7.4 Mega Texan Install Manual Version 6.16

Transcription

1 7.4 Mega Texan Install Manual Version 6.6 Tools Needed for Assembly Tape Measure 24 Level Angle Square Phillips Screw Driver 3/8 Cordless Drill or Electric Drill 3/8 Drive Ratchet or Electric Impact Gun Claw Hammeror Rubber Mallet Pliers or Vise Grips 7/6 Deep Well Socket 9/6 Deep Well Socket 3/4 Deep Well Socket /8, /4, and 9/6 Drill Bits Phillips Head Screw Bits An Adult with two Adult Helpers Please familiarize yourself with the install manual, parts/components and general construction process of your new swing set before getting started. Approximate assembly time: 6 to 8 hours. 6 foot unobstructed safety perimeter around swing set recommended. HOUSTON, TX KID STRUCTURES INC.

2 When choosing a location for your swing set, always keep your child or children s safety in mind. Here are some recommendations to help you locate and install a safe play area. This play set is designed for the use of 4 occupants who have a combined weight not exceeding 800 pounds on the elevated floor; 3 occupants who have a combined weight of 525 pounds on the swing area; for a total Unit capacity of 5 occupants who have a combined weight of 325. (this weight is not including the picnic table area) On-site adult supervision is required. The swing set should be located on level ground. The stationary components such as ladders and slides are required to be a minimum of six feet from any structure or obstruction such as a fence, garage, house, tree, overhanging branches, electrical wires, clotheslines, etc. Any swinging equipment is also required to be a minimum distance twice the height of the swing beam away from these obstructions or structures as well. The swing set should be located a safe distance from any water hazards, such as a lake, river, bayou, swimming pool, etc. Do not install this residential swing set in a commercial setting. This swing set is not manufactured for commercial usage and will void all warranties. Tree Frogs Wooden Swing Set Factory is not responsible for any damages or injuries resulting from this swing set being used in a commercial setting. Never install this swing set indoors; or over concrete, asphalt, packed earth, grass, carpet or any other hard surface. A fall onto a hard surface can result in serious or fatal injury. The U.S. Consumer Product Safety Commission (CPSC) recommends that you install and maintain a resilient surface under your swing set. The CPSC s Consumer Information Sheet for Playground Surfacing Materials is on the next page. A resilient surface, should be installed after the swing set has been completely assembled according to these instructions. The swing set must rest on solid ground. Please note that this swing set has a maximum fall height of 7. Here are some maintenance tips required to insure safe play on your swing set for years of fun. At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed, swing seats, chains, ladders, slides, rope and wood components for sign of deterioration and replace if necessary. On a yearly basis, we recommend that you coat your swing set with a sealant or preservative. You may also want to spot sand any areas prior to sealing. ** Special note: Although we recommend that you reseal your swing set annually, you may have to touch up the high traffic areas and/or areas that have a high exposure to direct sunlight.** Be sure that the sealant you select is non-toxic and child safe. Your local Tree Frogs Wooden Swing Set Factory dealer may offer a complete power wash and reseal and maintenance program. Do not use line trimmers or weed eaters around your swing set. The line will remove both paint and wood from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited warranty. Remove plastic swing seats and take in doors or do not use when temperature drops below 0 F. Weight Limits for Tree Frogs Swing Sets Fort Platform: 800 Lbs. Total Weight Swing Belts: 75 Lbs. Trapeze: 25 Lbs. Full Bucket Swing: 50 Lbs. Toddler Bucket Swing: 50 Lbs. Tire Swing: 25 Lbs. Total Weight Rope Ladder: 75 Lbs. Rock Wall: 50 Lbs. All Slides: 25 Lbs. Tree Frogs recommends that the weight limits for all components must not be exceeded. Failure to adhere to these and other safety guidelines could result in damage to the swing set and/or injury to the users. Please keep this install manual for future reference.

3 To insure SAFE PLAY adults must teach children: Not to walk close to, in front of, behind, or between moving items. Not to swing empty swing seats. Not to swing sideways into the path of adjacent swings. Not to use the swing set in a manner other than that for which it is intended. Not to get off the equipment while it is in motion. Not to jump off the tower. Not to stand in the swing seats. Not to swing so high that chains become slack, or above the height of the swing support. Not to jump on a slide. Not to climb on top of the swing support. Not to attach to the swing set any item that is not specifically designed for use with the equipment, such as (but not limited to) jump ropes, clotheslines, pet leashes, cables, and chains. These may become strangulation hazards. To hold on to swings and climbers with both hands. To slide feet first, never head first. To watch for other children while swinging or playing near the swing set. To also insure SAFE PLAY adults must: Limit climbing and swinging heights to each child s ability. Verify that suspended climbing ropes are secured at both ends. Verify that suspended climbing ropes cannot be looped back on themselves. Dress children appropriately for play. Use well-fitted shoes that do not have slippery soles. Avoid ponchos, scarves, hoods, loose fitting clothing, neckties, and any clothing with a drawstring. Serious injury could result should any part of the children s clothing become entangled in the swing set. Do not allow children to play wearing helmets. Remember that children are inventive. When they develop games that are unsafe, be alert and change the rules. IMPORTANT - PLEASE READ As fresh lumber acclimates to its new environment, the natural tendencies of the tree can show itself in the form of checks, or cracks in the lumber. In almost all cases this is normal and it will not affect the structural integrity of your play set. Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, checking or any other physical properties of wood that do not present a safety hazard, are not covered by this warranty. Defects that develop because the product is exposed to extreme climate conditions are not covered by this warranty. Defects that develop as a result of faulty or improper installation of the product are also not covered by this warranty. Most cracks are not warrantable, however if you believe that the integrity of your play set is compromised by this natural occurrence, please contact the Tree Frogs Swing Set Dealer that you purchased your swing set from. We appreciate your purchase and know that you will enjoy your play system for many years to come.

4 Depending on your experience, assembly of our play sets can take as little as 6 hours up to 24 hours, depending on size, after inventory of parts; therefore, we recommend you set aside a full two days for assembly. Identify all of the parts for your play set. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. After everything is laid out, check carefully to ensure all parts are present. Make sure there are no broken boards. Find an area to sort your hardware. It is best to open the hardware on a solid surface so that you do not lose any pieces in the grass. This will save time and familiarize you with all the different pieces in the hardware bag. **Important note: Wood has some natural defects such as knots, surface cracks, etc... We reject parts that are structurally defective. We use a high quality lumber in our structures; however, you should inspect each part for splinters or rough spots and sand them smooth to prevent injury.** After familiarizing yourself with all of the components, read all instructions thoroughly. Reading instructions after you have studied the parts will help you understand more clearly the installation process, and help to eliminate unnecessary mistakes. Pay close attention to the diameter and length of each bolt and screw. Never tighten hardware completely at first. It helps to have some adjustment for bolt alignment while you are attaching parts together. After everything is square, tighten each joint. After the main unit is assembled it is critical that the floor is level and square. If the main frame is not level, the walls and floor will be out of square. After you complete installation, make sure every bolt, screw, and nut is tight, and every board is secure. Wood will expand and contract with the seasons. Place the set on level ground, not less than 6ft from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. All /4 and 3/8 lag bolts must have pre-drilled holes -/2 to 2 deep. Use a /8 drill bit for the /4 lag bolts and /4 drill bit for 3/8 lag bolts. Use pre-drilled holes in facias as a reference for placing lag bolt pilot holes. If a board lifts or rises causing a gap between boards when running in lag bolts or screws, back out the screw or lag bolt and press or apply pressure (but not enough to crack or break board) while re running in the lag bolt or screw in the same hole. Do not over tighten bolts, lag bolts or screws. You can damage boards, break hardware, and/or strip out the hardware. When using hammer do not beat on the hardware, but gently tap it in. Never beat on the wood as it will leave marks. Complete the steps which will be the basic frame of the fort {i.e. four corner posts with base (sand box boards) and deck supports} Position in the most level area chosen for the play set, keeping in mind the location and size of the swing beam, ladder, slides, etc. that extend off the fort. Once the frame is in the final position, check for vertical and horizontal levelness to determine which side(s) will need to be dug into the ground to level the play set. With a shovel, score the ground around the outside edges of the sandbox boards on the high side of the fort. This is the area that will be dug in. Make sure to score deep enough; the scored lines will be your digging template. Push the frame off and away from the scored area, far enough to dig and remove dirt to reach the appropriate depth. Dig a channel along the scored line(s) for the base of the fort (corner post and sandbox boards) to rest into. Dig the channel(s) to the same level depth. The bottom of the channel(s) should be level to each other so your frame doesn t teeter or rock because the channel(s) are uneven. Once you have removed enough grass and dirt, slide/push the frame into the channel(s). Place a level on the vertical and horizontal boards of the frame to determine if enough soil, or too much, was removed. Repeat this process until the basic frame is plumb and level and in its final position before completing the rest of the assembly. Measure to make sure fort is square. ** Important: if you require a channel depth of more than 6, then we recommend you have your play set area professionally graded before completing assembly. **

5 CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS The U.S. Consumer Product Safety Commission (CPSC) estimates that about 00,000 playground equipment related injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall onto a shockabsorbing surface is less likely to cause a serious injury than a fall onto a hard surface. However, it should be recognized that some injuries from falls will occur no matter what playground surfacing material is used. Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Grass may appear to be acceptable, but can turn to hard packed earth in areas of high traffic. Shredded bark mulch, wood chips, or fine gravel are considered to be acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around play equipment. TABLE -CRITICAL HEIGHTS (in feet) OF TESTED MATERIAL MATERIAL UNCOMPRESSED DEPTH COMPRESSED DEPTH 6 Inch 9 Inch 2 Inch 9 inch Wood Chips Double Shredded Bark Mulch Engineered Wood Fibers 6 7 >2 6 Fine Sand Coarse Sand Fine Gravel Medium Gravel Shredded Tires** 0-2 N/A N/A N/A ** This is data from tests conducted by independent testing laboratories on a 6 inch depth of uncompressed shredded tire samples produced by four manufacturers. The test reported critical heights, which varied from 0 feet to greater than 2 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F292. Table should be read as follows: If, for example, uncompressed wood chips are used at a minimum of 6 inches, the Critical Height is 7 feet. If 9 inches of uncompressed wood chips are used, the Critical Height is 0 feet. It should be noted that, for some materials, the Critical Height decreases when the material is compressed. It is recommended that a shock absorbing material should extend a minimum of 6 feet in all directions from the perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure. This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability in your area, and its cost. This information has been extracted from the CPSC publications Playground Surfacing-Technical Information Guide and Handbook for Public Playground Safety. Copies of these reports can be obtained by sending a postcard to: Office of Public Affairs U.S. Consumer Product Safety Commission Washington, D.C Toll-free Hotline: or at

6 Playcenter Bundle of 2 Item No. Part No. Part Description QTY. PC- PC-2 PC-3 PC-4 PC-5 PC-6 PC-7 PC UNIVERSAL RAIL BOTTOM UNIVERSAL ROPE BLOCK LEFT GUSSET BRACKET RIGHT GUSSET BRACKET UNIVERSAL ENTRAPMENT BLOCK UNIVERSAL PC CENTER POST (L) PLAYCENTER SUPPORT (R) PLAYCENTER SUPPORT PC2- PC2-2 PC2-3 PC2-4 PC2-5 TEX- TEX-2 TEX-3 TEX-4 TEX-5 TEX-6 7TX- 7TX-2 7TX-3 7TX-4 7TX-5 7TX-6 7TX-7 7TX-8 7TX-9 7TX-0 7TX- Playcenter Bundle 2 of LEFT GUSSET BRACKET RIGHT GUSSET BRACKET UNI. PLAYCENTER CORNER POST UNI. PC. TOP JOIST W/ SWING HOLES UNI. PC. TOP JOIST Texan Playcenter Bundle TX PLAYCENTER CENTER TARP BOARD TX PLAYCENTER TARP BOARD TX PLAYCENTER GROUND RUNNER TX PLAYCENTER LOWER ROPE RUNNER TX PLAYCENTER UPPER ACCESSORY ARM TX PLAYCENTER UPPER ROPE ARM 7.4 Texan Playcenter Bundle TX PC ROCKWALL BOARD -ROCK TX PC ROCKWALL BOARD- BLANK TX PC ROCKWALL BOARD 2- ROCK TX PC ROCKWALL BOARD W/ ROPE HOLE ROPE RUNG WOOD STEP TX PC LEFT WOOD STEP LADDER TX PC CENTER CHAIN/ WOOD STEP LADDER TX PC RIGHT CHAIN LADDER LEG TX PC (R) ROCKWALL LADDER LEG TX PC (L) ROCKWALL LADDER LEG

7 Texan MegaSized Bundle Item No. Part No. Part Description QTY. TXM- TXM-2 TXM-3 TXM-4 TXM-5 TXM PLAYCENTER MEGA RAIL BOTTOM PLAYCENTER MEGA RAIL TOP UNIVERSAL RAIL SPINDLE PLAYCENTER MEGA CENTER POST PLAYCENTER MEGA MAINBEAM TX PLAYCENTER DECK DECK- DECK-2 DECK-3 DECK-4 WR- WR-2 WR-3 WR-4 WR-5 WR-6 WR-7 WR-8 WR-9 WR-0 WR- Texan Playcenter Deck (Count for 3 Total) TEXAN PLAYCENTER DECK BOARD- SLIM TEXAN PLAYCENTER DECK BOARD- WIDE UNIVERSAL DECK RUNNER UNIVERSAL DECK SUPPORT Texan Playcenter Wood Roof Bundle PC FAN BOTTOM PC FAN BOARD # PC FAN BOARD #2 PC FAN BOARD #3 PC FAN CENTER PLATE PC WOOD ROOF CENTER SUPPORT PLAYCENTER (L) WOOD ROOF SUPPORT PLAYCENTER (R) WOOD ROOF SUPPORT TX PLAYCENTER WOOD ROOF TARP BOARD TX PC WOOD ROOF BOARD TX PC WOOD ROOF BOARD- RIPPED

8 Texan Playcenter- Standard Box Item No. Part No. Part Description QTY. TSB- TSB-2 TSB-3 TSB-4 TSB-5 TSB-6 TSB-7 TSB-8 TSB-9 TSB-0 TSB- TSB X 63 CHAIN LADDER- YELLOW /4 X 25 PLAYGRIP TUBE /4 X 50 PLAYGRIP TUBE DUCTILE IRON SWING HANGER PLAYGRIP SAFETY HANDLE PLAYGRIP LADDER HANDLE SWINGBEAM T-BRACKET SWINGBEAM 45 BRACKET TIRE EYE BOLT SPRING CLIPS 0 X 00 MM DISC SWING- YELLOW TELESCOPE Texan Playcenter- Box ( Color Depends on Box: Multi or Green) 7TB- 7TB-2 7TB-3 7TB-4 7TB-5 7TB-6 7TB-7 7TB-8 7TB-9 7TB-0 7TB- 7TB XX XX PLASTISOL COATED CHAIN /4 X 25 PLAYGRIP TUBE DUCTILE IRON SWING HANGER TIRE SWIVEL BROWN SPRING CLIPS 0 X 00MM LARGE ROCKS 9 SHIP S WHEEL 90 CHAINED BELT SWING 20 TRAPEZE BAR W/ RINGS 6 YELLOW ROPE 8 YELLOW ROPE 9 YELLOW ROPE

9 Texan Playcenter- Base Hardware Item No. Part No. Part Description QTY. TBH- TBH-2 TBH-3 TBH-4 TBH-5 TBH-6 TBH-7 TBH-8 TBH-9 TBH-0 TBH- TBH-2 TBH-3 TBH-4 TBH-5 TBH-6 TBH-7 TBH-8 TBH-9 TBH-20 TBH /8 ACORN NUT PLATED /2 ACORN NUT PLATED /2 X 4 /2 CARRIAGE BOLT /2 X 7 CARRIAGE BOLT 2 /2 COATED DECK SCREW /2 HEX NUT 3/8 X 5 HEX BOLT /4 X 3 HEX LAG SCREW /4 X 4 /2 HEX LAG SCREW 3/8 X 3 /2 HEX LAG SCREW 3/8 X 5 HEX LAG SCREW 3/8 NYLON INSERT LOCKNUT #4 X 2 PAN PHILLIPS T/S 3/8 SPLIT LOCKWASHER /2 SPLIT LOCKWASHER /4 USS FLATWASHER 3/8 USS FLATWASHER /2 USS FLATWASHER 3/4 USS FLATWASHER /2 X 6 /2 CARRIAGE BOLT 3/8 BOLT CUP RWH- RWH-2 RWH-3 RWH-4 RWH-5 RWH-6 RWH-7 Texan Playcenter- Rockwall Hardware (+ 7RW) /2 COATED DECK SCREW 3/8 X 3 /2 HEX LAG SCREW 3/8 X 5 HEX LAG SCREW /4 X /4 PAN PHILLIPS M/S /4 4 PRONG T- NUT /4 USS FLATWASHER 3/8 USS FLATWASHER Texan Playcenter- Step/ Combo Ladder Hardware (+7SL) SLH- SLH-2 SLH-3 SLH-4 SLH-5 SLH-6 SLH /4 X 4 /2 HEX LAG SCREW 3/8 X 3 /2 HEX LAG SCREW 3/8 X 5 HEX LAG SCREW #4 X 2 PAN PHILLIPS T/S /4 USS FLATWASHER 3/8 USS FLATWASHER 2 METAL TAP SCREW

10 Texan Playcenter- Swingbeam Hardware (+6SB) Item No. Part No. Part Description QTY. SBH- SBH-2 SBH-3 SBH-4 SBH-5 SBH-6 SBH-7 SBH-8 SBH-9 SBH-0 SBH- SBH-2 SBH-3 SBH-4 SBH-5 SBH-6 SBH-7 SH- SH-2 7RW- 7RW-2 7RW-3 7RW /8 ACORN NUT PLATED /2 ACORN NUT PLATED /2 X 3 /2 CARRIAGE BOLT /2 X 7 CARRIAGE BOLT 3/8 HEX NUT /2 HEX NUT 3/8 X 5 HEX LAG SCREW 3/8 NYLON INSERT LOCKNUT 3/8 SPLIT LOCKWASHER /2 SPLIT LOCKWASHER 3/8 USS FLATWASHER /2 USS FLATWASHER 3/4 USS FLATWASHER 3/8 X 0 HEX BOLT #4 X PAN PHILLIPS T/S /2 X 2 HEX BOLT 3/8 BOLT CUP Texan Playcenter- Slide Hardware #4 X 2 PAN PHILLIPS T/S /4 USS FLATWASHER 7.4 Texan Playcenter- Rockwall Hardware /2 COATED DECK SCREW /4 X /4 PAN PHILLIPS M/S /4 4 PRONG T-NUT /4 USS FLATWASHER Texan Playcenter- Step/ Combo Ladder Hardware 7SL- 7SL-2 7SL /4 X 4 /2 HEX LAG SCREW /4 USS FLATWASHER 2 METAL TAP SCREW 8 8 4

11 Texan Playcenter- Wood Roof Hardware Item No. Part No. Part Description QTY. WRH- WRH-2 WRH-3 WRH-4 WRH-5 WRH-6 WRH-7 WRH-8 WRH-9 WRH-0 WRH- WRH-2 MSH- MSH-2 MSH-3 MSH-4 MSH-5 MSH-6 MSH-7 MSH-8 MSH-9 MSH-0 MSH- MSH /8 ACORN NUT PLATED 3/8 X 5 CARRIAGE BOLT /4 PRIMEGUARD DECK SCREW 3/8 HEX NUT /4 X /2 HEX LAG SCREW /4 X 4 /2 HEX LAG SCREW 3/8 SPLIT LOCKWASHER /4 USS FLATWASHER 3/8 USS FLATWASHER /2 USS FLATWASHER /2 PRIMEGUARD DECK SCREW /2 COATED DECK SCREW Texan Playcenter- MegaSized Hardware /2 ACORN NUT PLATED /2 X 7 CARRIAGE BOLT 2 /2 COATED DECK SCREW /2 HEX NUT /4 X 2 HEX LAG SCREW /4 X 4 /2 HEX LAG SCREW 3/8 X 5 HEX LAG SCREW /2 SPLIT LOCKWASHER /4 USS FLATWASHER 3/8 USS FLATWASHER /2 USS FLATWASHER 3/4 USS FLATWASHER 7.4 Texan Playcenter- Swingbeam Hardware 7SB- 7SB-2 7SB-3 7SB-4 7SB-5 7SB-6 7SB-7 7SB-8 7SB-9 7SB-0 7SB /8 ACORN NUT PLATED /2 X 3 CARRIAGE BOLT 3/8 HEX NUT 3/8 X 5 HEX LAG SCREW 3/8 NYLON INSERT LOCKNUT 3/8 SPLIT LOCKWASHER 3/8 USS FLATWASHER 3/8 X 0 HEX BOLT 3/8 X 0 /2 HEX BOLT /2 X 0 CARRIAGE BOLT 3/8 BOLT CUP

12 Playcenter Bundle of 2 UB Universal Rail Bottom QTY. 3 UB Universal Rope Block UB Left Gusset Bracket QTY. 2 UB Right Gusset Bracket QTY. 2 UB Universal Entrapment Block UB Uni. Playcenter Center Post QTY. 2 UB (L) Playcenter Support Gusset QTY. 2 UB (R) Playcenter Support Gusset QTY. 2

13 Playcenter Bundle 2 of 2 UB Left Gusset Bracket QTY. 3 UB Right Gusset Bracket QTY. 3 UB Universal Playcenter Corner Post UB Top Joist- Swingbeam UB Top Joist

14 Texan Playcenter Bundle TX TX. PC. Center Tarp Board TX TX. PC. Tarp Board QTY. 2 TX TX. PC. Ground Runner TX TX. PC. Lower Rope Runner TX TX. PC. Upper Accessory Arm TX TX. PC. Uppoer Rope Arm

15 Texan Playcenter- Rail Bundle RAIL Universal Rail Picket 5 RAIL UNiversal Rail Bottom QTY. 3 RAIL Universal Rail Top QTY. 3 Texan Playcenter- Deck Bundle DECK Deck Runner DECK Center Deck Support QTY. 2 DECK Deck Board- Wide QTY. 6 DECK Deck Board- Slim QTY. 8

16 7.4 Texan Playcenter Bundle A. 7TX Rock Rockwall Board QTY. 7 7TX Rockwall Board- Blank QTY. 5 7TX Rock Rockwall Board QTY. 5 7TX Rockwall Board w/ Rope Hole 7TX Rope Rung QTY. 8 7TX Ladder Step QTY. 7 7TX Left Wood Step Ladder Leg 7TX (C) Chain & Wood Step Ladder Leg 7TX Right Chain Ladder Leg 7TX (R) Rockwall Ladder Leg 7TX (L) Rockwall Ladder Leg

17 Texan MegaSized Bundle TXM Playcenter Mega Rail Bottom QTY. 8 TXM Playcenter Mega Rail Top TXM Universal Rail Spindle QTY. 8 TXM Playcenter Mega Center Post TXM Playcenter Mega Mainbeam QTY. 2 TXM Texan Playcenter Deck

18 Texan Playcenter Wood Roof Bundle WR PC Fan Bottom QTY. 2 WR PC Fan Board # WR PC Fan Board #2 WR PC Fan Board #3 QTY. 2 WR PC Fan Center Plate QTY. 2 WR PC Wood Roof Center Support QTY. 2 WR Playcenter (L) Wood Roof Support QTY. 2 WR Playcenter (R) Wood Roof Support QTY. 2 WR TX Playcenter Wood Roof Tarp Board WR TX PC Wood Roof Board QTY. 30 WR TX PC Wood Roof Board- Ripped QTY. 2

19 Texan Playcenter- Standard Box TSB x 63 Chain Ladder- Yellow TSB /4 x 25 Playgrip Tube TSB /4 x 50 Playgrip Tube TSB Ductile Iron Swing Hanger QTY. 6 TSB Playgrip Safety Handle TSB Playgrip Ladder Handle QTY. 2 TSB Swingbeam T-Bracket TSB Swingbeam 45 Degree Bracket QTY. 2 TSB Tire Eye Bolt QTY. 3 TSB Spring Clips 0 x 00mm QTY. 9 TSB Disc Swing- Yellow TSB Telescope

20 7.4 Texan Playcenter- Box (Color Depends on Box: Multi or Green) 7TB Plastisol Coated Chain QTY. 3 7TB /4 x 25 Playgrip Tube QTY. 2 7TB Ductile Iron Swing Hangers QTY. 2 7TB Tire Swivel 7TB Spring Clips 0 x 00mm QTY. 2 7TB Large Rocks 7 7TB Ship s Wheel 7TB X 66 Chained Belt Swing QTY. 3 7TB Trapeze Bar w/ Rings 7TB Yellow Rope 7TB Yellow Rope 7TB Yellow Rope

21 TEXAN PLAYCENTER- BASE HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) TBH /8 Acorn Nut Plated TBH /2 Acorn Nut Plated QTY. 22 TBH /2 x 4 /2 Carriage Bolt QTY. 2 TBH /2 x 7 Carriage Bolt TBH /2 Hex Nut QTY. 22 TBH /2 Coated Deck Screw 44 TBH /8 x 5 Hex Nut MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

22 TEXAN PLAYCENTER- BASE HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) TBH /4 x 3 Hex Lag Screw 2 TBH /4 x 4 /2 Hex Lag Screw QTY. 20 TBH /8 x 3 /2 Hex Lag Screw QTY. 28 TBH /8 x 5 Hex Lag Screw QTY. 8 TBH /8 Nylon Insert Locknut TBH #4 x 2 Pan Phillips T/S QTY. 8 TBH /8 Split Lockwasher TBH /2 Split Lockwasher QTY. 22 TBH /4 USS Flatwasher 0 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

23 TEXAN PLAYCENTER- BASE HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) TBH /8 USS Flatwasher 0 TBH /2 USS Flatwasher QTY. 22 TBH /4 USS Flatwasher QTY. 22 TBH /8 Bolt Cup TBH /2 x 6 /2 Carriage Bolt 6 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

24 TEXAN PLAYCENTER- ROCKWALL HARDWARE BAG (+7RW) INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) RWH /2 Coated Deck Screw QTY. 76 RWH /8 x 3 /2 Hex Lag Screw RWH /4 x /4 Pan Phillips M/S QTY. 34 RWH /8 x 5 Hex Nut QTY. 2 RWH /4 4 Prong T-Nut QTY. 34 RWH /4 USS Flatwasher QTY. 34 RWH /8 USS Flatwasher QTY. 6 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

25 TEXAN PLAYCENTER STEP/ COMBO LADDER HARDWARE BAG (+7SL) INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) SLH /4 x 4 /2 Hex Lag Screw QTY. 28 SLH /8 x 3 /2 Hex Lag Screw SLH /8 x 5 Hex Lag Screw QTY. 3 SLH #4 x 2 Pan Phillips T/S QTY. 6 SLH /4 USS Flatwasher QTY. 34 SLH /8 USS Flatwasher QTY. 7 SLH Metal Tap Screw QTY. 9 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

26 TEXAN PLAYCENTER- SWINGBEAM HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) SBH /8 Acorn Nut Plated 0 SBH /2 Acorn Nut Plated QTY. 9 SBH /2 x 3 /2 Carriage Bolt QTY. 2 SBH /8 Hex Nut QTY. 2 SBH /2 x 7 Carriage Bolt QTY. 2 SBH /2 Hex Nut QTY. 9 SBH /8 x 5 Hex Lag Screw QTY. 2 SBH /8 Nylon Insert Locknut QTY. 8 SBH /8 Split Lockwasher 0 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

27 TEXAN PLAYCENTER- SWINGBEAM HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) SBH /2 Split Lockwasher QTY. 9 SBH /8 USS Flatwasher 2 SBH /2 USS Flatwasher 0 SBH /4 USS Flatwasher QTY. 8 SBH #4 x Pan Phillips T/S QTY. 2 SBH /8 x 0 Hex Bolt QTY. 2 SBH /2 x 2 Hex Bolt SBH /8 Bolt Cup 0 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

28 TEXAN PLAYCENTER- WOOD ROOF HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) WRH /8 Acorn Nut Plated WRH /8 x 5 Carriage Bolt WRH /4 Primeguard Deck Screw QTY. 62 WRH /8 Hex Nut WRH /4 x /2 Hex Lag Screw 4 WRH /4 x 4 /2 Hex Lag Screw QTY. 6 WRH /8 Split Lockwasher WRH /4 USS Flatwasher QTY. 20 WRH /8 USS Flatwasher WRH /2 USS Flatwasher MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

29 TEXAN MEGASIZED HARDWARE HARDWARE BAG BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) MSH /2 Acorn Nut Plated MSH /2 x 7 Carriage Bolt MSH /2 Coated Deck Screw QTY. 88 MSH /2 Hex Nut MSH /4 x 2 Hex Lag Screw 6 MSH /4 x 4 /2 Hex Lag Screw 4 MEASUREMENT TAKEN FROM BOTTOM OF BOLT OF BOLT HEAD HEAD TO THE TO BOTTOM THE OF BOTTOM BOLT OF USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

30 TEXAN MEGASIZED HARDWARE HARDWARE BAG BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) MSH /8 x 5 Hex Lag Screw MSH /2 Split Lockwasher MSH /4 USS Flatwasher QTY. 22 MSH /8 USS Flatwasher MSH /2 USS Flatwasher MSH /4 USS Flatwasher MEASUREMENT TAKEN FROM BOTTOM OF BOLT OF BOLT HEAD HEAD TO THE TO BOTTOM THE OF BOTTOM BOLT OF USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

31 7.4 TEXAN PLAYCENTER ROCKWALL HARDWARE BAG INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) 7RW /2 Coated Deck Screw QTY. 20 7RW /4 x /4 Pan Phillips M/S QTY. 8 7RW /4 4 Prong T-Nut QTY. 8 7RW /4 USS Flatwasher QTY Texan Playcenter- Step/ Combo Ladder Hardware 7SL /4 x 4 /2 Hex Lag Screw QTY. 8 7SL /4 USS Flatwasher QTY. 8 7SL Metal Tap Screw MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

32 7.4 TEXAN PLAYCENTER- SWINGBEAM HARDWARE INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) 7SB /8 Acorn Nut Plated QTY. 5 7SB /8 Hex Nut 7SB /8 x 5 Hex Lag Screw 7SB /2 x 3 Carriage Bolt 7SB /8 Nylon Insert Locknut 7SB /8 Split Lockwasher QTY. 5 7SB /8 USS Flatwasher QTY. 6 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

33 7.4 TEXAN PLAYCENTER- HARDWARE SWINGBEAM BAG HARDWARE INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) 7SB /8 x 0 Hex Bolt 7SB /8 x 0 /2 Hex Bolt 2 7SB /2 x 0 Carriage Bolt QTY. 3 MEASUREMENT TAKEN FROM BOTTOM OF BOLT OF BOLT HEAD HEAD TO THE TO BOTTOM THE OF BOTTOM BOLT OF USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

34 7.4 TEXAN PLAYCENTER- SWINGBEAM HARDWARE INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) 7SB /8 Bolt Cup QTY. 5 MEASUREMENT TAKEN FROM BOTTOM OF BOLT HEAD TO THE BOTTOM OF BOLT USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE : SCALE AND CAN BE USED TO MATCH HARDWARE SIZES.

35 7.4 Texan Step/ Chain Ladder Assembly PARTS NEEDED 7TX-6- Wood Step- (7) 7TX-7- Left Wood Step Ladder- () 7TX-8- Center Chain/ Step Ladder- () TSB-3- /4 x 50 Playgrip Tube- () TSB-- 2 x 63 Chain Ladder- () TSB-2- /4 x 25 Playgrip Tube- () 7TB-2- /4 x 25 Playgrip Tube- (2) 7TX-9- Right Chain Ladder Leg- () HARDWARE NEEDED SLH-- /4 x 4 /2 Hex Lag Screw- (28) SLH-5- /4 USS Flatwasher- (28) 7TX-6 7TX-8 TSB-3 7TX-9 TSB- TSB-2 7TB-2 7TX-7 SLH- 53 Across SLH-5

36 PARTS NEEDED TEX-4- TX Playcenter Lower Rope Runner- () 7.4 Texan Step/ Chain Ladder Assembly HARDWARE NEEDED SLH-7-2 Metal Tap Screw- (7) SLH-3-3/8 x 5 Hex Lag Screw- (3) SLH-6-3/8 USS Flatwasher- (3) TEX-4 2 Gap SLH-7 SLH-3 SLH-6

37 PARTS NEEDED PC-3- Left Gusset Bracket- () PC-4- Right Gusset Bracket- () TSB-6- Playgrip Ladder Handle- (2) 7.4 Texan Step/ Chain Ladder Assembly HARDWARE NEEDED SLH-2-3/8 x 3 /2 Hex Lag Screw- (4) SLH-6-3/8 USS Flatwasher- (4) SLH-4- #4 x 2 Pan Phillips T/S- (4) SLH-5- /4 USS Flatwasher- (4) PC-3 TSB-6 PC-4 SLH-4 SLH-5 SLH-6 SLH-2

38 7.4 Texan Rockwall Assembly PARTS NEEDED 7TX-- TX PC Rockwall Board -Rock- (7) 7TX-3-2- Rock Rockwall Board- (5) 7TX-2- Rockwall Board- Blank- (5) 7TX-4- Rockwall Board w/ Rope Hole- () 7TX-- Left Rockwall Leg- () 7TX-0- Right Rockwall Leg- () 7TB-6- Rockwall Rocks- (7) HARDWARE NEEDED RWH-4- /4 x /4 Pan Phillips M/S- (34) RWH-6- /4 USS Flatwasher- (34) RWH-5- /4 4- PRong T-Nut- (34) RWH-- 2 /2 Coated Deck Screw- (76) RWH-6 RWH-4 7TX-3 7TX-0 7TX- 7TX-4 7TX- 7TX-2 7TB-6 RWH-5 7TX- RWH-6 RWH-4 7TX-3 RWH- RWH-5 7TB-6

39 RWH-7 PARTS NEEDED TEX-3- TX PC Ground Runner- () PC-3- Left Gusset Bracket- () PC-4- Right Gusset Bracket- () 7.4 Texan Rockwall Assembly HARDWARE NEEDED RWH-3-3/8 x 5 Hex Lag Screw- (2) RWH-7-3/8 USS Flatwasher- (7) RWH-2-3/8 x 3 /2 Hex Lag Screw- (4) PC-3 TEX-3 2 Gap PC-4 RWH-3 RWH-7 RWH-2

40 TBH-5 PARTS NEEDED Rockwall Assembly- () Ladder Assembly- () TXM-5- Playcenter Mainbeam- (2) Mega Texan Main Assembly HARDWARE NEEDED TBH-4- /2 x 7 Carriage Bolt- (4) TBH-9-3/4 USS Flatwasher- (4) TBH-8- /2 USS Flatwasher- (4) TBH-5- /2 Split Lockwasher- (4) TBH-6- /2 Hex Nut- (4) TBH-2- /2 Acorn Nut Plated- (4) TBH-7-3/8 USS Flatwasher- (6) TBH-0-3/8 USS Flatwasher- (6) Rockwall Assembly TXM-5 Ladder Assembly PC-8 PC-7 TBH-4 TBH-9 TBH-7 TBH-8 TBH-0 TBH-6 TBH-2

41 PARTS NEEDED PC-6- Universal PC Center Post- (2) PC2-3- Universal PC Corner Post- (4) PC2-5- Universal PC Top Joist- () PC2-4- Top Joist w/ Swing Holes- () Mega Texan Main Assembly HARDWARE NEEDED TBH-20- /2 x 6 /2 Carriage Bolt- (2) TBH-9-3/4 USS Flatwasher- (2) TBH-8- /2 USS Flatwasher- (2) TBH-5- /2 SPlit Lockwasher- (2) TBH-6- /2 Hex Nut- (2) TBH-2- /2 Acorn Nut Plated- (2) PC-6 PC2-3 PC2-5 PC2-4 TBH-9 TBH-20 TBH-9 TBH-8 TBH-20 TBH-8 TBH-6 TBH-5 TBH-6 TBH-2 TBH-2 TBH-5

42 PARTS NEEDED DECK-- Deck Board- Slim- (2) DECK-2- Deck Board- Wide- (9) DECK-3- Universal Deck Runner- (6) DECK-4- Universal Deck Support- (3) Mega Texan Main Assembly HARDWARE NEEDED TBH-5-2 /2 Coated Deck Screw- (26) TBH-9- /4 x 4 /2 Hex Lag Screw- (2) TBH-6- /4 USS Flatwasher- (2) DECK-4 DECK- Deck Assembly DECK-3 DECK-2 TBH-5 TBH-9 TBH-6

43 PARTS NEEDED TEX-5- Upper Accessory Arm- () TEX-6- Upper Rope Arm- () Mega Texan Main Assembly HARDWARE NEEDED TBH-20- /2 x 6 /2 Carriage Bolt- (4) TBH-9 & MSH-2-3/4 USS Flatwasher- (8) TBH-8 & MSH-- /2 USS Flatwasher- (8) TBH-5 & MSH-8- /2 Split Lockwasher- (8) TBH-6 & MSH-4- /2 Hex Nut- (8) TBH-2 & MSH-- /2 Acorn Nut Plated- (8) TBH-7 & MSH-0-3/8 USS Flatwasher- (8) TBH- & MSH-7-3/8 x 5 Hex Lag Screw- (8) MSH-2- /2 x 7 Carriage Bolt- (4) TEX-5 TEX-6 TXM-4 TBH-20 TBH-9 TBH-5 TBH-2 MSH-7 MSH-0 MSH-4 MSH-8 MSH-2 TBH-8 TBH-6 TBH-7 TBH- MSH- MSH- MSH-2

44 PARTS NEEDED PC2-- Left Gusset Bracket- (3) PC2-2- Right Gusset Bracket- (3) Mega Texan Main Assembly HARDWARE NEEDED TBH-0-3/8 x 3 /2 Hex Lag Screw- (2) TBH-7-3/8 USS Flatwasher- (2) PC2-2 PC2- PC2-2 PC2- TBH-0 TBH-7 TBH-0 TBH-7

45 PARTS NEEDED TXM-- Mega Rail Bottom- (4) PC-- Universal Rail Bottom- (3) Mega Texan Main Assembly HARDWARE NEEDED MSH-9- /4 USS Flatwasher- (8) MSH-5- /4 x 2 Hex Lag Screw- (8) TBH-6- /4 USS Flatwasher- (6) TBH-8- /4 x 3 Hex Lag Screw- (6) TXM- PC- PC- TXM- PC- TBH-6 MSH-9 MSH-5 TBH-8

46 PARTS NEEDED TXM-2- Mega Rail Top- (4) TXM-- Mega Rail Bottom- (4) TXM-3- Rail Spindle- (8) RAIL-- Rail Top- (3) RAIL-2- Rail Bottom- (3) RAIL-3- Rail Spindle- (5) Small Rail- (4) Mega Texan Main Assembly HARDWARE NEEDED MSH-3-2 /2 Coated Deck Screw- (32) MSH-6- /4 x 4 /2 Hex Lag Screw- (8) MSH-9- /4 USS Flatwasher- (6) MSH-5- /4 x 2 Hex Lag Screw- (8) Small Rail TXM-2 TXM-3 TXM- MSH-3 RAIL-3 RAIL- MSH-9 MSH-5 MSH-6 TBH-5 RAIL-2 MSH-9

47 PARTS NEEDED Large Rail- (3) PC-5- Universal Entrapment Block- () Mega Texan Main Assembly HARDWARE NEEDED TBH-6- /4 USS Flatwasher- (2) TBH-9- /4 x 4 /2 Hex Lag Screw- (6) TBH-8- /4 x 3 Hex Lag Screw- (6) TBH-7-3/8 USS Flatwasher- (2) TBH--3/8 x 5 Hex Lag Screw- (2) Large Rail PC-5 TBH-6 TBH-8 TBH-9 TBH-6 TBH-7 TBH-

48 PARTS NEEDED Slide- () TSB-5- Playgrip Safety Handle- (4) Mega Texan Main Assembly HARDWARE NEEDED SH-- #4 x 2 Pan Phillips T/S- (3) SH-2- /4 USS Flatwasher- (3) TBH-3- #4 x 2 Pan Phillips T/S- (8) TBH-6- /4 USS Flatwasher- (8) TSB-5 TBH-6 SH- TBH-3 SH-2

49 PARTS NEEDED 7TX-5- Rope Rung- (8) 7TB-2-9 Yellow Rope- (3) TSB-4- Ductile Hangers- (2) Mega Texan Main Assembly HARDWARE NEEDED TBH-7-3/8 x 5 Hex Bolt- (4) TBH-2-3/8 Bolt Cup- (4) TBH-7-3/8 USS Flatwasher- (4) TBH-4-3/8 Split Lockwasher- (4) TBH-2-3/8 Nylon Insert Locknut- (4) TBH-- 3/8 Acorn Nut Plated- (4) 7TX-5 TBH-7 TBH-2 TBH- TSB-4 TBH-2 TBH-7 TBH-4 7TB-2 Slide one end of the 7TB-2 Yellow Rope through the Upper Rope Arm and tie a good knot. Then take a Rope Rung and slide it up about a to /2 ft below the Rope Arm and tie knot holding it. Repeat for all Rope Rungs til a knot is tied on the Rope Runner.

50 PARTS NEEDED PC-2- Universal Rope Block- () 7TB-9-20 Trapeze Bar w/ Rings- () TSB-0- Spring Clips 0 x 00 mm- (2) Mega Texan Main Assembly HARDWARE NEEDED TBH-7-3/8 USS Flatwasher- (2) TBH-- 3/8 x 5 Hex Lag Screw- (2) PC-2 7TB-9 TBH-7 TSB-0 TBH-

51 PARTS NEEDED 6TB-8-3 Yellow Rope- () TEX-- Center Tarp Board- () TEX-2- Tarp Board- (2) Mega Texan Main Assembly HARDWARE NEEDED TBH-9-3/8 x 5 Hex Lag Screw- (2) TBH-6-3/8 USS Flatwasher- (2) TEX-2 7TB- TEX- TBH-9 TBH-6 Slide one end the 7TB- Rope through the Rope Block and tie a good knot. Then make a knot about a to /2 ft below the Rope Block, Repeat until you can slip the rope through the rockwall and tie another knot securing the rope.

52 PARTS NEEDED Unit Tarp w/ Hardware- () Mega Texan Main Assembly Take one corner of the VINYL TARP and place it flush in the corner. Tap the snap with a blunt object, leaving an indention of the snap in the wood. Repeat this process until all the snaps have been indented in the wood on both sides of the Playcenter. Using the indentions you just made with the snaps, take the 5/8 PHILLIPS SCREW SNAPS and drill one into each indention. Snap Tarp to the 5/8 Phillips Screw Snaps

53 PARTS NEEDED TSB-9- Tire Eye Bolts- (3) 7TB-- 66 Plastisol Coated Chain- (3) Mega Texan Main Assembly TSB-9 7TB-

54 TBH-8 PARTS NEEDED 7TB-4- Tire Swivel- () Mega Texan Main Assembly TBH-3 TBH-9 Using a pencil or pen mark the holes in the center of the deck. 7TB-4 TBH-5 TBH-6 TBH-2 Drill Marked Holes from previous step using a 9/6 bit.

55 PARTS NEEDED TSB-2- Telescope- () 6TB-5-9 Ship s Wheel- () Mega Texan Main Assembly W HARDWARE NEEDED 7TB-7 TSB-2

56 Base Installation Finished ( For Wood Roof Continue, For Swingbeam see Swingbeam Manual)

57 PARTS NEEDED WR-9- TX PC Wood Roof Tarp Board- () Mega Texan Wood Roof Assembly HARDWARE NEEDED TBH-9- /4 x 4 /2 Hex Lag Screw- (2) TBH-6- /4 USS Flatwasher- (2) Center Tarp Board WR-9 TBH-9 TBH-9 TBH-6 TBH-6 Remove Playcenter Center Tarp Board and Replace with WR-9

58 PARTS NEEDED WR-8- (R) Wood Roof Support- (2) WR-7- (L) Wood Roof Support- (2) WR-0- Wood Roof Board- (4) Mega Texan Wood Roof Assembly HARDWARE NEEDED WRH-2-3/8 x 5 Carriage Bolt- (4) WRH-0- /2 USS Flatwasher- (4) WRH-9-3/8 USS Flatwasher- (4) WRH-7-3/8 Split Lockwasher- (4) WRH-4-3/8 Hex Nut- (4) WRH-- 3/8 Acorn Nut Plated- (4) WRH-- /2 Primeguard Deck Screw- (56) WR-8 WR-7 Repeat for Both Sides of Wood Roof WR-0 WRH-7 WRH-9 WRH-0 WRH-2 WRH-6 WRH-8 WRH- WRH-4 WRH-

59 PARTS NEEDED WR-6- Wood Roof Center Support- (2) Mega Texan Wood Roof Assembly HARDWARE NEEDED WRH-3- /4 Primeguard Deck Screw- (30) WRH-- /2 Primeguard Deck Screw- (64) Repeat for Both Sides of Wood Roof Repeat for Both Sides of Wood Roof WR-6 WRH- WRH-3 WRH-3

60 Mega Texan Wood Roof Assembly PARTS NEEDED WR-4- PC Fan Board #3- (2) WR-2- PC Fan Board #- (4) WR-3- PC Fan Board #2- (4) WR-- PC Fan Bottom- (2) WR-5- PC Fan Center Plate- (2) HARDWARE NEEDED WRH-2- /2 Coated Deck Screw- (40) WRH-- /2 Primeguard Deck Screw- (8) WRH-3- /4 Primeguard Deck Screw- (2) Repeat for Both Sides of Wood Roof WR- Make 2 Wood Roof Fans WR-4 WR-2 WR-3 WR- 28 Space WRH- WRH-3 WRH-2 WR-5

61 PARTS NEEDED Wood Roof Fan- (2) Mega Texan Wood Roof Assembly HARDWARE NEEDED WRH-8- /4 USS Flatwasher- (4) WRH-5- /4 x /2 Hex Lag Screw- (4) Repeat for Both Sides of Wood Roof Wood Roof Fan WRH-8 WRH-5