Metal Roofing & Wall Cladding. Cyclonic Areas. High Wind Velocities
|
|
- Vivian Welch
- 5 years ago
- Views:
Transcription
1 High Wind Velocities The northern coastlines of Australia are frequently battered by high winds and cyclones during the mid to late summer season and the most vulnerable part of any structure is the roof. The suction forces created on the downwind side of the roof rise and fall as the wind gusts and then lulls and this places fatigue stresses on the roof connection. If insufficient retention of the roof exists, fatigue failures occur and the roof will begin to separate. Once the roof is gone there is little chance the rest of the building will survive. The greatest influences on the retention of any roof are effective reinforcing plates under the heads of the roofing screws. 1
2 CYCLONIC ROOF ZIPS The Roof Zips are revolutionary cyclonic roofing fasteners. Fast to install saves time and money. Easy to use - requires less end load pressure. Can be drilled on steep sloping roofs or near the edge of sheeting. Will not cause skidding of the roof profile. Used for fixing applications to timber battens, steel purlins and thin metal battens. Fully covered by the Buildex warranty. Includes ShankGuard. Climaseal 4 coating Available head painted to match all standard Colorbond roofing colours. In addition to screws highlighted below, a full range of cyclonic screws are available upon request. HEX HEAD HEX HEAD WITH SEAL Cyclonic Roof Zips Continues page 3 2
3 CYCLONIC ROOF ZIPS CORRI-LOK CYCLONE ASSEMBLY Application: For fastening corrugated roofing profiles in cyclone prone areas to timber battens and steel purlins*. *Steel purlins up to 1.2mm or 1.0mm lapped purlins & 0.75mm metal battens SQUARE-LOK CYCLONE ASSEMBLY Application: For fastening square rib roofing profiles to timber battens and steel purlins* in cyclone prone areas. *Steel purlins up to 1.2mm or 1.0mm lapped purlins & 0.75mm metal battens RIDGE ASSEMBLY with 25mm Multiseal Assembly Application: For fastening corrugated profiles & ridge capping to timber battens or steel purlins*. Also used to fix square rib roofing profiles and ridge capping to steel purlins*. *Steel purlins up to 1.2mm or 1.0mm lapped purlins & 0.75mm metal battens
4 CYCLONIC TEKS Steel support washers with EPDM seals which are used in assembly with roofing screws for securing metal roofing in cyclone prone areas. Available to fit a wide range of roofing profiles. In addition to screws highlighted below, a full range of cyclonic screws are available upon request. CORRI-LOK Applications: For securing corrugated roofing profiles to steel purlins SQUARE-LOK Applications: For securing square rib roofing profiles to steel purlins Cyclonic Teks Continues page 5 4
5 CYCLONIC TEKS HIGH RIB PROFILES Applications: For securing High-rib roofing profiles (Kliplok or equivalent) to steel purlins RIDGE ASSEMBLY with 25mm Multiseal Assembly Washer Applications: For ridge cap assembly of roofing profiles to steel purlins
6 TYPE 17s CYCLONIC SCREWS Cyclone Assemblies are available to fit a wide range of roofing profiles. In addition to screws highlighted below, a full range of cyclonic screws are available upon request. CORRI-LOK Applications: For securing corrugated roofing profiles to timber battens SQUARE-LOK Applications: For securing square rib roofing profiles to timber battens Type 17 s Cyclonic Screws Continues page 7 6
7 TYPE 17s CYCLONIC SCREWS HIGH RIB PROFILES Applications: For fastening High rib roofing profiles (Kliplok or equivalent) to timber battens RIDGE ASSEMBLY with 25mm Multiseal Assembly Washer Applications: For ridge cap assembly of roofing profiles to timber battens
TRUE OAK CORRUGATED SERIES
TRUE OAK CORRUGATED SERIES For too many years architects, builders and roofers have had limited choices in roofing and material options. Until now. In an industry starved of innovation, Revolution Roofing
More information2 ½ Corrugated Panel Installation Specifications
2 ½ Corrugated Panel Installation Specifications ROOF APPLICATION: Roof slope must be a minimum of a 2/12 pitch to use this product. When using this product butyl lap sealant is recommended for all slopes.
More informationS-Rib Corrugated. Tough and Timeless in Every Sense
S-Rib Corrugated Tough and Timeless in Every Sense Fielders S-Rib Corrugated. Tough. And timeless in every sense. A reliable product that stands the test of time, Fielders S-Rib Corrugated can be used
More informationTuff Rib Panel Installation Specifications
Tuff Rib Panel Installation Specifications ROOF APPLICATION: Roof slope must be a minimum of a 2/12 pitch to use this product. For slopes lower than a 3/12 pitch, lap sealant is suggested on the side laps
More informationPBR Panel Installation Specifications
4906 St. Stephens Rd. 5780 Hwy 90 W Eight Mile, Al 36613 Theodore, AL 36590 251 456 2254 251 653 1550 251 457 2254(F) 251 653 1514(F) PBR Panel Installation Specifications ROOF APPLICATION: Roof slope
More informationLYSAGHT FIRMLOK. Identification The format of the number code is: Material specifications
LYSGHT FIRMLOK W = 47 W = 47 2t W = 47 2t D = 200 2t D = 150 D = 100 t t t F100 F150 F200 Sizes Section Dimensions Metal thickness Section area Mass (Colorbond) D x W t ( mm) ( mm) 2 ) ( mm (kg/m) 100
More informationHOBSON. Cyclone Testing THE. In This Issue: Volume 30
THE HOBSON Volume 30 From the desk of Peter Hobson Cyclone Testing Universal Multi-Seal Cyclone Assembly Hobson Engineering (HEC) are extending our screw range to incorporate the HEC Universal Multi-Seal
More informationDesign & Install Guide. The New Standard for Commercial Roof Laps. End-Lap Solution for Insulated Panel Roofing AS WEATHER RESISTANCE
End-Lap Solution for Insulated Panel Roofing AS4046.9 WEATHER RESISTANCE The New Standard for Commercial Roof Laps SecureLap provides a solution to the troublesome sheet to sheet endlap and offers a real
More informationFinesse Profiles. Nailstrip
Installation Details Profile and Lap Detail 265/465 38mm NAILSTRIP *other widths available CD GRADE PLYWOOD 19mm STRUCTURE SILICONE * MIN 20mm VENTILATION GAP * WHEN ROOF PITCH IS UNDER 7.5 OR TOTAL COMBINED
More informationPRODUCT EVALUATION Effective July 1, 2009 RC-204
TEXAS DEPARTMENT OF INSURANCE Engineering Services / MC 103-3A 333 Guadalupe Street P.O. Box 149104 Austin, Texas 78714-9104 Phone No. (512) 322-2212 Fax No. (512) 463-6693 PRODUCT EVALUATION Effective
More informationSHED PACK Step 1: Choose your shed type.
SHED PACK Step 1: Choose your shed type. Industrial Shed Open FarmShed Shed Pack / Types of Sheds Drawing # S0104.A001 Hanger Shed =DISCLAIMER= Please read and agree to Purlin Brackets Terms and Conditions
More informationWALLING SOLUTIONS DESIGN AND INSTALLATION GUIDE
WALLING SOLUTIONS DESIGN AND INSTALLATION GUIDE EASYCLAD CUSTOM ORB MINI ORB MULTICLAD PANELRIB SPANDEK TRIMDEK TRIMWALL WALLCLAD WALLING SOLUTIONS All LYSAGHT roof claddings can be used f both roofing
More informationInstallation Procedures
Installation Procedures Nutec Bigsix Roofing sheets properly laid and fixed in accordance with recommendations will provide many years of trouble-free protection from the elements. Failure to follow these
More information900 SERIES PANEL SHEET INDEX STAGGERED ENDLAP STAGGERED MALE LEG AT ENDLAP CONTINUOUS FEMALE ENDLAP INSTALLATION SEQUENCE CI-WR
900 SERIES PANEL CI-DS-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-EL-01-900 CI-EL-02-900 CI-EL-03-900 CI-EL-04-900 CI-EL-05-900 CI-EL-06-900 CI-EL-07-900 CI-EL-08-900 CI-RD-01-900 CI-RD-02-900 CI-RD-03-900 CI-EV-01-900
More informationThe Roofing Store TRS 9 35MM 78MM 150MM 78MM PRODUCT TECHNICAL DATA
TRS 9 35MM 78MM 150MM 78MM THICKNESS END SPAN INTERNAL SPAN MINIMUM PITCH 0.55MM 2.30M 3.20M 3 DESCRIPTION TRS 9 profile is designed for commercial and industrial roofing. The profile is suitable for low
More informationSHED PACK. Sheds are commonly constructed using portal frames.
SHED PACK Sheds are commonly constructed using portal frames. This pack relates to purchasing portal frame purlin bracket sets. Ruest our free generic engineered and certified shed plans. SHED PACK Step
More informationrange of colours in COLORBOND factory pre-painted steel and in unpainted
SPANDEK LYSAGHT SPANDEK Trapezoidal steel cladding Roofing & Walling Solutions LYSAGHT SPANDEK is a contemporarylooking, trapezoidal profile which is ideal where a stronger, bolder, more modern corrugated
More informationHOLLOW CORRUGATED SHEETS
P R O D U C T C A T A L O G U E HOLLOW CORRUGATED SHEETS www.tuflite.com Bangalore (Head Office) #240/1, Ganesh Krupa, 18th Cross, Sadashivanagar, Bangalore- 560 080, India P: +91 80 4252 5252 F: +91 80
More informationSheet Steel Facts. Most common head design for self-drilling, self-tapping screws.
Sheet Steel Facts Fastener Guide for Sheet Steel Building Products August, 2003 Fastener Materials Fasteners are manufactured from several materials and coatings. For the purpose of this fact sheet, the
More informationUsing Lysaght Roofing & Walling edition
Using Lysaght Roofing & Walling Roofing & Walling Solutions Rainwater Solutions Structural Solutions Fencing Solutions Home Improvements House Framing Solutions 2003 edition Customer Support Using LYSAGHT
More informationINSTALLATION GIUDE.
INSTALLATION GIUDE INTRODUCTION The instructions and drawings included here are intended only as a guide for the installation of ECO Roofing Systems Spanish and Modern profiles. The materials and methods
More informationConstruction details: Master-C type profiles and joints:
Construction details: Master-C type profiles and joints: Master-C 3g 32 mm. (1 1/4 ) 1000 mm. (39 3/8 ) outer face inner face 10.5 fixing details: sealing washers shall be installed through a 2-3/8 x 1-9/16
More information4 LYSAGHT Product Catalogue Disclaimer, warranties and limitation of liability
isclaimer, warranties and limitation of liability This publication is intended to be an aid for all trades and professionals involved with specifying and installing products and not to be a substitute
More informationMetroll. Purlins & Girts. C Section Purlins. C Section Purlins are manufactured from Galvaspan steel and are roll formed into C Section.
C Section Purlins C Section Purlins are manufactured from Galvaspan steel and are roll formed into C Section. Metroll C Section Purlins are recommended for simple, non-continuous span construction. Structural
More informationDUTCH GABLE FREESTANDING CARPORT
DUTCH GABLE FREESTANDING CARPORT STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your complete guide to building a FREESTANDING Outback DUTCH GABLE CARPORT BEFORE YOU START Carefully read these instructions. If
More informationProduced by the Construction Resource & Development Centre. Reprinted by the Construction Industry Council
Produced by the Construction Resource & Development Centre. Reprinted by the Construction Industry Council Over the past 15 years the frequency and intensity of hurricanes impacting Jamaica has increased
More informationTABLE OF CONTENTS A. PBR
TABLE OF CONTENTS A. PBR Panel 1. PBR Panel Architect/Engineer Information....................................... 2 2. PBR Panel UL 90 Requirements............................................... 3 3. PBR
More informationWith Pitch Collector Frame
With Pitch Collector Frame INSTALLATION INSTRUCTIONS FOR SOLAR WATER HEATER SYSTEMS This frame must be installed by an authorised person. Please leave this guide with the householder. SOLAHART INDUSTRIES
More informationInsulated Corrugated. Patio Installation Guide. SupaCore Insulation Superior Thermal Performance. Colorbond Steel Roof & Ceiling. InsulRoof roof panel
Using the slot on the Turn-up/Turn-down tool, place the tool into the steel sheeting InsulRoof roof panel Rivet fixing through flashing Insulated Corrugated Roof pan turned down - gutter en 100mm Gutter
More informationInstallation Manual. Last Updated 4 February, Postal PO Box 932 Bayswater VIC
Installation Manual Last Updated 4 February, 2013 Part 1: Provided Material The Panel Expandable Foam Sealing Strip Barge Capping Z-Fascia Structural Screws Timber: 3/8 head size Metal: 5/16 head size
More informationThompson Architectural TM-RIB PANEL ACCESSORY DETAIL GUIDE
TM-RIB PANEL ACCESSORY DETAIL GUIDE FL11101.1 FL11101.2 TA125 (UL580 Class 90) Certified Thompson Architectural Metal Roofing is proud to be a partner of the Energy Star Roof Products Program SINGLE SOURCE
More informationHugger Installation. Roof Hugger, LLC P: P.O. Box 1027 F: Odessa, FL
RECEIVING MATERIALS: ROOF HUGGERS are typically placed on wood pallets 3-5 wide and approximately 10 long weighing up to 5,000 lbs. ROOF HUGGERS are shipped via closed van for LTL less than truckload quantities
More information+91-8048763366 Steel World http://www.steelworldindia.com/ We are engaged as manufacturer, supplier & exporter of poly carbonate sheet, imported fasteners brand name corroshield, purlin, roof vent, silicon
More informationThermoSpan EPS. Metalcraft COMMERCIAL ROOFING CREPS. Insulated Panel Systems DETAIL LIST
ThermoSpan EPS DETAIL LIST 00 / 15 COVER SHEET 01 / 15 RIDGE DETAIL 02 / 15 HEAD FLASHING DETAIL 03 / 15 EAVES GUTTER DETAIL 04 / 15 INSULATED GUTTER 05 / 15 INSULATED BOX GUTTER 06 / 15 BARGE CAPPING
More informationTable of Contents. Fasteners... 4 Venting Preparation Installation with Battens - DECRA Tile & DECRA Shake 1
Table of Contents DECRA Tile & Shake Roof Overview... 2 Introduction... 3 Safety... 3 Tools.... 3 Estimating Sheets... 4 Codes & Requirements... 4 Roof Slope... 4 Underlayment... 4 Deck Preparation....
More informationNutec Bigsix Roofing Accessories
Nutec Bigsix Roofing Accessories Nutec Bigsix Close Fitting Adjustable Ridge Capping (Grey) Adjustable for 0º - 0º pitches 70-000 87 mm 70-00 87 mm Nutec Bigsix Close Fitting Adjustable Ridge Capping (Terracotta)
More informationHOW TO Fix Onduline Corrugated Bitumen Sheets
HOW TO Fix Onduline Corrugated Bitumen Sheets BBA BRITISH BOARD OF AGREMENT CERTIFICATE NO. 87 / 1823 W ROOFING PLAN IT Roofing components: Ridge Roof decking Apex Verge Barge board Purlins / battens Rafters
More informationextend your outdoor lifestyle
extend your outdoor lifestyle www.laserlite.com.au Up to 50% better heat reduction than standard sheet # only Laserlite has the technology Laserlite is the only polycarbonate sheet product in Australia
More informationGLOSSARY OF TERMS SECTION 8
GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the
More informationROOFING & WALLING. for design and installation professionals Edition. installation manual. Roofing & Walling
ROOFING & WALLING Installation Manual for design and installation professionals 2014-2015 Edition 1 installation manual installation manual 2 Introduction & General Notes 4 Contents PART B: INSTALLATION
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationTRADITIONAL GABLE ATTACHED PATIO AND CARPORT. Your complete guide to building an ATTACHED Outback TRADITIONAL GABLE PATIO or CARPORT
TRADITIONAL GABLE ATTACHED PATIO AND CARPORT STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your complete guide to building an ATTACHED Outback TRADITIONAL GABLE PATIO or CARPORT BEFORE YOU START Carefully read
More informationTOPSPAN 22 / 40 LYSAGHT TOPSPAN 22 / 40. Steel roof and ceiling battens for non cyclonic applications
TOPSPAN 22 / 40 LYSAGHT TOPSPAN 22 / 40 Steel roof and ceiling battens for non cyclonic applications Our TOPSPAN 22 ceiling batten and TOPSPAN 40 roof battens are the economical alternative to timber battens.
More informationcalculated with factor of safety of 2.5 for bending stress, 3.0 for shear stresses and deflection limitation of L/180.
Metl-Span CF-42 Light Mesa Wall Panels 26 Ga. Exterior / 26 Ga. Interior Facings Allowable Connection Load 1,7,8,9,10 (psf) for Two or More Equal Spans Panel Type 2 Design Criteria 3,4,5,6 Support Span
More informationFLORIDA PRODUCT APPROVAL GULFRIBTM FLORIDA PRODUCT APPROVAL NO R3. Product Evaluation Report GULF COAST SUPPLY & MANUFACTURING, LLC.
Product Evaluation Report GULF COAST SUPPLY & MANUFACTURING, LLC. 26 Ga. GulfRib Roof Panel over over 15/32 Plywood Florida Product Approval #11651.21 R3 Florida Building Code 2017 Per Rule 61G20-3 Method:
More informationFLORIDA PRODUCT APPROVAL 5VCRIMP FLORIDA PRODUCT APPROVAL NO R2. Product Evaluation Report GULF COAST SUPPLY & MANUFACTURING, LLC.
26 GUAGE PANEL OVER 1X4 WOOD PURLINS OVER 15/32 PLYWOOD NO. 11651.14 R2 Product Evaluation Report GULF COAST SUPPLY & MANUFACTURING, LLC. 26 Ga. 5V Crimp Roof Panel over over 15/32 Plywood Florida Product
More informationChiko Flat Pitched roof installation roof installation Guide Gui
Mounting Systems Tilt Kit Installation Guide Table of Contents Part I. Preparing.. 2-6 Part II. Feature of the Rail and the Module 6-8 Part III. Planning the array laylout... 9 Part IV. Installation instruction.
More informationRoofing & Walling. Installation Manual
Roofing & Walling Installation Manual 2012-2013 Roofing and Walling Manual Date of Issue February, 2012 This Guide is the 2012-13 edition of the LYSAGHT Roofing & Walling Manual, issued on February, 2012.
More informationTRIM-KLIP INNOVATIVE END/EXPANSION JOINT SOLUTION FOR LYSAGHT TRIMDEK
TRIM-KLIP INNOVATIVE END/EXPANSION JOINT SOLUTION FOR LYSAGHT TRIMDEK LYSAGHT TRIM-KLIP The new TRIM-KLIP system provides installers with a quick and easy end joint/expansion joint solution between overlapping
More informationUL Construction No. 254
UL Construction No. Wind-Uplift - Class 90 (See Item No. ) / Fire Not Investigated Metal Roof Deck Panels* Snap-Clad No. MSG or No. MSG min. thickness coated steel panels. Panels in. wide max., 0 in. wide
More informationFastener Design. Fastener Materials. Coated Corrosion-Resistant Fasteners. Metal Alloy Capped Fasteners
Threaded fasteners for roofing and siding systems are available in a wide range of materials, designs, and coatings. When specifying your fastener, be sure to choose one that has a performance life equaling
More informationA Shell construction
A Shell construction A 4/2012 Content 1 BASE AND WALL ANCHORING 1.1 Base with mortar bed 1.2 Base with sill plate 1.3 Base with raised sill plate 1.4 Concrete base (mortar bed) 1.5 Concrete base (sill
More informationStructural Design Documentation
Gamcorp (Melbourne) Pty Ltd Consulting Structural & Civil Engineers A.C.N 141 076 904 A.B.N 73 015 060 240 www.gamcorp.com.au melbourne@gamcorp.com.au 1/19 Anthony Drive, Mount Waverley VIC 3149. Tel:
More informationWhen you need a clearspan of up to 6 metres of longrun steel you need...
YEARS OF BUILDING TECHNOLOGY When you need a clearspan of up to 6 metres of longrun steel you need... The proven longrun roofing and cladding system STYLISH Bold profile. High rib (75mm). Internal partitioning.
More informationMetal Roof Installation Manual. Chapter 2: Metal Roofing: A Family of Products / History of Metal Roofing
Metal Roof Installation Manual Chapter 2: Metal Roofing: A Family of Products / History of Metal Roofing Chapter 2: Metal Roofing: A Family of Products / History of Metal Roofing Chapter Contents 2. Metal
More informationGlobal Roofing Solutions Klip-Lok 700
GRS Klip-Lok 700 Global Roofing Solutions Klip-Lok 700 www.globalroofs.co.za marketing@globalroofs.co.za GRS Klip-Lok 700 GRS Klip-Lok 700 09/18 Typical Specification Materials The roofing shall be Klip-Lok
More informationPRICE LIST - 6th February 2017
W: www.cladco.co.uk E: info@cladco.co.uk T: 01837 659901 F: 01837 659902 Cladco Profiles North Road Industrial Estate, North Road, Okehampton, Devon, EX20 1BQ. PRICE LIST - 6th February 2017 Colour coated
More informationMULTISPAN GABLE WITH HIP END ATTACHED PATIO
MULTISPAN GABLE WITH HIP END ATTACHED PATIO STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your supplementary guide to building an ATTACHED MULTISPAN GABLE VERANDAH or PATIO WITH HIP END This set of instructions
More informationPINEHAVEN SHEDS Assembly Instructions FOR LEAN-TO SHEDS
PINEHAVEN SHEDS Assembly Instructions FOR LEAN-TO SHEDS GARDEN PRODUCTS www.pinehavensheds.co.nz 5/16 hex drive bit, By asking about our products at your nearest DIY or gardening store www.pinehavensheds.co.nz
More informationLONGLINE 305 WA design and installation guide western australia
LONGLINE 305 WA design and installation guide western australia 1 longline 305 WA Lysaght Longline 305 WA Steel roof cladding with long, clean lines longline 305 WA is a concealed fixed roof cladding with
More informationINSTALLATION GUIDE. Outback. Flat Attached BEFORE YOU START ADDITIONAL MATERIALS TOOLS REQUIRED. VERAnDAHS PATIOS CARPORTS
INSTALLATION GUIDE Outback VERAnDAHS PATIOS CARPORTS Flat Attached BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback
More informationROOFING & WALLING. for design and installation professionals. installation manual. Roofing & Walling
ROOFING & WALLING Installation Manual for design and installation professionals 1 2 Introduction & General Notes 4 Contents PART B: INSTALLATION 30 PART A: DESIGN 6 Design preliminaries 6 2.1 Product selection
More informationALUMINIUM SOLAR MOUNTING SYSTEM. Components catalogue FOR ALL TYPES OF ROOFS AND SITES
Components catalogue MOUNTING RAILS CARRIERS FOR RAILS FASTENERS BOLTS AND NUTS CLIPS FLAT ROOFS STRUCTURES FREE FIELD SYSTEMS COMPLEX ROOFS SYSTEMS ALUMINIUM SOLAR MOUNTING SYSTEM FOR ALL TYPES OF ROOFS
More informationOUTBACK FLAT ATTACHED VERANDAH PATIO CARPORT - INSTALLATION GUIDE BEFORE YOU START TOOLS REQUIRED ADDITIONAL MATERIALS
BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback Flat Verandah. It is the builder s responsibility to ensure any
More informationVENTED GABLE DETAIL ROOF PANEL GABLE FLASHING 24" C/C MAX. BUTYL SEALANT TAPE ROOF PURLIN FLASH AB-1, AB-2, AB-3, OR AB-4
ROOF PANEL GABLE FLASHING FASTENER @ 24" C/C MAX. ROOF PURLIN BUTYL SEALANT TAPE FLASH AB-1, AB-2, AB-3, OR AB-4 FASTENER @ EVERY MAJOR RIB OR 12" C/C MAX. F-J TRIM FABRAL ALUMINUM SOFFIT FASTENER 24"
More informationFIXING GUIDE. Designed for Garages & Sheds, Houses, DIY, Flat Roofs, Industrial & Agricultural Buildings etc. IS THE LONG TERM ROOFING SOLUTION
FIXING GUIDE Designed for Garages & Sheds, Houses, DIY, Flat Roofs, Industrial & Agricultural Buildings etc. IS THE LONG TERM ROOFING SOLUTION Permaroof Permaroof Permaroof Profile Roofing Manufacturers
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will
More informationCOMPATIBILITY OF FASTENERS
COMPATIBILITY OF FASTENERS TECHNICAL BULLETIN Vol. 4, No. 2 NOVEMBER 2011 This bulletin applies to conditions where fasteners are not provided by Metl-Span. Profiled metal roof or wall panels rely upon
More informationBlokes Shed INSTALLATION INSTRUCTIONS Custom Design & Build. Nationwide Delivery
Blokes Shed 10 Year Guarantee On Sanders workmanship Made in NZ Using NZ timber supplies 40+ Years Experience In business since 1975 Professional Install Available NZ wide Nationwide Delivery Available
More informationFive Star Panel Installation Instructions
Five Star Panel Installation Instructions How to Store Five Star Panels You will need to store FIVE STAR PANELS in dry place to prevent staining, deterioration and possibly void all warranties. Stand the
More informationmanthorpe Roll-Out Dry Fix Ridge System building products Fixing Instructions MBP 8265e
manthorpe building products Roll-Out Dry Fix Ridge System Fixing Instructions MBP 8265e Ridge Details Fig A. Assembly View of Dry Ridge Detail s/s screw clamping plate rubber washer foam spacer ridge tile
More informationDETAIL MANUAL. Metal Roofing Wholesalers. Classic Rib Roofing Panels
Metal Roofing Wholesalers Classic Rib Roofing Panels DETAIL MANUAL 1178 Topside Rd Louisville, TN 37777 The Classic Rib Roofing Panel Figure 1 House With Classic Rib Metal Roofing Installed Classic Rib
More information4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS
4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS Recommended Tools: Before You Begin: Saftey Glasses, Tape Measure, Carpenters Level, Framing Square, Hex Head Nut Drivers, Chalk Line, Elec.
More informationDETAIL MANUAL for Standing Seam / Image II
DETAIL MANUAL for Standing Seam / Image II Best Buy Metals Toll Free 1-800-728-4010 / Phone 423-479-6382 / Fax 423-728-3066 www.bestbuymetals.com Best Buy Metals Standing Seam Roofing Panels Fig. 2 Standing
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationIntex Engineered Pergola System Installation Instructions. NOTE: See Appendix for Foundation Requirements
Intex Engineered Pergola System Installation Instructions NOTE: See Appendix for Foundation Requirements Pergola Installation, Freestanding (If pergola will be attached-to-structure, skip to page 3) 1.
More informationAS TESTED TBA FIREFLY TBA FIREFLY BAL-FZ BUSHFIRE ROOF SYSTEM INSTALLATION GUIDE EASY TO INSTALL EASY TO CARRY EASY TO TRANSPORT
AS1530.8.2 TESTED BAL-FZ BUSHFIRE ROOF SYSTEM INSTALLATION GUIDE EASY TO TRANSPORT EASY TO INSTALL EASY TO CARRY Completely wrap the whole roof frame, including valleys, hips, ridges, fascia, eave, bargeboard
More informationNEVADA ASSEMBLY INSTRUCTIONS
NEVADA ASSEMBLY INSTRUCTIONS BASE SIZE: 2.700m x 1.500m NEVADA Tools Required: Battery Drill Riveter Hammer Tape Measure Ladder Skillsaw Level Screwdriver - Flat 3/8 Hex Drive bit 8mm Hex Drive bit Drill
More informationDesign Guide Pryda Connectors for Steel Framing
Pryda Connectors for Steel Framing Copyright: (c) Pryda Australia A Division of ITW Australia November 2012 November 2012 Design Guide Pryda Connectors for Steel Framing INDEX General Notes General information
More informationBest Buy Metals Toll Free / Phone / Fax
DETAIL MANUAL for Vertical Seam Best Buy Metals Toll Free 1-800-728-4010 / Phone 423-479-6382 / Fax 423-728-3066 www.bestbuymetals.com Vertical Seam Roofing Panels Fig. 2 Vertical Seam Has 1-3/4" high
More informationMulti-wall Polycarbonate Installation Instructions
Multi-wall Polycarbonate Installation Instructions Multi-wall polycarbonate sheet can be used on both gable and arched style greenhouses. These easy to install panels can be attached directly to the greenhouse
More informationSecuAnch Roof Anchor System
Height Safety Products Email: marketing@fallprotec.com SecuAnch Roof Anchor System 1 Presentation The SecuAnch lifeline is designed to be permanently installed on buildings and other structures where maintenance
More information1 P a g e THIS IS A GENERIC MANUAL AND MAY NOT BE INDICATIVE OF YOUR CONSTRUCTION.
1 P a g e INDEX SECTION DESCRIPTION PAGE 1 TOOLS REQUIRED 3 2 GENERAL PARTS IDENTIFICATION.... 4 2.1 Structural Members 4 2.2 Brackets.. 4 2.3 Fasteners and Bolts 5 2.4 Roof and Wall Cladding.. 5 2.5 Gutters
More informationHANDI-MATE SHED BEFORE YOU START INSTALL GUIDE HINGED DOOR HANDI-MATE INSTALLATION GUIDE PRIOR TO INSTALLATION
HANDI-MATE SHED HINGED DOOR HANDI-MATE INSTALLATION GUIDE INSTALL GUIDE BEFORE YOU START PRIOR TO INSTALLATION It is important that you contact your local government authority to determine if building
More informationMetal Roof Installation Manual. Chapter 14: Fasteners
Metal Roof Installation Manual Chapter 14: Fasteners Chapter 14: Fasteners Chapter Contents 14. Introduction... 14-1 14.1 Fastener Parts and Installation... 14-1 14.1.1 Points... 14-1 14.1.2 Heads... 14-1
More information+91-8048600448 Advance Roof & Building System http://www.advanceroof.co.in/ We are listed among the leading manufacturer, trader and supplier of a commendable assortment of Colour Coated & Insulated Sheets.
More informationFEET, WHEELS, FLOOR FASTENINGS, SUPPORTS
SYSTEM COMPONENTS FEET, WHEELS, FLOOR FASTENINGS, SUPPORTS s t r oppu S, s gn i n e t s af r oo l F, s l eehw, t e ef FEET, WHEELS, FLOOR FASTENINGS, SUPPORTS 136 MINITEC PROFILE SYSTEM BASE AND TRANSPORT
More informationGlobal Roofing Solutions Klip-Tite
GRS Klip-Tite Global Roofing Solutions Klip-Tite www.globalroofs.co.za marketing@globalroofs.co.za GRS Klip-Tite GRS Klip-Tite 09/18 Typical Specification Materials The roofing shall be Klip-Tite profile,
More informationIDAHO ASSEMBLY INSTRUCTIONS. BASE SIZE: 1.800m x 1.200m
IDAHO ASSEMBLY INSTRUCTIONS BASE SIZE: 1.800m x 1.200m IDAHO Tools Required: Battery Drill Riveter Hammer Tape Measure Ladder Skillsaw Level Square Drive Bit No.2 3/8 Hex Drive Bit 8mm Hex Drive Bit Drill
More informationHILAND TRAY FORM AND FUNCTION MATERIAL SPECIFICATIONS DESIGN GUIDE ROOFING I WALLING
HILAND TRAY ROOFING I WALLING DESIGN GUIDE FORM AND FUNCTION Hiland Tray is a modern 455mm wide tray roofing and walling system, roll formed onsite with a mobile roll forming facility in long single lengths
More informationRoll-Fix Kit The complete dry hip kit RFIG
H I P Roll-Fix Kit The complete dry hip kit RFIG.045-0906-1 Roll-Fix is a quick and simple dry-fix roofing kit for hips. l Quick and easy to install no special tools required l Universal application fits
More informationStratco Sanctuary INSTALLATION BEFORE YOU START TOOLS REQUIRED GUIDE
INSTALLATION GUIDE Stratco Sanctuary Verandahs, Patios and Carports BEFORE YOU START It is important to check with your Local Government Authority prior to the installation of your new Stratco Sanctuary
More informationREPORT ON BUILDING DAMAGE FROM DOWNBURSTS, WESTERN AUSTRALIA, 25 FEBRUARY 2018
REPORT ON BUILDING DAMAGE FROM DOWNBURSTS, WESTERN AUSTRALIA, 25 FEBRUARY 2018 1. INTRODUCTION At around 10:30 am Western Standard Time (WST) on Sunday 25 th February 2018 a thunderstorm that had generated
More informationA REVOLUTION IN AUSTRALIAN ROOFING.
A REVOLUTION IN AUSTRALIAN ROOFING. The roofing industry in Australia For too many years architects, builders and roofers have had limited choices in roofing and material options. Until now. In an industry
More information900 SERIES WALL PANELS
CI-DS-01-900 CI-PP-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-PJ-03-900 CI-BS-01-900 CI-BS-02-900 CI-BS-03-900 CI-BS-04-900 CI-BS-05-900 CI-OC-01-900 CI-OC-02-900 CI-IC-01-900 CI-FO-01-900 CI-FO-02-900 CI-FO-03-900
More informationInstallation Guide. for Ampelite Industrial Sheeting STD. Premium Industrial Sheeting. Industrial Grade Fibreglass. Industrial Grade Fibreglass
Installation Guide for Ampelite Industrial Sheeting Premium Industrial Sheeting STD Industrial Grade Fibreglass Industrial Grade Fibreglass Industrial Grade Fibreglass AS/NZS ISO 9002 Licence QEC 4787
More informationMANUAL MOUNTING SYSTEM FOR BITUMEN / EPDM
MANUAL MOUNTING SYSTEM FOR BITUMEN / EPDM EN mounting system for insulated pitched roof Bitumen / EPDM for solar panels landscape setup ESDEC BV 2015 TABLE OF CONTENT 1. Introduction 1 2. General installation
More informationInstallation Manual FLUSH MOUNT - Shingle, Slate,etc. Questions? Call Us! +1 (800)
www.trasnowandsun.com S Installation Manual FLUSH MOUNT - Shingle, Slate,etc. At TRA Snow and Sun we engineer and layout each project upon request free of charge. Just give us the project details and we
More informationCode-Compliant Planning and Installation Complying with AS/NZS1170.2:2011 ADMT
PV-ezRack SolarRoof Code-Compliant Planning and Installation Complying with AS/NZS1170.2:2011 ADMT 2-2012 CONTENT 1. Introduction 2 2. Planning. 3 3. Component List 9 4. Array planning.. 10 5. Step by
More informationStoring, Handling, and Cutting Steel Panels
Storing, Handling, and Cutting Steel s Storing Specifically check your quantities, colors, and lengths All materials should be used as soon as possible Steel bundles should be stored indoors with enough
More information