Finesse Profiles. Nailstrip

Size: px

Start display at page:

Download "Finesse Profiles. Nailstrip"

Lynn Phelps
5 years ago
Views:

1 Installation Details Profile and Lap Detail 265/465 38mm NAILSTRIP *other widths available CD GRADE PLYWOOD 19mm STRUCTURE SILICONE * MIN 20mm VENTILATION GAP * WHEN ROOF PITCH IS UNDER 7.5 OR TOTAL COMBINED SHEET LENGTH IS OVER 5 METRES. #10-12 X 25mm WAFER HEAD WOOD 450mm CTS Figure NS ID 004

2 Installation Details: Low Eave/Gutter or Aluminium CD GRADE PLYWOOD 19mm SCREWS TO EDGE OF SHEET NAILSTRIP PANEL RIB CLOSURE PAN TURNED DOWN TO DRIP INTO GUTTER CUT BACK RIB ON ANGLE. EDGE FOLDED TO CLOSE. POP RIVET AND SEAL WITH SILICONE. POP RIVET TURN DOWN PAN TO FORM DRIP INTO GUTTER NAILSTRIP SCREWS TO EDGE OF SHEET FASTENERS #10-12 X 25mm WAFER HEAD WOOD SCREW W/ #2 100mm CTS. MIN 20mm VENTILATION GAP EAVES GUTTER EXT GUTTER BRACKET Figure NS ID 005

3 NAILSTRIP CUT BACK RIB ON ANGLE. EDGE FOLDED TO CLOSE. POP RIVET AND SILICONE SEAL PAN TURNED DOWN - 25mm POLE PLATE FLASHING #10-12 X 25mm WAFER HEAD WOOD SCREW W/ #2 PHILLIPS 100mm CTS. CD GRADE PLYWOOD 19mm WITH ROUTED REBATE MIN 20mm VENTILATION GAP Figure NS ID 006 FASTENER FIX THROUGH TO PLY SUBSTRATE AT MIN 900 C/C 175mm 25mm NOTCHED OVER RIBS BARGE CAPPING NAILSTRIP CD GRADE PLYWOOD 19mm LOW PROFILE FASTENER (BY INSTALLER) FOLD UP END OF SHEET SEE SHEET - TYPICAL STOP END Figure NS ID 007

4 Installation Details: Typical Ridge CD GRADE PLYWOOD 19mm HEX HEAD FIXING FOLD UP END OF SHEET SEE SHEET - TYPICAL STOP END 150 mm 25mm VENTILATION GAP ONE-PIECE RIDGE CAPPING FIX THROUGH TO SUBSTRATE AT MIN 900 C/C TVP C/BOND NAILSTRIP Figure NS ID 008

5 Installation Details: Typical Barge BARGE CD GRADE PLYWOOD 19mm MINIMUM 20mm VENTILATION 40mm BATTEN BARGE FLASHING BARGE Figure NS ID 009 BARGE FLASHING BARGE BARGE CD GRADE PLYWOOD 19mm MINIMUM 20mm VENTILATION Figure NS ID 010

6 Installation Details: One slope ridge TURN UP END PANEL SEE SHEET 2-2 RIDGE CAPPING FASTENER NAILSTRIP FASTENER MINIMUM 20mm VENTILATION GAP Figure NS ID 011

7 Installation Details: Typical Apron Flashing to Wall FOLDED APRON FLASHING WALL STRUCTURE CHASE INTO WALL NEUTRAL SEALANT FOLDED FLASHING 10mm MIN 10mm MIN 40mm BATTEN IF OVER 240mm 150mm MIN CD GRADE PLYWOOD 19mm SCREW Figure NS ID 012

8 Installation Details: Typical Valley Over 7.5 FASTENERS #10-12 X 25mm WAFER HEAD WOOD SCREW W/ #2 100mm CTS. CD GRADE PLYWOOD 19mm WITH ROUTED REBATE C/BOND VALLEY RIB CLOSURE TURNED DOWN MINIMUM 20mm VENTILATION GAP NAILSTRIP PANEL RETURNED EDGE 25mm REBATE PLY Figure NS ID 013 REBATE UNDER VALLEY RIBS VALLEY CENTRE OF VALLEY GUTTER TURNDOWN PLAN VIEW Figure NS ID 014

9 Installation Details: Typical Valley Over 7.5 (cont.) CUT BACK RIB ON ANGLE. EDGE FOLDED TO CLOSE. Figure NS ID 015 Installation Details: Typical Valley Under 7.5 PAN TURNED DOWN VALLEY 25mm BYCELL COMPRESSED STRIP NAILSTRIP PANEL RIB CLOSURE CD GRADE PLYWOOD 19mm WITH ROUTED REBATE MINIMUM 20mm VENTILATION GAP Figure NS ID 016

10 Installation Details: Typical Valley Under 7.5 (cont.) GUTTER RIBS VALLEY CENTRE OF VALLEY TURNDOWN Figure NS ID 017 PLAN VIEW Figure NS ID 018

11 Installation Details: Typical Ventilation CUT BACK RIB ON ANGLE. EDGE FOLDED TO CLOSE. NAILSTRIP CD GRADE PLYWOOD 19mm VENTILATION STEELWORK BY OTHERS PURLINS BY OTHERS Figure NS ID 019

12 Installation Details: Typical Panel Turndown 1. Panels requiring field hemmed ends should be fabricated 25mm longer than the finished panel length. Valley conditions must be field cut to the appropriate angle. 2. Cut back panel joints 25mm. 3. Place protruding pan into the panel hemming tool. The front edge of the tool must rest against the notched joint legs on both sides. 4. While maintaining pressure against the panel joints, rotate the hemming tool as close to 90 as possible. AL PANEL TURN-DOWN 25 CUT RIBS BACK 25mm PANEL HEMMING TOOL Figure NS ID 020

13 Installation Details: Typical Stop End 1. Place pan into the panel stop end tool. The front edge of the tool must rest between the ribs. 2. While maintaining pressure against the panel, rotate the stop end tool as close to 90 as possible. 3. Inspect completed bend. OP END STOP END DETAIL PANEL WITH STOP END PANEL STOPEND TOOL Figure NS ID 021

TYPICAL BARGE DETAIL - CROSS SECTION

TYPICAL BARGE DETAIL - CROSS SECTION SELECTED OWENS CORNING ASPHALT SHINGLES APPLY A BEAD OF BITUMASTIC ADHESIVE/SEALANT METAL BARGE DRIP EDGE FLASHING No15 RAG FELT ROOF UNDERLAY PLYWOOD ROOF FRAME BARGE BOARD SOFFIT LINING (IF APPLICABLE)