Greater Vancouver Woodturning Guild
|
|
- Nigel Fletcher
- 6 years ago
- Views:
Transcription
1 Thread Turning Jig Plan By Robert Carlson For the Greater Vancouver Woodturning Guild
2 Thread Turning Jig Mark The following parts list and plans should aid you in creating your own Thread Turning Jig Mark. Some portions of the plans are incomplete like drilling the arbour hole in the front of the slide. This is specific to your particular lathe spindle height. To accomplish this, mount a drill chuck on the lathe spindle with the appropriate sized drill bit (for the arbour shaft) and gently move the completed jig forward along the bed ways into the drill bit. This should give you the appropriate hole placement. It is important to have as little play as possible in the arbour hole and if you have any problems with it you may have to drill it oversized and place a bushing in the hole that is drilled to the correct size. The other consideration is the height of the slide box. This plan will handle lathes with swings from 0 to 8 inches. The slide box sides will have to be extended for lathes with a greater spindle height. Have fun and be safe in the work shop. Robert
3 Thread cutting jig. By Robert Carlson for Hardware & Tools: Part Description Part Number Source Picture Spindle Spindle for holding the chuck 0G0.0 Lee Valley Tools Slide Hold Down /6 x T bolt N/ Pacific Fastener Bolt Bed Hold Down /6 x carriage bolts Home Depot Bolt Locking knob x /6 plastic knob KMS, Lee Valley Tools and Busy Bee Tools T nuts /6 T Nut Lee Valley Tools, Home Depot UHMW Plastic Tools: Jacobs Chuck Plastic for adapters and bushings Drill Chuck either keyed or keyless Off cut pile, Pay cash Redwood Plastics (ldergrove) KMS, Busy Bee Tools, etc. MT/ to JT adapter dapter for mounting the drill chuck in the spindle, must accept a draw bar KMS, Busy Bee Tools See above
4 Part Description Part Number Source Picture Draw bar Threaded rod of appropriate Home Depot, Pacific Fastener size for MT to JT adapter and extend through the headstock spindle Draw bar nut T nut and block Make yourself Fly Cutter /6 llan wrench ground with 60 Degree angle and negative rake angle Make yourself Calipers 6 or 8 dial or digital caliper KMS, Lee Valley Tools, etc. Thread Gauge Thread form gauge Busy Bee Tools Brush Thread cleaning brush Miscellaneous 4
5
6 Bottom Bed Guide Sized to fit specific Lathe TOLERNCES: Thread Turning Jig <INSERT COMPNY HERE>. NY <INSERT COMPNY HERE> IS NEXT SSY PPLICTION TOLERNCING PER: MTERIL DO NOT SCLE DRWING 6 4 " MDF Jig SCLE: : WEIGHT:
7 TOLERNCES: Thread Turning Jig <INSERT COMPNY HERE>. NY <INSERT COMPNY HERE> IS NEXT SSY 4 PPLICTION TOLERNCING PER: MTERIL DO NOT SCLE DRWING 7 " MDF BasePlate SCLE: : WEIGHT:
8 TOLERNCES: Thread Turning Jig <INSERT COMPNY HERE>. NY <INSERT COMPNY HERE> IS NEXT SSY PPLICTION 4 TOLERNCING PER: MTERIL DO NOT SCLE DRWING 8 " MDF Slide SCLE: : WEIGHT:
9 TOLERNCES: Thread Turning Jig <INSERT COMPNY HERE>. NY <INSERT COMPNY HERE> IS NEXT SSY PPLICTION 4 TOLERNCING PER: MTERIL DO NOT SCLE DRWING 9 "MDF Slide Base SCLE: :4 WEIGHT:
10 0.0.0 TOLERNCES: Thred Turning Jig <INSERT COMPNY HERE>. NY <INSERT COMPNY HERE> IS NEXT SSY PPLICTION 4 TOLERNCING PER: MTERIL DO NOT SCLE DRWING 0 " MDF Slide Left SCLE: : WEIGHT:
11 0.0.0 TOLERNCES: Thread Turning Jig <INSERT COMPNY HERE>. NY <INSERT COMPNY HERE> IS NEXT SSY PPLICTION 4 TOLERNCING PER: MTERIL DO NOT SCLE DRWING " MDF Slide Right SCLE: : WEIGHT:
12 .0 TOLERNCES: Thread Turning Jig <INSERT COMPNY HERE>. NY <INSERT COMPNY HERE> IS NEXT SSY PPLICTION 4 TOLERNCING PER: MTERIL DO NOT SCLE DRWING " MDF Slide Back SCLE: : WEIGHT:
13 Drill and Threaded to Master screw dementions Drill Diamiter of rbour shaft /8".00 TOLERNCES: Thread Cutting Jig <INSERT COMPNY HERE>. NY <INSERT COMPNY HERE> IS NEXT SSY PPLICTION TOLERNCING PER: MTERIL DO NOT SCLE DRWING UHMW rbour coupler SCLE: : WEIGHT: 4
This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.
This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4
More informationKnee Mill. 1. Two Axis kits measure the table movement where left to right is considered the X-Axis and front to back is considered the Y-Axis.
Knee Mill Many knee mill manufacturers publish their machine travels in their literature and on their web sites. For new machines, this information is useful to determine the proper length Acu-Rite precision
More informationHOME WORKSHOP HANDBOOK Rugged BENCH GRINDER. By JOEL B. LONG
6 HOME WORKSHOP HANDBOOK Rugged BENCH GRINDER W By JOEL B. LONG ITH this bench grinder you can keep your cutting tools sharp and do general offhand grinding, and can, with the aid of various attachments,
More informationMEAM 150. Fundamentals of Mechanical Prototyping. Introduction Drawings Tolerances. 2009, Jonathan Fiene, University of Pennsylvania
MEM 150 Fundamentals of Mechanical Prototyping Introduction Drawings Tolerances 1 Introduction 2 objectives learn to safely use standard manufacturing tools band saw hand tools drill press lathe mill cnc
More informationPolaris General 1000 EPS 2016
Contact Us: FACTORY UTV LLC. 9237 Beatty Drive Sacramento, CA 95826 Phone : (916) 383-2730 E-mail : info@factoryutv.net Go online: www.factoryutv.net U.H.M.W. Skid Plate / Under Armor Package Ultra. High.
More information20" WOODTURNING LATHE Model 3520A
20" WOODTURNING LATHE Model 3520A Instruction Manual & Parts List M-0460221 (800) 248-0144 www.powermatic.com SPECIFICATIONS: 3520A Lathe Table with standard extensions... 28 x 38 Distance Between Centers...
More informationO-Sullivan King 4 Poster Bed O-Sullivan Queen 4 Poster Bed Parts and Hardware List
Parts and Hardware List A. Left Headboard Post 1 pc B. Right Headboard Post 1 pc C. Left Footboard Post 1 pc D. Right Footboard Post 1 pc E. Headboard Panel 1 pc F. Footboard Rail 1 pc. Spindles 4 pcs
More informationA Portable, Human-Powered Lathe Designed and Built by Scott Lewis Illustrations by David Heim
Tailstock Toolrest and banjo Drive belt guard Headstock post Headstock spindle Page 1 Metric dimensions Tailstock post Drive belt tensioner Drive belt and flywheel Chair Bicycle pedals, sprockets, and
More informationFlush Trimmer Jig By Santanu Lahiri
Flush Trimmer Jig By Santanu Lahiri I found this jig in a book published by the Fine Woodworking people: Ingenious Jigs And Shop Accessories, publisher Taunton Press, ISBN# 1-56158-296-4. The Author is
More informationPrecision made in Germany. As per DIN The heart of a system, versatile and expandable.
1 Precision made in Germany. As per DIN 8606. The heart of a system, versatile and expandable. Main switch with auto-start protection and emergency off. Precision lathe chuck as per DIN 6386 (Ø 100mm).
More informationThis Folding Shelf Kit will work in conjunction with our Swing Away Carrier Kit allowing you add additional exterior storage space to your Vanagon.
Rocky Mountain Westy Folding Shelf Kit Assembly & Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Folding Shelf Kit. We pride ourselves in the products we develop
More informationLegacy Bullet Click Pen Kit
Description: The Bullet Click pen is a step-up kit, with similar features to a Power Click Pen. It has a click mechanism instead of a twist. It uses an 8mm tube and a Parker style gel refill. It is popular
More informationHow To Make A Longworth Chuck OCTOBER 17, 2010
How To Make A Longworth Chuck OCTOBER 17, 2010 Ravenview 27 Comments In The Shop In The Shop, tutorials Need an easy way to finish the bottom of your woodturnings? Tired of continually screwing in and
More informationSECTION 10: PARTS. Headstock
33 32 31 30 7 SECTION 10: PARTS 34 23 36 22 15 14 12 35 37 48 39 41 42 50 40 25 38 38 26 39 42 44 41 25 26 40 51 43 52 10 5 53 9 4 1 27 2 21 19 20 Headstock 8 16 11 17 18 14 13 7 6 45 47 46 3 1 P0768001
More informationTaper Attachment for G4016 Gear Head Lathe
Taper Attachment for Gear Head Lathe MODEL H0775 INSTRUCTION SHEET COPYRIGHT AUGUST, 2004 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE
More informationWOLF LOOM DOUBLE BACK BEAM
WOLF LOOM DOUBLE BACK BEAM Assembly Instructions Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 2017 Schacht Spindle Company,
More informationTools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File. 2. Cut the stock Place stock in vise and cut with hack saw
Purpose: MAKE CATAPULT ARM Step 1 Tools: Sharpie, Square, Vise, Hack saw, Ruler, Punch, Hammer, File Materials: Flat aluminum ½ inch stock (see picture below) Gloves required 1. Pick up the aluminum ½
More informationInstalling CNC Stepper Motor Mounts On A Sherline Lathe
Installing CNC Stepper Motor Mounts On A Sherline Lathe P/N 6720 (6725 Metric) 4000/4100/4500/4600 Lathes P/N 6730 (6735 Metric) 4400/4410 Lathe USING THE TEMPLATE BLOCKS TO LOCATE NEW MOUNTING HOLES FOR
More informationw w w. h d o n l i n e s h o p. d e AUTOMATIC COMPRESSION RELEASE TOOL GENERAL INSTALLATION -J04654 REV Kit Number Models
-J05 REV. 008-0- GENERAL Kit Number 98-08 Models AUTOMATIC COMPRESSION RELEASE TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationUseful accessories for lathe and milling systems.
1 Useful accessories for lathe and milling systems. Nearly all accessories are supplied in wooden boxes. For proper and value preserving storage! Dividing attachment TA 250 For precision lathe PD 250/E,
More informationINSTRUCTIONS FOR HIT LOCK MORTISER
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-200 LOCK MORTISER WHEN USING POWER TOOLS ALWAYS WEAR EYE AND EAR
More informationLegacy Hex Pencil Kit
Description: The Hex pencil is a step-up kit, with similar features to a Slimline Pro Pencil. It has a click mechanism instead of a twist. It uses an 3/8 tube and 2MM pencil lead. It has a heavier feel
More informationMaintenance and Troubleshooting
Mark V This section of the Mark V Owner's Manual contains maintenance information and a troubleshooting guide. It should cover topics and answer most questions you may have for normal maintenance and problem
More informationInstalling CNC Stepper Motor Mounts On A Sherline Mill
Installing CNC Stepper Motor Mounts On A Sherline Mill P/N 6700 (6710 Metric) 5000/5100/5400/5410 Mills P/N 6705 (6715 Metric) 2000/2010 Mills USING THE TEMPLATE BLOCKS TO LOCATE NEW MOUNTING HOLES FOR
More informationIsoBevel Grinder/Sharpener Retrofit Kit for Delta (U.S. Patent 6,381,862)
IsoBevel Grinder/Sharpener Retrofit Kit for Delta 23-700 (U.S. Patent 6,381,862) NOTICE This product is not endorsed by Delta or Tormek and the buyer assumes all risk and liability for its use. In no event
More informationSHOPSMITH SHOP DEPUTY
SHOPSMITH SHOP DEPUTY 556436 Bandsaw/Disc Sander w/ Ext. Table on rough table INTRODUCTION After adding the PowerPro Headstock and the Double-Tilt Base upgrades to your Shopsmith Mark-V, you can use the
More informationHandle Hardware Kit for Router Plane 05P38.10
Handle Hardware Kit for Router Plane 05P38.10 Introduction With this kit, you can make a set of replacement handles for the Veritas Router Plane. The following instructions describe how to make one handle
More informationSECTION 10: PARTS. Headstock
33 32 31 30 7 SECTION 10: PARTS 34 23 36 22 15 14 12 35 37 48 39 41 42 50 40 25 38 38 26 39 42 44 41 25 26 40 51 43 52 10 5 53 9 4 1 27 2 21 19 20 Headstock 8 16 11 17 18 14 13 7 6 45 47 46 3 1 P0768001
More informationAn Adjustable Threading Feed Attachment for a Lathe Without Metric Threading Capability, by Ted Clarke
An Adjustable Threading Feed Attachment for a Lathe Without Metric Threading Capability by Ted Clarke Metric pitch threads, with the exception of the Royal Microscopical Society (RMS) 36 threads per inch
More informationLegacy Woodworking Machinery a division of Phantom Engineering. The Legacy CNC. Assembly Manual
Legacy Woodworking Machinery a division of Phantom Engineering The Legacy CNC Assembly Manual New Orientation of the Legacy Step one: Re-orientation of the machine Remove the X-axis screw and supports.
More informationHow to install/ remove faceplate and hand brakes onto lathes Date Raised: 22 March 2017
Teknatool International Limited 7D Dallan Place, Rosedale, Auckland, New Zealand Tel: +64 09 477 5600 Fax: +64 477 5601 Email: service@teknatool.com Website: www.teknatool.com Frequently Asked Questions
More informationCAB END BEDTRAX (SIDE VIEW)
Supplied Hardware: (8-14) 1/4-20 Allen head bolts, (12-18) UHMW mount blocks, (4) D-ring tie downs Tools Needed: Allen head wrench GET TO IT. INSTALLATION INSTRUCTIONS STEP 1. INSERT (2) MOUNT BLOCKS INTO
More informationDuality Lathe. CNC & Manually Operated Lathe. Product Datasheet.
CNC & Manually Operated Lathe www.tormach.com OVERVIEW The is a revolutionary concept in machine tools. Used in combination with a PCNC 1100 mill, this integrated machine accessory can be operated in three
More informationAssembly. Insert stem and then fix/lock using the grub screw as in picture.
Assembly Parts list: (Boxed set) Body inc hinge plate x1 M33 x 3.5 16 tpi + depth stop collar x1 1 stem + collar x1 HSS cutter x1 Bristol handle x1 Twist handle x1 4mm Allen key x1 3mm Allen key x 1 Instruction
More informationDIY. Inertia Sanders. John Halstad
Inertia Sanders DIY John Halstad Introduction Inertia sanders can help you prepare your turnings for ne nishes, are great for removing tool marks, leveling the nished surface, erasing left over sanding
More informationLegacy Upgraded Junior Gentlemen s Pen Kit
Description: The Upgraded Junior Gentlemen s model is a classic style pen which is easy to turn and uses a Roller Ball Refill which is highly desirable among pen enthusiasts The Upgraded Junior Gentlemen
More informationVacuum System for Woodturnes by Robin Costelle graphics by Caleb Costelle
Vacuum System for Woodturnes by Robin Costelle graphics by Caleb Costelle Have you ever wondered if you need a vacuum system for your woodturning needs? I would answer Yes. A vacuum system is, to me, an
More informationHIT-30 ALUMINUM DOOR SERIES OWNERS MANUAL
HIT-30 ALUMINUM DOOR SERIES OWNERS MANUAL INSTALL LOCKS LATCHES LEVERS / PADDLES INDICATORS STRIKES Every Installation Is A Self-Portrait Of The Person Who Did It! Autograph Your Work With Excellence!
More informationBABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms
BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away
More informationDepending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12
XL Quilting Frame 1 Depending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12 Foot frame Printed 2 June 2014 Updated
More informationAhsanullah University of Science and Technology (AUST) Department of Mechanical and Production Engineering
Ahsanullah University of Science and Technology (AUST) Department of Mechanical and Production Engineering LABORATORY MANUAL For the students of Department of Mechanical and Production Engineering 1 st
More informationPage 1 Parts List for AL-51G (L160) 07/08/201. Headstock Assembly
Page 1 Parts List for AL-51G (L160) 07/08/201 Headstock Assembly 1--------1002-------------------Headstock Casting 13-------1012------------------------------Nut M28 2--------1006---------------------------Flange
More informationMelamine Plastic Laminate. Toilet Partition Installation Manual
Melamine Plastic Laminate Toilet Partition Installation Manual PHONE: FAX: 1-866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL THE
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More informationThe new generation with system accessories. Made in Germany!
1 The new generation with system accessories. Made in Germany! For face, longitudinal and taper turning, thread-cutting. For machining steel, brass, aluminium and plastic. Mounting flange for fastening
More informationDouble Screen Door Installation Instructions
Double Screen Door Installation Instructions (36) #8x1 tek screws (20) #8x1/2 tek screws Package Includes: (2) PCA Screen Doors (1) Astragal (1) Left Hand Z-bar (1) Right Hand Z-bar (1) Header Z-bar (2)
More informationThe new generation with system accessories. Made in Germany!
1 The new generation with system accessories. Made in Germany! For face, longitudinal and taper turning, thread-cutting. For machining steel, brass, aluminium and plastic. Mounting flange for fastening
More information(Fig 1) Column to Base 1. Place Column (7) on the Base (13) and align holes in the Column with holes in the Base. 2. Attach using Bolt Washer and Spring Washer hole through the Column and into the Base.
More information7x --Tailstock Cam Lock
7x --Tailstock Cam Lock By Magic Brian magicbrian40@yahoo.com Probably the most pleasing mod to have, but often not done through lack of milling facility s This version does NOT require a mill. MATERIALS
More informationAgricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationMounting the 6 or 12 Indexer on PRS Gantry Tools
Page 1 Mounting the 6 or 12 Indexer on PRS Gantry Tools About this guide: This document illustrates several options for mounting an indexer onto your ShopBot. You can choose the technique that works best
More informationBLACK HOLE DUST CATCHER Assembly and Installation Instructions
BLACK HOLE DUST CATCHER Assembly and Installation Instructions By: Contents 1. Heavy Duty Aluminum track 1 each 2. Large heavy duty knobs 2 each 3. ¼ x 20 x 1 ¾ T bolts 4 each 4. ¼ x 20 nuts and washers
More informationThe following Instructions are for making an indexed Chuck to create bowls which have 3,4 or 5 equi distance bowls with a possible 6th within.
The Off-Centre Chuck. Ornamental Turners Group Australia th Update 8 June 2010 The following Instructions are for making an indexed Chuck to create bowls which have 3,4 or 5 equi distance bowls with a
More informationDaily Maintenance. 2. Insert bobbin cases in to rotary hooks. Make sure bobbin thread is not over 2 inches long. Close bobbin case covers.
Rotary hook 1. Open bobbin case covers and remove bobbin cases. Use brush to remove lint build up in and around rotary hooks. Compressed air may also be used. Daily Maintenance Cle aning Oiling Rotary
More informationHonda. Pioneer 1000 & U.H.M.W. Skid Plate / Under Armor package. Installation guide
Contact Us: FACTORY UTV LLC. 9237 Beatty Drive Sacramento, CA 95826 Phone : (96) 383-2730 E-mail : info@factoryutv.net Go online: www.factoryutv.net U.H.M.W. Skid Plate / Under Armor package Ultra. High.
More informationUseful enhancements to the Jon Magill rose engine
Useful enhancements to the Jon Magill rose engine Text and photos by Jerry Work copyright 2011, all rights reserved The Dovetail Joint, Kerby, Oregon The Jon Magill designed rose engine is a cleaver adaptation
More informationUSSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS
1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:
More informationA Quick-Change Gearbox For The 7x Minilathe
A Quick-Change Gearbox For The 7x Minilathe Richard Hagenbuch 10 August 2002 This article describes how to a build a quick-change gearbox for your 7X minilathe. I'll describe one that I built as a prototype
More informationTM-1960G - Centre Lathe 480 x 1500mm Turning Capacity - 80mm Spindle Bore Includes Digital Readout
TM-1960G - Centre Lathe 480 x 1500mm Turning Capacity - 80mm Spindle Bore Includes Digital Readout Ex GST Inc GST $23,900.00 $27,485.00 ORDER CODE: MODEL: Swing Over Bed (mm): Distance Between Centres
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More informationRiverside. Oakmont Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 1 pc. 1 pc. 20270 --5/0 Sleigh Headboard 20274 --5/0-6/6 Bed Rails 20273 -- 5/0 Storage Footboard, Panels, Slats Queen
More informationThe Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.
The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box
More informationBy C.W. Woodson From the pages of Model Craftsman magazine June, 1937
By C.W. Woodson From the pages of Model Craftsman magazine June, 1937 As shown in Fig. 1, the tool post grinder for which plans are given here can be used to finish up delicate work to more accurate dimensions
More informationLead Screw Cover Installation
The premier source of tooling, parts, and accessories for bench top machinists. Lead Screw Cover Installation These instructions cover two products: 5201 Telescoping Lead Screw Cover, 7x10, 7x12 5202 Telescoping
More informationOpti-Turn Lathe & Mill Drill Combination Package Deal
Product Brochure K146 OPTIMUM TU-2506V-16M Opti-Turn Lathe & Mill Drill Combination Package Deal 250 x 550mm Page 1 of 7 Front View Lathe Toolpost Removed For Milling Application Left View Without Toolpost
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationFlat Panel Stand FPZ-655. for 32" to 55" Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold
FPZ-655 Flat Panel Stand for 32" to 55" Flat Panel Screens For a viewing experience that really stands out, Peerless FPZ-655 Universal Flat Panel Stand for 32" 55" flat panel TVs provides a brilliant combination
More information7902 Dado Jig. Owners Manual Please Read Carefully! Hardware List: 7902 Parts List:
7902 Dado Jig Owners Manual Please Read Carefully! 7902 Dado Jig Hardware List: Identify and verify that you have all of the hardware shown below prior to assembly. Please read the instructions at least
More informationPRINCESS SINGLE BED WITH TRUNDLE
PRINCESS SINGLE BED WITH TRUNDLE If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale Club Please call our customer service number and have
More informationVARIABLE SPEED WOOD LATHE
MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02
More informationBT500 BT800 MULTI-PURPOSE MACHINE OPERATOR S MANUAL
BT500 BT800 MULTI-PURPOSE MACHINE OPERATOR S MANUAL Many thanks for purchasing our Multi-Purpose Machine. Before operating, Please study the operation manual, and should be according to it to operate step
More informationSETTING UP THE MODEL 210-3, -4, and -5 EQ MT
SETTING UP THE MODEL 210-3, -4, and -5 EQ MT SAFETY PRECAUTIONS FOR THE MODEL 210-3, -4, -5 EQ MT System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting
More informationMI MI OPERATING MANUAL
MODEL NO.: MI-76100 MI-76150 OPERATING MANUAL RULES for SAFE OPERATION MAGNUM INDUSTRIAL MI-76100 and MI 76150 DRILL PRESSES To help ensure safe operation, please take a moment to learn the how to operate
More informationMachining. Module 6: Lathe Setup and Operations. (Part 2) Curriculum Development Unit PREPARED BY. August 2013
Machining Module 6: Lathe Setup and Operations (Part 2) PREPARED BY Curriculum Development Unit August 2013 Applied Technology High Schools, 2013 Module 6: Lathe Setup and Operations (Part 2) Module Objectives
More informationSECTION 9: PARTS. Headstock A 126A 127A-1 REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Headstock 120 121 113 115 112 111 110 109 108 105 106 107 135 101 119A 121 120 118 114 115 107 106 104 123 122 118 114 126A 105 126 103 102 126B 127A-1 131 127A 124 133 134 126C 129 130
More informationLegacy Slimline Pencil Kit
Description: The model is considered one of the most basic pen kits and is a great starter kit for those new to pen turning. Many experienced pen turners use the kit to make elaborate and unusual pens
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationFrom the Original Woodworker s Notebook
From the Original Woodworker s Notebook By Ronald Woodhull VERTICAL MITER FIXTURE A NOTE ON SAFETY Safety is the responsibility of all woodworkers. Do not attempt any project or procedure without all safety
More information(Toll Free); 7am-7pm Pacific Time, Monday-Saturday. Assembly instructions for: MARISSA S ADVENTURE LOFTS
866.332.2403 (Toll Free); 7am-7pm Pacific Time, Monday-Saturday Assembly instructions for: MARISSA S ADVENTURE LOFTS Thank you for purchasing Forever Redwood patio furniture. Forever Redwood is built by
More informationMODEL T TON HYDRAULIC PRESS INSTRUCTIONS (For Machines Mfd. Since 10/17)
MODEL T1241 20-TON HYDRAULIC PRESS INSTRUCTIONS (For Machines Mfd. Since 10/17) For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Identification
More informationReferencing 0,0 position
Page 1 of 11 TITLE: SABRE X-Axis Lead Screw Replacement Procedure Gerber FastFact #: 2013 Supplied by: Gerber Hardware Support Last Modified: March 1, 2011 Summary: The following procedure explains how
More informationPROTECT HOME & FAMILY LOCK IT UP WITH OUR ADVANCED PET DOOR SECURITY COVER INSTALLING YOUR NEW WATCHDOG SECURITY PET DOOR COVER TOOLS NEEDED
PROTECT HOME & FAMILY LOCK IT UP WITH OUR ADVANCED PET DOOR SECURITY COVER INSTALLING YOUR NEW WATCHDOG SECURITY PET DOOR COVER WE ALWAYS RECOMMEND INSTALLING YOUR WATCHDOG SECURITY PET DOOR COVER ON THE
More informationINSTALLATION GUIDE. C20-FTL STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel )
INSTALLATION GUIDE C20-FTL STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Partition Assembly... 3-5 5-6 Phase 2 -
More informationBHJ Products, Inc. Parts List & Instructions
Product Name: O-Ring Groove Cutter Page 1 of 6 Kit Contents: 1x Cutter Head Assembly with Handle & Adjustable Tool Block 1x Graduated Adjusting Screw 1x Adjustable Tool Holder 1x Carbide Insert (Size of
More informationDIY Lowery Inspired Embroidery Floor Stand
DIY Lowery Inspired Embroidery Floor Stand Below find the details on how to build your own embroidery floor stand. The Lowery Floor Stand inspired this design. Note using the following instructions will
More informationThe premier source of parts and accessories for mini lathes and mini mills. Mini Lathe User s Guide. from LittleMachineShop.com
The premier source of parts and accessories for mini lathes and mini mills. Mini Lathe User s Guide from LittleMachineShop.com Copyright 2002, LittleMachineShop.com All rights reserved. Some photos Copyright
More informationDrilling. Drilling is the operation of producing circular hole in the work-piece by using a rotating cutter called DRILL.
Drilling Drilling is the operation of producing circular hole in the work-piece by using a rotating cutter called DRILL. The machine used for drilling is called drilling machine. The drilling operation
More informationLOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page
LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit
More informationSECTION 9: PARTS. Electrical Box. (0000 Series Parts) 0000 Series Parts List
SECTION 9: PARTS Electrical Box (0000 Series Parts) 0000 Series Parts List 1 P04920001 CONTACTOR 6 P04920006 FUSE 2A (LC1-D0910, B5, 24V, 50HZ) 7 P04920007 FUSE HOUSING 2 P04920002 CONTACTOR 8 P04920008
More informationVARIABLE SPEED WOOD LATHE. Model DB900 INSTRUCTION MANUAL
VARIABLE SPEED WOOD LATHE Model DB900 INSTRUCTION MANUAL 1007 TABLE OF CONTENTS SECTION...PAGE Technical data.. 1 General safety rules....1-3 Specific safety rules for wood lathe.....3 Electrical information.4
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationYardistry. External Display YP *Time required for assembly approximately 1.5-2hrs
Yardistry External Display YP40030 *Time required for assembly approximately 1.5-2hrs Components 4 Packages of Panel Clips (Includes 6 Panel Clips and Hardware) 3 16 1/2 x 16 1/2 Signs (hardware Included)
More informationGrizzly Drill Press SOP
Grizzly Drill Press SOP Drill Press is wired to run on 0V. Drill Press has a built in light with a ON/OFF switch. Never hold a workpiece by hand while drilling. Clamp it down or hold it in a vice. Never
More informationPARTS G9729 Lathe Bed
PARTS G9729 Lathe Bed 114 132 126 125 131 133 129 128 130 127 139 124 10 124 123 122 135 137 147 144 121 148 146 149 136 138 140 150 152 142 143 141 151 153 21 168 20 19 18 17 162 22 147 13315 14 13131
More informationadaptivemechanical adaptive
Mechanical clamping elements mechanical 6 Content Product group 6 Sliding clamp, mechanical 6.2210 Clamping block, mechanical 6.2212 High-pressure spindle, mechanical with integral wedge system 6.2270
More informationSentinel Electronic Safe Installation Guide
Sentinel Electronic Safe Installation Guide by Rev 07/12/2004 P/N 100020 Table of Contents 1. OVERVIEW...3 2. SAFE INSTALLATION...3 2.1. TOOLS REQUIRED...3 2.2. SELECTING THE MOUNTING LOCATION...3 2.3.
More informationKELTON CARVING JIG Guide for Use
KELTON CARVING JIG Guide for Use The Kelton Carving Jig has been designed to securely hold a work piece at the desired angle and working height. While it will greatly benefit wood tuners and carvers, its
More informationIDR assembly instructions:
IDR assembly instructions: Required Tools: 2 X 12mm Open End Wrench 14mm open end wrench #2 Phillips Head Screw Driver (Drill with adjustable torque clutch recommended) 8mm nut driver (Supplied in IDR-AK)
More informationBHJ Products, Inc. Parts List & Instructions
Product Name: Lifter-Tru Kit for Ford Windsor & SVO Small Block V8 Page 1 of 5 Kit Contents: 2x End Plates 2x 5/8 Threaded Adjustment Sleeves 1x Front Angle Bracket 2x 5/8 Adjustment Sleeve Spacers * 1x
More information