Assembly Instructions for: JEAN S ULTIMATE SWING SETS
|
|
- Conrad Booth
- 6 years ago
- Views:
Transcription
1 Assembly Instructions for: JEAN S ULTIMATE SWING SETS
2 Thank you for purchasing Forever Redwood patio furniture. Forever Redwood is built by Old-Growth Again Restoration Forestry (OGA). OGA is dedicated to restoration forestry. Sales of patio furniture finance our restoration work in California s Redwood forestlands. Tools required: ½-inch ratchet and a mallet or small hammer. You will need a ladder also and a couple helpers. Box Content: Quantity Description Drawings 2 Frame Legs 1 Main structural timber (5 ¾ x 5 ¾ x 204 ) If ordered with optional steel beam, beam will ship already attached to this part: 1 Roof Frame 1 Floor 4 Triangular Roof Sides 2 Rory s Swing Seats 2 of Each Size Frame Cross Support Braces
3 4 Diagonal Braces 4 Face to face swing posts 4 Bench Armrests 4 Seat Supports 2 Bench Backrests 2 Bench Seats 1 Top board 2 Roof panels Quantity Description 4 Chains 4 Springs 12 Quick links 14 4 x 5/16 bolts, washers, and nuts. 2 9 ½ x 3/8 bolts, washers, and nuts x 3/8 bolts, washers, and nuts ½ x 5/16 bolts, washers, and nuts ½ x 5/16 bolts, washers, and nuts. Only if your Rory s comes with option steel beam 4 5 x 5/16 Carriage Bolts, Washers and Nuts 12 6 ½ x 5/16 Carriage Bolts, Washers and Nuts x 3/8 Carriage Bolts, Washers and Nuts 2 13 x 3/8 Carriage Bolts, Washers and Nuts 14 8 x 2 ½ Stainless Steel Screws 10 8 x 2 Stainless Steel Screws
4 Your furniture was fully assembled in the shop prior to being dismantled for shipping. All the parts fit. The parts that go together have the same numbers written next to the predrilled holes they attach to. Please take the time to align the parts with the numbers. If you are forcing a bolt in, the part may be turned around or not aligned properly. Tap the bolt all the way into the wood to set it, then add a washer and lightly tighten. Don t over tighten or you will crush the redwood. Step 1: Frame legs ship mostly assembled, but closed as shown on left. To finish assembly, first open the frame legs as shown. Step 2: Attach 2 cross supports (9 - ½ and 5-6 ) to a frame leg, line up to match with the predrilled holes as shown. Use 10 x 3 / 8 carriage bolts, add washer and nut and lightly tighten. Repeat this step on the other frame leg. Step 3: Attach two 8-10 ¼ cross supports to the top of each frame leg with two carriage bolts, washers and nuts as shown below. Make sure the numbers written next to the predrilled holes on both pieces match.
5 Step 4: Insert 2 bolts (5 ½ x 3/8) to attach the top of the frame legs as shown below, and remove the top cross support: Remove this top cross support Step 5: Once both frame legs are assembled, place them on their sides to attach the square roof frame. Insert this piece between the frame leg boards as shown: Step 6: Attach the two smallest cross supports to the top of the frame legs with 2 carriage bolts, washers and nuts per support. Lightly tighten. Repeat on other side.
6 Step 7: Attach the main structural timber atop the top support braces of each frame leg to tie the swing structure together. To attach, use a 12 x 3 / 8 carriage bolt from above. Add washer and nut and lightly tighten. NOTE: If your swing comes with option steel beam, follow instructions placed at the end. Step 8: Attach the 4 face to face swing posts to the roof frame with one carriage bolt (6 ½ x 3/8 ), washer and nut per post. Step 9: Attach the floor to the 4 face to face swing posts with one carriage bolt (6 ½ x 3/8 ), washer and nut per post. Match the numbers written next to the predrilled holes on each piece.
7 Step 10: Attach bench seat to backrest with two carriage bolts (3 ½ x 5/16), washers and nuts per side. Then attach both armrest to backrest and both seat supports to the bench seat (one per side) with one carriage bolt, washer and nuts. Repeat this step to assemble the other swing bench. Step 11: Attach the swing bench assemblies to 2 posts each. Match the numbers written next to the predrilled holes on each piece. Use 3 ½ x 5/16 carriage bolts add a washer and nut and lightly tighten. Repeat for other side. Step 12: Attach the support timber to reinforce the connection between the frame legs and main structural timber. Use a 7 x 3 / 8 bolt, add a washer a nut and lightly tighten. Repeat to other side.
8 Step 13: Add the swing seats to the chain. First attach the 4 eyebolts on each swing seat. Then add the hardware provided to thread the eyebolt on one end and the chain on the other. Take a few minutes to adjust the chain height to your preference. We recommend you do not cut off the excess chain because you may want to readjust the heights later. Step 14: If it s being placed on a lawn or undeveloped surface it s a good idea to add a few inch deep layer of drainage rock under each post. This will keep the swing from settling into the ground over the years. Attach the chains into the swing hanging assembly already attached to the main support timber. The swings also come with optional set of springs. The springs attach from the swing hangers. Try them out. It softens the ride and is enjoyed by parents and adults. If the swing is mostly for kids & teens, skip the springs If the swings ever creak, add a dab of grease to the moving mechanism of the hanging hardware once and it will never creak again. Step 15: Attach triangular roof sides to the 8-10 ¼ cross support with 2 carriage bolts, washers and nuts each. Match the numbers written next to the predrilled holes on both pieces, align the holes and attach with bolts. Repeat to other side.
9 Step 16: Attach both roof panels to swing roof sides. Align the predrilled holes and attach with 2 carriage bolts, washers and nuts per side. Step 17: Attach the top board to both roof panels with deck screws to cover the gap between both panels.
10 We offer an optional steel beam support if the swing is to be used in a commercial or semipublic application (heavy use). It is not necessary for standard residential use (although a few of our residential orders also choose to add the beam). If your swing was ordered with the beam, the beam sits atop the main support timber and wraps partially around the front and rear. It attaches with eight bolts (5 x 5 / 16 ) to both the 6x6 main support timber and to the A- frames on either side. Thank you. If you have any questions, please call or us.
(Toll Free); 7am-7pm Pacific Time, Monday-Saturday. Assembly Instructions for: RORY S BIG PLAYGROUND SWING SETS
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday Assembly Instructions for: RORY S BIG PLAYGROUND SWING SETS Thank you for purchasing Forever Redwood patio furniture. Forever Redwood is
More information(Toll Free); 8am-5pm Pacific Time, Monday-Friday. Assembly instructions for: CHAIR SWING SETS
866.332.2403 (Toll Free); 8am-5pm Pacific Time, Monday-Friday Assembly instructions for: CHAIR SWING SETS CONTENT OF BOXES QUANTITY DESCRIPTION DRAWING 2 Posts 2 Swing bases 1 Roof support 4 Diagonal knee
More information; Outside the US: am-7pm Pacific Time, Monday-Saturday. Assembly Instructions for: JHOOLA SWING SETS
866.332.2403; Outside the US: 619.600.5630 7am-7pm Pacific Time, Monday-Saturday Assembly Instructions for: JHOOLA SWING SETS Thank you for purchasing Forever Redwood patio furniture. Forever Redwood is
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday. Assembly instructions for: MARISSA S ADVENTURE LOFTS
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday Assembly instructions for: MARISSA S ADVENTURE LOFTS Thank you for purchasing Forever Redwood patio furniture. Forever Redwood is built by
More information(TOLL FREE); 7am 7pm Pacific Time, Monday-Saturday ASSEMBLY INSTRUCTIONS FOR THE RORY S GIANT PLAYGROUND SWING SET
866.33.403 (TOLL FREE); 7am 7pm Pacific Time, Monday-Saturday ASSEMBLY INSTRUCTIONS FOR THE RORY S GIANT PLAYGROUND SWING SET Qty. 1 4 3 Description Frame Legs Lower Main Support Main Structural Timber
More information(Toll Free); 8am-5pm Pacific Time, Monday-Friday. Assembly instructions for: ATTACHED GARDEN PERGOLA WITH METAL PLAQUES
866.332.2403 (Toll Free); 8am-5pm Pacific Time, Monday-Friday Assembly instructions for: ATTACHED GARDEN PERGOLA WITH METAL PLAQUES CONTENT OF BOXES QUANTITY DESCRIPTION DRAWING 2 Posts 2 Main Knee Braces
More informationAssembly instructions for: HOT TUB ENCLOSURE KITS / HOT TUB PAVILION
Assembly instructions for: HOT TUB ENCLOSURE KITS / HOT TUB PAVILION ASSEMBLY INSTRUCTIONS All Pavilions are completely erected in the shop prior to crating for shipping. All hardware is included. All
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday. Assembly instructions for: WOODEN GARDEN PERGOLAS
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday Assembly instructions for: WOODEN GARDEN PERGOLAS CONTENT OF BOXES QUANTITY DESCRIPTION DRAWING 4 Posts Quantity will vary depending on size
More informationAssembly Instructions
V4-10.15 Assembly Instructions (W x D x H) 1.89m x 1.62m x 1.80m Product Name: Miami Swing Pressure Treated products should not be treated with any other products for the first month. PLEASE KEEP THIS
More information(Toll Free); 8am-5pm Pacific Time, Monday-Friday. Assembly instructions for: DEL NORTE OUTDOOR KITCHEN PAVILIONS
866.332.2403 (Toll Free); 8am-5pm Pacific Time, Monday-Friday Assembly instructions for: DEL NORTE OUTDOOR KITCHEN PAVILIONS CONTENT OF BOXES QUANTITY DESCRIPTION DRAWING 4 Posts 4 Main Knee Braces (strengthen
More informationAssembly instructions for: ATTACHED PAVILION - DEL NORTE ROOF STYLE- WITH METAL PLAQUES
866.332.2403 (Toll Free); 8am-5pm Pacific Time, Monday-Friday Assembly instructions for: ATTACHED PAVILION - DEL NORTE ROOF STYLE- WITH METAL PLAQUES CONTENT OF BOXES QUANTITY DESCRIPTION DRAWING 2 Posts
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday. Assembly instructions for: ARCHED PERGOLAS WITHOUT LATTICE PANELS
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday Assembly instructions for: ARCHED PERGOLAS WITHOUT LATTICE PANELS Quantity Description Drawing 4 Posts 4 Braces(28 ) 4 Shorter Braces (22
More informationVINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS
P a g e 1 VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS Shown: 8' x 12' Vinyl Classic Pergola with 12" Top and Main Runner Spacing The design of this pergola is based on all posts being installed
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday. Assembly instructions for: SUN GAZEBO WITH SLIDING DOORS
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday Assembly instructions for: SUN GAZEBO WITH SLIDING DOORS CONTENT OF BOXES QUANTITY DESCRIPTION DRAWING Quantity will vary Window wall panels
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday RORY'S BIG PLAYGROUND SWING SETS
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday RORY'S BIG PLAYGROUND SWING SETS SPECIFICATIONS: DIMENSIONS & DRAWINGS Rory's Big Playground Swing has 3" x 3" timber framing and a 2 3/4"
More information(Toll Free); 8am-5pm Pacific Time, Monday-Friday. Assembly instructions for: THE ATTACHED PAVILION -STOA ROOF WITH METAL PLAQUES
866.332.2403 (Toll Free); 8am-5pm Pacific Time, Monday-Friday Assembly instructions for: THE ATTACHED PAVILION -STOA ROOF WITH METAL PLAQUES CONTENT OF BOXES QUANTITY DESCRIPTION DRAWING 4 Posts 4 Dual
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday BENCH SWING SETS
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday BENCH SWING SETS SPECIFICATIONS: DIMENSIONS & DRAWINGS Swing itself is 1' 11"H x 2' 4"D. Seat back is 1' 8"H from the top of the seat to
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday CHAIR SWING SETS
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday CHAIR SWING SETS SPECIFICATIONS: Swing itself is 1' 11"H x 2' 4"D. Seat back is 1' 8"H from the top of the seat to the top of the backrest.
More informationROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door
ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are
More informationAssembly instructions for: ATTACHED PAVILION KIT - BACKYARD ROOF STYLE - WITH METAL PLAQUES
866.332.2403 (Toll Free); 8am-5pm Pacific Time, Monday-Friday Assembly instructions for: ATTACHED PAVILION KIT - BACKYARD ROOF STYLE - WITH METAL PLAQUES CONTENT OF BOXES QUANTITY DESCRIPTION DRAWING 2
More information176 S. New Holland Road Gordonville, PA Tel: Fax: Castle Loft
176 S. New Holland Road Gordonville, PA 17529 Tel: 717-768-0066 Fax: 717-768-8569 A S S E M B LY M A N U A L Castle Loft Castle Loft Assembly Manual revised 08/31/05 Dear Customer, Thank you for your purchase
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationOsprey Platform Assembly Guide. Menunkatuck Audubon Society. Rev 1.0
Osprey Platform Assembly Guide Menunkatuck Audubon Society Rev 1.0 1 Menunkatuck Audubon Society is a local chapter of National Audubon Society. We serve the shoreline towns of West Haven, New Haven, East
More informationHow to Build A Porch Swing
How to Build A Porch Swing SUPPLIES USED Tape measure Drill 2.5" Wood Screws 1.5" Wood Screws 2" Finishing nails Hammer (or nail gun if you're lucky) Sand paper/ Electric sander Exterior paint Safety glasses
More informationINSTALLATION MANUAL H A
INSTALLATION MANUAL CABINET RACK CR-43-6 (4-UNIT SIZE) Be sure to read this installation manual thoroughly before installing this Cabinet Rack. For the mounting procedures of the components and the relevant
More information176 S. New Holland Road Gordonville, PA Tel: Fax: Playhouse Loft
176 S. New Holland Road Gordonville, PA 17529 Tel: 717-768-0066 Fax: 717-768-8569 A S S E M B LY M A N U A L Playhouse Loft Playhouse Loft revised 9/6/05 Assembly Manual Dear Customer, Thank you for your
More information176 S. New Holland Road Gordonville, PA Tel: Fax: Summit Tower
176 S. New Holland Road Gordonville, PA 17529 Tel: 717-768-0066 Fax: 717-768-8569 A S S E M B LY M A N U A L Summit Tower Summit Tower Assembly Manual revised 9/07/05 Dear Customer, Thank you for your
More information12, 14 & 16 Wide Enclosure Assembly Guide
www.rmfiberglass.com 12, 14 & 16 Wide Enclosure Assembly Guide RM Products Ltd 1-800-363-0867 www.rmfiberglass.com Table of Contents 1. Handling and Storage page 3 to 5 2. Parts and Tools List page 7 3.
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More informationIndependent Containment System (ICS)
Installing the Independent Containment System (ICS) Complete these instructions to install the Independent Containment System (ICS). Prerequisites This installation requires a team of at least two people.
More informationLOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page
LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit
More informationIt can be either a 2½ seater bench seat (2 adult and a kid), or a 5 seater picnic table.
Page 1 Folding picnic table in both bench-seat and picnic table mode Introduction Description A single bench seat that can be changed into a picnic table with ease. This 'Bench come Picnic Table' is ideal
More informationTS-20KD-1010 LOW PROFILE CARGO SCALE INSTALLATION GUIDE
TS-20KD-1010 LOW PROFILE CARGO SCALE INSTALLATION GUIDE Triner Scale & Mfg. Co., Inc. 8411 Hacks Cross Rd. Olive Branch, MS 38654 Phone: 800-238-0152 Fax: 662-809-2386 Description The Triner Scale Model
More informationMetro Series Sauna. installation instructions
Metro Series Sauna installation instructions Please immediately check for any hidden damage that may have occurred in shipping. If any damage is found you must notify the delivering carrier within seven
More informationImportant safety considerations
Important safety considerations This product is intended for use by children not less than 2 years of age. Warning: possible problems of entrapment could occur if used by children under 2 years of age.
More informationFLOE quick attach & standard sectional dock and leg kits
FLOE quick attach & standard sectional dock and leg kits assembly instructions KIT P/N 510-02550-00 X-SHALLOW KIT P/N 510-02551-00 SHALLOW KIT P/N 510-02552-00 MEDIUM KIT P/N 510-02553-00 DEEP WARNING
More informationINS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER
INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER 6-1/2" 5" 2-7/16" 3-7/16" Ø2-7/8" 4-7/8" 11" 2" 3/16" 1/2" HORSESHOE W/ BAR S P ECIFICATIONS PARTS AND TOOLS Tools Needed Tape Measure Pencil
More informationROCKWELL 4-IN-1 DOOR. Two Panel Door. Half X Door. Z Combination Door. Double X Door
ROCKWE 4-IN-1 DOOR Two Panel Door Half X Door Double X Door Z Combination Door Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials
More informationQwik-Fence Installation Instructions
Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate
More informationModel #SH & CH SH Pine CH Naturaline
Model #SH304-101 & CH304-101 Assembly Manual SH304-101 Pine CH304-101 Naturaline Component Parts A 2 ea. Angled Rail - 2 x 4 x 107-1/8" B 1 ea. Center Angled Rail - 2 x 4 x 107-1/8" C 9 ea. Rock Board
More informationOXYGEN INSTALLATION. Revision date
12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex
More informationINSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER R H
INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER 10.6.2016 PARTS INSTALLATION SPECIFICATIONS AND TOOLS INSTRUCTIONS 2-1/4" 2-7/8 11-3/8" 1/4" 2-1/8 PARTS INSTALLATION AND INSTRUCTIONS TOOLS
More informationASSEMBLY INSTRUCTIONS 10 X14 HIGGINS HARDTOP GAZEBO ITEM# L-GZ212PST-4
3811110 ASSEMBLY INSTRUCTIONS 10 X14 HIGGINS HARDTOP GAZEBO ITEM# L-GZ212PST-4 Parts List Square pole A 4 Round pole B 4 Short arch bar C 4 Long arch bar D 6 Long beam 1 E1 2 Long beam 2 E2 2 Long beam
More informationPATIO INSTALLATION MANUAL
PATIO INSTALLATION MANUAL A few minutes spent reviewing the following instructions will help insure quick and proper assembly. The Patio Sauna Kit will arrive on a stretchwrapped pallet including pre-built
More informationHomecrest Style Sling Standard Chair Installation Instructions
1 Homecrest Style Sling Standard Chair Installation Instructions Tools Required Sheppard Hook Spreader Tool Rubber Mallet 7/16 Ratchet/Wrench OPTIONAL NEW HARDWARE PER CHAIR Although your existing Homecrest
More information6' Wide Premium Greenhouse Benches
6' Wide Premium Greenhouse Benches Premium Greenhouse Bench with Rolling Top 2015 FarmTek All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 112416R6X08 6' W x 3' H x 8'
More informationLocker Pedestal Installation Instructions
Locker Pedestal Installation Instructions LK-PED-INST-0314r1 Parts List Single Pedestal Back to Back Pedestal Horizontal Support Tube TS-169 Post Flange TS-190 Post Cap Fasteners Provided: #8 x ¾ round
More information10 x 10 Flat Top Two Tone Pergola
0 x 0 Flat Top Two Tone Pergola Models: Bordeaux ASSEMBLY GUIDE OPTIONAL ACCESSORIES Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post) Bolt Down Bracket Kit ( for Pergola) Ver.0-00
More information176 S. New Holland Road Gordonville, PA Tel: Fax: Eagles Nest
176 S. New Holland Road Gordonville, PA 17529 Tel: 717-768-0066 Fax: 717-768-8569 A S S E M B LY M A N U A L Eagles Nest Eagles Nest Assembly Manual revised 9/2/05 Dear Customer, Thank you for your purchase
More informationIntroduction. Depending on your kennel project, you may have some or all of the following hardware: Part # Description Part # Description 1468
Introduction Thank you very much for your investment in Mason kennels. We take great pride in providing our customers with the highest quality animal enclosures combined with an enjoyable ordering experience.
More informationAssembly of Deluxe and Ultimate Trays supplied as flat packs
Nov 16, 2011 Assembly of Deluxe and Ultimate Trays supplied as flat packs This instruction is for assembling the Bocar Deluxe and Ultimate Ute trays supplied as flat packs. In general, the assembling trays
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationHeartland Pergola. Assembly Manual
Heartland Pergola Assembly Manual Pergola Assembly Manual Thank you for your purchase of this Pergola This manual is designed to simplify the assembly process, however we recommend having an experienced
More information6' Wide Premium Greenhouse Benches
6' Wide Premium Greenhouse Benches Premium Greenhouse Bench with Stationary Top 2015 FarmTek All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 112416S6X08 6' W x 3' H
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More informationWAREHOUSE HANGER INSTALLATION INSTRUCTIONS R H INS T A L L A TIO N INS T R U C TIO N S
INS T A L L A TIO N INS T R U C TIO N S WAREHOUSE HANGER NOTE: Due to the size and weight of the Warehouse Hanger it is recommended that this Hanger be installed on 3 4 or wider doors. 10.11.2016 2-3/16"
More informationINSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER. If there are any questions, please call (800)
INSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER If there are any questions, please call (800) 255-2591 INSTALLATION INSTRUCTIONS WARNING! Ladder Sections Lock When Closed. Do Not Install or Close
More informationKD Table Base Assembly and Top Attachment Instructions
KD Table Base Assembly and Top Attachment Instructions 4011xx 5000xx 7014xx 8001xx 8206xx Congratulations on the purchase of your Tropitone furniture. Read through all steps before starting assembly. CAUTION:
More information2. Arrange Seat Section and Back Section together as follows:
Hello congratulations on the purchase of your 6 swing. I sincerely hope you enjoy! If you have friends or family that would like to purchase please have them contact me directly at 337-540-6162 or cruzeswingsandthings@yahoo.com.
More informationINSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S ROD IRON SCROLL HANGER R H
INS T A L L A TIO N INS T R U C TIO N S ROD IRON SCROLL HANGER 10.5.2016 2-1- 3/16" 11/16" 8" 8 O 2-7/8 Ø2-7/8" 3-1/2 3-1/2" 12-9/16 12-9/16" PLEASE NOTE: These instructions are specific to a particular
More informationMotorcycle Lift Assembly Instructions
Motorcycle Lift Assembly Instructions Copyright JCS 2009 Rev1M Page 1 Lift Table Assembly Instructions The following pages will assist you in the construction of your Motorcycle Lift Table. You will find
More information100LB WEIGHT BENCH SET SF-BH6510 USER MANUAL
100LB WEIGHT BENCH SET SF-BH6510 USER MANUAL IMPORTANT: Please read this manual carefully before using the product. Retain owner s manual for future reference. For Customer Service, please contact: support@sunnyhealthfitness.com
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More informationADULT ASSEMBLY REQUIRED
ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if you are missing parts, do not return this item to the Retailer Store Please call our customer service number and have your instructions
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More informationSafety Guidelines and Assembly Instructions
Play Action Air Rider TM Safety Guidelines and Assembly Instructions Maximum Weight Limit: 210 pounds We re Here To Help! Call Toll Free 1-888-752-9782 Customer Service: Monday - Friday, 8:00 A.M. to 5:00
More informationBABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms
BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away
More informationFor additional assistance call
The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or
More informationMounting the 6 or 12 Indexer on PRS Gantry Tools
Page 1 Mounting the 6 or 12 Indexer on PRS Gantry Tools About this guide: This document illustrates several options for mounting an indexer onto your ShopBot. You can choose the technique that works best
More informationOPTIONAL PARTS LIST: Installation Instructions VPS TRAMPOLINE PARTS LIST. Lower Frame Support Brace (8) Nuts, bolts, and washers (16 each)
OPTIONAL PARTS LIST: **if you purchased a TDU Bundle system- you will also have a lower frame support box with the following parts included: Lower Frame Support Brace (8) Nuts, bolts, and washers (16 each)
More informationinstallation guide 1 GUIDE#: PWB-wwpontoon-pol-004
f250 pontoon WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This WakeWorks tower fits Pontoon boats with 96 to 102 inch wide beam widths. This measurement is taken from
More informationQuick Hoops Seedling and Micro Green Bench Instruction Manual
Quick Hoops Seedling and Micro Green Bench Instruction Manual 955 Benton Ave., Winslow, ME 04901 Phone: 1-877-564-6697 Fax: 1-800-738-6314 Email: service@johnnyseeds.com Web Site: Johnnyseeds.com This
More informationTITAN INDUSTRIAL RACK 4-FOOT TALL / 3-SHELF
TITAN INDUSTRIAL RACK 4-FOOT TALL / 3-SHELF DXST4500 IMPORTANT: Please read this manual carefully before assembling this storage rack and save it for reference INSTRUCTION MANUAL 3 TABLE OF CONTENTS TECHNICAL
More informationSentinel Electronic Safe Installation Guide
Sentinel Electronic Safe Installation Guide by Rev 07/12/2004 P/N 100020 Table of Contents 1. OVERVIEW...3 2. SAFE INSTALLATION...3 2.1. TOOLS REQUIRED...3 2.2. SELECTING THE MOUNTING LOCATION...3 2.3.
More informationPlayful Platform 29' 29'
R PB 8270 Playful Platform TM check out http://www.swing-n-slide.com/planupdates.htm for updates to these instructions. Option #1 PB 8263 Swing Beam PB 8270 Platform NE 4675L Slide 29' Option #2 PB 8263
More informationRear Mount Installation Instructions
Rear Mount Installation Instructions Ford Transit Low Roof 130 WB Frame Kit Part #: DTC 0809-011 V1.0.10.12.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday PATY S SHOWER BENCHES
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday PATY S SHOWER BENCHES SPECIFICATIONS: DIMENSIONS & DRAWINGS Available Lengths, Comfortable Adult Seating Capacity, Standard Widths and Heights
More informationOne piece folding Bench and Picnic Table by Les Kenny
1 1 2 2 Updated Sept/2014 The author Les Kenny is a retired building contractor. Two "DIY for Kids" books (co-authored with his daughter Roseanne) published in 2004 and 2005 respectively got him started
More informationDouble Beam Freestanding Pergola Installation Guide
Double Beam Freestanding Pergola Installation Guide Patent Pending. Copyright 2011 USAVinyl, LLC - All Rights Reserved The information contained in these instructions are proprietary to USAVinyl, LLC and
More informationTherAdapt Products Inc. (800) phone (866) fax
TherAdapt Products Inc. (800) 261-4919 phone (866) 892-2478 fax www.theradapt.com Feeding Chair- 2-in-1 Booster Seat Please read all of the following information before using this product. TherAdapt Products
More information8 x 8 Flat Top Pergola
A S S E M B L Y G U I D E O P T I O N A L A C C E S S O R Y Bolt Down Bracket Kit Models: Mirage, Mandalay Ver 6/00 Ta b l e o f Co n t e n t s Introduction & Overview......................................................
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationASSEMBLY GUIDE. Barcelona Pergola. 12 X16 (365CMx487CM) VER /01/19
ASSEMBLY GUIDE Barcelona Pergola 12 X16 (365CMx487CM) VER 1.9 04/01/19 GETTING STARTED First off, allow us to say thank you for the investment you have made in our fine pergola. This pergola is designed
More information12ft Octagon Bayside Gazebo Assembly Manual
We recommend reviewing this Assembly Manual thoroughly before starting this project. Become familiar with the tools required and where and when assistants are necessary. If you re planning on finishing
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday ROUND PICNIC TABLES (ATTACHED BENCHES)
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday ROUND PICNIC TABLES (ATTACHED BENCHES) SEATING CAPACITY SPECIFICATIONS: The 4 ft Round Picnic Table with benches is designed for eight adults
More informationC4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS
C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS Thank you for your purchase of the C4 Fabrication s 5th Gen 4Runner Rock Sliders! This product was carefully crafted to ensure a perfect
More informationModern Gatherings 60" TV Console Assembly Instructions
Parts List Page 1 of 6 No. Description Sketch Quantity A Console 1 B Door 1 Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts that may have
More informationModel 209 Fireback Replacement
Model 209 Fireback Replacement Please read all the instructions before you begin the procedure. Confirm that you have all the necessary tools and materials. If you have any questions, technical support
More information104 PORCH SWING ASSEMBLY INSTRUCTIONS
104 PORCH SWING ASSEMBLY INSTRUCTIONS Thank you for purchasing a quality porch swing. The product you have purchased requires some assembly. This item has been carefully inspected before packing to ensure
More informationCONTINUED. BACK & SEAT RAILS: 1. Sort three (3) 2x2x8 pieces. 2. Measure and cut one (1) 61 length from each piece.
# Materials: Quantity Each: Total Quantity: 2x2x8 6 2x4x8 9 4x4x8 2 4x6x8 1 TIPS FOR SUCCESSFUL PREP WORK: Before starting, carefully read through the entire instruction sheet. Refer to the material list
More informationTOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
1 TOOLS REQUIRED: RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RUBBER MALLET FOR INSERTING PANELS 8MM HEX BIT WITH EXTENSION FOR HEX BOLT
More informationCAUTION: Before opening the crate place it flat on its side (not up right as show in the photo) Hardware included for assembling your gazebo:
Octagon Wood Gazebo Kit Contents Hardware included for assembling your gazebo: 5/16" Lag Bolts Use to fasten post to floor 2 1/2" screws Use to fasten joist together fasten posts to outside joist fasten
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday. Square Patio Tables. Square Patio Tables.
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday SPECIFICATIONS: SEATING All tables with Chair seating will come with Ruth Chairs (end chairs with arms and side chairs armless) unless an
More informationAssembly Instructions Eggstreme Chicken Coops
Assembly Instructions Eggstreme Chicken Coops Tools Needed Drill/Driver #2 screwdriver bit Pliers Scissors or wire cutter 3/4 wrench Parts List PO Box 1340 Henderson, TX 75653 800-527-1459 To insure a
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday ROUND PICNIC TABLES (UNATTACHED BENCHES)
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday ROUND PICNIC TABLES (UNATTACHED BENCHES) SEATING CAPACITY SPECIFICATIONS: The 4 ft Round Picnic Table with benches is designed for eight
More informationParts list Instruction guide Warnings Please read carefully before assembling and using product.
Parts list Instruction guide Warnings Please read carefully before assembling and using product. Jet Rail XL Part Number 27377 Tools required for assembly Hammer 9/16 Wrench 3/4 Wrench Ratchet 9/16 Socket
More informationSteel Framed Miter Saw Bench
Steel Framed Miter Saw Bench Version 1.1 How to build Steel Framed Miter Saw Bench With easy to follow step-by-step instructions, you will be able to cut, assemble, and finish your very own steel miter
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday THE SANCTUARY SHOWER BENCHES
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday THE SANCTUARY SHOWER BENCHES SPECIFICATIONS: DIMENSIONS & DRAWINGS They are 14 inches deep, 19 inches tall and 21 inches long (see drawings
More informationBIFOLD FUTON FRAME TRINITY ARM. Seat Rails and Slats x 1. *Note: Use 4pc of 100mm Bolts and 4pc of 60mm Bolts to attach the arms to the Stretchers.
1A Parts in this box. 2pc with extra holes 2pc with extra holes & plastic stoppers Arms x 2 Back Rails and Slats x 1 Full Size: Slat Supports x 6 3pc are longer for the Back deck Back Side Rails x 2 Seat
More information