Fan Back Adirondack Chair Assembly Instructions How To Assemble Your Chair in 12 Easy Steps Parts List 5 9
|
|
- Noel Cain
- 5 years ago
- Views:
Transcription
1 Fan Back How To Assemble Your Chair in 12 Easy Steps Parts List #1 (2) frame, left & right #2 (2) 20" legs, left & right #3 (6) 20" seat slats #4 (1) lower canoe #5 (7) back slats #6 (1) curved seat slat #7 (2) front arm supports #8 (2) back legs, left & right #9 (2) arm rests, left & right #10 (1) middle canoe #11 (1) back arm support #12 (1) top canoe #13 (1) front Skirt Hardware (43) 1-5/8" screws (8) 3" screws (7) 2-1/2" screws (11) 2" screws (2) 2-1/2 bolts (2) washers (2) nuts Tools: Best to use power drill with 2" long #2 phillips bit and 9/16" wrench or crescent wrench Glue: Buy a small bottle of "Tite bond II Premium wood glue, weather proof or something similar. (Lowe's or Home Depot) Note: Directions stating left and right are as you sit in the chair Note: Use 1 5/8" screws unless otherwise stated Note: When driving in screws, make them very snug, but don't let head dig into wood very far or cracking may occur Be patient, and Take Your Time. You will need a flat, solid work surface, such as a table or patio when attaching the legs to ensure that your chair sits level Caution: Rarely, but occasionally a knot may be in the path of a screw, if this happens, the knot will have to be pre drilled, or the screw may break off Assembly Sequence: Layout all pieces as illustrated above Step #1 Using 1 5/8 screws, glue & attach #13 front skirt to the front edge of #1 left & #1 right base supports. 1-5/8 Wood Screw Step #2 Temporarily attach lower canoe #4 to bases as shown in photo. DO NOT glue or tighten the screws all the way. (This is to temporarily hold the two bases 22 apart from front to back). Glue & attach #13 Front Skirt, and the 5 #3 seat slats with 1-5/8 screws. Attach the #6 curved seat ¼ Spacing slat with 1-5/8 screws. Note: Space between slats the seat slats and half round about 1/4 apart. Remove lower canoe #4. 1
2 Page 2 Step #3 Take #4 lower canoe and attach 7, #5 back slats to canoe. Center back slats on canoe. The back slats are numbered 1 through 7. Make sure counter sunk holes on canoe are on top, not on bottom. Also make sure there is a nice rounded curve on top of back slats when fanned out before screwing slats to lower canoe. The pieces should be snug together at the bottom. Use 2 screws. It is ok to let screw dig into wood a little as you attach back Center Back Slats on Lower Canoe with holes on top Use upper canoe for temporary support slats to lower canoe. (You can use middle canoe #10 to temporarily hold up the top end of back slats while positioning and screwing lower end of slats onto lower canoe. 18 between lower canoe and middle canoe) Do not glue the slats to lower canoe Nice Round Curve 1 Step #4 Note: You have limited working time (about 5 or 10 minutes) before the glue begins to tack. To lengthen working time, wipe areas to be glued with a damp rag before applying glue. Apply glue around bolt hole and attach #2 left and right legs to frames using bolts, washer and nut. Counter sunk pre-drilled holes at the top of the legs are on the inside of leg when attached to base. Step #5 Turn base with legs attached right side up and rotate legs so bottom of legs are level with floor. Screw on nuts snuggly, but not tight. You will probably have to slightly rotate legs later in the assembly process. Note: You have limited working time (about 5 or 10 minutes) before the glue begins to tack. To lengthen working time, wipe areas to be glued with a damp rag before applying glue. Step #6 Take the #4 lower canoe with the #5 back slats attached and glue and screw the canoe/back slat assembly to the #1 bases using 2-1 5/8 screws on each side Step 6 Completed with back assembly attached to chair frame
3 Page 3 Step #7 Attaching back legs #8. There is a left and right back leg. Position bottom of leg within the lines drawn on the inside of the base. Top of leg slopes away from back rest. Only fasten each leg with one 1-5/8 screw for now. You will put in the second screw in step #11 Step #8 Take middle canoe #10, glue & lay on top of back legs. Position so pre drilled holes are directly over top of back legs. Back of canoe slightly overhangs back edge of leg. Put one 2 screw in each end while positioning canoe. Drive the second 2 screw in each end once piece is positioned in place. Attach back legs with Only One Screw for this step Step #9 A. Glue and attach #7 front arm supports at the top, center, on the outside of front legs using two screws on the inside of the leg. B. Attach rear arm support #11 to outside of back leg. Top of support is 23 from floor. Support is not centered on width of leg. See dashed line. Flush with top of leg Overhang Slightly 23 Step #10 A. Apply liberal amount of glue on top of front legs. (Wipe up any runs with wet rag after step 11.) B. Place right arm on top of leg and rear support. C. Make sure back end of arm is flush with back edge of back leg. D. 1 over hang on inside of front leg. A. B. C. Flush with back of leg D.
4 Page 4 Step #11 (Repeat Steps 10 and 11 for Left Arm Rest also) A. 1. While pushing down on top of arm with hand, screw a 3 screw up thru arm support. 2. Toe nail a 3 screw (drive screw at an angle) thru top front & back edge of front leg into arm rest. B. Drive 2-1/2 screw into back arm rest support. C. Drive 2 1-5/8 screws into side of back leg into arm rest. Finish tightening bolts on front legs. & putting 2nd screw in bottom of back legs A. B. Attach arms to back arm rest supports with 2-1/2 screws C. Step #12 Fan outside back rest slats out beyond end of middle canoe by 1/4. Screw a 3 screw into ends of middle canoe into outside back slats. Evenly space rest of back slats and screw 5 2 1/2 screws into five remaining seat backs. Attach #12 top canoe about 5 1/2 above middle canoe. 1.Attach arm rests to supports with 3 Screws 2. Toe Nail Screws through front and back edge of front leg with 3 screws Congratulations! Attach arms to back legs with 1-5/8 screws In 12 easy steps, you have assembled your chair and are now ready to enjoy it. Did you see our folding Adirondack chair? Check it out today at We also offer a wide selection of Tables, Benches and other chair styles, all of which would be an excellent compliment to your new Adirondack chairs.
5 Page 5 Finishing Cedar Should you desire a different look, cedar readily accepts most stains, outdoor paints and wood preservatives. While you can varnish outdoor furniture made of oak or other hardwoods, we do not recommend using varnish on cedar: A marine grade spar varnish will work well, but will flake if the furniture gets dented, leaving an unsightly appearance. Clear oil finishes, such as linseed oil, or teak oil work very well, as does a deck sealer such as Thompson's. Clear oil will have to be reapplied every year or two by simply wiping on another coat. A deck sealer will protect the wood from the elements, but unless you use a sealer with UV blockers, will not prevent the wood from turning grey from exposure to the sun. Be sure to read the can carefully to make sure you will get the look you want. If you desire an "old" look for your furniture, but still want to ensure a good long life, a deck sealer without UV protection is a very good choice. Deck sealer will need to be reapplied every couple of years, sometimes more, depending on the amount of wear on the seats and arms of your furniture Cedar will also readily accept most outdoor wood stains and exterior paints. Keep in mind that painted wood furniture, much like a wood fence or wood house siding, will need to be repainted every 5 to 10 years. Always be sure to follow the recommendations of the finish manufacturer. When applying finish, it is ideal to finish the parts before assembly, as it will be difficult to apply finish between the seat and back slats once assembled. Do not apply finish to the areas where glue will be applied! It is recommended that you mask off these areas. Alternatively, you can assemble the major components of your chair before applying the finish: Assemble the seat assembly (frames, seat slats), the back assembly (lower canoe, back slats and top canoe), the front leg assemblies (legs and front arm supports) and the back leg assemblies (back legs and back arm supports), using glue where indicated in the instructions above, before applying the finish. You will stall have to mask off certain areas, such as where the back assembly and the front and back legs attach to the frames, and where the arm rests attach to the front and back legs. Assembling the major components before applying the finish will certainly make applying the finish easier than waiting until the chair is fully assembled.
2. Arrange Seat Section and Back Section together as follows:
Hello congratulations on the purchase of your 6 swing. I sincerely hope you enjoy! If you have friends or family that would like to purchase please have them contact me directly at 337-540-6162 or cruzeswingsandthings@yahoo.com.
More informationADULT. Adirondack / Muskoka Chair Plans
ADULT Adirondack / Muskoka Chair Plans Materials List 3/4" x 9 1/2" (1.9cm x 24.1cm) redwood, cedar or pine boards. Six, 8' (2.44m) boards should make one chair depending on knots and layout. You can also
More informationOld Adirondack Inc. Natural Cedar Furniture
Old Adirondack Inc. NOTE: WHITE CEDAR Northern White Cedar is one of nature s most unusual woods, Because most cedar grows near swampy water basins, it has a slow rate of decay and a natural resiliency
More informationOld Adirondack Inc. Natural Cedar Furniture
NOTE: WHITE CEDAR Northern White Cedar is one of nature s most unusual woods, Because most cedar grows near swampy water basins, it has a slow rate of decay and a natural resiliency to rot and disease.
More informationPa For assistance with assembly, please contact customer service
ITEM NAME: Belham Living Vella Eucalyptus Adirondack Chair -White SKU: TDJ115 For assistance with assembly, please contact customer service 1-888-880-4884 Pa- 1-1 1/5 PRE-ASSEMBLY PREPARATION:! DO NOT
More informationITEM NAME:Carmona Faux Wood Slat Extension Table SKU: ALZ For assistance with assembly, please contact customer service /5
ITEM NAME:Carmona Faux Wood Slat Extension Table SKU: ALZ1016-1 For assistance with assembly, please contact customer service 1-888-880-4884 1/5 PRE-ASSEMBLY PREPARATION: DO NOT LET CHILDREN PLAY IN OR
More informationFor assistance with assembly, please contact Hayneedle Customer Care Center
ITEM NAME: Coral Coast Lindos 3 Piece Folding Patio Bistro Set SKU: NWF080-1 For assistance with assembly, please contact Hayneedle Customer Care Center 1-888-880-4884 1 1/6 PRE-ASSEMBLY PREPARATION:!
More informationPa For assistance with assembly, please contact customer service ITEM NAME: Belham Living Vella Eucalyptus Porch Swing - White
ITEM NAME: Belham Living Vella Eucalyptus Porch Swing - White SKU: TDJ25 For assistance with assembly, please contact customer service -888-880-4884 Pa- - /5 PRE-ASSEMBLY PREPARATION:! DO NOT LET CHILDREN
More informationBuild It: The Most Amazing Cooler Bench Ever
Build It: The Most Amazing Cooler Bench Ever wooditsreal.com/2017/04/28/build-it-cooler-bench-free-plans/ A bench. A cooler. Put them together and what do you get? The most amazing Cooler Bench you ve
More informationFor assistance with assembly, please contact the Customer Care Center
ITEM NAME: Coral Coast Pleasant Bay 4 ft. Curved Back Outdoor Glider Loveseat SKU: NWF07 / NWF08 For assistance with assembly, please contact the Customer Care Center 1-888-880-4884 1/6 PRE-ASSEMBLY PREPARATION:!
More information1500 ROCKING CHAIR ASSEMBLY INSTRUCTIONS
1500 ROCKING CHAIR ASSEMBLY INSTRUCTIONS Thank you for purchasing a quality select hardwood rocking chair. This rocking chair is made exclusively by the Hinkle Chair Company, a family-owned business that
More informationDirect Importers of the Finest Exotic Hardwood Decking, Lumber, & Flooring
Direct Importers of the Finest Exotic Hardwood Decking, Lumber, & Flooring These Instructions can be found online at: http://www.advantagelumber.com/how-to/buildwoodstoragebox.html Material List 72 FEET
More informationFor assistance with assembly, please contact Hayneedle Customer Care Center
ITEM NAME: Belham Living Avondale Outdoor Adirondack Chair SKU: NWF06 -, NWF06-, NWF09-, NWF09- For assistance with assembly, please contact Hayneedle Customer Care Center -888-880-4884 /7 /7 PRE-ASSEMBLY
More informationPage For assistance with assembly, please contact customer service ITEM NAME: Belham Living Shoreline Adirondack Rocker
ITEM NAME: Belham Living Shoreline Adirondack Rocker SKU: TDJ068 / TDJ069 / TDJ117 / TDJ118 / TDJ119 For assistance with assembly, please contact customer service 1-888-880-4884 Page - 1-1 1/5 PRE-ASSEMBLY
More informationASSEMBLY INSTRUCTIONS ITEM NO. D S
ASSEMBLY INSTRUTIONS ITEM NO. D0-0S GIA ROUND DINING TABLE GIA DINING HAIR (SET INLUDES HAIRS) This page lists all the contents included in the Box. Please take time to identify the hardware as well as
More information10X12 Arched Breeze Pergola Assembly Manual Outdoor Living Today
10X12 Arched Breeze Pergola Assembly Manual Outdoor Living Today ITEM# BZ1012ARCH Revision 2 March 25th/2015 Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your local building
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationMedium Pro Table Top Stand
Medium Pro Table Top Stand Build Manual Thank you for purchasing a Foam-Flite model airplane stand. Your Foam-Flite stand was designed by modelers just like you looking for an economical and versatile
More informationFor assistance with assembly, please contact customer service
ITEM NAME: Coral Coast Bellora Acacia Chaise Lounger with Pullout Table SKU: NWF056-1 For assistance with assembly, please contact customer service 1-888-880-4884 1/6 PRE-ASSEMBLY PREPARATION:! DO NOT
More informationADIRONDACK CHAIR. Model 97458
ADIRONDACK CHAIR Model 97458 ASSEMBLY And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the
More informationGlenwood Canyon Collection Item No. OF-1021
Glenwood Canyon Collection Item No. OF-02 For assistance with assembly, please contact DTYStore.com Customer Satisfaction Center 866-27-855. CS@DTYStore.com Made in Vietnam Glenwood Canyon Collection OF-02
More informationOld Adirondack Inc. Natural Cedar Furniture
Old Adirondack Inc. Natural Cedar Furniture NOTE: WHITE CEDAR Northern White Cedar is one of nature s most unusual woods, Because most cedar grows near swampy water basins, it has a slow rate of decay
More informationASSEMBLY INSTRUCTIONS ITEM NO. D S
ASSEMLY INSTRUTIONS ITEM NO. D435-60S MILO RETANGLE DINING TALE MILO DINING HAIR (SET INLUDES 4 HAIRS, ENH) This page lists all the contents included in the ox. Please take time to identify the hardware
More informationFor assistance with assembly, please contact Hayneedle Customer Care Center
ITEM NAME: Belham Living Kimbro Lutyens Outdoor Wood Bench with Cushion SKU: TDJ168 For assistance with assembly, please contact Hayneedle Customer Care Center 1-888-880-4884 1 1/ PRE-ASSEMBLY PREPARATION:
More informationSunjoy L-BG014PST Boulevard Living Arch Design Steel Bridge. Owner s Manual IMPORTANT
Sunjoy L-BG014PST Boulevard Living Arch Design Steel Bridge Owner s Manual IMPORTANT Thank you very much for choosing Sunjoy Group. Please take time to read these instructions thoroughly and follow each
More informationOld Adirondack Inc. Natural Cedar Furniture
Old Adirondack Inc. NOTE: WHITE CEDAR Northern White Cedar is one of nature s most unusual woods, Because most cedar grows near swampy water basins, it has a slow rate of decay and a natural resiliency
More informationTHE PODIUM MUSIC STAND
THE PODIUM MUSIC STAND 1 Set Assembly Instructions Wooden Parts: a. 1 Column b. 2 Long Slide Pieces c. 2 Slide Spacers (1 long & 1 short) d. 4 Feet e. 2 Fork Pieces f. 1 Fork Spacer g. 2 Long Desk Frame
More informationPlease Do Not Return Your Item to the Retailer
Please Do Not Return Your Item to the Retailer Thank you for your purchase of an Epic Furnishings item You should enjoy many years of trouble free, dependable use If for any reason you are missing parts,
More informationDIY RUSTIC HALL TREE
DIY RUSTIC HALL TREE *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationDIYdeals - Assembly Instructions for Raised Garden Decks
DIYdeals - Assembly Instructions for Raised Garden Decks Size: 2.5m (8'2") wide Return to website www.diydeals.com Before commencing : Check the size of deck you are building from the list below and if
More informationPROJECT PLAN. 3-hour cedar bench
PROJECT PLAN 3-hour cedar bench This article originally appeared in The Family Handyman magazine. For subscription information, visit www.familyhandyman.com Please note that pages that appeared in the
More information1200 SIDE TO SIDE PORCH ROCKER ASSEMBLY INSTRUCTIONS
1200 SIDE TO SIDE PORCH ROCKER ASSEMBLY INSTRUCTIONS Thank you for purchasing a quality select hardwood rocking chair. Your chair comes with a rich heritage and will become a treasured family heirloom.
More informationSLAT/RUSH/CANE ROCKING CHAIR ASSEMBLY INSTRUCTIONS
SLAT/RUSH/CANE ROCKING CHAIR ASSEMBLY INSTRUCTIONS COMPLETE INSTRUCTIONS FOR THE FOLLOWING ROCKERS Ashton 700 Bradley 200/1200 Cross Creek 300 Collegiate 200SC Cumberland 250/1250 Highland Rim 7 Kensington
More information12ft Octagon Bayside Gazebo Assembly Manual
We recommend reviewing this Assembly Manual thoroughly before starting this project. Become familiar with the tools required and where and when assistants are necessary. If you re planning on finishing
More informationEND FRAMES. End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 36" 34" 7/16" pilot hole. 5 1/2" x 1/2" lag bolt 8" wheel 23"
END FRAMES End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 23" 17 1/2" (B) (B) Measure from the bottom of your stone to 1" below the lip to get your measurement. 17 1/2"(B) 36" 34" 1/2" flat
More informationPROJECT PLANS OUTDOOR SERVING CART
R PROJECT PLANS OUTDOOR SERVING CART Make outdoor entertaining easy with this serving cart. It offers lots of space for storing food, tableware, and outdoor supplies, plus it cradles bottles where they
More informationOld Adirondack Inc. Natural Cedar Furniture
Old Adirondack Inc. NOTE: WHITE CEDAR Eastern White Cedar is one of nature s most unusual woods, Because most cedar grows near swampy water basins, it has a slow rate of decay and a natural resiliency
More information12X20 Breeze Pergola Assembly Manual Outdoor Living Today
12X20 Breeze Pergola Assembly Manual Outdoor Living Today Revision #10 July 21th, 2015 Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your local building permit office to
More informationCedar Picnic Table - Model 24 Assembly Manual
Revision #3 June 27th, 2017 Thank you for purchasing a Cedar Picnic Table. Please take the time to identify all the parts prior to assembly. Please use Safety Eye wear and Gloves while Assembling. Be sure
More information10ft Octagon Bayside Gazebo Assembly Manual
We recommend reviewing this Assembly Manual thoroughly before starting this project. Become familiar with the tools required and where and when assistants are necessary. If you re planning on finishing
More information#850 PORCH ROCKER ASSEMBLY INSTRUCTIONS
#850 PORCH ROCKER ASSEMBLY INSTRUCTIONS Thank you for purchasing a quality select hardwood rocking chair. Your chair comes with a rich heritage and will become a treasured family heirloom. If you should
More information10 Octagon Cedar Gazebo Assembly Instructions
10 Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/22/09 10 Cedar Gazebo Assembly Instructions
More informationParts list: Original Bear Chair BC Bear chair Nederland Postbus AM Zeist
INSTRUCTIONS KIT BEAR CHAIR BC201 Parts list: NR. parts Quanty Legs 2 Seat slats 6 Arm support 2 Triangles 2 5. Arms 2 Additional Arm Support 2 Struts 2 Sides, left (L) en right (R) 2 Bottom Back Support
More informationE. Front Stretcher 1 pc. 1 pc. 1 pc. M8x38 Wood Screw (long) 1 pc. (+1 extra) M4x19 Wood Screw (short) 12 pcs. (+1 extra)
88 5134 26 Bench Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions
More informationAdjustable Hammered Dulcimer Stand
Adjustable Hammered Dulcimer Stand Musicmaker s Kits (Hwy 36 behind Joseph s Restaurant) P.O. Box 2117 Stillwater MN 55082 651 439 9120 www.harpkit.com PARTS LIST: 1 Set of Assembly Instructions A. 2 front
More informationChain Drive Vise. Installation Instructions. (revised 11/29/2018)
Chain Drive Vise Installation Instructions (revised 11/29/2018) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step
More informationWALLBED Assembly Instructions
WALLBED Assembly Instructions 1 Congratulations and a Big Thank You for your purchase of a Wallbed Gallery Murphy Bed! We sincerely appreciate your business! First a few words of advice and caution: 1.
More informationDIY Outdoor Console Table Addicted2DIY.com
DIY Outdoor Console Table Addicted2DIY.com *Before beginning this project, please read through all of the plans. Always use safety precautions whenever using power tools and follow the manufacturer s suggested
More information104 PORCH SWING ASSEMBLY INSTRUCTIONS
104 PORCH SWING ASSEMBLY INSTRUCTIONS Thank you for purchasing a quality porch swing. The product you have purchased requires some assembly. This item has been carefully inspected before packing to ensure
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationBIG LOTS ASSEMBLY INSTRUCTIONS HARLOW 6PCS DINING SET ITEM NO PK SKU NO
BIG LOTS ASSMBLY INSTRUCTIONS HARLOW 6PCS DINING ST ITM NO. 15100-6PK SKU NO. 810321491 Big Lots Customer Care Phone # : 1-866-BIGLOTS(1-866-244-5687) mail Add : Talk2Us@BigLots.com 'For spare screw and
More informationChain Drive Vise. Installation Instructions. (revised 05/04/2016)
Chain Drive Vise Installation Instructions (revised 05/04/2016) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step
More informationBIG LOTS ASSEMBLY INSTRUCTIONS 6PCS PU DINING SET ITEM NO. BIG-178 SKU NO
BIG LOTS ASSMBLY INSTRUCTIONS 6PCS PU DINING ST ITM NO. BIG-178 SKU NO. 810110498 Big Lots Customer Care Phone #: 1-866-BIGLOTS(1-866-244-5687) mail Add: Talk2Us@BigLots.com 'For spare screws and bolts,
More informationASSEMBLY INSTRUCTIONS
MODEL: FH144119 ASSEMBLY INSTRUCTIONS FINGERHUT ATTENTION DO NOT RETURN TO THE STORE Contact MD Sports Customer Service * For additional resources and Frequently Ask Questions, please visit us at themdsports.com
More information8X10 Breeze Pergola Assembly Manual Outdoor Living Today
8X10 Breeze Pergola Assembly Manual Outdoor Living Today Revision #11 Jan 18th, 2018 Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your local building permit office to determine
More informationRoof Rack Installation Instructions
Roof Rack Installation Instructions CAUTION: Do not use the mounting hardware contained in this roof rack kit for installation on Fiberglass or Composite Plastic surfaces. Supplemental hardware pack, part#
More informationModel #SH & CH SH Pine CH Naturaline
Model #SH304-101 & CH304-101 Assembly Manual SH304-101 Pine CH304-101 Naturaline Component Parts A 2 ea. Angled Rail - 2 x 4 x 107-1/8" B 1 ea. Center Angled Rail - 2 x 4 x 107-1/8" C 9 ea. Rock Board
More informationUSE AND CARE GUIDE. Adirondack Chair - Natural. Product Code: D71 M34495 KSN: UPC Code: Date of Purchase: / /
USE AND CARE UDE Adirondack Chair - Natural Product Code: D71 34495 SN: 06260668-6 UPC Code: 849275001073 Date of Purchase: / / 1 Thank you for your purchase Thank you for your purchase! We are pleased
More informationLuna Cedar Sauna Assembly Instructions
Luna Cedar Sauna Assembly Instructions Requirements: * 2 People (recommended) * Step or Extension Ladder * Cordless Drill (we supply the bit) * Tape Measure * Staple Gun * Utility Knife Luna Cedar Sauna
More informationHeartland Pergola. Assembly Manual
Heartland Pergola Assembly Manual Pergola Assembly Manual Thank you for your purchase of this Pergola This manual is designed to simplify the assembly process, however we recommend having an experienced
More informationMaking Simple Bookbinding Equipment
Tony Firman 20 1 2 19 Notes Tony Firman Tony Firman Bookbinding 18 3 : 2012 Tony Firman Bookbinding P.O. Box 507 Haslet, TX 76052 www.tonyfirmanbookbinding.com 4. When all the tapes have been pinned in
More informationFor assistance with assembly, please contact the Customer Care Center
ITEM NAME: BELHAM LIVING BRIGHTON OUTDOOR STORAGE DECK BOX WITH CUSHION SKU: TDJ149-1 For assistance with assembly, please contact the Customer Care Center 1-888-880-4884 1 1/5 PRE-ASSEMBLY PREPARATION:!
More informationDundalk LeisureCraft Cedar Pod Sauna Assembly Instructions
Dundalk LeisureCraft Cedar Pod Sauna Please read and understand the complete instructions prior to assembly and use of your sauna. Customer agrees not to hold Dundalk LeisureCraft Inc. and any of its authorized
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 4
Kentucky 4H Wood Science Plans Notebook Plans Level 4 MATERIALS NEEDED: Note: 1" wood may be 3/4" thick and 2" x 2" may be 1 1/2" x 1 1/2" 2 pieces wood 1 x 3 x 17 1 piece wood 1 x 3 x 14 3/4" 2 pieces
More information1531 Fort Add On **!!IMPORTANT-PLEASE READ!!**
1531 Fort Add On **!!IMPORTANT-PLEASE READ!!** This Add-On kit will require you to deviate from the main instruction manual. Please follow the outline below so that you will know what steps to be aware
More informationPhase Two. The Skirt, Play Area and Sub Table ( continued )
Dry fit the skirt in place and make sure all is tight. Drill a countersink screw hole on the back of the skirt down where you will connect it to the bull nose. Make three holes on each board (ends and
More informationASSEMBLY INSTRUCTIONS
TM MODEL: 44119-1 ASSEMBLY INSTRUCTIONS Blain's Please contact us before returning the product to the store. Toll Free: 877-82-814 Register Now on themdsports.com and Earn a One-Year Warranty for Free!
More informationWallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS
Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note
More information10, 12 &14 Oval Gazebo Floor
0, 12 &14 Oval Gazebo Floor Revision: 2-26-03 Run: - BEFORE YOU BEGIN - Always wear OSHA-APPROVED safety glasses throughout assembly process First... Read these instructions thoroughly before you begin
More informationSTARK RANGE. Coordinated range of robust softwood construction seating and tables. tel:
Coordinated range of robust softwood construction seating and tables Stark is a comprehensive range of benches, seats, tables and picnic tables that can be used independently or as a coordinated suite
More informationsouthpaw enterprises, inc.
southpaw enterprises, inc. Store these instructions with the enclosed maintenance checklist in a safe place. You may also access them on our website. Instruction Sheet Convertible Climbing Wall - Block/Brick
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationBarrel Sauna Installation & Owner s Manual
Barrel Sauna Installation & Owner s Manual In addition to reading this manual through to the end before proceeding with assembly you may find our instruction video helpful. You can find it at: youtube.com/user/almostheavensauna
More informationBIFOLD FUTON FRAME TRINITY ARM. Seat Rails and Slats x 1. *Note: Use 4pc of 100mm Bolts and 4pc of 60mm Bolts to attach the arms to the Stretchers.
1A Parts in this box. 2pc with extra holes 2pc with extra holes & plastic stoppers Arms x 2 Back Rails and Slats x 1 Full Size: Slat Supports x 6 3pc are longer for the Back deck Back Side Rails x 2 Seat
More informationAssembly Instructions GARDENA GAZEBO
Assembly Instructions GARDENA GAZEBO Item# L-GZ136PST-9C SKU# 7143514 WARNING In order to reduce the risk of personal injury and damage to equipment, basic safety precaution should always be followed when
More informationGrand Garden Chalet 6X3 Assembly Manual - Costco
Revision #16 March 22nd, 2013 Grand Garden Chalet 6X3 Assembly Manual - Costco Thank you for purchasing a Grand Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use
More information6x6 Maximizer Storage Shed Assembly Manual Version #9 Feb 26th, 2015
6x6 Maximizer Storage Shed Assembly Manual Version #9 Feb 26th, 2015 Thank you for purchasing a 6x6 Maximizer Storage Shed. Please take the time to identify all the parts prior to assembly. Please Note-
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationHow to Build A Porch Swing
How to Build A Porch Swing SUPPLIES USED Tape measure Drill 2.5" Wood Screws 1.5" Wood Screws 2" Finishing nails Hammer (or nail gun if you're lucky) Sand paper/ Electric sander Exterior paint Safety glasses
More informationKD Table Base Assembly and Top Attachment Instructions
KD Table Base Assembly and Top Attachment Instructions 4011xx 5000xx 7014xx 8001xx 8206xx Congratulations on the purchase of your Tropitone furniture. Read through all steps before starting assembly. CAUTION:
More informationStrata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached Back Panel
More informationBELGIAN EXT. REC DINING TABLE
BELGIAN EXT. REC DINING TABLE Date: Williams 20 Jul. 2015 Sonoma Product Information Dept. www.williams sonoma.com Page 1 of 5 Page 1 of 5 Important Safety Instructions: Please read all instructions carefully
More informationHandymanWire - Picnic Table Plans
Page 1 of 5 HandymanWire Appliances Attics Automobiles Basements Cabinets & Counters Ceilings Decks Doors & Windows Drywall Electrical Flooring Garages Heating Masonry Miscellaneous Outside Painting Plumbing
More information12ft X 12ft Attached Breeze Pergola Assembly Manual. Outdoor Living Today. (For Both 9 and 12 High Posts) June 1st/2012 Version #4
12ft X 12ft Attached Breeze Pergola Assembly Manual (For Both 9 and 12 High Posts) Outdoor Living Today June 1st/2012 Version #4 Note: Installation of Wall Side Girders (P) and Wall Mount Brackets (M)
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN ORIENTAL GARDEN ARBOR PLAN This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been paid for on your behalf by JET Tools,
More informationsouthpaw enterprises, inc.
southpaw enterprises, inc. Instruction Sheet C-STAND 7100 Store these instructions in a safe place or with the enclosed maintenance checklist Take time to familiarize yourself with the use and maintenance
More informationMasterpiece Module Kits N T-trak Module Kit Assembly Instructions
Masterpiece Module Kits N T-trak Module Kit Assembly Instructions For tips, watch Instructional Video at http://www.youtube.com/watch?v=fklebffclau Tools Required flat, sturdy work surface Quality grade
More information6X3 Patio Garden Shed Assembly Manual
Thank you for purchasing a 6x3 Patio Garden Shed. Please take the time to identify all the parts prior to assembly. Revision #4 July 6th, 2016 6X3 Patio Garden Shed Assembly Manual Please use Safety Eyewear
More informationOWNER'S MANUAL BENCH NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION PLEASE READ AND KEEP FOR FUTURE REFERENCE.
OWNER'S MANUAL BENCH MODEL #: NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION PLEASE READ AND KEEP FOR FUTURE REFERENCE. RECEIPT OF PURCHASE: DATE OF PURCHASE: ATTACH HERE UPC CODE:
More informationAgri-Fab OWNERS MANUAL MODEL NO CU. FT. FARM/YARD CART. CAUTION: Read Rules for Safe Operation and Instructions Carefully
Agri-Fab OWNERS MANUAL MODEL NO. 45-01772 CAUTION: Read Rules for Safe Operation and Instructions Carefully 14 CU. FT. FARM/YARD CART Safety Assembly Operation Maintenance Parts the fastest way to purchase
More information! WARNING: FALL HAZARD - To prevent death or serious injury from
pottery barn kids ARMOIRE CHANGING TABLE! WARNING: FALL HAZARD - To prevent death or serious injury from falls, always keep child within arm s reach. Read all instructions before use of the changing table.
More informationO W N E R ' S M A N U A L
TABLE TENNIS TABLE MODEL NOS. T861 T861B O W N E R ' S M A N U A L 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may
More informationIt can be either a 2½ seater bench seat (2 adult and a kid), or a 5 seater picnic table.
Page 1 Folding picnic table in both bench-seat and picnic table mode Introduction Description A single bench seat that can be changed into a picnic table with ease. This 'Bench come Picnic Table' is ideal
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised August 17, 2017 the Roanoke 16'x32' Building w/ full loft Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted
More informationAdirondack Chair BUILD TIME
There are many variations of the classic adirondack chair. This particular version features straightforward construction and common materials. This chair makes for a satisfying project that can be built
More informationFolding Wood Adirondack Chair. Assembly Instructions. Item# S-DN096-C1
Folding Wood Adirondack Chair Assembly Instructions Item# S-DN096-C1 ASSEMBLY INSTRUCTIONS Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish.
More informationM10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5" PH Wood Screws. (30) Included - (24) Required
Door System Unit - Hardware Tools Included: (2) 2mm Allen Wrenches, (2) 3mm Allen Wrenches, (2) 4mm Allen Wrenches, (2) 6mm Allen Wrenches, and (1) 8mm T-Handle Allen Wrench Tools Required: Phillips Screwdriver,
More informationPROJECT PLANS PATIO PLANTER BOX
PROJECT PLNS PTIO PLNTER BOX This great-looking planter makes the perfect place for your favorite plants and flowers. It s sized to hold an 18" round plastic pot, which you can pick up in any garden center.
More information