Part No. Part Description QTY. UBH- ubh-2 ubh-3 ubh-4 ubh-5 ubh-6 ubh-7 SLH- slh-2 slh-3 slh-4 slh-5 slh-6 WRH- WRH-2 wrh-3 wrh-4 wrh-5 wrh-6 wrh-7 wrh-8 wrh-9 wrh-0 wrh- wrh-2 ULA /2 coated deck screw /4 x 2 hex lag screw /4 x 3 hex lag screw /4 x 4 /2 hex lag screw 3/8 x 3 /2 hex lag screw /4 uss flatwasher 3/8 uss flatwasher Standard Loft- Hardware /4 x 3 Hex lag screw 3/8 x 3 /2 hex lag screw 3/8 x 5 hex lag screw /4 uss flatwashr 3/8 uss flatwasher 3/8 x 7 hex lag screw Univeral Loft- Wood Roof Hardware /8 Acorn Nut 3/8 x 3 /2 carriage bolt /4 coated deck screw 2 /2 coated deck screw 3/8 hex nut 3/8 x hex nut 3/8 split lockwasher 3/8 4 prong t-nut 3/8 uss flatwasher /2 uss flatwasher 2 coated deck screw /2 coated deck screw Univeral Loft- Accessories binoculars

69 ULB- 60 /4 3 Hole Facia QTY. 2 Universal Loft- Base Lumber ULB-2 28 /2 Rail Spindle QTY. 20 ULB-3 25 Rail Top QTY. 4 ULB-4 25 Universal Filler QTY. 4 ULB-5 25 Deck Runner QTY. 4 ULB-6 25 Rail Bottom QTY. 4 ULB-7 32 Deck Board QTY. 2 ULB-8 53 Top Joist QTY. 2 ULB-9 60 /8 Tarp Center QTY.

70 ULB /8 Tarp Side Facia QTY. 2 Universal Loft- Base Lumber ULB- 32 Large deck Board QTY. 8 ULB Hole Facia QTY. 2 ULB-3 60 /8 6 Hole Facia QTY. 2 ULB /6 Tarp Upright QTY. 2

71 SL- 28 Spiral Slide Filler Board QTY. 2 Standard Loft- Lumber SL-2 32 Entrapment Facia QTY. SL-3 25 Entrapment Board QTY. SL-4 25 Entrapment Board QTY. SL-5 4 Center Upright QTY. 2 SL-6 46 Corner Post QTY. 4 SL-7 25 Entrapment Block QTY. 2

72 ULWR- 6 5/6 Short Fan Board QTY. 4 Universal Loft- Wood Roof Lumber ULWR-2 8 7/6 Center Fan Board QTY. 2 ULWR /4 Bottom Fan Board QTY. 2 ULWR-4 37 Center Support QTY. 2 ULWR-5 /6 Peak Support QTY. 2 ULWR-6 7/6 Fan Cap QTY. 2 ULWR /8 Wood Roof Supports QTY. 4 ULWR /8 Wood Roof Board QTY. 8

73 Universal Loft Base hardware INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) UBH /2" Coated Deck Screw QTY. 20 UBH /4" x 2" Hex Lag Screw QTY. 2 UBH /4" x 3" Hex Lag Screw QTY. 8 UBH /4" x 4 /2" Hex Lag Screw QTY. 24 UBH /8" x 3 /2" Hex Lag Screw QTY. 36 UBH /4" USS Flatwasher QTY. 32 UBH /8" USS Flatwasher QTY. 36 Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

74 Universal Loft Standard hardware INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) SLH /4" x 3" Hex Lag Screw QTY. 4 SLH /4" USS Flatwasher QTY. 4 SLH /8" x 3 /2" Hex Lag Screw QTY. 2 SLH /8" x 5" Hex Lag Screw QTY. 2 SLH /8" USS Flatwsher QTY. 28 SLH /8" x 7" Hex Lag Screw QTY. 4 Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

75 Universal Loft Standard hardware INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) WRH /8" Acorn Nut Plated QTY. 4 WRH /8" x 3 /2" Carriage Bolt QTY. 4 WRH /4" Coated Deck Screw QTY. 8 WRH /2" Coated Deck Screw QTY. 4 WRH /8" Hex Nut QTY. 4 WRH /8" x " Hex Nut QTY. 6 WRH /8" Split Lockwasher QTY. 4 WRH /8" 4 Prong T-Nut QTY. 6 WRH /8" USS Flatwasher QTY. 0 WRH /2" USS Flatwasher QTY. 4 WRH " Coated Deck Screw QTY. 8 Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

76 Universal Loft Standard hardware INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) WRH /2" Coated Deck Screw QTY. 6 Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

77 ULA Telescope QTY. Universal Loft Accessories

78 Parts Needed ULB-8- Top Joist- () ULB-2-6 Hole Facia- () SL-6- Corner Post- (2) Bubble Panel Assembly Hardware Needed UBH-5-3/8 x 3 /2 Hex Lag Screw- (0) UBH-7-3/8 USS Flatwasher- (0) ULB-8 ULB-2 0 3/8 Gap on each side Bubble Panel SL-6 UBH-7 UBH-7 UBH-5 UBH-5

79 Parts Needed ULB-8- Top Joist- () ULB-2-6 Hole Facia- () SL-6- Corner Post- (2) SL-7- Entrapment Block- (2) Loft Entrapment Assembly Hardware Needed UBH-5-3/8 x 3 /2 Hex Lag Screw- (6) UBH-7-3/8 USS Flatwasher- (6) SLH-5-3/8 USS Flatwasher- (4) SLH-6-3/8 x 7 Hex Lag Screw- (4) Fort Gap 7 /6 Playcenter Gap 9 UBH-7 UBH-5 ULB-8 ULB-2 SLH-6 SLH-5 SL-7 SL-6

80 ULB-7 Rail Assemblies (4) Parts Needed ULB-3- Universal Rail Top- (4) ULB-2- Rail Spindle- (20) ULB-6- Rail Bottom- (4) ULB-5- Deck Runner- (4) ULB-7- Deck Board- (2) ULB-- Large Deck Board- (8) Deck Assemblies (2) Hardware Needed UBH-- 2 /2 Coated Deck Screws- (6) There is a 3/6 gap between each deck board. ULB-5 ULB- 2 5/8 Gap 3 /2 Gap on each side UBH- ULB-3 ULB-2 ULB-6 UBH-

81 Parts Needed SL-3- Loft Entrapment Board- () Fort Loft Entrapment Assembly- () Fort st Step Hardware Needed SLH-2-3/8 x 3 /2 Hex Lag Screw- (4) SLH-5-3/8 USS Flatwasher- (8) SLH-3-3/8 x 5 Hex Lag Screw- (4) SL-3 Fort Entrapment Assembly SLH-3 SLH-2 SLH-5 SLH-5

82 SLH-2 Parts Needed SL-3- Loft Entrapment Board- () Playcenter Loft Entrapment Assembly- () Playcenter st Step Hardware Needed SLH-2-3/8 x 3 /2 Hex Lag Screw- (4) SLH-5-3/8 USS Flatwasher- (8) SLH-3-3/8 x 5 Hex Lag Screw- (4) SL-3 Playcenter Entrapment Assembly SLH-3 SLH-5 SLH-5

83 Entrapment Assembly Parts Needed SL-4- Entrapment Board- () SL-3- Entrapment Board- () Entapment Assembly- () Loft with Monkey Bar on Deck st Step Hardware Needed SLH-5-3/8 USS Flatwasher- (2) SLH-3-3/8 x 5 Hex Lag Screw- (4) SLH-2-3/8 x 3 /2 Hex Lag Screw- (8) SL-4 SLH-2 SLH-5 SLH-2 SLH-5 SL-3 SLH-5 SLH-3

84 UBH-4 Parts Needed ULB-4- Universal Filler- (2) Deck Assembly- () SL-5- Loft Center Upright- (2) Universal Loft Assembly Hardware Needed UBH-4- /4 x 4 /2 Hex Lag Screw- (4) SLH-5-3/8 USS Flatwasher- (4) SLH-3-3/8 x 5 Hex Lag Screw- (4) UBH-6- /4 USS Flatwasher- (4) Deck Assembly ULB-4 25 /4 Gap Between Corner Post and center upright SL-5 ULB-4 UBH-6 SLH-5 SLH-3

85 Parts Needed Deck Assembly- () ULB-4- Universal Filler- () Universal Loft Assembly Hardware Needed UBH-4- /4 x 4 /2 Hex Lag Screw- (6) UBH-6- /4 USS Flatwasher- (6) Center the deck between the corner post and upright and lag down Deck Assembly Deck Assembly ULB-4 UBH-6 UBH-6 UBH-4 UBH-4

86 Parts Needed Bubble Assembly- () Universal Loft Assembly 25 /4 Gap Between Center Upright and Bubble Assembly Hardware Needed UBH-4- /4 x 4 /2 Hex Lag Screw- (4) SLH-3-3/8 USS Flatwasher- (4) SLH-5-3/8 x 5 Hex Lag Screw- (4) UBH-6- /4 USS Flatwasher- (4) Bubble Assembly SLH-3 UBH-6 SLH-5 UBH-4 Center the deck between the corner post and upright and lag down

87 Parts Needed ULB-3- Universal 6 Hole Facia- (2) ULB-- Universal 3 Hole Facia- (2) Universal Loft Assembly Hardware Needed UBH-5-3/8 USS Flatwasher- (8) UBH-7-3/8 x 3 /2 Hex Lag Screw- (8) ULB-3 ULB- UBH-5 UBH-5 UBH-7 UBH-7

88 Parts Needed Rail Assembly- (4) Universal Loft Assembly Hardware Needed UBH-4- /4 x 4 /2 Hex Lag Screw- (8) UBH-6- /4 USS Flatwasher- (6) UBH-3- /4 x 3 Hex Lag Screw- (8) Rail Assembly UBH-3 UBH-6 UBH-4 UBH-6

89 Parts Needed ULB-4- Tarp Upright- (2) ULB-9- Tarp Center- () ULB-0- Tarp Side Facia- (2) Universal Loft Tarp Assembly Hardware Needed SLH-5-3/8 USS Flatwasher- (6) SLH-2-3/8 x 3 /2 Hex Lag Screw- (6) UBH-4- /4 x 4 /2 Hex Lag Screw- (2) UBH-6- /4 USS Flatwasher- (2) UBH-- 2 /2 Coated Deck Screw- (8) 24 3/4 Gap on each side ULB-9 ULB-0 ULB-4 UBH-4 UBH- SLH-5 UBH-6 SLH-2

90 Universal Loft Tarp Assembly Take one corner of the VINYL TARP and place it flush in the corner. Tap the snap with a blunt object, leaving an indention of the snap in the wood. Repeat this process until all the snaps have been indented in the wood on both sides of the loft. Using the indentions you just made with the snaps, take the 5/8 PHILLIPS SCREW SNAPS and drill one into each indention. Take the corner of the VINYL TARP and start placing the snaps on the PHILLIPS SCREW SNAPS. Fold the VINYL TARP over the top of the CENTER TARP BOARD. Pull tight and place the snaps on the PHIL- LIPS SCREW SNAPS.

91 Universal Loft Wood Roof Fan Assembly Parts Needed ULWR-7- Loft Wood Roof Support- (4) ULWR-3- Bottom Fan Board- (2) ULWR-2- Center Fan Board- (2) ULWR-- Short Fan Board- (4) ULWR-6- Fan Cap- (2) Universal Loft Wood Roof Assembly Hardware Needed WRH-- 3/8 Acorn Nut- (4) WRH-5-3/8 Hex Nut- (4) WRH-7-3/8 Split Lockwasher- (4) WRH-9-3/8 USS Flatwasher- (4) WRH-0- /2 USS Flatwasher- (4) WRH-2-3/8 x 3 /2 Carriage Bolt- (4) WRH-2- /2 Deck Screw- (2) 9 /8 Gap on each side ULWR-7 8 3/8 Gap on each side Make 2 Universal Loft Wood Roof Fan Assemblies WRH-2 ULWR-3 ULWR-2 WRH-5 ULWR- WRH- WRH-7 WRH-9 ULWR-6 WRH-2 WRH-0

92 Parts Needed ULWR-5- Loft Peak Facia- (2) Loft Fan Assembly- (2) Universal Loft Wood Roof Assembly Hardware Needed WRH-- 2 Coated Deck Screw- (8) WRH-4-2 /2 Coated Deck Screw- (4) WRH-2- /2 Coated Deck Screw- (0) ULWR-5 Fan Assembly WRH- WRH-4 WRH-2

93 Universal Loft Wood Roof Assembly (Repeat for both Sides) Parts Needed ULWR-8- Wood Roof Board- (5) Hardware Needed WRH-9-3/8 Flatwashers- (6) WRH-8-5/6 x 3/8 3 Prong T-Nut-(6) WRH-6-5/6 x Hex Bolt- (6) WRH-2- /2 Coated Deck Screw-(20) ULWR-8 WRH-8 WRH-6 WRH-2 WRH-9

94 Universal Loft Wood Roof Assembly( Repeat for both sides) Parts Needed ULWR-4- Center Support- () ULWR-8- Wood Roof Board- (4) Hardware Needed WRH-2- /2 Coated Deck Screw- (6) WRH-3- /4 Coated Deck Screw- (8) ULWR-4 ULWR-8 WRH-3 WRH-2 WRH-3

95 Universal Loft Wood Roof Assembly

96 5.4 & 7 Deluxe Spiral Slide Install Manual Version 4.4 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact Gun Claw Hammeror Rubber Mallet Pliers or Vise Grips 7/6 Deep Well Socket 9/6 Deep Well Socket 3/4 Deep Well Socket /8, /4, and 9/6 Drill Bits Phillips Head Screw Bits An Adult with two Adult Helpers Please familiarize yourself with the install manual, parts/components and general construction process of your new swing set before getting started. Approximate assembly time: 6 to 8 hours. 6 foot unobstructed safety perimeter around swing set recommended. Houston, TX kid STRUCTURES INC.

97 When choosing a location for your swing set, always keep your child or children s safety in mind. Here are some recommendations to help you locate and install a safe play area. This play set is designed for the use of 4 occupants who have a combined weight not exceeding 800 pounds on the elevated floor; 3 occupants who have a combined weight of 525 pounds on the swing area; for a total Unit capacity of 5 occupants who have a combined weight of 325. (this weight is not including the picnic table area) On-site adult supervision is required. The swing set should be located on level ground. The stationary components such as ladders and slides are required to be a minimum of six feet from any structure or obstruction such as a fence, garage, house, tree, overhanging branches, electrical wires, clotheslines, etc. Any swinging equipment is also required to be a minimum distance twice the height of the swing beam away from these obstructions or structures as well. The swing set should be located a safe distance from any water hazards, such as a lake, river, bayou, swimming pool, etc. Do not install this residential swing set in a commercial setting. This swing set is not manufactured for commercial usage and will void all warranties. Tree Frogs Wooden Swing Set Factory is not responsible for any damages or injuries resulting from this swing set being used in a commercial setting. Never install this swing set indoors; or over concrete, asphalt, packed earth, grass, carpet or any other hard surface. A fall onto a hard surface can result in serious or fatal injury. The U.S. Consumer Product Safety Commission (CPSC) recommends that you install and maintain a resilient surface under your swing set. The CPSC s Consumer Information Sheet for Playground Surfacing Materials is on the next page. A resilient surface, should be installed after the swing set has been completely assembled according to these instructions. The swing set must rest on solid ground. Please note that this swing set has a maximum fall height of 7. Here are some maintenance tips required to insure safe play on your swing set for years of fun. At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed, swing seats, chains, ladders, slides, rope and wood components for sign of deterioration and replace if necessary. On a yearly basis, we recommend that you coat your swing set with a sealant or preservative. You may also want to spot sand any areas prior to sealing. ** Special note: Although we recommend that you reseal your swing set annually, you may have to touch up the high traffic areas and/or areas that have a high exposure to direct sunlight.** Be sure that the sealant you select is non-toxic and child safe. Your local Tree Frogs Wooden Swing Set Factory dealer may offer a complete power wash and reseal and maintenance program. Do not use line trimmers or weed eaters around your swing set. The line will remove both paint and wood from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited warranty. Remove plastic swing seats and take in doors or do not use when temperature drops below 0 F. Weight Limits for Tree Frogs Swing Sets Fort Platform: 800 Lbs. Total Weight Swing Belts: 75 Lbs. Trapeze: 25 Lbs. Full Bucket Swing: 50 Lbs. toddler Bucket Swing: 50 Lbs. Tire Swing: 25 Lbs. Total Weight Rope Ladder: 75 Lbs. Rock Wall: 50 Lbs. All Slides: 25 Lbs. Tree Frogs recommends that the weight limits for all components must not be exceeded. Failure to adhere to these and other safety guidelines could result in damage to the swing set and/or injury to the users. Please keep this install manual for future reference.

98 To insure SAFE PLAY adults must teach children: Not to walk close to, in front of, behind, or between moving items. Not to swing empty swing seats. Not to swing sideways into the path of adjacent swings. Not to use the swing set in a manner other than that for which it is intended. Not to get off the equipment while it is in motion. Not to jump off the tower. Not to stand in the swing seats. Not to swing so high that chains become slack, or above the height of the swing support. Not to jump on a slide. Not to climb on top of the swing support. Not to attach to the swing set any item that is not specifically designed for use with the equipment, such as (but not limited to) jump ropes, clotheslines, pet leashes, cables, and chains. These may become strangulation hazards. To hold on to swings and climbers with both hands. To slide feet first, never head first. To watch for other children while swinging or playing near the swing set. To also insure SAFE PLAY adults must: Limit climbing and swinging heights to each child s ability. Verify that suspended climbing ropes are secured at both ends. Verify that suspended climbing ropes cannot be looped back on themselves. Dress children appropriately for play. Use well-fitted shoes that do not have slippery soles. Avoid ponchos, scarves, hoods, loose fitting clothing, neckties, and any clothing with a drawstring. Serious injury could result should any part of the children s clothing become entangled in the swing set. Do not allow children to play wearing helmets. Remember that children are inventive. When they develop games that are unsafe, be alert and change the rules. IMPORTANT - PLEASE READ As fresh lumber acclimates to its new environment, the natural tendencies of the tree can show itself in the form of checks, or cracks in the lumber. In almost all cases this is normal and it will not affect the structural integrity of your play set. Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, checking or any other physical properties of wood that do not present a safety hazard, are not covered by this warranty. Defects that develop because the product is exposed to extreme climate conditions are not covered by this warranty. Defects that develop as a result of faulty or improper installation of the product are also not covered by this warranty. Most cracks are not warrantable, however if you believe that the integrity of your play set is compromised by this natural occurrence, please contact the Tree Frogs Swing Set Dealer that you purchased your swing set from. We appreciate your purchase and know that you will enjoy your play system for many years to come.

99 Depending on your experience, assembly of our play sets can take as little as 6 hours up to 24 hours, depending on size, after inventory of parts; therefore, we recommend you set aside a full two days for assembly. Identify all of the parts for your play set. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. After everything is laid out, check carefully to ensure all parts are present. Make sure there are no broken boards. Find an area to sort your hardware. It is best to open the hardware on a solid surface so that you do not lose any pieces in the grass. This will save time and familiarize you with all the different pieces in the hardware bag. **Important note: Wood has some natural defects such as knots, surface cracks, etc... We reject parts that are structurally defective. We use a high quality lumber in our structures; however, you should inspect each part for splinters or rough spots and sand them smooth to prevent injury.** After familiarizing yourself with all of the components, read all instructions thoroughly. Reading instructions after you have studied the parts will help you understand more clearly the installation process, and help to eliminate unnecessary mistakes. Pay close attention to the diameter and length of each bolt and screw. Never tighten hardware completely at first. It helps to have some adjustment for bolt alignment while you are attaching parts together. After everything is square, tighten each joint. After the main unit is assembled it is critical that the floor is level and square. If the main frame is not level, the walls and floor will be out of square. After you complete installation, make sure every bolt, screw, and nut is tight, and every board is secure. Wood will expand and contract with the seasons. Place the set on level ground, not less than 6ft from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. All /4 and 3/8 lag bolts must have pre-drilled holes -/2 to 2 deep. Use a /8 drill bit for the /4 lag bolts and /4 drill bit for 3/8 lag bolts. Use pre-drilled holes in facias as a reference for placing lag bolt pilot holes. If a board lifts or rises causing a gap between boards when running in lag bolts or screws, back out the screw or lag bolt and press or apply pressure (but not enough to crack or break board) while re running in the lag bolt or screw in the same hole. Do not over tighten bolts, lag bolts or screws. You can damage boards, break hardware, and/or strip out the hardware. When using hammer do not beat on the hardware, but gently tap it in. Never beat on the wood as it will leave marks. Complete the steps which will be the basic frame of the fort {i.e. four corner posts with base (sand box boards) and deck supports} Position in the most level area chosen for the play set, keeping in mind the location and size of the swing beam, ladder, slides, etc. that extend off the fort. Once the frame is in the final position, check for vertical and horizontal levelness to determine which side(s) will need to be dug into the ground to level the play set. With a shovel, score the ground around the outside edges of the sandbox boards on the high side of the fort. This is the area that will be dug in. Make sure to score deep enough; the scored lines will be your digging template. Push the frame off and away from the scored area, far enough to dig and remove dirt to reach the appropriate depth. Dig a channel along the scored line(s) for the base of the fort (corner post and sandbox boards) to rest into. Dig the channel(s) to the same level depth. The bottom of the channel(s) should be level to each other so your frame doesn t teeter or rock because the channel(s) are uneven. Once you have removed enough grass and dirt, slide/push the frame into the channel(s). Place a level on the vertical and horizontal boards of the frame to determine if enough soil, or too much, was removed. Repeat this process until the basic frame is plumb and level and in its final position before completing the rest of the assembly. Measure to make sure fort is square. ** Important: if you require a channel depth of more than 6, then we recommend you have your play set area professionally graded before completing assembly. **

100 CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS The U.S. Consumer Product Safety Commission (CPSC) estimates that about 00,000 playground equipment related injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall onto a shockabsorbing surface is less likely to cause a serious injury than a fall onto a hard surface. However, it should be recognized that some injuries from falls will occur no matter what playground surfacing material is used. Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Grass may appear to be acceptable, but can turn to hard packed earth in areas of high traffic. Shredded bark mulch, wood chips, or fine gravel are considered to be acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around play equipment. TABLE -CRITICAL HEIGHTS (in feet) OF TESTED MATERIAL MATERIAL UNCOMPRESSED DEPTH COMPRESSED DEPTH 6 Inch 9 Inch 2 Inch 9 inch Wood Chips Double Shredded Bark Mulch Engineered Wood Fibers 6 7 >2 6 Fine Sand Coarse Sand Fine Gravel Medium Gravel Shredded Tires** 0-2 N/A N/A N/A ** This is data from tests conducted by independent testing laboratories on a 6 inch depth of uncompressed shredded tire samples produced by four manufacturers. The test reported critical heights, which varied from 0 feet to greater than 2 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F292. Table should be read as follows: If, for example, uncompressed wood chips are used at a minimum of 6 inches, the Critical Height is 7 feet. If 9 inches of uncompressed wood chips are used, the Critical Height is 0 feet. It should be noted that, for some materials, the Critical Height decreases when the material is compressed. It is recommended that a shock absorbing material should extend a minimum of 6 feet in all directions from the perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure. This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability in your area, and its cost. This information has been extracted from the CPSC publications Playground Surfacing-Technical Information Guide and Handbook for Public Playground Safety. Copies of these reports can be obtained by sending a postcard to: Office of Public Affairs U.S. Consumer Product Safety Commission Washington, D.C Toll-free Hotline: or at

101 Item No. SFB- SLB- SLB-2 SLB-3 SLB-4 SLB-5 SLB-6 SHB- SHB-2 SHB-3 SHB-4 SHB-5 SHB-6 SHB-7 SHB-8 SHK- SHK-2 SHK-3 SHK-4 SHK-5 SHK-6 SC- SC-2 SC-3 SC-4 SC-5 SC-6 SC-7 Loft Spiral Slide Filler Bundle Part Number Part Description Spiral Slide Filler Board Dlx Spiral Slide Legs Bundle Spiral Slide Brace 30 Spiral Slide Brace Left 24 Spiral Slide Leg Right 24 Spiral Slide Leg Right 32 Spiral Slide Leg Left 32 Spiral Slide Leg Dlx Spiral Slide Hardware Bag /2 USS Flatwasher 3/8 uss flatwasher /2 split lockwasher /2 hex nut /2 acorn nut 3/8 x 5 hex lag screw 3/8 x 3 /2 hex lag screw /2 x 3 /2 carriage bolt Dlx Spiral Slide Hardware Kit /8 USS Flatwasher 5/6 Flatwasher 3/8 x /4 Carriage Bolt 5/6 x Hex Bolt 3/8 Nylon Locknut 5/6 Nylon Locknut Dlx Spiral Slide Hardware Kit Slide Component- Slide component-2 slide component-3 slide component-4 slide component-5 slide component-6 Exit Slide component-7 Entrance QTY

102 Loft Spiral Slide Filler Bundle SFB Spiral Slide Filler Board QTY. 2 SLB Spiral Slide Brace QTY. 2 DLX Spiral Slide Legs Bundle SLB Spiral Slide Brace QTY. 2 SLB Left 24 Spiral Slide Leg QTY. SLB Right 24 Spiral Slide Leg QTY. SLB Right 32 Spiral Leg QTY. SLB Left 32 Spiral Leg QTY.

103 DLX. Spiral Slide Hdwr. Bag INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) #SHB /2 USS FLatwasher QTY. 4 #SHB /8 USS Flatwasher QTY. 22 #SHB /2 Split Lockwasher QTY. 4 #SHB /2 Hex Nut QTY. 4 #SHB /2 Acorn Nut QTY. 4 #SHB /8 x 3 /2 Hex Lag Screw QTY. 6 #SHB /8 x 5 Hex Lag Screw QTY. 6 #SHB /2 x 3 /2 Carriage Bolt QTY. 4 Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

104 DLX. Spiral Slide Hdwr. Kit INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) #SHK /8 USS Flatwasher QTY. 2 #SHK-2 5/6 USS Flatwasher QTY. 20 #SHK /8 x /4 Carriage Bolt QTY. 2 #SHK /6 x Hex Bolt QTY. 60 #SHK /8 Nylon Insert Locknut QTY. 2 #SHK-6 5/6 Nylon Insert Locknut QTY. 60 Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

105 SC- Slide Component- QTY. DLX Spiral Slide Components SC-2 Slide Component-2 QTY. SC-3 Slide Component-3 QTY. SC-4 Slide Component-4 QTY. SC-5 Slide Component-5 QTY. SC-6 Slide Component-6 QTY. SC-7 Slide Component-7 QTY.

106 Parts Needed Sub- Assemblies SC-- Slide Component-- () SC-7- Slide Panel- () SLB-- 20 Spiral Slide Brace- (2) SLB-2-30 Spiral Slide Brace- (2) SLB-3-24 (L) Spiral Slide Leg- () SLB-4- (R) 24 Spiral Slide Leg- () SLB-5- (R) 32 Spiral Slide Leg- () SLB-60 (L) Spiral Slide Leg- () Hardware Needed SHK-3-3/8 x /4 Carriage Bolt- (2) SHB-2-3/8 USS Flatwasher-(6) SHK-5-3/8 Nylon Locknut- (2) SHK-- 3/8 USS FLatwasher-(2) SHB-7-3/8 x 3 /2 Hex Lag Bolt- (6) SHK-3 SC-7 SLB- SLB-6 Outer Seam SLB-3 SLB-2 SC- SLB-5 SHK- 3 Gap SHK-5 Inner Seam SLB-2 SLB- SLB-4 STEP: The first thing we need to do is find the inner and outer seam of the slide part. The inner seam will be on the inside of the curve and the outer seam will be on the outside of the curve. Then we are going to line the bottom seam up with the hole in the bottom center of the panel and the top seam to the top center hole of the panel. Then using the SHK-3 (3/8 x /4 Carriage Bolts), the SHK- (3/8 USS Flatwashers), and the SHK-5 (3/8 Nylon Locknuts) we lag down Slide Component- to the Slide Panel. Then our st sub assembly will be done and we can set it to the side for now. SHB- SHB-7

107 Parts Needed SFB-- Spiral Slide Filler Board- (2) Step Assembly- () Main Assembly Hardware Needed /4 x 2 Hex Lag Bolts- (4) w/ Loft Hardware Bundle /4 USS Flatwashers- (4) w/ Loft Hardware Bundle SHK-6-3/8 x 5 Hex Lag Screw- (6) SHK-2-3/8 USS Flatwasher- (6) SFB- SFB- /4 USS Flatwasher /4 x 2 Lag Bolt SHK-2 SHK-6

108 Parts Needed SC-2- Slide Component 2- () SC-3- Slide Component 3- () Main Assembly Hardware Needed SHK-2-5/6 USS Flatwasher- (48) SHK-4-5/6 x Hex Bolt- (24) SHK-6-5/6 Nylon Locknut- (24) Inner Seam SC-2 SC-2 SC- Inner Seam Inner Seam Inner Seam SC-3 Step: Again the first thing we want to do now is find the inner and outer seam of SC-2. The inner seam being on the inside of the curve and the outer seam being on the outside of the curve. When attaching this part to SC- we are going to take the inner seams and line them up, then rotate the SC-2 CLOCKWISE one hole as shown above. Then using (2) SHK-2 s (5/6 Flatwashers), () SHK-4 (5/6 x Hex Bolt), and () SHK-6 (5/6 Nylon Locknut) for each hole we are going to lag down the part. ** Depending on which way the unit is facing the step may be reversed** Step: The first thing we want to do now is find the inner and outer seam of SC-3. The inner seam being on the inside of the curve and the outer seam being on the outside of the curve. When attaching this part to SC-2 we are going to take the inner seams and line them up, then rotate the SC-3 CLOCKWISE one hole as shown above. Then using (2) SHK-2 s (5/6 Flatwashers), () SHK-4 (5/6 x Hex Bolt), and () SHK-6 (5/6 Nylon Locknut) for each hole we are going to lag down the part. ** Depending on which way the unit is facing the step may be reversed**

109 Parts Needed SC-4- Slide Component- 4- () SC-5- Slide Component-5- () Main Assembly Hardware Needed SHK-2-5/6 USS Flatwasher- (48) SHK-4-5/6 x Hex Bolt- (24) SHK-6-5/6 Nylon Locknut- (24) SC-3 SC-4 SC-4 SC-5 Step: Again the first thing we want to do now is find the inner and outer seam of SC-4. The inner seam being on the inside of the curve and the outer seam being on the outside of the curve. When attaching this part to SC-3 we are going to take the inner seams and line them up, then rotate SC-4 COUNTER CLOCKWISE two holes. Then using (2) SHK-2 s (5/6 Flatwashers), () SHK-4 (5/6 x Hex Bolt), and () SHK-6 (5/6 Nylon Locknut) for each hole we are going to lag down the part. ** Depending on which way the unit is facing the step may be reversed** Step: Again the first thing we want to do now is find the inner and outer seam of SC-5. The inner seam being on the inside of the curve and the outer seam being on the outside of the curve. When attaching this part to SC-4 we are going to take the inner seams and line them up, then rotate SC-5 COUNTER CLOCKWISE two holes. Then using (2) SHK-2 s (5/6 Flatwashers), () SHK-4 (5/6 x Hex Bolt), and () SHK-6 (5/6 Nylon Locknut) for each hole we are going to lag down the part. ** Depending on which way the unit is facing the step may be reversed**

110 Parts Needed SC-6- Slide Component 2- () Main Assembly Hardware Needed SHK-2-5/6 USS Flatwasher- (24) SHK-4-5/6 x Hex Bolt- (2) SHK-6-5/6 Nylon Locknut- (2) SC-5 Step: For the SC-6 we want it to be level. Making the exit an exit. To do this we can line up the seams straight up and down like in the very first assembly or we can line up the inner seams of SC-5 and SC-6, then rotate COUNTER CLOCKWISE 2 holes. Then using (2) SHK-2 s (5/6 Flatwashers), () SHK-4 (5/6 x Hex Bolt), and () SHK-6 (5/6 Nylon Locknut) for each hole we are going to lag down the part. Step: To finish the Deluxe Spiral we only have 2 steps left. The first is to take a 9/6 drill bit and drill a hole throught the slide where we will connect it to the pre assembled base from the first page of the asssembly. This can be tricky so its best to take this step and the next step and repeat both for each hole connecting SC-6 to the pre built assembly. Take note that the slide is a hard plastic but it can be streched to complete our mission.

111 Main Assembly SHB-3 SHB-4 SHB-8 SHB- SHB-2 SHB-5 This step needs to be combined with the previous step to ensure this gets done properly. After drilling a 9/6 Hole through the slide we are going to secure it to the base using a SHB-8 (3/8 x 3 /2 Carriage bolt), SHB- (/2 USS Flatwasher), SHB-2 (3/8 USS Flatwasher), SHB-3 (3/8 Split Lockwasher), SHB-4 (3/8 Hex Nut), SHB-5 (3/8 Acorn Nut). We are going to snug the slide to the inside of wall of the corner post. And repeat this step and the previous step until all croners have been drilled and lagged down.