Secret Storage Book. Part Lists. The Book
|
|
- Hector Mason
- 5 years ago
- Views:
Transcription
1 Secret Storage Book Part Lists Wood Screws ( (Werbilt flat head phillips #4 x ⅜ in) Drills Screwdrivers Hinges (2 medium and 3 small) Corner braces (¾ inches) Paint or scrapbook paper Leather Thick cardboard Lock and key ( Prime-Line U 9941 Drawer & Cabinet Lock, 5/8 in., Diecast, Stainless Steel, 5/16 in. Max. Panel) Glue: E6000 and Tacky glue Photo resistor Neopixels LED strip Wires and jumper wires Arduino Solder Soldering Iron Heat shrinks The Book To create the book, you will create 2 boxes. First cut the wood into the following sizes: (2) 5.5 x 8 in. These will act as the back and front book covers (5) 5.25 in x 1.5 in. These will act as the shorter wall edges (2) 1.5 in x 7 in. These will act as the longer wall edges (2) 1.5 in x 8 in. These will be the spine of the book (2) 5.25 in x 5 in. These will be for the interior walls of the top box. Cut one out of wood and there other in one cardboard (1) 5.25 in x 1.25 in. This will hold the lock Drill a hole with a ½ inch diameter on the top most ends of the spine pieces. You will use these to connect the wires from one box to the other.
2 To create the bottom box, use the E6000 glue to attach (2) 5.25 inches x 1.5 inches and (1) 1.5 inches x 7 inches together on the 5.5 inches x 8 inches wood back cover. Note: I like to decorate the wooden cover with leather and the wooden sides with paper or paint before attaching the pieces together. To create the top box, first drill a hole with a ¾ in diameter on the middle of the 5.25 in x 1.25 in wood.
3 Use the E6000 glue to attach (3) short wall wood pieces, (1) long wall piece, the wood piece with the lock, and the 5.25 inches x 1.25 inches together. The finish outcome should look like the pictures below (left: front) (right: back) Using E6000, glue a wooden spine to each box. Make sure that the boxes both line up together! Attach the lock onto the top box. Attach corner braces on lower end and bottom right corner on the bottom box to hold the lock in place. By doing this, the two boxes will be closed and locked together without the key.
4 Next, create a door on the back of the top box by using (3) small hinges and the cardboard piece. Attach corner braces on three sides in the interior space to keep the door in place. Also, trace around the location of the lock when the key opens the lock. Poke two holes on either sides. This will allow the wires to poke through. Use a medium size hinge to attach the spines together on the outside of the boxes. This will allow the two boxes to swing open like a book.
5 The Circuit To make the circuit, you will need a photoresistor, a neopixel LED strip, and an Arduino Solder wires on the neopixel LED strip Attach jumper wires onto the photoresistor To create the positive leads, solder a red jumper wire to a small piece of red wire (NOTE: I like to color code my wires in order to keep track of them) Solder a separate and longer red wire to the positive ends of the neopixel LED strip and the photoresistor. The two seperate red positive will connect through the metallic lock. The lock acts as a switch that turns the circuit on and off Solder the negative ends of the neopixel LED strip and the photoresistor with a blue jumper wire Solder the signal end of the neopixel LED strip with a white jumper wire. When finish, the circuit should look like this:
6 Putting it all together Weave the photoresistor and the neopixel LED strip through the holes that are ½ in diameter in size on the top ends of the spine. Glue the LED strip to the edge of bottom box. The Arduino and the wires will be inside of the top box. Screw the arduino down to the inside of the top box. Take the two Red seperate wires and have the exposed ends go through the small holes that you made earlier. When the metal lock turns and open the book, the circuit will close. Add velcro to the corner braces in the top box. Tape some of the wires in place. Tape the two seperate red wires in the area close to the small hinges in order to make sure they do not move when the cardboard piece closes and opens. Make sure you also tape the wires on the exterior of both boxes to the spine to keep the photoresistor and neopixel LED strip in place.
7 Use a 9 Volts Battery to power the Arduino and load the code onto the Arduino. Take the 5.5 in x 8 in front book covers and attach it to the front of the top box using a medium size hinge. Add final touches like decorating the exterior sides of the book with paper and the spine with additional leather to cover the hinges and wires. Optional: Add a few pieces of papers to the on the front of the top box to give it a book appearance.
Instructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationPatrol Box Plans by David J. Yarusso Troop 609
Patrol Box Plans by David J. Yarusso Troop 609 Materials List: 1. One 4 x8 sheet of ½ thick cabinet grade (birch or oak) or AC plywood. If using AC grade, use the A grade surface on the outside for a clean
More informationNEXUS SERIES CABINETS
NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions
More informationCopyright 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
General Assembly Guidelines I. Insure that all parts and hardware are available before beginning assembly. II. III. IV. Follow each step carefully to insure the proper assembly of this product. Two people
More informationDenise M. DeRose Handled Clamshell Handbag
Denise M. DeRose Handled Clamshell Handbag Materials: Wood 2 discs between 6 and 9 in diameter -- 4/4, 6/4 or 8/4 1 piece of thin hardwood ¼ inch thick and 4 x 10 Wood for waste blocks Supplies Small piece
More informationInstallation Manual MODEL NE-42
Installation Manual MODEL NE-42 GET TO KNOW YOUR UNIT 1 1. CROSS BRACES - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with 1/4 & 1/8 drill bit)
More information#11179 Wellington ARBOR
#11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationInstallation Manual MODEL ANE-42
Installation Manual MODEL ANE-42 GET TO KNOW YOUR UNIT 1 2 1. CROSS BRACES 2. SIDE BRACKETS - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with
More informationVigilant Cigar Humidor Vault. Assembly Instructions
Vigilant Cigar Humidor Vault Assembly Instructions Models: 1000, 1500, and 2000 Congratulations! You have purchased a superior cigar humidor. These humidors have been specifically designed to properly
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationSmart Lock. Showcase Lock + Door Brace (For Double Swing-Out Doors) PL401 + PL420-01
Smart Lock Showcase Lock + Door Brace (For Double Swing-Out Doors) PL401 + PL420-01 1 Overview Review entire instruction guide before starting installation. Instructions are intended for double swing-out
More information(1) 2x4 Ft. Sheet of ¼-inch Plywood. 1 ¼-inch Wood Screws. 1 ¼-inch Brad Nails ¾-inch Brad Nails Wood Glue CUT LIST:
MATERIALS: (5) 1x3x8 Ft. Boards (3) 2x4x8 Ft. Boards (10) 1x4x8 Ft. Boards (1) 1x2x10 Ft. Board (1) 2x2x4 Ft. Board (2) 1x6x8 Ft. Boards (1) 4x8 Ft. Sheet of ¾-inch Plywood (1) 2x4 Ft. Sheet of ¼-inch
More informationCloset System Installation Manual
Closet System Manual Thank you For choosing our Custom Closet Collection to fit all your needs Closets come fully assembled to make your project an enjoyable and satisfying experience. With quality Custom
More informationHow to fit an Internal Door
How to fit an Internal Door How to fit an Internal Door The following instructions are for installing a internal door only. If you have any queries please contact Cheshire Mouldings technical helpline
More informationASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL
ASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL January 2013 The SL500A is a square upright glass cabinet with a single hinged lockable door. It has five adjustable shelves plus the base. It also has an optional
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationEMAC 001 ACCESS PANEL
EMAC 001 ACCESS PANEL 900 x 600* 1200 x 600* Picture covers uneven edges Beaded can be taped and jointed for skimming Ensure the structural opening (panel size +10mm) is lined with timber or steel section.
More information" BASE CABINET
INSTALLATION GUIDE INSTALLATION GUIDE Before You Begin Installing Your Kitchen Cabinets 1. Read through installation guide to understand all steps and gather tools needed. 2. Verify that all of the hardware,
More informationDrill Press Storage Cart
Drill Press Storage Cart Richard Hicks on July 22, 2013 Drill Press Storage Cart Drill Press Storage Cart My Inspiration ShopNotes Issue 128 Changes Used casters instead of wheels Didn t build the drill
More informationSEPTEMBER 2018: MINIATURE PHOTO ALBUM
SEPTEMBER 2018: MINIATURE PHOTO ALBUM Materials and Supplies: Thin cardboard or cardstock for the album cover Attractive complementary papers Tacky Glue Glue Stick X-acto knife Scissors Strip of soft,
More informationInstallation Manual MODEL E-42
Installation Manual MODEL E-42 GET TO KNOW YOUR UNIT 2 (BOTTOM OF RACEWAY) 1 3 1. CROSS BRACES 2. ELECTRICAL RACEWAY 3. ELECTRICAL OUTLET - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver
More informationUltimate Arcade By CyberTech Design
Ultimate Arcade By CyberTech Design www.cybertechdesign.net I. Disclaimer While the information provided in this document is believed to be accurate, it may include technical inaccuracies or typographical
More informationDisassembly Instructions for Recycling June 10, 2010
Disassembly Instructions for Recycling June 10, 2010 These instructions apply to all workstation and wall products. Disassembly Once workstations or walls are dismantled as described under Disassembly
More informationCity of Manteca Boarding Requirements
City of Manteca Boarding Requirements There should be no boarding above the first floor unless entry is possible without use of a ladder, and the opening is large enough for a person to easily pass through.
More information#11179 Wellington ARBOR
#11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer
More informationLeft Unit. G. Shelf 1 pc. Small Cam Lock 6 pcs.(+1 extra) Cam Lock Screw 2 pcs.(+1 extra) Cam Lock Screw 6 pcs.(+1 extra)
88 5180 181 Art & Craft Computer Desk (Cottage Oak) IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring
More informationJewelry Cabinet. Materials: 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide. 1-4' x 8' sheet - 3/4" plywood. wood glue get 1x4's)
1 Jewelry Cabinet Materials: 1-4' x 8' sheet - 3/4" plywood 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide wood glue get 1x4's) sand paper 1-1" x 6" x 8' board wood filler 1/2 sheet - 3/16"
More informationHow to Build Your Custom Teardrop Camper. 5 x 10 Trailer. 5 Tall Cabin
How to Build Your Custom Teardrop Camper 5 x 10 Trailer 5 Tall Cabin Contact: hennesseystealth@bigteardrop.com http://www.bigteardrop.com ebay Seller ID: hennesseystealth1957 United States Copyright TXu
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationPet Door Panel Installation Manual
Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32
More informationFITTINGS, SCREWS, BOLTS, ETC.
5mm Connecting 3 Mending Plate Order number... 19-116 For 5/8 to 5/8...19-168 For 3/4 to 3/4...19-170 Packaged 5 pieces Finish: Bright Nickel Packaged 5 pieces Finish: Zinc Plated Connecting Bracket For
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 3
Kentucky 4H Wood Science Plans Notebook Plans Level 3 MATERIALS: 2 pieces wood 3/4 x 10 x 4 1 piece wood 3/4 x 12 x 4 2 pieces wood 3/4 x 3 x 2 5 1/2" 2 pieces wood 3/4 x 3 x 1 8 1 piece wood 2 x 4 x
More informationSelekta Pro 2000 Fast assembly hinges for office and commercial furniture
Fast assembly hinges for office and commercial furniture 99 The program opening angles 180 and 270 with pre-mounted pan-head screws with eccentric height adjustment ± 2 mm with eccentric overlay adjustment
More informationINSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DOOR SYSTEM (180º INSTALLATION)
INSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DO SYSTEM (180º INSTALLATION) 28539 Industry Drive, Valencia, CA 91355 Toll Free Phone: (877) 728-3874 Toll Free Fax: (888) 440-9567 Phone: (661) 775-1675
More informationInstallation Instructions. Materials Needed. Parts Included. Tools You Will Need
Installation Instructions 27 Built In Wall Oven JKP15, JKP18, JKP27, JKP45, JKP56 JKS05, ZEK937, ZEK957 If you have questions, call 800-GE-CARES or visit our website at: www.geappliances.com Before you
More informationThe Useless Machine. DIY Soldering Edition. Instruction Guide v0004
The Useless Machine DIY Soldering Edition Instruction Guide v0004 TM For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: Soldering
More informationInstallation Manual MODEL AE-46
Installation Manual MODEL AE-46 GET TO KNOW YOUR UNIT (BOTTOM OF RACEWAY) 2 5 1 4 6 3 1. CROSS BRACES 2. ELECTRICAL RACEWAY 3. SIDE BRACKETS 4. ELECTRICAL CORD COVER 5. ELECTRICAL OUTLET 6. HOT IRON REST
More informationHow to make a template to mount your plaque to a surface
How to make a template to mount your plaque to a surface A piece of heavy paper 3 4 wider than your plaque on all four sides (paper grocery bag works great too) Small amount of paint (latex dries the fastest)
More informationThe DeWils Guide to Designer Series Framed Cabinetry Installation
The DeWils Guide to Designer Series Framed Cabinetry Installation www.dewils.com The first step in the cabinetry installation process is to prepare both yourself and the work areas for the new cabinets.
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationMaking Simple Bookbinding Equipment. A Lying Press. Making Simple Bookbinding Equipment. A Lying Press. Tony Firman
Making Simple Bookbinding Equipment Tony Firman 28 1 2 27 Notes Making Simple Bookbinding Equipment Tony Firman Tony Firman Bookbinding 26 3 Making Simple Bookbinding Equipment: 2012 Tony Firman Bookbinding
More informationPalladian/ Keystone Models 202/204 Maintenance Kit
Palladian/ Keystone Models 202/204 Maintenance Kit Please read all of the instructions before you begin. Confirm that you have all the necessary tools and parts required. Allow about one hour to complete
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right This brochure is your guide to preparing and installing your new kitchen. Inside you ll find tips and ideas, clear
More informationLight Up the Room with a Light Bulb Illusion. By Laura Zinszer
Light Up the Room with a Light Bulb Illusion By Laura Zinszer lzinszer@email.com 2002 - Summer Institute Optics and Sound with Dr. Meera Chandrasekhar and Jennifer Geib Light Up the Room with a Light Bulb
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationWellington Wallbed 700 Series Assembly Instructions
Wellington Wallbed 700 Series Assembly Instructions 1. Read all instructions before proceeding. Not following instructions may result in personal harm or damage to the furniture. 2. 2 people are required
More informationTERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions
TERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions Before You Begin These installation instructions will lead you through the process of installing
More informationThe Useless Machine. Parts Only - Build Guide v0001
TM The Useless Machine Parts Only - Build Guide v0001 For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: One phillips screwdriver,
More informationVACUSEAL MODEL 200. HOT TUB PRODUCTS 233 Carrington Road Bethany CT
VACUSEAL MODEL 200 J G F G H L HOT TUB PRODUCTS 233 Carrington Road Bethany CT 06524 860-469-2580 www.vacusealcoverlift.com www.hottubproducts.com Made in USA H K E D C I A P B 10 9 8 7 6 5 4 3 2 1 0 SPAS
More informationPULLOUT SHELF ROCKLER BUILD IT WITH BUILD CUSTOMIZE
BUILD Stock Item 12229 Drawer s, 2 1 2" x 48" 63420 Baltic Birch Ply, 1/4" x 24" x 30" 38742 Maple, 3/4" x 3" x 24" 45953 100# Zinc Over-Travel Drawer Slides - Centerline 757-20" 30254 #8 x 1 1 4" Square
More information136 PLYWOOD DESK 522
136 PLYWOOD DESK 522 Simple in design and inexpensive, this plywood desk is made from a single 4- x 8-foot panel. Plywood is available with many hardwood veneers; it can also be covered with plastic laminate,
More informationDIY Stevenson Screen Part 1
DIY Stevenson Screen Part 1 Getting The Stevenson Screen Legs Ready 4 inch 10 cm 8 inch 20 cm First Part Screw holes 6 inch 15. m 2nd Part Screw holes 16 inch 40 cm 12 inch 30 cm Each Timber is 34 mm X
More informationDoor Hinges Drill-in Hinges
Drill-in hinge StarTec Frame part For timber lining frames For rebated doors Maintenance-free friction bearing To use in combination with receiver Max. door weight: 40 kg Knuckle: Ø15 mm Drilling bit Ø7.2
More informationInstalling DoorSense August Smart Lock Pro
Installing DoorSense August Smart Lock Pro First, decide how you would like to install the DoorSense. August provides two options for installation: a surface mount and a flush mount installation. The surface
More informationPlexidor Glass Conversion Pet Door Consumer Instructions
Plexidor Glass Conversion Pet Door Consumer Instructions (Rev 1 2012) Instructions for Installing a Plexidor Pet Door into Glass Sliding Glass Patio Doors French Doors Stationary Windows Other Household
More informationWALL MOUNTED FLOATING WOODEN CABINET
WALL MOUNTED FLOATING WOODEN CABINET How to make and install a floating wall-mounted Shaker-style wooden box for your DVD player and set top box for your wall-mounted flat screen TV What you'll need: Dremel
More informationMANUFACTURING INC. Specifications
Page 1 of 4 GENERAL 11 Aluminum security screen doors must be tested by a recognized testing laboratory to conform to SMA 6001-2002 Proposed American National Standard Specifications for Metal Protection
More informationExtra Wide Designer Lockers Series Installation Instructions
Extra Wide Designer Lockers 20000 Series Thank you for selecting the 20000 Series Extra Wide Designer Lockers. We are confident that the quality and construction of the lockers will prove to be a good
More informationCabinet Rim lock, Push Button type, - 25 mm backset Page 2-3
Izerwaren Order numbers 25.191. Cabinet Rim lock, Push Button type, - 25 mm backset Page 2-3 Cabinet Rim lock, backset 25 mm - 1 Minimum door thickness 19 mm ~3/4 Strike plate not included with lock Both
More informationSentinel Electronic Safe Installation Guide
Sentinel Electronic Safe Installation Guide by Rev 07/12/2004 P/N 100020 Table of Contents 1. OVERVIEW...3 2. SAFE INSTALLATION...3 2.1. TOOLS REQUIRED...3 2.2. SELECTING THE MOUNTING LOCATION...3 2.3.
More informationInstallation Instructions. Oakmont Folding Doors
Before You Start For quick and easy installation of your Oakmont folding door, read these instructions thoroughly. A few minutes of prior planning will make the job easier and ensure years of trouble-free
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationWoodware Designs -- Furniture Construction Hints
Woodware Designs -- Furniture Construction Hints 1. Purpose The following are construction hints for woodworking details used in building many of our desks. We are providing them here free for our woodworking
More informationMedia Console Table 38"
Copyright 2016 Shanty-2-Chic.com Media Console Table A sleek, modern take on a traditional concept; this console table is as stylish as it is functional and you'll have it done in a weekend. And versatile
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More information#11178 Providence ARBOR
#11178 Providence ARBOR ASSEMBLY INSTRUCTIONS TOOLS NEEDED Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Ruler Hammer or Mallet ARBOR TOP ASSEMBLY (Refer to Drawing 1) (Make 2) On clean
More informationVACUSEAL MODEL 300 & 400
VACUSEAL MODEL 300 & 400 G L HOT TUB PRODUCTS 2 Toelles Road, Suite 13 Wallingford, CT 06492 860-469-2580 www.hottubproducts.com J G F H H K E D C I A P B 10 9 8 7 6 5 4 3 2 1 0 0 1 Figure 1 2 3 4 SPAS
More informationPRIME SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS
PRIME SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationMcCue Bumper Installation Instructions
McCue Bumper Installation Instructions McCue 8" Bumper Tools Required: Saw with 10-12" blade Tape measure Flat head screwdriver Phillips screw driver Pencil or chalk line Drill with Philips driver bit
More informationINSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY
NEWAGE STEEL WELDED CABINETRY WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES ALL CABINETS MUST BE MOUNTED TO STUDS ON A SECURE WALL, AS PER THESE INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS
More informationSLATTEX (Textured Slatwall) INSTALLATION GUIDE
SLATTEX (Textured Slatwall) INSTALLATION GUIDE Preparing for the Installation: Here are some suggestions to help you to help you simplify the installation process and maximize the beauty of your 3D Textured
More information1 Door Wall Unit ASSEMBLY GUIDE. Page 1 of 7 14/04/2009 Revision 3. WARNING: Contains small parts, keep out of reach of children.
ASSEMBLY GUIDE 1 Door Wall Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please contact 1800
More informationItem # Thanks for shopping with Improvements!
Thanks for shopping with Improvements! Hampshire -Door Cabinet Item #5505 To order, call -800-64- West Chester, OH 45069 Made in China PR-6 If you have questions regarding this product, call -800-64- Mon.-Fri.
More informationWorktop. Weight Capacity. 100 lbs. 21 Corner Worktop. 48 Worktop. Fits over 2 Cabinets. 72 Worktop. Fits over 3 Cabinets. 200 lbs. 150 lbs.
Bold.0 Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping
More informationEXTRUTECH PLASTICS, INC. Custom Extruder of Close Tolerance Profiles
PVC SINGLE DOOR INSTALLATION INSTRUCTIONS Single Pre-Hung Doors are shipped assembled in most cases ready for installation. Check the sill; in some cases you may want a sill in this door or if not requested
More informationThis instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.
This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams
More informationInstallation Instructions for Converting Hinging on Roll-In Refrigerators
Installation Instructions for Converting Hinging on Roll-In Refrigerators Part number 161651 hinge conversion kit RH is for converting a right side hinged door and part number 161652 hinge conversion kit
More informationASSEMBLY INSTRUCTIONS MANUAL
PAGE 1 OF 9 RECOMMENDED TOOLS FOR ASSEMBLY: ALLEN WRENCH (INCLUDED) BOX WRENCH (INCLUDED) PHILLIPS SCREW DRIVER (NOT INCLUDED) PARTS IN CARTON: ALLEN WRENCH SCREWS (20 EACH) ROUND HEAD SCREWS (8 EACH)
More informationPackage contains. Required tools and consumables:
Thank you for purchasing the TriTrix MTM Transmission Line cabinet kit. This cabinet kit was precision cut using CNC machinery for the best possible fit and finish. With a little time and patience, your
More informationC PART LIST HARDWARE LIST. Kitchen Cart IMPORTANT NOTE
88 9200 006C Kitchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken
More informationHomestead Bar Cabinet IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent s
88 5527 991 Homestead Bar Cabinet IMPRTANT NTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts.
More informationFor our first radio, we will need these parts: -A sturdy plastic bottle.
For our first radio, we will need these parts: -A sturdy plastic bottle. I have used the plastic bottle that hydrogen peroxide comes in, or the bottles that used to contain contact lens cleaner. They are
More informationHOW TO HOME IMPROVEMENT INSTRUCTIONS (Steps to make changes and before and after photos) Entrance to Front and Back of House
HOW TO HOME IMPROVEMENT INSTRUCTIONS (Steps to make changes and before and after photos) Entrance to Front and Back of House 1. Outdoor Grab Bar To install a weatherproof grab bar into a brick wall: 1.
More informationHow to Build the Robotics++ V2 Robot. Last Edited Nov
How to Build the Robotics++ V2 Robot Last Edited Nov. 15-2014 www.roboticscity.com 1 Completed Robotics++ V2 Robot. More views of completed robot can be found at the end of this instructions manual The
More informationBuilding a Shadow Box - Instructions
Building a Shadow Box - Instructions Miniatures are art. And like all good art, it should be framed to enhance the art and to focus the viewers attention. Tools and Supplies Required 1. Large Cutting Mat
More informationInstallation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers
Installation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers This tutorial is designed to aid you in installation of a console customs rapid
More informationInstructions. for the installation of tamperpoof exterior screws. Kit KTPS-SM fits all modular Prodigy except EH222 and C2648
Kit KTPS-SM fits all modular Prodigy except EH222 and C2648 Screw Use Used 5-16 x ¾ truss head machine 4 bin to unit fasteners ¼ - 20 x ½ pan head machine 4 drain fitting(s) attachment, receiver bracket
More informationPROJECT PLAN TOOL CHEST
BUILD IT WITH ROCKLER PROJECT PLAN TOOL CHEST FEATURING ROCKLER S BUILD QUESTIONS? Go to www.rockler.com or call 800-279-4441 Stock # Item 63420 1/4" x 24" x 30" Baltic Birch Plywood 63446 1/2" x 24" x
More informationI n s t a l l a t i o n S p e c i f i c a t i o n s
13-27 I n s t a l l a t i o n S p e c i f i c a t i o n s f o r S o l i d P a n e l R e a d y ( o p ) a n d G l a s s F r a m e d P a n e l R e a d y ( o g ) PRESERVE THE MOMENT & INSTALL GUIDE 13 INSTALLATION
More informationPivot-Door Downdraft Cabinet Plans
Pivot-Door Downdraft Cabinet Plans Finished Cabinet Closed Open Exploded View Introduction This simple downdraft-style dust collection cabinet is a great way to keep your shop cleaner and keep your router
More informationCongratulations on purchasing the Spirit Rails Magnetic Attach that allows easy wand to pack removal and reattachment by just getting close!
Introduction Congratulations on purchasing the Spirit Rails Magnetic Attach that allows easy wand to pack removal and reattachment by just getting close! The Spirit Rails Magnetic Attach Kit is designed
More informationManufactured and Distributed by Multi-Housing Depot. Acacia Cabinetworks. Installer Pro Training
Manufactured and Distributed by Multi-Housing Depot Acacia Cabinetworks Installer Pro Training Table of Contents Program Overview Program Requirements Common Install Glitches & Recommendations Common Site
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
More informationHigh performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
More information