BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms

Size: px
Start display at page:

Download "BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms"

Transcription

1 BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away the carton or any of the packing material until you have checked to see that all of the parts and hardware have been received All hardware is sized in inches. Illustrations of the various hardware and an inch scale are provided to aid you in determining the correct piece of hardware to use. Before starting the assembly, read the instructions completely and familiarize yourself with the drawings and parts. Follow the exact order of assembly. Take care and work slowly. If you have someone to help you, the assembly will be easier. The wood parts have a removable label on them to identify each part. We recommend that you leave the labels in place until the loom is fully assembled. When you finish assembling the Wolf loom, go back over all of the screws and make sure they are tight. It is a good idea to re-tighten the screws every few months. Remember not to tighten those screws and bolts which are supposed to allow their parts to pivot. All wooden parts of the loom have been finely sanded and finished with hand-rubbed Danish oil. From time to time you may wish to apply more finish to the loom. Use a Danish oil (tung oil and polyurethane mixture) and hand rub the wood with a soft, lint-free cloth. Be sure to follow all the manufacturer s instructions. TOOLS #2 Phillips screwdriver 5/16" or adjustable wrench Flat screwdriver HARDWARE LIST Note: Parts pictures are not to scale. Listed part quantities are what is needed for assembly. There may be extras of some parts. Parts may not be pictured in every listed size. HARDWARE BAG A STEPS Fold bars 4 3/16" x 1-1/4" carriage bolts 4 3/16" lock nuts 8 3/16" washers 2 1/4" washers 2 5/16" lock nuts 2 Black knobs w/ 1" threaded shaft 2 Plastic bearings HARDWARE BAG B STEPS /4" x 2" machine screws 6 1/4" barrel nuts 1 Ratchet advance lever 2 3/8" USS washers 4 #8 x 1-1/2" screws 1-1/4" carriage bolt 1-1/2" machine screw 2" machine screw 2-1/2" carriage bolt 1-1/2" screw Ratchet advance lever assembly Knob w/ 1" shaft Plastic bearing Wing nut Barrel nut Lock nut from top Lock nut Slim lock nut Fold bar Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO p f Schacht Spindle Company, Inc

2 HARDWARE BAG C - STEPS /4" x 2" machine screws 4 1/4" barrel nuts 2 #8 x 1-1/2" screws 2 1/4" x 2-1/2" carriage bolts 4 1/4" washers 2 1/4" wing nuts 2 5/16" slim lock nuts HARDWARE BAG D - STEPS Jack pivot rods 2 1/4" washers 2 1/4" lock nuts 4 1-1/2" screws Jack pivot rod O-ring Hex nut Brake S-hook Brake peg Brake barrel nut 0 ⅛ ¼ ⅜ ½ ¾ 1 1½ 1¾ 2 2¼ 2½ 4-shaft: 2 4-1/2" carriage bolts 14 3/8" SAE washers 8-shaft: 2 7" carriage bolts 22 3/8" SAE washers 4 Now/4 Later: 2 7 carriage bolts 14 3/8 SAE washers 6 - nylon Jack spacers Brake spring Brake eyebolt Brake cord 3 4 HARDWARE BAG E - STEPS /4" barrel nuts 2 #8 x 1-1/2" screws 4-shaft and 4 Now/4 Later: 7 hex nuts 7 O-rings 8-shaft: 11 hex nuts 11 O-rings Note: There may be extra hex nuts and O-rings. HARDWARE BAG F - STEP 17 (Not included with 4-Shaft Looms) 2 #8 x 1-1/4" screws 10 Treadle aid(elastic) cords Brake bar and cable Cap nut Warp beam crank handle HARDWARE BAG G - STEP /8" USS washers 1 Brake barrel nut (long) 1 1/4" x 1" machine screw 3 1/4" washers 3/16" 1 Brake bar and cable 1/4" Treadle Aid cords 1 5/16" slim lock nut 1 Brake S-hook 1 Plastic brake peg 1 Texsolv brake cord 1 Brake eye bolt 1 Brake spring with insert 1 3/16" washer 3/8" SAE 1 Warp beam crank handle 1/4 fender 3/8" USS 1 3/8" cap nut 1 3/8" washer Note: Washer sizes are measured by the diameter of the hole. 3/8" USS washers have a larger outside diameter than 3/8" SAE washers

3 HARDWARE BAG H - STEP /4" barrel nuts 2 Fender washers 2 Black knobs with 2-1/4" threaded shaft 1 Beater pin and chain 1 Beater pin holder 1 #6 x 5/8" screw Beater pin holder Beater pin and chain HARDWARE BAG I - STEP Texsolv apron cords 4-shaft: 24 tie-up cords 8-shaft and 4 now/4 Later: 80 tie-up cords 5/8" screw Apron cords Tie-up cords Black knob w/ 2-1/4" shaft heddle bar beater top harness or shaft heddle bar hook beater race beater stop castle side left right upper castle support left beater side front oval beam rear oval beam rear beam knob reed rear or warp beam Click here for Wolf Loom Brake Parts front beam extension warp crank assembly outside leg - left left front beam support front or cloth beam right beater side brake pedal cord texsolv 1.75 ft. fold knob metal fold bar jacks front castle cross beater support lamms tie-up cords RPFL95 treadles beater pin inside leg - left treadle block brake pedal treadle support bar serial number ratchet dog ratchet gear treadle spacer right front beam support rear leg brace inside leg - right ratchet advance lever outside legright

4 ASSEMBLY INSTRUCTIONS fold bars 1. Attach the fold bars to the legs. Parts: two pairs of legs, 4 fold bars, 4 3/16" x 1-1/4" carriage bolts, 8 3/16" washers, 8 3/16" lock nuts. On the outside legs, the fold bar is installed on the side of the leg that faces the inside of the loom, in the upper hole. On the inside legs, the bar is installed on the side of the leg that faces the outside of the loom. Make sure to orient the fold bars as shown in figure 1. 3/16" lock nut 3/16" washer 1-1/4" carriage bolt square hole in fold bar Insert the carriage bolt into the square hole on the fold bar. Align the square part of the carriage bolt just under the head of the bolt with the square hole in the fold bar. Place a washer on the bolt, insert the bolt into the leg, place another washer on the bolt, and secure with a lock nut. Repeat this process for all legs. use the upper hole on the outside legs inside right leg outside right leg Figure 1 - ATTACH FOLD BARS TO RIGHT INSIDE AND OUTSIDE LEGS leg fold bar 3/16" lock nut 1-1/4" carriage bolt 3/16" washer 3/16" washer FIGURE 1A - HARDWARE TO ATTACH THE FOLD BARS left castle side right castle side 2. Attach the castle sides to the legs. Parts: the two castle sides, 2 1/4" washers and 2 5/16" lock nuts. Place the legs so that the bolt holding the legs together is extending upwards. Put the bolt through the hole in the castle side, place a washer on the bolt, and secure with a 5/16" lock nut. insert bolt in legs through hole in castle sides left legs right legs Figure 2 - ATTACH CASTLE SIDES TO LEGS - 4 -

5 3. Attach the fold bars to the castle. Parts: 2 plastic bearings, 2 black knobs with 1" threaded shaft. Flip the legs/castle side assemblies so they are lying with the slot in the castle side facing up. front of loom right castle side top of right castle side Tip the castle side so that the metal nut inside the slot is in the middle of the slot in the castle side. Put the plastic bearing in the slot over the screw hole in the metal nut. Place the ends of the fold bars over the plastic slide, first the front bar, then the rear bar. Insert a fold knob through the bars and plastic slide, and screw it into the metal nut. Slide the knob to the bottom of the slot, opening the legs as far as they will go, and tighten the knob. Repeat for the other side. Note: The fold bars must be assembled (stacked) in the order shown in figure 3. metal nut fold knob front fold bar Figure 3 - ATTACH THE FOLD BARS TO THE CASTLE SIDES rear fold bar plastic bearing metal nut 4. Attach the treadle assembly to the legs. Parts: treadle assembly, 2 1/4" x 2" machine screws, 2 1/4" barrel nuts. Remove any tape from the ends of the treadle bar. Orient the treadle assembly with the brake pedal at the right side of the loom. Line up the pins at the end of the treadle support with the small holes on the inside of the legs, and the treadle bar with the 3/8" hole in the legs. Insert a 2" machine screw into each leg from the outside. From underneath the treadle support, place a barrel nut into the hole on each end of the treadle support. Tighten the screws firmly into the barrel nuts. treadle bar brake pedal treadle support hole for machine screw 2" machine screw treadle support hole for treadle support pin treadle support pin barrel nut inside treadle support Figure 4 - ATTACH THE TREADLE ASSEMBLY 5. Install the rear leg brace. Parts: Rear leg brace, 2 1/4" x 2" machine screws, 2 barrel nuts. 2" machine screw Insert a barrel nut in the hole at the end of the rear leg brace and secure with a 2" machine screw inserted though the hole drilled in the bottom of the outside legs. Repeat for the other end. barrel nut rear leg brace Figure 5 - INSTALL THE REAR LEG BRACE barrel nut 2" machine screw - 5 -

6 6. Install the cloth beam and ratchet advance lever. Parts: cloth beam, ratchet advance lever, 2 3/8" USS washers. cloth beam Place the ratchet advance lever on the axle of the cloth beam, next to the ratchet gear. Place a washer on each end of the cloth beam. Insert the cloth beam in the holes in the cloth beam supports. cloth beam support cloth beam support ratchet advance lever 3/8" washer cloth beam support ratchet advance lever ratchet gear Figure 6 - INSTALL THE CLOTH BEAM AND RATCHET ADVANCE LEVER 7. Attach the front castle cross brace. Parts: front castle cross brace, 4 #8 x 1-1/2" screws. Attach the front castle cross brace to the front edge of the castle sides, using a screw at each corner of the brace. The square holes should be at the top of the brace, and the logo should face front and be right side up. logo front castle cross brace Figure 7 - INSTALL FRONT CASTLE CROSS BRACE 8. Attach the front beam. Parts: front beam with attached extension, 2 1/4" x 2" machine screws, 2 1/4" barrel nuts. front beam The front beam should be oriented between the tops of the outside legs, with the extension to the front and angled down. Hold a barrel nut in the hole at one end of the front beam. Insert a screw through the leg from the outside-in and into the barrel nut in the front beam. Figure 8 - INSTALL FRONT BEAM WITH EXTENSION front beam extension - 6 -

7 9. Assemble the beater. Parts: Beater sides, beater top, beater race, 2 1/4" x 2" machine screws, 4 1/4" barrel nuts, 2 #8 x 1-1/2" machine screws, 2 1/4 x 2-1/2" carriage bolts, 2 1/4" washers, 2 1/4" wing nuts. 1/4" x 2-1/2" carriage bolt Attach the beater side to the beater race. Put a #8 x 1-1/2" screw through the front hole of the beater side. Insert a barrel nut into the front hole on the bottom of the beater race and secure with the screw. Repeat for the back hole, using a 1/4" x 2" machine screw and a barrel nut. wing nut washer slot for carriage bolt beater top reed Attach the beater top to the sides. On each end of the beater top, put a 1/4" x 2-1/2" carriage bolt through the beater top from the back. If you wish, you can put the reed in the beater at this point. Set the beater top down on the sides, turning the carriage bolts to fit the square part of the bolts into the slots on the beater sides. Secure with washers and wing nuts. 1/4" x 2" machine screw #8 x 1-1/2" machine screw left beater side barrel nut beater race Figure 9 - ASSEMBLE THE BEATER Install the beater assembly. Parts: Beater assembly, 2 5/16" slim lock nuts. With the beater race facing the front of the loom, place the metal ends of the beater sides onto the bolts pre-installed on the inside legs. Secure the beater with a slim lock nut on each bolt. Tighten the lock nuts all the way, then loosen 1/2 to a full turn to allow the beater to move freely. pre-installed bolt and lock nut 5/16" slim lock nut metal part of beater side Figure 10 - INSTALL THE BEATER ASSEMBLY - 7 -

8 10. Install the jacks and lamms. Parts: 2 jack pivot rods. For 4-shaft looms: 14 3/8" SAE washers, 2 #1 jack assemblies, 2 #3 jack assemblies. For 8-shaft looms: 22 3/8" SAE washers, 2 #1 jack assemblies, 2 #2 jack assemblies, 2 #3 jack assemblies, 2 #4 jack assemblies. For 4 Now 4 Later looms: 14 3/8 SAE washers, 2 #1 jack assemblies, 2 #2 jack assemblies, 6 -- nylon jack spacers From the rear of the loom, insert the two aluminum jack pivot rods into the larger holes of the front castle cross brace. Place two washers on each of the rods. (Figure 11-A) 4-Shaft Looms: Place a #1 jack assembly on the pivot rods. Place a 3/8" washer on each rod, followed by the second #1 jack assembly. Continue with another washer on each rod, a #3 jack assembly, another washer, and the second #3 jack assembly. Finish by placing two more 3/8" washers on each rod. (Figure 11-B & 11-C) 8-Shaft looms: Place a #1 jack assembly on the rods. Place a 3/8" washer on each rod, followed by a second #1 jack assembly. Continue in the following order: a washer on each rod, a #2 jack assembly, a washer, the second #2 jack assembly, and a washer. Continue with a #3 jack assembly, washers, the second #3 jack assembly, washers, a #4 jack assembly, washers, and the second #4 jack assembly. Finish by placing two 3/8" washers on each rod. (Figure 11-B & 11-C) 4 Now 4 Later looms: Place /8" washers on each jack pivot rod and then place a #1 jack assembly on the pivot rods. Place /8" washer on each rod followed by the second #1 jack assembly on the pivot rods. Continue with another washer on each rod, then a #2 jack assembly on the pivot rods, another washer on each rod, and then the last #2 jack assembly on the pivot rods. Finish by placing 2 more 3/8" washers on each pivot rod followed by 3 nylon jack spacers on each pivot rod. jack pivot rods A B C Figure 11 - INSTALL THE JACK ASSEMBLIES two washers on each rod back side of front castle cross brace #1 jack assembly one washer on each rod #1 jack assembly #3 jack assembly two washers on each rod 1-1/2" machine screw rear castle cross brace 11. Install the rear castle cross brace. Parts: Rear castle cross brace, 4 1-1/2" screws. Using 2 screws at each end, attach the rear castle cross brace to the castle. Figure 12 - INSTALL THE REAR CASTLE CROSS BRACE 1-1/2" machine screw - 8 -

9 12. Install the carriage bolts. Parts: 2 1/4" x 4-1/2" carriage bolts for 4-shaft or 2 1/4" x 7" carriage bolts for 4 Now/4 Later and 8-shaft; 2 1/4" lock nuts for all looms Push the jacks down in the center and insert the carriage bolts (4-1/2" for 4-shaft, 7" for 4 Now/4 Later and 8-shaft) through holes in the front castle cross brace and on through the holes in the rear castle cross braces. Align the square part of the carriage bolts in the square holes and tap them firmly into the holes. Put a washer on each bolt and secure with a 1/4" lock nut. Do not tighten the lock nut all the way. The washer should remain loose. carriage bolts Figure 13 - CARRIAGE BOLTS & CASTLE CROSS BRACES front castle cross brace rear castle cross brace 13. Install heddles on the shafts. Parts: For 4-shaft looms: 4 shafts, 8 heddle bars, 400 heddles. For 4 Now/4 Later loom: 4 shafts, 8 heddle bars, 800 heddles For 8-shaft looms: 8 shafts, 16 heddle bars, 800 heddles. Note: The heddle bar hooks in each shaft are slightly off-center. The hooks should all be lined up when the shafts are installed in the loom. slide lock shaft frame heddle bar hook heddle bar Figure 14 - PUSH UP ON THE SLIDE LOCK Lay a shaft on a flat surface. Push up on the slide lock on the heddle bar hook and pull the heddle bar out of the hook. Release the slide lock. Flex the heddle bars enough to remove one end from the slot in the side of the shaft frame. Remove the bars from the frame. Lay the heddle bars next to the heddles. Carefully slide a group of heddles onto the heddle bars. Keep the heddles loosely tied until the heddle bars are installed in the shaft frame. Be sure to keep the heddles oriented in the same direction for easier threading. Replace the heddle bars in the shaft frame. Insert one end of each heddle bar in the slot in the frame. Flex the heddle bar and insert the other end into its slot. Divide the heddles approximately in half and push them to either end of the heddle bar. Push up on the slide lock and place the heddle bar back on the hooks. Put the shaft back in the loom, and secure the jack pin with the hex nut. shaft frame heddle bar Figure 14 B - FLEX THE HEDDLE BAR AND PULL OUT heddle bar Figure 14 C - SLIDE HEDDLES ONTO THE HEDDLE BAR Repeat for the other shafts. Note: This process is covered in the video Assembling the Baby Wolf Loom. You can find the video at youtube.com/ user/schachtspindle. Figure 14 D - HEDDLES INSTALLED ON SHAFT - 9 -

10 14. Insert the shafts into the castle. Parts: For 4-shaft looms: 4 small hex nuts, 4 small O-rings. For 8-shaft looms: 8 small hex nuts, 8 small O-rings. Slide a harness frame into the front channel in the castle sides. Insert the jack pin into the hole in the center of the bottom of the frame. Secure the jack pin with a hex nut, then push a small O-ring on top of each hex nut. As you insert the rest of the harnesses, keep them oriented so that the heddle bar hooks are lined up. heddle bar heddle bar hook hex nut with O-ring on top jack pin (inside frame) harness frame Note: This process is covered in the video Assembling the Baby Wolf Loom. You can find the video at youtube.com/ user/schachtspindle. 15. Install the upper rear castle cross brace. Parts: Upper rear castle cross brace, 2 #8 x 1-1/2 screws. Orient the brace with the logo right side up. Attach the rear upper castle cross brace to the castle with a 1-1/2" screw at each end of the brace. Figure 15 - SECURE THE JACK PINS upper rear castle cross brace 1-1/2" screw 1-1/2" screw rear castle cross brace Install the Treadle Aid (8-Shaft and 4Now/4Later Looms only). Parts: 2 #8 x 1-1/4" screws, 1 1/4" dowel, 10 treadle aid cords. Attach the treadle aid bar to the rear castle cross brace with a 1-1/4" screw at each end. To set up the treadle aid, start at one end of the treadle aid bar and push a treadle aid cord up through one of the holes (an opened paper clip can be most helpful with this step) and then over the 1/4" dowel. Continue across the entire treadle aid bar. You will attach the treadle aid cords to the ends of the treadles in the same manner as you will attach the tie-up cords that control the lamms (instruction 26). We recommend using a treadle aid cord on all of the treadles. Figure 16 - INSTALL THE UPPER REAR CASTLE CROSS BRACE rear castle cross brace 1/4" dowel treadle aid bar Figure 17 - INSTALL THE TREADLE AID 1-1/4" screw treadle aid cord 16. Install the warp beam. Parts: Warp beam, 2 3/8" USS washers. Take the warp beam and place a 3/8" USS washer on each end. Slip the threaded rod through the hole in the inside right leg as far as it will go. Fit the pin in the other end into the stopped hole in the inside leg - this hole does not go all the way through the leg. You will have to spread the right and left inside legs apart to accomplish this. threaded pin through hole in leg Figure 18 - INSTALL THE WARP BEAM short pin into stopped hole in leg

11 17. Install the brake barrel nut. Parts: 1 1/4" x 1" machine screw, 1 long brake barrel nut. From the outside of the inside right leg, push the screw through the leg, and tighten into the brake barrel nut. 18. Install the brake bar and brake cable. Parts: 2 1/4" washers, 1 slim 5/16" lock nut. inside right leg (outside view) 1" screw brake barrel nut Figure 19 - INSTALL THE BRAKE BARREL NUT inside right leg (inside view) Remove any packing material attached to the screw installed on the inside right leg. pre-installed screw with packing material Put the brake bar and a 1/4" washer on the screw. Take the loose end of the brake cable attached to the brake bar and wrap it under and around the brake drum. Start next to the loom leg and wrap with loops moving towards the loom center, making sure not to overlap the cable. Place the loop end of the cable over the pre-installed screw. Secure with another 1/4" washer and a slim 5/16" lock nut. Be sure that the brake bar can pivot freely. If it does not, slightly loosen the lock nut. 19. Install the brake cord. Parts: 1 brake peg, 1 S-hook, Texsolv brake cord. Attach the S-hook to the hole on the rear of the brake bar. Loop the Texsolv brake cord through the S-hook on the brake cable bar. Slip the other end of the cord through the hole at the end of the brake pedal. Secure the brake cord by inserting the brake peg into the 5th or 6th loop from the end of the brake cord. brake bar, 1/4" washer, loop end of brake cable, 1/4" washer, slim 5/16" lock nut on pre-installed screw brake bar brake bar on pre-installed screw brake drum brake cable (hanging loose) Figure 20 - INSTALL BRAKE BAR AND BRAKE CABLE 20. Install the brake eyebolt and brake spring. Parts: 1 eyebolt, 1 brake spring, 1 3/16" washer Figure 21 - INSTALL BRAKE CORD S-hook brake cord brake pedal Attach the brake spring to the brake bar. Insert the eyebolt through a 3/16" washer, through the hole in the long barrel nut, and screw it into the spring. Tighten the eyebolt until you can t turn the warp beam away from you when you twist the beam with both hands. When you hold the brake release pedal down, the warp beam should turn freely in either direction. brake eyebolt washer brake spring brake peg By tightening or loosening the eye bolt, you can increase or decrease the tension on the friction brake. There should be small gaps between the coils of the brake spring once the proper tension is reached brake bar Figure 22 - INSTALL BRAKE EYEBOLT AND BRAKE SPRING

12 21. Install the warp beam crank handle. Parts: 1 warp beam crank handle, 1 3/8" washer, 1 3/8" cap nut. Place the 3/8" washer and then the metal crank handle on the threaded shaft extending through the leg from the brake end of the warp beam. The wood crank handle faces away from the loom. Secure with the 3/8" cap nut. Tighten the nut by placing the handle over it and turning clockwise. To engage the crank for turning the warp beam, pull the hexagonal hole in the crank onto the cap nut. While weaving, the crank should be pushed off the cap nut. cap nut warp beam crank handle 3/8" washer threaded shaft Figure 23 - INSTALL THE WARP BEAM CRANK HANDLE 22. Install the removable back beam. Parts: Back beam, 2 1/4" black knobs, 2 fender washers, 2 1/4" barrel nuts. fender washer back beam Slide the back beam into the slots cut in the top of the inside legs. Put a fender washer on a knob, and insert the knob through the leg, into the back beam, and tighten it into a barrel nut in the back beam. Repeat for the other side. black knob barrel nut Inside left leg Figure 24 - INSTALL THE REMOVABLE BACK BEAM 23. Install the beater pin. Parts: Beater pin with chain, beater pin holder, 1 #6 x 1/2" screw. Put the screw through the hole in the end of the beater pin chain and through the hole in the beater pin holder. Fasten it to the small pilot hole in the right leg. There will be a hole between the pilot hole and the screw holding the fold support bar. beater pin holder 1/2" screw beater pin beater pin chain fold support bar slot in beater side The beater pin is used to hold the beater upright during warping. Push the pin through the hole in the leg and then through the slot in the beater side. Remember to pull the beater pin out and replace it in its holder before weaving or folding the loom. hole for beater pin to hold the beater upright beater pin and holder Figure 25 - INSTALL THE BEATER PIN HOLDER

13 24. Install the tie-ups on the lamms. Parts: For 4-shaft looms: 24 tie-ups For 8-shaft and 4 now/4 Later looms: 80 tie-ups Push the loop end of a tie-up through each hole in the lamms. Put the button end of the tie-up through the loop and pull tight. To attach a shaft to a treadle, slide the button end of the tie-up into the slot in the treadle. Make sure the tie-up hangs straight down to the treadle. end of treadle (rear) tie-up lamm Note: This process is covered in the video Assembling the Baby Wolf Loom. You can find the video at youtube.com/ user/schachtspindle. button Figure 26 - INSTALL THE TIE-UPS ON THE LAMMS 25. Install the apron bars. Parts: 2 apron bars, 10 Texsolv apron cords Insert one end of a cord through a hole in the cloth beam and pull the cord through. Then insert the other end through the second hole in the end of the cord that you just put through the beam. Pull firmly on the cord to tighten (A). Repeat across the cloth beam and the warp beam. To attach the apron bar to the apron cords, take a pinch of the cord about 4" from the end (B). Insert the pinched cord through the second hole in the cord. Pull on the pinched cord until a new loop forms that is large enough for the apron bar to slip through (C). Slide the apron bar through the loop (D) and pull tight. Repeat until all cords are attached to the apron bar. Attach the other apron bar to its beam in the same way. A B C D E Figure 27 - INSTALL THE APRON BARS Note: This process is covered in the video Assembling the Baby Wolf Loom. You can find the video at youtube.com/ user/schachtspindle. FOLDING THE LOOM To prevent treadles from dragging on the floor when the loom is folded, attach every treadle to at least one tie-up cord. Loosen the two black fold knobs one full turn and pull them up to start folding the loom. With one hand on the rear beam and one hand on the front beam, pull the loom together as far as it will go. Tighten the knobs. Push the slide lock bars in towards the front of the loom. slide lock bar UNFOLDING THE LOOM Slightly loosen the two black fold knobs on both sides of the loom. Generally, a single turn will do. Note: Loosening the knobs all the way or removing them can cause the loom to collapse which could result in injury. Stand at the side of the loom. Hold the front and rear beams together slightly, and pull the slide lock bars out toward the back of the loom. Continue holding onto the front and rear beams and allow the loom to unfold all the way. If there is a warp on the loom, step on the brake release pedal while unfolding the loom to loosen the warp. When the loom is all the way down in the open position, push the fold knobs to the bottom of the slots and tighten them

WOLF PUP LOOM TM & WOLF PUP LT LOOM TM

WOLF PUP LOOM TM & WOLF PUP LT LOOM TM WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212

More information

SCHACHT STANDARD FLOOR LOOMTM

SCHACHT STANDARD FLOOR LOOMTM SCHACHT STANDARD FLOOR LOOMTM FL3109 FL3111 FL3113 FL3115 FL3121 FL3123 FL3125 FL3127 FL3310 FL3312 FL3314 FL3316 FL3322 FL3324 FL3326 FL3328 Assembly instructions LOW CASTLE LOOM IN MAPLE Find out more

More information

WOLF LOOM DOUBLE BACK BEAM

WOLF LOOM DOUBLE BACK BEAM WOLF LOOM DOUBLE BACK BEAM Assembly Instructions Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 2017 Schacht Spindle Company,

More information

COLONIAL I 4s, 8s &12s Jack type

COLONIAL I 4s, 8s &12s Jack type COLONIAL I 4s, 8s &12s Jack type 45" 60" 4s 1051-0000 1052-0000 8s 1051-0008 1052-0008 12s 1051-0012 1052-0012 On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing

More information

CRANBROOK LOOM. Assembly manual

CRANBROOK LOOM. Assembly manual CRANBROOK LOOM Assembly manual Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 2015 Schacht Spindle Company, Inc. 01.15 4- AND

More information

NILUS II 8 SHAFTS JACK-TYPE LOOM

NILUS II 8 SHAFTS JACK-TYPE LOOM NILUS II 8 SHAFTS JACK-TYPE LOOM 36" 45" 60" 8 SHAFTS 1029-0008 1030-0008 1031-0008 On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing material until all parts are

More information

NILUS II COUNTER-BALANCED

NILUS II COUNTER-BALANCED NILUS II COUNTER-BALANCED 36" 45" 60" 1026-0000 1027-0000 1028-0000 On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing material until all parts are inventoried. Check

More information

COMPACT 24 4 SHAFTS Savoie C. P. 4 Plessisville, Qc. G6L 2Y6

COMPACT 24 4 SHAFTS Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 COMPACT 24 4 SHAFTS 1022-0000 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the loom, unpack and lay out the

More information

COMPACT 24 8 SHAFTS

COMPACT 24 8 SHAFTS COMPACT 24 8 SHAFTS 1022-0001 1573 Savoie C. P. 4 Plessisville, Qc. Canada G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the loom, unpack and lay out

More information

Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO p f

Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO p f WOLF STROLLER FL3051 Assembly Instructions folded ready to travel open ready to weave For installation on Wolf Pup, Wolf Pup LT, Baby Wolf, and Mighty Wolf Looms Find out more at schachtspindle.com Schacht

More information

ARTISAT 36 JACK-TYPE 8 SHAFTS

ARTISAT 36 JACK-TYPE 8 SHAFTS ARTISAT 36 JACK-TYPE 8 SHAFTS 1009-0008 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the loom, unpack and lay

More information

COMPACT 24 8 SHAFTS

COMPACT 24 8 SHAFTS COMPACT 24 8 SHAFTS 1022-0001 1573 Savoie C. P. 4 Plessisville, Qc. Canada G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com nfo@leclerclooms.com On receiving the loom, unpack and lay out

More information

Spring. Instructions for assembly

Spring. Instructions for assembly Spring Instructions for assembly The parallel countermarch system... 1 Spring assembly tips and information... 3 Assembly of the Spring... 5 Maintenance... 17 Version: Spring-V5 The parallel countermarch

More information

FLOOR LOOM & WOLF LOOMS

FLOOR LOOM & WOLF LOOMS FLOOR LOOM & WOLF LOOMS Maintenance & Warranty 36 Standard Floor Loom Baby Wolf Wolf Pup 8.10 Wolf Pup Wolf Pup LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO

More information

8 SHAFT KIT FOR NILUS II WITH BACK HINGE TREADLES

8 SHAFT KIT FOR NILUS II WITH BACK HINGE TREADLES 8 SHAFT KIT FOR NILUS II WITH BACK HINGE TREADLES 36" 45" 60" 1029-2836 1030-2845 1031-2860 On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing material until all

More information

AUTOMATIC ADVANCE MANUAL

AUTOMATIC ADVANCE MANUAL AUTOMATIC ADVANCE MANUAL AVL Looms, Inc. 3851 Morrow Lane, Suite #9 Chico, CA 95928-8305 530 893-4915 530 893-1372 fax # info@avlusa.com www.avlusa.com Copyright 2009 TABLE OF CONTENTS Page # I. Parts.........................

More information

FLIP RIGID HEDDLE LOOM

FLIP RIGID HEDDLE LOOM FLIP RIGID HEDDLE LOOM SL2013, SL2014 SL2015, SL2016 Warping and Weaving Instructions Flip Loom shown with optional accessories Trestle Floor Stand and Flip Trap Find out more at schachtspindle.com Schacht

More information

ASHFORD TABLE LOOM - EIGHT SHAFT 410/610/800mm 16/24/32in

ASHFORD TABLE LOOM - EIGHT SHAFT 410/610/800mm 16/24/32in INSTRUCTIONS ASHFORD TABLE LOOM - EIGHT SHAFT 410/610/800mm 16/4/3in ESTL1110016V1 Ashford Handicrafts Limited Factory and Showroom: 415 West Street PO Box 474, Ashburton 7700 New Zealand Telephone 64

More information

DIANA 16 SHAFT COMPUTER-DOBBY

DIANA 16 SHAFT COMPUTER-DOBBY 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com Loom Prepared by: Inspected by: Date: DIANA 16 SHAFT COMPUTER-DOBBY 2120-1624

More information

MIRA II Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: FAX:

MIRA II Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: FAX: 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the loom, unpack and lay out the loom components. Do NOT discard

More information

ASHFORD TABLE LOOM - FOUR SHAFT 410/610/800mm 16/24/32in

ASHFORD TABLE LOOM - FOUR SHAFT 410/610/800mm 16/24/32in INSTRUCTIONS ASHFORD TABLE LOOM - FOUR SHAFT 410/610/800mm 16/4/3in Ashford Handicrafts Ltd. Factory and Showroom: 415 West Street, PO Box 474, Ashburton, New Zealand Telephone 64 3 308 9087 Facsimile

More information

ABM International, Inc. Navigator Assembly Manual

ABM International, Inc. Navigator Assembly Manual ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)

More information

DOROTHY 24 v SHAFT LOOM SHAFT LOOM Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: FAX:

DOROTHY 24 v SHAFT LOOM SHAFT LOOM Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: FAX: DOROTHY 24 v2 2410-0000 4 SHAFT LOOM 2411-0000 8 SHAFT LOOM 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 PARTS AS SHIPPED: 1 pre-assembled loom 1(2) (3) head 4 shafts

More information

ARTISAT 36" JACK-TYPE 8 SHAFTS BACK HINGE TREADLES

ARTISAT 36 JACK-TYPE 8 SHAFTS BACK HINGE TREADLES ARTISAT 36" JACK-TYPE 8 SHAFTS BACK HINGE TREADLES 1009-3628 On receiving the loom, unpack and lay out the loom components Do NOT discard any packing material until all parts are inventoried. Check the

More information

COMPACT 24 KIT 8 shaft

COMPACT 24 KIT 8 shaft COMPACT 24 KIT 8 shaft 1023-0000 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the kit, unpack and lay out the

More information

MACHINE QUILTING FRAME

MACHINE QUILTING FRAME MACHINE QUILTING FRAME YOU WILL NEED TO PURCHASE: 5 pieces of 1-1/4 thin wall metal conduit (EMT) cut to your preferred length for the rollers. (Maximum 120 ) DETERMINING YOUR ROLLER LENGTH: Determine

More information

COLONIAL V2 8 &12s Jack type Back Hinge Treadle

COLONIAL V2 8 &12s Jack type Back Hinge Treadle COLONIAL V2 8 &12s Jack type Back Hinge Treadle 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com 8s 12s 45" 1051-0082 1051-0122

More information

Kromski Symphony Assembly Instructions

Kromski Symphony Assembly Instructions Kromski Symphony Assembly Instructions Important Notice If you have any difficulty in understanding these instructions, assembling the wheel, or having it operate to its fullest potential, WE WANT YOU

More information

OPERATIONS MANUAL. Port-O-Slitter

OPERATIONS MANUAL. Port-O-Slitter Tapco Products Company The World Leader in Specialty Tools for the Professional Port-O-Slitter OPERATIONS MANUAL General instructions, set up, accessories and guide to using your portable precision slitting,

More information

GOBELIN KIT 2 SHAFT FRAME 45", 60"

GOBELIN KIT 2 SHAFT FRAME 45, 60 GOBELIN KIT 2 SHAFT FRAME 45", 60" On receiving the loom, unpack and lay out the loom components Do NOT discard any packing material until all parts are inventoried. Check the parts received against the

More information

Kromski Minstrel Assembly Instructions

Kromski Minstrel Assembly Instructions Kromski Minstrel Assembly Instructions Important Notice If you have any difficulty in understanding these instructions, assembling the wheel, or having it operate to its fullest potential, WE WANT YOU

More information

Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions

Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit Screwdriver (Flat & Phillips) Measuring Tape Pencil 4 Level Plumb Line ¼ Masonry

More information

For additional assistance call

For additional assistance call The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or

More information

Mount to the Wall INSTALLATION MANUAL

Mount to the Wall INSTALLATION MANUAL Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut

More information

Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions

Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit Screwdriver (Flat & Phillips) Measuring Tape Pencil 4 Level Plumb Line ¼ Masonry

More information

Electric Skein Winder

Electric Skein Winder Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers

More information

ABM International, Inc.

ABM International, Inc. ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket

More information

This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.

This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4

More information

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL

More information

Q-Zone Hoop-Frame. Assembly Instructions. Copyright July 11, 2018 Grace Company (Reproduction Prohibited) Version 1.8

Q-Zone Hoop-Frame. Assembly Instructions. Copyright July 11, 2018 Grace Company (Reproduction Prohibited) Version 1.8 Q-Zone Hoop-Frame Assembly Instructions Copyright July 11, 2018 Grace Company (Reproduction Prohibited) Version 1.8 Table of Contents Table of Contents... i Warranty... ii Parts List Box 1...iii Box 2...

More information

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2. The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box

More information

ELIZABETH 30 SPINNING WHEEL

ELIZABETH 30 SPINNING WHEEL INSTRUCTIONS ELIZABETH 30 SPINNING WHEEL Single and Double Treadle Ashford Handicrafts Ltd. Factory and Showroom: 415 West Street, PO Box 474, Ashburton, New Zealand Telephone 64 3 308 9087 Facsimile 64

More information

L.L.Bean. Wooden Slat Bed

L.L.Bean. Wooden Slat Bed L.L.Bean Wooden Slat Bed Thank you for purchasing our Slat Bed. Assembly of this product requires A Phillips head screwdriver. We have found it helpful to have a second person present in at least one step

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

DOROTHY 15 ¾ SHAFT LOOM SHAFT LOOM SHAFT LOOM Savoie C. P. 4 Plessisville, Qc. G6L 2Y6

DOROTHY 15 ¾ SHAFT LOOM SHAFT LOOM SHAFT LOOM Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 DOROTHY 15 ¾ 2110-0000 4 SHAFT LOOM 2111-0000 8 SHAFT LOOM 2112-0000 12 SHAFT LOOM PARTS AS SHIPPED: 1 pre-assembled loom

More information

User Instructions Multiline Otter Scoreboard Caddy Assembly

User Instructions Multiline Otter Scoreboard Caddy Assembly List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)

More information

Thor Audi A4/S4 Skid Plate Installation Instructions

Thor Audi A4/S4 Skid Plate Installation Instructions Thor Audi A4/S4 Skid Plate Installation Instructions Parts List: 1 Aluminum Skid Plate 2 Aluminum Side Wings 10 10mm Flat Washers 3 8mm Flat Washers 3 8mm Speed Clips 2 10x40mm Bolts 3 8x35mm Bolts 2 Rivet-nuts

More information

3,500/4,500lb. Vertical Cable Feighner Lift

3,500/4,500lb. Vertical Cable Feighner Lift 3,500/4,500lb. Vertical Cable Feighner Lift CAUTION - PUT SAFETY FIRST 1. Before attempting to install or operate this lift, study and fully understand the proper operating procedures and safety precautions

More information

L.L.Bean. Farmhouse Futon

L.L.Bean. Farmhouse Futon L.L.Bean Farmhouse Futon Thank you for purchasing our Farmhouse Futon. Assembly of this product requires a Phillips Head Screwdriver and Flat Head Screwdriver. We have found it helpful to have a second

More information

TROLLA LEAVY 97 CM Lawn sweeper

TROLLA LEAVY 97 CM Lawn sweeper TROLLA LEAVY 97 CM Lawn sweeper Artikel nr.: 1008 EN Operating manual 014/1 Dear Customer, Congratulations on your new Trolla product. We hope you will enjoy it. Checkout with your new Trolla product may

More information

MODEL 83 Pail Handler

MODEL 83 Pail Handler MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE

More information

Juki Quilting Frame. Assembly and Use Instruction Manual. Max Overall Dimensions: Length Crib: King: Tall: Wide: 42

Juki Quilting Frame. Assembly and Use Instruction Manual. Max Overall Dimensions: Length Crib: King: Tall: Wide: 42 Juki Quilting Frame Assembly and Use Instruction Manual Max Overall Dimensions: Length Crib: 63 1 4 King: 128 1 4 Tall: 45 3 4-51 3 4 Wide: 42 Copyright January, 2015 Version 9.6 (Page 1) Contents Parts

More information

Assembly Instructions: AM-10 Hand & Foot Cycle Early Intervention Part #: 50-HFC-0105

Assembly Instructions: AM-10 Hand & Foot Cycle Early Intervention Part #: 50-HFC-0105 Assembly Instructions: AM-10 Hand & Foot Cycle Early Intervention Part #: 50-HFC-0105 Refer to the following instructions on how to assemble your tryke. Study the instructions carefully before beginning

More information

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 ) P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

Instructions. Assembly

Instructions. Assembly Assembly Instructions The band weaving loom has a long tradition in the history of weaving in Sweden. Bands are used for many things, like the hanging tapes sewn into towel hems. Wider bands can be used

More information

The Queen Quilter Professional Quilters Kit Frame

The Queen Quilter Professional Quilters Kit Frame The Queen Quilter Professional Quilters Kit Frame Assembly Instructions Table of Contents: Before you begin......................... Pg. 2 Wood parts............................. Pg. 3 Hardware..............................

More information

SAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20

SAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42-55 Page 20 SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management

More information

Kromski Prelude. Assembly Instructions

Kromski Prelude. Assembly Instructions Kromski Prelude Assembly Instructions Important Notice If you have any difficulty in understanding these instructions, assembling the wheel, or having it operate to its fullest potential, WE WANT YOU TO

More information

Side Winder R o u t e r L i f t.

Side Winder R o u t e r L i f t. Woodpeckers PRECISION WOODWORKING TOOLS Side Winder R o u t e r L i f t. INSTALLATION INSTRUCTIONS The wrench handle must be pointing left in order to fully insert or remove it. Lift Wrench Once fully

More information

Please Do Not Return This Product To The Store!

Please Do Not Return This Product To The Store! MODEL NOS. T8512 TOURNAMENT SERIES 3 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts

More information

A SERIES PRODUCTION DOBBY LOOM

A SERIES PRODUCTION DOBBY LOOM A SERIES PRODUCTION DOBBY LOOM User s Manual AVL Looms 2360 Park Avenue Chico, CA 95928-6785 U.S.A. 530 893-4915 530 893-1372 (fax #) info@avlusa.com (e-mail) www.avlusa.com Copyright 2008 All Rights Reserved

More information

TRAILMATE METEOR ASSEMBLY MANUAL

TRAILMATE METEOR ASSEMBLY MANUAL TRAILMATE METEOR ASSEMBLY MANUAL The Trailmate Meteor recumbent has been designed for easy assembly. This means more time to enjoy the smooth ride with single speed, 3 speed coaster brake and 21 speed

More information

RPS. XR Front Drive Updates CORPORATION

RPS. XR Front Drive Updates CORPORATION FACTORY CAT 1. To start a replacement of the XR Front Wheel Drive, make sure the machine is on level ground with the rear wheels chocked and always disconnect the batteries. 2. Locate the Positive and

More information

WORKSHOP DOBBY LOOM. User s Manual. 16 Workshop Dobby Loom 24 Workshop Dobby Loom

WORKSHOP DOBBY LOOM. User s Manual. 16 Workshop Dobby Loom 24 Workshop Dobby Loom WORKSHOP DOBBY LOOM User s Manual 16 Workshop Dobby Loom 24 Workshop Dobby Loom AVL Looms 3851 Morrow Lane, Suite 9 Chico, CA 95928-8305 U.S.A. 530 893-4915 530 893-1372 (fax #) info@avlusa.com (e-mail)

More information

Queen Wingback Bed King Wingback Bed

Queen Wingback Bed King Wingback Bed Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock

More information

Machine Quilting Frame assembly, and instruction manual

Machine Quilting Frame assembly, and instruction manual Machine Quilting Frame assembly, and instruction manual Table of Contents Parts List................. Pg. 2 Step 1 - Legs............... Pg. 4 Step 2 - Lower Leg Brace....... Pg. 5 Step 3 - Frame Ends..........

More information

General Features. Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized

General Features. Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized General Features Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized Two Sizes Short Box :74 L X 47 W X 7 T and Long Box 92 L X 47 W X 7 T All Aluminium

More information

WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount

WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE

More information

FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS

FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.

More information

M10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5" PH Wood Screws. (30) Included - (24) Required

M10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5 PH Wood Screws. (30) Included - (24) Required Door System Unit - Hardware Tools Included: (2) 2mm Allen Wrenches, (2) 3mm Allen Wrenches, (2) 4mm Allen Wrenches, (2) 6mm Allen Wrenches, and (1) 8mm T-Handle Allen Wrench Tools Required: Phillips Screwdriver,

More information

L.L.Bean. Platform Bed

L.L.Bean. Platform Bed L.L.Bean Platform Bed Thank you for purchasing our Platform Bed. Assembly of this product requires a Phillips head and a flat head screwdriver. We have found it helpful to have a second person present

More information

Installation And Care Instructions. Vertical Honeycomb Shades

Installation And Care Instructions. Vertical Honeycomb Shades Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...

More information

Therma-Tru Door Gallery Setup Instructions Swing Unit with Hardware Kit - Hardware Part # MADGSWU15 (Swing Unit) Part # MADGHKSU10 (Hardware Kit)

Therma-Tru Door Gallery Setup Instructions Swing Unit with Hardware Kit - Hardware Part # MADGSWU15 (Swing Unit) Part # MADGHKSU10 (Hardware Kit) Swing Unit with Hardware Kit - Hardware Tools Included: 4mm Allen Wrench, 6mm Allen Wrench, 8mm T-Handle Allen Wrench (1) 3/4" Drill Bit, (1) 7/32" Drill Bit and Hole Template Guide Tools Required: Phillips

More information

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

TITAN2-EDGE Public Access Computer Station Dual Track

TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the

More information

WORKSHOP DOBBY LOOM. User s Manual. 16 Workshop Dobby Loom 24 Workshop Dobby Loom

WORKSHOP DOBBY LOOM. User s Manual. 16 Workshop Dobby Loom 24 Workshop Dobby Loom WORKSHOP DOBBY LOOM User s Manual 16 Workshop Dobby Loom 24 Workshop Dobby Loom AVL Looms 2360 Park Avenue Chico, CA 95928-6785 U.S.A. 530 893-4915 530 893-1372 (fax #) info@avlusa.com (e-mail) www.avlusa.com

More information

Interactive Monitor Arm

Interactive Monitor Arm Interactive Monitor Arm Tools Required -5mm Allen wrench -Phillips screwdriver -Plastic mallet There are two ways to attach a Monitor Arm to a Full Frame; with a Beam, or with a Post Mount. Both methods

More information

6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405)

6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405) INSTALLATION INSTRUCTIONS FOR THE TAILGATE WITH LATCH AND LINK ASSEMBLY 76-87 FORD SHORT & 53-87 FORD LONG FLARESIDES 1. Assemble the bed and make sure the box is square. Measure the distance between the

More information

INSTALLATION AND CARE INSTRUCTIONS

INSTALLATION AND CARE INSTRUCTIONS INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5

More information

Continuum Frame Assembly Instructions

Continuum Frame Assembly Instructions Continuum Frame Assembly Instructions Copyright January 1, 2017 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.2 Table of Contents Continuum Frame Table of Contents... i Warranty...ii

More information

MM750 Installation Instructions

MM750 Installation Instructions MM750 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on

More information

RIGID HEDDLE LOOM. Instructions for Assembly, Warping, and Weaving

RIGID HEDDLE LOOM. Instructions for Assembly, Warping, and Weaving RIGID HEDDLE LOOM Instructions for Assembly, Warping, and Weaving Schacht Spindle Co., Inc. 6101 Ben Place Boulder, CO 80301 303-442-3212 info@schachtspindle.com www.schachtspindle.com Rigid Heddle Loom

More information

Wooden Frame Type Instruction Manual

Wooden Frame Type Instruction Manual Wooden Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand

More information

model tsa-sa48 Sliding Crosscut Table installation guide

model tsa-sa48 Sliding Crosscut Table installation guide model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop

More information

Installation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100

Installation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100 Installation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100 It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating

More information

OPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

OPERATOR'S MANUAL 46 SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.

More information

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems

More information

Workshop Dobby Loom User s Manual

Workshop Dobby Loom User s Manual Workshop Dobby Loom User s Manual Figure 1-16" Workshop Dobby Loom Figure 2-24" Workshop Dobby Loom AVL Looms 2360 Park Avenue Chico, CA 95928-6785 800 626-9615 530 893-4915 530 893-1372 (fax) http:\\www.avlusa.com

More information

SAVVY OFF ROAD GAS TANK SKID INSTALLATION INSTRUCTIONS

SAVVY OFF ROAD GAS TANK SKID INSTALLATION INSTRUCTIONS It is best to work with a fuel tank that has the least amount of fuel in it as possible. Thank you for purchasing the best skid on the market. Please follow these instructions and your installation should

More information

LEG CURL IP-S1315 INSTALLATION INSTRUCTIONS

LEG CURL IP-S1315 INSTALLATION INSTRUCTIONS LEG CURL IP-S35 INSTALLATION INSTRUCTIONS Copyright 2009. Star Trac by Unisen, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written

More information

Emilia. The Folding Rigid Heddle Loom. Learning to weave on your Emilia loom by Joanne Hall

Emilia. The Folding Rigid Heddle Loom. Learning to weave on your Emilia loom by Joanne Hall Emilia The Folding Rigid Heddle Loom Learning to weave on your Emilia loom by Joanne Hall Heddle Handle Heddle Bracket Rigid Heddle Warping peg The Emilia Loom and Accessories Warp beam Texsolv cord Folding

More information

MOTORIZED STANDARD SHADE WITH CABLES Installation Instructions

MOTORIZED STANDARD SHADE WITH CABLES Installation Instructions Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench

More information

Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions

Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips

More information

ASHFORD COUNTRY SPINNER 2

ASHFORD COUNTRY SPINNER 2 INSTRUCTIONS ASHFORD COUNTRY SPINNER 2 CS110618V8 Ashford Handicrafts Limited Factory and Showroom: 415 West Street PO Box 474, Ashburton 7700 New Zealand Telephone 64 3 308 9087 Facsimile 64 3 308 8664

More information