Taylorcraft Indoor / Cul-De-Sac Flyer
|
|
- Lizbeth Stokes
- 6 years ago
- Views:
Transcription
1 Taylorcraft Indoor / Cul-De-Sac Flyer Taylocraft Specifications Wingspan: 28.0 in. Wing Area: 117 sq. in. Weight (Ready to Fly): oz. Wing Loading: oz. / sq. ft. LIABILITY RELEASE In that Mountain Models has no control over the final assembly or material used for final assembly, no liability shall be assumed or accepted for any damage resulting from the use by the user of the final userassembled product. By the act of using the user-assembled product, the user accepts all resulting liability. If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return the kit immediately in new and unused condition. THIS PRODUCT IS NOT INTENDED FOR CHILDREN 12 YEARS OF AGE OR YOUNGER Warning: This product may contain chemicals known to the State of California to cause cancer or birth defects or other reproductive harm
2 Revision History Date Revision Notes/Comments 04/07/ Initial Release 09/13/ Production Release Thank you for purchasing the Mountain Models Taylorcraft. The Taylorcraft is a super lightweight, easy to fly, but fun to toss around Depron plane. High quality laser cut Depron and plywood parts make the assembly of this laser cut model airplane kit a breeze! We think you ll find this plane to be a lot of fun, being able to be flown indoors and small outdoor spaces. It handles some wind just fine, so you ll be fine at a larger field as well. Thank you, Brian Eberwein Mountain Models PO Box 9557 Colorado Springs, CO Phone:
3 Parts List Number in Kit Description of Part 1 Set 3mm Depron Parts 4 1/64 Plywood LE & TE Reinforcements 1 1/16 Plywood Firewall 1 1/32 Plywood Sheet 1 1/32 Balsa Sheet 1 3/32 Balsa Sheet x 12 Wire x 12 Wire Bagged Parts 2 Wheels 2 DuBro Wheel Keepers 1 1/64 Plywood Elevator Reinforcement 1 1/32 Plywood Tail Skid 4 Motor Mount Screws Electronics You Will Need 1 ea. 10 gram, 2000 KV Outrunner 1 ea. GWS 6x3 HD Prop 2S-300 to 360 LiPo 1 ea. 6 Amp Brushless ESC 2 ea. 3.7 gram servos 1 ea. Lightweight (Berg4L, or similar) 4-channel RX 1 ea. 3 channel radio minimum Building Materials You Will Need Smooth and flat work surface Wax paper or clear plastic wrap to protect the work surface Foam safe Cyanoacrylate (CA) glue and accelerator (or 5-minute epoxy, or white Gorilla Glue) Hobby knife with #11 blades Needle nose pliers Wire cutters Screwdrivers Sanding block, 320 grit sandpaper 3
4 Step 1: Glue the 1/64" plywood leading and trailing edge reinforcements in place on the wing, as shown. Use a slower setting foam safe CA or 10 minute epoxy (sparingly). Make sure the wing is flat and that the plywood is fully seated against the foam. Step 2: Glue the 3/32" balsa ribs in place on each wing, as shown. The engraved lines on the wing go on the bottom and help the wing bend to the correct shape. Pile magazines on top of the wing, while the glue is drying, to make sure that the wing comes out straight and properly curved to the airfoil shape when the glue is dry " Plywood Wing Spar Step 3: Glue the 1/32" plywood wing joiner in place on the left wing half, as shown. Make sure it is flush with the top of the wing. When it is dry, glue it to the other wing half. Use some glue to fill in the gap on the bottom of the wing where the two halves come together.
5 If you are using a slower setting glue, you can assemble/glue up the entire fuselage at once. Step 4: Glue the formers in place on the crutch, as shown in the image. MAKE SURE that the plywood firewall is glued so the engraved text faces FORWARD. Step 5: Glue on the fuselage sides, as shown. Tape the rear end of the fuselage together to help in alignment. Step 6: Glue on the fuselage top front, windshield, and rear fuselage top, as shown.
6 Step 7: Bend the landing gear wires, as shown in the wire drawing sheet on the last page of this manual. Step 8: Glue the 1/32" balsa landing gear mount together, using thick CA, with the landing gear wire in between. Step 9: Glue the landing gear fairings onto the landing gear wire. You can groove the foam so the wire sits in it slightly. This gives a better glue joint. Step 10: Place the wheels onto the landing gear wire and secure with the shrink tubing. Step 11: Glue the landing gear assembly into the fuselage, as shown, onto the front of the lower former. The balsa landing gear assembly should be flush with the bottom of the former. Step 12: Glue in the tail gear skid against the inside of the fuselage side. It should look like it does in the side view on the next page. Step 13: Glue in the fuselage fiewall doublers. They should be glued to the inside of the fuselage, pressed up against the firewall.
7 Step 14: Glue the stabilizer and vertical fin in place, as shown. MAKE SURE that the stabilizer is horizontal and that the vertical fin is at a 90 degree angle to the stabilizer. Step 15: Bevel the hinge side of the rudder and stabilizer, as shown. Use a sharp X-Acto and a metal straight edge. Step 16: Glue the 1/64" plywood reinforcement onto the elevator as shown, making sure the elevator is flat as the glue dries. Take note as to where the control horn hole is, in relation to what side the plywood is glued onto. Step 17: Glue the control horns into the rudder and elevator, as shown in the drawings. MAKE SURE you glue them onto the correct side.
8 Step 18: Slide the elevator and rudder pushrods into the fuselage, as shown in the drawing. The adjustment "V" bends go inside the fuselage. Step 19: Slide the elevator onto the elevator pushrod and use tape to hinge the elevator to the stabilizer. Step 20: Slide the rudder onto the rudder pushrod and use tape to hinge the rudder to the vertical. Step 21: Mount the servos in the fuselage, as shown. Slide the servo horn onto the Z-bend in the pushrod and secure the servo horn to the servo. BATTERY ESC Step 22: Mount the ESC and receiver in the location shown in the drawing. Step 23: Use the included Velcro to mount your battery as shown in the drawing. RX goes against the fuselage side. Step 24: Mount the motor mount to the firewall, using the included #2 screws. Mount the motor to the motor mount and secure the set screws.
9 Step 25: Hook up your radio and make sure everything works, the servos are centered, the rudder and elevator are centered, and your controls are moving the right direction. Step 27: Set your control throws to: LOW RAETS: Rudder: 3/8" each way Elevator: 5/16" each way HIGH RAETS: Rudder: 3/4" each way Elevator: 3/4" each way Step 26: Glue the wing onto the fuselage, making sure it is centered. You may need to trim just a little off the front former so it sits flat. Step 28: Balance the plane at 1.5" behind the leading edge of the wing.
10
Round2it! Mini Electric Sailplane. Round2it
Round2it! Mini Electric Sailplane Round2it Wingspan: 36.0 in. Length: 22.4 in. Wing Area: 164 sq. in. Weight (Ready to Fly): 4.0 to 4.8 oz. Wing Loading: 3.5 4.2 oz. / sq. ft. Version 1.0, September 10,
More informationMercurE Mini Old Timer Electric Model
MercurE Mini Old Timer Electric Model MercurE Specifications Wingspan: 31.6 in. Length: 20.6 in. Wing Area: 153 sq. in. Weight (Ready to Fly): 4.9 to 5.4 oz. Wing Loading: 4.6 5.1 oz. / sq. ft. Version
More informationC-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
More information(Build Instructions)
(Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS
More informationParkJet Builder s Manual
ParkJet Builder s Manual Thank you for purchasing the ParkJet. The ParkJet is a profile ducted fan airplane that can be flown in a larger park. The ParkJet was initially designed by Scott Stoops and modified
More informationBogie 72. Old Timer Electric Model. Little Bogie Specifications
Bogie 72 Old Timer Electric Model Little Bogie Specifications Wingspan: 72.0 in. Length: 39.0 in. Wing Area: 655 sq. in. Weight (Ready to Fly): 28 to 30 oz. Wing Loading: 6.1 6.6 oz. / sq. ft. Version
More informationRoland c.ii Walfisch Ultra Micro Cartoon Scale WW I Electric Model
Roland c.ii Walfisch Ultra Micro Cartoon Scale WW I Electric Model Roland c.ii Walfisch Wingspan: 13.35 in. Length: 13.4 in. Wing Area: 78 sq. in. Weight (Ready to Fly): 1.4 oz. Wing Loading: 2.6 oz. /
More informationSwitchBack Senior. SwitchBack Senior Specifications
SwitchBack Senior SwitchBack Senior Specifications Wingspan: 55.4 in. Length: 41 in. Wing Area: 597 sq. in. Weight (Ready to Fly): 34 to 37 oz. Wing Loading: 8.2 to 8.9 oz. / sq. ft. Version 1.05, March
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationULS Cherokee. Ultra Low Speed aircraft for indoor RC flying. Zippkits. Specifications: Required to complete:
Zippkits ULS Cherokee Ultra Low Speed aircraft for indoor RC flying. Specifications: Span- 28 inches Wing Area- 151 Sq/In Wing Loading- 3.0 ounces/ft Weight- 3.5 ounces RTF Build time- 1-2 Hours Radio-
More informationMagpie. Foam Trainer. Magpie Specifications
Magpie Foam Trainer Magpie Specifications Length: 34in. Wingspan (SF): 46in. Wing Area (SF): 414in 2 Wingspan (SP): 40in. Wing Area (SP): 360in 2 Weight (without battery): 12oz. Thank you for purchasing
More informationE-AERO EPP PITTS KIT From BP HOBBIES. Parts Included in kit
E-AERO EPP PITTS KIT From BP HOBBIES Parts Included in kit Thank you for purchasing the BP Hobbies/E-aero EPP Pitts. Please take the time to read through the instruction manual before beginning the build.
More informationEva. Extremely Versatile Airframe
Eva Extremely Versatile Airframe Eva Specifications Length: 32 Weight (without battery): ~12oz. Revision History Date Revision Notes/Comments 6/3/05 Document initial creation. Thank you for purchasing
More informationMillennium RC presents The New and Improved (now even easier to build and cover!) SSX X-Trainer Build Kit
Millennium RC presents The New and Improved (now even easier to build and cover!) SSX X-Trainer Build Kit Wing span: Approx. 42 Wing Area: 504 sq. in. Wing Loading: 6.71 oz/ sq. ft. Introduction: The Slow
More informationCitabria Pro. Aerobatic Parkflyer. by Joel Dirnberger
Citabria Pro Aerobatic Parkflyer by Joel Dirnberger Revision C: December 21, 2004 Citabria Pro Building Instructions Length: Wingspan: Wing Area: Flying Weight: Wing Loading: Functions: Specifications:
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationMOUNTAIN MODELS P-51 Mustang. 1/12 Scale Electric Park Flyer. Copyright Mountain Models
1 MOUNTAIN MODELS www.mountainmodels.com P-51 Mustang 1/12 Scale Electric Park Flyer Wingspan: 37, Wing Area: 254 sq. in., Weight: 15 to 19.5 oz Instructions Version 1.4, May 23, 2007 Kit Contents: 2 1.
More informationNASTY Build Guide. Supplies needed
NASTY Build Guide Supplies needed Blucore or Depron Foam. Blucore (Fan Fold Foam) is available at Lowes. Approximately $25 for 50 feet of Blucore. Depron can be ordered on the internet for slightly more.
More informationDandy Sport Builder s Manual
Dandy Sport Builder s Manual Thank you for purchasing the Dandy Sport. The Dandy Sport has been designed as an easy to build aileron trainer. Take your time and enjoy building this plane. Specifications:
More informationThank you for your purchase of the Lee Ulinger, FoamtanaS, Yak-55, or Extra 330 3D Depron foam, Aerobatic airplane.
Thank you for your purchase of the Lee Ulinger, FoamtanaS, Yak-55, or Extra 330 3D Depron foam, Aerobatic airplane. Tools you will need to build Recommended additional items: #11 hobby knife Motor: Hacker
More informationSwitchback Sport Builder s Manual
Switchback Sport Builder s Manual Thank you for purchasing the Switchback Sport. The Switchback Sport has been designed for the novice to intermediate pilot who wants a plane with good performance that
More informationParts Identification
We are excited to introduce the Model Aero Aqua Sport. This is an excellent sport flyer, equally at home flying from grass fields, water, or even snow! The unique V-tail gives the Aqua Sport a distinctive
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More informationStearman PT-17 KIT WARRANTY
Stearman PT-17 KIT # K-306 Assembly Instructions Version 2 02-17-16 Designed by Tom Herr WARRANTY Sig Manufacturing Co, Inc. guarantees this kit to be free from defects in both material and workmanship
More informationMagpie AP. Aerial Photography Airplane
Magpie AP Aerial Photography Airplane Magpie Specifications Length: 36in. Wingspan: 54in. Wing Area: 486in 2 Weight (without battery): 19 oz. Thank you for purchasing the Magpie AP. This model is an elevator/rudder
More informationLoLo. A sporty parkflyer with an Old Timer flair! Designed by: Tres Wright Kitted by: Park Scale Models
LoLo A sporty parkflyer with an Old Timer flair! Designed by: Tres Wright Kitted by: Park Scale Models http://www.parkscalemodels.com/ Assembly Instructions General Information The laser cutting process
More informationI hope you enjoy the Spirit as much as I have. Scott DeTray Model Aero
We are excited to introduce the Model Aero Spirit. Inspired by the magnificent Northrop Grumman B-2 Spirit Stealth Bomber, the Spirit is a great flyer, on land or water. It tracks like an arrow and is
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationWarbird Series Zero - 32 Assembly Manual
Warbird Series Zero - 32 Assembly Manual Specifications Wing Span: 32 inches Wing Area: 210 in 2 Fuselage Length: 26 inches Weight (ready to fly): 11 to 13 oz. Wing Loading: 7.5 to 8.9 oz/ft 2 Designed
More informationHIGH-END TECHNOLOGY. Electric ducted fan Starfighter
HIGH-END TECHNOLOGY RC Electric ducted fan Starfighter First we want to thank and congratulate you with your decision in buying one of our Kits. The Starfighter puts together very easily so there is not
More information28in Super EVA Foam. F-22 Raptor Kit. Specifications. Wingspan: 27.5in (700mm) Length: 38.3in (975mm) Flying Weight: Approx. 1.
28in Super EVA Foam F-22 Raptor Kit Specifications Wingspan: 27.5in (700mm) Length: 38.3in (975mm) Flying Weight: Approx. 1.2lbs (530g) Dear Customer, Congratulations on your purchase of 28in F22 Raptor
More informationYour kit contains the following parts. Please check your kit for any missing or damaged parts before starting construction.
Your kit contains the following parts Please check your kit for any missing or damaged parts before starting construction COMPLETE KIT PARTS LIST 1 Plan Sheet #1 1 Plan Sheet #2 2 Decal Sheet 2 White Tissue
More information6mmFlyRC.com Super Bandit Assembly Instructions
Assembly Instructions Start the assembly with forward fuselage. Lay the two fuselage sides down on a flat surface and glue the foam corner doublers to the locations shown on the plans. Make sure to make
More informationA Piaggio-inspired park flyer
Clark Salisbury's SkyTwin A Piaggio-inspired park flyer B efore I discuss building the SkyTwin, I should explain my reasons for designing, building, and flying such an aircraft. I have always been fascinated
More informationCorvus Racer Colour schemes. AeroPlus RC Copyright 2013 All Rights Reserved
Corvus Racer 540 59 Item No:A E050003 Specifications WING SPAN: 59"(1500mm) LENGTH: 54.1"(1374mm) WING AREA: 654sq.in.(42.2sq.dm.) FLYING WEIGHT: 4.6 5.3lbs(2000 2300g) Electric:Brushless outrunner 8Oz.
More informationVT-ALLROUNDER V4 1500MM CORO 3/4 Channel Trainer Airplane
Congratulations on your purchase of the VT- AllRounder 1500MM Trainer Airplane Kit.. Hope these build instructions help you complete the build. Though the build itself doesn't take much time, just be sure
More informationSpecifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive
Specifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive Airframe Kit (Included Contents) * Airframe Parts Sheets (Depron)
More information25mm EPP SU31. Instruction Manual. Specifications
25mm EPP SU31 Instruction Manual Specifications Wingspan: 39.4in (1000mm) Length: 42in (1070mm) Wing Area: 448sq in (28.9sq dm) Flying Weight: Approx. 1.5lb (650-710g) Dear Customer, www.valuehobby.com/su31-epp.html
More informationRevolution 3D-mini ARF
Revolution 3D-mini ARF 1 Included Hardware 4 Dubro Micro Control Horns #DUB848 2.32 x 18" Linkage Wire (Music Wire) 1 1.5 x 1.25 x 1/8 Balsa Ply (for motor mount) 1 5" piece of Velcro (Optional recommended,
More informationCARL GOLDBERG PRODUCTS, LTD.
Eagle 400 WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could be dangerous.
More information1/6 PA-25 PAWNEE. *Specifications are subject to change without notice.*
1/6 PA-25 PAWNEE INSTRUCTION MANUAL [ A335 Kit ] Wing Span : 72 in / 1830 mm Wing Area : 736 sq in / 47.5 sq dm Flying Weight : 6.6 lbs / 3000 g Fuselage Length : 48 in / 1220 mm Requires : "Glow Power"
More informationThe BIPE NX Assembly Manual
The BIPE NX Assembly Manual Specifications Wing Span: 34 inches Wing Area: 550 in 2 Fuselage Length: 36 inches Weight (ready to fly): 20 to 24 oz. Wing Loading: 5.2 to 6.3 oz/ft 2 Designed by Jim Vigani
More informationF-16 Falcon 70mm EDF
F-16 Falcon 70mm EDF Instruction manual Specifications: Winspan: 640 mm Length: 990 mm Weight: 900-1100 gram Ducted fans 70mm x 1 Required tools and components:. 4 ch. Computer Radio system w/ 2 servos.
More informationLANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.
LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for
More information43in EPP Acrocub Instruction Manual
43in EPP Acrocub Instruction Manual Specifications Wingspan: 43.3in (1100mm) Length: 41.3in (1050mm) Flying Weight: Approx. 1.5lb (670g) Dear Customer, Congratulations on your purchase of 43in EPP Acrocub
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationHobby Lobby Zip Supplementary instructions Please refer to the included drawings while using these assembly instructions
Materials needed: 15 or 30 minute epoxy Medium CA Masking tape Scotch tape Servo Tape Wax paper Tools Needed: Pencil or marker Flat building surface Hobby knife or razor blade 7/64" or 3mm drill bit 3/16"
More informationCOMET 24" HELLCAT REPRODUCTION ASSEMBLY GUIDE
COMET 24" HELLCAT REPRODUCTION A RUBBER POWERED 24" WING SPAN MODEL BY PAUL BRADLEY ASSEMBLY GUIDE AUGUST 2016 CHANGES MADE TO THE ORIGINAL The following changes were made to the original Comet kit structural
More informationTHE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE
THE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE Apogee is the intermediate sailplane designed to be competitive in AMA duration contests. Effective spoilers, rudder and full flying stabilizer
More informationGYM-E. Instruction Manual - Version 1.03
GYM-E Original Design by Todd Long Instruction Manual - Version 1.03 Span 31 in. / Length 27 in. / Area 265 Sq. In. / Weight 4.5-6.5 oz. Gym-E kit reproduced with permission by Stevens AeroModel 2008 Stevens
More informationCover the wing trailing edge and the aileron leading edge with strapping tape as shown.
Cover the wing trailing edge and the aileron leading edge with strapping tape as shown. The aileron hinges are done using strapping tape on the top and bottom surfaces of the ailerons as shown. Make sure
More informationDesigned in 2005 by Bernard Burton. Assembly manual Bernard Burton DRAFT 1
Designed in 2005 by Bernard Burton Assembly manual 2005 - Bernard Burton DRAFT 1 The plans can be requested via this link http://www.gundersonaerodesign.com/m12plansreq.htm The laser kit is available here
More informationTaylorcraft 72 KIT WARRANTY
Taylorcraft 72 KIT # K-502 Assembly Instructions Revision:02 12-10-13 WARRANTY Alien Aircraft Corp. guarantees this kit to be free from defects in both material and workmanship at the date of purchase.
More informationCOMET SENIOR DART REPRODUCTION ASSEMBLY GUIDE
COMET SENIOR DART REPRODUCTION A RUBBER POWERED 24" WING SPAN MODEL BY PAUL BRADLEY ASSEMBLY GUIDE JANUARY 2018 CHANGES MADE TO THE ORIGINAL The following changes were made to the original Comet kit structural
More informationRYAN STA SAFETY PRECAUTIONS. "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. This radio control model is not a toy!
RYAN STA "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek advice from people with model building
More informationCARL GOLDBERG PRODUCTS, LTD.
Chipmunk 400 WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could be dangerous.
More informationSuper Sky Surfer 2000 Assembly Instructions
Super Sky Surfer 2000 Assembly Instructions Note: Plug and Play version of the Sky Surfer comes with fuselage pre-glued and motor/servos installed. If you wish to route antennas or wires through the tail,
More informationCombat Foamie. An electric powered model made from sheet foam for full contact combat matches. Designed by. Plan by Paul Bradley. Jerry W.
Combat Foamie An electric powered model made from sheet foam for full contact combat matches Designed by Jerry W. Hagood Plan by Paul Bradley July 2010 Combat Foamie Top View 22.9 CG is 7.3 back from nose
More informationORIGAMI E2. An electric powered model made from sheet foam based on the configuration of a paper glider. Concept and general arrangement by
ORIGAMI E2 An electric powered model made from sheet foam based on the configuration of a paper glider. Concept and general arrangement by Jack Pignolo Plan by Paul Bradley February 2010 ORIGAMI E2 38
More informationPiper Cherokee /3 scale. Construction Manual
Piper Cherokee 140 1/3 scale Construction Manual STAB CONSTRUCTION 1. Remove foam cores from cradle and place on flat surface. Inspect pieces before you epoxy halves together making sure leading and trailing
More informationS.E.5a (Build Instructions)
S.E.5a (Build Instructions) Specifications Wingspan: 38 cm Length: 31cm Flying Weight: 41 Channels: 3 (Rudder Elevator Throttle) Suggested Receiver: 3Ch Brick Motor: 7mm Geared Motor Airframe Only Kit
More informationStingray. A micro RC Pusher Jet for 12 mm direct drive motors.
Stingray A micro RC Pusher Jet for 12 mm direct drive motors. Designed by: Ethan, Aaron, and David Payne BlueSkyRC.com Laser Cut by: JTECH Laser (http://jtechlaser.com/) General Information Though this
More informationHIGH-END TECHNOLOGY. Electric ducted fan rafale
HIGH-END TECHNOLOGY RC Electric ducted fan rafale First we want to thank and congratulate you with your decision in buying one of our Kits. The Rafale puts together very easily so there is not much explanation
More informationSZD-10 bis CZAPLA ASSEMBLY MANUAL IN PICTURES
1 RUDDER Plan and parts: 2 Assembly steps: Photo above: glue together rudder spar, ribs and trailing edge. Clamp spar to a flat surface (chipboard on the photo) and make sure the straight aligment of the
More informationBuilding Tips This model can be built using the following types of adhesives:
Page 1 Building Tips This model can be built using the following types of adhesives: Epoxy (with or without microballons) Odorless cyanoacrylate (CA) with accelerator UHU Creativ for Styrofoam (or UHU
More informationFLITZEBOGEN-2 Assembly instructions
FLITZEBOGEN-2 Assembly instructions Trim the end of the fuselage to the length of 925mm from the nose. Be careful to avoid splitting the carbon fibers. Sand the base of the stab mount in preparation for
More informationSbach 1,2m 3D/aerobatic EPP model Building instructions
Sbach 1,2m 3D/aerobatic EPP model Building instructions Please refer to the Diagram sheet Diagrams A, B Press 2 carbon strips (1x3x1000 mm) into the grooves in the sides of the fuselage central part (the
More informationLARK. Classic Legal Precision Stunter RSM DISTRIBUTION. presents. Charles Mackey. Wing Area 570sq. Wingspan 52.
RSM DISTRIBUTION presents LARK By Charles Mackey Photo _ Bob Hunt Classic Legal Precision Stunter Wingspan 52 Length 39.5 Wing Area 570sq Motor 35-46 www.rsmdistribution.com Page 2 Thank you for purchasing
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More informationThe Olympic DLG. (Discus launch glider) by Chris Brislin
The Olympic DLG (Discus launch glider) by Chris Brislin 1 Contents Parts List/ What you need 3 Before you begin 4 Wing Construction 5-9 Pod Construction 9-13 Tail assembly 13-? Control linkages 9-10 Finishing
More informationLANIER - Double Trouble - INSTRUCTIONS. Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply
Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply Other Parts 2 Aluminum Gear 1 3/32 Music wire tail skid 2 Elevator and J-plane joiner wire
More information90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS This design is basically an enlargement of the very popular fun scale Mustang 60 Size. You can build it light
More informationInstruction Manual. Specification:
Instruction Manual H I G Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1830gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo H W I N G KIT CONTENTS: We have
More informationHigh performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
More informationLANIER Dominator INSTRUCTIONS
ADDITIONAL EQUIPMENT NEEDED TO COMPLETE YOUR DOMINATOR 500 General 3.2 to 4.2 Size two stroke R/C engine, muffler, and engine mount Gas or glow fuel line Minimum of 4 channel radio set required (4-5) 70
More informationuin RC FPRC ZERO Specificationss Empty Weight
Flying Pengu uin RC FPRC ZERO Specificationss Wing Span 42.75 (1085 mm) Fuselage length 30.5 ( 775 mm) Empty Weight 9.5 10 oz. (150 160g) Estimated Flying Weight 20 255 oz. (320 400g) Wing Area: 151 sq.
More informationŸ Battery Strap Ÿ Paper Knife Ÿ Elevon Throw Gauge Ÿ Instructional Manual. Building Tools:
Congratulations on your purchase of the TuffBirds Spec Racer Flying Wing. We Hope these build instructions will help you complete the build easily. Though the build itself doesn't take much time, just
More informationHot Stik ARF WARNING. Copyright 2005 Carl Goldberg Products LTD CARL GOLDBERG PRODUCTS, LTD.
Hot Stik ARF INSTRUCTIONS WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that
More informationPfalz E1 48. R/C Scale Model Instructions CONTACT INFORMATION. The Pfalz E1 was designed by M.K. Bengtson Prototype by Jack Richardson
Pfalz E1 48 Pfalz E1 48 R/C Scale Model Instructions CONTACT INFORMATION The Pfalz E1 was designed by M.K. Bengtson Prototype by Jack Richardson Manufactured and Distributed by: Bengtson Company e mail:
More informationInstruction Manual book
Instruction Manual book ITEM CODE BH53. SPECIFICATION Wingspan : 1,250mm 49.21 in. Length : 930mm 36.61in. Weight : 1.1kg 2.42 Lbs. Parts listing required (not included). Battery: 3 CELLS-LI-POLY-11.1V-2,500
More informationParkflyer F6F Hellcat
Parkflyer F6F Hellcat Page 1 of 19 MOLT MODELS Background Design Philosophy When I was first introduced to this hobby seventeen years ago I saw my first WWII warbird and I was hooked. Several years later
More informationRyan STA Sport Scale Model Aircraft Assembly and Instruction Manual
Ryan STA Sport Scale Model Aircraft Assembly and Instruction Manual Warning: This radio controlled model is not a toy. It requires skill to fly and is not recommended for the novice pilot. It should not
More informationDesigned by Steve Shumate Adapted from the North Star design by Laddie Mikulasko
Model Aero Polaris Specifications: Designed by Steve Shumate Adapted from the North Star design by Laddie Mikulasko Wing area: 343 sq in Span: 29.0" Length: 38.4" Weight RTF: 18 to 22 oz (prototype weighed
More informationRSM DISTRIBUTION Presents
RSM DISTRIBUTION Presents MOSQUITO By Jack Sheeks Photo _ Jack Sheeks Semi Scale Twin Stunter Wing Span: 58" Length: 37-3/4 Area: 579 sq. in. Engine: Two.35 -.40 www.rsmdistribution.com Call (951) 678
More informationModel Aero Aqua Cat, Aqua Cat SE, and Aqua Jet Build Guide
Model Aero Polaris Model Aero Aqua Cat, Aqua Cat SE, and Aqua Jet Build Guide Note: Aqua Cat SE and Aqua Jet specific instructions are at the end of the build guide. Some photos may depict the Polaris
More informationINS TRUC T I ON M A NU A L
INS TRUC T I ON M A NU A L Packing list: 1: PP F6F fuselage *1 2: Carbon tube 5*5*940mm *1 3: Pull rod *4 4: Motor mount *1 5: Quick rod adjuster *4 6: Hinge *4 7: M3 screws *4 8: Hook and loop tape *1
More informationTWEETY 25 INSTRUCTION MANUAL. Almost Ready to Fly Nitro/Electric Aerobat FEATURES SPECIFICATIONS
TWEETY 25 Almost Ready to Fly Nitro/Electric Aerobat INSTRUCTION MANUAL SPECIFICATIONS FEATURES WINGSPAN: 45.7 (1160mm) LENGTH: 38.6 (980mm) WING AREA: 370 sq in(24 sq dm) FLYING WEIGHT: Approx. 3.3 lbs
More informationPfalz E1 Monoplane 48 EZ Build Version
Pfalz E1 Monoplane 48 EZ BUILD Pfalz E1 Monoplane 48 EZ Build Version R/C Scale Model Instructions CONTACT INFORMATION Designed by M.K. Bengtson Prototype by Robert Hoffman Manufactured and Distributed
More informationTantrum Specifications
Tantrum Specifications Wingspan: 37in. (94cm.) Length: 37in. (94cm.) Wing Area: 370in 2 (2388cm 2 ) Weight (without battery): 10oz. (255g.) Wing Loading (depending on battery): 5.0 6.0oz/ft 2 Revision
More informationMiniacRC MIGHTY MINI P40 WARHAWK
Hand-Cutting and Skins) MiniacRC MIGHTY MINI P40 WARHAWK FliteTest style RC model Build Instructions Make sure that the orientation for molded pieces such as the scoop rings and landing gear housings are
More informationCleveland Quickie Luscombe Silvaire
Cleveland Quickie Luscombe Silvaire This plan package is not a 100% copy of the original kit. As you make your way through the instructions you will see the differences. Here s just a few of them: The
More informationSGTalon s Enterprise-A Foamie Build Guide. SGTalon s. Enterprise. Enterprise--A. Assembly Instructions
SGTalon s Enterprise SGTalon s Enterprise--A Enterprise Assembly Instructions Page 1 4-13-2013 SGTalon s Enterprise *******Recommended Hardware******** 2.6oz 250w Motor and Speed Control with 8x6 prop
More informationPrint template tiles and put together with clear tape to complete template.
Print template tiles and put together with clear tape to complete template. Cut each pattern out with scissors or use a razor and strait edge ruler. Use the ruler as a guide for the razor to get nice strait
More informationSTICK 2 IT. Fuselage Construction:
RCCD 2014 CLUB PROJECT STICK 2 IT Fuselage Construction: The fuselage is constructed without the use of a set of plans. The fuselage will be constructed on your previously prepared work surface and by
More informationBuilding a Giant Scale Electric EINDECKER Part 2
Building a Giant Scale Electric EINDECKER Part 2 John Bernard N1KUB AMA 58903 IMAA 28971 In Part-1 of this series, we explored the 100 Eindecker kit from SR Batteries and started building the fuselage.
More informationSebArt professional line
SebArt professional line Wind S 110 ARF ASSEMBLY MANUAL The new Wind S 110 ARF was designed by Italy aerobatic pilot, Sebastiano Silvestri. This professional ARTF kit is the result of Sebastiano s 20 years
More informationRequired Tools: Hobby Knife (# M917) Philips #1 Screwdriver Sanding Block (150grit) Pliers/Wire Cutters
Thanks for choosing the Combat Wings - XE2 as your next or first model airplane. The XE2 s wings are made from 100% EPP (expanded polypropylene) foam which is extremely durable. For this reason, the XE2
More information34" PELICAN by CRASH TEST HOBBY
34" PELICAN by CRASH TEST HOBBY The Pelican is a 34" trainer that can level its own wings and put its nose on the horizon once trimmed and balanced. It can handle more wind than most EZ flying planes in
More informationPfalz E1 36. R/C Scale Model Instructions CONTACT INFORMATION. The Pfalz E1 was designed by M.K. Bengtson Prototype by Ian Easton
Pfalz E1 36 Pfalz E1 36 R/C Scale Model Instructions CONTACT INFORMATION The Pfalz E1 was designed by M.K. Bengtson Prototype by Ian Easton Manufactured and Distributed by: Bengtson Company e mail: sales@aerodromerc.com
More informationBUILDING INSTRUCTIONS FOR FINEWORX. Miles. 2M Class Competition Glider. Congratulations! You have purchased our Miles, 2M Class Competition Glider.
BUILDING INSTRUCTIONS FOR FINEWORX Miles 2M Class Competition Glider Congratulations! You have purchased our Miles, 2M Class Competition Glider. The Miles is the first offering from FINEWORX, a new company
More information