DIY Stevenson Screen Part 1
|
|
- Ira Victor McKinney
- 5 years ago
- Views:
Transcription
1 DIY Stevenson Screen Part 1 Getting The Stevenson Screen Legs Ready 4 inch 10 cm 8 inch 20 cm First Part Screw holes 6 inch 15. m 2nd Part Screw holes 16 inch 40 cm 12 inch 30 cm Each Timber is 34 mm X 34 mm or 3 cm Each leg should look like this Drill out 3 holes in Each Leg Each Timber is 34 mm x 34 mm or 3 cm Each Timber is 34 mm X 34 mm or 3 cm Now turn the timber leg once and now Drill 2 holes in each leg You need to drill out 20 holes in total, that's 5 holes on each leg. Drill Size is up to you in what Screws you use! I was using 4mm Drill. Now when you have drilled all those Holes, you now need counter sink them. This Part done. see FIG 1
2 DIY Stevenson Screen Part 2 Make Sure the Slats are Pointing Down!! Diagram Diagram Screw the get to first paniel You should have 1 of these You sould have 2 of these nd Right, the large panel screw two legs on it, now the 2 Smaller Panel Screw only one leg to it, but screw it to the right hand, see Diagram, Please Not Don't Screw any legs to 2nd Wide Panel s this will be Your Door so leave this alone. see FIG 2
3 DIY Stevenson Screen Part 3 Make Sure the Slats are Pointing Down!! Now Screw Panel to Panel. Place Panel on the Floor Flat, Now Put Panel onto the side where there is no leg fixed to it, now you should have L shape with 3 legs. See Diagram Diagram Screw the get to first panel D This is Your Door Diagram D Now do the same with the other two Panels now you should have 1 L shape. nd one panel on its own, remember Panel D is your Door, See Diagram D see FIG 3
4 DIY Stevenson Screen Part 4 Diagram G D This Panel Is Door Diagram H 24 inch 60 cm Door atch D This Panel Is Door Door Hinges Diagram I Diagram G Door hain Door Side View with Door open 18 45cm Now Screw Panel / to and then to Panel / now you should have a U box and it should stand up now See Diagram H, Now cut a piece of timber at 20 50cm there are used for Door Frame. Fix these to Panel and See Diagram I, I used small L rakes, to support these. Now at this point you can now added the Door hinges and the door rackets and the hain to hold the Door. See Diagram G, Now you can Fix the door.. see FIG 4
5 DIY Stevenson Screen Part 5 Top ottom Door atch Door Hinges Diagram K Diagram L Top ottom 27 inch 68 cm 4 inch 10.cm lock c lock lock 6 inch 15. cm lock D Diagram M 27 inch 68 cm see FIG 5
6 DIY Stevenson Screen Part 6 Finally Putting together Stevenson Screen Diagram M lock c 4 inch 10.cm lock lock 6 inch 15. cm lock D Diagram G Door hain Door Side View with Door open 18 45cm 27 inch 68 cm Right if you buy your Plywood 606mm X 1220mm 12mm, you will find that you can cut Top and bottom from one sheet, First We Deal with the Top ut the Top to size see diagram L, soon as you have done that Next cut 4 pieces off timber See diagram M, now place to Top on floor upside down, but remember the Front Point now Place lock onto the ottom Top, see diagram m, but make sure you Messer this right, because this is the only way you can Support the Root without Screwing it, I've done this for easy ccess.. So when you got it right the Top should Hang forward more then back, I have found fixing these block to the inside of the roof I used No more Nails, ecause the last thing we don't want any hole at the top Onto bottom, all you need to do is cut the four orner's See diagram L, now all you need to do is Slid the ottom on and nail it down, but for Extra Support I places 4 L bracket from bottom basic the to legs, this will support any heavy item inside. Last of all prime the Stevenson screen, when priming make sure you prime inside as well, then wait for it to dry 3-4 hours, soon as it dry Pain it, I used Whit Paint, but it has to be out door paint, the one I found better is exterior paint for wood gloss white. You might need 1 or 2 coats. Now you have finished stand back and mire at what you have built.. Hope you enjoy you project as much as I have done. Thank you see FIG 6
Media Console Table 38"
Copyright 2016 Shanty-2-Chic.com Media Console Table A sleek, modern take on a traditional concept; this console table is as stylish as it is functional and you'll have it done in a weekend. And versatile
More informationExtra Wide Designer Lockers Series Installation Instructions
Extra Wide Designer Lockers 20000 Series Thank you for selecting the 20000 Series Extra Wide Designer Lockers. We are confident that the quality and construction of the lockers will prove to be a good
More informationOutdoor Storage Locker
Easy To Build Outdoor Storage Locker A little shed that spells big relief for a crowded garage Complexity: Simple Cost: $100-$500 Assemble this easy-to-build storage locker for your outdoor tools. It's
More informationHorse Stables for American Girl or 18" Dolls [1]
[1] Submitted by Ana White [2] on Fri, 2012-12-21 13:27 [1] Additional Photos [3] Page 1 of 20 [4] [5] [6] [7] Please don't be mad at me for getting you this plan just days before Christmas. I promise
More informationDIY RUSTIC HALL TREE
DIY RUSTIC HALL TREE *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationFan Back Adirondack Chair Assembly Instructions How To Assemble Your Chair in 12 Easy Steps Parts List 5 9
Fan Back How To Assemble Your Chair in 12 Easy Steps Parts List 5 9 5 5 9 5 5 1 12 11 7 7 1 8 13 10 2 6 4 3 3 3 3 3 2 #1 (2) frame, left & right #2 (2) 20" legs, left & right #3 (6) 20" seat slats #4 (1)
More informationROOM FOLD SLIDING FOLDING INTERNAL DOORSET FITTING & FIXING GUIDELINES
EDITION 7 ROOM FOLD SLIDING FOLDING INTERNAL DOORSET IMPORTANT You can only assemble these door configurations by using the frame provided. Your warranty will be invalid if other alternatives are used.
More informationHarriet Chair with Modifications
Harriet Chair with Modifications This modification of the Harriet chair includes a slat back, padded seat, and is 2 inches wider than the original plan. The overall dimensions of the finished chair: 38
More informationADULT. Adirondack / Muskoka Chair Plans
ADULT Adirondack / Muskoka Chair Plans Materials List 3/4" x 9 1/2" (1.9cm x 24.1cm) redwood, cedar or pine boards. Six, 8' (2.44m) boards should make one chair depending on knots and layout. You can also
More informationFrench Door W/Cut-Out (Outside Mount L-Frame-Single Panel)
NORMAN SHUTTERS INSTALLATION INSTRUCTIONS French Door W/Cut-Out (Outside Mount L-Frame-Single Panel) Getting Started Recommended Tools: Nail Gun or Cordless Drill, Tape Measure, Torpedo Level, Box Knife,
More informationSecret Storage Book. Part Lists. The Book
Secret Storage Book Part Lists Wood Screws ( (Werbilt flat head phillips #4 x ⅜ in) Drills Screwdrivers Hinges (2 medium and 3 small) Corner braces (¾ inches) Paint or scrapbook paper Leather Thick cardboard
More informationJewelry Cabinet. Materials: 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide. 1-4' x 8' sheet - 3/4" plywood. wood glue get 1x4's)
1 Jewelry Cabinet Materials: 1-4' x 8' sheet - 3/4" plywood 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide wood glue get 1x4's) sand paper 1-1" x 6" x 8' board wood filler 1/2 sheet - 3/16"
More informationREGENCY TIMBER BUILDINGS
REGENCY TIMBER BUILDINGS TEL 01948 830460 UNIT 22 PENLEY IND EST, PENLEY.WREXHAM. LL13 0LQ 1 Garage fitting instructions Tools needed handsaw, hammer, Stanley knife with hook blade, tape measure, battery
More informationFarmhouse Vanity 24-¼ 21-½
opyright 2015 Shanty-2-hic.com I Farmhouse Vanity nspired by simpler days of the past, this vanity is built with sophisticated charm and character. ozy and freestanding, this base can be paired with any
More informationPRODUCT NAME DOUBLE CARPORT + SHED REFERENCE NUMBER 1
PRODUCT NAME REFERENCE NUMBER 1 DOUBLE CARPORT + SHED IMPORTANT (Read carefully before starting)! - The following instructions include both pictures (indicating every part by the digits see part list above)
More informationINSTALLATION GUIDE Locker With Top Shelf Transit Low Roof & Nissan NV Low Roof ( Aluminum )
INSTALLATION GUIDE 7115 Locker With Top Shelf Transit Low Roof & Nissan NV Low Roof ( Aluminum ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Locker w/ Top Shelf Assembly... 3-5 6-13 Phase
More informationPRODUCT NAME RENNES REFERENCE NUMBER 1
PRODUCT NAME REFERENCE NUMBER RENNES 1 IMPORTANT (Read carefully before starting)! - The following instructions include both pictures (indicating every part by the digits see part list above) and illustrations.
More informationBi-Pass And Bi-Fold Sliders
Bi-Passs and Bi-Fold Sliders Installation Guide Bi-Pass And Bi-Fold Sliders Tools required: Hand Drill Counter Sink Drill BitSet #8 Philips Screw Driver Measuring Tape Level What s Included: Panels with
More informationFOLDAWAY DOOR SECTION OPTION 6. Assembly Instructions. Folding Work Desk (adjustable shelves behind can be accessed when the desk is in use)
FOLDAWAY DOOR SECTION OPTION 6 Folding Work Desk (adjustable shelves behind can be accessed when the desk is in use) Assembly Instructions It is strongly recommended to have two persons present when assembling
More informationFilling nail holes in drywall before painting. Filling nail holes in drywall before painting.zip
Filling nail holes in drywall before painting Filling nail holes in drywall before painting.zip personalized home and spend some extra time before move-out fixing tiny nail Jan 5, 2016 try out a few of
More informationHow to Build A Porch Swing
How to Build A Porch Swing SUPPLIES USED Tape measure Drill 2.5" Wood Screws 1.5" Wood Screws 2" Finishing nails Hammer (or nail gun if you're lucky) Sand paper/ Electric sander Exterior paint Safety glasses
More informationHow to Build a Recessed Medicine Cabinet
How to Build a Recessed Medicine Cabinet See post for install info http://www.hertoolbelt.com/recessed-medicine-cabinet/ Materials 6 Inset Cabinet Door Hinges 3 Latches 1 sheet Beadboard or 1/4 plywood
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationPREHUNG DOOR SYSTEM INSTALLATION INSTRUCTIONS: FIBRECOMP COMBINATION UNITS
PREHUNG DOOR SYSTEM INSTALLATION INSTRUCTIONS: FIBRECOMP COMBINATION UNITS Read all instructions before starting. Calgary Toll Free: 1-866-664-7664 Saskatoon Toll Free: 1-800-667-6977 Winnipeg Toll Free:
More informationThe image above is intended to give you an idea of what the dovecote will look like when finished.
Thank you for buying my book, I hope it is useful and enjoyable in your quest to building your own dovecote. This book will give you step-by step instructions on how to build your own dovecote also included
More informationProject: Bistro Set Overview: This is a set of four stools and one
Project: Bistro Set Overview: This is a set of four stools and one table that create a complete bistro set. Works great both indoors and out. By removing only a couple screws the entire project comes apart
More informationNEXUS SERIES CABINETS
NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions
More informationProject: Smoker Overview: Smoking meat has been around for. Materials: 3/4 plywood, 7-48 of 1/2 dowel,
Project: Smoker Overview: Smoking meat has been around for hundreds of years. Now with this simple smoker one can bring back to life the ancient methods of preserving meats and adding the smoky flavor.
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationExtra Tall Bar Stool [1]
Extra Tall Bar Stool [1] Submitted by community-contr... [2] on Fri, 2011-01-28 10:57 [1] Summary: An extra tall bar stool with cross bracing for added support. CategoriesRoom: kitchen [3] Skill Level:
More informationINSTALL INSTRUCTIONS CONTENTS: INSIDE MOUNT PAGE 2-7 OUTSIDE MOUNT PAGE 8-12
INSTALL INSTRUCTIONS CONTENTS: INSIDE MOUNT PAGE 2-7 OUTSIDE MOUNT PAGE 8-12 HOW TO INSTALL INSIDE MOUNT SHUTTERS Your shutters are designed to be easy to install and maintain. Depending on the shutter
More informationAssembly instructions. 6x4. Model GH1354A. 6x6. Model GH1357A. 6x8. Model GH1360A. 6x10. Walk-in Greenhouse. Model GH1363A
ssembly instructions x Model GH x Model GH7 x8 Model GH0 x0 Model GH Walk-in Greenhouse Statement ear Customer! May we congratulate you on your new Greenhouse. We feel sure that by following the detailed
More informationThe easy way to an affordable kitchen
quality, affordable, pre-assembled The easy way to an affordable kitchen In association with All Insta-Cupboard carcass units are supplied pre-assembled to simplify installation Choose the colour of your
More informationFull Size Bed The Jocelyn
Full Size Bed The Jocelyn www.andrewharriswoodwork.com Page 1 of 14 Introduction This plan makes a bead frame for a full size mattress. Although a full size mattress should be standard size. Please make
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 1
Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue
More informationining Table Materials *Notes on Materials
D ining Table We looked around for the perfect table for the dining room. Some were too big, some too small, and most were just too expensive. So we built this one, and we are happy with the result. It
More information36" Wall Cabinet, Double Door - Momplex Vanilla Kitchen [1]
36" Wall Cabinet, Double Door - Momplex Vanilla Kitchen [1] Submitted by Ana White [2] on Fri, 2013-12-27 15:58 [1] Page 1 of 17 Additional Photos [3] [4] [5] DIY Friends! Hope you are still enjoying a
More informationPatrol Box Plans by David J. Yarusso Troop 609
Patrol Box Plans by David J. Yarusso Troop 609 Materials List: 1. One 4 x8 sheet of ½ thick cabinet grade (birch or oak) or AC plywood. If using AC grade, use the A grade surface on the outside for a clean
More informationFirehouse Manual. Tools Needed:
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH
More informationSustainably made in the United States. Doors Make the Difference. stilechoice.com
Sustainably made in the United States Doors Make the Difference stilechoice.com Just What You Want Let s cut to the chase: At IHS Door Company we do one thing, and we do it really well. We make MDF stile
More informationCopyrighted Material Page 1
Compare to: Pottery Barn Teen Storage Bed System Skill Level: Beginner Working with the rest of the components in the Storage Bed Collection, the Small Hutch fits on top of the Storage Headboard and will
More informationWhite Mirrored Cabinet With EXT Shelves
White Mirrored abinet With EXT Shelves 33/0325 60cm 16.5cm 5cm Issue 5-06/13/13 UTIO: please do not place metal containers on the shelves as this could mark the paint omponents - anels If you have damaged
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationINSTRUCTIONS FOR ASSEMBLY 2355mm x 3125mm Workshop
Manufacturer of Christie Glasshouses and Sheds INSTRUCTIONS FOR ASSEMBLY 2355mm x 3125mm Workshop 1 Thomas Burns Street, Dunedin Phone (03) 477 7909 www.allans.co.nz Congratulations on your purchase of
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: TOOLS: (2) 2x2x8 Ft. Boards Tape Measure (2) 1x4x8 Ft. Boards Pencil (4) 1x2x8 Ft. Boards Carpenter s Square (1) 4x4 Ft. Sheet of ¾-Inch Plywood Drill with 5/16-inch Drill Bit (1) 1 ½-inch Thick
More informationAssembly Instruction. 9,2 m² Grillkota
Assembly Instruction 9,2 m² Grillkota Dear customers, Thank you for purchasing our product. We recommend that you read these instructions before installation and make the necessary preparations for building.
More informationGambrel Barn with Overhang Manual
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH
More information(1) 2x4 Ft. Sheet of ¼-inch Plywood. 1 ¼-inch Wood Screws. 1 ¼-inch Brad Nails ¾-inch Brad Nails Wood Glue CUT LIST:
MATERIALS: (5) 1x3x8 Ft. Boards (3) 2x4x8 Ft. Boards (10) 1x4x8 Ft. Boards (1) 1x2x10 Ft. Board (1) 2x2x4 Ft. Board (2) 1x6x8 Ft. Boards (1) 4x8 Ft. Sheet of ¾-inch Plywood (1) 2x4 Ft. Sheet of ¼-inch
More informationS H E D A S S E M B L Y I N S T R U C T I O N S
T I T A N R A N G E S H E D A S S E M B L Y I N S T R U C T I O N S 6 X 4ft = 190 x 150 cm 6 X 6ft = 190 x 190 cm 6 X 8ft = 190 x 255 cm COMPONENT LIST Component illustrations are given as a visual guide
More informationWallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS
Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note
More informationCopyright 2010 Springbok Publishing All Rights Reserved- Page 1
Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this
More informationPlease keep for future reference. Dimensions (5') Length cm. Width - 160cm Height cm
Sheridan Ottoman bed Assembly Instructions hygena Please keep for future reference 25/942 /659 56/4268 56/9 /7268 57/499 40/422 57/202 8/8846 Dimensions (4') Length - 202.5cm Width - 0cm Height - 84.5cm
More informationBuilding Instructions
Building Instructions Tools Required Tape measure Straight edge Pencil/pen Jigsaw Table Saw Circular Saw Electric drill 1 Hole saw bit Saw horses/table Protractor Staple gun Caulk gun Paint brush Wrenches
More informationHow to fit an Internal Door
How to fit an Internal Door How to fit an Internal Door The following instructions are for installing a internal door only. If you have any queries please contact Cheshire Mouldings technical helpline
More informationWall-mounted folding desk.
Wall-mounted folding desk. Step-by-step project The wall-mounted folding desk: ideal for small rooms. Are big desks not doing it for you? We feel the same way. They take up a lot of space, especially in
More informationLOWLINE SINGLE FOLD DOWN WALL BEDS
ASSEMBLY INSTRUCTIONS LOWLINE SINGLE FOLD DOWN WALL BEDS Tools Required For Assembly No 2 & No 4 Phillips Head Screwdrivers No 2 Slot Head Screwdriver Hammer Electric Drill (Hammer Drill for Masonry) 6.5mm
More informationBUILDING A GOAL WALL DO IT YOURSELF! INSTRUCTIONS FOR A GOAL WALL
INSTRUCTIONS FOR A In just a few steps, we show you how to build your own goal wall and paint it perfectly. COMPILED BY 1 PREPARING Purchase the materials from the enclosed list. The DIY store should be
More informationINSTRUCTIONS FOR ASSEMBLY 2355mm x 4665mm Workshop
Manufacturer of Christie Glasshouses and Sheds INSTRUCTIONS FOR ASSEMBLY 2355mm x 4665mm Workshop 1 Thomas Burns Street, Dunedin Phone (03) 477 7909 www.allans.co.nz Congratulations on your purchase of
More informationBenchmark Storage or Media Tower [1]
[1] Submitted by Ana White [2] on Wed, 2011-10-05 13:03 Page 1 of 23 [1] Page 2 of 23 So excited to post a plan today! Been working long and late hours trying to get a roof on the Momplex, and have really
More informationSauna & Steam. Traditional Sauna Installation Instruction Manual
Traditional Sauna Installation Instruction Manual Oceanic Ltd, Pountney Street, Wolverhampton, WV2 4HX Phone: 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk Contents 1.Introduction................................................
More informationFlip Down Wall Art Desk [1]
[1] Submitted by Ana White [2] on Mon, 2011-09-19 15:07 [1] Additional Photos [3] Page 1 of 20 This one has been a looooong time in the making. I first came up with the ideas of a wall mounted desk last
More informationSeries 1500 Aluminum Door Canopy
Series 500 Aluminum Door Canopy with Sidewings It is our recommendation that you read instructions carefully prior to assembly and installation. Series 500 with Sidewings mounting bar (A) top trim (B)
More informationS H E D A S S E M B L Y I N S T R U C T I O N S
T I T A N R A N G E S H E D A S S E M B L Y I N S T R U C T I O N S 8 X 10 ft Approx = 2550 x 3140 cm COMPONENT LIST Component illustrations are given as a visual guide only and are not in proportion PART
More informationExploded View PAGE 2 OF 9
Argon 02 Exploded View PAGE 2 OF 9 Supplied Parts Underframe Underframe Insert Wall to Glass Hinge Door Handle Door Bottom Seal Hinge Seal Bubble Seal PAGE 3 OF 9 Important Information This shower screen/enclosure
More informationSimple Stackable Outdoor Chairs
posted by Ana White [1] These simple chairs stack! And match our Simple Modern Outdoor Collection. Build a few to match the tables, or just extra seating for outdoors. About ProjectInspired By: West Elm
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS MODEL RTA - 4985 Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference.
More informationSauna & Steam. Vision Sauna Manual Wall Hung Heater Version (Covers all models)
Vision Sauna Manual 14.7.18 Wall Hung Heater Version (Covers all models) Oceanic Ltd, Pountney Street, Wolverhampton, WV2 4HX Phone: 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk Table
More informationSECTION 2: INSTALLATION
SECTION 2: INSTALLATION 2.1 PEDESTAL ASSEMBLY The T4000 pedestal is designed to support 100% of the weight of the ATM. Installed properly, the wall should not carry any load. Below represents the assembled
More informationNORMAN SHUTTERS INSTALLATION INSTRUCTIONS. 4 Sided Z Frame. (Inside Mount - 2 panel) Getting Started
NORMAN SHUTTERS INSTALLATION INSTRUCTIONS 4 Sided Z Frame (Inside Mount - 2 panel) Getting Started Recommended Tools: Nail Gun or Drill, Tape Measure, Torpedo Level, Box Knife, 6 Philips head driver Make
More informationCabonyx Installation Manual
Cabonyx Installation Manual Content Deck-Nyx and Plan-Nyx Installation Page 1 Flooring Products Page 1 Accessories Page 1 Installation Tools Page 2 Preparing Sub-structure Page 2 Installation Page 4 Cautions
More informationv.4 Helpline SUMMERHOUSES introductory offer 50 % OFF Introducing Outdoor living from Alton
SUMMERHOUSES Helpline 0800 058 0005 v.4 50 % OFF introductory offer Introducing Outdoor living from Alton 2 SUMMERHOUSES A whole new concept for a Cedar Summerhouse... Since 1921, Alton has been at the
More informationSuggested Installation Guide for the Hovr Bracket System
Suggested Installation Guide for the Hovr Bracket System Important: Every wall is different in make and material. If you are not sure how to install the WALLNUT shelf, please get someone who can help you,
More informationASSEMBLY INSTRUCTIONS TALL CABINET - MODEL CS30
ASSEMLY INSTRUCTIONS TALL CAINET - MOEL CS30 To avoid SERIOUS INJURY or AMAGE to personal belongings: O NOT overload the cabinet or the shelves, maximum weight limit for feet or caster installation is
More informationBaby Grande with Crank, Housing, and Side Rails Installation Instructions
Baby Grande with Crank, Housing, and Side Rails Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil
More informationWALL UNIT. Assembly Guide Lift. 288 x x x x 800
Assembly uide 288 x 600 288 x 800 360 x 600 360 x 800 or Internal Use: I.WR.INS.032_WKIN00121_WALL_600_800_Lift_Rev2.indd Assembly uide EORE YOU START INSTALLATION SHOULD E PERORMED Y A OMPETENT PERSON
More informationIndustrial Cart. Materials. With High Style Restyle
1 Industrial Cart With High Style Restyle Materials 1 sheet 3/4" plywood 1-1" x 2" x 8' board 2-1" x 3" x 8' board 1-2" x 8" x 10' board 1-2" x 6" x 8' board 3-1/4" x 2 1/2" x 4' poplar hobby boards, or
More informationkiva design kiva design GARDEN TOWNS Bill's Water Tower
GREN TOWNS Scaled and easy to read patterns and instructions for a Water Tower made from wood, a 3 pound coffee can and a few sundry items. ompatible with Garden Scale Railroads and Kiva's GardenTowns
More informationEntryway Locker 17 ½ 25 ½
Copyright 2015 Shanty-2-Chic.com T Entryway Locker his old world entryway locker is loaded with possibilities. Two adjustable shelves allow you to customize the storage to fit your needs. Even better,
More informationInstallation Instructions
Installation Instructions As with most building projects there's more than one way to build your storage building. But after building literally hundreds of them I believe I have figured out the easiest
More informationAssembly InstrUctions
assembly video now available online! Assembly InstrUctions The Penthouse Coop how egg-citing! Getting Started: Requirements & Tips 1 2 Put a Phillips head bit (Size: PH2) on a power drill. Ensure your
More informationPINEHAVEN SHEDS Assembly Instructions FOR LEAN-TO SHEDS
PINEHAVEN SHEDS Assembly Instructions FOR LEAN-TO SHEDS GARDEN PRODUCTS www.pinehavensheds.co.nz 5/16 hex drive bit, By asking about our products at your nearest DIY or gardening store www.pinehavensheds.co.nz
More information(2) 4 x 8 Ft. Sheets of ¾-inch Purebond Plywood Tape Measure (2) 4 x 8 Ft. Sheets of ¼-inch Purebond Plywood Pencil (1) 1 x 8 x 8 Ft.
MATERIALS: TOOLS: (2) 4 x 8 Ft. Sheets of ¾-inch Purebond Plywood Tape Measure (2) 4 x 8 Ft. Sheets of ¼-inch Purebond Plywood Pencil (1) 1 x 8 x 8 Ft. Board Carpenter s Square (1) 1 x 6 x 8 Ft. Board
More informationDiorama. How to make a diorama or model building
Diorama How to make a diorama or model building Tools required Basic Tools: Drill, Circular saw, Jig saw, Utility Knife (Stanley) Hammer, Wood Glue and Nails These are all you need to get started. Later
More informationOval Vinyl Gazebo. Assembly Manual
Oval Vinyl Gazebo Assembly Manual Gazebo Assembly Thank you for your purchase of this Gazebo. This manual is designed to simplify the assembly process, however we strongly recommend having an experienced
More informationInstallation Instructions Ascend Ceiling Systems - Stainless Pan Ceilings
Ascend Ceiling Systems - Important: Install in accordance with manufacturer s installation instructions. Failure to do so will void the warranty. Recommended Tools: Socket Wrenches, Socket Set, Cordless
More informationA Magazine Rack with a Top
A Magazine Rack with a Top Introduction: I have never come across a good free plan for a magazine rack. Yet almost all homes have one. So this is one of the few items I have made on my own, as I don t
More informationPrecut Value Shed Manual Gambrel Barn
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH
More informationWardrobe 3 doors / / /03. Assembly Instructions - Please keep for future reference / / /03
Wardrobe 3 doors Assembly Instructions - Please keep for future reference 208-9058/01 208-1749/02 208-1749/03 208-8494/01 208-1749/02 208-6471/03 Dimensions Width - 153.8 cm Depth - 58.2 cm Height - 216.6
More informationTypical Drawings for Schools
0.85 1.7 0.85 3 3 0.6 3 3 0.85 1.7 0.85 0.3 4 4 1 1 2 2 0.425 0.425 0.425 0.425 1.2 2.4 1.2 0.6 0.6 4 4 1 1 3 3 0.4 0.6 0.3 0.3 3 3 4 4 0.4 4 4 1 1 2 2 Detail of (W 1.2 x 0.4 m) Detail of (W0.6 x 0.4 m)
More informationWooden Rectangle Pergola Assembly Manual
Wooden Rectangle Pergola Assembly Manual Pergola Assembly Manual Thank you for your purchase of this Pergola This manual is designed to simplify the assembly process, however we recommend having an experienced
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationTM TM DOG HOUSE Age 9+
TM TM DOG HOUSE Age 9+ Safety First! Use eye protection, always! Use ear protection with loud power tools Stay with kids while they work! Follow tool manufacturers safety guidelines This project is recommended
More informationSustainably made in the United States. Doors Make the Difference.
Sustainably made in the United States Doors Make the Difference www.vanmillwork.com Just What You Want True stile & rail construction Better construction methods New standards & possibilities: now available
More informationCity of Manteca Boarding Requirements
City of Manteca Boarding Requirements There should be no boarding above the first floor unless entry is possible without use of a ladder, and the opening is large enough for a person to easily pass through.
More informationDIY Corner Bench with Built-in Table
DIY Corner Bench with Built-in Table Free woodworking plans for building a corner bench with a built-in table in the center. Cost: ~$75 Difficulty: Intermediate PINSPIRATION MOMMY 1 TOOLS AND SUPPLIES:
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right This brochure is your guide to preparing and installing your new kitchen. Inside you ll find tips and ideas, clear
More informationINSTALLATION GUIDE. TRANZFORM Sound TRANZFORM Space
INSTALLATION GUIDE TRANZFORM Sound TRANZFORM Space Cornell Iron Works, Inc. 100 Elmwood Ave. Crestwood Industrial Park Mountain Top, PA 18707 Phone: 800.233.8366 or 570.474.6773 Fax: 800.526.0841 INSTALLATION
More informationIntex Engineered Pergola System Installation Instructions. NOTE: See Appendix for Foundation Requirements
Intex Engineered Pergola System Installation Instructions NOTE: See Appendix for Foundation Requirements Pergola Installation, Freestanding (If pergola will be attached-to-structure, skip to page 3) 1.
More informationFree Doghouse Plans Page 1 of 2
Free Doghouse Plans Page 1 of 2 This doghouse is designed with the beginner in mind. It might even be a good project to involve the kids. The entire project requires only one sheet of plywood, two 2"x4"s
More informationBuild a Rolling Tool Tote
The rolling tool tote design calls for readily available materials: a cheap hand truck (it could be an axle and two wheels), 3/4 and 1/2 thick plywood, 1/4 thick MDF (you could use plywood or hardboard)
More information